14.28mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine

Take advantage of the combination of precise diameter control (14.28 mm), high dimensional accuracy (±0.002 mm) and robust special steel to standardise end‑dimension checks in production and inspection. Order the pin directly via Metav Werkzeuge or consult our specialists for integration advice.

Gage pin, single, 14.28 mm, length 50 mm — workshop reference pin with ±0.002 mm accuracy

The Gage pin, single, 14.28 mm, length 50 mm is a compact inspection pin designed for repeatable end‑dimension verification, fixture setup and reference checks in workshop and shop‑floor metrology.

• Precision diameter 14.28 mm ±0.002 mm
• Length 50 mm for end‑dimension checks
• Made from special steel for robustness
• Delivered in a transport case

Reproducible end‑dimension checks for quality control

A purpose‑made gage pin with a defined diameter of 14.28 mm and an accuracy of ±0.002 mm provides a stable reference when verifying component end faces or mating bores. The tight tolerance reduces measurement uncertainty and shortens inspection loops, which helps to lower scrap rates and speeds up pass/fail decisions. Used as a master reference in routine checks or as a plug gauge substitute, this pin supports a consistent inspection workflow and improves overall process reliability.

Dimensional stability and workshop suitability

Manufactured from special steel, the pin combines wear resistance with dimensional stability under typical workshop conditions. The 50 mm length gives sufficient engagement for end‑face and short‑bore verifications while remaining easy to handle. The workshop execution ensures the component withstands everyday mechanical demands; its mass and surface finish contribute to repeatable seating in fixtures and gauges. A compact reference of this kind is particularly useful where space is limited but traceable precision is required.

Practical handling, storage and integration in inspection routines

The pin is supplied ready for use and stored safely in a transport case, which protects the calibrated diameter and surface during handling and transport. Lightweight and simple to incorporate, the reference pin suits hand inspection, fixture alignment and gauge setting tasks without adding complexity to the measurement procedure. For workshops seeking to centralise precision tools, this single‑piece reference integrates directly into go/no‑go checks and short‑run quality procedures, offering a pragmatic balance between robustness and metrological performance.

Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gage pin M323.E28 can be integrated into your inspection process or to request ordering guidance

Technical data

• Article number: M323.E28
• GTIN: 4061905069680
• Label: Gage pin, single, 14.28 mm, length 50 mm

Facts

• Diameter: 14.28 mm
• Length: 50 mm
• Accuracy: ±0.002 mm
• Weight: 0.1 kg

Special features

• Material: Special steel
• Version: Workshop execution
• Delivery: transport case included
• Suitable for end‑dimension and fixture checks

FAQ

What is the nominal diameter and tolerance of this gage pin?
The gage pin has a nominal diameter of 14.28 mm with an indicated tolerance of ±0.002 mm for high‑precision reference measurements.

Can the gage pin be used for fixture alignment and gauge setting?
Yes; the M323.E28 gage pin is designed as a compact inspection reference suitable for fixture alignment, short‑bore checks and gauge setting on the shop floor.

What material is the pin made from and why does it matter?
The inspection pin is made from special steel, which provides wear resistance and dimensional stability important for repeatable seating and long‑term accuracy.

Is the pin supplied ready for safe storage and transport?
The pin is supplied in a protective transport case to maintain the integrity of the calibrated diameter and to prevent damage during handling.

How does this reference pin support routine quality control?
By offering a defined diameter and tight tolerance, the reference pin standardises end‑dimension checks, shortens inspection cycles and improves repeatability in routine quality processes.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com