8.34mm Gauge Pin, ±0.001mm Tolerance, 50mm Length, Workshop Version, Special Steel, Case Included - Metav IndustryLine

Take advantage of the combination of ultra‑fine tolerance and robust workshop construction to ensure reliable end‑measure checks and fewer rework cycles. Order the pin directly via Metav Werkzeuge or consult our specialists for application advice.

M323.834 Gauge pin — single precision 8.34 mm, ±0.001 mm (Metav IndustryLine)

A M323.834 single gauge pin designed for precise end‑measurement and fit checks in workshop inspection and assembly routines

• High‑precision ±0.001 mm tolerance
• Nominal diameter 8.34 mm
• Length 50 mm for stable handling
• Workshop‑grade special steel construction

Precision that secures measurement decisions

The gauge pin offers an industry‑grade tolerance of ±0.001 mm, which makes it suitable for final dimension checks where decisive go/no‑go criteria are required. Manufactured for workshop use, the component removes doubt from tight fits and assembly controls by providing a direct physical reference for bore and shaft acceptance. The ultra‑fine tolerance reduces the need for secondary measurement steps and supports faster, evidence‑based decisions in production control.

Robust construction for repeatable handling

Constructed from special steel and specified at 50 mm length, the pin combines surface integrity with a handling form factor that eases repeated use on the inspection bench. The workshop execution prioritises wear resistance and dimensional stability so that periodic checks remain consistent over time. The compact mass also minimises thermal influence during short measurement cycles, preserving reproducibility between successive measurements.

Integration into inspection workflows to save time

As a single gauge pin for verification tasks, this tool fits directly into common inspection routines such as plug checks, assembly trials and fixture validation. Using a defined physical standard like this simplifies process documentation and reduces throughput time for routine acceptance tests. The traceable reference and simple geometry support rapid comparison methods and are compatible with standard pin blocks, holders and test benches used across mechanical workshops.

Traceability and item identification for quality control

Each item is identifiable by its SKU M323.834 and GTIN, aiding traceability within inventory and quality records. The clearly defined numerical data — diameter, length and stated tolerance — provides a verifiable basis for batch acceptance and calibration scheduling. When documented alongside inspection reports, the pin helps demonstrate conformance to internal quality plans and supports downstream decisions in assembly and supply chain checks.

Contact Metav Werkzeuge in Emmerich for tailored advice on integrating this precision gauge pin into inspection routines or to discuss procurement and delivery options

Technical data

• SKU: M323.834
• GTIN: 4061905062469
• Manufacturer: Metav IndustryLine
• Label: Prüfstift, einzeln, 8,34mm, +/- 0.001 mm Länge 50 mm
• Material: Special steel

Facts

• Diameter: 8.34 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.026 kg
• ECLASS: 21170231

Special features

• Workshop execution
• Single item delivery
• Designed for end‑measure and fit checks

FAQ

What accuracy can be expected from this gauge pin?
The M323.834 gauge pin is specified to ±0.001 mm and is intended for precision end‑measure and go/no‑go checks where micrometric accuracy is required.

Is the pin suitable for everyday workshop use?
Yes, the workshop‑grade construction and 50 mm length make the pin robust enough for regular inspection tasks while maintaining repeatable results.

Which materials is the pin suited to verify?
The gauge pin itself is a hardened reference made from special steel and is used to check bores and shafts in a wide range of materials; it provides a physical reference independent of the workpiece material.

How is the item identified for inventory and quality records?
Identification is via SKU M323.834 and GTIN 4061905062469, which simplifies traceability in inspection and purchasing systems.

Can this gauge pin be used with standard pin blocks and holders?
The pin is manufactured to nominal dimensions and is compatible with common pin blocks, holders and bench fixtures used in mechanical workshops.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com