13.97mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine

Take advantage of a compact, workshop-ready gage that combines a Ø 13.97 mm nominal diameter with a repeatable ±0.002 mm tolerance and a 50 mm length for fast end‑dimension checks; its special steel construction ensures durability in daily use. Order the inspection pin directly via Metav Werkzeuge or ask our consultants if needed.

Inspection pin M323.D97 – Ø 13.97 mm, 50 mm length (Metav IndustryLine)

The Inspection pin M323.D97 is a precision gage pin designed for end‑dimension verification and quick in‑process checks in workshop environments.

*Workshop version, robust design
*Diameter 13.97 mm, high-precision fit
*Tolerance ±0.002 mm for reliable checks

Consistent end‑dimension checks for assembly and inspection

This gage pin delivers a compact solution for routine dimensional control where tight fits and repeatable results matter. The combination of Ø 13.97 mm and a 50 mm overall length gives a stable bearing surface that reduces wobble during insertion, while the declared ±0.002 mm variation supports trustworthy go/no‑go assessments in production. The use of special steel balances surface hardness with resistance to wear, preserving the pin’s geometry through repeated handling and contributing to lower rejection rates on assembly lines.

Built for workshop handling and everyday robustness

The workshop version construction provides resilience against knocks and frequent manipulation typical in trade and maintenance contexts. At approximately 0.1 kg, the pin is heavy enough to feel substantial in hand yet compact for rapid gauging tasks; that mass aids stable seating in bores and sockets without being cumbersome. The refined shaft finish and precision fit make it suitable for use in jigs, fixture checks and as a reference in quick go/no‑go procedures where simplicity and repeatability save time on the shop floor.

Integrates smoothly into quality routines and tooling sets

Designed to complement existing gage sets and bench tooling, this inspection pin supports efficient process control and reduces setup iteration. The straightforward geometry eases use in line inspections, bore verification and end‑dimension confirmation of machined parts. By standardising on a reliable, workshop‑orientated pin, teams can improve throughput and consistency without complex calibration steps; the short, rigid profile is especially beneficial for final dimensional checks and fastening alignment tasks.

Contact Metav Werkzeuge for tailored advice on incorporating this inspection pin into workshop inspection processes; Metav Werkzeuge in Emmerich can supply the M323.D97 and advise on compatible tooling and delivery options – info@metav-werkzeuge.com | +49 2822 7131930

Technical data

• Article number: M323.D97
• GTIN: 4061905067631
• Description: Inspection pin, single, Ø 13.97 mm, length 50 mm

Facts

• Diameter: 13.97 mm
• Length: 50 mm
• Weight: 0.1 kg
• Tolerance / variation: ±0.002 mm

Special features

• Material: special steel
• Workshop version
• Intended for end‑dimension checks and bore verification

FAQ

What applications suit this inspection pin best?
The inspection pin M323.D97 is intended for end‑dimension checks, bore verification and simple go/no‑go assessments in workshop and production environments.

How precise is the pin for repeatable measurements?
Manufactured for a variation of ±0.002 mm, the pin delivers repeatable seating and reliable pass/fail decisions for typical assembly and inspection tasks.

Which material is used and how does it affect durability?
Made from special steel, the pin offers a durable surface and wear resistance suitable for frequent workshop use without rapid deterioration of the reference diameter.

Can this pin be used in jigs and fixture alignment?
Yes; the compact 50 mm length and rigid profile are designed to assist with alignment, seating checks and fixture verification during setup and production runs.

Is the pin suitable for precision laboratory metrology?
While optimised as a workshop gage, the pin’s tight tolerance makes it useful for routine quality control; for lab‑grade traceability and submicron requirements, a dedicated laboratory standard should be considered

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com