0.97mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine

Benefit from high‑precision inspection and workshop‑ready robustness: the M323.097 delivers Ø 0.97 mm nominal size with ±0.001 mm tolerance and a stable 50 mm length for repeatable end‑measurement tasks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration into existing inspection routines.

M323.097 gauge pin (precision test pin) – Ø 0.97 mm, ±0.001 mm (Metav IndustryLine)

A M323.097 gauge pin designed for precise end‑measurement and plug inspection in metrology benches and workshop inspection stations.

*Workshop version for robust use *Diameter Ø 0.97 mm with ±0.001 mm accuracy *Length 50 mm for stable handling *Manufactured from special steel

Precision where micrometres make the difference

This gauge pin provides a ±0.001 mm tolerance that supports micrometre‑level inspection and determination of end dimensions. The very small nominal diameter (Ø 0.97 mm) and the close tolerance make the component suitable for fine plug checks, go/no‑go verification and reference fits in precision assemblies. In practice, the stated tolerance corresponds to a one‑micrometre window around the nominal size, ensuring measurable, comparable results on bench comparators and high‑resolution optical systems. The compact mass and consistent geometry reduce measurement uncertainty caused by tilt or misalignment, so results are more readily reproducible in routine quality checks.

Durable design for workshop and inspection use

Constructed from special steel, the pin combines surface integrity with dimensional stability under normal workshop conditions. The 50 mm length gives a good contact area for clamping or seating in holders while remaining easy to position by hand or in fixtures; the low mass (approx. 0.003 kg) minimises undesired deflection. The designation as a workshop variant reflects reinforced handling and finish standards suited to repetitive use, while the single‑piece supply format simplifies inventory control for inspection sets and gauge kits. The robust material choice also supports routine cleaning and light maintenance without compromising dimensional integrity.

Practical integration into measurement workflows

The precision test pin is intended for end‑measurement routines, reference checks and fit trials within precision machining and inspection processes. Its compact dimensions allow use in confined setups or as a reference in multi‑pin jigs and bespoke fixtures. Traceable identification (SKU and GTIN) eases catalogue integration and part tracking in quality systems. Because the component is a standard gauge‑type element, it slots into existing verification sequences with minimal adaptation, helping to reduce cycle time for inspection steps and maintain measurable process control across batch inspections.

For tailored advice on incorporating the M323.097 into inspection equipment or for procurement from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for direct supply and application support.

Technical data

• SKU: M323.097
• GTIN: 4061905055010
• Category: Gauge pins (Messstifte)
• Brand: Metav IndustryLine

Facts

• Nominal diameter: 0.97 mm
• Length: 50 mm
• Accuracy / tolerance: ±0.001 mm
• Weight: 0.003 kg

Special features

• Material: special steel
• Delivery format: single piece
• Intended use: end‑measurement / plug inspection
• Version: workshop execution (Werkstatt‑Ausführung)

FAQ

What tolerance does this gauge pin offer? The M323.097 gauge pin is manufactured to a tolerance of ±0.001 mm, suitable for micrometre‑level verification tasks.

What are the pin’s dimensions and mass? The test pin has a nominal diameter of 0.97 mm, a length of 50 mm and a mass of approximately 0.003 kg.

Which material is used for the gauge pin? The M323.097 is made from special steel, selected for dimensional stability and workshop durability.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com