0.75-400mm Ultrasonic Thickness Gauge Adjustable Sound Velocity 1,000–9,999m/s, USB Bluetooth, Case - Metav IndustryLine

Take advantage of wide measurement capability and a 5 MHz transducer for reliable readings across thin and thick materials, combined with a compact 10 mm probe tip and an approx. 1 m cable for easy access in confined areas; order the probe directly via Metav Werkzeuge or ask our consultants if needed. Probe for ultrasonic thickness gauge 0.75–400 mm, straight (5 MHz, Ø10 mm) — Metav IndustryLine A probe for ultrasonic thickness gauges 0.75–400 mm designed as a straight transducer for general-purpose thickness inspection in workshops and production lines. 5 MHz centre frequency Measurement range 0.75–400 mm Ø10 mm probe diameter Cable length approx. 1 m Broad measurement range that balances penetration and resolution The transducer covers a 0.75–400 mm thickness window, allowing measurements from thin coatings and sheet metal up to substantial plate thicknesses without frequent probe changes. The 5 MHz frequency offers a practical compromise between penetration depth and axial resolution: it improves detection on thicker or corroded components while still resolving interfaces in thinner materials. For engineers and quality technicians, this balance reduces the need for multiple probes and streamlines inspection routines, saving setup time and lowering complexity in routine thickness control. Compact, straight design for confined and standard access points A Ø10 mm tip and a straight design make the sensor ideal where access is limited or where small radii require a slim contact area. The approximately 1 m cable provides freedom of movement at the inspection site while keeping the transducer close to measurement equipment. The robust construction suits workshop environments and frequent handling; the small probe face also helps avoid excessive dead‑zone effects on thin samples, enhancing repeatability when measuring small parts or recessed surfaces. Ease of integration and dependable identification for inventory control The probe is supplied with clear identifiers (SKU M502.411, GTIN 4054469162546) to simplify stock management and traceability. Weight and mechanical dimensions support predictable handling and fixture mounting. As a Metav IndustryLine component, the sensor benefits from the distributor’s emphasis on accessibility and dependable supply: straightforward part identification and consistent availability assist procurement and maintenance planning in production environments. These factors contribute to reduced downtime and more predictable inspection workflows. Contact Metav Werkzeuge for a tailored compatibility check and delivery information for the Metav IndustryLine probe M502.411 — expert advice and stock proximity from Emmerich reduce lead times and ensure correct instrument matching Technical data Article number: M502.411 GTIN: 4054469162546 Tariff number: 90179000 Core technical data Measurement range: 0.75–400 mm Frequency: 5 MHz Probe diameter: 10 mm Cable length: approx. 1 m Weight: 2 kg Features and compatibility Straight transducer design Connector: 13 Type: straight Category: Ultrasonic thickness gauge probe FAQ What thickness range can be measured with this probe? The Metav IndustryLine probe M502.411 measures thicknesses from 0.75 mm up to 400 mm, covering both thin sheets and thicker plates. What operating frequency does the transducer use? The probe operates at 5 MHz, a frequency selected to balance penetration on thicker materials with adequate resolution on thinner samples. Is the probe suitable for confined or recessed measurement points? Yes, the Ø10 mm probe tip and straight form factor are designed to access small or recessed areas where larger faces would not fit. How is the probe identified for inventory and ordering? Identification is via SKU M502.411 and GTIN 4054469162546 to simplify ordering and stock control. Can the probe be mounted or used with standard ultrasonic thickness gauges? The transducer is intended for use with ultrasonic thickness gauges; the connector specification (13) should be checked against instrument compatibility before integration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact Ø 10 mm active face and a broad measurement range of 0.75–400 mm to inspect thin and thick materials with the same transducer; the 5 MHz frequency balances penetration and resolution for general-purpose thickness testing. Order the probe directly via Metav Werkzeuge or ask our consultants if needed. Probe for Ultrasonic Thickness Gauge M502.412 – 90° angled, 5 MHz, Ø 10 mm (Metav IndustryLine) A Probe for Ultrasonic Thickness Gauge M502.412 engineered for accurate thickness measurement from 0.75 to 400 mm, offering an angled transducer for inspections in confined or offset positions Measurement range 0.75–400 mm 5 MHz for balanced penetration and resolution 90° angled transducer for confined access Ø 10 mm active face, compact footprint Reliable readings across a wide range of materials The angled transducer delivers consistent results across a large thickness span by combining a 5 MHz centre frequency with a compact Ø 10 mm contact face. This frequency provides a practical compromise between signal penetration and resolution, making the instrument suitable for typical workshop and inspection tasks where both thin-sheet and moderate-thickness measurements are required. The specified measurement range 0.75–400 mm enables a single transducer to replace multiple probes, reducing setup time and inventory complexity while maintaining reproducible readings when paired with a compatible ultrasonic thickness meter. Designed for inspections in restricted or angled positions The 90° orientation of the active face facilitates access to edges, recesses and areas where a straight probe cannot be aligned. The compact contact diameter supports focused coupling on small features and weld toes, and the approx. 1 m cable gives flexible reach without excess bulk. Mechanical robustness and a small transducer footprint simplify handling during repeated checks: less repositioning is required, which shortens inspection cycles and lowers the risk of operator-induced variability. This configuration is particularly helpful in fabrication, maintenance and quality control environments where space is limited. Practical compatibility and straightforward operation Calibrated instruments paired with this transducer yield efficient inspection workflows, since the probe’s specification matches common ultrasonic gauges used in industry. The transducer’s geometry and electrical connection are compatible with standard measurement setups, supporting rapid exchange and minimal downtime. Clear, reproducible contact and a compact active face reduce coupling fluid usage on small surfaces. For specialised geometries a note is provided regarding the minimum test-piece geometry >Ø20×3, which should be observed to ensure valid readings on strongly curved or thin sections. Choose the Metav IndustryLine 5 MHz 90° angled probe M502.412 for versatile thickness checks from 0.75–400 mm and contact Metav Werkzeuge in Emmerich for expert advice and reliable supply. Technical data Article number: M502.412 GTIN: 4054469162577 Category: Ultrasonic thickness gauge probe Manufacturer: Metav IndustryLine Facts Measurement range: 0.75–400 mm Frequency: 5 MHz Active diameter: Ø 10 mm Cable length: approx. 1 m Connector: 13 Weight: 2.0 kg Tariff number: 90179000 Special features 90° angled transducer Compact active face for confined access Suitable for thin and moderate-thickness measurements Minimum test-piece geometry >Ø20×3 Cable length approx. 1 m FAQ What thickness range can be measured with this probe? The probe supports thickness measurements between 0.75 mm and 400 mm; the M502.412 is optimised for that full span when used with a compatible ultrasonic thickness gauge. Why is a 5 MHz frequency specified and what does it mean in practice? A 5 MHz centre frequency offers a balance between penetration and resolution; the M502.412 uses this frequency to provide reliable returns on a variety of materials without sacrificing measurement clarity. Is the angled design suitable for weld or edge measurements? Yes, the 90° angled transducer on the M502.412 is intended for access to edges, weld toes and recessed areas where a straight probe would be difficult to position. What is the active contact size and why does it matter? The active face is Ø 10 mm; a smaller contact concentrates the ultrasound for localised checks and helps when measuring small features or when limited coupling area is available. Are there any minimum geometry requirements for valid readings? Measurements on strongly curved or narrow parts should observe the stated minimum test-piece geometry (>Ø20×3) to ensure accurate coupling and repeatable results with the M502.412. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise readings in confined spaces thanks to the combination of an angled 90° head, a 7 MHz centre frequency and a compact Ø 6 mm contact face for reliable thickness control; order directly via Metav Werkzeuge or consult our specialists for application advice. Probe M502.413 — Angled 90° Ultrasonic Thickness Gauge Probe, 7 MHz, Ø 6 mm The Probe M502.413 is an angled ultrasonic transducer designed for fast and reliable wall-thickness measurements on curved or hard-to-reach surfaces, suitable for routine inspection and maintenance. Angled 90° probe head for tight access areas 7 MHz frequency for versatile thickness scanning Measurement range 0.75–80 mm 1 m cable with 8.5 connector Precision in confined or complex geometries The angled 90° head and compact Ø 6 mm contact face enable dependable readings where straight probes cannot reach, for example at weld toes, pipe bends or inside housing recesses. With a measurement range of 0.75–80 mm and a 7 MHz centre frequency, the transducer balances resolution and penetration so that thin coatings and moderate wall thicknesses can be measured without excessive signal loss. This combination reduces the need for repeated set‑ups and shortens inspection cycles, supporting efficient asset monitoring. Practical integration and dependable coupling Equipped with an approximately 1 m cable and an 8.5 connector, the transducer is prepared for straightforward connection to standard ultrasonic thickness gauges. The probe requires conventional couplant and a minimum test area consistent with the specification >Ø15×2, ensuring meaningful sound-path geometry for accurate readings. The compact construction and clear electrical interface help keep instrument setup time to a minimum and simplify transfers between inspection points. Built for routine inspection and maintenance regimes Designed as a workshop-ready inspection accessory, the transducer serves corrosion monitoring, plant maintenance and quality checks where repeatable results matter. The 7 MHz frequency delivers a practical compromise between resolution and penetration for a wide range of ferrous and non-ferrous components, enabling faster decision-making during preventive maintenance and reducing unplanned downtime. The small contact diameter also assists in measuring smaller features without sacrificing signal clarity. Supply reliability and trusted provenance Sourced under the Metav IndustryLine umbrella, this sensor benefits from Metav’s logistics and quality filter for the European market. The compact, application-focused design makes the transducer a straightforward upgrade for service teams that need reliable ultrasonic data without complex integration. Product traceability is supported via its SKU and GTIN for inventory and compliance workflows. For tailored advice on using the Metav IndustryLine probe in specific inspection scenarios or to request ordering guidance from Metav Werkzeuge, please contact our consultants in Emmerich. Technical data Article number: M502.413 GTIN: 4054469162584 ECLASS: 27272803 Brand: Metav IndustryLine Numbers / Core technical data Frequency: 7 MHz Measurement range: 0.75–80 mm Contact diameter: Ø 6 mm Cable length: approx. 1 m Connector: 8.5 Minimum test area indication: >Ø15×2 Commodity code: 90179000 Weight: 2 kg Designs / Special features Angled 90° probe head for restricted access Compact contact face for small radii and weld toes Prepared for use with ultrasonic thickness gauges Supplied as single probe, ready for connection FAQ What thickness range can be measured with this probe? The transducer supports a measurement range of 0.75–80 mm, allowing inspection of thin to moderate wall sections with a single sensor. Is the probe suitable for curved or small-diameter pipes? Yes. The angled 90° head and Ø 6 mm contact face are designed to access curved surfaces and smaller radii where straight probes are impractical. Which coupling medium should be used? Standard ultrasonic couplants are recommended to ensure consistent acoustic transmission; the probe operates with conventional coupling gels used in thickness measurement. Does the probe require a specific instrument connector? The transducer is supplied with an 8.5 connector and an approximately 1 m cable for direct connection to compatible ultrasonic thickness gauges. Are there limitations on minimum test area? Measurement reliability depends on sufficient sound-path geometry; the probe specification indicates a minimum test area of >Ø15×2 to achieve valid readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a heat‑resistant design, a broad 3–200 mm measurement range and a compact Ø14 mm footprint for dependable thickness checks on hot components; order the probe directly via Metav Werkzeuge or contact the consultants for application advice. Probe for Ultrasonic Thickness Gauge M502.414 – heat‑resistant, 5 MHz, Ø14 mm (Metav IndustryLine) The Probe for Ultrasonic Thickness Gauge M502.414 is a straight, heat‑resistant 5 MHz transducer intended for thickness testing of components from 3 to 200 mm in industrial environments Heat‑resistant up to 300°C Measurement range 3–200 mm 5 MHz frequency for general thickness testing 14 mm probe diameter, straight design Built for high‑temperature industrial measurement The straight probe is specified as heat‑resistant up to 300°C, making it suitable for inspections where elevated surface temperatures rule out standard transducers. The construction supports reliable coupling over short contact times, while the compact Ø14 mm face aids access in confined areas. This configuration reduces the need for cooling pauses during production checks and therefore contributes to uninterrupted quality control in heat‑affected processes. Reliable readings across a wide measurement band Designed around a 5 MHz element, the transducer provides a pragmatic balance between penetration and resolution for wall‑thicknesses from 3–200 mm. For workshop and shop‑floor applications this means one sensor can cover a broad set of tasks without frequent probe changes. The result is efficient inspection cycles and consistent comparative data for acceptance tests and maintenance rounds, supporting reproducible measurement routines in metalworking and fabrication contexts. Compatibility and handling that keep inspections efficient A robust cable of approximately 1 m and the specified connector support straightforward attachment to compatible ultrasonic thickness gauges. The straight geometry and small probe face simplify positioning on curved or limited surfaces, shortening set‑up times. Classified in the Standard class for thickness gauges, this transducer is a practical choice where stiffness, reach and one‑hand operation need to be balanced for everyday measurements. For precision high‑temperature thickness testing with the Metav IndustryLine M502.414 probe, contact Metav Werkzeuge for tailored advice and expedited delivery from Emmerich. Technical data Article number: M502.414 GTIN: 4054469162614 Manufacturer: Metav IndustryLine Facts Frequency: 5 MHz Measurement range: 3–200 mm Probe diameter: Ø14 mm Cable length: approx. 1 m Connector: 15 Weight: 2 kg Tariff number: 90179000 Special features Heat‑resistant <300°C Straight probe design Suitable for ultrasonic thickness gauges Minimum requirement: >Ø30x3 Label: Sonde für Ultraschall‑Dickenmessgerät Hitzebeständig 3 - 200 mm FAQ What temperature can the probe withstand? The probe is specified as heat‑resistant up to 300°C, allowing the M502.414 to be used on hot surfaces without premature degradation. Which thicknesses can be measured with this transducer? The transducer covers a measurement range of 3–200 mm, making it suitable for thin sheets through to moderate‑thickness structural parts. What frequency does the probe use and what does that mean? The probe operates at 5 MHz, offering a compromise between penetration and resolution that matches common workshop inspection tasks. What is the probe face diameter and why does it matter? The probe has a 14 mm face (Ø14 mm); a small contact area improves access to tight features and curved surfaces. Is the probe compatible with standard ultrasonic thickness gauges? Yes; the M502.414 is intended for use with ultrasonic thickness gauges and includes a 1 m cable and the specified connector for straightforward integration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com