0.58mm Gauge Pin Single ±0.001mm Accuracy 50mm Length Workshop Version - Metav IndustryLine

Take advantage of the combination of high precision (±0.001 mm) and a compact Ø 0.58 mm, 50 mm length for reliable go/no‑go checks and repeatable end‑measure inspections; the workshop‑ready design and protective transport box ensure safe handling and long service life. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification matching.

M323.058 Gauge pin — single precision probe, Ø 0.58 mm, ±0.001 mm

The M323.058 is a single gauge pin designed for fine workshop metrology and end‑measure verification in small‑bore and component inspection applications.

• Workshop version for daily workshop use
• Diameter 0.58 mm for fine measurements
• Tolerance ±0.001 mm high precision
• Packed in transport box for protection

Precision that secures process control and inspection repeatability

A tolerance of ±0.001 mm classifies this gauge pin among tools for high precision dimensional checks, enabling reliable discrimination of minute deviations during quality control. In practice, the tight tolerance reduces uncertainty when comparing measured bores or pin gauges to nominal values, which helps to avoid costly rework and to keep production tolerances stable. The specification is particularly suitable for small‑bore inspection where a 0.58 mm diameter probe is needed to check drilled holes, guide bores or fit features with minimal interference.

Robust, compact design for everyday workshop use

The probe combines a slim Ø 0.58 mm working section with a 50 mm shank length, offering a balance between reach and stiffness that supports repeatable manual handling. Made from special steel, the component resists wear while remaining easy to clean after use; the workshop version is optimised for frequent handling and routine measurements rather than laboratory isolation. Supplied in a protective transport box, the item is kept safe in transit and storage, reducing the risk of nicks or contamination that would degrade accuracy.

Faster inspection cycles and dependable traceability

Using a single, calibrated gauge pin cuts measurement set‑up time for small‑feature checks and simplifies inline or off‑line sampling plans. The compact geometry minimises operator influence, improving repeatability across multiple checks. For process control this means quicker decision cycles and a measurable reduction in throughput delays when comparing parts to master dimensions. The compact mass also supports stable seating in holders or fixtures where fine positional control matters, contributing to efficient and consistent inspection results.

For workshop procurement and application support, contact Metav Werkzeuge for specification advice and availability — technical consultants at Metav Werkzeuge in Emmerich can advise on integration and delivery options

Technical data

• Article number: M323.058
• GTIN: 4061905054105
• Manufacturer: Metav IndustryLine
• Label: Single gauge pin, Ø 0.58 mm, ±0.001 mm, length 50 mm

Core data

• Diameter: 0.58 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.003 kg

Features

• Material: Special steel
• Workshop version
• Supplied in transport box
• Category: Gauge pins
• SKU: M323.058

FAQ

What level of precision does this gauge pin provide?
The gauge pin offers a precision of ±0.001 mm, making the M323.058 suitable for high‑precision small‑bore checks and tight tolerance verification.

Is the probe suitable for routine workshop use?
Yes, the workshop version and special steel construction make this gauge pin robust for daily handling and repeated inspection tasks.

Which applications are typical for a 0.58 mm pin?
Applications include verification of small drilled holes, guide bores, plug‑gauge fitting tests and fine feature checks in mechanical components using the gauge pin M323.058.

How is the pin delivered to protect its accuracy?
The item is supplied in a transport box to prevent damage during storage and transport and to preserve the precision surface of the gauge pin.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com