13.32mm Go/No-Go Gauge Pin 50mm Workshop Version, Special Steel - Metav IndustryLine

Benefit from the combination of a 13.32 mm diameter, ±0.002 mm accuracy and robust special steel construction for consistent inspection results; the compact 50 mm length supports safe handling in fixtures and gauges. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed.

Gauge pin M323.D32 — single precision test pin, 13.32 mm diameter, 50 mm length (Metav IndustryLine)

The Gauge pin M323.D32 is a single precision test pin designed for end‑measure checks and workshop inspection tasks where repeatable diameter reference and compact handling are required.

• Precision diameter 13.32 mm, ±0.002 accuracy
• Short 50 mm length for secure fixture handling
• Special steel for long wear resistance
• Delivered in a protective box for transport

Reduce rework with measurable precision

A consistent production flow depends on measurable, repeatable checks. The gauge pin provides a 13.32 mm reference diameter with a verified ±0.002 mm deviation, which translates into reliable pass/fail verification at assembly or inspection stations. This level of control reduces rework and scrap by tightening the dimensional gate early in process chains. The calculation of tolerances and the narrow accuracy band support efficient quality decisions and fewer stoppages during serial checks.

Robust construction for everyday workshop use

Constructed from special steel, the pin resists wear and maintains dimensional integrity under frequent insertion and withdrawal cycles. The workshop‑grade finish and material selection minimise surface damage that can bias measurements over time. As a result, maintenance intervals are extended and replacement costs are reduced — a practical advantage for production environments where tools are used continuously and downtime carries a measurable cost.

Compact format that fits tight assemblies

With a length of 50 mm, the test pin offers safe handling in confined fixturing and gauge housings without excess overhang. The short form factor improves accessibility to end faces and bores in compact components, while retaining sufficient mass for steady handling. This balance between reach and rigidity benefits measurement technicians who require a stable datum in tight assemblies and in-process inspection jigs.

Protected delivery for transport and workshop logistics

The article is supplied in a protective box suitable for transport, reducing the risk of accidental knocks or corrosion during storage or transit; the packaging is primarily intended to safeguard the tool rather than for permanent storage. Robust packaging supports reliable logistics and ensures the pin reaches the bench ready for immediate use, preserving the factory calibration and surface condition expected for precision inspection tools.

Practical application and integration in inspection routines

The gauge pin serves as a straightforward reference for go/no‑go checks, comparator setups and quick end‑measure verification in a wide range of workshop and inspection workflows. Its compact dimensions and tight tolerance make it suitable for routine quality control in metalworking and assembly processes. For operations seeking standardised reference artefacts, this test pin integrates easily into existing gauge sets and fixture designs.

Contact Metav Werkzeuge to discuss how the Metav IndustryLine gauge pin M323.D32 with a 13.32 mm diameter and ±0.002 mm accuracy fits into inspection workflows, or to place an order by phone (+49 2822 7131930) or e‑mail (info@metav-werkzeuge.com)

Technical data

• Article number: M323.D32
• GTIN: 4061905067938
• Manufacturer: Metav IndustryLine
• Label: Gauge pin, single, 13.32 mm diameter, length 50 mm

Facts

• Diameter: 13.32 mm
• Length: 50 mm
• Weight: 0.1 kg
• Accuracy / tolerance: ±0.002 mm
• Category: Gauge pins (Messstifte)

Special features

• Material: special steel
• Workshop execution (Werkstatt‑Ausführung)
• Supplied in a protective box for transport
• Single test pin for end‑measure checks
• Compact format for tight fixtures

FAQ

What is the declared tolerance of this gauge pin?
The gauge pin M323.D32 is specified with a tolerance of ±0.002 mm, which defines the acceptable deviation from the nominal 13.32 mm diameter for inspection tasks.

Is the pin suitable for repeated use in production checks?
Yes, the special steel construction and workshop design make the test pin suitable for frequent insertion and withdrawal cycles common in production verification.

Can the pin be used as a reference in comparator fixtures?
The compact 50 mm length and stable diameter make the pin appropriate as a reference element in comparator setups and custom fixture applications.

How does the protective box affect storage?
The protective box is supplied to safeguard the pin during transport and handling; it offers short‑term protection but is not recommended as the primary long‑term storage solution for precision artefacts.

Which industries or applications benefit most from this gauge pin?
The pin is well suited to metalworking inspections, assembly line end‑measure checks and small‑part verification where a high‑precision diameter reference is required; it integrates easily with standard gauge sets and fixtures.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com