Take advantage of a ground HSSG cutting geometry combined with a self‑centring 1/4" hex shank to speed up changeovers and deliver consistent M5 threads; order via Metav Werkzeuge for straightforward supply and expert advice. EXACT single-cut thread tap M5 x 15 mm (HSSG) with 1/4" 6‑pt hex shank EXACT single-cut thread tap M5 x 15 mm (HSSG) — a compact, self‑centring tapping tool designed for rapid insertion into 1/4" bit holders and suited to workshop and light production tapping tasks. HSSG ground high-speed steel for durability 1/4" (6.3 mm) hex shank to DIN 3126 Self‑centring design for accurate tapping Thread length 15 mm, total length 36 mm Faster, cleaner thread starts for efficient production The ground HSSG cutting material delivers a sharp, wear‑resistant cutting edge that supports consistent thread quality over multiple cycles. The single‑cut geometry, combined with a short 4–5‑stage chamfer, reduces insertion torque and helps control chip formation during the initial thread engagement. This results in fewer cross‑threads and less rework, which increases throughput in batch tasks and reduces cycle cost per part. The construction is optimised for repeatable performance in standard tapping sequences, where process stability and component conformity are priorities. Reduced downtime with rapid tool changes and secure holding Equipped with a 1/4" (6.3 mm) 6‑point hex shank to DIN 3126, the tool slips straight into common quick‑change bit holders and power tool chucks, enabling fast swaps between operations. The hex interface ensures positive drive and minimises slippage under torque, while the compact overall length of 36 mm supports access in confined setups. The combination of a standardised shank and the self‑centring profile shortens set‑up times and helps maintain concentricity across a production run, which is particularly beneficial when frequent tool changes are part of the workflow. Precise M5 tapping with long‑lasting edge life With a M5 x 15 mm thread length, the tap provides sufficient engagement for secure threads in typical metalworking applications while remaining compact for close‑quarter work. The single‑cut form makes chip evacuation predictable and aids finishing, producing consistent thread form without aggressive material removal. For workshops seeking dependable threaded connections and a tool that balances accessibility with longevity, this tapping tool offers an efficient compromise between precision and service life, reducing the likelihood of premature tool replacement and supporting steady output quality. Contact Metav Werkzeuge for availability of the EXACT M5 x 15 mm single‑cut thread tap and professional advice on integrating it into current production setups; Metav Werkzeuge is ready to assist with technical details and prompt supply. Technical Data Article number: 4000867575NW Label: Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M5x15mm EXACT Manufacturer: EXACT GmbH & Co. KG Präzisionswerkzeuge Packaging unit: 1 UID: 4000867575NW Facts Thread size: M5 Thread length: 15 mm Overall length: 36 mm Shank: 6.3 mm (1/4") hex to DIN 3126 Special features Single‑cut thread tap 4–5‑stage chamfer for controlled thread entry Self‑centring design Cutting material: HSSG 6‑point hex shank according to DIN 3126 FAQ What materials is this tap intended for? The EXACT single‑cut thread tap M5 x 15 mm (HSSG) is made from HSSG, a ground high‑speed steel suited to common workshop materials and general steel tapping tasks, giving balanced wear resistance and edge stability. Can the tap be used in quick‑change holders and impact drivers? Yes, the 1/4" (6.3 mm) 6‑pt hex shank to DIN 3126 is compatible with standard quick‑change bit holders and many power tool chucks; the hex interface ensures positive torque transmission for secure tapping. How does the 4–5‑stage chamfer affect performance? The short 4–5‑stage chamfer provides a progressive thread entry that eases initial engagement, improves chip control and reduces the risk of misalignment at the start of tapping. Is the thread length sufficient for repair and assembly work? A 15 mm thread length offers reliable engagement for many assembly and repair tasks where secure M5 threads are required while keeping the tool compact for restricted spaces. What is the SKU for ordering and reference? Reference SKU 4000867575NW when enquiring about the EXACT single‑cut thread tap M5 x 15 mm (HSSG) to ensure correct identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M8x19mm EXACT — Präziser Gewindeschneider für Serienfertigung Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M8x19mm EXACT eignet sich für effiziente Innengewinde in Serien- und Werkstattfertigung, bietet hohe Standzeit durch HSSG-Schneidstoff und kompatible Aufnahme über 6,3 mm Sechskantschaft nach DIN 3126 HSSG-Schneidstoff für erhöhte Standzeit 4-5-Gang-Anschnitt für sauberen Spanabtrag 6,3 mm Sechskantschaft nach DIN 3126 Gewindelänge 19 mm für sichere Verbindung Gesamtlänge 40 mm, kompakte Bauform Hält Produktionszyklen stabil und reduziert Nacharbeit Der HSSG-Schneidstoff gewährleistet eine hohe Verschleißfestigkeit und verlängerte Standzeit, was die Werkzeugwechselintervalle reduziert. Durch den 4-5-Gang-Anschnitt wird die Spanbildung kontrolliert, sodass die Oberflächenqualität des Gewindes steigt und Nacharbeiten seltener werden. Für Anwender bedeutet das kalkulierbare Laufzeiten und geringere Stillstandszeiten in der Fertigung. Kompatible Aufnahme und einfache Integration in Bohr- und Gewindeschneidprozesse Dank des 6,3 mm Sechskantschafts nach DIN 3126 passt der Gewindebohrer in gängige Schnellwechselfutter und 1/4″-Bitsysteme, was die Werkzeughandhabung vereinfacht. Die selbstzentrierende Ausführung unterstützt ein exaktes Ansetzen, wodurch das Risiko von Ausrissen bei dünnwandigen Werkstücken reduziert wird. Diese Merkmale erleichtern die Integration in bestehende Bearbeitungsprozesse ohne Zusatzaufwand. Technische Vorteile für präzise Schraubverbindungen Mit einer Gewindelänge von 19 mm und einer Gesamtlänge von 40 mm liefert der Einschnittgewindebohrer reproduzierbare Gewindequalitäten, die in Montagesituationen für sichere Schraubverbindungen sorgen. Die kompakte Bauform ermöglicht den Einsatz in beengten Einbauräumen, während die präzise Geometrie für gute Gewindeschlüssigkeit und Wiederholgenauigkeit sorgt. Für welche Anwendungen und Werkstoffe geeignet Dieses Werkzeug eignet sich besonders für die Bearbeitung von unlegierten Stählen und Werkstücken, bei denen ein robuster Schneidstoff gefordert ist. Die Konstruktion ist ausgelegt auf Serienanwendungen in Handwerk und Industrie, wo Effizienz und Prozesssicherheit im Vordergrund stehen. Anwender profitieren von geringem Rüstaufwand und hoher Reproduzierbarkeit bei wiederkehrenden Fertigungsaufträgen. Für konstante Produktionsqualität den HSSG-Einschnittgewindebohrer von EXACT über Metav Werkzeuge beziehen – Beratung und Bestellung per eMail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 4000867578NW Bezeichnung: Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M8x19mm EXACT Hersteller: EXACT GmbH & Co. KG Präzisionswerkzeuge Verpackungseinheit: 1 Daten Gewindelänge: 19 mm Gesamtlänge: 40 mm Sechskantschaft: 6,3 mm (1/4") Besonderheiten Schneidstoff: HSSG 4-5-Gang-Anschnitt Selbstzentrierend Sechskantschaft nach DIN 3126 FAQ Wie lange ist die Gewindelänge und warum ist das wichtig? Die Gewindelänge beträgt 19 mm. Eine definierte Gewindelänge sorgt beim Einschnittgewindebohrer von EXACT für ausreichende Gewindetragfähigkeit und zuverlässige Kraftübertragung in Montageanwendungen. Welche Aufnahme passt für dieses Werkzeug? Der Einschnittgewindebohrer nutzt einen 6,3 mm Sechskantschaft nach DIN 3126, wodurch eine schnelle Montage in üblichen Bithaltern und Schnellwechselfuttern möglich ist. Aus welchem Schneidstoff besteht das Werkzeug und welchen Nutzen bietet das? Der Schneidstoff ist HSSG. Diese Materialwahl erhöht die Verschleißfestigkeit und Standzeit, was besonders bei Serienfertigung wirtschaftliche Vorteile bringt. Ist das Werkzeug selbstzentrierend und wo hilft das? Ja, der Gewindebohrer ist selbstzentrierend ausgeführt. Das erleichtert das saubere Ansetzen, reduziert Auftreiber und verbessert die Gewindequalität, insbesondere bei dünnwandigen Bauteilen. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining HSSG cutting steel with a compact 33 mm overall length provides fast, repeatable M3 thread production and reliable engagement in confined setups; order the EXACT single‑cut tap directly via Metav Werkzeuge or ask the consultants for compatibility details. EXACT M3x11 mm single‑cut tap HSSG with 1/4″ hex shank The EXACT M3x11 mm single‑cut tap HSSG with 1/4″ hex shank is a compact tapping tool designed for producing M3 internal threads where space is limited and secure drive engagement is required HSSG solid ground high-speed steel Self‑centring 1/4″ hex shank Thread length 11 mm for M3 threads Overall length 33 mm for compact use Precision cutting in a compact form for consistent threads The ground HSSG substrate provides a hard, wear‑resistant cutting edge that maintains dimensional stability over repeated cycles. With a thread length of 11 mm, the tool forms a full M3 thread depth while limiting axial engagement to controllable lengths, which reduces torque spikes in small assemblies. The short overall length of 33 mm allows access in confined fixturing and minimises overhang, resulting in reduced run‑out and improved concentricity compared with longer taps. This combination supports efficient series production and predictable thread quality. Secure drive and fast set‑up for workshop and machine use A 6.3 mm (1/4″) hex shank ensures positive drive engagement with quick‑change chucks and standard bit holders; the self‑centring geometry promotes reliable alignment during hand‑held or machine operations. The compact drive interface shortens set‑up times and reduces the need for additional adaptors, improving throughput in assembly lines and maintenance tasks. The hex shank also enables the use of powered screwdrivers for controlled tapping in repetitive operations, supporting consistent cycle times and reduced operator fatigue. Practical lead geometry and straightforward handling The tool features a 4–5 chamfer lead that eases thread entry and reduces the likelihood of cross‑threading in pre‑drilled holes. The single‑cut design provides a clear chip formation path, simplifying chip evacuation and minimising clogging in shallow threaded holes. This makes the tap particularly suitable where reliable thread starts and clean chip removal are priorities. The hardened, ground cutting edges support repeatable performance and make the tool a sensible choice for technicians seeking a balance between durability and compact handling. Contact Metav Werkzeuge today to check stock and suitability for the HSSG M3 single‑cut tap (SKU 4000867573NW) and receive tailored advice from the Metav precision team Technical data SKU: 4000867573NW Label: Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M3x11mm EXACT Manufacturer: EXACT GmbH & Co. KG Präzisionswerkzeuge Facts Thread length: 11 mm Overall length: 33 mm Hex shank diameter: 6.3 mm (1/4″) Cutting material: HSSG Special features Single‑cut tap design 4–5 chamfer lead 6KT (6‑point) hex bit drive Self‑centring drive interface FAQ What thread size does the tap produce? The tap produces M3 internal threads with a thread length of 11 mm and a compact overall length of 33 mm. Is the driving interface compatible with power bit holders? Yes, the 6.3 mm (1/4″) hex shank is compatible with standard quick‑change bit holders and powered screwdriver chucks. What material is the cutting part made from? The cutting material is HSSG, a ground high‑speed steel grade designed for wear resistance and repeatable cutting performance. How does the chamfer design affect thread starting? The 4–5 chamfer lead eases thread entry, reduces cross‑threading risk and supports controlled chip formation during the initial engagement. What is the SKU for ordering and enquiries? The SKU is 4000867573NW, referenced for stock checks and compatibility enquiries with Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise HSSG cutting geometry, a self‑centring start and a standard 1/4″ hex drive for fast changeover, which together ensure consistent thread quality and reduced setup time on production runs. Order the EXACT single‑cut tap directly via Metav Werkzeuge or ask the consultants for application support. EXACT Single‑cut Tap HSSG M4 x 12 mm with 1/4″ Hex Shank — 4–5‑thread taper, self‑centring The EXACT single‑cut HSSG tap M4 x 12 mm is a compact, production‑oriented cutting tool designed for reliable internal thread formation in workshops and machining cells. Ground HSSG cutting material 4–5‑thread taper for smooth entry 6.3 mm (1/4″) hex shank to DIN 3126 Self‑centring for consistent starts Consistent threading from ground HSSG for industrial use The core design focuses on efficient, repeatable results: the HSSG cutting material combines toughness and edge retention for a broad range of workpiece steels and common workshop alloys. The 4–5‑thread taper (short chamfer) ensures controlled entry into pre‑drilled holes, reducing the risk of cross‑threading and minimising required alignment work. For production environments where cycle time and first‑pass quality matter, this tap reduces rework and supports steady throughput by providing a clean, accurate M4 x 12 mm thread with every pass. Fast tool change and reliable centring to speed up processes The hex drive is sized at 6.3 mm (1/4″) and conforms to DIN 3126, enabling secure clamping in standard quick‑change tool holders and screwdrivers. The compact overall length of 35 mm and the short chamfer make the tool suitable for confined setups and multi‑spindle applications. Thanks to the self‑centring geometry, starts are more reliable on interrupted surfaces and blind holes, cutting down on alignment time and improving operator confidence in repetitive tasks. Practical compatibility and workshop benefits explained Interpreting the technical details for everyday use: the ground high‑speed steel body delivers a sharp cutting edge that tolerates standard workshop feeds and coolant regimes; the short chamfer (4–5‑thread) is a compromise between aggressive cutting and controlled engagement, ideal for through holes and shallow blind holes up to the specified thread depth. The hex shank format means the tool is immediately compatible with common manual and powered drivers, reducing the need for specialised adaptors and keeping changeover straightforward in mixed‑tool environments. Contact Metav Werkzeuge for tailor‑made advice on implementation or to confirm material compatibility and clamping recommendations for this EXACT single‑cut tap. Technical data Article number: 4000867574NW Label: Einschnittgewindebohrer HSSG 1/4 Zoll 6KT-Bit M4x12mm EXACT Manufacturer: EXACT GmbH & Co. KG Präzisionswerkzeuge Packaging unit: 1 UID: 4000867574NW Dimensions & core values Thread length: 12 mm Overall length: 35 mm Shank diameter: 6.3 mm (1/4″) Thread: M4 x 12 mm Special features Material: HSSG (ground high‑speed steel) Short 4–5‑thread taper chamfer 6.3 mm (1/4″) hex shank to DIN 3126 Self‑centring start Compact, production‑oriented geometry FAQ What materials is this tap suitable for? The tap uses HSSG cutting material and is suitable for common workshop steels and general engineering alloys; performance will depend on the specific workpiece material and cutting parameters. How does the 4–5‑thread taper affect entry and thread quality? The short taper provides controlled engagement, allowing the tap to enter more smoothly while maintaining dimensional accuracy for the M4 x 12 mm thread. Is the 1/4″ hex shank compatible with quick‑change holders? Yes, the 6.3 mm (1/4″) hex shank conforms to DIN 3126 and is compatible with standard quick‑change tool holders and hex collets. Can this tool be used for blind holes? The compact overall length and short chamfer make the tap suitable for shallow blind holes up to the specified thread depth, with careful control of thread‑bottom clearance. What is the overall length and how does it affect accessibility? The overall length is 35 mm, making the tool well suited to tight working spaces and applications with limited tool reach. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combine the HSSG ground cutting material with a self‑centring 6.3 mm (1/4″) hex shank and a 21 mm thread length to achieve consistent M10 thread production; order the tool directly via Metav Werkzeuge or consult their specialists for specific application advice. Single‑flute thread tap HSSG M10 x 21 mm — 6.3 mm (1/4″) hex shank by EXACT A single‑flute, HSS ground thread tap designed for precision M10 thread cutting with a self‑centring 6.3 mm (1/4″) hex shank suitable for workshop and light industrial tooling HSSG ground cutting material Self‑centring 6.3 mm (1/4″) hex shank 21 mm thread length for M10 threads 4–5 stage chamfer for reliable entry High precision where every thread counts The combination of HSSG cutting steel and a single‑flute geometry delivers a predictable cutting action for metric M10 threads. The ground cutting faces reduce burr formation and ensure repeatable thread profiles, which supports consistent assembly tolerances. With a 21 mm thread length and an overall length 41 mm, the tool is dimensioned to provide secure engagement with the workpiece while limiting unnecessary exposure of the shank. Technical users will value the measured design, which helps to reduce rework and maintain production rhythm. Faster set‑ups and secure tool retention Equipped with a 6.3 mm (1/4″) hex shank to DIN 3126, the tap is compatible with standard quick‑change holders and hex collets, enabling rapid tool changes and straightforward integration into existing tooling systems. The self‑centring feature reduces initial misalignment and the need for complex fixturing during manual or semi‑automatic tapping. This contributes to a leaner workflow, fewer set‑up steps and improved throughput in repetitive operations. Entry control and durable service life A 4–5 stage chamfer at the entry promotes reliable thread engagement and smoother chip formation during penetration, which is particularly helpful when starting threads in pre‑drilled holes. The use of HSSG as the cutting material supports stable cutting edges and long service intervals under standard workshop conditions. The overall construction, including the adherence to DIN 3126 for the hex shank, facilitates safe tool handling and predictable replacement cycles, reducing downtime for maintenance. For reliable M10 tapping with proven HSSG performance, contact Metav Werkzeuge for purchase and tailored technical advice on the EXACT single‑flute tap (SKU 4000867580NW), available from stock in Emmerich. Technical Data Article number: 4000867580NW Product name: Einschnittgewindebohrer HSSG M10x21mm EXACT Manufacturer: EXACT GmbH & Co. KG Präzisionswerkzeuge Packaging unit: 1 UID: 4000867580NW Numbers / Core technical data Thread size: M10 Thread length: 21 mm Overall length: 41 mm Shank diameter: 6.3 mm (1/4″) Chamfer: 4–5 stage Special features / Design Cutting material: HSSG Single‑flute (single‑cut) geometry Self‑centring design Hex shank to DIN 3126 FAQ What thread size does this tap produce? The tap produces standard M10 threads; the tool is specified as M10 x 21 mm for the thread length. Is the shank compatible with quick‑change hex holders? Yes, the tool has a 6.3 mm (1/4″) hex shank to DIN 3126 and is intended for secure retention in standard hex holders. What is the purpose of the 4–5 stage chamfer? The 4–5 stage chamfer facilitates controlled entry into the material, improving initial engagement and chip evacuation during thread formation. Which cutting material is used for the tap? The tap is manufactured from HSSG, a ground high‑speed steel chosen for stable cutting edges and durable life in typical workshop applications. What is the article number for reordering or reference? The article number (SKU) is 4000867580NW and can be referenced when enquiring or ordering. Manufacturer: EXACT GmbH & Co. KG Präzisionswerkzeuge; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of HSS‑Co cutting material, straight flute Form B geometry and an ISO2 tolerance for consistent thread quality across production batches; order the tap directly via Metav Werkzeuge or request advice from the consultants if necessary. Single-flute tap DIN 352 Form B M10 x 1.5 HSS‑Co (ISO2/6H) – TECWERK A single-flute tap DIN 352 Form B M10 x 1.5 HSS‑Co (ISO2/6H) designed for cutting precise metric through threads in medium-to-high strength steels Cobalt high-speed steel (HSS‑Co) cutting material Straight flute, Form B geometry for stable cutting Metric M10 x 1.5 thread, tolerance ISO2 (6H) Optimised for through holes with shearing chamfer Consistent fit and repeatable assembly quality The tool is manufactured to DIN 352 and cuts metric M10 x 1.5 threads with the ISO2 (6H) tolerance band, ensuring predictable thread geometry for serial production and repair work. The flank relief ground on the thread flanks reduces friction during tapping and helps achieve a reliable mating fit; this translates into fewer rework cycles and less scrap when repeatability matters. The adherence to recognised standards supports interchangeability and simplifies quality documentation for procurement and inspection processes. Durable performance in demanding steels Machined from HSS‑Co (cobalt high-speed steel), the tap offers improved red hardness and wear resistance compared with conventional high-speed grades, which is reflected in extended tool life during continuous use. It is rated for machining steel up to 900 N/mm² tensile strength, making it suitable for many alloyed and carbon steels encountered in maintenance and production. The tool is uncoated, providing a neutral surface ideal where coatings could affect thread tolerances or where regrinding is anticipated. Reliable chip control and clean through-threading The straight flute geometry combined with a specialised shearing chamfer for through holes promotes consistent chip formation and evacuation when tapping clear holes. This reduces the risk of chip jamming and improves surface finish in the thread root, which is particularly beneficial in blind-entry operations followed by through-hole tapping or in stacked production where process stability is essential. The design supports straightforward tapping cycles on both manual equipment and machine tapping heads. Practical integration into workshop workflows Supplied as a single unit, the tap suits toolrooms and production lines that require standard-compliant, easy-to-select tooling. The Form B configuration provides a balanced compromise between cutting action and edge stability, aiding use across common applications without frequent tool changes. For specification clarifications or to check compatibility with existing holders and tapping cycles, Metav’s technical literature and product documentation can be consulted; their role as a precision partner helps reduce procurement complexity and ensures consistent supply for workshop needs. For fast supply and expert advice on integrating this TECWERK single-flute tap into production, contact Metav Werkzeuge for order and specification support via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000867327NW Manufacturer: TECWERK Packaging unit: 1 Specifications Thread: M10 x 1.5 mm Tolerance: ISO2 (6H) Standard: DIN 352 Form B Suitable for steels up to approx. 900 N/mm² tensile strength Features Cutting material: HSS‑Co (cobalt high-speed steel) Flute type: straight flute (Form B) Flanks: flank relief ground Coating: uncoated Chamfer: shearing chamfer for through holes Thread standard: metric ISO thread (DIN 13 Blatt 1) FAQ What materials can this tap machine effectively cut? The TECWERK single-flute tap is specified for machining steels up to approximately 900 N/mm² tensile strength and is suitable for common alloyed and carbon steels. Is the tap coated, and what implications does that have? The tap is uncoated; this preserves dimensional stability for regrinding and avoids coating-related tolerance shifts while retaining the wear resistance benefits of HSS‑Co. Which standard and tolerance does the tap comply with? The tool conforms to DIN 352 Form B and produces metric threads to ISO2 (6H) tolerance, enabling consistent fits for standard fasteners. Can this tap be used for through-hole tapping on automated machines? Yes, the straight flute and shearing chamfer are optimised for through holes, assisting chip evacuation in machine tapping cycles as well as manual operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the robust cutting geometry and cobalt-enhanced HSS to achieve consistent M12 x 1.75 threading with minimal rework; order through Metav Werkzeuge or consult its workshop specialists for application advice. Single-cut tap DIN 352 Form B M12 x 1.75 HSS‑Co ISO2 (6H) — TECWERK A single‑cut metric tap designed for producing accurate through‑threads in medium‑strength steels in workshop and production environments. Cobalt high-speed steel (HSS-Co) for wear resistance Straight flute Form B for stable chip control Relief-ground flanks for smooth thread entry Chamfered lead for reliable through-threading Greater process reliability through hardened cutting geometry This TECWERK single‑cut tap is manufactured from HSS‑Co, combining toughness with wear resistance to extend life in serial tapping operations. The Form B design and straight-flute geometry deliver controlled chip formation, which reduces the risk of chip jamming and subsequent thread damage. For production environments that value repeatable quality, the result is fewer rejected parts and less downtime, as the tool’s geometry supports consistent thread profiles and dimensional stability. Smooth engagement and reduced thread rework The tap’s relief-ground flanks and chamfered lead are engineered to ensure gradual tool engagement and reliable centring when cutting metric ISO threads. These features reduce insertion torque and minimise wobble during hand or machine tapping, which translates into smoother machining cycles and a lower rate of thread correction. When working with medium-strength steels, the combination of cutting material and flank relief helps maintain thread form and surface finish, so post‑machining processes are shortened. Standards and compatibility explained for easier selection Supplied for M12 x 1.75 mm metric threads to DIN 13 (sheet 1) with tolerance class ISO2 (6H), this tool fits standardised tapping workflows and inspection routines. “Single‑cut” indicates a single fluted profile optimised for through‑holes and straightforward chip evacuation; the tool is uncoated, making it suitable for general steel applications and for users who prefer regrinding and maintenance rather than sacrificial coatings. For steels up to approximately 900 N/mm² tensile strength the tool offers an effective balance between hardness and toughness. Practical workshop advice and application scenarios In a busy workshop, this tap excels when used in dedicated tapping holders or machine spindles where alignment is controlled; the straight flute and chamfer work particularly well for blind‑reamed or through‑drilled holes prepared to standard hole sizes for M12 threads. The tool’s HSS‑Co composition supports intermittent cutting and higher thermal loads compared with standard HSS, making it a pragmatic choice for small batch production and maintenance tasks where durability matters. For optimal service life, pair the tap with appropriate coolant and moderate feed rates that match the workpiece material and machine rigidity. Contact Metav Werkzeuge for tailored advice on integrating the TECWERK single‑cut tap into workshop processes or to check stock and delivery options — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: 2000867328NW SKU: 2000867328NW Packaging unit: 1 Label: Single-cut tap DIN 352 Form B M12 x 1.75 HSS-Co ISO2 (6H) TECWERK Core measurements Thread: M12 x 1.75 mm Tolerance class: ISO2 (6H) Standard: DIN 13, sheet 1 Recommended workpiece strength: up to approximately 900 N/mm² Special features Material: HSS‑Co (cobalt high-speed steel) Form: B (single-cut) Flute: straight flute Flank treatment: relief-ground flanks Coating: uncoated Lead: chamfered lead for through threads FAQ What materials is this tap suitable for? The Single-cut tap DIN 352 Form B M12 x 1.75 HSS‑Co ISO2 (6H) TECWERK is intended primarily for steels and is rated for workpieces up to around 900 N/mm² tensile strength. Is the tool suitable for through‑threads or blind holes? The chamfered lead and straight-flute design make the TECWERK single‑cut tap particularly suited to reliable through‑threading; it can be used in blind holes if chip evacuation is ensured. What tolerance and standard does the tap conform to? This tapping tool conforms to DIN 13 (sheet 1) and produces threads to tolerance class ISO2 (6H), appropriate for standard metric assembly requirements. Does the tap have a coating for improved wear resistance? The tool is supplied uncoated; longevity is achieved through the HSS‑Co cutting material and the controlled geometry rather than a surface coating. Can the tap be used in handheld tapping wrenches or only in machines? The geometry supports both machine and controlled hand tapping; however, for consistent results and reduced breakage risk, machine tapping with rigid alignment or tapping holders is recommended. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

High-precision M3 threads are achieved by combining HSS‑Co cutting steel with ISO2 (6H) tolerance and a Form B straight‑fluted geometry, delivering consistent thread quality and extended tool life for steels up to approximately 900 N/mm². Order the TECWERK single‑cut tap directly via Metav Werkzeuge or ask our consultants if needed. TECWERK single-cut tap, M3 x 0.5 mm — HSS‑Co, ISO2 (6H) TECWERK single‑cut tap for producing metric M3 x 0.5 threads in medium‑strength steels and general workshop applications HSS‑Co cutting material Form B, straight‑fluted design M3 × 0.5 metric ISO thread ISO2 (6H) tolerance for precise fits Precise threads with industrial tolerances for reliable assemblies The straight‑fluted single‑cut tap is manufactured to DIN 352 and delivers a reliably controlled thread form thanks to the ISO2 (6H) tolerance band. This tighter tolerance ensures consistent screw fits and reduces assembly rework, an important efficiency factor in production environments. The cobalt‑alloyed HSS‑Co offers improved hot‑hardness compared with standard high‑speed steel, which helps maintain cutting geometry under elevated temperatures and in demanding series work. Designed for through‑hole threading and clean chip evacuation The tool features a Form B straight flute geometry combined with a special cutting lip for through‑hole threads, which promotes controlled chip formation and evacuation during tapping. The flank honing (flanked, honed edges) reduces burr formation and improves surface quality on the flank, meaning fewer downstream finishing steps. This design is particularly suitable where clean, repeatable threads are required in mechanical assemblies. Material compatibility and workshop performance Optimised for steels with tensile strength up to about 900 N/mm², the geometry and cutting material provide a balance between wear resistance and toughness. The tap is uncoated, avoiding potential coating flaking in interrupted cuts, while the cobalt content improves wear resistance over plain HSS. For routine maintenance and repair tasks in workshops or small‑batch production, the tool offers dependable tool life and predictable regrindability when required. Practical benefits and integration into production Specifying a tap with clear standards (DIN 352, ISO2) and a known material like HSS‑Co simplifies procurement and quality control processes. The straight flute and honed flanks reduce post‑threading cleaning and minimise the risk of thread damage during assembly, lowering rejection rates. For procurement managers and workshop supervisors, this results in fewer process interruptions and a more consistent end product. For reliable M3 thread production, choose the TECWERK single‑cut tap and contact Metav Werkzeuge for technical advice or supply arrangements at info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: 2000867322NW Label: Einschnittgewindebohrer DIN 352 Form B M3x0,5mm HSS-Co ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867322NW Specifications Thread size: M3 × 0.5 mm Tolerance: ISO2 (6H) Standard: DIN 352 Cutting material: HSS‑Co Coating: uncoated Suitable for steels up to ≈ 900 N/mm² Features Form B, straight‑fluted geometry Single‑cut tap design Flank honing for improved surface quality With cutting lip for through‑hole threads Metric ISO thread form FAQ What materials is this tap suited for? The TECWERK single‑cut tap is specified for use in steels up to approximately 900 N/mm² tensile strength and is uncoated to avoid coating issues in interrupted cuts. Which standards and tolerances does this tap conform to? This tap is manufactured to DIN 352 and produces threads to ISO2 (6H) tolerance for consistent metric fits. Is the cutting material suitable for extended production runs? Yes, the HSS‑Co construction provides enhanced hot‑hardness and wear resistance compared with plain HSS, making it suitable for many small‑ to medium‑batch operations. How does the Form B geometry benefit through‑hole threading? The straight‑fluted Form B design, combined with a cutting lip for through threads, promotes controlled chip formation and evacuation, reducing the risk of chip clogging and improving thread quality. What is the article number for ordering and reference? Use article number 2000867322NW (TECWERK single‑cut tap, M3 × 0.5 mm) when ordering or requesting technical information. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a durable HSS‑Co construction, precise ISO2 (6H) thread tolerance and a straight‑fluted Form B geometry that together ensure reliable M4 through threads in medium‑strength steels; order this tap directly via Metav Werkzeuge or ask our consultants for tailored advice. Tap DIN 352 Form B M4 x 0.7 mm HSS‑Co ISO2 (6H) — TECWERK The Tap DIN 352 Form B M4 x 0.7 mm HSS‑Co ISO2 (6H) is a single‑cut machine tap designed for producing precise metric through threads in steels up to approximately 900 N/mm², with straight flutes and relieved flank geometry for consistent thread quality HSS‑Co for high wear resistance Straight flutes for reliable chip evacuation ISO2 (6H) tolerance for precise metric threads Precision where standard conformity matters This threading tool is manufactured to DIN 352 and delivers the ISO2 (6H) tolerance commonly required in industrial assemblies. The combination of a cobalt‑alloyed high‑speed steel (HSS‑Co) substrate and the Form B specification results in a tool that maintains cutting geometry under repeated use. For procurement and production planning, the standard compliance means predictable fitting behaviour and reduced sorting at inspection — a clear advantage for workshops and small production lines that demand repeatable accuracy. Engineered performance for common steels Specified for use in steels up to 900 N/mm², the tap’s material choice and geometry balance toughness and wear resistance. HSS‑Co provides enhanced heat resistance compared with conventional high‑speed steels, which helps during interrupted cuts or when higher cutting speeds are required. The tool is uncoated, allowing for stable performance in lubricated operations and straightforward regrinding when service life is reached — a practical benefit for maintenance budgets and tool life management. Reliable chip control and thread integrity The straight flutes and relieved flanks support effective chip evacuation and reduce the risk of thread deformation in through‑hole applications. The incorporated cutting chamfer for through threads minimises initial cutting forces and helps produce clean thread starts, which simplifies assembly and improves torque characteristics of threaded fasteners. For users less familiar with tap geometry: relieved flanks reduce friction along the thread flank, enhancing surface finish and measurement conformity. Selection and application made straightforward As a single‑cut (einschnitt) machine tap in Form B, the tool is suited to standard tapping heads and machine spindles; it is intended primarily for through‑hole threads. When matching to a process, consider the M4 x 0.7 mm designation together with the stated material suitability to ensure compatibility with workpiece strength and cutting parameters. For additional application data or cutting recommendations, technical support is available by e‑mail at info@metav-werkzeuge.com or by telephone at +49 2822 7131930, so production decisions can be made with documented guidance. For secure supplies of TECWERK taps and expert advice on process integration, contact Metav Werkzeuge to discuss lead times and application support from our Emmerich location. Technical data Article number: 2000867323NW Product: Tap DIN 352 Form B M4 x 0.7 mm HSS‑Co ISO2 (6H) Brand: TECWERK Packaging unit: 1 Core specifications Thread: M4 x 0.7 mm Standard: DIN 352 Tolerance: ISO2 (6H) Material: HSS‑Co Suitable for steels up to approx. 900 N/mm² Special features Single‑cut design Straight flutes for chip evacuation Relieved flanks Cutting chamfer for through threads Uncoated FAQ Which materials is this tap suitable for? The TECWERK tap is specified for use in steels up to approximately 900 N/mm² and is optimised for through‑thread machining in such materials. Is this tap suitable for through holes or blind holes? The tool features a cutting chamfer designed specifically for through threads, making it most suitable for through‑hole applications. What standard and tolerance does the tap conform to? Manufactured to DIN 352, the tap provides an ISO2 (6H) tolerance for metric threads, ensuring interchangeability and consistent fit. Does the tool have a coating for wear protection? This TECWERK tap is uncoated, relying on the cobalt‑enriched high‑speed steel substrate for wear resistance and heat tolerance. What size and form is the tap and where to order it? Designation: M4 x 0.7 mm, Form B, single‑cut. Order enquiries can be placed via Metav Werkzeuge; refer to article number 2000867323NW for precise ordering. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co hardness, ISO2 (6H) tolerance and a straight‑flute design for reliable thread quality and consistent chip evacuation; order directly via Metav Werkzeuge or contact our consultants for application advice. Single‑flute thread tap DIN 352 Form B M5×0.8 HSS‑Co ISO2 (6H) TECWERK — straight‑fluted, uncoated metric tap for through holes A Single‑flute thread tap DIN 352 Form B M5×0.8 HSS‑Co ISO2 (6H) designed for producing ISO metric internal threads in medium to high‑strength steels, optimised for clean chip removal and accurate thread geometry. HSS‑Co for increased wear resistance Straight flutes (Form B) for through holes ISO2 (6H) tolerance for precision fit Peeling chamfer for clean thread entry Faster, more reliable threading in tougher steels Made from HSS‑Co, this single‑flute tap delivers elevated red‑hardness and improved wear resistance compared with standard high‑speed steels, which translates into longer tool life when machining tougher workpieces. The straight‑flute Form B geometry supports effective chip evacuation in through‑hole applications; fewer chip jams mean shorter cycle times and less interruptive rework. The peeling chamfer (Schälanschnitt) eases thread engagement and produces a clean start, reducing the need for secondary operations and improving overall process efficiency. Precision threads that meet industrial standards Thread form and fit are critical in assembly. The tap conforms to DIN 13, Sheet 1 and produces metric ISO threads with the ISO2 (6H) tolerance field, ensuring consistent internal thread accuracy and interchangeability with standard fasteners. The combination of flank relief grinding and the chosen tolerance class reduces cutting forces and minimises the risk of seizure in medium‑strength steels up to approximately 900 N/mm² tensile strength. These characteristics support dependable assembly outcomes in production and maintenance environments. Practical handling and process advantages The single‑groove design concentrates cutting action and makes chip control predictable in continuous runs; this simplifies coolant access and cleaning routines. Although uncoated, the cobalt‑alloyed substrate maintains hardness under heat, so shorter dwell periods and stable feeds remain possible without premature flank wear. The tool’s geometry also reduces the tendency to create burrs at the thread start, which lowers finishing work and improves downstream quality control metrics. Where this tap is most effective Ideal for metalworking shops and production lines that require repeatable metric threadmaking in through holes, the tool suits applications in mechanical engineering, maintenance workshops and component assembly. The tap is particularly effective for medium‑to‑high strength steels where elevated thermal stability and wear resistance are required but coating is not essential. It also performs well where controlled chip formation and removal are priorities. For tailored advice or to place an order through Metav Werkzeuge – the experienced partner for precision tools and measurement – contact our specialists for application guidance and delivery options. Technical Data Article number: 2000867324NW Product: Single‑flute thread tap DIN 352 Form B M5×0.8 HSS‑Co ISO2 (6H) TECWERK Manufacturer: TECWERK Packing unit: 1 Facts Thread size: M5 × 0.8 Tolerance: ISO2 (6H) Suitable material tensile strength: up to approx. 900 N/mm² Special features Form: B (straight fluted) Cutting material: HSS‑Co Coating: uncoated Flank relief ground Peeling chamfer for through threads Metric ISO thread to DIN 13 Sheet 1 FAQ What materials is this tap suitable for? The Single‑flute thread tap DIN 352 Form B M5×0.8 HSS‑Co ISO2 (6H) is specified for use in steels up to approximately 900 N/mm² tensile strength and is designed for medium‑ to high‑strength steel applications. Is the tap coated for improved wear resistance? This TECWERK tap is uncoated; wear resistance is provided by the HSS‑Co substrate, which maintains hardness at elevated cutting temperatures. What advantages does the straight‑flute (Form B) geometry provide? Straight flutes facilitate predictable chip evacuation in through‑hole threading and help reduce chip packing, making the tool particularly effective in continuous production where clean chip removal is essential. Does the tap produce threads to an industry standard tolerance? Yes. Threads produced by this tap conform to DIN 13, Sheet 1 and are manufactured to the ISO2 (6H) tolerance field for a standardised fit with metric fasteners. Can this tap be used for blind holes? The design, including the peeling chamfer, is optimised for through holes; when used in blind holes, chip evacuation must be managed carefully to avoid chip accumulation. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of ground high‑speed steel and a self‑centring geometry to speed up thread production while maintaining consistent M6 results; order directly via Metav Werkzeuge or consult our specialists for application advice. Single‑cut thread tap HSS‑G, 1/4″ hex shank — EXACT M6 x 18 mm, self‑centring Single‑cut thread tap HSS‑G, 1/4″ hex shank — EXACT is a compact metric tap designed for reliable M6 thread formation in production and workshop environments Ground HSS‑G cutting material Self‑centring geometry for fast alignment 6.3 mm (1/4") hex shank to DIN 3126 18 mm thread length, 39 mm overall Consistent thread quality from ground HSS‑G The tap combines ground high‑speed steel (HSS‑G) with a single‑cut geometry to deliver predictable chip formation and repeatable thread profiles. Ground HSS‑G offers a uniform cutting edge that reduces burr formation and supports a stable flank finish; this results in fewer reworks and a higher first‑pass yield. The specified M6 x 18 mm thread length provides adequate engagement for common metric fastenings while the compact profile supports tight assembly spaces. Rapid clamping and secure drive for efficient changeovers Equipped with a 6.3 mm (1/4") hex shank to DIN 3126, the tool fits quick‑change screwdriver and driver systems, enabling swift tool changes and reduced downtime in batch operations. The hex interface ensures positive torque transmission and limits slippage under load, which contributes to consistent thread depth and pitch. The self‑centring feature helps to position the tool accurately at the start of the hole, lowering the risk of cross‑threading and improving process reliability. Compact design for versatile workshop use With an overall length of 39 mm and a thread length of 18 mm, the cutter is suited to confined fixtures and stacked assemblies where space is restricted. The 4–5‑cut chamfer provides a progressive entry for the tap, aiding lead‑in and easing initial engagement. As a single‑cut tapping solution, it is particularly useful where a clean surface finish and controlled chip evacuation are priorities, and where operators value predictable handling characteristics during manual or machine tapping operations. Contact Metav Werkzeuge today to specify this EXACT HSS‑G single‑cut tap for production or repair tasks — advisers at Metav Werkzeuge can confirm machine compatibility and recommend the correct holder or torque setting, phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: 4000867576NW Product name: Single‑cut thread tap HSS‑G M6 x 18 mm (EXACT) Brand: EXACT GmbH & Co. KG Präzisionswerkzeuge Facts Thread length: 18 mm Overall length: 39 mm Hex shank: 6.3 mm (1/4") to DIN 3126 Packaging unit: 1 Special features Material: HSS‑G (ground high‑speed steel) Chamfer: 4–5‑cut chamfer Self‑centring geometry 6‑sided drive (6.3 mm / 1/4") for quick change systems FAQ What thread size does this tap produce? The tool produces metric M6 threads, specified as M6 x 18 mm thread length for reliable engagement in standard assemblies. Is the shank compatible with quick‑change holders? Yes — the 6.3 mm (1/4") hex shank to DIN 3126 fits common quick‑change holders and power drivers used in industrial and workshop settings. What material is the tap manufactured from? The tap is made from HSS‑G (ground high‑speed steel), chosen for edge stability and consistent cutting performance. What benefit does the self‑centring feature provide? The self‑centring geometry assists initial alignment in the hole, reducing the likelihood of cross‑threading and improving the first‑pass success rate with the EXACT single‑cut tap. How long is the tool overall and what is the lead‑in like? Overall length is 39 mm, with a 4–5‑cut chamfer to ease lead‑in and support controlled chip flow during the start of the thread Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a hard-wearing HSS‑Co cutting material and a straight‑fluted Form B design to achieve consistent, ISO‑compliant M6×1 threads in steels up to approx. 900 N/mm²; order directly via Metav Werkzeuge or consult the Metav team for technical advice. Single‑flute tap DIN 352 Form B M6×1 HSS‑Co ISO2 (6H) – TECWERK The single‑flute tap DIN 352 Form B M6×1 is a straight‑fluted cutting tap designed for producing precise metric ISO threads, particularly suited to through‑threading in medium‑strength steels. HSS‑Co for high wear resistance Straight‑fluted Form B geometry ISO2 (6H) tolerance for metric threads High performance and long tool life for medium‑strength steels The use of HSS‑Co (cobalt‑alloyed high‑speed steel) increases hot hardness and wear resistance compared with standard HSS, which translates into longer service life under continuous production conditions. The tap is specified for steels up to approx. 900 N/mm² tensile strength, so the material choice ensures reliable cutting action where ordinary HSS would wear prematurely. This results in fewer tool changes and more predictable process windows, supporting efficient batch production and maintenance work alike. Consistent, interchangeable metric threads to ISO2 (6H) Designed to the DIN 352 Form B standard and compliant with DIN 13 Blatt 1, the tap produces M6×1 metric threads to the ISO2 (6H) tolerance field. This guarantees dimensional compatibility with standard fasteners and mating parts, reducing fitment issues in assemblies. The integrated cutting chamfer for through threads improves initial engagement and reduces the risk of cross‑threading when working with through holes, providing a dependable outcome for both series manufacture and repair applications. Geometry engineered for chip control and breakage safety The straight‑fluted Form B geometry combined with the single‑cut design helps control chip formation and evacuation in through‑threading operations. Flank relief (hinterschliffen) reduces radial contact and cutting forces, which lowers the likelihood of tap breakage under intermittent loading. Although the tool is uncoated, the cobalt alloy compensates by offering improved durability; the uncoated surface also facilitates straightforward resharpening when required, extending the useful life of the tool in a cost‑effective way. Practical suitability and workshop considerations This tap is particularly well suited to workshops, maintenance departments and production facilities that require repeatable metric threads with minimal setup complexity. As an uncoated HSS‑Co tool, it performs best with appropriate cutting fluid and controlled feed to maximise tool life and surface finish. Supplied as a single unit (packaging unit: 1), it integrates easily into existing tooling inventories and is a practical choice for both occasional repairs and regular production runs. Choose the TECWERK single‑flute HSS‑Co tap for reliable M6×1 threading and contact Metav Werkzeuge for procurement and technical recommendations tailored to the application. Technical data Article number: 2000867325NW Product: Single‑flute tap DIN 352 Form B M6×1 HSS‑Co ISO2 (6H) TECWERK Manufacturer: TECWERK Facts Thread size: M6×1 Strength capacity: up to approx. 900 N/mm² Tolerance: ISO2 (6H) Standard: DIN 352; DIN 13 Blatt 1 Packaging unit: 1 Special features Cutting material: HSS‑Co Flute style: straight‑fluted (Form B) Flank relief (hinterschliffen) Cutting chamfer for through threads (Schälanschnitt) Uncoated Metric ISO thread FAQ What materials can this tap machine through? The TECWERK single‑flute tap is specified for use in steels up to approx. 900 N/mm² and is therefore suitable for many common construction and alloy steels. Does the tap produce standard tolerances for interchangeable threads? Yes — the tool cuts metric threads to ISO2 (6H) tolerance in accordance with DIN 13 Blatt 1, ensuring compatibility with standard fasteners. Is the tap coated or suitable for regrinding? The tap is uncoated and made from HSS‑Co, which allows straightforward regrinding when edge restore is needed while delivering increased hot hardness during use. What advantage does the straight‑fluted Form B offer? The straight‑fluted Form B design aids chip control in through‑threading, simplifies chip evacuation and, combined with flank relief, helps reduce cutting forces and tap breakage. Is this tap suitable for blind holes or only through holes? The tool features a cutting chamfer optimised for through threads, but it may be used in other applications provided cutting conditions and chip evacuation are carefully managed. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Reliable, precise thread making for metric components thanks to HSS‑Co cutting material and flank‑honed edges; ideal where consistent ISO2 (6H) tolerances and through‑thread performance are required. Order directly via Metav Werkzeuge or consult the specialists for application advice. Single‑flute thread tap DIN 352 Form B M8 x 1.25 – HSS‑Co, ISO2 (6H) by TECWERK The Single‑flute thread tap DIN 352 Form B M8 x 1.25 is a straight‑flute metric tap designed for cutting through threads in medium‑strength steels with consistent tolerance and reliable chip evacuation HSS‑Co alloy for high wear resistance Straight‑flute (Form B) for stable cutting Flank honed for improved thread fit Designed for through threads in steel up to 900 N/mm² Consistent industrial tolerances for repeatable assemblies The tap delivers ISO2 (6H) tolerance class threads, ensuring interchangeability and secure fits in production environments. The flank honed geometry reduces burr formation and improves thread engagement, which translates into fewer rejects and reduced rework. For users less familiar with tolerance classes: ISO2 (6H) denotes a standardised internal thread accuracy commonly specified for metric fastenings in mechanical assemblies. The straight‑flute design keeps the cutting action stable, while the single‑flute geometry supports controlled chip flow during through‑hole tapping. Durable performance for demanding steel applications Manufactured from HSS‑Co, the tool offers elevated red‑hardness and wear resistance compared with conventional high‑speed steels, extending tool life under sustained production. The tap is suitable for use in steels up to approx. 900 N/mm² tensile strength and is supplied uncoated, allowing compatibility with a range of cutting fluids. The integrated cutting chamfer for through threads promotes reliable entry and smooth chip breakage, reducing torque peaks and enhancing process stability on semi‑automated and manual tapping operations. Practical integration into workshop and production processes The straight‑flute, single‑cut configuration simplifies machining setups and is particularly effective in dedicated tapping stations and smaller toolrooms where repeatability is key. The combination of material and edge preparation supports consistent cycle times and predictable maintenance intervals, aiding planning and inventory management. For organisations seeking consolidated sourcing of precision tools, Metav Werkzeuge provides centralised supply and technical guidance, backed by a broad product range that reduces procurement complexity and supports steady production throughput. Contact Metav Werkzeuge for tailored application advice and to secure the TECWERK M8 x 1.25 single‑flute tap; local stock and specialist support are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867326NW SKU: 2000867326NW Label: Einschnittgewindebohrer DIN 352 Form B M8x1,25mm HSS‑Co ISO2 (6H) TECWERK Packaging unit: 1 Facts Thread: M8 x 1.25 Tolerance: ISO2 (6H) Material: HSS‑Co Suitable for steels up to approx. 900 N/mm² Special features Form B, straight‑flute Flank honed Metric ISO thread, DIN 13 sheet 1 With cutting chamfer for through threads Uncoated FAQ What materials is this tap suitable for? The TECWERK single‑flute tap is intended primarily for steels and is specified for use in materials up to approximately 900 N/mm² tensile strength. What does ISO2 (6H) mean for thread quality? ISO2 (6H) denotes a standard internal thread tolerance ensuring consistent fit and interchangeability; the tap is ground and honed to achieve this class for reliable assembly. Is the tap coated for enhanced wear resistance? This tool is supplied uncoated; wear resistance is achieved through the HSS‑Co substrate and the flank‑honed cutting edges. Can the tap be used for blind holes or only through holes? The geometry includes a cutting chamfer optimised for through threads; use in blind holes should consider chip evacuation and may require process adaptation. What is the packaging unit and how is the product identified? The article is supplied as a single item (packaging unit 1) and is identified by the article number 2000867326NW Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund