2.02mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine

Take advantage of the combination of industrial‑grade accuracy (±0.001 mm), a stable 2.02 mm diameter and a compact 50 mm length to ensure reproducible end‑measurements and fast fit checks on the shop floor. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin M323.202 – single test pin, 2.02 mm diameter, ±0.001 mm accuracy (Metav IndustryLine)

The gauge pin M323.202 is a compact workshop test pin designed for precise end‑measurements and fit verification in confined or series inspection tasks.

• High‑precision ±0.001 mm tolerance
• Compact 2.02 mm diameter for fine fits
• Robust special steel construction
• 50 mm length for secure contact and reach

Precision that secures assembly tolerances

A high degree of measuring certainty is essential for reliable parts inspection. With a declared tolerance of ±0.001 mm, this single test pin provides the metrological stability required for micro‑fits, plug gauges and end‑measure checks. The small nominal diameter of 2.02 mm makes the component suitable for tight bores and fine mechanical interfaces; the narrow profile reduces interference during insertion and supports fast, repeatable checks. The combination of these features helps to reduce rework and process variability in routine quality control.

Built for repeatable inspection and fast go/no‑go checks

The elongated 50 mm shaft delivers secure engagement with the measured feature and permits consistent contact geometry on every measurement. At approximately 0.004 kg, the element is light enough for handheld gauging yet rigid enough to avoid unwanted bending during short, repetitive operations. The workshop specification ensures a balance between robust handling and dimensional integrity, so the pin is effective for both bench and fixture use when verifying end dimensions or mating fits.

Integrates into existing measurement routines with minimal setup

Designed as a single, purpose‑driven test element, this gauge pin slots into established inspection routines without the need for special adapters. Its compact size allows access to restricted zones that larger gauges cannot reach, while the straightforward geometry simplifies traceability in inspection logs. Using a standard, single‑element pin speeds up cycle times for checks that would otherwise require more complex tooling, supporting lean inspection workflows and faster throughput.

Durable material choice and dependable provenance

Manufactured from special steel, the pin resists wear under normal contact use and maintains dimensional stability across repeated cycles. As part of the Metav IndustryLine, the component benefits from a supplier network focused on dependable supply and consistent quality control—attributes that matter when the same gauge is used across multiple shifts and operators. For applications where traceability or certification is required, Metav Werkzeuge can advise on calibration options and documentation to match quality‑management needs.

For proven small‑diameter gauging components from Metav IndustryLine, contact Metav Werkzeuge for technical guidance and order processing — rapid supply from Emmerich ensures the test pin reaches the workshop when required.

Technical Data

• Article number: M323.202
• GTIN: 4061905056741
• Manufacturer: Metav IndustryLine

Core technical data

• Diameter: 2.02 mm
• Length: 50 mm
• Tolerance/accuracy: ±0.001 mm
• Weight: 0.004 kg

Special features

• Material: special steel
• Version: workshop execution
• Application: end‑measurements, fit verification
• Story trigger: end measurements

FAQ

What level of accuracy does this test pin offer?
The gauge pin M323.202 is specified with an accuracy of ±0.001 mm, making it suitable for high‑precision end‑measurements and fit checks in workshop inspection routines.

Is the pin suitable for use in small bores or threaded holes?
Yes. The 2.02 mm diameter and compact profile are specifically intended for narrow bores and fine fit verifications where access is restricted.

What material is the pin made from and how durable is it?
The shaft is manufactured from special steel, selected to retain dimensional stability and resist wear under normal inspection cycles.

Can the pin be used in fixture or bench‑mounted gauges?
The 50 mm length and robust shaft permit integration into simple fixture setups or handheld checks; Metav Werkzeuge can advise on fixturing options for series testing.

Does the product come with manufacturer identification for traceability?
The product is supplied as part of the Metav IndustryLine range (SKU M323.202, GTIN 4061905056741), which supports traceability in documented inspection procedures.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com