16.16mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine

Combining workshop-grade construction, a precise 16.16 mm diameter and a tight ±0.002 mm tolerance, this gauge pin provides reliable end‑measurement performance for routine inspection tasks; order directly via Metav Werkzeuge or contact our consultants for application advice.

Gauge pin, single — 16.16 mm Ø, 50 mm length (Metav IndustryLine)

The gauge pin M323.G16 is a single, workshop‑grade measuring pin designed for precise end‑measurements and fit checks in small to medium mechanical assemblies.

• Workshop-grade design for robust use
• Diameter 16.16 mm for exact gauge fits
• Length 50 mm for standard end‑measurement
• Tolerance ±0.002 mm for high repeatability

Precision that supports consistent production

This single gauge pin is engineered for repeatable end‑measurements, with a nominal diameter of 16.16 mm and a verified tolerance of ±0.002 mm, ensuring consistent results when checking bores, dowel fits or mating components. The compact 50 mm shaft length minimises deflection during clamping and measuring, which reduces measurement scatter and shortens inspection cycles. The special steel construction contributes to wear resistance and dimensional stability under normal workshop conditions.

Ideal for micro‑range inspection and fine mechanical work

Classified within the micro measurement range, the pin suits small, high‑precision checks where short shanks and low torsion are essential. The M323.G16 functions as a reliable go/no‑go reference for assembly verification and quality control in toolrooms, small‑batch production and maintenance workshops. Because the geometry is focused on exact fits rather than long‑reach measurement, operators benefit from easier handling and faster repeat checks without complex fixturing.

Built for the workshop: handling, storage and longevity

Delivered as a single workshop version pin, the item is tailored for everyday use rather than laboratory calibration. The workshop‑grade finish balances robustness with the surface quality needed for fit tests, while the included transport case protects the pin during transit and storage. Regular cleaning and light lubrication of contact surfaces will maintain performance; the moderate mass and compact dimensions also make the pin straightforward to position by hand or in simple fixtures, accelerating routine inspection workflows.

Contact Metav Werkzeuge for tailored advice or to request this Metav IndustryLine gauge pin for your inspection bench — our specialists in Emmerich can help confirm fit and handling requirements

Technical data

• SKU: M323.G16
• GTIN: 4061905068126
• Material: Special steel
• Diameter: 16.16 mm
• Length: 50 mm
• Tolerance: ±0.002 mm
• Weight: 0.15 kg
• Workshop execution

Facts

• Nominal diameter: 16.16 mm
• Shaft length: 50 mm
• Accuracy: ±0.002 mm
• Weight (approx.): 0.15 kg

Special features

• Delivered in transport case for safe handling
• Category: Gauge pins (Messstifte)
• Story trigger: end measurements

FAQ

What is the primary use of this gauge pin?
The gauge pin M323.G16 is intended for end‑measurements and fit checks of bores and dowel seats in workshop and inspection settings.

Is the material corrosion‑resistant?
The pin is made from special steel, offering good wear resistance for typical workshop use; specific corrosion resistance is not declared.

Can this pin be used as a reference for precision gauging?
With a tolerance of ±0.002 mm, the pin is suitable for repeatable workshop checks and fit verification; for laboratory reference standards, calibrated artefacts should be considered.

Does the delivery include protective packaging?
Yes, the item is supplied with a transport case to protect the pin during shipment and storage.

What inspection tasks are best suited to this diameter and length?
The 16.16 mm diameter and 50 mm length are ideal for small to medium bores, assembly fit verification and routine bench checks where short shanks reduce deflection.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com