10.74mm Gauge Pin, 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine

Compact workshop-grade gauge pin combining tight tolerance and robust special‑steel construction for reliable inspection and fixture checks. Benefit from the precise 10.74 mm nominal diameter and the 50 mm length for consistent end‑measure verification. Order the gauge pin directly via Metav Werkzeuge or ask the consultants if needed.

Gauge pin M323.A74 — single inspection pin, Ø 10.74 mm, 50 mm length (Metav IndustryLine)

The gauge pin, single, Ø 10.74 mm, 50 mm length is a workshop‑grade inspection pin engineered for end‑measure checks, fixture alignment and repeatable verification tasks in production and quality control environments.

• Workshop‑grade construction for daily use
• Nominal diameter 10.74 mm for precise fits
• Length 50 mm suited to fixture and end‑measure checks
• Specified tolerance ±0.002 mm for tight control

Reliable measurement where tolerances matter

The M323.A74 inspection pin offers highly predictable dimensional behaviour, making it suitable for verification tasks where small deviations have real cost implications. With a specified tolerance of ±0.002 mm, the pin supports stringent acceptance criteria and helps reduce scrap and rework through faster go/no‑go decisions. The 10.74 mm nominal diameter is held to tight limits, which benefits both pass/fail gauging and setup procedures; the result is improved throughput because fewer secondary checks are needed and first‑pass yields increase.

Robust design for workshop inspection and handling

Built in a workshop‑grade variant from special steel, this single test pin tolerates repeated handling and routine use in jigs and fixtures without compromising form. The 50 mm shank length gives sufficient engagement for secure seating in inspection blocks and supports end‑measure checks on small to medium components. The chosen material and finish resist minor wear and maintain consistent contact geometry, which is essential when the same pin is used across multiple stations or hand‑held inspections over a production shift.

Streamlined use within quality workflows

Integration into quality routines is straightforward: the pin functions as a reliable reference for end‑measure verification, go/no‑go checks and fixture alignment. Its compact dimensions and modest mass (approx. 0.1 kg) make handling and rapid changeover simple, supporting lean inspection cycles. Documentation and traceability are facilitated by the clear article identification, enabling orderly stock and calibration planning within a shop floor system. For project or batch enquiries, Metav IndustryLine offers product information and specification guidance to match the pin to inspection demands.

For workshop‑grade precision and dependable inspection results, request the Metav IndustryLine gauge pin M323.A74 from Metav Werkzeuge — our consultants in Emmerich will advise on application and delivery

Technical data

• SKU: M323.A74
• GTIN: 4061905066597
• Brand: Metav IndustryLine

Facts

• Nominal diameter: 10.74 mm
• Length: 50 mm
• Specified tolerance: ±0.002 mm
• Weight: 0.1 kg

Special features

• Material: special steel
• Workshop version for routine use
• Single test / inspection pin
• Category: Messstifte

FAQ

What nominal diameter does the pin have?
The gauge pin is specified with a nominal diameter of 10.74 mm (article M323.A74, Metav IndustryLine).

What tolerance is specified for dimensional control?
The inspection pin carries a specified tolerance of ±0.002 mm for tight acceptance criteria and repeatable gauging.

Which material is used for the pin?
The pin is manufactured from special steel and offered as a workshop‑grade inspection component under the Metav IndustryLine brand.

What are the length and typical handling characteristics?
Length is 50 mm and mass is approximately 0.1 kg, providing a compact, easy‑to‑handle inspection reference (SKU M323.A74).

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com