Ausstattungen für Fräsmaschinen

Take advantage of the combination of a wide 0–85 mm clamping range, a compact footprint and a sturdy 3.5 kg mass to improve drilling accuracy and reduce rework; order directly via Metav Werkzeuge or ask our consultants for further specification support. DV-85 Drill Vice — Compact 0–85 mm clamping range, robust 3.5 kg construction (Vertex) The DV-85 is a compact drill vice engineered for secure clamping on drill presses and bench-mounted operations, offering stable positioning for routine workshop drilling and light fabrication tasks. 0–85 mm clamping capacity Compact footprint: 167 x 287 x 56 mm Sturdy 3.5 kg mass for stability Suitable for drill-press and bench use Improve drilling accuracy with stable clamping A stable clamping solution reduces wobble and misalignment during drilling, which directly improves hole quality and repeatability. The 0–85 mm jaw span enables a broad range of workpiece sizes to be held without frequent repositioning. By combining a robust 3.5 kg body with a precise jaw travel, the vice minimises vibration and supports consistent centreline retention. This reliability translates into fewer scrapped parts and less time spent on corrective machining, making the device a pragmatic choice for production-support and maintenance workshops. Save space without sacrificing functionality Workshops with limited bench space benefit from the compact dimensions of this vice (167 x 287 x 56 mm), which provide a small footprint while maintaining full clamping capability. The vice is suitable for both drill-press tables and general bench mounting where a stable hold is required. Its low profile helps to keep the working envelope clear, allowing easier access with drill chucks and depth stops. The compact layout supports efficient workflow organisation and faster set-ups between operations. Designed for consistent, user-friendly operation The mechanical design focuses on straightforward clamping action and dependable holding force. The vice’s mass contributes to stability under load, helping to keep cut forces in check during through-drilling and reaming tasks. Where precise positioning matters, the vice complements common workshop fixturing by offering predictable behaviour under repeated cycles. Where technical understanding is limited, the basic mechanics are simple to explain: wider jaw travel equals greater versatility, and a heavier body generally improves steadiness under cutting forces. Practical considerations and material compatibility The vice is intended primarily for conventional drilling and light fabrication tasks in steel, aluminium and other common workshop materials. The wide jaw aperture supports a variety of shapes and sizes, reducing the need for frequent tool changes or auxiliary clamps. For users integrating the vice into a production environment, the straightforward geometry and compact size make it a good option for jigs, small runs and repair work. When higher clamping forces or specialised jaws are required, the vice can be partnered with purpose-made soft jaws or parallels to protect delicate surfaces. For reliable precision clamping from Vertex, contact Metav Werkzeuge in Emmerich for tailored purchasing advice and technical guidance: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: DV-85 GTIN: 4061905083907 ETIM: EC002173 eClass: 21020601 Facts Opening range: 0–85 mm Dimensions: 167 x 287 x 56 mm Weight: 3.5 kg Special features Designation: Drill vice (Bohrschraubstock) Manufacturer: Vertex Gallery images available FAQ What clamping range does the vice cover? The DV-85 drill vice provides a clamping range of 0–85 mm, suitable for a wide variety of small to medium workpieces. Can the vice be used on a standard drill press table? Yes. The DV-85 by Vertex is intended for drill-press and bench mounting; its compact footprint and stable mass support typical drilling setups. How heavy is the vice and why does that matter? The vice weighs 3.5 kg; this mass helps to reduce vibration and improves stability during cutting for more accurate holes. Are soft jaws or parallels available for delicate workpieces? Soft jaws and parallels are commonly used with drill vices to protect surfaces; while not supplied with the DV-85, compatible accessories can be fitted to the jaws. Which materials are suitable for use with this vice? The vice is suitable for everyday workshop materials such as steel and aluminium; for specialised materials or cutting conditions, consider matching tooling and clamping accessories. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Benefit from precise, adjustable clamping with a high holding force and compact dimensions; the combination of reliable 1,800 kgf clamp force, straightforward mounting and a small footprint supports consistent workpiece stability and efficient cycle times. Order the component directly via Metav Werkzeuge or ask the consultants for tailored advice. SV-85 adjustable clamping jaws — 1,800 kgf clamp force (Vertex) An adjustable jaw set, the SV-85 provides secure workpiece holding for machining and inspection tasks in compact workshop and production environments Adjustable clamping for varied workpiece sizes 1,800 kgf clamp force for reliable holding Compact 86.5×192×86 mm footprint Includes M16x75L mounting bolts Consistent clamping for precision work The adjustable jaw set is designed to deliver stable, repeatable clamping, making it suitable for milling, turning and inspection fixtures where dimensional accuracy matters. The specified 1,800 kgf holding capacity ensures secure fixation of medium-duty workpieces, reducing micro-movement during machining and therefore lowering the risk of rework. The jaw geometry is optimised for even pressure distribution; this reduces part deformation and supports consistent tolerances across production runs. Technical terminology: clamp force refers to the static gripping force the jaws exert on a workpiece, given here in kilogram-force (kgf). Space-saving design that integrates easily With a compact footprint and a modest 11 kg mass, the jaw set is intended for straightforward integration into existing vises, fixtures or modular clamping systems. The small dimensions make it a practical choice where bench space or machine table real estate is constrained, while retaining robust performance. Installation is simplified by the supplied M16x75L mounting bolts, allowing direct attachment without additional fasteners. The compact design also contributes to faster set-up times and easier handling during tool changes or workshop reconfiguration. Practical benefits for workshop efficiency The construction emphasises practical maintenance and rapid adjustment. An adjustable mechanism enables quick adaptation to varying workpiece sizes without time-consuming changeovers, supporting higher throughput and lower setup costs per part. The durable build and straightforward geometry mean routine inspection and replacement cycles are simple to carry out, maintaining uptime in daily operations. The combination of secure holding, compact design and easy fastening aligns with the priorities of small to medium workshops and subcontractors seeking dependable clamping solutions. Contact Metav Werkzeuge for personalised advice on the Vertex SV-85 adjustable clamping jaws and to secure a reliable clamping solution matched to production needs; Metav Werkzeuge in Emmerich provides direct supply and expert consultation. Technical data Article number: SV-85 GTIN: 4061905087394 Manufacturer: Vertex Facts Dimensions: 86.5 x 192 x 86 mm Weight: 11 kg Clamp force: 1,800 kgf SKU: SV-85 Special features Adjustable clamping jaws Includes M16x75L mounting bolts Compact design for limited-space integration FAQ What clamping capacity does the jaw set provide? The jaw set offers a clamp force of 1,800 kgf, giving the SV-85 reliable holding for medium-duty machining and inspection tasks. Is the SV-85 suitable for compact machine tables? Yes, the compact dimensions of the SV-85 and its moderate weight make the jaw set suitable for integration on limited-space machine tables and fixtures. What is included for mounting? The delivery includes M16x75L mounting bolts to enable direct attachment of the jaw set without sourcing additional fasteners. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of the hard‑anodised aluminium construction, a 300 mm strip length and compatibility with 10 mm T‑slots to keep milling tables clean and accurate; supplied as a set of six for straightforward replacement. Order the VST‑10 directly via Metav Werkzeuge or ask our consultants for specification advice. VST-10 Cover for milling table slot — hard‑anodised aluminium, 300 mm set (Vertex) The VST‑10 is a set of slot covers designed to seal 10 mm milling table T‑slots, protecting workpieces and reducing swarf ingress while maintaining a low profile for versatile machining setups. Hard‑anodised aluminium construction Fits 10 mm milling table T‑slots 300 mm length per strip Supplied as set of 6 pieces Engineered protection that reduces machine downtime The VST‑10 strip covers offer reliable protection for T‑slot openings, helping to prevent chips and coolant from entering the table cavity and contaminating fixtures. Manufactured from hard‑anodised aluminium, the covers combine a low weight with surface hardness that resists abrasion and oxidisation; this reduces the frequency of cleaning cycles and lowers the risk of contamination‑related faults. For workshops where consistent setup and repeatability matter, these covers provide a simple, measurable improvement to process reliability. Fast fit and predictable compatibility for standard tables Designed for a slot width of 10 mm, the covers slide into common T‑slot geometries to create a stable closure without additional modifications. Their 300 mm length balances coverage and flexibility, allowing long runs to be covered continuously or cut-to-fit where shorter sections are required. Because the profile matches standard table dimensions, the replacement and retrofitting process is straightforward, which supports efficient maintenance planning and keeps machine availability high. Durable material and maintenance benefits explained The hard‑anodised aluminium construction gives a durable surface finish that is corrosion resistant and easy to clean; routine wiping restores appearance and function quickly. The lightweight nature — total mass recorded at 0.1 kg — minimises additional load on fixtures while still providing structural stability. In practice, the surface hardness reduces scuffing from fixtures and tooling, extending both the life of the cover strips and the cleanliness of the work area, which translates into lower long‑term operational effort. Versatile workshop use and practical advantages Supplied as a set of six, the covers suit production benches, jobbing shops and educational workshops where quick replacement and modularity are helpful. By closing exposed slots, the strips reduce the chance of small parts or chips falling into the table void and damaging internal components or measuring fixtures. The straightforward design supports a tidy workplace and helps preserve the accuracy of fixturing systems, making these covers a pragmatic addition to any milling setup that values uptime and component protection. For tailored advice on integrating the Vertex VST‑10 into existing equipment and prompt supply from Metav Werkzeuge, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — quote SKU VST‑10 for fast handling. Technical Data Article number: VST-10 GTIN: 4061905083525 Name: Cover for milling table slot (VST-10) Facts Length: 300 mm Height: 8 mm Weight: 0.1 kg Pieces per set: 6 Compatible slot width: 10 mm Special features Material: hard‑anodised aluminium ECLASS: 21189223 Brand: Vertex Supplied as a set FAQ What slot width is the cover designed for? The covers are intended for a 10 mm slot width; the VST‑10 by Vertex fits standard 10 mm T‑slot dimensions to ensure a secure profile match. Can the covers be cut to length on site? Yes, the 300 mm strips can be shortened to fit specific table layouts; the VST‑10 set is supplied as six pieces to allow modular coverage and easy customisation. How resistant is the surface to coolant and chips? The hard‑anodised aluminium finish of the VST‑10 provides good resistance to coolant exposure and abrasive swarf, simplifying cleaning and reducing surface wear over time. Are these covers suitable for heavy‑duty production environments? Supplied as a robust aluminium profile, the VST‑10 set is suitable for many production applications where slot protection reduces contamination and supports consistent fixturing. Does the VST‑10 affect fixturing or clamping accuracy? When correctly installed in a 10 mm T‑slot, the covers maintain a low profile and do not interfere with standard clamping operations; they help keep fixture surfaces cleaner, supporting repeatable setups. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of a compact solution that combines precision, straightforward integration and robust handling for more consistent slotting operations; the VSH-8C slotted bar (8 mm, 210 mm) supports stable setups while keeping changeover efficient. Order or request tailored advice via Metav Werkzeuge to ensure optimal fit for production workflows. VSH-8C Slotted Bar 8 mm — Accessory for precision slotting head, 210 mm The VSH-8C is a slotted bar designed as an accessory for precision slotting heads, intended to provide consistent alignment and a compact connection for 8 mm engagements in workshop and industrial slotting applications. 8 mm engagement for standard slotting interfaces 210 mm overall length for extended reach Robust handling weight of 0.8 kg Compatible with precision slotting head assemblies Secure positioning and measurable accuracy for slotting set-ups The slotted bar is engineered to offer repeatable alignment in slotting operations, translating into fewer setup iterations and improved process reliability. With an 8 mm engagement and an overall 210 mm length, the component permits precise placement while maintaining a compact footprint. For shops aiming to reduce rework and improve cycle-time consistency, this accessory provides a measurable improvement in fixture accuracy by stabilising the slotting head interface. Reduced set-up time and dependable handling in routine work By combining a deliberately balanced mass with a compact profile, the bar delivers stable handling during assembly and operation. The specified 0.8 kg mass helps to damp small vibrations and supports steady manual handling when mounting or removing the accessory. This contributes to fewer alignment checks between operations and a smoother workflow, especially in environments where frequent tool changes are required for varied slotting tasks. Straightforward integration with existing slotting heads and maintenance regimes The component is intended for direct use with precision slotting heads that accept an 8 mm slotted element; the design emphasises compatibility and uncomplicated integration into existing fixtures. The straightforward geometry makes inspection and routine maintenance simple, reducing downtime for cleaning or replacement. Where questions about fitment or technical details arise, clear specification of the VSH-8C and the host slotting head model enables rapid confirmation of compatibility. Contact Metav Werkzeuge today for compatibility guidance and a tailored supply recommendation for the Vertex VSH-8C slotted bar to support precise and reliable slotting set-ups Technical data SKU: VSH-8C GTIN: 4061905095245 ECLASS: 21040713 Core measurements Length: 210 mm Weight: 0.8 kg Designs & special features Accessory for precision slotting head Type: Slotted bar, 8 mm engagement Brand: Vertex FAQ What are the exact dimensions of the slotted bar? The VSH-8C has an overall length of 210 mm and an 8 mm engagement; the listed mass is 0.8 kg. Which slotting heads is the slotted bar compatible with? The slotted bar is designed for precision slotting heads that accept an 8 mm slotted element; compatibility depends on the host clamping geometry and should be verified against the host head's interface. Is the VSH-8C suitable for repetitive industrial use? The VSH-8C is a workshop-grade accessory by Vertex intended to provide stable positioning and handling in routine slotting operations. How is the slotted bar secured to the slotting head? The slotted bar provides a standard 8 mm engagement for mechanical clamping systems used by precision slotting heads; the exact securing method follows the host head's clamping procedure. Does the product include standard classifications or identifiers? Yes, the VSH-8C is listed with GTIN 4061905095245 and ECLASS 21040713 for identification and procurement processes. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Achieve reliable right‑angle set‑ups and secure workholding with the combination of high‑strength cast steel construction, a balanced mass of 7.4 kg and precise machined faces; these features translate into repeatable alignment and reduced rework. Order the VR-80 angle plate directly via Metav Werkzeuge or ask our consultants for application advice. VR-80 Angle Plate by Vertex — high‑strength cast steel, 7.4 kg The VR-80 angle plate is a compact clamping angle designed as a stable right‑angle reference for machining, inspection and assembly tasks in metalworking and toolmaking. High-strength cast steel construction Stable right-angle reference surface Compact footprint, 7.4 kg mass Consistent alignment for precision machining The VR-80 serves as a dependable right‑angle datum, delivering repeatable positioning for milling, drilling and inspection operations. Machined faces provide a true planar reference that reduces set‑up variation; this leads to fewer adjustments during batch runs and a lower scrap rate. The combination of a dense mass and robust casting minimises vibration and improves cutting stability, which is particularly beneficial when working with sensitive geometries or finishing passes. Where exact perpendicularity is required, the angle plate functions as a simple, low‑risk solution to maintain machining tolerances and throughput. Integrates smoothly into existing workholding setups With a compact footprint and straightforward mounting options, the device slips easily into existing fixture layouts and vice systems. The supplied dimensions (8x5x6") and a mass of 7.4 kg balance portability with form stability, enabling quick repositioning on the machine table while keeping the reference surface rigid under clamp loads. Flat, machined faces allow direct clamping or use with parallel bars and angle clamps, reducing set‑up time. For workshops aiming to streamline operations, this component supports faster job changeovers and consistent part orientation without the need for complex jigs. Built to last with low maintenance demands Constructed from high‑strength cast steel, the angle plate resists distortion and offers strong wear characteristics for extended service life. The material choice provides a corrosion‑resistant base suitable for general workshop environments; periodic cleaning and a light protective coating are sufficient to maintain the accuracy of the reference faces. This durability translates to long‑term cost efficiency: fewer replacements, reduced downtime and sustained precision across many production cycles. For quality‑focused facilities, the robustness of the design supports dependable measurement and machining practices. Contact Metav Werkzeuge for tailored advice, delivery options and to secure the VR-80 angle plate from our Emmerich warehouse, where product selection is curated for European industry standards. Technical Data Article number: VR-80 GTIN: 4061905093784 Manufacturer: Vertex Facts Material: high-strength cast steel Weight: 7.4 kg Dimensions: 8x5x6" ECLASS: 21020601 Special features Machined right-angle faces Compact workholding footprint Suitable for milling, drilling and inspection FAQ How is the VR-80 mounted on a machine table? The VR-80 angle plate is clamped using standard machine‑table clamps or mounted alongside vises and support blocks; its machined faces permit direct clamping or use with parallel bars. What materials is the angle plate suitable for use with? The VR-80 supports workholding for a wide range of materials in machining contexts; the high‑strength cast steel body ensures stability when processing metals and engineering plastics. How does the weight of 7.4 kg affect performance? A mass of 7.4 kg improves vibration damping and cut stability, helping maintain precision during milling and finishing operations without being so heavy as to hinder repositioning. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Angle plate VR-88 — high-strength cast steel, ±0.01 mm accuracy (Vertex) An Angle plate VR-88 engineered for precision fixturing, inspection and machine setup in industrial workshops. *High-strength cast steel construction *Accuracy 0.01 mm for precise setups *Robust 15.2 kg mass for stability *Compact 8 x 8 x 8" footprint Measurable precision that reduces rework and inspection time The Angle plate VR-88 delivers a certified ±0.01 mm level of accuracy, which translates into consistent reference faces for inspection and setup tasks. Such precision reduces measurement scatter and the need for repeat checks, enabling faster quality decisions on the shop floor. For users unfamiliar with tolerance terminology: ±0.01 mm means the plate maintains its reference plane within one hundredth of a millimetre, supporting tight inspection limits and reliable component alignment. Mass and material that improve clamping stability A mass of 15.2 kg combined with high-strength cast steel construction gives the fixture inherent damping and resistance to movement under clamping forces. The increased inertia lowers vibration transfer during machining and provides a rigid datum when using surface plates or portable metrology equipment. The benefit is fewer positional shifts during set-up, which leads to better first-pass yields and reduced cycle interruptions for rework. Small footprint, flexible placement and consistent shop performance The compact 8 x 8 x 8" footprint suits confined benches and inspection benches while still offering full-face clamping capability. The robust design supports a range of workshop tasks from routine inspection to final assembly fixturing, creating a versatile reference tool for both production and quality departments. Metav Werkzeuge’s role as a European quality filter ensures the component arrives ready for industrial use, backed by dependable supply and technical guidance. Contact Metav Werkzeuge to discuss how the Vertex angle plate VR-88 can enhance fixture stability and measurement reliability; specification advice and rapid supply from Emmerich are available by e-mail or phone Technical Data Article number: VR-88 GTIN: 4061905091056 Eclass: 21170130 Facts Accuracy: 0.01 mm Weight: 15.2 kg Dimensions: 8 x 8 x 8" Materials / Special features Material: High-strength cast steel Suitable for inspection and fixturing Robust, vibration-damping design FAQ What level of accuracy does this plate provide? The Angle plate VR-88 provides an accuracy of 0.01 mm, offering a reliable datum for precise inspection and setup work. Is the VR-88 suitable for machining fixturing as well as inspection? Yes, the Vertex VR-88 is designed for both fixturing and inspection; its cast steel construction and mass make it suitable for stable clamping during light machining operations. How heavy is the plate and how does that affect use? At 15.2 kg the plate provides stability and vibration damping for more consistent measurement and clamping results without excessive handling for standard inspection benches. Can the plate be used on small benches and mobile inspection rigs? The compact 8 x 8 x 8" footprint allows placement on smaller benches and mobile rigs while still delivering full-face support for components during measurement tasks. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of the 9 W LED energy efficiency and the IP67-protected light head for reliably bright, low-heat illumination in demanding workshop environments; the compact 220×220 mm arm and included 1.8 m cable make installation and immediate use straightforward — order directly via Metav Werkzeuge or ask our consultants for tailored advice. VLED-400M workshop inspection lamp by Vertex — 9 W LED, IP67 light head The VLED-400M is a waterproof inspection lamp designed for machine and workshop lighting, offering low-energy LED illumination and a compact square arm for targeted task lighting. 9 W LED for energy-efficient illumination Light head rated IP67 for wet environments Compact 220×220 mm square arm for precise positioning Includes 1.8 m cable for immediate installation Reliable illumination where accuracy matters The inspection lamp delivers steady LED light that supports close visual work without the high temperatures associated with older halogen solutions. With a rated output of 9 W, the lamp head provides efficient, continuous illumination that improves visibility on fine details and reduces operator fatigue during lengthy tasks. The low power draw also helps maintain a cooler work environment near sensitive components, contributing directly to process reliability and operator comfort. Durable protection for the lamp head, clear limits for the arm The light head is IP67-rated, meaning the illumination unit is protected against dust ingress and temporary immersion — a significant advantage when coolant splashes or wet-cleaning cycles occur. The supporting arm carries an IP20 rating, which highlights that while the lamp head is sealed against moisture, the arm is intended for use in standard workshop atmospheres rather than submerged or continuously wet conditions. This distinction allows confident placement of the fixture where protection is needed most, while clarifying suitable mounting scenarios. Voltage compatibility and practical on-site readiness Electrical compatibility with 110–220 V mains permits straightforward integration across varied supply networks, avoiding the need for custom transformers in many installations. The lamp is supplied with a 1.8 m cable, enabling immediate connection and flexible routing to nearby power sources. The relatively compact form and weight of 1.96 kg support secure mounting on machine guards, benches or stands without excessive strain on fixtures, making the unit a practical choice for retrofit and new-equipment setups alike. Designed for workshop use and straightforward procurement The fixture’s square 220×220 mm arm gives precise positioning for focused tasks such as inspection, assembly or maintenance checks. Classified under ETIM and ECLASS identifiers, the product supports structured procurement and integration into parts lists and inventories. The lamp is available in LED or halogen variants, allowing selection according to lighting preference and application needs. Supplied ready to install with cable, the unit reduces commissioning time and simplifies stocking for facilities managers. For reliable workshop lighting from a recognised brand, contact Metav Werkzeuge to discuss the Vertex VLED-400M and receive expert guidance and swift delivery from our Emmerich warehouse — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VLED-400M GTIN: 4061905088414 Manufacturer: Vertex Facts Power supply: 110V/220V Light output: 9 W (LED) Arm size: 220×220 mm (square) Weight: 1.96 kg Special features Light head IP67, arm IP20 Available in halogen or LED versions Included accessory: Cable 1.8 m Classified: eClass 27110640, ETIM EC001959 FAQ Is the light head fully waterproof and suitable for wet-cleaning? The light head is rated IP67, so temporary immersion and splash-prone cleaning are supported; the arm, however, is IP20 and should not be submerged. Can the lamp be used on both 110 V and 220 V supplies? Yes, the unit supports 110–220 V operation, making the lamp compatible with common mains voltages in most regions. What cable length is supplied and is the lamp ready to install? The lamp is supplied with a 1.8 m cable, enabling immediate connection and straightforward installation without additional cabling. Is there a halogen option as well as the LED version? The product range includes halogen or LED versions; the LED variant offers 9 W efficiency and lower operating temperatures compared with halogen. Which Vertex model should be specified for procurement lists? Specify the VLED-400M SKU and GTIN 4061905088414 to ensure correct ordering of the LED inspection lamp from Vertex. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

VLED-500S — Vertex waterproof LED work lamp, IP67, 9 W The VLED-500S is a robust, compact work lamp for industrial and workshop use, delivering splash‑proof illumination and flexible positioning for detailed assembly and inspection tasks. IP67 protection against dust and water 9 W LED for energy-efficient light 110V/220V dual-voltage compatibility Supplied with 1.8 m cable Consistent, bright light for precision work The VLED-500S provides reliable, shadow‑reducing illumination that supports accurate measurement and fine assembly. With a 9 W LED light source, the lamp produces steady, colour‑stable illumination while consuming minimal energy; this reduces heat generation and extends service intervals compared with filament options. The high ingress protection (IP67) ensures light output remains consistent even in dusty or wet production environments, contributing to fewer process interruptions and a measurable reduction in rejects during visual inspection tasks. The lamp’s compact form factor and low thermal footprint make it suitable for close‑up workbenches and machine‑tended inspection stations. Flexible mounting and targeted positioning for varied setups Designed with a single‑joint round arm, the lamp allows simple, repeatable repositioning for task‑specific illumination, from soldering and inspection to tool setting. The unit operates on 110V/220V supplies, enabling use across different regions and on mobile equipment without additional transformers. A 1.8 m cable is included, supporting easy integration into existing workstations and minimising the need for immediate rewiring. The combination of adjustable positioning and universal voltage support makes the lamp an adaptable asset for maintenance teams and production lines that require quick reconfiguration and minimal downtime. Durable construction that supports operational reliability Constructed for the workshop environment, this LED work lamp balances portability and robustness at 1.6 kg; it is simple to move yet substantial enough to remain steady during adjustment. The IP67 rating certifies protection against dust ingress and temporary immersion in water, offering tangible safety and compliance benefits in harsh or washdown conditions. Long service life of the LED module and the lamp’s sealed design reduce maintenance cycles and spare‑parts logistics, helping to lower total cost of ownership while maintaining safe, well‑lit work areas. Sourcing through an experienced distributor further improves supply reliability for production planners and procurement teams. Contact Metav Werkzeuge in Emmerich for expert advice on integrating the VLED-500S into existing workstations and for prompt, reliable dispatch from our European stock Technical Data Article number: VLED-500S GTIN: 4061905005725 Protection class: IP67 Light output: 9 W (LED) Voltage: 110V/220V Weight: 1.6 kg Included accessory: Cable 1.8 m Arm: Single‑joint (round) Facts Weight: 1.6 kg Power: 9 W (LED) Voltage range: 110V/220V Cable length: 1.8 m Special features Waterproof design Single‑joint round arm for targeted positioning Supplied cable 1.8 m Brand: Vertex FAQ Is the VLED-500S suitable for wet environments? Yes. The VLED-500S carries an IP67 rating, which provides protection against dust ingress and temporary immersion in water, making the lamp suitable for washdown and splash‑prone areas. What voltage supplies does the lamp accept? The VLED-500S supports 110V/220V operation, enabling flexible use across different installations and regions without an external converter. Does the lamp come ready to install? The lamp is supplied complete with a 1.8 m cable, allowing immediate connection to the mains and straightforward mounting via its adjustable arm. How does the LED compare to halogen in workshop use? The LED version offers longer service life, lower heat emission and reduced energy consumption compared with halogen alternatives; the VLED-500S’s sealed LED module also requires less maintenance. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Robust IP67 protection combined with a low-energy 9 W LED and dual-voltage operation ensures dependable illumination in wet or dusty workshop environments; the integrated 1.8 m cable and compact arm simplify installation and reduce downtime. Order the VLED-500M through Metav Werkzeuge or consult the technical team for detailed specifications. VLED-500M LED Work Lamp by Vertex — IP67 waterproof, 9 W The VLED-500M is a compact, waterproof work lamp intended for industrial and workshop use, offering flexible supply voltages and a sturdy mounting arm for localised task lighting. IP67 waterproof protection 9 W LED energy efficiency Dual voltage 110V/220V compatibility Includes 1.8 m cable Durable illumination for harsh conditions The lamp’s IP67 rating guarantees resistance to dust and temporary immersion, making it suitable for wet production halls and outdoor workstations where resilience matters. Constructed for continuous operation in challenging settings, this lighting solution combines a sealed housing with a compact profile so that maintenance intervals are extended and unplanned downtime is reduced. The robust build supports reliable performance in environments that demand consistent, protected illumination. Low power consumption with wide voltage range Equipped with a 9 W LED module and compatible with 110V/220V mains, the unit delivers energy-efficient task lighting while remaining simple to integrate into different supply systems. The LED source minimises heat generation and offers longer service life compared with traditional lamps, which reduces replacement frequency and operating costs. This technical combination provides a practical balance of efficiency and performance for sustained workshop use. Simple installation and flexible mounting The lamp is supplied with a 1.8 m cable and fitted to a 220 x 220 mm rounded arm, enabling straightforward positioning above benches or machines without complex wiring. With a weight of 2.3 kg, the luminaire is heavy enough to remain stable yet light enough for safe handling during installation or repositioning. The included cable length and compact arm dimension favour rapid setup, lowering downtime during assembly or equipment changes. Trusted supply chain and reduced procurement risk Sourced from a recognised manufacturer and distributed via a specialist partner, this lighting solution benefits from a quality filter that supports consistent product standards and reliable availability. Metav’s role as a precision partner ensures items reach European workshops with transparent logistics and an established reputation; the company’s broad catalogue and longstanding customer base reflect a commitment to dependable supply and technical competence. Choose the Vertex VLED-500M for dependable IP67 workshop lighting — contact Metav Werkzeuge in Emmerich for specification support and availability Technical Data SKU: VLED-500M GTIN: 4061905005749 Type: Lampe Brand: Vertex Protection class: IP 67 Facts Power supply: 110V/220V Light output: 9 W (LED) Arm size: 220 x 220 mm (round) Cable length included: 1.8 m Weight: 2.3 kg Special features Waterproof Variants: Halogen or LED Supplied accessory: Cable 1.8 m FAQ What environments is this lamp suitable for? The VLED-500M by Vertex is designed for workshops and industrial areas where IP67 protection against dust and temporary immersion is required. Can the lamp be used with different mains supplies? Yes, the unit supports 110V/220V operation, allowing deployment across sites with varying supply voltages. Is the cable included and what length is it? The Vertex VLED-500M is supplied with a 1.8 m cable, simplifying installation at typical workbench heights. How heavy is the luminaire and does it require special mounting? The luminaire weighs 2.3 kg, enabling secure mounting on standard arms such as the supplied 220 x 220 mm rounded bracket without heavy-duty fixings. Are halogen options available alongside the LED version? The product range includes halogen or LED variants; the listed model features a 9 W LED light source. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Secure clamping with compact dimensions and compatible thread options ensures efficient fixture set-up and repeatable positioning on machine tables. Combine the 9/16" T-slot compatibility with a lightweight single-piece design for reliable, low-maintenance operation. Order directly via Metav Werkzeuge or consult our specialists for further technical clarification. 3414I T-slot nut by Vertex — 9/16" T-slot, compact dimensions The 3414I is a T-slot nut designed to secure fixtures and clamps in 9/16" T-slots, providing a straightforward solution for machine tables and modular fixturing. T-slot 9/16" compatible Compact dimensions 7/8×1-1/8×5/8" Single-piece design Lightweight: 0.048 kg Secure clamping for precise setups A T-slot nut is the fundamental interface between a workholding element and the machine table. With the 9/16" T-slot compatibility and the compact external dimensions, this fastener delivers a secure connection for clamps and locators while keeping the clamping assembly low-profile. The reduced mass, at 0.048 kg, helps to simplify handling and positioning during frequent tool changes and fixturing operations, which in turn improves throughput and reduces set-up time in serial production. Faster assembly, fewer complications The single-piece construction and defined thread options mean straightforward installation and repeatable results. Threaded options are supplied as stated, supporting standard clamping hardware and enabling consistent torque transfer to the clamping element. This reduces the likelihood of movement under load and minimises rework. For workshops that prioritise efficiency, the predictable fit and stable retention characteristics translate into fewer interruptions and more reliable machining cycles. Confidence from established supply and stock reliability Sourced from Vertex, this fastener benefits from a focused manufacturing standard and traceable SKU control, giving procurement teams clarity when integrating components into production supplies. Delivered via a specialist supplier, stock is picked and inspected in Emmerich to act as a quality filter for the European market, supporting continued availability and consistent product quality across repeat orders. Contact Metav Werkzeuge today for expert advice on integrating the Vertex 3414I T-slot nut into existing fixturing systems and to arrange prompt supply from our Emmerich stock Technical data Article number: 3414I GTIN: 4061905092596 Manufacturer: Vertex Facts Weight: 0.048 kg Dimensions: 7/8×1-1/8×5/8" T-slot width: 9/16" Thread: 1/2-12" and 1/12-13" Special features Single-piece T-slot nut Designed for fixture and clamp attachment Model family: 3414I FAQ Is this compatible with standard 9/16" T-slots? Yes. The 3414I T-slot nut is specified for 9/16" T-slots and is intended for securing clamps and fixtures within that slot dimension. Which thread sizes are provided? The product data lists thread options as 1/2-12" and 1/12-13", which are supplied as stated in the technical information for the Vertex 3414I. What material is the nut made of? Material information is not specified in the provided data for this item; material details should be requested if required for a specific application. Can this fastener be used for modular fixturing on milling tables? Yes. The T-slot nut is intended for machine table fixturing and offers a low-profile clamping interface suitable for milling and general fixture applications. What is the article number and weight for inventory purposes? Article number (SKU) is 3414I and the weight is 0.048 kg as documented in the product specifications. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of secure clamping in standard T-slots together with fast, repeatable assembly thanks to the 3/8-16″ threaded interface and compact dimensions; the result is reduced setup time and reliable part location on machine tables. Order the component directly via Metav Werkzeuge or ask our consultants for compatibility advice. Vertex T-slot nut 3433I — 9/16″ T-slot, 3/8-16″ thread The Vertex T-slot nut 3433I is a compact clamping element designed for use in machine table T-slots and fixtures, providing a robust threaded connection for workholding and accessory mounting. Compatible with 9/16″ T-slots 3/8-16″ threaded connection Lightweight 0.048 kg body Single-piece design for stable clamping Precise fit for standard machine tables The 9/16" T-slot dimension ensures direct compatibility with common machine tables and clamping systems used in workshops and production lines. The standardised profile delivers repeatable positioning, reducing time spent on alignment and adjustments. With a 3/8-16″ thread, the component mates with widely used bolts and studs, simplifying inventory management for fastening hardware and avoiding special-order parts. This compatibility supports faster set-ups and a smoother production flow, which is particularly relevant in batch manufacturing and jigs where every minute saved improves throughput. Small, robust and easy to handle At approximately 0.048 kg, the fastener is light enough for efficient handling yet stable during clamping procedures. The compact geometry, given as 7/8 x 1-1/8 x 5/8″, allows installation in confined slots without obstructing adjacent fixtures. The single-piece construction reduces potential points of failure and is suitable where a straightforward, low-maintenance solution is required. For operators and supervisors this means fewer replacement parts and predictable behaviour under normal workshop loads, contributing to consistent process quality. Practical in varied workshop scenarios This clamping element performs well across general machining and assembly tasks: it secures workpieces, supports jigs and holds fixturing accessories. The standardised thread and slot dimensions make the part useful in retrofit projects and when expanding existing clamping fixtures. Because the design avoids specialised interfaces, workshop planners can standardise on familiar fasteners and reduce the number of different spare parts needed at the bench, simplifying logistics and costing models in smaller operations as well as larger production sites. Reliability and traceability for professional use The component conforms to common industrial sizing, making specification and procurement straightforward. The simple, well-documented geometry supports planning, quality assurance and traceability in procurement records. Where part identification is required, the SKU 3433I and GTIN are available for accurate ordering and stock control. Combining established dimensions with consistent manufacturing tolerances helps reduce the risk of misfits and the time lost to trial-and-error adjustments on the shopfloor. Arrange procurement through Metav Werkzeuge for reliable supply and expert advice on integration into existing fixturing systems Technical data Article number: 3433I GTIN: 4061905091988 Weight: 0.048 kg Dimensions: 7/8x1-1/8x5/8" Facts T-slot size: 9/16" Thread: 3/8-16" ECLASS: 21029107 Special features Single-piece unit Brand: Vertex Suitable for standard machine table T-slots FAQ What T-slot size does the fastener fit? The fastener fits a 9/16" T-slot; this standard dimension ensures the part seats correctly in common machine table grooves. Which thread is used for bolting to the nut? The component uses a 3/8-16" thread, compatible with standard imperial bolts and studs for secure clamping. Is the item suitable for retrofitting existing fixtures? Yes, the geometry and thread standard make the part suitable for retrofit work where standard T-slot fasteners are required. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of high continuous torque and flexible supply options to maintain steady production while reducing changeover time. The combination of 200 ft‑lb torque, 3,000 rpm capability and a nominal 90 psi / 6.3 kg/cm² air feed supports reliable, repeatable fastening and tensioning operations. Order the pneumatic tension rod directly via Metav Werkzeuge or consult Metav's specialists for application advice. Pneumatic Tension Rod (PD-200-NT50) — 200 ft‑lb torque, 3,000 rpm, Vertex Pneumatic Tension Rod (PD-200-NT50) is an air‑operated tensioning unit for industrial assembly and fastening tasks, designed to deliver consistent torque and rapid cycle rates for production environments 200 ft‑lb torque for heavy-duty fastening High-speed operation: 3,000 rpm Nominal air supply 90 psi / 6.3 kg/cm² Supply options AC 110/220 V and DC 24 V Consistent torque for precise assembly The unit delivers 200 ft‑lb torque, enabling secure fastening and reliable clamping force where reproducibility matters. Torque is the turning force applied at the tool output; specifying a constant torque reduces rework and improves joint integrity. The design is focused on repeatability: the mechanical output is stabilised by the air drive and gearing, which means fewer torque variations in serial processes. The combination of robust torque and controlled actuation reduces assembly errors and supports quality assurance protocols in manufacturing lines. Fast cycle rates with industrial air and electrical options High throughput is supported by a maximum speed of 3,000 rpm, which allows rapid tightening cycles and short takt times in automated or semi-automated lines. The unit operates from a nominal 90 psi / 6.3 kg/cm² compressed‑air supply and accepts multiple electrical feeds (AC 110V, 220V or DC 24V) for control electronics or integrated sensors. These characteristics make the product suitable for integration with PLC systems and pneumatic manifolds. A compact overall mass of 11 kg keeps handling and fixturing requirements moderate while preserving rigidity during operation. Designed for industrial workflow and straightforward integration Built by Vertex and identified as PD-200-NT50, this tension rod is intended for continuous industrial use where durability and serviceability are required. The drive is engineered to be mounted within assembly fixtures or on tool balancers; electrical and pneumatic interfaces are standardised to ease commissioning. Maintenance is simplified by accessible connection points and replaceable wear components, which supports predictable uptime and planned servicing. Compatibility with common factory supplies and control systems reduces installation complexity and streamlines adoption into existing production cells. Contact Metav Werkzeuge for availability, tailored delivery options and technical matching of Vertex pneumatic tension rods — refer to PD-200-NT50 when enquiring and benefit from Metav's local stock and application consultancy. Technical Data SKU: PD-200-NT50 GTIN: 4061905092282 Manufacturer: Vertex eClass: 23309104 Core Specifications Torque: 200 ft‑lb Speed: 3,000 rpm Air pressure: 90 psi / 6.3 kg/cm² Weight: 11 kg Supply voltage: AC 110V / 220V, DC 24V Special features Air‑operated tensioning unit Designed for integration with PLC control Compact, serviceable construction Suitable for repetitive industrial assembly FAQ What applications is this tension rod suitable for? This pneumatic tension rod by Vertex (PD-200-NT50) is suitable for industrial assembly and fastening tasks requiring consistent torque and rapid cycle times. What air and electrical supplies are required? The unit requires a nominal air supply of 90 psi / 6.3 kg/cm² and accepts AC 110V or 220V or DC 24V for control interfaces. How does the specified torque relate to fastening quality? The 200 ft‑lb torque rating indicates the maximum consistent turning force; using the PD-200-NT50 at the specified torque improves joint reliability and reduces the risk of under‑ or over‑tightening. Is the unit ready for PLC integration? Yes, the PD-200-NT50 is designed with standard electrical and pneumatic interfaces to facilitate integration with PLCs and automated control systems. What maintenance is recommended to ensure long service life? Regular inspection of pneumatic seals and drive components, adherence to filtered and lubricated air supply specifications, and scheduled replacement of wear parts will maintain performance of the Vertex tension rod. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Technische Daten: Bezeichnung: Kopf Vollhartmetall Durchmesser: 138 mm bis 190 mm Geeignet für: Bohrkopfdurchmesser 85,725-86mm (Typ NT) oder Bohrkopfdurchmesser 85,725/100/105/110/115mm je nach Ausführung Gewicht: 12,5 kg - 18 kg Geschwindigkeit: Max. 2000r.p.m. Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Das ist der Hersteller in einigen Worten: Seit 1978 ist VERTEX der größte Hersteller für Maschinenteile in Taiwan. Mit einer beeindruckenden Produktionsfläche von über 15000 m² ist VERTEX in der Lage, große Mengen hochwertiger Maschinenteile herzustellen, um den Bedürfnissen der Kunden gerecht zu werden. Das Unternehmen hat sich auf Forschung und Entwicklung spezialisiert und ist stets bestrebt, innovative Designs zu entwickeln. Die hohe Lagerverfügbarkeit von 98% aller Artikel stellt sicher, dass die Kunden schnell und effizient bedient werden können. VERTEX hat sich einen hervorragenden Ruf aufgebaut, indem es qualitativ hochwertige Produkte liefert und gleichzeitig erstklassigen Kundenservice bietet. VERTEX ist der vertrauenswürdige Partner für Maschinenteile in Taiwan.

Take advantage of the axial drive and smooth jaws to achieve consistent clamping and reduced part marking in small workpieces; the compact footprint and low weight ensure simple handling and integration with existing chucks. Order the unit via Metav Werkzeuge or consult the Metav team for tailored advice. VNC-4AD — Vertex axial drive with smooth jaws (for VNC-FV) VNC-4AD is an axial-drive accessory with smooth jaws for the VNC-FV chuck, designed to deliver repeatable clamping for delicate and precision components in workshop environments. Compact 98x76x45 mm footprint Smooth jaws for delicate components Axial drive for consistent clamping force Lightweight 1.57 kg for easy handling Consistent clamping that reduces rework The combination of an axial drive mechanism and smooth jaws delivers a reproducible clamping action that reduces variation between cycles. By transferring axial movement directly into the jaw travel, the unit avoids lateral play common with some rotary-driven systems, resulting in precision clamping and fewer setup readjustments. For production runs where small deviations lead to scrap or additional machining, this ensures processes remain efficient and predictable. Compact design for tight fixtures and quick changeovers With a compact footprint of 98 x 76 x 45 mm and a mass of 1.57 kg, the unit fits into constrained spindle or fixture spaces without substantial modification. Its form factor supports quick integration into existing VNC-FV setups and minimises the need for additional fixturing. The small size also helps to streamline handling during tool changes, supporting faster changeovers and reducing downtime between operations. Gentle handling of sensitive parts for higher yield The smooth jaws provide a non-marking contact surface that is particularly suited to finished or soft materials. Where aesthetics or surface integrity matter, avoiding serrated clamping faces prevents indentation and subsequent rework. The axial actuation delivers a controlled closing action that spreads the clamping force evenly, helping to protect fragile components while maintaining sufficient retention for subsequent machining or inspection steps. Compatibility and workshop applicability Designed specifically as an accessory for the VNC-FV range, the device integrates with established clamping workflows and supports applications in precision engineering, small-batch manufacturing and specialist repair shops. Its straightforward mechanical principle makes it accessible to technicians with basic clamping knowledge while offering the repeatability required by more exacting quality processes. For operations seeking to standardise fixture behaviour, the unit forms a compact and reliable component of a consistent clamping strategy. Choose the Vertex VNC-4AD for dependable axial clamping and contact Metav Werkzeuge in Emmerich for expert purchasing advice and specification guidance — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical Data Article number: VNC-4AD GTIN: 4061905084423 Shop title: Axialer Antrieb und glatte Backen Vertex einfach Online besorgen Facts Dimensions: 98 x 76 x 45 mm Weight: 1.57 kg eCl@ss: 21130302 Special features Axial drive actuation Smooth jaw faces for delicate parts Compatible with VNC-FV chuck systems Gallery image available (detail and main views) FAQ What materials can be clamped with this accessory? The VNC-4AD is intended for general workshop use and, with its smooth jaws, is especially suitable for delicate and finished workpieces where marking must be avoided. Is the VNC-4AD compatible with existing VNC-FV chucks? Yes — the unit is specified for use with VNC-FV systems and is designed to integrate mechanically with that chuck family. How does the axial drive improve repeatability compared with rotary actuation? Axial drive converts linear motion directly into jaw travel, reducing lateral play and delivering more reproducible jaw positions and consistent clamping force across cycles. Does the unit require specialised maintenance? Maintenance is limited to routine inspection of moving parts and jaw faces; the straightforward mechanical design simplifies upkeep and reduces downtime. Can this accessory be used in small-batch production environments? Yes — the compact size and repeatable clamping behaviour make it suitable for small-batch and precision manufacturing where fixture space is limited. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of a hardened L‑jaw design and a compact 99.5×64×35 mm footprint for secure, repeatable clamping in VQC vises; order the unit directly via Metav Werkzeuge or consult our specialists for application advice. VQC-100MJL Hard L‑Jaws for VQC Vises — Hardened Clamping, Compact Dimensions (Vertex) The VQC-100MJL is a hardened L‑jaw set developed for VQC series vises to provide secure, repeatable clamping for machining and inspection tasks. Hardened steel design for wear resistance Precision fit for VQC series vises Compact 99.5×64×35 mm footprint Stable clamping weight 1.15 kg Consistent clamping for repeatable machining The hardened L‑jaw set delivers consistent clamping force that reduces part movement and improves machining outcomes. Manufactured for durability, the jaw geometry maintains contact accuracy across repeated cycles, which lowers scrap rates and shortens setup time. The compact dimensions (99.5×64×35 mm) and moderate mass (1.15 kg) make the set easy to handle while preserving stiffness during milling, drilling and light grinding operations. This combination of rigidity and size supports workflows where both floor space and stability matter. Seamless integration with VQC vises for reliable setups Engineered specifically for the VQC series, the jaw profile and mounting surfaces are matched to the vise interface to ensure precise alignment and fast installation. Correctly fitted jaws reduce the need for ad‑hoc adjustments, enabling quicker changeovers between jobs and improving overall throughput. The hardened surface resists deformation under clamping pressure, maintaining repeatability over long production runs and contributing to predictable part tolerances. Durable construction to lower maintenance and downtime A wear‑resistant finish and robust construction extend service life and reduce the frequency of replacements. The design emphasises functional longevity rather than cosmetic features, so maintenance cycles are extended and workshop costs are contained. For shops standardising on VQC vises, the hardened L‑jaw set offers a dependable spare or upgrade that supports continuous operation and predictable scheduling — an advantage for both routine production and specialist tasks. For trusted clamping from Vertex and tailored advice from Metav Werkzeuge’s Emmerich team, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application suitability and supply options Technical Data Article number: VQC-100MJL GTIN: 4061905087387 Manufacturer: Vertex Facts Dimensions: 99.5×64×35 mm Weight: 1.15 kg Eclass: 21029107 Special features Hardened L‑jaw design For VQC series vises Stable clamping geometry Includes technical drawing in product gallery FAQ Are the jaws compatible with all VQC vise sizes? The jaw set is specified for the VQC series and fits the VQC interface as indicated; verify the vise model to ensure full compatibility with the VQC-100MJL jaw geometry. What materials are suitable for clamping with these jaws? The hardened construction of the VQC-100MJL makes it suitable for a wide range of workshop materials; avoid clamping delicate finishes without protective packing to prevent surface marking. How does the hardened surface affect long‑term precision? Hardened surfaces on the jaw set help retain the original contour under load, so the VQC-100MJL sustains repeatability and reduces wear-related variation over prolonged use. Is any special maintenance required? Regular inspection for burrs or chips and routine cleaning will preserve clamping performance; the durable finish minimises maintenance frequency compared with untreated jaws. Can the jaw set be used for inspection as well as machining? Yes — the stable contact and precise fit with VQC vises make the jaw set suitable for both machining setups and measurement tasks where positional repeatability is important. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of precise clamping and reliable workpiece protection combined with a compact footprint for consistent results in small setups. The compatibility with VQC vises and straightforward procurement via Metav Werkzeuge make these soft jaws a practical choice for workshops seeking repeatable, damage-free clamping. Order the accessory directly through Metav Werkzeuge or consult their advisors for application matching. VQC-100MJ Soft Jaws for VQC Vises — Compact 99.5×64×50 mm (Vertex) The VQC-100MJ soft jaws are a protective clamping accessory designed for use with VQC vises, offering a compact profile and repeatable contact surfaces for delicate or finished components Soft jaws for VQC vises Compact 99.5×64×50 mm footprint Weight 2.65 kg for stable clamping Protects workpiece during clamping Minimal footprint with clear protection benefits These soft jaws are manufactured to provide a gentle clamping surface that reduces marking on finished or delicate parts while retaining firm hold. The compact dimension of 99.5 x 64 x 50 mm makes the accessory suitable for confined workspaces and small fixtures, allowing secure support without occupying excessive jaw travel. For operations that require occasional protective clamping, the compact format helps maintain machine accessibility and keeps setups tidy. Stable contact and consistent set-up With a mass of 2.65 kg, the accessory contributes to stable clamping and reduced vibration during light-to-medium machining and inspection tasks. The design supports consistent positioning of the clamped part, which helps to shorten setup times and increases throughput in repetitive operations. Clamping stability is particularly relevant when handling sensitive components where surface finish and dimensional integrity must be preserved. Integration into workshop workflows for repeatable results Designed specifically for compatibility with VQC-style vises, the jaws allow straightforward replacement of standard steel faces to achieve non-marring contact and improved part handling. The geometry and contact surfaces are engineered to support repeatability, so once the clamping position is established, subsequent parts can be secured with the same reference, reducing adjustment cycles. For shops aiming to streamline fixture changes while protecting workpieces, this accessory integrates smoothly into existing clamping routines. For tailored clamping solutions from Vertex, request the VQC-100MJ soft jaws via Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for precise application advice Technical data Article number: VQC-100MJ GTIN: 4061905094750 Name: Soft jaws for VQC vises Dimensions: 99.5 x 64 x 50 mm Weight: 2.65 kg Compatibility: for VQC vises ECLASS: 21029107 SKU: VQC-100MJ FAQ What machines are these jaws designed for? The VQC-100MJ soft jaws are designed specifically for use with VQC vises and their compatible clamping systems, providing protective contact surfaces for delicate parts. Will these jaws prevent marking on finished parts? Yes, the VQC-100MJ accessory replaces harder jaw faces with softer contact surfaces to reduce marking and support gentler clamping of finished components. How does the compact size affect workshop use? The compact footprint of the jaws allows installation in confined setups and small fixtures while preserving jaw travel and machine accessibility. Are these jaws suitable for repeating the same setup reliably? The machined contact geometry of the VQC-100MJ supports repeatable positioning, helping to reduce setup time for batch or series work. Is the VQC-100MJ compatible with other brands of vises? Compatibility is specified for VQC vises; for cross-brand mounting options, consult Metav Werkzeuge to verify fitment and necessary adapters. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Take advantage of a hardened jaw profile and precision fit to improve clamping reliability and reduce setup time; order directly via Metav Werkzeuge or consult our specialists for compatibility advice. VQC-100FJL Hard L-jaws — precision clamping for VQC vises, hardened profile VQC-100FJL hard L-jaws designed for secure, repeatable clamping in workshop and light industrial environments, compatible with VQC vises. Hardened steel construction for long service life Precision-machined fit for VQC vises Compact dimensions: 99.5 x 73 x 35 mm Weighs 1.27 kg for stable clamping Improve clamping reliability and cycle time The hardened jaw geometry delivers a consistent grip on workpieces, reducing movement during machining and inspection. A precision fit to the vise dovetail and jaw housing minimises play, which translates into fewer workpiece resets and lower scrap rates. From a rational perspective, less rework and faster set-ups improve throughput: the combination of a hardened contact surface and exact mating faces supports steady clamping forces throughout repeated cycles, enhancing production reliability. Durable, precision-machined construction for dependable use Manufactured to tight tolerances, these L-jaws provide a precision-machined contact area that preserves part geometry and prevents marking. The compact footprint, 99.5 x 73 x 35 mm, together with a mass of 1.27 kg, creates a stable clamping interface suited to short-run and repetitive tasks. Compatibility with VQC vises ensures straightforward replacement of worn jaws, while the robust design contributes to long service intervals and predictable performance in everyday workshop use. Smooth integration into workshop workflows The L-jaw form factor simplifies fixture changes and supports diverse part geometries without complex fixturing. Being tailored for VQC vises, the jaws slot into established clamping routines and reduce the need for bespoke adaptations. Beyond efficiency, the solid build provides tactile reassurance at the bench: the result is a calmer, more controlled workflow where technicians can focus on machining quality rather than compensating for unstable clamping. For fast supply and precise compatibility checks on Vertex VQC-100FJL hard L-jaws, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to arrange immediate dispatch and expert advice Technical data SKU: VQC-100FJL GTIN: 4061905084331 Product name: Hard L-jaws Dimensions & weight Dimensions: 99.5 x 73 x 35 mm Weight: 1.27 kg ECLASS: 21029107 Compatibility & features For VQC vises Hardened L-jaw design Fast dispatch indicated in product description FAQ Are these jaws compatible with VQC vises? Yes. The VQC-100FJL hard L-jaws are designed specifically for use with VQC vises and match the standard jaw mounting geometry. Are the L-jaws hardened for durability? The product is specified as hard L-jaws, indicating a hardened contact surface to resist wear and maintain clamping performance over extended use. What are the exact dimensions and weight of the jaws? The jaws measure 99.5 x 73 x 35 mm and weigh 1.27 kg, providing a compact and stable clamping solution. Will these jaws reduce workpiece movement during machining? Yes. The precision-machined faces and hardened profile of the VQC-100FJL contribute to stable clamping and reduced part movement during operations. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Precision soft jaws built for stable, protective clamping: compact dimensions and a substantial mass combine to reduce workpiece marking and improve repeatability. Benefit from quick integration with Vertex VQC vises and confident handling of delicate components — order the VQC-100FJ via Metav Werkzeuge or consult the Metav team for compatibility advice. VQC-100FJ Soft Jaws for VQC vises — 99.5×73×50 mm, 2.97 kg (Vertex) The VQC-100FJ soft jaws are designed to provide protective, adaptable clamping for VQC vises in precision machining and assembly applications Compatible with VQC vises Compact 99.5×73×50 mm profile Weight 2.97 kg for stable clamping Increased protection for sensitive workpieces Soft-contact clamping provided by these soft jaws reduces surface damage and the need for secondary finishing. The compliant clamping faces distribute force more evenly than hard-steel jaws, lowering the risk of localised deformation during tightening. For operations where appearance or dimensional tolerances matter, this protection translates into fewer rejects and less rework, improving overall process yield and saving operator time. Compact footprint, greater bench flexibility The small external dimensions of 99.5×73×50 mm make these jaws suitable where space is limited or multiple fixtures share a workbench. Their compact profile supports flexible fixturing without adding undue bulk to the vise setup, enabling quicker changeovers and simpler handling during assembly or measurement tasks. The mass of 2.97 kg helps maintain positional stability under typical clamping loads, contributing to consistent results across batches. Seamless fit for VQC clamping systems Designed specifically for compatibility with Vertex VQC vises, the VQC-100FJ integrates without modification, allowing straightforward replacement of standard jaws. This direct fit reduces downtime during tool changes and simplifies inventory management for workshops using the VQC range. Clear alignment features and matching mounting points ensure reliable seating and repeatable clamping behaviour in every cycle. Robust service life that supports productivity A focus on practical durability underpins the design of these soft jaws: stable contact during holding phases and reduced need for retightening lead to smoother production flow. By preventing damage to finished surfaces, the jaws indirectly preserve downstream processes such as coating, inspection and assembly. The result is a workholding accessory that supports efficiency while protecting product quality. Contact Metav Werkzeuge to arrange supply of Vertex VQC soft jaws (VQC-100FJ) and receive tailored advice on integration and delivery from Emmerich — our consultants will confirm fitment and dispatch options Technical Data Article number: VQC-100FJ GTIN: 4061905084256 Brand: Vertex Data Dimensions: 99.5×73×50 mm Weight: 2.97 kg eClass: 21029107 Special features Designation: Soft jaws Application: for VQC vises Assets: Technical drawing and detailed images available FAQ What workpiece protection do the soft jaws provide? The VQC-100FJ soft jaws protect sensitive surfaces by distributing clamping force and reducing point loads, which lowers the chance of marks and the need for corrective finishing. Are these jaws compatible with all VQC vise sizes? Compatibility is intended for VQC vises; the VQC-100FJ fits standard Vertex VQC mounting interfaces. Check the vise model to ensure full alignment. Can the jaws be used for precision measurement setups? Yes, the soft clamping surface supports measurement tasks by reducing distortion and offering repeatable seating for delicate components. How does the weight affect clamping stability? At 2.97 kg, the jaw mass contributes to steady contact and helps resist shifts during tightening, improving repeatability in machining cycles. Is a modification required to fit these jaws to an existing vise? No modification is generally required for Vertex VQC systems; the VQC-100FJ is designed for straightforward installation on the corresponding vise models. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Reliable, energy-efficient lighting with a compact form and low weight for easy installation; combines 9 W performance with long service life for uninterrupted workshop use. Order the LED9W directly via Metav Werkzeuge or ask our consultants if needed. LED9W — 9 W LED bulb accessory by Vertex, energy-saving lighting for workshop and industrial applications The LED9W is a compact 9 W LED bulb intended as an accessory for LED lamps, offering efficient illumination where reliable, low-maintenance light is required Long service life reduces replacement frequency Low energy consumption with 9 W rating Compact, lightweight design at 0.19 kg Efficient performance that lowers operational load The 9 W rating of this lamp denotes a energy-efficient alternative to older lighting technologies, delivering comparable illumination while consuming significantly less power. For industrial and workshop settings, this efficiency translates into reduced running hours on electrical supply and a smaller environmental footprint. The built-in advantages of modern LED technology ensure steady light output without frequent fluctuations, which supports process reliability and a more consistent work environment. Designed for dependable, low-maintenance operation This bulb emphasises long service life and low maintenance, reducing downtime for replacements and freeing maintenance resources for other tasks. The solid-state construction typical of LED solutions minimises fragile components and offers stable performance over extended periods. For operations where continuity matters, selecting durable lighting components contributes to predictable scheduling and fewer interruptions to production or workshop routines. Practical handling and quicker installation in busy workshops Weighing only 0.19 kg, the lamp is compact and easy to handle during fitting and replacement, which speeds up installation cycles and reduces effort for technicians. The reduced mass makes it suitable for fixtures with limited load capacity or where repeated handling is required. Its form factor also supports flexible placement in localised task lighting or general area illumination, improving working conditions without complex adjustments. Compatibility and traceable supply for professional procurement Supplied as an accessory for LED lamps, the product is identified by SKU and GTIN for straightforward inventory management and procurement tracking. The clear product identification facilitates reorder processes and ensures that specifications match the intended application. Sourcing through a reliable distributor avoids supply gaps and supports the workshop’s demand for consistent, certified components. Request technical advice from Metav Werkzeuge for the Vertex LED9W 9 W bulb and arrange supply from our Emmerich site — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: LED9W GTIN: 4061905090318 Type: 9 W bulb Facts Power: 9 W Weight: 0.19 kg eClass: 27110390 Special features Accessory for LED lamps Category: Vertex Asset available: LED9W-main.png FAQ What fixtures is this lamp compatible with? The LED9W is suitable as an accessory for LED lamps and can be fitted into compatible LED fixtures that accept a 9 W bulb specification How does the energy consumption compare to older bulb types? The 9 W rating of the LED9W indicates significantly lower energy use compared with traditional incandescent solutions, providing energy savings and reduced electrical load What maintenance can be expected with this bulb? The LED9W offers extended service life and low maintenance requirements, reducing the frequency of replacements and associated downtime Is the weight important for installation? Yes — at 0.19 kg the LED9W is lightweight, which simplifies handling and installation, particularly in fixtures with limited support or where repeated servicing occurs How can this item be reordered for a workshop supply chain? Reorders can be managed using the article number LED9W and GTIN 4061905090318 to ensure the correct SKU is supplied Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan

Technische Daten: Bezeichnung: Abdeckung VHM Material: handeloxiertes Aluminium auch als Satz verfügbar Geeignet für: Schachtbreite 10mm oder Schachtbreite 36mm je nach Ausführung Gewicht: 0,1 kg bis 1,2 kg Länge: 300 mm bis 1000 mm Stück pro Satz: 5 bis 6 Höhe: 13,3mm bis 9,9mm Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Das ist der Hersteller in einigen Worten: Seit der Gründung im Jahr 1978 hat sich VERTEX als eine der führenden Marken in der Branche etabliert. Mit einer beeindruckenden Produktionsfläche von über 15000 m² verfügt VERTEX über die Kapazität, große Mengen hochwertiger Maschinenteile herzustellen, um den steigenden Anforderungen der Kunden gerecht zu werden. Durch modernste Produktionsanlagen und fortschrittliche Fertigungstechnologien gewährleistet VERTEX die Herstellung präziser und langlebiger Produkte. Die Forschung und Entwicklung nimmt bei VERTEX einen hohen Stellenwert ein. Durch kontinuierliche Investitionen in innovative Technologien und Designverbesserungen bleibt VERTEX an der Spitze der Branche. Das engagierte Team von Experten bei VERTEX entwickelt ständig neue und verbesserte Designs, um die Leistung und Effizienz von Maschinen zu steigern. Ein weiterer herausragender Aspekt bei VERTEX ist die hohe Lagerverfügbarkeit. Mit einem beeindruckenden Bestand an Artikeln sind 98% aller Produkte sofort verfügbar. Dies ermöglicht es den Kunden, ihre Produktionsausfallzeiten zu minimieren und den reibungslosen Betrieb ihrer Maschinen sicherzustellen. Als stolzer Hersteller aus Taiwan steht VERTEX für höchste Qualität, Zuverlässigkeit und Kundenzufriedenheit. Die Kunden vertrauen darauf, dass VERTEX ihre Anforderungen versteht und ihnen Maschinenteile von höchster Qualität liefert, die den anspruchsvollen Standards gerecht werden. Interessenten sind herzlich eingeladen, VERTEX zu kontaktieren und mehr über die innovativen Produkte und den erstklassigen Service des Unternehmens zu erfahren. Das Team von VERTEX freut sich darauf, die individuellen Anforderungen der Kunden zu erfüllen und sie bei der Erreichung ihrer geschäftlichen Ziele zu unterstützen.

Technische Daten: Bezeichnung: Zubehör Vollhartmetall Geeignet für: VEC-300G oder VEC-600G je nach Ausführung Gewicht: 0,06 kg - 0,6 kg Typ: Schleifrad, Schnittrad Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Vertex, der Hersteller in einigen Worten: VERTEX ist seit 1978 der führende Hersteller für Maschinenteile in Taiwan. Mit einer beeindruckenden Produktionsfläche von über 15000 m² hat VERTEX die Kapazität, große Mengen hochwertiger Maschinenteile herzustellen, um den steigenden Anforderungen der Kunden gerecht zu werden. Durch einen starken Fokus auf Forschung und Entwicklung ist VERTEX bekannt für seine innovativen Designs, die die Leistung und Effizienz von Maschinen steigern. Die hohe Lagerverfügbarkeit von 98% aller Artikel ermöglicht es den Kunden, schnell und unkompliziert auf ihre Bedürfnisse zu reagieren. VERTEX legt großen Wert auf Qualität und Kundenzufriedenheit und ist bestrebt, die individuellen Anforderungen der Kunden zu erfüllen. Als vertrauenswürdiger Hersteller ist VERTEX stets bereit, seinen Kunden hochwertige Maschinenteile anzubieten und einen herausragenden Service zu gewährleisten.

Technische Daten: Bezeichnung: Anfas- und Entgratmaschine VHM Abmessung: 330x330x300mm bis 500x440mm Besonderheit: Handausführung, gleiche Oberfläche zum Entgraten und Bohren, mit Flansch für Schleifscheibe, geeignet für Stahl, hitzebehandelt, mit Schleifscheibe, geeignet für weiche und harte Materialien, mit austauschbaren Karbid Einsätze, mit quadratischen Wolframkarbid Einsätze 12,7 x 12,7 x 3, 18 mm ISO 1203 SPUN Geeignet für: eiserne Materialien, insbesondere Stahl und Gusseisen oder große Werkstücke die nicht einfach zu Bewegen sind je nach Ausführung Gewicht: 3,7 kg - 40 kg Zubehör inklusive: Fräswendeplatte SEKN 1203 - Wendeplatten SPMW 090304 und ZSPMW 090308 Geschwindigkeit: 0-12000r.p.m. bis 3500r.p.m. Versorgungsspannung: 1Ø, 220V; 50Hz/60Hz - 3Ø 220V oder 1Ø 110V/220V 50Hz/60Hz und 3Ø 380V/415V Drehmoment Winkel: 45° Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Vertex, der Hersteller in einigen Worten: VERTEX ist seit 1978 der führende Hersteller für Maschinenteile in Taiwan. Mit einer beeindruckenden Produktionsfläche von über 15000 m² hat VERTEX die Kapazität, große Mengen hochwertiger Maschinenteile herzustellen, um den steigenden Anforderungen der Kunden gerecht zu werden. Durch einen starken Fokus auf Forschung und Entwicklung ist VERTEX bekannt für seine innovativen Designs, die die Leistung und Effizienz von Maschinen steigern. Die hohe Lagerverfügbarkeit von 98% aller Artikel ermöglicht es den Kunden, schnell und unkompliziert auf ihre Bedürfnisse zu reagieren. VERTEX legt großen Wert auf Qualität und Kundenzufriedenheit und ist bestrebt, die individuellen Anforderungen der Kunden zu erfüllen. Als vertrauenswürdiger Hersteller ist VERTEX stets bereit, seinen Kunden hochwertige Maschinenteile anzubieten und einen herausragenden Service zu gewährleisten.

Technische Daten: Bezeichnung: Arbeitslampe Vollhartmetall IP-Schutz: IP 20 Gewicht: 2,9 kg bis 3,5 kg Fuß: Länge 292mm Zubehör inklusive: Kabel 1,8m Arm: 250x270mm - 480x400mm Leistung: 110V oder 220V je nach Bedarf Dioptrie: 5 Vergrößerung: 2,25x Licht: Halogen bis LED Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Ein paar Worte über den Hersteller: VERTEX, der größte Hersteller für Maschinenteile in Taiwan, hat seit seiner Gründung im Jahr 1978 eine führende Position in der Branche eingenommen. Mit einer beeindruckenden Produktionsfläche von über 15000 m² verfügt VERTEX über die Kapazität, große Mengen hochwertiger Maschinenteile herzustellen und den steigenden Anforderungen der Kunden gerecht zu werden. Durch kontinuierliche Investitionen in Forschung und Entwicklung bleibt VERTEX innovativ und bietet innovative Designs an. Darüber hinaus zeichnet sich VERTEX durch eine beeindruckende Lagerverfügbarkeit aus, da 98% aller Artikel sofort verfügbar sind. Als vertrauenswürdiger Hersteller mit einem Fokus auf Qualität und Kundenzufriedenheit ist VERTEX bereit, die individuellen Anforderungen der Kunden zu erfüllen und ihnen hochwertige Maschinenteile zu liefern.

Technische Daten: Bezeichnung: Aufbewahrungsboxen VHM auch als Satz verfügbar Abmessung: 120x180x80mm - 300x450x177mm Gewicht: 0,585 kg - 9,6 kg Stück pro Satz: 8 - 60 Die technischen Daten beziehen sich auf alle Varianten und können je nach Ausführung variieren. Das ist der Hersteller in einigen Worten: VERTEX ist seit 1978 der führende Hersteller für Maschinenteile in Taiwan. Mit einer beeindruckenden Produktionsfläche von über 15000 m² hat VERTEX die Kapazität, große Mengen hochwertiger Maschinenteile herzustellen, um den steigenden Anforderungen der Kunden gerecht zu werden. Durch einen starken Fokus auf Forschung und Entwicklung ist VERTEX bekannt für seine innovativen Designs, die die Leistung und Effizienz von Maschinen steigern. Die hohe Lagerverfügbarkeit von 98% aller Artikel ermöglicht es den Kunden, schnell und unkompliziert auf ihre Bedürfnisse zu reagieren. VERTEX legt großen Wert auf Qualität und Kundenzufriedenheit und ist bestrebt, die individuellen Anforderungen der Kunden zu erfüllen. Als vertrauenswürdiger Hersteller ist VERTEX stets bereit, seinen Kunden hochwertige Maschinenteile anzubieten und einen herausragenden Service zu gewährleisten.