1.8mm Gauge Pin, ±0.001mm Tolerance, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine

Take advantage of workshop-grade construction, ±0.001 mm accuracy and a compact 50 mm length to secure reproducible end measurements and minimise rework. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin M323.180 — 1.80 mm diameter, ±0.001 mm tolerance (Metav IndustryLine)

Gauge pin M323.180 for precise end-measurement and small-bore inspection in workshop environments

• Workshop-grade precision construction
• Diameter 1.80 mm with ±0.001 mm tolerance
• Hardened special steel for wear resistance
• 50 mm length for deep bore checks

Precision that reduces rejects and speeds up inspection

A nominal diameter of 1.80 mm with a tight ±0.001 mm tolerance ensures highly reproducible results when verifying end dimensions or setting limit gauges. The very small dimensional deviation lowers statistical process variation and supports faster go/no-go decisions on the shop floor. By converting the dimensional specification into a measurable production control point, the component acceptance rate stabilises and downstream rework is reduced.

Robust construction made for everyday workshop use

Manufactured from special steel and specified as a workshop version, the pin is designed to withstand frequent handling and routine inspection cycles. The material choice and heat treatment provide improved surface hardness and abrasion resistance, which helps retain dimensional stability over many inspection cycles. The result is a tool that keeps measurement uncertainty low while requiring only basic maintenance.

Compact geometry for tight spaces and deep bores

With a 50 mm overall length and a mass of 0.004 kg (4 g), the pin is easy to manoeuvre into restricted bores and cavities. The small form factor makes the tool suitable for checking end dimensions, verifying seating depths and aligning small assemblies where access is limited. Its light weight reduces the influence of operator handling on repeatability when used with standard inspection fixtures.

Practical benefits for procurement and quality assurance

Supplied individually and identified for traceability, this gauge pin supports lean stock management and clear part handling. The combination of workshop-ready design and tight tolerance makes it suitable as a go/no‑go reference pin or as a limit check in routine quality control. Procuring from a supplier that acts as a quality filter for the European market helps streamline logistics and ensures product consistency across batches.

For technical advice or to secure supply of Metav IndustryLine gauge pins such as M323.180, contact Metav Werkzeuge in Emmerich for tailored assistance and reliable delivery via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.180
• GTIN: 4061905054785
• Brand: Metav IndustryLine

Facts

• Diameter: 1.80 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.004 kg

Special features

• Material: Special steel
• Workshop version
• Supplied individually
• Accuracy class: ±0.001

FAQ

What are the nominal diameter and tolerance for this gauge pin?
The nominal diameter is 1.80 mm with a tolerance of ±0.001 mm for the gauge pin M323.180 from Metav IndustryLine.

Which inspection tasks is this pin intended for?
The pin is intended for end‑measurement checks, small bore validation and setup tasks where precise dimensional control of end faces is required.

Is the design suitable for regular workshop handling?
Yes — the workshop‑grade construction and special steel material make the pin robust enough for frequent use in production and inspection routines.

How should the pin be maintained to preserve accuracy?
Clean after use, protect from impact and corrosion, and store in a dedicated protective container to maintain surface condition and dimensional stability.

How is the product identified for traceability?
Identification is provided via SKU M323.180 and GTIN 4061905054785 for inventory and quality records

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com