16.98mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine

Take advantage of the combination of workshop-grade construction, ±0.002 mm dimensional accuracy and a compact 50 mm length for reliable end‑dimension checks; order the test pin directly via Metav Werkzeuge or consult the Metav team for application advice.

Test pin M323.G98 — single control pin, Ø 16.98 mm, 50 mm length, Metav IndustryLine

The Test pin M323.G98 is a workshop-grade control pin for precise end‑dimension verification and fixture reference in production and inspection environments

• Workshop-grade design
• Nominal diameter Ø 16.98 mm
• 50 mm overall length
• Dimensional tolerance ±0.002 mm
• Delivered in protective case

Precision where tolerances count

The M323.G98 control pin delivers high reproducibility through a tight dimensional specification of ±0.002 mm, making it suitable for fine inspection tasks and go/no‑go checks in shopfloor environments. With a nominal diameter of 16.98 mm, the pin provides a defined reference surface for comparative measurements and repeatable alignment in jigs and fixtures. The specified tolerance is a technical guarantee that supports quality control regimes and helps reduce scrap rates by ensuring that critical fits are evaluated against a stable reference.

Robust workshop construction for daily use

Manufactured in special steel, this workshop version is designed for handling and routine use rather than delicate laboratory duty; the material choice balances wear resistance and dimensional stability. The compact 50 mm overall length and modest mass (approx. 0.15 kg) ease handling and positioning in confined setups, while the supply in a protective case minimises transport damage and protects measuring faces between uses. These attributes contribute to longer service life and fewer unplanned replacements, increasing uptime on the production line.

Practical benefits in inspection and assembly

As a single control pin for end‑dimension and reference measurements, the component integrates into assembly verification steps, fixture set‑up and finish inspection. The clear nominal size of 16.98 mm simplifies documentation and traceability when recording results, and the pin’s compact form factor supports rapid swap‑out during batch changeovers. Where reproducible contact points are required, this workshop pin acts as a dependable mechanical datum, helping technicians maintain consistent assembly tolerances with straightforward handling.

Choose the Metav IndustryLine M323.G98 when repeatable, workshop‑proven reference gauges are required — contact Metav Werkzeuge for tailored ordering and application guidance via info@metav-werkzeuge.com or by phone at +49 2822 7131930

Technical Data

• Article number: M323.G98
• GTIN: 4061905071355
• Manufacturer: Metav IndustryLine

Facts

• Nominal diameter: 16.98 mm
• Overall length: 50 mm
• Dimensional tolerance: ±0.002 mm
• Weight: 0.15 kg

Special features

• Material: special steel
• Workshop execution
• Delivered in protective case
• Category: test pin

FAQ

What level of accuracy does the test pin provide?
The test pin M323.G98 is specified with a dimensional tolerance of ±0.002 mm, suitable for precise shopfloor checks and comparative inspections where tight repeatability is required.

What material is used for the control pin?
The pin is made from special steel, chosen for mechanical robustness and dimensional stability in workshop conditions.

Is the test pin supplied with protective packaging?
Yes, the M323.G98 is supplied in a protective case to reduce handling damage during transport and storage.

For which tasks is this control pin most suitable?
This single test pin is designed for end‑dimension verification, fixture referencing and go/no‑go checks in production and inspection workflows.

How should the pin be referenced in documentation and traceability records?
Record the nominal diameter 16.98 mm, the article number M323.G98 and the stated tolerance ±0.002 mm to ensure clear traceability in quality records.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com