13.56mm Test Pin Length 50mm Workshop Version - Metav IndustryLine

Precise, compact and workshop‑graded: the combination of ±0.002 mm tolerance, 13.56 mm diameter and 50 mm length provides a reliable reference for end‑dimension verification and fixture alignment; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice.

Test pin, single, 13.56 mm diameter, length 50 mm (M323.D56)

The Test pin, single, 13.56 mm, length 50 mm (M323.D56) serves as a precision gauge pin for end‑measure verification, alignment and plug‑gauge tasks in workshop and inspection environments

• Precision ±0.002 mm tolerance
• Diameter 13.56 mm for end‑measure checks
• 50 mm overall length for compact fixtures
• Workshop version in special steel

Engineered for dependable end‑dimension verification

The gauge pin is produced to a tight ±0.002 mm manufacturing tolerance, making it suitable as a reference element in repetitive inspection tasks where reproducible results are required. With a nominal diameter of 13.56 mm, the pin functions as a standardised plug for checking final dimensions and seating in bores or sockets; the narrow tolerance reduces the risk of false rejects and supports faster decision cycles on the shop floor. The construction emphasises dimensional accuracy and consistent repeatability rather than decorative finishes, which benefits quality control routines and process stability.

Compact design that suits fixtures and inspection rigs

At 50 mm overall length and weighing approximately 0.1 kg, the component offers a low‑profile solution for confined set‑ups and fixture blocks. The special steel composition grants mechanical robustness under frequent insertion and removal, while the short form factor helps maintain alignment integrity in tight assemblies. This compact, workshop‑grade configuration simplifies handling and reduces set‑up time compared with longer or heavier reference pins, so throughput in small‑batch inspection and jigs is improved without compromising measurement certainty.

Reliable integration into production and measurement workflows

Designed for straightforward use in end‑measure control, the pin complements common plug‑gauge and alignment procedures; it is appropriate for controlled checks during assembly, final inspection and part acceptance. The production tolerance and simple geometry make the element compatible with established metrology equipment and manual verification steps, providing a clear pass/fail reference or a repeatable datum. The workshop specification supports frequent, practical use where traceable results and limited handling complexity are priorities.

Contact Metav Werkzeuge for ordering details or application support for the Metav IndustryLine test pin M323.D56 with 13.56 mm diameter and ±0.002 mm precision and ensure the correct reference parts are supplied for the inspection task at hand

Technical Data

• Article number: M323.D56
• GTIN: 4061905067068
• Label: Test pin, single, 13.56 mm, length 50 mm

Facts

• Diameter: 13.56 mm
• Length: 50 mm
• Tolerance: ±0.002 mm
• Weight: 0.1 kg
• Material: Special steel

Special features

• Workshop version
• Suitable for end‑dimension verification
• Compact form for fixture integration

FAQ

What tolerance does this gauge pin provide and what does it mean for inspection?
The test pin is manufactured to a ±0.002 mm tolerance; this level of precision delivers a stable reference point for end‑dimension checks and reduces measurement variability in routine inspection workflows with the Metav IndustryLine M323.D56 test pin.

Is the material suitable for frequent use in a workshop environment?
Yes, the M323.D56 is made from special steel and specified as a workshop version, giving mechanical resilience for repeated insertion and handling in fixtures and measurement set‑ups.

Can this pin be used as a plug gauge for bore verification?
The 13.56 mm diameter and tight tolerance make the pin appropriate as a plug‑type reference for bore seating and end‑measure verification within compatible inspection procedures.

Does the product come with traceability or calibration documentation?
The product data does not indicate supplied calibration certificates; any calibration or traceability requirements should be confirmed with Metav Werkzeuge prior to purchase to ensure alignment with specific quality system needs.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com