175-200mm Three-Point Inside Micrometer Self-Centring, Analog 0.005mm Resolution, Supplied in Case - Metav IndustryLine

Precise internal measurement made simple: the combination of a self‑centring three‑point contact, accuracy ±0.008 mm, and a 175–200 mm measuring range ensures reproducible results across production runs. Order the three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed.

Three‑point internal micrometer M836.722 — Self‑centring, 175–200 mm (Metav IndustryLine)

A three‑point internal micrometer for reliable internal diameter checks in workshop inspection and production control.

• Self‑centring three‑point contact
• Accuracy ±0.008 mm
• Hardened measuring faces
• Supplied in protective case

Reproducible results through self‑centring three‑point contact

The three‑point contact design provides a self‑centring measuring principle that minimises operator‑dependent offset when checking bores and internal diameters. With an analogue readout and a finest reading increment of 0.005 mm, the instrument supports controlled, repeatable measurements appropriate for standard inspection tasks. The specified accuracy of ±0.008 mm places this tool in a precision class suitable for quality control where tight tolerances are required but micrometre‑level laboratory devices are not necessary. The mechanical design reduces setup time on repetitive checks and lowers the rate of rework by delivering stable centring without complex fixturing.

Built for everyday workshop demands

Constructed with hardened measuring faces, the device resists wear in routine use and maintains measurement integrity over prolonged service intervals. The instrument’s 175–200 mm span places it in the standard workshop range, offering a practical compromise between reach and rigidity for common internal measurement tasks on machine components, housings and assemblies. Supplied in a protective case, it is prepared for transport to and from the shop floor or for secure storage between shifts. The analogue format gives tactile feedback during measurement and removes dependency on batteries, supporting uninterrupted operation in busy production environments.

Improve process control and traceability

Integrating this three‑point internal micrometer into inspection routines sharpens statistical process control by reducing scatter in internal diameter readings. The robust, easy‑to‑handle geometry encourages consistent technique across operators, while the clear reading increment simplifies documentation and auditing. Together with Metav’s logistical and technical support, the instrument contributes to faster inspection cycles and more reliable acceptance decisions on the shop floor. Metav’s role as a precision‑partner translates into dependable delivery and product selection, making high‑quality measurement accessible across workshops and small production sites.

For reliable internal measurement on standard production runs, request the Metav IndustryLine three‑point internal micrometer (M836.722) via Metav Werkzeuge in Emmerich for expert advice and prompt dispatch

Technical data

• Article number: M836.722
• GTIN: 4061905040993
• Manufacturer: Metav IndustryLine

Facts

• Measuring range: 175–200 mm
• Accuracy: ±0.008 mm
• Reading: 0.005 mm
• Analogue instrument

Special features

• Self‑centring three‑point contact
• Hardened measuring faces
• Supplied in protective case

FAQ

How does the three‑point contact improve measurement reproducibility?
The three‑point design centres automatically in the bore so the contact points average out positional errors; the Metav IndustryLine three‑point internal micrometer (M836.722) therefore yields more reproducible internal diameter readings than two‑point gauges.

Is the instrument suitable for routine workshop inspection?
Yes — the 175–200 mm range and the mechanical, analogue operation are optimised for standard workshop and production control tasks, combining practicality with the stated ±0.008 mm accuracy.

Are the measuring faces durable for daily use?
The product features hardened measuring faces, which resist wear and extend stable performance over many inspection cycles on typical shop materials.

Does the device require batteries or electronic calibration?
The instrument is analogue and does not require batteries; calibration should follow the workshop’s metrology schedule and can be performed by an accredited service if traceable certificates are needed.

What does the supplied protective case mean for handling?
Delivery in a protective case protects the instrument during transport and storage and supports safe handling between inspection stations.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com