11.67mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine

Compact 11.67 mm diameter, ±0.002 mm tolerance and a 50 mm shaft combine to provide dependable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin, single 11.67 mm — 50 mm length, ±0.002 mm (Metav IndustryLine)

The gauge pin, single 11.67 mm, designed for precise end‑dimension inspection and routine go/no‑go checks in workshop and production environments

• Workshop version for robust daily use
• Diameter 11.67 mm for tight tolerances
• Accuracy ±0.002 mm for precise checks
• Delivered in protective transport case

Consistent, micrometre‑class measurement for production control

A compact inspection element with ±0.002 mm nominal accuracy provides reproducible results for short‑run checks and fixture setup. The small diameter of 11.67 mm ensures tight fit‑control for bore and end‑dimension verification, reducing the need for corrective rework and speeding up quality checks. Designed as a single‑piece inspection item, this pin performs reliably when used for end‑face and plug‑type assessments, offering a measurable improvement in process stability and traceability.

Robust workshop design that endures everyday handling

Constructed from special steel and specified as a workshop version, the pin withstands standard handling and supports long service intervals. The 50 mm shaft length provides sufficient engagement for most end‑dimension tasks while remaining easy to insert and remove from fixtures; the modest mass (approx. 0.1 kg) aids quick manual handling without sacrificing rigidity. Supplied in a protective case for transport, the item arrives ready for storage and safe transit between job sites.

Practical use cases and benefits for production workflows

Suitable for fixture checking, alignment, go/no‑go applications and dimensional reference tasks, this gauge pin integrates seamlessly into workshop metrology routines. The compact geometry minimises measurement uncertainty from misalignment, and the high tolerance rating supports consistent pass/fail decisions on the shopfloor. Where repeatability matters, the pin acts as a simple, low‑complexity control that complements digital or analogue measuring systems and speeds up setup and inspection cycles.

For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge (Emmerich) at info@metav-werkzeuge.com or +49 2822 7131930 for supply and technical advice on this Metav IndustryLine gauge pin (SKU M323.B67)

Technical data

• • SKU: M323.B67
• • GTIN: 4061905063701
• • Brand: Metav IndustryLine

Facts

• • Diameter: 11.67 mm
• • Length: 50 mm
• • Accuracy / tolerance: ±0.002 mm
• • Weight: 0.1 kg

Special features

• • Material: special steel
• • Workshop version
• • Supplied in protective plastic or wooden transport case
• • Single gauge pin, intended for end‑dimension and go/no‑go checks

FAQ

What is the measuring tolerance of this gauge pin?
The gauge pin (Metav IndustryLine, SKU M323.B67) is specified with a tolerance of ±0.002 mm, making it suitable for high‑precision end‑dimension checks.

Which applications are appropriate for this inspection pin?
This Metav IndustryLine gauge pin is intended for end‑face verification, fixture set‑up, bore checks and go/no‑go testing in workshop and production metrology.

What material and finish does the pin have?
The pin is made from special steel in a workshop‑grade finish to resist routine handling and provide sustained measurement integrity.

Is the gauge pin delivered ready for transport and storage?
Yes. The item is supplied in a protective plastic or wooden transport case to secure the pin during transit.

Can this pin be used for fixture alignment and setting tasks?
Yes. The compact diameter and tight tolerance make the pin suitable for precise alignment and reference tasks within assembly and quality control processes.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com