Wireless USB Receiver For Carbon Workshop Calipers - Metav IndustryLine

Take advantage of a light yet stiff carbon-fibre beam combined with steel measuring faces and reliable Digimatic/Bluetooth data transfer for fast, error‑reduced documentation and consistent workshop throughput; order via Metav Werkzeuge or consult our specialists for application advice. Filetta Digital Workshop Caliper M910.342 — Carbon‑fibre beam, 0–600 mm, Bluetooth The Filetta M910.342 is a robust digital workshop caliper designed for large‑format measurements in machine shops and fabrication environments, offering a high‑stiffness beam and protected electronics for everyday industrial use. Carbon‑fibre beam with steel measuring faces Measuring range 0–600 mm Digimatic and Bluetooth data output Dust‑ and waterproof to IP65 Stiff, lightweight construction for repeatable results The combination of a carbon‑fibre beam with steel measuring faces keeps mass low while preserving local stiffness at the jaws, resulting in a tool that is easier to handle over long strokes without sacrificing contact reliability. With a 0–600 mm measuring range and a 130 mm jaw, the caliper sits in the large‑range class (500–1,000 mm), making it suitable for measuring larger fixtures, housings and assemblies where beam rigidity and reproducibility are decisive. The overall length of 826 mm and a weight of 1.3 kg balance reach with manoeuvrability, reducing operator fatigue during repeated tasks. Practical precision and convenient handling for workshop control The instrument features a 0.01 mm display resolution and a stated accuracy of ±0.06 mm, which provides dependable workshop tolerances for production and inspection tasks where rapid checks and documented results are required. The slide offers fine adjustment and a locking screw for controlled, repeatable contact pressure; the specified measuring force of 5–10 N helps standardise contact while reducing variation from manual pressure. The digital display supports mm/Inch switching and ABS/INC modes, plus preset and reset functions, simplifying setup for batch work and first‑off inspections. Integrated data transfer and protected electronics for efficient processes Data can be output via Digimatic or Bluetooth, enabling direct capture into measuring software, spreadsheets or quality logs and minimising transcription errors in the production flow. The unit is sealed to IP65, protecting against dust and water jets commonly encountered in workshops, and is powered by a single CR2032 cell for long shelf and operating life. Delivery includes a protective case for safe transport and storage, so the device remains serviceable at the point of use and integrates smoothly into existing shop measurement routines. Contact Metav Werkzeuge for tailored advice on deploying the Filetta carbon‑fibre workshop caliper M910.342 in production and to discuss data integration; email info@metav-werkzeuge.com or call +49 2822 7131930 for proximity support from Emmerich. Technical data Article number: M910.342 Manufacturer: Filetta Name: Digital workshop caliper Carbon 0–600 mm IP protection: IP65 Facts Measuring range: 0–600 mm Resolution: 0.01 mm Accuracy: ±0.06 mm Overall length: 826 mm Jaw length: 130 mm Weight: 1.3 kg Measuring force: 5–10 N Battery: 1× CR2032 Special features Material: carbon‑fibre beam with steel measuring faces Data output: Digimatic and Bluetooth Display functions: mm/Inch, ABS/INC, On/Off, Reset/Preset Fine adjustment and locking screw Delivered in protective case FAQ How precise is this caliper for workshop checks? The Filetta M910.342 provides a display resolution of 0.01 mm with a stated accuracy of ±0.06 mm, suited to typical workshop tolerances and rapid inspection tasks. Can this caliper handle larger components and fixtures? Yes — with a 0–600 mm range and a 130 mm jaw it is classified in the large‑range category (500–1,000 mm) and is intended for measuring sizeable assemblies and machined parts. What options are available for data capture and logging? The instrument supplies measurement data via Digimatic and Bluetooth, allowing direct recording into measuring systems, data loggers or quality software without manual re‑entry. Is the caliper protected against coolant and dust? The unit is rated IP65, offering protection against dust ingress and low‑pressure water jets, suitable for workshop environments. Is a case and battery supplied with the caliper? The caliper is delivered in a protective case and uses one CR2032 battery for the electronics. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of a 600 mm measuring range, lightweight carbon‑fibre construction and integrated Digimatic and Bluetooth outputs ensures efficient measurement of large components with reliable data transfer; order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Digital Workshop Caliper Carbon 0–600 mm — long‑range digital caliper with carbon‑fibre beam and 200 mm jaws The Digital Workshop Caliper Carbon 0–600 mm is a robust, long‑reach measuring instrument designed for workshop and production environments where extended reach and mobile data capture are required Carbon‑fibre beam with steel measuring faces 600 mm measuring range for large components IP65‑rated dust and water protection Digimatic and Bluetooth data output Measure larger components with repeatable stability The caliper’s 600 mm span places it in the large‑range class (500–1,000 mm), making it suitable for substantial assemblies such as fixtures, housings and long shafts. The carbon‑fibre beam reduces overall mass while preserving profile stiffness; combined with steel measuring faces this yields a favourable stiffness‑to‑weight ratio that supports reproducible measurements along the entire jaw travel. This balance of reach and rigidity reduces the risk of bending‑induced error during hand measurements and simplifies two‑person handling for bulky parts. Accurate digital readout and seamless data capture Equipped with a digital display that reads to 0.01 mm and a stated accuracy of 0.08 mm, the instrument provides clear, machine‑readable values while minimising manual transcription. Dual data outputs—Digimatic and Bluetooth—enable direct connection to data collectors, inspection software or wireless logging systems, supporting streamlined quality control and traceable measurement records. The IP65 protection rating shields the electronics from workshop dust and splashes, extending service life under typical industrial conditions. Workshop ergonomics and secure handling A long 200 mm jaw length and total instrument length of 826 mm are paired with a practical fine‑adjustment wheel and a secure locking screw, allowing controlled closing and stable retention of readings. The caliper’s measured force range of 5–10 N promotes consistent contact pressure, which contributes to repeatability across multiple measures. Power is supplied by a single CR2032 cell for low maintenance, and the tool is delivered in a dedicated transport case to protect the instrument during transfer between job sites or storage. Integration into inspection routines and production flows Designed as a workshop‑grade digital caliper, the model supports quick inclusion into inspection routines thanks to its digital communication options and familiar keypad functions (mm/inch, ABS/INC, On/Off, Reset/Preset). For manufacturing environments that use digital readouts or SPC systems, the combined Digimatic and Bluetooth outputs significantly reduce data entry steps and help maintain consistent documentation. The unit’s construction and feature set make it a pragmatic choice for maintenance shops, jig and fixture assembly, and production lines where longer reach is required without sacrificing handling convenience. Contact Metav Werkzeuge for technical advice and delivery from our Emmerich warehouse on the Filetta carbon‑fibre 0–600 mm caliper (SKU M910.343); email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored assistance Technical data Article number: M910.343 Label: Digital Workshop Caliper Carbon 0–600mm and 200mm jaw length Manufacturer: Filetta Key figures Measuring range: 0–600 mm Maximum measuring range: 600 mm Total length: 826 mm Jaw length: 200 mm Weight: 1.4 kg Reading resolution: 0.01 mm Accuracy: 0.08 mm Measuring force: 5–10 N Protection class: IP65 Battery: 1x CR2032 Special features Carbon‑fibre beam with steel measuring faces Data output: Digimatic and Bluetooth Display functions: mm/inch, ABS/INC, On/Off, Reset/Preset Fine adjustment wheel and locking screw Delivered in a transport case Robust workshop design suitable for long‑range measurements FAQ What measuring range does this caliper cover? The Digital Workshop Caliper Carbon covers a range of 0–600 mm, making it suitable for larger workshop components and fixtures. Which data interfaces are available for measurement collection? This Filetta caliper offers both Digimatic and Bluetooth outputs for wired and wireless data transfer to readout devices and inspection systems. Is the caliper protected against dust and water? The instrument is rated IP65, providing protection against dust ingress and low‑pressure water jets typical in workshop environments. What power source does the caliper use and how long does it last? Power is via a single CR2032 battery; actual service life depends on usage patterns and wireless operation. Does the caliper include a fine adjustment or locking mechanism? Yes, it features a fine‑adjustment wheel for controlled closing and a locking screw to secure measurements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a robust combination of carbon‑fibre construction, steel measuring faces and reliable data transfer via Digimatic and Bluetooth to speed up workshop measurement tasks and reduce rework. Order the caliper directly via Metav Werkzeuge or consult our specialists for integration advice. Filetta Digital Workshop Caliper M910.344 — carbon body, 0–600 mm, 300 mm jaw length The Filetta Digital Workshop Caliper M910.344 is a long‑range digital caliper designed for large workshop components and industrial measurement tasks, pairing a lightweight carbon‑fibre beam with hardened steel measuring faces for repeatable results. Carbon‑fibre beam with steel faces IP65 protection for harsh environments Digimatic and Bluetooth data output 300 mm long jaws for deep reaches Fine adjustment and locking screw Durable construction for dependable workshop use The long‑span design combines a carbon‑fibre beam with steel measuring faces, which reduces weight without sacrificing the contact rigidity required for repeatable readings. Built to the 500–1,000 mm class of calipers, this instrument is intended for larger components where profile stiffness matters over the full measuring length. An IP65 rating guards electronics and slides against dust and water jets, keeping maintenance overhead low in busy production environments. Fast, traceable measurement workflow with modern outputs Equipped with both Digimatic and Bluetooth data outputs, the instrument supports immediate transfer to data loggers or SPC systems, accelerating quality documentation and minimising transcription errors. The digital display offers mm/inch switching, ABS/INC modes and a Reset/Preset function, while the readout resolution is 0.01 mm, enabling efficient inspection routines. Combining electronic transfer with a mechanical locking screw and fine‑adjustment control keeps measurements stable and reproducible during capture. Practical handling, delivery and operating details The caliper operates with a single CR2032 battery and is tuned for a measuring force of 5–10 N, a range that balances tactile control with consistent contact pressure. Long jaws of 300 mm reach into deeper slots and pockets, while the overall length of 826 mm and weight of 1.5 kg remain manageable for one‑person handling or two‑person tasks where required. Delivery includes a protective transport case and the instrument’s robust sliding mechanism simplifies everyday shop use without constant recalibration. Discuss the Filetta M910.344 with Metav Werkzeuge for a tailored supply and integration plan — contact Metav Werkzeuge in Emmerich to confirm suitability and delivery options Technical data Article number: M910.344 Manufacturer: Filetta Label: Digital‑workshop caliper carbon 0–600 mm and 300 mm jaw length Battery: 1x CR2032 Protection class: IP65 Material: Carbon fibre with steel measuring faces Measuring range: 0–600 mm Total length: 826 mm Weight: 1.5 kg Core specifications Readout resolution: 0.01 mm Accuracy: 0.12 mm Jaw length: 300 mm Measuring force: 5–10 N Features and functions Digital display with mm/inch, ABS/INC, On/Off, Reset/Preset Data output: Digimatic and Bluetooth Fine adjustment mechanism Locking screw for fixed measurements Delivered in protective transport case FAQ What is the measuring range and accuracy of the caliper? The Filetta Digital Workshop Caliper M910.344 measures from 0 to 600 mm with an accuracy of ±0.12 mm and a readout resolution of 0.01 mm. How can measurement data be transferred from the instrument? Data can be output via Digimatic interface or Bluetooth, allowing the Filetta caliper M910.344 to feed measurements directly into SPC or data‑collection systems. Is the instrument suitable for workshop conditions? Yes — the carbon‑fibre beam with steel faces, IP65 protection and a protective transport case make the Filetta M910.344 well suited for workshop and shop‑floor environments. What additional handling features improve measurement consistency? The caliper includes a fine‑adjustment control and a locking screw, and it maintains consistent contact pressure within the 5–10 N measuring force range to reduce operator‑induced variance. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a carbon-fibre beam with steel measuring faces, a full 0–1000 mm measuring range and reliable Digimatic/Bluetooth data transfer for uninterrupted workshop throughput; order directly via Metav Werkzeuge or consult our specialists for application advice. Digital workshop caliper M910.345 — carbon-fibre beam, Bluetooth & Digimatic The Digital workshop caliper M910.345 is a long-range measuring instrument designed for workshop and production use, combining a lightweight carbon-fibre beam with robust steel measuring faces for repeatable measurements on large components. Carbon-fibre beam with steel measuring faces 0–1000 mm measurement range with 130 mm jaws Digimatic and Bluetooth data output, IP65 protected Extended reach for large components and fixtures A measuring span of 0–1000 mm positions this instrument in the large-range class (500–1,000 mm), making it suitable for sizeable parts such as fixtures, housings and large workpieces. The extended reach reduces the need for multiple measuring tools and speeds up set-up and inspection cycles, delivering a clear efficiency gain on the shop floor. The long-beam design keeps rigidity where it matters so that repeatability is maintained across the whole measuring length. Precise digital readings and seamless data handling Equipped with a digital system that resolves to 0.01 mm, the caliper provides straightforward numeric read‑outs and selectable units for millimetres or inches. Data output via Digimatic and Bluetooth enables direct capture into measurement software or production control systems, eliminating manual transcription and lowering error risk. Stated repeatability and measurement stability reflect an effective error behaviour of ±0.08 mm, while the controlled measuring force of 5–10 N helps to reduce operator-induced variation. Workshop-proof construction with low weight The combination of a carbon-fibre beam with steel measuring faces achieves a beneficial balance between lightweight handling and wear-resistant contact surfaces. An IP65 rating protects the electronics and slide from dust and coolant exposure, enhancing uptime in demanding environments. With a jaw length of 130 mm the instrument reaches into recesses and across features while the total weight of about 1.5 kg keeps single-person handling practical for routine inspection tasks. Workflow-friendly features for industrial use Fine adjustment and a secure locking screw simplify clamping and incremental positioning during layout and inspection work. The instrument runs on a CR2032 battery and is delivered in a protective case for safe transport and storage between jobs. Designed for integration with standard data acquisition chains, the caliper supports faster documentation and traceability, helping production teams to maintain throughput without compromising on measurement quality. Speak to Metav Werkzeuge for application guidance on the Filetta carbon-fibre digital workshop caliper M910.345 — contact info@metav-werkzeuge.com or call +49 2822 7131930 for specification matching and procurement support. Technical Data Article number: M910.345 Manufacturer: Filetta Material: Carbon fibre with steel measuring faces Range: 0–1000 mm Protection class: IP65 Facts Resolution: 0.01 mm Accuracy / repeatability: ±0.08 mm Jaw length: 130 mm Measuring force: 5–10 N Weight: 1.5 kg Overall length: 1226 mm Power supply: 1× CR2032 Special features Digimatic and Bluetooth data output Digital display with mm/inch, ABS/INC, Reset/Preset Fine adjustment and locking screw Delivered in protective case Classified for large-range (500–1,000 mm) long-beam applications FAQ Is this caliper suitable for measuring large workshop components? Yes. The Filetta digital workshop caliper M910.345 is designed for large-range measurements up to 0–1000 mm, making it well suited to fixtures, housings and other sizeable workshop components. How accurate are measurements taken with this instrument? The caliper provides a resolution of 0.01 mm and a stated measurement behaviour around ±0.08 mm, supported by a controlled measuring force to improve repeatability. Can measurement data be transferred directly to a computer or data logger? Yes. The instrument offers Digimatic and Bluetooth outputs for direct integration with data collection systems and inspection software. Is the caliper protected against coolant and dust in a machining environment? The caliper has an IP65 protection rating, which provides resistance to dust and low-pressure water jets typically encountered in workshop settings. Does the delivery include a case for transport and storage? A protective case is supplied with the instrument to simplify safe transport and on-site storage between measurement tasks. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of lightweight construction, robust measuring faces and integrated data output for dependable workshop measurement. The carbon‑fibre beam and steel measuring surfaces provide a favourable stiffness‑to‑weight ratio, while digimatic and Bluetooth outputs support modern production workflows. Order the Filetta digital workshop caliper directly via Metav Werkzeuge or ask Metav’s consultants if additional specifications are required. Digital workshop caliper M910.346 — carbon‑fibre beam, 0–1000 mm, Bluetooth (Filetta) The Digital workshop caliper M910.346 is a rugged 0–1000 mm workshop instrument designed for industrial measurement tasks, combining a lightweight carbon‑fibre beam with steel measuring faces and dual data outputs for process integration. Carbon fibre beam with steel measuring faces Measurement range 0–1000 mm Digimatic and Bluetooth data output IP65 protection for harsh environments Large‑range capability without heavy handling The caliper is classified for the 500–1,000 mm range, making it suitable for large‑format workshop tasks where reach and repeatability matter. The carbon‑fibre beam reduces overall mass to 1.6 kg, improving handling during longer measurements, while the steel measuring faces preserve wear resistance where contact is concentrated. This combination gives a practical compromise between stiffness and ease of use, so measurements across assemblies and fixtures remain reproducible without unnecessary operator fatigue. Reliable digital capture for production processes Equipped with digimatic and Bluetooth outputs, the instrument supports direct data transfer into SPC systems and measurement logs. The display resolution is 0.01 mm, enabling fine reading for quality control, and the caliper features a fine‑adjustment thumbwheel and a locking screw for secure setting. The specified measuring force of 5–10 N contributes to repeatability by standardising contact pressure during checks. These attributes make the device a practical choice where traceable, machine‑readable readings speed up inspection routines and reduce transcription errors. Built to endure in workshop environments An IP65 rating shields the electronics against dust and jets of water, while the supplied protective case simplifies transport and on‑site storage. The instrument’s overall length of 1,226 mm and 200 mm jaw length provide the extra reach needed for larger components without compromising robustness. Power is supplied by a single CR2032 battery, keeping maintenance straightforward; the caliper’s compact electronics and sealed design reduce downtime and extend service intervals. Practical integration and everyday benefits Functionality focuses on workshop efficiency: the lightweight construction shortens handling time, digital outputs remove manual logging, and the locking screw plus fine adjustment allow precise setting for repetitive operations. As a workshop instrument, it is appropriate for heavy‑duty measurement tasks and suits environments where a balance of reach, durability and digital connectivity is required. Compatibility with common digimatic interfaces ensures simple integration with existing measurement stations. For a practical, connected measuring solution, contact Metav Werkzeuge to discuss the Filetta digital workshop caliper M910.346 and arrange delivery or integration details via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M910.346 Manufacturer: Filetta Product: Digital workshop caliper Carbon 0–1000 mm Weight: 1.6 kg Overall length: 1,226 mm Jaw length: 200 mm Battery: 1x CR2032 Facts Resolution: 0.01 mm Specified accuracy: 0.12 mm Measuring force: 5–10 N Protection class: IP65 Special features Carbon fibre beam with steel measuring faces Digimatic and Bluetooth data output Fine adjustment wheel Locking screw Supplied in protective case FAQ What measurement range does the caliper cover? The Filetta digital workshop caliper M910.346 covers a measuring range of 0–1000 mm and is intended for large‑range workshop measurement tasks. Which outputs are available for data capture? This caliper provides both digimatic and Bluetooth outputs for direct transfer of readings into data collection systems and digital inspection workflows. How precise is the instrument and what is the display resolution? The instrument has a display resolution of 0.01 mm and a specified accuracy of 0.12 mm, with a measuring force of 5–10 N to aid repeatability. Is the caliper suitable for harsh workshop conditions? Yes. The caliper is rated IP65, protecting it against dust ingress and water jets, and it is supplied in a protective case for transport and storage. What materials form the measuring surfaces and beam? The beam is made from carbon fibre to reduce weight, while the measuring faces are steel for durability and wear resistance. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Benefit from a combination of a carbon-fibre beam, 0–1000 mm measuring range and IP65 protection for dependable shop‑floor measurement of large components; order this caliper directly via Metav Werkzeuge or ask our specialists for further advice. Digital workshop caliper Carbon 0–1000 mm — Precision caliper with long jaws and data output (Filetta) Digital workshop caliper Carbon 0–1000 mm designed for robust measurement tasks where reach, repeatability and digital data transfer are essential Carbon-fibre beam with steel measuring faces 0–1000 mm measuring range IP65 dust and water protection Digimatic + Bluetooth data output Accurate long‑range measurement for the busy workshop The 0–1000 mm measuring range paired with a carbon‑fibre beam delivers a favourable ratio of reach to stiffness that reduces deflection during handling. With an indicated accuracy ±0.16 mm and resolution 0.01 mm, the instrument provides rapid, repeatable readings for routine control tasks and setup operations. The long 300 mm jaw length gives access to deeper features and larger assemblies without compromising the stability of the measuring faces. This combination supports efficient process checks and reduces rework by making critical dimensions easy to verify on the bench or in the jig area. Digital output and traceable data capture for production control Equipped with both Digimatic and Bluetooth data interfaces, the caliper enables fast transfer of measurements into inspection systems or SPC software, improving traceability and reducing transcription errors. The digital display includes mm/inch, ABS/INC, and reset/preset functions for straightforward switching between modes and quick zeroing at reference points. Integrating the instrument into a digital workflow shortens inspection cycles and supports documented quality procedures, delivering tangible time savings and clearer audit trails for production quality control. Designed for workshop durability and comfortable handling The combination of a lightweight carbon beam and steel measuring faces offers robust contact surfaces where wear matters while keeping overall instrument mass low. Rated IP65, the caliper tolerates dusty environments and occasional water exposure typical of workshop settings. A fine‑adjustment mechanism and locking screw facilitate controlled closing and stable readings on irregular parts; power is supplied by a single CR2032 battery for long service life and easy replacement. The instrument is delivered in a protective transport case to simplify handling and safe storage when moving between workstations. Practical classification and typical applications This caliper falls into the category for long‑span workshop calipers, suitable for heavy machining, fixtures, pipe and vessel components, and mold or die assemblies where measurements up to one metre are required. The measured 5–10 N measuring force balances reliable contact without excessive deformation on thin‑walled sections. In practice, the tool is a reliable choice for maintenance teams, toolrooms and production shops that demand robust long‑reach measurement with digital data capture and straightforward operation. Contact Metav Werkzeuge in Emmerich to discuss suitability for specific tasks or to arrange procurement and technical consultation: info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: M910.347 Label: Digital-Werkstattmessschieber Carbon 0-1000mm und 300mm Schnabellänge Manufacturer: Filetta Material: Carbon-fibre beam with steel measuring faces Protection class: IP65 Power: 1x CR2032 Measuring range: 0–1000 mm Resolution: 0.01 mm Accuracy: ±0.16 mm Facts Total length: 1226 mm Weight: 1.7 kg Jaw length: 300 mm Measuring force: 5–10 N Digital display: mm/inch, ABS/INC, Reset/Preset Special features Digimatic and Bluetooth data output Fine adjustment mechanism Locking screw for repeatable readings Delivered in a transport case for safe handling Suitable for workshop and production environments FAQ What measuring range does the caliper cover? The caliper offers a measuring range of 0–1000 mm, making it suitable for larger components and assemblies. Which materials are used in the caliper construction? The instrument combines a carbon‑fibre beam with steel measuring faces to provide a lightweight yet durable measuring device. How are measurements transferred to a PC or data system? Measurements can be output via Digimatic interface or Bluetooth, enabling direct capture into inspection software or SPC systems. Is the caliper suitable for use in a dusty or wet workshop? Yes, the caliper is rated IP65, offering protection against dust ingress and low‑pressure water jets typical in workshop environments. What battery does the caliper use and how long does it last? The caliper is powered by a single CR2032 battery, which is commonly used and straightforward to replace. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combine the lightweight carbon construction with robust steel measuring faces and integrated Digimatic & Bluetooth output to secure reliable long‑range measurement across the workshop; order the unit directly via Metav Werkzeuge or consult our specialists for application advice. Digital workshop caliper Carbon 0–1500 mm (M910.349) — Bluetooth & Digimatic, IP65, Filetta A Digital workshop caliper Carbon 0–1500 mm engineered for long‑span measurements in demanding workshop environments, combining a low‑weight carbon main beam with steel contact faces for wear resistance and repeatability 0–1500 mm measuring range Carbon body with steel measuring faces Digimatic and Bluetooth data output IP65 protection with fine adjustment and lock Long‑reach measurement with controlled stiffness The caliper is built around a 0–1500 mm measuring range, placing it in the Long class suitable for metre‑scale components. The carbon fibre beam reduces overall mass while preserving profile stiffness, which limits sag and keeps measurements reproducible across the full travel. Steel contact faces on the jaws provide wear resistance where it matters, so contact surfaces remain true over repeated use. With an overall length of 1736 mm and a net weight of approximately 2 kg, the instrument balances reach and handling for two‑person workflows or fixed jig measurements without compromising on portability. Consistent precision, easy handling and workshop resilience Measurement electronics provide an resolution of 0.01 mm with a stated accuracy of ±0.16 mm, a combination targeted at robust workshop control rather than ultra‑micrometre lab work. A fine‑adjustment thumbwheel and a separate locking screw ensure setting and clamping are straightforward, while a controlled measuring force of 5–10 N helps reduce operator‑induced variation. The sealed housing meets IP65 protection, keeping out dust and spray, and the display offers mm/inch switching, ABS/INC zeroing and a reset/preset function. Power is supplied by a single CR2032 cell for extended standby life. Seamless data capture and transport protection Integrated Digimatic and Bluetooth output enables direct data collection into digital readout systems or wireless data loggers, simplifying quality documentation and integration into Industry 4.0 processes. The digital interface supports fast transfer of measurement points and reduces transcription errors in production or inspection routines. The caliper is supplied in a protective transport case for safe shipping and onsite movement, and its combination of low weight and solid jaw finish makes it suitable for heavy workshop use where ruggedness and connectivity are equally important. For long‑range workshop measurement from Filetta, contact Metav Werkzeuge in Emmerich for tailored technical advice and to arrange supply of the Filetta digital workshop caliper; email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: M910.349 Brand: Filetta Label: Digital‑workshop caliper Carbon 0–1500 mm and 150 mm jaw length Numbers / Core technical data Measuring range: 0–1500 mm Overall length: 1736 mm Jaw length: 150 mm Resolution: 0.01 mm Stated accuracy: ±0.16 mm Measuring force: 5–10 N Weight: 2 kg Battery: 1 × CR2032 Designs / Special features Carbon fibre main beam with steel measuring faces Digimatic and Bluetooth data output Digital display with mm/inch, ABS/INC, reset/preset functions Fine‑adjustment thumbwheel and locking screw IP65 protection class for dust and spray resistance Delivered in a protective transport case FAQ Is this caliper suitable for measuring large components such as machine housings or shafts? Yes. The Filetta digital workshop caliper with a 0–1500 mm range and a lightweight carbon beam is intended for metre‑scale components where long reach and manageable handling are required. How is data transferred from the instrument to a computer or data logger? Data can be output via the integrated Digimatic interface or wirelessly over Bluetooth, enabling direct capture into inspection software or portable data collection devices. What protection does the instrument offer against dust and coolant? The caliper has an IP65 rating, providing protection against dust ingress and low‑pressure water jets, suitable for typical workshop environments. Are the contact faces durable for frequent use on metal parts? Yes. The contact faces are made of steel to resist wear during repeated contact with metal components, maintaining measurement reliability over time. Does the delivery include a case and is the instrument ready to use? The product is supplied in a protective transport case and comes with its battery fitted; routine setup (zeroing/preset) is performed via the digital controls. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of a carbon‑fibre beam with steel measuring faces, a 0–1500 mm measuring range and robust IP65 protection for reliable large‑format workshop measurement; order this caliper via Metav Werkzeuge or consult our advisors for technical clarification. Filetta Digital Workshop Caliper M910.350 — Carbon‑fibre, 0–1500 mm, IP65 The Filetta Digital Workshop Caliper M910.350 is a long‑range precision caliper designed for workshop and production measurement of larger components up to 1,500 mm. Carbon‑fibre beam with steel measuring faces 0–1500 mm measuring range Digimatic and Bluetooth data output IP65 protection for harsh environments Reliable large‑range measurement for heavy workshop use The long‑range design delivers a 0–1500 mm measuring capability while remaining manageable in typical workshop workflows; classified in the Long category for calipers, this range bridges handheld convenience and extended reach for fixtures, housings and larger assemblies. The combination of a lightweight carbon‑fibre beam with hardened steel measuring faces reduces deflection while preserving durable contact surfaces, so repeatable external and step measurements are achievable across the full span. The specified display resolution of 0.01 mm supports fine increments, and the listed accuracy provides a clear expectation of measurement tolerance for shop‑level inspection. Industrial data transfer and practical controls for production lines Equipped with both Digimatic and Bluetooth outputs, the instrument supports wired collection and wireless integration into data logging workflows, enabling direct capture of readings into SPC or measurement software. The digital display offers mm/inch selection and ABS/INC modes, plus Reset/Preset convenience for quick zeroing and reference offsets. A dedicated fine‑adjustment and a locking screw permit controlled closing and stable clamping of the slider, reducing the risk of inadvertent reading shifts during transfer or recording. These features together accelerate measurement cycles and cut transcription errors in repetitive tasks. Built for durability and everyday workshop handling Protection to IP65 keeps dust and jets of water from compromising internal electronics, making this caliper suited to tougher environments where coolant and contamination are present. The instrument runs from a standard CR2032 cell and its overall mass and balance are arranged for two‑hand handling when required; the total length supports measurements up to 1,500 mm while the 300 mm jaw length provides secure contact for large parts. The construction targets a pragmatic trade‑off between stiffness and weight, helping teams maintain throughput without sacrificing the robustness expected from a workshop caliper. For specification matching or to arrange a technical consultation about the Filetta caliper and its integration into existing measuring routines, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists in Emmerich will advise on compatibility and delivery options Technical data Article number: M910.350 Brand: Filetta Battery: 1x CR2032 IP rating: IP65 Material: Carbon fibre with steel measuring faces Facts Measuring range: 0–1500 mm Total length: 1736 mm Weight: 2.1 kg Resolution: 0.01 mm Accuracy: 0.21 Jaw length: 300 mm Measuring force: 5–10 N Digital: Yes Special features Digimatic and Bluetooth data output Display functions: mm/Inch, ABS/INC, Reset/Preset Fine adjustment and locking screw Designed for workshop and production use FAQ What measuring range does this caliper cover? The Filetta Digital Workshop Caliper M910.350 covers a 0–1500 mm measuring range suitable for larger workshop components. Is the caliper suitable for use in wet or dusty environments? Yes. The instrument is rated IP65, providing protection against dust ingress and water jets, which makes it appropriate for many workshop conditions. How are measurements exported from the device? Measurements are available via Digimatic output for wired data logging and Bluetooth for wireless transmission to compatible systems. What resolution and accuracy can be expected? The display resolution is 0.01 mm and the device is specified with an accuracy value of 0.21 as provided in the technical data. Does the caliper require a special battery? No special battery is required; the caliper runs on a standard CR2032 cell. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combine a 0–2000 mm measuring range with a carbon‑fibre construction and IP65 protection to measure large components reliably; order directly via Metav Werkzeuge or consult their technical team for specification matching. Filetta M910.352 digital workshop caliper — Carbon fibre body, 0–2000 mm range, IP65 The Filetta M910.352 digital workshop caliper is a long‑range, rugged measuring instrument designed for heavy workshop and production use, offering digital output for process integration and robust protection for harsh environments. Carbon fibre body, steel measuring faces 0–2000 mm measuring range for large parts IP65 protection for workshop conditions Digimatic and Bluetooth data output Large‑format accuracy for production and jig work Designed for extended measurements, this caliper belongs to the Long class (measuring range up to 2,000 mm), which is ideal when reach must be balanced with handling and stiffness. The combination of a carbon‑fibre main beam and steel measuring faces reduces weight while preserving contact rigidity, so measurements across long spans remain reproducible. With an indicated accuracy of 0.21 mm, the instrument delivers reliable results for workshop control tasks and large assembly checks, where repeatability and durability matter as much as reach. Digital readings and seamless data capture The unit provides a clear digital display with mm/Inch toggle and ABS/INC, plus Reset/Preset functions for quick setup. Data output supports both Digimatic and Bluetooth, enabling direct transfer of readings into inspection software or SPC systems and cutting transcription errors. The display resolution of 0.01 mm offers fine numerical detail for standard quality control, while the digital interfaces simplify documentation and traceable data collection in production environments. Built for workshop conditions and practical handling With an IP65 rating and a total length of 2,246 mm, the instrument stands up to dust and splash exposure common in machine shops. A lock screw secures positions for stable measurement, and a fine‑adjustment mechanism allows precise approach to contact points on large parts. Power is provided by a single CR2032 battery for convenient exchange on the shop floor. The caliper’s weight of 2.6 kg keeps it manageable for two‑person handling during longer measurements without compromising robustness. Benefits that support workflow and traceability A 200 mm jaw length gives secure contact on bulky components and fixturing, while the measured 5–10 N contact force balances surface protection with stable contact. The instrument is supplied in a protective case to simplify transport and storage between job sites or bench and machine. Together, these features reduce handling time, improve data reliability and integrate measurement into digital quality routines, helping to sustain a smooth production flow. Contact Metav Werkzeuge for a technical consultation and shipment from Emmerich — Metav’s quality filter ensures consistent production readiness and reliable supply for precision workshops. Technical data Article number: M910.352 Manufacturer: Filetta Product type: Digital workshop caliper Label: Digital workshop caliper Carbon 0–2000 mm and 200 mm jaw length Facts Measuring range: 0–2000 mm Accuracy: 0.21 mm Display resolution: 0.01 mm Total length: 2246 mm Jaw length: 200 mm Weight: 2.6 kg Measurement force: 5–10 N Battery: 1x CR2032 Protection class: IP65 Special features Carbon‑fibre beam with steel measuring faces Digimatic and Bluetooth data output Digital display with mm/Inch, ABS/INC, Reset/Preset Fine‑adjustment mechanism Lock screw for fixed measurements Supplied in protective case Digital instrument FAQ What accuracy can be expected for long measurements? The Filetta M910.352 digital workshop caliper specifies an accuracy of 0.21 mm, giving dependable results for large‑format workshop checks and assembly verification. Which data outputs are supported for process integration? This caliper offers Digimatic and Bluetooth outputs so readings from the Filetta caliper can be captured directly into inspection software or SPC systems. Is the caliper suitable for use in dusty or damp environments? Yes — the instrument has an IP65 rating, making it resistant to dust and splash water commonly found in production environments. Does the instrument include a transport or storage solution? The caliper is supplied in a protective case, facilitating safe transport and storage between workstations. How is the instrument powered and how easy is battery replacement? Power is from one CR2032 cell; replacement is straightforward and can be carried out on the shop floor without special tools. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of a lightweight carbon fibre beam, long 0–2000 mm measuring range and integrated Digimatic & Bluetooth outputs for efficient, traceable workshop measurement of large components; order directly via Metav Werkzeuge or ask our consultants for configuration and delivery details. Filetta Digital workshop caliper M910.353 — carbon beam, Digimatic & Bluetooth outputs The Filetta digital workshop caliper M910.353 is a robust, long-range measuring instrument designed for heavy-duty workshop use and data‑driven workflows. Carbon fibre main beam for low weight and high stiffness IP65 protection for shop-floor resilience Digimatic and Bluetooth data outputs for integration 300 mm jaws with hardened steel measuring faces Greater reach with manageable handling for large components This calliper combines a 0–2000 mm measuring range with a carbon fibre main beam to deliver the reach required for large fixtures while keeping handling ergonomic. The reduced mass — nominally 2.7 kg — and the extended overall length enable measurements across large workpieces without the full weight penalty of steel long‑balken callipers. Classified among long‑range workshop callipers, it is suited to applications where repeatable length checks on sizable assemblies, housings or long shafts are needed, yet portability and ease of two‑person handling remain relevant. Reliable numeric output and controlled measurement for fewer errors Measurement is presented on a digital display with 0.01 mm readout resolution and a specified accuracy of 0.25 as supplied. The instrument features mm/inch switching, ABS/INC mode, Preset/Reset and an integrated fine‑adjustment thumbwheel plus a locking screw to fix a reading. A controlled measuring force of 5–10 N reduces variance caused by operator pressure, helping to maintain consistent results between operators. For data workflows, both Digimatic and Bluetooth outputs transmit values directly to data collectors, SPC systems or DROs, reducing transcription errors and saving process time during serial inspections. Workshop durability, transport security and simple power supply Protection to IP65 guards the electronics against dust and splash exposure typical of busy workshops. Measuring faces are steel‑hardened for wear resistance where the jaws contact parts, while the carbon beam resists bending and keeps the instrument lightweight. Power comes from a single CR2032 battery for extended runtime in routine use. Delivery includes a protective transport case to safeguard the calliper during storage and transfer, ensuring the tool reaches the bench ready for immediate use. Contact Metav Werkzeuge for a technical consultation and delivery plan for the Filetta digital workshop caliper M910.353, including integration options for Digimatic and Bluetooth data capture Technical data Article number: M910.353 Manufacturer: Filetta Product type: Digital workshop caliper Measuring range: 0–2000 mm Jaw length: 300 mm Overall length: 2246 mm Resolution: 0.01 mm Specified accuracy: 0.25 Measuring force: 5–10 N Weight: 2.7 kg Power: 1x CR2032 Protection class: IP65 Material: Carbon fibre beam with steel measuring faces Data outputs: Digimatic and Bluetooth Display functions: mm/inch, ABS/INC, Preset/Reset Fine adjustment and locking screw Delivered in a transport case Designed for workshop and heavy‑duty measurement FAQ What range of parts is this calliper designed for? The Filetta digital workshop caliper M910.353 covers a 0–2000 mm measuring range, making it suitable for large components, fixtures and long shafts commonly found in machine and tool rooms. How is data transferred from the instrument to inspection systems? This model provides both Digimatic and Bluetooth outputs; values can be sent directly to data loggers, DROs or SPC software for streamlined documentation and reduced manual entry. Is the instrument dust‑ and splash‑resistant for shop use? Yes, the caliper has IP65 protection which shields the electronics against dust ingress and low‑pressure water jets, improving reliability in workshop environments. What ensures consistent readings between operators? The combination of a controlled measuring force (5–10 N), the fine‑adjustment thumbwheel and the locking screw helps to standardise contact pressure and preserve measured values, reducing operator‑related variance. Are the measuring faces wear resistant for long service life? The jaws are fitted with hardened steel measuring faces to resist wear from repeated contact and to retain dimensional accuracy over time. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com