18.46mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine

Reliable workshop performance meets fine traceability: the compact design and dimensional tolerance ±0.002 mm ensure consistent end‑measure checks across production runs. Combine robust construction, exact fit and straightforward procurement via Metav Werkzeuge for dependable gauging; order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support.

Gauge pin M323.I46 – single test pin, Ø 18.46 mm, 50 mm length (Metav IndustryLine)

The Gauge pin M323.I46 is a compact test pin intended for end‑measure verification and inspection tasks in workshop and production environments, offering a dedicated solution where repeatable small‑scale gauging is required.

• Workshop-grade construction
• Diameter 18.46 mm for end‑measure checks
• Length 50 mm hardened special steel
• Dimensional tolerance ±0.002 mm

Repeatable results through defined tolerance and fit

The pin's dimensional tolerance of ±0.002 mm provides a clear technical basis for repeatable measurements and pass/fail decisions on small features. In practical terms, this level of accuracy reduces ambiguity when verifying end dimensions or checking fits during incoming‑goods inspection, so production control data remain consistent. The specification is suitable for routine gauging where narrow tolerance windows are enforced and where measurement uncertainty must be minimised to maintain product conformity.

Robust, workshop‑grade design for everyday handling

Built as a workshop‑execution test pin from special steel, the component resists the handling and contact stresses typical of daily inspection routines. The compact mass and balanced geometry support secure placement and stable seating in fixtures or test rigs, while the manageable weight assists quick handling on the shop floor. These attributes translate into fewer setup adjustments and a lower rate of incidental surface damage during repetitive checks, which helps preserve measurement integrity over time.

Compact dimensions that suit confined checks

The combination of a 50 mm length and a 18.46 mm diameter makes this pin particularly useful for confined spaces, short bore inspections and end‑measure applications where longer gauges would be impractical. Its dimensions allow it to serve as a reference mandrel for small assemblies and to be used in pneumatic or manual test fixtures where accessibility is limited. This compact form factor supports efficient gauging cycles without compromising on the contact area needed for stable measurement.

Clear identification and workflow integration

Marked and catalogued for procurement workflows, the test pin is supplied as a single unit and is easily referenced in bills of material and inspection plans. The inclusion of an article identifier and GTIN supports traceable ordering and inventory control, while sourcing from Metav IndustryLine benefits from the company's European quality‑filter approach and broad product availability. This alignment between specification, identification and supply chain reduces lead times and simplifies repeat orders for production and maintenance schedules.

Request technical sheets or a tailored supply proposal from Metav Werkzeuge for the Metav IndustryLine gauge pin M323.I46; contact info@metav-werkzeuge.com or call +49 2822 7131930 for application advice and assured delivery from Emmerich.

Technical data

• Article number: M323.I46
• SKU: M323.I46
• GTIN: 4061905072772
• Manufacturer: Metav IndustryLine

Facts

• Diameter: 18.46 mm
• Length: 50 mm
• Tolerance: ±0.002 mm
• Weight: 0.15 kg

Special features

• Workshop version
• Single gauge pin for end‑measures
• Material: Special steel
• Category: Gauge pins

FAQ

What is the intended use for this test pin?
The gauge pin M323.I46 is intended for end‑measure checks and small‑bore verification in workshop and production inspection tasks.

How precise is the dimensioning of the pin?
The pin is manufactured to a tolerance of ±0.002 mm, providing tight repeatability suited to routine gauging and quality control.

Which material is used for the pin?
The test pin is made from special steel, selected for workshop durability and stable contact performance.

Can the pin be ordered individually for replacement stocks?
Yes, the item is supplied as a single unit under SKU M323.I46 and can be re‑ordered via Metav IndustryLine channels.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com