1.13mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine

Take advantage of a highly precise workshop test pin with a ±0.001 mm tolerance and a compact 1.13 mm diameter for reliable end‑measure checks; the hard‑working construction and defined 50 mm length support repeatable inspection routines. Order the gauge pin M323.113 directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin M323.113 – workshop test pin, 1.13 mm, ±0.001 mm tolerance

A compact gauge pin designed for fine bore verification and end‑measure checks in workshop environments, combining tight dimensional control with robust everyday handling.

• High precision ±0.001 mm tolerance
• Diameter 1.13 mm for fine bore checks
• 50 mm special-steel length
• Workshop version for robust daily use

Repeatable precision for end‑measure verification

The compact test pin delivers ±0.001 mm positional certainty, making it suitable for tasks where small deviations affect assembly fit or functional clearance. This level of tolerance translates to measurable savings: fewer rejected parts, reduced rework and a clearer go/no‑go decision during incoming inspection or final checks. The slim 1.13 mm diameter and calibrated geometry provide a stable reference for bore checks and plug‑gauge substitutes, while the fixed 50 mm length ensures consistent contact depth when used with gauge blocks, templates or simple fixtures. The combination of fine resolution and defined geometry supports reliable statistical process control in small‑part production.

Built for workshop use: material and handling benefits

Manufactured in special steel, the pin is specified for workshop conditions where handling and routine use demand dimensional stability and wear resistance. The workshop version designation indicates a product balanced between precision and robustness: it withstands daily handling and insertion cycles yet retains the measured form that inspection depends on. The compact mass also simplifies manual manipulation and decreases the risk of impact damage during inspection runs. Where traceable measurement references are needed within production, the pin serves as a pragmatic tool for spot checks, bench testing and assembly verification without requiring elaborate setup.

Practical application and installation in inspection routines

The single‑piece delivery supports targeted checks or replenishing mixed gauge sets; its modest weight (approx. 0.003 kg) and defined geometry make it easy to position in small bores and hard‑to‑reach cavities. The test pin integrates readily with length stops, mandrels and simple jigs, and its 1.13 mm diameter is suitable for precision fits in instrumentation, micro‑mechanics and connector manufacturing. For repeatable results, use a consistent insertion technique and a clean contact surface; when combined with calibrated reference blocks or micrometric fixtures, the pin becomes part of a cost‑effective quality control chain that emphasises measurable outcomes over complex processes.

Choose the Metav IndustryLine gauge pin M323.113 for precise end‑measure tasks and contact Metav Werkzeuge for tailored advice and reliable delivery from Emmerich.

Technical data

• Article number: M323.113
• GTIN: 4061905056925
• Brand: Metav IndustryLine
• Material: Special steel

Facts

• Diameter: 1.13 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.003 kg

Special features

• Workshop execution
• Single piece delivery
• Category: Gauge pin
• Suitable for fine bore and end‑measure verification

FAQ

What is the intended use of this test pin?
The gauge pin M323.113 is intended for fine bore checks and end‑measure verification in workshop and small‑part inspection tasks.

Is the material suitable for repeated inspection cycles?
Yes, the test pin is made from special steel and the workshop version is designed for robust daily use while maintaining dimensional stability.

Can the pin be integrated with existing jigs and fixtures?
Integration is straightforward: the 1.13 mm diameter and 50 mm length fit common mandrels, stops and micro‑fixtures used in precision inspection.

What accuracy can be expected during routine checks?
Routine inspections using the gauge pin M323.113 benefit from the stated ±0.001 mm tolerance, supporting consistent go/no‑go decisions and reduced rework.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com