0.85mm Test Pin Single ±0.001mm Accuracy Length 50mm Workshop Version - Metav IndustryLine

Benefit from workshop-grade accuracy with a tolerance of ±0.001 mm, a compact 0.85 mm diameter and a length of 50 mm, all produced from robust special steel for reliable reference measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin M323.085 — single 0.85 mm, ±0.001 mm, 50 mm (Metav IndustryLine)

A Gauge pin M323.085 designed as a compact, high-precision reference for end‑measurement and inspection tasks in workshop and toolroom environments

• Single gauge pin 0.85 mm diameter
• Tolerance ±0.001 mm for precise checks
• 50 mm hardened special steel shank
• Workshop version for robust daily use

Consistent accuracy for routine inspection

The inspection pin delivers repeatable accuracy thanks to its tight tolerance of ±0.001 mm, making it suitable for precise end‑measurements and setting tasks where small deviations matter. As a solid reference element, the pin minimises variability during quick checks and dimensional verification, which speeds up quality control cycles and reduces rework. The compact geometry supports confined measurement points while maintaining measurement confidence typically required in precision toolmaking.

Robust design built for everyday workshop use

Manufactured from special steel and supplied in a workshop variant, the measuring pin is engineered to withstand frequent handling and fixture mounting. The 50 mm shank provides sufficient engagement for stable seating while remaining easy to manipulate with tweezers or collets. Surface finishing and material choice favour durability and resistance to wear, so calibration intervals can be extended under normal use, contributing to lower total inspection costs over time.

Integrating the pin into measurement routines

As a single reference element, this inspection pin serves effectively as a go/no‑go reference, centre locator or end‑stop in jigs and fixture setups. Its 0.85 mm diameter is ideal for small bores, pin gauges and fine mechanical parts, supporting accurate alignment during assembly and setup operations. Using standard measurement procedures and appropriate holding fixtures ensures the pin’s tolerance is fully exploitable in day‑to‑day workflows, increasing throughput without sacrificing measurement certainty.

Handling, storage and traceability considerations

Given the fine diameter and high precision, the pin benefits from careful handling and protected storage to preserve the ±0.001 mm specification. When incorporated into inspection routines, document the reference usage and inspection outcomes to maintain traceability and support quality records. For workshops seeking to centralise measuring resources, these pins act as low‑footprint yet high‑value tools that complement existing gauge sets and precision instruments.

For workshop‑grade measurement accuracy from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for ordering or technical advice via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.085
• GTIN: 4061905054044
• Brand: Metav IndustryLine

Facts

• Diameter: 0.85 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.003 kg

Special features

• Material: special steel
• Single inspection/gauge pin
• Workshop execution
• Intended for end‑measurement and reference tasks

FAQ

What level of accuracy does this gauge pin provide?
The gauge pin M323.085 from Metav IndustryLine is specified with an accuracy of ±0.001 mm, suitable for fine inspection and reference measurements.

Can the pin be used for small bore inspection and alignment?
Yes, the 0.85 mm diameter and 50 mm length make the M323.085 ideal for small bore checks, alignment and fixture positioning in precision toolrooms.

How should the inspection pin be handled and stored?
Handle the pin with care to avoid impact or contamination; store in a protective holder to maintain the ±0.001 mm specification and ensure long service life.

Is this pin supplied as a single item or part of a set?
The product is offered as a single gauge pin (SKU M323.085) in a workshop execution, suitable for individual replacement or for assembling into bespoke gauge sets.

Which applications suit this gauge pin best?
The M323.085 is suited to end‑measurements, reference checks, small part inspection and fixture set‑up in workshops, toolrooms and inspection benches.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com