8.87mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine

Take advantage of the combination of ultra‑fine tolerance, a compact diameter and robust special steel construction for reliable end‑of‑line checks and reproducible go/no‑go trials. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice.

Gauge pin, single — 8.87 mm, ±0.001 mm, 50 mm (Metav IndustryLine)

A gauge pin designed for end‑measurement and functional checking in workshop and inspection environments, suited to tight tolerances and repeatable seating.

• High tolerance ±0.001 mm
• Diameter 8.87 mm ground to size
• Length 50 mm for secure seating
• Workshop version for robust handling

Precision that reduces rework and speeds inspection

The pin delivers an exceptionally fine tolerance of ±0.001 mm, which translates into micrometric certainty when validating bore sizes, pins and mating parts. This level of accuracy reduces downstream rework and scrap by making first‑pass inspections decisive. The reduced uncertainty supports rapid go/no‑go decisions in production and quality control, shortening inspection cycles while maintaining traceability for documented checks.

Robust materials for repeated use in workshop conditions

Manufactured from special steel, the component resists wear during repeated insertion and removal cycles. Hardness and surface finish are optimised to preserve diametral accuracy over many uses, meaning fewer replacements and lower life‑cycle costs. The workshop version is configured to tolerate handling typical in assembly and inspection stations without sacrificing the dimensional stability required for precision gauging.

Practical advantages for everyday metrology tasks

With a nominal diameter of 8.87 mm and an overall length of 50 mm, the pin is long enough to engage bores and locate features reliably while remaining compact for bench use. The slim form factor enables access to confined seats and ensures consistent contact geometry, which stabilises readings and simplifies fixture design. The mass‑balanced profile and ground finish make it suitable for chain inspection work where repeatability is essential.

Traceability and identification for quality workflows

Each unit is identifiable by its SKU and GTIN, facilitating inventory and inspection record management. The low mass and compact dimensions support easy handling and simple fixturing for automated or manual checks. As a dedicated end‑measurement tool, the pin integrates into existing inspection procedures and complements plug, ring and snap gauge sets where precise reference sizes are required.

Contact Metav Werkzeuge GmbH for tailored advice on integrating the Metav IndustryLine gauge pin into inspection routines, or request a technical datasheet and availability information from Metav Werkzeuge via info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.887
• GTIN: 4061905064470
• Brand: Metav IndustryLine

Facts

• Diameter: 8.87 mm
• Length: 50 mm
• Tolerance: ±0.001 mm
• Weight: 0.028 kg

Special features

• Material: Special steel
• Version: Workshop execution
• Application: End measurements
• ECLASS: 21170231

FAQ

Is this pin suitable for high‑precision bore checks?
Yes. The gauge pin with a diameter of 8.87 mm and ±0.001 mm tolerance is intended for high‑precision bore and seating checks and is supplied as a single, ground reference pin.

Can the Metav IndustryLine pin be used in automated inspection fixtures?
The design and balanced geometry of the M323.887 make the pin suitable for fixtures and automated jigs where consistent seating and low runout are required.

What maintenance is recommended to preserve accuracy?
Regular cleaning and avoidance of impact preserve the ground diameter; lubrication is not required for dimensional stability but light rust prevention is advisable for storage of the special steel piece.

Is the pin traceable for quality documentation?
Identification via SKU and GTIN allows traceable records; include the M323.887 reference in inspection protocols to document usage and batch control.

Which applications is this gauge pin optimised for?
Optimised for end measurements and go/no‑go seating checks in machining, assembly and inspection environments where micrometric tolerances are mandated.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com