9.5mm Gauge Pin Single, ±0.001mm Tolerance, 50mm Length, Workshop Grade - Metav IndustryLine

Reliable dimensional reference and robust workshop design ensure repeatable inspection results; the combination of ±0.001 mm tolerance and special steel construction supports precise end-measurement tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

M323.950 gauge pin – 9.50 mm diameter, ±0.001 mm, workshop version (Metav IndustryLine)

M323.950 is a single precision gauge pin for dimensional reference and end-measure checks in workshop and production inspection.

• Workshop version for robust daily use
• Diameter 9.50 mm with ±0.001 mm accuracy
• Length 50 mm for deep or through-hole checks

Reliable reference for quality control tasks

The M323.950 precision gauge pin serves as a stable reference for dimensional checks where micrometre-level accuracy is required. With a nominal diameter of 9.50 mm and an indicated tolerance of ±0.001 mm, the pin provides a measurable baseline for go/no-go verification and comparison measurements. Its special steel construction offers the rigidity needed to maintain form under frequent handling, helping to reduce measurement scatter and improve reproducibility in workshop inspection routines.

Fast, repeatable checks that save inspection time

Designed as a workshop version, this single gauge pin focuses on practicality and endurance during routine use. The 50 mm length allows for straightforward probing of deeper features and through-holes while keeping handling simple; the low mass (0.032 kg) contributes to nimble operation in tight setups. By providing a consistent reference diameter, the pin shortens inspection cycles and supports efficient quality-control workflows without sacrificing measurement confidence.

What ±0.001 mm tolerance means in practice

A tolerance of ±0.001 mm corresponds to one micrometre of permissible deviation, a level of precision suited to fine mechanical assemblies and toolroom verification. For many production and maintenance tasks, such narrow tolerance reduces ambiguity when assessing fit and clearance; it distinguishes between rough checks and precision verification. The gauge pin functions as an objective standard for end-measure comparisons, making dimensional decisions traceable and less dependent on operator judgement.

Applications and compatibility in the workshop

This single gauge pin is tailored for use in machine shops, toolrooms and assembly inspection benches as an end measure or reference probe. Typical applications include checking bore diameters, validating mandrels and verifying alignment in fixtures. The compact format and robust material make it suitable for repeated contact with metallic components; the item is supplied individually to allow selective introduction into inspection sets or fixture arrays as required.

For ordering and expert guidance on precision gauges from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss suitability and delivery options.

Technical data

• Article number: M323.950
• GTIN: 4061905065859
• Brand: Metav IndustryLine
• Label: Gauge pin, single, 9.50 mm, ±0.001 mm, length 50 mm

Facts

• Diameter: 9.50 mm
• Length: 50 mm
• Accuracy / tolerance: ±0.001 mm
• Weight: 0.032 kg

Special features

• Material: special steel
• Delivery: single gauge pin (einzeln)
• Intended use: end-measure / reference checks
• Version: workshop execution (Werkstatt-Ausführung)

FAQ

What tolerance does the gauge pin provide?
The M323.950 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometre-level reference accuracy for inspection tasks.

What material is used for the pin?
The gauge pin is made from special steel, chosen for dimensional stability and wear resistance in workshop environments.

Is the gauge pin supplied individually or in sets?
This item is supplied individually as a single gauge pin for selective use in inspection routines.

Which applications are suitable for this gauge pin?
The pin is intended for end-measure and reference checks, such as bore validation, fixture verification and through-hole inspection in machine shops and toolrooms.

Does the 50 mm length support deep-hole checking?
A 50 mm length offers practical reach for deeper bores and through-holes while remaining straightforward to handle in fixtures.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com