8.17mm Gauge Pin, Workshop Version, ±0.001 mm Accuracy, 50mm Length - Metav IndustryLine

Take advantage of precise, repeatable checks with a compact, workshop‑grade gauge pin that combines ±0.001 mm tolerance and a robust special steel construction for dependable in‑process inspection. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application guidance.

Gauge pin, 8.17 mm ±0.001 mm — Workshop version (Metav IndustryLine)

Gauge pin, 8.17 mm ±0.001 mm is a single‑piece inspection pin intended for dimensional end checks and fixture setting in workshop environments

• Workshop version for daily use
• Diameter 8.17 mm ±0.001 mm precision
• 50 mm overall length for stable handling
• Supplied in protective transport case

Accurate tolerance for repeatable inspection

The gauge pin is manufactured to a nominal diameter of 8.17 mm with an accuracy of ±0.001 mm, delivering high precision for go/no‑go checks, alignment and end‑measurement tasks. This level of tolerance reduces uncertainty in pass/fail decisions and minimises rework by ensuring that each verification is directly comparable to the nominal size. The compact geometry and fine finish support consistent contact conditions, which is essential when multiple operators perform short, repeat inspections during production runs.

Robust build tailored to workshop conditions

Produced from special steel, the pin offers a balance of hardness and toughness suitable for frequent handling in a workshop setting. With a length of 50 mm and a low mass (approx. 0.025 kg), the component is easy to position and manoeuvre while providing enough gripping length for stable use in jigs and fixtures. The workshop version designation indicates practical attention to everyday demands: corrosion‑resistant surface quality, repeatable seating in holders, and straightforward cleaning. The item is supplied in a transport case to protect the gauge during storage and transit.

Streamlined inspection workflow and compatibility

As a single‑gauge solution, the pin supports quick setup for dimensional verification and fixture setting, helping to shorten inspection cycles and improve throughput. The clearly defined nominal and tolerance values facilitate integration into inspection plans and documentation. Marked with its product code and identifiable by its characteristic finish, the component is suitable for use in conventional measurement benches and as an end reference in gauge stacks, contributing to repeatable results across shifts without complex calibration requirements specified in the baseline data.

For reliable workshop gauging, request the Metav IndustryLine gauge pin (M323.817) from Metav Werkzeuge — contact via info@metav-werkzeuge.com or call +49 2822 7131930 for order details and application advice

Technical data

• Article number: M323.817
• GTIN: 4061905060571
• Brand: Metav IndustryLine
• Material: Special steel

Facts

• Nominal diameter: 8.17 mm
• Tolerance: ±0.001 mm
• Length: 50 mm
• Weight: 0.025 kg

Special features

• Workshop version
• Supplied in transport case for transit protection
• Intended for end‑measurement and fixture setting
• Compact, single‑piece gauge pin design

FAQ

What are the nominal diameter and tolerance of the pin? The gauge pin M323.817 has a nominal diameter of 8.17 mm and a tolerance of ±0.001 mm.

Which material is used for this gauge pin? This Metav IndustryLine gauge pin is made from special steel, chosen for wear resistance and stable contact behaviour.

Is the pin suitable for end‑measurements and fixture setting? Yes. The M323.817 is designed for end measurements and as a reference element in fixture alignment and quick verification tasks.

How is the product supplied for transit? The gauge pin M323.817 is supplied in a protective transport case to prevent damage during handling and transport.

What routine maintenance is recommended? Regular cleaning, inspection for wear marks and light corrosion protection are recommended; store the pin in its transport case when not in use.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com