12.37mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine

Benefit from a combination of repeatable dimensional control and workshop durability: the precision 12.37 mm diameter gauge with ±0.002 mm tolerance and a compact 50 mm length supports reliable end‑measurements and fixture checks. Order the test pin directly via Metav Werkzeuge or consult the Metav advisors for specification support.

Test pin M323.C37 — 12.37 mm diameter, 50 mm length (Metav IndustryLine)

A Test pin M323.C37 designed for precise end‑measurement and locating tasks in workshop metrology and fixture verification

• 12.37 mm precision diameter
• 50 mm length for compact measurement
• ±0.002 mm dimensional tolerance
• Made from special steel for durability

Reduced rework through measurable accuracy

The compact gauge pin delivers 12.37 mm nominal diameter with a guaranteed ±0.002 mm dimensional deviation, making it suitable where tight repeatability is required. The small form factor and high tolerance reduce the risk of misalignment during locating and end‑stop checks, which in turn lowers the frequency of rework and inspection cycles. The special steel construction provides dimensional stability under normal workshop conditions while maintaining the fine surface finish necessary for consistent contact points.

Workshop‑grade design for fixture and gauge use

Built as a workshop‑grade item, this compact probe prioritises handling and robustness without sacrificing metrological intent. At 50 mm overall length the component is easy to manoeuvre in tight jigs and fixturing, while the balanced mass allows controlled placement during manual inspection. The shaft geometry is optimised for repeatable seating in bores or against datum faces, so the gauge pin performs reliably in locating, reference and pass/fail checks common in production and maintenance environments.

Practical integration into quality workflows

The single‑piece supply makes inventory management straightforward and ensures a defined reference per check point. Specification data such as Diameter: 12.37 mm, Length: 50 mm and Tolerance: ±0.002 mm are easily cross‑checked against inspection plans or master drawings. For shops seeking to harmonise measuring practises, the gauge pin is a compact addition to modular inspection sets and bench stations, supporting faster decision cycles and clearer conforming/non‑conforming outcomes.

Contact Metav Werkzeuge for tailored advice on specifying the M323.C37 test pin and to confirm suitability for your fixture or inspection plan

Technical data

• Article number: M323.C37
• GTIN: 4061905066085
• Label: Test pin, single, 12.37 mm length 50 mm
• Manufacturer: Metav IndustryLine
• Material: Special steel
• Length: 50 mm
• Diameter: 12.37 mm
• Weight: 0.1 kg
• Dimensional tolerance: ±0.002 mm
• Special feature: Workshop execution

Core data

• Diameter: 12.37 mm
• Length: 50 mm
• Weight: 0.1 kg
• Tolerance: ±0.002 mm

Special features

• Workshop‑grade execution
• Material: special steel
• Supplied as single piece
• SKU: M323.C37

FAQ

What is the exact diameter of the gauge pin?
The M323.C37 test pin has a nominal diameter of 12.37 mm, specified for precision locating and end‑measurement tasks.

What tolerance can be expected from this test pin?
The test pin is produced to a dimensional deviation of ±0.002 mm, suitable for fine metrology checks in workshop environments.

What material is the pin made from and why does it matter?
Manufactured from special steel, the pin offers good dimensional stability and wear resistance, ensuring consistent contact behaviour during repeated inspections.

Is the pin suitable for fixture verification and locating?
Yes, the compact 50 mm length and the tight tolerance make the M323.C37 appropriate for fixture checks, reference seating and pass/fail gauging in machining and maintenance settings.

How is the product supplied and identified?
The item is supplied as a single test pin under SKU M323.C37 and GTIN 4061905066085, allowing straightforward traceability within inspection inventories.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com