18.72mm Test Pin 50mm Length Workshop Finish - Metav IndustryLine

Take advantage of the combination of workshop‑hardened construction, ±0.002 mm tolerance and compact dimensions for reliable end‑measurement checks; order directly via Metav Werkzeuge or consult our specialists for application advice.

Gauge pin M323.I72 — Precision gauge pin, 18.72 mm Ø, 50 mm length (Metav IndustryLine)

A gauge pin M323.I72 engineered for accurate end‑measure verification and repeatable inspection tasks in workshop and quality‑control environments.

• Workshop version, robust construction
• Diameter 18.72 mm for end‑measure checks
• Tolerance ±0.002 mm for high repeatability
• Protective transport case included

Accuracy that removes doubt from inspection

The central technical advantage is the ±0.002 mm tolerance, which positions this gauge pin in the high‑precision segment for routine workshop inspections. Such a narrow deviation ensures repeatable end‑of‑shaft measurements and dependable reference checks during set‑up or final inspection. The specified accuracy minimises rework and supports consistent quality decisions in production and maintenance processes.

Built for the workshop — durable and dependable

Made from special steel and released as a workshop version, the pin withstands daily handling and moderate impacts typical in machine shops. The material choice balances hardness with toughness to preserve the measuring surface while resisting wear. Robust construction reduces the need for frequent replacement, ensuring stable measurement results over the part’s service life and saving time on recalibration cycles.

Compact form factor for tight fixtures and assemblies

With a diameter of 18.72 mm and a length of 50 mm, this precision pin suits confined measuring points and end‑dimension checks where access is limited. Classified within the micro range for calipers and pins (measurement ranges from 10–100 mm), the design combines adequate reach with low bending risk, enabling controlled, repeatable contact even in small jigs and fixtures.

Practical handling and traceable delivery

Supplied as a single, individually identified gauge pin, the item arrives ready for immediate use in inspection routines. Delivery includes a protective transport case to prevent surface damage during storage and transit, aiding traceability and preserving the calibrated surface finish. The compact mass and neat form factor make handling straightforward on the shop floor and simplify tool storage between measurement cycles.

Contact Metav Werkzeuge for tailored advice on integrating the M323.I72 into inspection routines or to arrange immediate supply from our Emmerich stock

Technical Data

• SKU: M323.I72
• GTIN: 4061905072420
• Manufacturer: Metav IndustryLine
• Weight: 0.15 kg
• Material: Special steel
• Length: 50 mm
• Diameter: 18.72 mm
• Tolerance / Accuracy: ±0.002 mm
• Label: Gauge pin, single, 18.72 mm diameter, 50 mm length
• Story trigger: end dimensions

Facts

• Measurement range max: 18.72 mm
• Measurement range min: 18.72 mm
• Measurement resolution hundredths: 2
• Measurement range tenths: 7

Special features

• Workshop design
• Delivered as single pin
• Protective transport case for transport and storage
• Ideal for end‑measure verification and inspection tasks

FAQ

What is the intended use of this gauge pin?
This gauge pin is intended for end‑measurement verification and routine inspection tasks; the M323.I72 from Metav IndustryLine serves as a stable reference for end‑dimension checks.

How precise is the measurement capability?
The M323.I72 offers a tolerance of ±0.002 mm, providing high repeatability for shop‑floor inspection and set‑up verification.

Which materials is the pin suited to measure or check?
The pin is a dimensional reference rather than a cutting tool; it is suitable for gauging components made of metals and assemblies where an 18.72 mm reference diameter is required.

Is the pin delivered ready for use and protected in transit?
The gauge pin is supplied individually and comes in a protective transport case to preserve the measuring surface and simplify storage.

Can the M323.I72 be used in tight fixtures and jigs?
Yes; the compact 50 mm length and precise 18.72 mm diameter make it well suited to confined fixtures and end‑face measurements.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com