1.42mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine

Compact, workshop-grade precision with a guaranteed micro tolerance and robust stainless-feel finish: the combination of ±0.001 mm tolerance, 1.42 mm nominal diameter and a 50 mm length ensures reliable end‑measurement checks in serial inspection and setup tasks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin M323.142 by Metav IndustryLine — 1.42 mm diameter, ±0.001 mm tolerance

The Gauge pin M323.142 is a single test pin designed for precise end‑measurement tasks and reference fitting in workshop and inspection environments.

• Tolerance ±0.001 mm
• Diameter 1.42 mm
• Length 50 mm
• Special‑steel construction

Precision where it counts for repeatable inspection results

The gauge pin delivers a manufacturable micro tolerance of ±0.001 mm, which translates directly into measurable improvements in first‑off verification and in‑process spot checks. Such a fine tolerance reduces uncertainty when establishing reference fits or checking end dimensions, enabling higher confidence in pass/fail decisions. Thanks to the compact 1.42 mm diameter and the slim 50 mm shaft, the component is especially suited to small bores, dowel seats and dimensional references where space is limited but repeatability is crucial.

Workshop durability and handling that supports busy production

Made from special steel, this workshop‑grade pin resists wear during repeated seating and extraction, preserving the critical diameter tolerance over time. The modest mass and straight shank geometry simplify handling during assembly and inspection, while the 50 mm length provides reach for recessed features without sacrificing stiffness. Built as a single test pin for quick interchange in pin sets or fixture pockets, the component combines low handling effort with robust metrological properties to keep throughput steady.

Integrating the pin into quality control workflows

Traceability and procurement are straightforward: the part is available under SKU M323.142 with GTIN for order and inventory management. Use the pin as a reference in gauging fixtures, as a go/no‑go seating reference, or as a datum when setting up small assemblies; its geometry makes it compatible with standard pin guides and hardened locating bores. The compact form factor supports tight tolerances in serial production and helps reduce rework by improving the clarity of inspection tolerances at the operator level. Metav IndustryLine's catalogue position ensures consistent availability for routine replacement and set replenishment.

For application guidance or to secure workshop‑grade M323.142 pins from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for fast procurement and technical advice: info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.142
• GTIN: 4061905057502
• Manufacturer: Metav IndustryLine

Facts

• Nominal diameter: 1.42 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.003 kg
• eClass: 21170231

Special features

• Material: special steel
• Workshop execution
• Story trigger: end measurements

FAQ

What is the achievable measurement tolerance with this gauge pin?
The gauge pin offers a tolerance of ±0.001 mm, making it suitable for micro‑precision end‑measurements and reference seating.

Is the pin suitable for use in small bore gauging and dowel checks?
Yes, the 1.42 mm diameter and 50 mm length make the test pin ideal for small bore inspection, dowel seat checks and tight‑fit references.

Which material is the gauge pin made from and what does that mean for wear resistance?
The pin is manufactured from special steel, selected to balance hardness and resistance to wear under frequent seating and extraction in workshop conditions.

How is the product identified for ordering and inventory?
Order using SKU M323.142 or GTIN 4061905057502; the part is listed under Metav IndustryLine for consistent procurement.

Can the pin be used as a datum in fixture set‑ups?
Yes, the pin’s straight shank and precision tolerance make it suitable as a datum or reference for fixture alignment and small‑part assembly checks.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com