Take advantage of the combination of precise Whitworth pipe threading, robust HSS construction and a closed, pre-slotted Form B for consistent production results; order original tooling via Metav Werkzeuge or consult our specialists for application advice. TECWERK Round Die Form B G 3/4" x 14 HSS A – Whitworth pipe thread, HSS The TECWERK Round Die Form B G 3/4" x 14 HSS A is a solid cutting die for producing Whitworth pipe threads to DIN ISO 228, engineered for reliable performance when machining steels up to approximately 800 N/mm². HSS for long tool life and wear resistance Whitworth pipe thread G 3/4" x 14 per DIN ISO 228 Tolerance field A for consistent thread accuracy Closed, pre-slotted Form B for stable cutting High-accuracy threads that reduce assembly rework The enclosed cutting geometry is designed to deliver consistent thread accuracy, which reduces the need for post-process corrections and minimises assembly rework. Compliance with DIN ISO 228 and the designation tolerance field A mean the threads meet recognised industrial limits for fit and function. For workshops and production lines that require repeatable results, the die’s specification provides a verifiable basis for purchase decisions and quality planning. Durable HSS construction for extended service life Manufactured from HSS, the tool offers elevated hardness and toughness for demanding shop-floor use; the material choice supports machining at higher cutting forces and improves resistance to abrasive wear. The closed, pre-slotted Form B balances load distribution during cutting, which helps preserve flank geometry and extends usable life. Where tooling longevity is a factor in total cost calculations, this die delivers a reliable performance-to-cost ratio. Practical design for standard pipe-thread applications Configured for the Whitworth pipe thread G 3/4" x 14, this round die suits common hydraulic and plumbing thread requirements and is compatible with standard die stocks for hand or machine-assisted threading. The nominal height 16 mm provides stable engagement with the workpiece while the pre-slotted construction facilitates chip evacuation and reduces risk of jamming. The tool is specified for machining steels up to ≈800 N/mm², making it suitable for a broad range of general-steel components. For specification checks, application advice or to obtain original TECWERK threading tools, contact Metav Werkzeuge in Emmerich for reliable supply and expert guidance. Technical data Article number: 2000867784NW UID: 2000867784NW Manufacturer: TECWERK Facts Thread profile: Whitworth pipe thread G 3/4" x 14 TPI, per DIN ISO 228 Standard: DIN EN 24231 Material: HSS Form: B Height: 16 mm Tolerance: Tolerance field A Suitable for steels up to approx. 800 N/mm² Special features Closed, pre-slotted design (Form B) Tolerance field A for precise threads For machining steel up to ≈800 N/mm² Packaging unit: 1 FAQ What thread standard does this die produce? This die cuts Whitworth pipe threads to DIN ISO 228 specifications, producing a G 3/4" x 14 profile suitable for standard pipe fittings. Which materials can be machined with the TECWERK Round Die? The TECWERK Round Die Form B G 3/4" x 14 HSS A is specified for use on steels up to approximately 800 N/mm² tensile strength. Is the die suitable for production environments? Yes; the HSS construction and closed, pre-slotted Form B design provide durability and stable cutting behaviour for workshop and light production use. How does tolerance field A affect assembly? Threads produced to tolerance field A offer close dimensional control and consistent fit, which supports reliable connections and reduces the likelihood of leaks or loose assemblies. What is the physical height of the die and why does it matter? The die has a height of 16 mm, which ensures sufficient engagement for accurate thread formation and helps maintain alignment during hand or machine threading. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a durable HSS cutting edge and precise tolerance class for reliable pipe-thread production—combine robust tool life with straightforward handling for consistent workshop output. Order directly via Metav Werkzeuge or consult our specialists for technical advice. TECWERK round die G 3/8 in x19, HSS, Form B The TECWERK round die G 3/8 in x19 HSS Form B is a closed, pre-slit die designed for cutting Whitworth pipe threads in medium-strength steels for industrial and repair applications. High-speed steel (HSS) cutting material Whitworth pipe thread G 3/8 in x19 to DIN ISO 228 Form B: closed, pre-slit construction Tolerance class A for accurate thread quality Thread accuracy that reduces rework and downtime This tool delivers consistent, high-precision threads thanks to its tolerance class A specification and conformity with DIN EN 24231. Designed for the Whitworth pipe thread form, the die produces parallel pipe threads to DIN ISO 228, ensuring compatibility with standard pipe fittings and connectors. The combination of a hardened cutting material and a defined tolerance band means fewer rejects and reduced post-process corrections, improving throughput in maintenance and small-batch production. Durable geometry for repetitive workshop use Manufactured from HSS, the round die resists wear across extended runs and preserves cutting edges under typical workshop conditions. The Form B design—closed with a pre-slit section—supports controlled chip formation and improved centring in the die stock, which helps maintain concentricity and reduces the likelihood of cross-threading. With a compact height of 14 mm, the tool is suited to standard die-holders and hand-operated stations, offering straightforward integration into existing workflows. Practical benefits that support operational efficiency Using a die with HSS construction and a proven thread standard offers a cost-effective balance between tool life and machining quality. The robust design minimises the frequency of tool changes, while the precise thread geometry reduces the need for subsequent adjustments. For workshops aiming to standardise consumables, this die provides a repeatable solution for pipework repair and assembly, contributing to predictable maintenance cycles and lower indirect labour costs. What to expect in use and care The die is specified for machining steels with tensile strengths up to approximately 800 N/mm², so it is well suited for common structural and engineering steels encountered in fabrication and repair environments. To preserve cutting performance, standard workshop practice such as appropriate die-holder selection, controlled feed, and suitable cutting fluid is recommended. As the tool is engineered for parallel pipe threads, it is not intended for tapered-thread applications. For reliable pipe-thread production choose the TECWERK round die and contact Metav Werkzeuge for tailored advice and supply from Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000867782NW Product name: Schneideisen Form B G 3/8 Zollx19 HSS A TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Thread size: G 3/8 in x19 Height: 14 mm Suitable tensile strength: up to approx. 800 N/mm² Tolerance: class A Special features Material: HSS Standard: DIN EN 24231 Thread form: Whitworth pipe thread to DIN ISO 228 Form: B, closed and pre-slit FAQ What thread standard does this die produce? The TECWERK round die G 3/8 in x19 produces Whitworth pipe threads to DIN ISO 228, ensuring standardised parallel pipe-thread profiles for fittings. Which materials is the die intended for? This TECWERK die is specified for use on steels with tensile strengths up to approximately 800 N/mm², making it suitable for most common engineering steels. What are the practical advantages of Form B construction? Form B in this TECWERK die denotes a closed, pre-slit design that improves chip control and centring, which helps achieve more consistent thread runs and reduces the chance of cross-threading. What does tolerance class A mean for thread fit? Tolerance class A on the TECWERK round die indicates a tighter dimensional window for the thread form, delivering a more accurate and reliable fit for standard pipe connections. Can this die be used for tapered threads? No; the TECWERK round die G 3/8 in x19 is intended for parallel Whitworth pipe threads (G) in accordance with DIN ISO 228 and is not suitable for tapered thread forms. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of DIN 225 conformity, robust zinc die-cast construction and compact 10 mm height for reliable die mounting; order the TECWERK threading die holder directly via Metav Werkzeuge or consult our specialists for application advice. Threading die holder DIN 225 — TECWERK (zinc die-cast, 38 mm) The threading die holder DIN 225 secures closed and slotted dies for dependable thread cutting in workshop, maintenance and production settings. Conforms to DIN 225 standard Zinc die-cast construction Includes screws and a screw-in handle Precise die support for consistent thread cutting The holder offers secure clamping in accordance with DIN 225, ensuring repeatable alignment when turning external threads. Thanks to the centring for a 38 mm diameter die and the low 10 mm body height, the design minimises runout and supports consistent cutting geometry. This reduces rework and cycle time by keeping the die concentric to the workpiece, which is particularly important for small-batch production and maintenance tasks where thread quality must be reproducible. Durable build and straightforward handling in the workshop Manufactured from zinc die-cast, the component combines corrosion resistance with dimensional stability for everyday use. The included screws and a screw-in handle allow quick fitting of both closed and slotted dies so that set-up time is reduced and handling is intuitive for trained staff. The overall length of 315 mm provides comfortable leverage without excessive bulk, making the tool practical for bench work and portable applications alike. Compatibility, standards and practical application Designed to accept standard dies made to the same norm, the accessory accommodates a broad range of common thread sizes when used with compatible dies; compatibility is governed by the DIN 225 specification. The compact profile supports access in confined spaces while the robust material tolerates routine workshop stresses. For teams standardising tooling across multiple workstations, the holder offers a simple, standardised interface that integrates with existing die assortments. For secure, standards-compliant die mounting, request the TECWERK threading die holder from Metav Werkzeuge — contact our product advisors at info@metav-werkzeuge.com or call +49 2822 7131930 for ordering or technical guidance. Technical data Article number: 2000867875NW Product name: Threading die holder DIN 225, 38 mm, 10 mm height, zinc die-cast Manufacturer: TECWERK Facts Height: 10 mm Overall length: 315 mm Diameter: 38 mm Standard: DIN 225 Special features Material: zinc die-cast Includes screws and a screw-in handle Accepts closed and slotted dies FAQ What dies does the holder accept? The threading die holder accepts closed and slotted dies manufactured to the DIN 225 specification and sized for a 38 mm mounting diameter. Is the die holder suitable for regular workshop use? Yes — the zinc die-cast construction and included screws make the TECWERK die holder suitable for routine workshop and maintenance operations. How much length does the holder provide for leverage? The holder has an overall length of 315 mm, designed to offer practical leverage without compromising manoeuvrability at the bench. Does the product include fastening hardware? Yes; the delivery includes the required screws and a screw-in handle for die installation and removal. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of DIN 225 conformity, zinc die-cast construction and simple die retention for reliable external threading in workshop and industrial settings; order the die holder directly via Metav Werkzeuge or ask the consultants if needed. Threading die holder DIN 225 – Zinc die-cast, 38 mm A robust threading die holder designed to accept closed and slotted dies for standard external threading tasks in workshops and maintenance workshops. DIN 225 compliance for standard threading Zinc die-cast body for stable holding Accepts closed and slotted threading dies Includes fixing screws and screw-in handle Consistent standard conformity for precise threads The holder is manufactured to DIN 225, ensuring compatibility with established external threading dies and predictable assembly workflows. Conformity to the norm reduces setup time and uncertainty when switching between die types, which supports a steady production pace. The standardised interface also simplifies inventory planning and spare-part procurement for maintenance teams and small production lines. Secure retention and easy handling Equipped with integrated fixing screws and a screw-in handle, the device offers straightforward securing of both closed dies and slotted dies. The fastening arrangement converts manual torque into reliable clamping without complex tools, improving handling speed and repeatability. For operators with limited bench space, the simple screw-in handle system shortens changeovers and lowers the risk of cross-threading during setup. Durable construction for everyday workshop use Produced from zinc die-cast, the holder balances rigidity with economical production, delivering consistent alignment under normal workshop loads. The metal alloy resists deformation during repeated use and provides a stable foundation for the die, which contributes to better thread form and tool life. Routine inspection and basic cleaning suffice to maintain performance, keeping maintenance overhead low. Practical dimensions and workshop integration With a total length of 315 mm and a working height of 14 mm, the holder provides secure leverage while remaining compact enough for bench or vice-mounted applications. The nominal die aperture of 38 mm accommodates commonly used die sizes, allowing easy integration into existing threading setups. Its straightforward form factor supports quick storage and transport between jobs without unnecessary bulk. For a reliable, DIN 225-compliant threading die holder by TECWERK and tailored advice from Metav Werkzeuge, contact Metav Werkzeuge in Emmerich for expert guidance and prompt supply. Technical Data Article number: 2000867876NW SKU/UID: 2000867876NW Manufacturer: TECWERK Packaging unit: 1 Facts Overall length: 315 mm Height: 14 mm Diameter: 38 mm Standard: DIN 225 Special features Material: zinc die-cast Includes fixing screws and screw-in handle Accepts closed and slotted dies Designed for external threading tasks FAQ Which die types fit this holder? The threading die holder accepts both closed and slotted dies and accommodates dies with a nominal diameter of 38 mm (TECWERK, SKU 2000867876NW). Is a handle included with the device? Yes, the delivery includes a screw-in handle and fixing screws for secure fastening of the die in the holder (TECWERK die holder, SKU 2000867876NW). What standard does the holder conform to? The tool is manufactured to DIN 225, ensuring compatibility with standard external threading dies and established workshop procedures. What material is the holder made from? The holder is made from zinc die-cast, chosen for stable clamping behaviour and economical durability in everyday workshop use. What are the key dimensions to consider for installation? Key dimensions are an overall length of 315 mm, a working height of 14 mm and a die aperture of 38 mm, which together define fit and leverage for bench or vice-mounted use. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Choose a standard-compliant solution with DIN 225 compatibility and a zinc die-cast body for reliable clamping and straightforward maintenance; take advantage of the 450 mm overall length for improved access and leverage. Order the die holder directly via Metav Werkzeuge or consult our advisors for application support. Die holder DIN 225, D 45 mm, H 18 mm – Zinc die-cast (TECWERK) The die holder DIN 225 secures closed and slotted round dies for workshop and industrial threading tasks. DIN 225 compatibility for standard round dies Zinc die-cast body for stable clamping Includes screws and screw-in handle for mounting Overall length 450 mm for extended reach Standardised clamping for consistent thread results The holder is built to the DIN 225 standard, which ensures consistent fit and secure seating of closed and slotted round dies. With the supplied screws and an screw-in handle, the unit enables quick die changes and a repeatable set-up, reducing downtime in production or repair work. This standard conformity simplifies tool selection and guarantees interchangeability with other DIN 225 tooling, supporting efficient workshop processes. Durable construction that reduces service interventions A zinc die-cast body provides dimensional stability and robust clamping under routine workshop conditions. The material choice balances stiffness and manufacturability, offering a corrosion-resistant surface finish compatible with everyday use. The 18 mm seating height ensures reliable die retention while limiting lateral play, which helps maintain thread quality over repeated cycles and reduces the need for frequent adjustments or replacements. Improved access and handling for faster operations The holder’s 45 mm diameter and 450 mm overall length deliver additional reach and leverage for manual threading tasks, making it easier to work in confined assemblies or deep fixtures. That extra length aids in applying consistent torque and improves line of sight to the die, supporting ergonomic handling and reducing operator fatigue. Supplied as a single unit, the item is ready to integrate into existing toolsets without additional conversions. Supply reliability and application advice from a specialist partner Backed by Metav’s position as a precision partner, this die holder benefits from a dependable distribution channel and quality screening in Emmerich. Metav’s range and technical competence mean that compatibility questions and accessory needs can be resolved quickly. For threading requirements where interchangeability and dependable clamping are essential, this holder represents a practical, standards-based choice that supports steady production flow. Contact Metav Werkzeuge for ordering or technical advice on the TECWERK die holder and ensure the selected holder matches the intended dies and applications Technical data Article number: 2000867878NW Description: Die holder DIN 225; includes screws and a screw-in handle Material: Zinc die-cast Standard: DIN 225 Numbers / Core data Diameter: 45 mm Height: 18 mm Overall length: 450 mm Packaging unit: 1 Special features / Versions For closed and slotted round dies (DIN 225) Incl. screws and screw-in handle for die clamping Zinc die-cast construction FAQ Which die types are compatible with this holder? The die holder complies with DIN 225 and accepts both closed and slotted round dies specified for that standard; the TECWERK die holder (SKU 2000867878NW) is therefore suitable for standard round-threading dies. Is the handle permanently attached or removable? The delivery includes a screw-in handle and fastening screws; the handle can be removed or replaced as required for storage or specific work setups. What advantages does the zinc die-cast body provide? Zinc die-cast offers dimensional stability and good wear resistance in workshop environments; the material supports consistent clamping and long service life for the die holder. Does the overall length improve usability for deep assemblies? Yes—the 450 mm overall length provides increased reach and leverage, making the holder advantageous for work in confined spaces or deeper fixtures. Is the product supplied ready to use? The item is supplied complete with screws and a screw-in handle and is packaged as a single unit, ready for immediate integration into existing toolsets. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combining DIN 225 compatibility, a zinc die-cast body and an integrated screw-in handle, this die holder provides a dependable, easy-to-fit solution for workshop threading tasks; order the item directly via Metav Werkzeuge or contact our consultants for tailored advice. Die holder DIN 225 D45 H14 – Zinc die-cast body, screw-in handle (TECWERK) A compact Die holder DIN 225 D45 H14 designed to accept closed and slotted round dies for precise manual threading and workshop repair applications. DIN 225 compatibility Zinc die-cast construction Includes screws and screw-in handle 450 mm overall length Consistent fit for standard round dies The holder is manufactured to the DIN 225 dimensioning, ensuring reliable alignment with standard round dies and making die selection straightforward for machining and maintenance operations. The 45 mm die capacity is specified to match common metric die sizes, so replacement dies conforming to DIN 225 fit without further modification. This compatibility reduces setup time and supports repeatable results when cutting external threads by hand. Secure clamping and straightforward handling Equipped with fastening screws and an internal, screw-in handle, the design secures both closed and slotted dies firmly during operation. The clamping mechanism is explained in simple terms: the screws compress the die in its seat while the handle provides leverage for controlled rotation. For workshop technicians who require dependable manual threading tools, these features deliver a combination of grip and handling that supports clean thread starts and steady feed. Durable materials for routine workshop use Constructed from zinc die-cast, the holder offers dimensional stability and resistance to everyday workshop conditions. Zinc die-cast components are commonly used where consistent shape and moderate mechanical strength are required, and the material selection here contributes to a stable die seat and long-term interchangeability. Regular inspection and light lubrication at the screw threads are recommended to preserve functionality and ease future die changes. Ready for immediate integration into workshop processes With an overall length of 450 mm and a compact height of 14 mm, the holder is sized for hand-operated threading tasks and for inclusion in general workshop supplies. The unit is supplied complete with the fastening screws and the screw-in handle for immediate use, enabling fast deployment on service benches, in maintenance workshops or for field repair work. Specification-focused documentation and product marking simplify inventory management and ordering. For delivery from Emmerich and technical guidance, contact Metav Werkzeuge for procurement and advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000867877NW Item: Die holder DIN 225 D45 H14 TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Overall length: 450 mm Height: 14 mm Die diameter capacity: 45 mm Standard: DIN 225 Materials & features Material: zinc die-cast Includes screws and screw-in handle Accepts closed and slotted dies FAQ Which die sizes fit this holder? The Die holder DIN 225 D45 H14 is specified for a 45 mm die capacity and is compatible with round dies made to DIN 225, SKU 2000867877NW. Are fastening screws and a handle included? Yes, the TECWERK die holder is supplied with the necessary screws and an screw-in handle, as stated for item 2000867877NW. What material is the holder made from and what does that mean for use? The body is zinc die-cast, providing dimensional stability suitable for routine workshop threading; the Die holder DIN 225 D45 H14 from TECWERK benefits from this material choice. Is the holder suitable for closed and slotted dies? The design accepts both closed and slotted dies, and the clamping screws secure either type in the seat—this functionality is built into item 2000867877NW. How is the product supplied for inventory purposes? The unit is packed with a packaging unit of 1; the product is listed under SKU 2000867877NW and labelled as Die holder DIN 225 D45 H14 (TECWERK). Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from a robust combination of zinc die‑cast construction and DIN 225 compatibility for dependable manual threading. The firm clamping of closed and slotted dies and the integrated screw‑in handle ensure straightforward die changes and consistent results — order the holder via Metav Werkzeuge or request technical advice from the consultants. Die holder DIN 225, D 55 mm, H 22 mm — TECWERK The Die holder DIN 225 is a compact die stock for secure clamping of closed and slotted round dies, designed for manual threading and maintenance tasks in workshop environments. Zinc die‑cast construction for long service life Conforms to DIN 225 for interchangeability Accepts closed and slotted dies for versatility Includes screws and screw‑in handle for quick fitting Consistent clamping for accurate thread cutting The die stock provides a stable platform for thread cutting thanks to its DIN 225 conformity and precise dimensions. The holder accepts dies with a nominal diameter of 55 mm, ensuring compatibility with standard round dies; the height 22 mm provides the necessary contact depth for a secure fit. With screws and a screw‑in handle, die changes are rapid and repeatable, reducing setup time and improving throughput in regular maintenance or small‑batch production operations. This contributes directly to reduced process variability and more predictable component quality. Durable construction that supports everyday workshop use Manufactured from zinc die‑cast, the holder combines corrosion resistance with sufficient rigidity for manual operations. The robust material choice balances durability with cost efficiency, making it suitable for general workshop environments where frequent handling occurs. The overall length 560 mm facilitates handling and provides appropriate leverage for controlled manual threading operations. These design decisions reduce the likelihood of premature wear and support long service intervals, which is particularly relevant for procurement planning and maintenance scheduling. Clear standardisation minimises compatibility issues Adherence to a recognised standard such as DIN 225 ensures straightforward integration into existing tooling sets and spare‑part inventories. The distinction between closed and slotted dies is practical: closed dies offer full‑bodied cutting for standard threads, while slotted dies allow slight adjustment and easier chip clearance. The holder’s compatibility with both types simplifies tooling selection and reduces the number of specialised holders required on the workbench, streamlining logistics and inventory management for maintenance departments and small industrial shops. Practical reliability and trusted supply chain Selection of this die stock supports operational reliability through simple, well‑understood mechanics rather than complex electronics, which aids in rapid fault diagnosis and repair. Combined with Metav’s role as a precision partner — offering a broad product range and dependable fulfilment from Emmerich — the choice helps maintain uninterrupted workshop operation. The combination of standard compliance, durable materials and straightforward mechanics delivers predictable performance and peace of mind for procurement and workshop managers alike. Contact Metav Werkzeuge for availability and technical guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — expert advice and reliable supply from Emmerich are available for this TECWERK die holder (SKU 2000867880NW) Technical data Article number: 2000867880NW Label: Die holder DIN 225, D 55 mm, H 22 mm Brand: TECWERK Packing unit: 1 Numbers Height: 22 mm Overall length: 560 mm Nominal die diameter: 55 mm Special features Material: zinc die‑cast Conforms to DIN 225 Includes screws and screw‑in handle; accepts closed and slotted dies FAQ Which die types fit this holder? The holder accepts both closed and slotted round dies according to DIN 225; compatibility covers dies with a nominal diameter of 55 mm as stated for the TECWERK die holder (SKU 2000867880NW). What material is the holder made from? The TECWERK die holder is made from zinc die‑cast, chosen for durability and good resistance to workshop conditions. Is the holder intended for manual use? The design, including a screw‑in handle and screws for die retention, is intended for manual threading tasks and maintenance work. What are the key dimensions to consider? Key dimensions are height 22 mm, overall length 560 mm and nominal die diameter 55 mm, which determine fit and handling characteristics. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a compact, standards‑compliant die holder that combines robust zinc die‑cast construction, compatibility with DIN 225 dies and a practical screw‑in handle for fast tool changes — order directly via Metav Werkzeuge or consult the team for tailored advice. Die holder DIN 225, Ø55 mm, zinc die‑cast — TECWERK The die holder DIN 225 secures closed and slotted dies for manual thread cutting and maintenance tasks in workshop environments, offering a reliable clamping solution for standard dies. DIN 225 compatibility for standard dies Zinc die‑cast body for workshop resilience Includes screws and screw‑in handle Total length 495 mm for good leverage Faster, standardised hand‑threading with proven clamping The TECWERK die holder follows DIN 225, ensuring straightforward fitment of conventional round dies. The unit accepts both closed and slotted dies, held securely by the supplied screws and the screw‑in handle, which together create a repeatable clamping action. This standard compliance reduces uncertainty in procurement and minimises inventory variants, while the measured Ø55 mm seating and 16 mm body height provide a clear, verifiable basis for selecting the correct tool for manual threading operations. Robust construction for everyday workshop use Manufactured from zinc die‑cast, the holder offers a balance of rigidity and corrosion resistance suited to regular use in workshops and service departments. The material choice gives a stable platform for cutting threads in ferrous and non‑ferrous components, and the compact body reduces bulk at the tool face. The 495 mm overall length increases leverage for manual operation without adding excessive weight, supporting comfortable handling during prolonged maintenance tasks and on‑site repairs. Quick setup and reduced process downtime The design incorporates an easily engageable screw‑in handle and fastening screws, allowing rapid replacement of round dies and secure locking during cutting. The simple mechanical clamping avoids complex adjustments and keeps changeover times low, contributing to higher throughput in small‑batch production or repair workflows. Where standardisation matters, the holder’s compatibility with DIN 225 dies helps streamline tool preparation and reduces the time spent searching for matching holders. Clear technical scope for purchasing and maintenance The die holder is a pragmatic choice for engineers specifying tools for manual thread cutting: it is a dedicated clamping device for round dies compliant with DIN 225, supplied ready to fit both slotted and solid dies. Routine inspection is limited to checking the condition of the screws and the seating for wear; replacement parts are standardised and easy to source. Procurement benefits from the transparent specification and from sourcing through an experienced supplier such as Metav Werkzeuge, which supports consistent supply and a broad product range for workshop needs. For workshop operators seeking a durable, standards‑compliant die holder from TECWERK, contact Metav Werkzeuge for supply and technical clarification via info@metav-werkzeuge.com or call +49 2822 7131930 — reliable delivery from Emmerich guaranteed. Technical data Article number: 2000867879NW Label: Schneideisenhalter DIN 225 D.55mm H.16mm Zinkdruckg.TECWERK Manufacturer: TECWERK Packaging unit: 1 Numbers / Facts Diameter: 55 mm Height: 16 mm Total length: 495 mm SKU / UID: 2000867879NW Special features / Versions DIN 225 compliance Zinc die‑cast material Includes screws and screw‑in handle Suitable for closed and slotted dies FAQ What standard does the holder follow and which dies fit? The holder is made to DIN 225 and accepts round closed and slotted dies, offering straightforward compatibility with standard thread‑cutting inserts. Is the handle and fastening hardware included? Yes — the delivery contains the screws and a screw‑in handle for secure clamping and easy die changes. What material is the holder made from and why is that important? The body is zinc die‑cast, chosen for a robust, corrosion‑resistant construction that suits repetitive workshop use and offers reliable seating for thread cutting. What are the key dimensions to check before ordering? Relevant dimensions are the Ø55 mm die seating, 16 mm body height and the 495 mm total length; these define fit and handling for manual operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combining DIN 225 compliance, die-cast zinc construction and included fastening hardware, this holder delivers reliable manual threading with quick die changes for everyday workshop use. Order the die holder directly via Metav Werkzeuge or consult the Metav specialists if clarification is required. Die holder DIN 225 – Ø 65 mm, 18 mm height (TECWERK) The Die holder DIN 225 secures closed and slotted round dies for standard manual threading tasks in workshop environments. DIN 225 compliant holder for standard round dies Accepts closed and slotted die designs Die-cast zinc construction for workshop durability Supplied with screws and screw-in handle Reliable compatibility with industry-standard dies The holder is built to the DIN 225 specification, which means it accepts standard round dies in both closed and slotted designs; this standardisation reduces tool incompatibilities and simplifies inventory choices. Because the accessory is designed for both solid and slotted types, operators benefit from flexible threading options without needing multiple specialised holders. The conformity to a recognised norm provides a clear basis for selecting the correct tool for routine maintenance and repair jobs. Engineered for stable handling and long service Manufactured from die-cast zinc, the assembly offers a stable clamping platform while remaining compact in form. With an overall length of 620 mm and a working height of 18 mm, the geometry supports controlled manual operation and secure die retention during cutting. The material choice balances rigidity with manageable weight, meaning the tool is robust enough for frequent use yet straightforward to handle during repeated thread-cutting cycles. This combination reduces the likelihood of slippage and uneven cuts. Simple setup and practical delivery scope The product is supplied complete with the required fastening screws and a screw-in handle, enabling immediate use after unpacking and minimising setup time. Quick die changes are facilitated by the straightforward clamping mechanism, which is particularly helpful in busy workshops where downtime must be minimised. The concise scope of delivery and clear conformity to standards make the holder a pragmatic option for maintenance technicians and small engineering shops seeking dependable manual threading equipment. For reliable supply and specification advice on this TECWERK die holder, contact Metav Werkzeuge for a tailored recommendation and prompt delivery from Emmerich. Technical Data Article number: 2000867881NW Manufacturer: TECWERK Description: Die holder DIN 225, accepts closed and slotted dies Material: die-cast zinc Total length: 620 mm Height: 18 mm Delivery scope: screws and screw-in handle Core specifications Diameter: 65 mm Height: 18 mm Total length: 620 mm Article number: 2000867881NW Features DIN 225 standard Accepts closed and slotted dies Supplied screws and screw-in handle Material: die-cast zinc FAQ What die types fit this holder? The holder is compatible with both closed (solid) and slotted round dies as stated for the die holder DIN 225 (TECWERK, SKU 2000867881NW), so both standard die designs can be used. Does the product meet any standard? Yes, the device conforms to DIN 225, which defines the dimensions and mounting for round die holders and ensures compatibility with standard threading dies. What material is the holder made from? The TECWERK die holder (2000867881NW) is made from die-cast zinc, chosen to provide a stable clamping body suitable for routine workshop use. Is the holder ready to use on delivery? The delivery includes fastening screws and a screw-in handle, enabling immediate assembly and use of the die holder DIN 225 without the need for additional parts. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the robust design and standard compliance of this die holder for reliable threading operations; the zinc die-cast construction and DIN 225 compatibility ensure repeatable results, and the supplied screws plus screw-in handle simplify mounting and changeover. Order directly via Metav Werkzeuge or consult the technical team for application guidance. Die holder DIN 225 – 65 mm zinc die‑cast by TECWERK The Die holder DIN 225 secures standard thread‑cutting dies for workshop and industrial threading applications, offering a sturdy mounting for both closed and slotted dies. Robust zinc die-cast construction Complies with DIN 225 standard Accepts closed and slotted dies Supplied with screws and screw-in handle Reliable, standardised mounting for consistent thread quality A purpose‑built die holder provides mechanical stability that reduces run‑out and helps maintain concentricity during manual threading. The DIN 225 conformity means the holder matches established dimensions and clamping positions, enabling predictable assembly with compatible dies. The zinc die‑cast body delivers dimensional accuracy and stable clamping under typical workshop conditions, which contributes to fewer rejects and less rework — a direct benefit to production efficiency and process reliability. Practical handling and accessories that speed up workflow The design includes a screw‑in handle and the necessary fastening screws, so dies in both closed and split configurations can be fitted quickly and held securely. The holder’s working dimensions — 65 mm diameter and a 25 mm height at the clamping section, combined with an overall length of 630 mm — provide effective leverage and reach for manual operations, while keeping the tool comfortable to control. Closed dies give fixed diameter cuts for repeatability, whereas slotted (split) dies allow slight adjustment of the thread fit; the holder accommodates both types without additional adaptors. Compatibility and durability for everyday workshop use Constructed from zinc die‑cast, the holder balances strength with manageable weight for handheld tasks; the material offers good dimensional stability and resistance to routine workshop wear. Conformance to the DIN standard ensures broad compatibility with metric dies made to the same specification, simplifying tool inventory and reducing downtime for setup. For those seeking reliable threading tools from a trusted distributor, Metav’s industrial supply background provides reassurance about availability and consistent quality. For tailored advice on DIN 225 threading equipment or to arrange supply from Metav Werkzeuge in Emmerich, contact info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance and reliable delivery. Technical data Article number: 2000867882NW Label: Die holder DIN 225 65 mm H 25 mm zinc die‑cast TECWERK Brand: TECWERK Packaging unit: 1 Dimensions & Size Diameter: 65 mm Height: 25 mm Total length: 630 mm Features Material: zinc die‑cast Standard: DIN 225 Includes screws and screw‑in handle Accepts closed and slotted dies FAQ What dies fit this holder? The die holder is designed for dies made to DIN 225, so both standard closed and slotted (split) metric dies manufactured to that norm will fit correctly. How is a die secured in the holder? Dies are clamped using the supplied screws and the integrated screw‑in handle; the fastenings hold closed or slotted dies in the zinc die‑cast seat to provide stable cutting conditions. Are the dimensions suitable for workshop threading tasks? Yes, the holder’s working section with a 65 mm diameter and 25 mm height, plus the 630 mm overall length, offers effective leverage and accessibility for common manual threading operations. Is the holder compatible with adjustable slotted dies? The construction accepts slotted dies and permits slight adjustment of thread fit when using the split die design; it accommodates both fixed and adjustable die types compliant with the standard. Can the supplied screws and handle be replaced if lost? Replacement of the fastening screws and handle is possible using equivalent parts; parts availability may depend on the supplier and the exact specifications of the original components. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Robust steel construction and compliance with DIN 225 deliver consistent, workshop-ready thread cutting; the 800 mm overall length and included screws with a screw-in handle simplify die mounting and speed setups. Order the die holder directly via Metav Werkzeuge or consult Metav’s advisors for specification support. Die holder DIN 225 D.75mm H.30mm — Steel, 800 mm (TECWERK) A Die holder DIN 225 D.75mm H.30mm designed for secure clamping of solid and slotted dies in manual threading applications and conventional workshop equipment. Standardised to DIN 225 for consistent compatibility Steel body with 30 mm height for durable clamping Includes screws and screw-in handle for fast assembly Reliable conformity reduces setup uncertainty The holder conforms to DIN 225, ensuring compatibility with standard solid and slotted dies and predictable alignment during manual threading operations. Standardisation removes guesswork when selecting accessories, so thread cutting tasks proceed with fewer adjustments. The 800 mm overall length provides extended reach where longer tool overhangs are required, while the die clearance and clamping geometry maintain concentricity for repeatable results. Heavy-duty build that limits maintenance intervals Manufactured from steel and specified with a 30 mm height, the tool offers a robust clamping interface that withstands workshop stresses and frequent handling. The substantial cross-section reduces deformation under torque, translating into longer service life and fewer interruptions for replacement. As a consequence, machining throughput is improved and downtime associated with holder failures is minimised, supporting more stable production cycles. Practical design for quick assembly and predictable performance Assembly is straightforward thanks to the supplied screws and screw-in handle, which permit rapid die exchange and secure fastening in both closed and slotted die designs. The simple mechanical concept enables toolroom staff to focus on the cutting task rather than complex setup. For applications requiring confirmation of fit or further technical data, Metav Werkzeuge provides specification support and can advise on integration into existing tool sets. Contact Metav Werkzeuge for tailored advice on integrating the TECWERK die holder into workshop tooling—email info@metav-werkzeuge.com or call +49 2822 7131930 to request detailed technical information or ordering assistance Technical Data Article number: 2000867884NW Product name: Die holder DIN 225 D.75mm H.30mm steel TECWERK Brand: TECWERK Facts Standard: DIN 225 Diameter: 75 mm Height: 30 mm Overall length: 800 mm Special features Material: steel Supplied with screws Supplied with screw-in handle Suitable for closed and slotted dies FAQ What dies are compatible with this holder? The die holder is compatible with standard solid and slotted dies according to DIN 225, allowing use with commonly available threading dies. Does the holder include mounting hardware? Yes, the TECWERK die holder is supplied with the required screws and a screw-in handle for secure and expedient assembly. What is the overall length and why does it matter? The 800 mm overall length provides extended reach for applications with greater overhang, improving accessibility without compromising clamping stability. Which material is used for the holder and what benefit does it provide? Constructed from steel, the holder offers a robust clamping interface that resists deformation under load and supports longer service intervals. Is this holder suitable for production workshop use? Designed to DIN 225 and built in steel, the holder delivers the repeatability and durability expected in workshop threading operations. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a compact, high-performance cutting solution with HSS construction and a 6g tolerance for repeatable fine-thread results. Order the die directly via Metav Werkzeuge or contact the consultants for technical clarification and availability. TECWERK MF6×0.75 HSS round die (Form B) — metric fine thread, 6g tolerance A TECWERK MF6×0.75 HSS round die designed for cutting external metric fine threads to DIN specification in common workshop steels. HSS high-speed steel construction Metric fine thread MF6×0.75 Tolerance field 6g, DIN 13 compliant Closed pre-slit Form B, 7 mm height Accurate metric fine threads for consistent assemblies The MF6×0.75 round die delivers metric ISO fine threads with a 6g tolerance that matches common assembly requirements. Conformity with DIN EN 22568 and DIN 13 MF ensures compatibility with standard components and diminishes the need for rework. The tool’s geometry is optimised for external threading tasks where a compact thread profile and predictable fit are required, supporting repeatable production results in small-batch and maintenance scenarios. Durable HSS construction for extended service life Manufactured from HSS (high-speed steel), the cutting material offers a balanced combination of hardness and toughness suitable for repetitive cutting operations. The substrate resists abrasive wear under typical workshop conditions, maintaining cutting edges longer than standard carbon-steel alternatives. This robustness contributes to lower downtime for tool changes and a reduced frequency of replacement, supporting efficient workshop planning and reliable throughput. Stable Form B design for controlled machining The Form B configuration features a closed, pre-slit design that stabilises the cutting action while accommodating chip flow. With a compact 7 mm height, the die provides a solid engagement length that reduces chatter and ensures a cleaner lead into the workpiece. The pre-slit relief assists chip evacuation and lowers the risk of seizure during interrupted cuts, resulting in more uniform surface finish and thread geometry on the finished external thread. Application scope and material suitability Specified for use in common steels, the tool is rated for materials up to approximately 800 N/mm² tensile strength, making it appropriate for a wide range of engineering steels encountered in maintenance and light production. The tool’s specification does not list specialised coatings; performance in softer non-ferrous materials will depend on cutting parameters and lubrication. For high-speed or abrasive applications, a review of cutting data and potential coated alternatives is recommended. Integration into workshop workflows The compact die fits established die holders and manual threading setups, supporting rapid replacement and straightforward handling. Its standardised thread form reduces inspection complexity and simplifies quality checks against existing gauges. For inventory rationalisation, keeping this metric fine die in stock can streamline repair tasks and short-run production where MF threads are regularly required. Standards, traceability and quality expectations Production to DIN EN 22568 and adherence to DIN 13 MF provide a clear standard basis for thread form, tolerance and interchangeability. The combination of standard conformity, HSS material and Form B configuration yields a reliable external-threading tool that aligns with common industrial expectations for repeatable fit and serviceability. Contact Metav Werkzeuge for availability, technical guidance and rapid supply of TECWERK thread cutting dies (SKU 2000867760NW) via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000867760NW Product name: Round die, metric fine thread MF6×0.75, HSS, 6g Manufacturer: TECWERK Packaging unit: 1 Facts Thread: MF6×0.75 mm Tolerance: 6g Height: 7 mm Suitable for steels up to approx. 800 N/mm² Standard: DIN EN 22568; DIN 13 MF Cutting material: HSS Special features Form: B Closed pre-slit design Metric ISO fine thread Designed for external threading FAQ What thread size and pitch does this die produce? The TECWERK MF6×0.75 HSS round die produces a metric fine external thread with a size of MF6 and a pitch of 0.75 mm (MF6×0.75), matching DIN 13 MF specifications. Which materials is the die suitable for? This round die is specified for use with steels up to approximately 800 N/mm² tensile strength; suitability for other materials depends on cutting parameters and lubrication. What does the 6g tolerance mean for assembly? Tolerance 6g indicates the external thread class for the die, providing a standard clearance and fit for mating internal threads produced to compatible tolerance classes. Is the die a slotted design and what is the benefit? The tool is a closed pre-slit Form B die; the pre-slit profile assists chip control and reduces the likelihood of seizure, while maintaining a stable cutting engagement. Which standards govern the thread form and production quality? Production and thread form are aligned with DIN EN 22568 and DIN 13 MF, ensuring standardised thread geometry and interchangeability for metric fine threads. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Precision and durability meet reliable thread quality: the HSS construction combined with the MF8×1 mm metric fine pitch and 6g tolerance delivers consistent, serviceable threads for steels up to 800 N/mm²; efficient chip control is achieved by the closed, pre-slit Form B design. Order the TECWERK die directly via Metav Werkzeuge or consult Metav’s specialists for application advice. TECWERK Threading Die MF8×1 mm (Form B · HSS · 6g) The TECWERK Threading Die MF8×1 mm is a Form B high-speed steel die designed for cutting metric ISO fine threads in components made from medium-strength steels, optimised for workshop and industrial threading tasks. High-speed steel (HSS) construction Metric fine thread MF8×1 mm ISO fine thread Tolerance field 6g for accurate fits For steels up to 800 N/mm² tensile strength Closed, pre-slit Form B design Consistent precision for critical assemblies The die is manufactured to DIN EN 22568 standards and is specified for a MF8×1 mm metric fine pitch with tolerance 6g, which supports repeatable thread geometry and predictable fit behaviour in mating parts. The high-speed steel body provides dimensional stability under cutting loads and heat, reducing the risk of thread distortion. For production environments where interchangeability and consistent torque settings matter, this tooling choice minimises rework and rejects by ensuring the thread form conforms to established ISO fine-thread tolerances. Robust performance across common steel grades Designed for use in steels up to 800 N/mm² tensile strength, the die handles a broad range of typical workshop materials without rapid wear. The HSS cutting edges retain hardness at elevated temperatures and are therefore suitable for moderate duty threading where carbide would be excessive. The combination of Form B geometry and a closed, pre-slit layout improves chip control and contributes to even load distribution across the cutting flutes. This results in smoother cuts and reduced risk of thread damage when used with appropriate die stocks or holders. Practical handling and long-term reliability With a nominal height of 9 mm and a compact design, the die fits standard die holders and simplifies replacement cycles in busy shops. The pre-slit construction eases thread entry and improves chip evacuation compared with fully closed dies while maintaining the stability of a closed form for finish quality. Routine light sharpening and correct lubrication extend service life; the material choice and manufacturing standard make the component a practical option for workshops seeking a balance of durability and consistent finish without over-specification. Contact Metav Werkzeuge for tailored application support or to secure immediate supply of the TECWERK threading die from our Emmerich facility. Technical data Article number: 2000867762NW Manufacturer: TECWERK Label: Schneideisen Form B metrisch fein MF8x1mm HSS 6g TECWERK Facts Thread: MF8x1 mm Standard: DIN EN 22568 Tolerance: 6g Material: HSS Height: 9 mm Application: steels up to 800 N/mm² Special features Form: B, closed, pre-slit Metric ISO fine thread DIN 13 MF For workshop and industrial threading Packaging unit: 1 FAQ What material is the die made from and what does that mean for service life? The die is manufactured from HSS; HSS provides good wear resistance and heat tolerance, so the TECWERK die maintains cutting performance over extended use under typical workshop conditions. Which thread standard and tolerance does this die follow? This die conforms to DIN EN 22568 and produces a metric ISO fine thread MF8×1 mm with a tolerance field of 6g, ensuring compatibility with standardised mating parts. Can the die be used on hardened steels? The die is specified for steels up to approximately 800 N/mm² tensile strength; it is not intended for high-hardened steels beyond this range without specialist treatment or alternative tooling. How does the Form B, closed pre-slit design affect performance? The closed, pre-slit Form B shape offers a stable cutting form with improved chip control compared to fully closed types, leading to cleaner thread profiles and reduced jamming. What holder is required for this die and how is it installed? Standard die holders suitable for metric dies accept this form; the compact 9 mm height and conventional form mean the TECWERK die fits common die stocks used in workshops. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combining high-speed steel cutting performance, a 6g tolerance and the closed, pre-slotted Form B design ensures reliable, repeatable metric fine threads for demanding workshop use; order directly via Metav Werkzeuge or contact our consultants for specification support. TECWERK Form B Die — Metric fine thread MF8×0.75 mm, HSS, 6g A TECWERK Form B die for cutting metric ISO fine threads MF8×0.75 mm, engineered for precise fits in medium-strength steels and standardised to DIN EN 22568. Solid HSS construction Metric ISO fine thread MF8×0.75 Tolerance 6g for precise fits Suitable for steels up to 800 N/mm² Consistent thread accuracy for assembly reliability The round threading die delivers repeatable results through its 6g tolerance, meeting the expectations of fine-thread assemblies. The metric ISO specification (DIN 13 MF) and conformity with DIN EN 22568 provide a clear reference for compatibility with mating components, reducing rework and assembly time. For production and maintenance environments where thread fit affects sealing or torque behaviour, this tool supports consistent joint performance and predictable mechanical behaviour. Robust HSS build for demanding steel work Manufactured from HSS (high-speed steel), the die is intended for use in steels up to approximately 800 N/mm² tensile strength, offering a balance between wear resistance and toughness. The choice of HSS ensures heat resistance during intermittent heavy use and preserves cutting geometry over longer runs compared with softer steels. Correctly maintained, the tool supports reliable productivity and reduces replacement frequency, contributing to lower total operational costs over time. Form B design improves chip control and start-up The Form B configuration, supplied as a closed, pre-slotted die with a height of 9 mm, simplifies threading starts and improves chip evacuation compared with fully closed dies. The pre-slotted geometry eases initial alignment in a die holder and reduces the risk of cross-threading on delicate workpieces, while the closed nature ensures guidance and concentricity during manual threading. This combination makes the tool suitable for precision repair tasks and finer mechanical assemblies where thread quality is critical. Practical selection and workshop integration Selection is streamlined by the clear specification: MF8×0.75 mm, Form B, HSS, and 6g tolerance. The die is supplied singularly as a packaged unit, suitable for direct inclusion in a technician’s tooling kit or estate inventory. For operations standardising tooling across multiple workstations, adopting dies with documented standards aids quality assurance processes and simplifies inspection records. Contact Metav Werkzeuge today to discuss the TECWERK HSS Form B die (MF8×0.75 mm, 6g) and arrange delivery from our Emmerich stock or request detailed technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000867761NW UID: 2000867761NW Manufacturer: TECWERK Packaging unit: 1 Label: Schneideisen Form B metrisch fein MF8x0,75mm HSS 6g TECWERK Core data Thread: MF8×0.75 mm Tolerance: 6g Height: 9 mm Material: HSS Standard: DIN EN 22568 Suitable for steels up to approx. 800 N/mm² Special features Form: B Closed, pre-slotted form Metric ISO fine thread (DIN 13 MF) Solid HSS cutting material FAQ What materials is the die suitable for? The TECWERK Form B die is specified for use in steels up to approximately 800 N/mm² tensile strength, as stated in the product data. Which thread standard and size does this die produce? This tool cuts a metric ISO fine thread MF8×0.75 mm (DIN 13 MF) with a tolerance class of 6g. How does the Form B geometry affect threading? The closed, pre-slotted Form B die offers guided cutting and improved chip control, aiding start-up and reducing the chance of cross-threading. What cutting material and standard apply to this product? The die is manufactured from HSS and conforms to DIN EN 22568, ensuring consistent material and production standards. How is the item supplied? The product is supplied as a single packaged unit; the article number is 2000867761NW for ordering and inventory purposes. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the DIN 225 compatibility, solid steel construction and the extended 900 mm overall length for reliable, accurate manual thread cutting; order the die holder directly via Metav Werkzeuge or consult our specialists if further information is required. Die holder DIN 225, D 90 mm, H 36 mm (steel) – TECWERK — robust holder for closed and slotted dies, 900 mm overall length Die holder DIN 225, D 90 mm, H 36 mm (steel) – TECWERK is a hand-operated tool for secure mounting of closed and slotted dies in manual threading and repair tasks DIN 225 compatible die holder Accepts closed and slotted dies Solid steel construction, H 36 mm 900 mm overall length for extended reach Precise clamping for consistent thread quality The holder provides a stable platform for manual die threading thanks to its DIN 225 conformity and integrated clamping components. Fitted with screws and a screw-in handle, the device ensures firm die clamping, which reduces wobble and runout during use. This mechanical stability translates into more consistent thread profiles and fewer rework cycles, improving throughput in repair shops and maintenance departments. As a result, the tool supports efficient operations where repeatable accuracy is required. Compatibility and standards for workshop integration Designed to accept both closed and slotted dies, the holder covers common die types used across metalworking and maintenance applications. The adherence to DIN 225 simplifies tool selection and replacement in environments that follow international standards, allowing easy integration into existing tooling sets. Constructed from steel with a height of 36 mm, the holder offers a durable interface between the operator and the workpiece, minimising wear and ensuring long service life under regular workshop conditions. Design that improves reach and ergonomics With an overall length of 900 mm, the holder extends reach for threading tasks in deeper or recessed assemblies where compact holders fall short. The screw-in handle provides a secure grip and enables controlled torque transmission during cutting, reducing operator fatigue and improving safety. The straightforward mechanical design requires no electronics or calibration, so the tool remains ready for immediate use and needs only routine inspection to maintain performance. Practical handling, maintenance and workshop benefits The uncomplicated construction of the holder means maintenance is limited to checking the screws and cleaning swarf from the clamping area; this keeps downtime low and total cost of ownership competitive. The steel construction withstands workshop stresses and supports reliable manual thread cutting over time. For teams requiring predictable results, the combination of standard compliance, robust materials and simple operation makes this holder a practical investment for production support, maintenance shops and tool rooms. For robust manual threading with TECWERK quality, request the die holder via Metav Werkzeuge or contact our advisors at info@metav-werkzeuge.com or +49 2822 7131930 for tailored guidance Technical data Article number: 2000867886NW Product: Die holder DIN 225, D 90 mm, H 36 mm, steel Manufacturer: TECWERK Key specifications Height: 36 mm Overall length: 900 mm Diameter: 90 mm Standard: DIN 225 Special features Accepts closed and slotted dies Incl. screws and screw-in handle for die clamping Material: Steel FAQ What die types are compatible with this holder? The holder accepts both closed and slotted dies; the design conforms to DIN 225 to ensure compatibility with standard die formats and secure mounting for manual threading tasks. Is the construction suitable for heavy workshop use? Yes, the steel construction and robust clamping via screws and a screw-in handle make the holder durable for regular workshop and maintenance applications. What reach does the holder provide for recessed threading operations? The overall length of 900 mm provides extended reach for threading in deeper assemblies where shorter holders cannot access the workpiece effectively. Which article number identifies this product for ordering? The product is listed under article number 2000867886NW and is offered by TECWERK for standard die-holding requirements. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

A hard-wearing HSS round die in Form B delivers precise metric ISO threads with a stable, closed pre-slit design and a reliable 6g tolerance for secure assemblies in steels up to ~800 N/mm²; benefit from repeatable accuracy and robust tool life. Order the M10 x 1.5 HSS round die (Form B) directly via Metav Werkzeuge or ask our consultants if needed. M10 x 1.5 mm HSS Round Die (Form B) – 6g tolerance, TECWERK M10 x 1.5 mm HSS round die Form B by TECWERK for metric ISO external threading in medium-strength steels HSS for long tool life Metric ISO thread to DIN 13 Tolerance field 6g for precise fit Closed, pre-slit Form B design Precision threads that keep assemblies dependable The M10 x 1.5 mm round die provides consistent external threads according to metric ISO standards, helping maintain mechanical integrity across repetitive production or maintenance tasks. With a 6g tolerance, the die produces fits that balance manufacturability and functional clearance, reducing the need for post-threading rework. The use of High-Speed Steel (HSS) ensures that the cutting edges retain hardness at elevated temperatures, which translates into longer tool life and fewer replacements in busy workshops and service departments. Stable cutting geometry for clean thread profiles Form B’s closed, pre-slit design offers a stable cutting geometry that supports uniform thread profiles and reduced vibration during cutting. The pre-slit condition assists in controlled chip formation while maintaining the structural strength of the die body, which is especially beneficial when machining materials with tensile strengths up to around 800 N/mm². This combination of features yields improved surface finish and dimensional stability, making the component suitable for standard maintenance, mechanical repair and light production tasks where reproducibility is essential. Standards and material compatibility for industrial use Manufactured to DIN EN 22568 and compatible with DIN 13 thread specifications, the tool follows recognised norms for metric ISO threads, simplifying process documentation and quality assurance. Its suitability for steels up to the stated tensile strength makes it a practical choice for general engineering workshops, service technicians and in-plant maintenance teams. The designation 6g indicates a medium-fit tolerance class, which is commonly required where reliable mating with bolts and studs is necessary without demanding customised adjustments. Practical handling and integration into the workplace With a profile height of 11 mm, the die integrates easily into standard holders and die stocks used across most workshops; the packaging unit of 1 makes inventory straightforward for small-batch needs or replenishment stock. The die’s HSS cutting material supports resharpening in some service environments and offers a dependable cost-to-performance ratio for everyday threading tasks. When combined with proper lubrication and the correct die holder, the tool contributes to predictable cycle times and reduced scrap rates, supporting smoother workflows on the shop floor. Contact Metav Werkzeuge for application advice and to secure the TECWERK M10 x 1.5 HSS round die with swift supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000867740NW Item: M10 x 1.5 mm HSS round die Form B, TECWERK Brand: TECWERK Packaging unit: 1 Core facts Size: M10 x 1.5 mm Height: 11 mm Tolerance: 6g Material: HSS (high-speed steel) Standard: DIN EN 22568, DIN 13 Suitable for steels up to approx. 800 N/mm² Special features Form B – closed, pre-slit design Metric ISO thread cutting tool For external threading applications Single-piece packaging FAQ What thread form and size does this die produce? The TECWERK round die produces an M10 x 1.5 mm metric ISO external thread according to DIN 13 specifications. Which materials can be machined with this die? The die is made of HSS and is suitable for machining steels up to approximately 800 N/mm² tensile strength. What tolerance class does the die deliver? Threads cut with this die conform to a 6g tolerance, providing a medium-fit clearance suitable for standard bolted connections. Is this die suitable for production and workshop maintenance? Yes; the closed, pre-slit Form B design and HSS construction make it appropriate for both routine maintenance and small-batch production where repeatable quality is required. How should the die be mounted and used? Use a compatible die holder or stock sized for round dies of this height (11 mm) and apply suitable cutting fluid; this ensures clean chip formation and prolongs HSS tool life. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a robust combination of HSS‑E cutting material, closed pre‑slotted Form B design and DIN conformity for reliable, repeatable metric threads; order the die directly via Metav Werkzeuge or consult their specialists for application guidance. M10 x 1.5 mm HSS‑E Die, Form B — Closed Pre‑Slotted, Tolerance 6g, TECWERK The M10 x 1.5 mm HSS‑E Die, Form B is a closed, pre‑slotted metric ISO die designed for cutting ISO threads in high‑strength and corrosion‑resistant steels in professional workshops and maintenance settings. HSS‑Co for hard‑to‑machine materials Closed, pre‑slotted Form B design Metric ISO thread, tolerance class 6g Suitable up to 1200 N/mm² tensile strength Reliable threads in demanding materials The closed, pre‑slotted Form B design delivers consistent thread profiles and reduced chip entanglement, which improves productivity when machining tough alloys. Conformity with DIN EN 22568 and metric ISO (DIN 13) thread standards ensures interchangeability and predictable assembly behaviour. With a tolerance class 6g the die produces threads that meet common industrial fit requirements, reducing the need for subsequent rework and ensuring dependable mating with bolts and nuts specified to the same class. Durable cutting performance and longer tool life Manufactured from HSS‑E (cobalt‑alloyed high‑speed steel), this die sustains cutting performance on stainless, heat‑ and acid‑resistant steels as well as special alloys. Cobalt alloying increases red hardness and wear resistance so the tool retains sharpness under elevated temperatures and heavy use. The result is fewer tool changes, lower downtime and a better cost‑benefit ratio for production or repair tasks while preserving surface quality and dimensional accuracy. Practical workshop compatibility and handling benefits A nominal height of 11 mm and the die’s closed construction provide mechanical stability during threading, helping to keep concentricity and run‑out low. The pre‑slotted feature assists chip evacuation compared with fully closed dies, balancing strength with practical chip control. This combination makes the tool suitable for a varied workshop environment where components range from corrosion‑resistant fasteners to higher‑strength steels up to 1200 N/mm². For specification checks or application matching, Metav’s technical advisers are available to recommend the correct thread standard and tolerance for specific assembly requirements. For reliable supply and application support, order the TECWERK M10 x 1.5 mm HSS‑E die via Metav Werkzeuge or contact Metav’s specialists at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice Technical data Article number: 2000867845NW Description: Die, Form B, M10 x 1.5 mm, HSS‑E, 6g, TECWERK Manufacturer: TECWERK UID: 2000867845NW Facts Thread: M10 x 1.5 mm Tolerance: 6g Height: 11 mm Max tensile strength: up to 1200 N/mm² Special features Cutting material: HSS‑E (HSS‑Co) Standard: DIN EN 22568 Design: closed, pre‑slotted die (Form B) Application: stainless, heat‑ and acid‑resistant steels; special alloys; hard‑to‑machine materials Thread standard: metric ISO thread (DIN 13) Type: VA FAQ Which materials can be machined with this die? The TECWERK M10 x 1.5 mm HSS‑E die is suitable for stainless, heat‑ and acid‑resistant steels, special alloys and other hard‑to‑machine materials up to around 1200 N/mm² tensile strength. What does HSS‑E mean and why is it relevant? HSS‑E denotes cobalt‑alloyed high‑speed steel; the cobalt increases red hardness and wear resistance so the die maintains cutting performance at higher temperatures and under heavy loads. Is the thread compatible with standard metric fasteners? Yes — the die cuts metric ISO threads in accordance with DIN 13 and produces a 6g tolerance, ensuring compatibility with standard fasteners specified to the same norms. How does the closed pre‑slotted Form B design affect performance? The closed Form B offers robust guidance for accurate thread form while the pre‑slotted geometry aids chip evacuation, reducing the risk of congestion and improving surface finish compared with fully closed dies. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from precise left‑hand metric threads, robust HSS construction and a closed, pre‑slotted Form B design for reliable chip control and consistent fit; order this threading die directly via Metav Werkzeuge or consult our advisors for application guidance. TECWERK left‑hand threading die M10×1.5, Form B, HSS (6g) The TECWERK left‑hand threading die M10×1.5 Form B is a high‑precision metric ISO die designed for producing left‑hand threads in steels up to approximately 800 N/mm². High-speed steel (HSS) construction Left-hand cutting for reverse threads Metric ISO thread M10×1.5, tolerance 6g Closed, pre-slotted Form B design Accurate threads that save rework The combination of DIN EN 22568 compliance, a M10×1.5 profile and tolerance 6g ensures reproducible engagement and consistent interchangeability with mating parts. This consistency reduces assembly adjustments and rejects, providing a measurable improvement in process reliability. By choosing a tool specified to a recognised standard, the likelihood of downstream fitting or sealing issues is minimised, which supports stable production planning and fewer corrective operations. Robust material and extended service life Manufactured from high‑speed steel (HSS), this threading tool is engineered for durability under demanding cutting loads. HSS retains hardness at elevated temperatures and resists wear better than standard carbon steels, so the tool maintains a cutting edge through repetitive thread forming in medium‑strength steels. The die is suitable for use on steels with a tensile strength of up to 800 N/mm², which covers a broad range of common workshop alloys and reduces the frequency of tool replacement, contributing to lower lifetime operating costs. Secure chip control and handling benefits The Form B closed, pre‑slotted design offers improved stability during threading and promotes controlled chip evacuation, which helps maintain thread quality and protects the cutting edges. The left‑hand cutting orientation makes the tool ideal for applications that require reverse threads or where mating components are designed with counter‑rotational engagement. The compact height of 11 mm and standard metric profile allow integration into conventional die stocks or holders, offering straightforward handling and quick changeover in production or maintenance tasks. For supply and application advice on the TECWERK left‑hand threading die M10×1.5 (SKU 2000867446NW), contact Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com — for prompt, expert support and reliable delivery. Technical data Article number: 2000867446NW Product name: TECWERK left‑hand threading die M10×1.5 Form B HSS 6g Manufacturer: TECWERK Core specifications Thread: M10×1.5 Tolerance: 6g Form: B Height: 11 mm Standard: DIN EN 22568 Suitable material strength: up to approx. 800 N/mm² Special features Material: HSS (high‑speed steel) Left‑hand cutting Metric ISO thread (DIN 13) Closed, pre‑slotted design Cutting material: HSS FAQ Is this die suitable for cutting left‑hand threads? Yes. The TECWERK left‑hand threading die M10×1.5 (SKU 2000867446NW) is specifically designed for left‑hand thread cutting and produces metric ISO left‑hand threads. What materials can be machined with this die? The die is made of HSS and specified for use in steels up to approximately 800 N/mm² tensile strength, as indicated for the TECWERK M10×1.5 Form B tool. Which standards and tolerances apply to this tooling? This threading tool complies with DIN EN 22568 and produces a metric ISO thread to DIN 13 with a tolerance field of 6g, ensuring standardised fit and interchangeability. What does the Form B closed, pre‑slotted design mean in practice? The Form B closed, pre‑slotted geometry on the TECWERK die enhances stability during cutting and supports controlled chip evacuation, which helps to maintain thread quality and tool life. Why choose an HSS die over a carbon steel alternative? An HSS die, such as this TECWERK M10×1.5, offers superior hardness at higher cutting temperatures and better wear resistance, resulting in longer service life and more consistent thread quality under repeated use. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of proven HSS cutting geometry and a 6g tolerance for reliable metric threads; combine durability, standard conformity and stable chip control to keep assembly runs consistent. Order the tooling directly via Metav Werkzeuge or consult the team for application-specific advice. Threading die "Form B" M12 x 1.75 mm, HSS, 6g — TECWERK Threading die "Form B" M12 x 1.75 mm, HSS, 6g — TECWERK is a metric ISO external die for cutting M12 × 1.75 mm threads in general engineering applications, designed to meet DIN standards and to perform reliably in steelworking environments High-speed steel (HSS) for long tool life Metric ISO thread to DIN 13 standard Tolerance field 6g for precise fits Suitable for steels up to 800 N/mm² Closed, pre-slit Form B for stable cutting Accurate metric threads with proven tool steel Made from HSS and specified to the DIN EN 22568 series, this round die is engineered to produce M12 x 1.75 mm threads with a 6g tolerance field. The combination of high-speed steel and standardised geometry ensures consistent tooth form and surface finish, reducing the need for post-process correction. For production and maintenance tasks where repeatable dimensional accuracy matters, the robust material and standard compliance translate into fewer rejects and predictable assembly behaviour. Stable cutting performance for steel applications The Form B configuration, supplied as a closed, pre-slit die, provides better axial guidance and reduced vibration during threading operations. This makes it particularly suitable for machining tasks involving steels up to 800 N/mm², where stable cutting conditions preserve flank integrity and extend tool life. The pre-slit design also assists chip evacuation and helps avoid tool seizing on interrupted cuts, delivering measurable improvements in process reliability. Efficiency and consistent results on the shop floor By combining standard metric form with durable cutting material, the die contributes to higher throughput and lower rework rates. The tooling’s geometry supports consistent threads and uniform assembly fits, which simplifies quality control and speeds up downstream processes. For workshops and production lines aiming for efficient changeover and minimal stoppage, this die offers a balance of durability and dimensional fidelity that supports leaner operations. Practical guidance for selection and care The tolerance field 6g indicates a commonly accepted external thread fit for general engineering use; it provides reproducible thread engagement without demanding specialised mating parts. Use suitable cutting fluid and moderate cutting speeds for optimal surface quality and tool life, and ensure correct clamping in a compatible holder for round dies. If there is uncertainty about application limits or material compatibility, Metav Werkzeuge’s technical advisors can provide tailored recommendations to match specific requirements. For reliable metric threading with TECWERK quality, contact Metav Werkzeuge for procurement and application support at info@metav-werkzeuge.com or call +49 2822 7131930 — assistance from the Emmerich quality centre is available for selection and technical queries Technical Data SKU: 2000867742NW Label: Threading die Form B M12 x 1.75 mm HSS 6g TECWERK Manufacturer: TECWERK UID: 2000867742NW Specifications Thread: M12 x 1.75 mm (metric ISO to DIN 13) Tolerance field: 6g Height: 14 mm Material: HSS (high-speed steel) Suitable for steels up to ≈800 N/mm² Features DIN EN 22568 compliance Form: B (closed, pre-slit design) Schneidstoff: HSS Packaging unit: 1 FAQ What thread size does this die cut? The TECWERK threading die cuts an external metric thread of M12 x 1.75 mm (SKU 2000867742NW). Which materials is the die suitable for? The die, made of HSS, is specified for use on steels up to around 800 N/mm² and is suitable for typical engineering steelwork. What does the tolerance 6g mean for assemblies? Tolerance field 6g provides a standard external thread fit appropriate for general engineering applications, giving reproducible engagement without specialised mates. Is the die compatible with common holders? The closed, pre-slit Form B design is compatible with standard round-die holders; correct clamping ensures axial guidance and stable cutting. Which standards does the tool conform to? The tool references DIN EN 22568 and produces metric ISO threads per DIN 13, supporting conformity in industrial applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combining HSS‑E wear resistance with a closed, pre-slotted Form B design, this TECWERK M12×1.75 threading die provides reliable, repeatable threads in hard-to-machine alloys and stainless steels; order directly via Metav Werkzeuge or request application advice from our consultants. TECWERK Threading die, Form B – M12×1.75 mm, HSS‑E, tolerance 6g TECWERK Threading die Form B M12×1.75 mm HSS‑E 6g is a metric ISO die for cutting external threads in demanding materials and industrial environments HSS‑E (cobalt) cutting material Metric ISO thread M12×1.75, tolerance 6g Closed pre-slotted Form B design Suitable for stainless and alloyed steels Durable cutting performance for demanding alloys The die is manufactured from HSS‑E (cobalt-alloyed high-speed steel), offering increased hardness and thermal stability for extended tool life when machining tough materials. Designed to handle materials up to 1200 N/mm² tensile strength, the tool resists wear and preserves cutting geometry under elevated loads. Conformity to DIN EN 22568 ensures material and production standards that support predictable life cycles in serial production. For workshops and production lines where downtime costs are high, the choice of a cobalt-enriched high-speed steel provides measurable gains in tool longevity and consistent thread quality. Precision threads that meet ISO and DIN standards The die cuts a metric ISO thread M12×1.75 to DIN 13 with a 6g tolerance field, delivering threads that mate reliably with standard fasteners and components. The specified tolerance translates into predictable clearances for assembly and torque behaviour, reducing rework and component rejection. By using a tool produced for these standards, engineers and buyers obtain interchangeability across suppliers and assemblies, simplifying inventory and quality assurance processes. The adherence to recognised tolerances supports traceable production results and facilitates integration into established quality systems. A design focused on stability and consistent cycle times Constructed in Form B with a closed, pre-slotted layout and a height of 14 mm, the die provides guided engagement and uniform chip evacuation for external threading. The closed form produces full-profile threads with superior concentricity compared with open dies, while the slots assist chip breaking and reduce the risk of jamming when cutting long or gummy materials. The compact height and robust geometry make the tool suitable for use in die stocks and powered holders, enabling stable cutting at consistent feed and speed and lowering the likelihood of chatter or premature tool wear. Built for professional workshops and industrial use Engineered for demanding applications, this threading die is intended for industrial toolrooms, maintenance shops and production environments where hard-to-machine, heat- and acid-resistant steels, special alloys and conventional steels are encountered. The robust material choice and standard-compliant geometry reduce process variability and support reproducible assembly outcomes. Backed by the distribution and quality-filtering capabilities of Metav Werkzeuge, the die represents a practical option for operations seeking to standardise their external threading tools and improve reliability across batches. For secure, industrial-grade threading in demanding materials, contact Metav Werkzeuge to order the TECWERK threading die or to discuss technical suitability: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 2000867846NW Product name: Threading die Form B M12×1.75 mm HSS‑E 6g TECWERK Manufacturer: TECWERK Core data Thread: M12×1.75 (metric ISO) Tolerance: 6g Height: 14 mm Strength capacity: up to 1200 N/mm² Standard: DIN EN 22568 Special features Cutting material: HSS‑E (cobalt) Form: B, closed, pre-slotted Type: VA Application: for hard-to-machine materials, stainless, heat- and acid-resistant steels, special alloys Packaging unit: 1 FAQ Which materials can be machined with this die? The TECWERK threading die is suitable for stainless, heat- and acid-resistant steels, special alloys and steels up to around 1200 N/mm² tensile strength as specified by the tool data. What thread form and tolerance does the tool produce? The die cuts a metric ISO thread M12×1.75 to DIN 13 with a 6g tolerance, providing standardised external threads compatible with ISO-class fasteners. What advantage does the closed, pre-slotted Form B offer? The closed Form B delivers full-profile threads with improved concentricity, while the pre-slotted design assists chip control and reduces jamming during continuous or manual threading operations. Is the cutting material suitable for high-temperature or abrasive conditions? The HSS‑E composition with cobalt enhances hot hardness and wear resistance, making the die more durable under elevated temperatures and when machining abrasive, hard-to-cut alloys. How is the die supplied for workshop use? The tool is supplied in a single unit packaging and is designed for use in standard die stocks and powered holders; nominal data and standard compliance are provided to aid integration in production settings. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of robust HSS construction, precise M12×1.75 ISO threading and a left‑hand cutting configuration to maintain production quality and reduce rework; order the TECWERK thread die directly via Metav Werkzeuge or ask our consultants for application guidance. Thread die Form B M12×1.75 HSS, left‑hand cut – TECWERK A compact thread die Form B M12×1.75 designed for cutting ISO metric threads in medium‑strength steels, featuring a closed, pre‑slotted construction and left‑hand cutting for reverse‑thread applications. HSS solid high‑speed steel construction Form B closed, pre‑slotted design Left‑hand cutting for reverse threads For steels up to 800 N/mm² tensile strength Precision and durability for repetitive threading tasks The solid HSS composition delivers consistent edge retention and heat resistance, giving reliable life under repeated use. Thanks to the die's Form B geometry and closed construction, thread profiles are formed with minimal risk of distortion, which improves first‑pass yield. This results in fewer rejects and less downtime on the shopfloor, so production runs remain steady and predictable. Application range and clarity on tolerances Designed to cut an ISO metric thread to DIN 13, the tool produces an M12×1.75 profile with a 6g tolerance, suitable for general assembly work and repair operations in workshop environments. The tolerance class 6g indicates a general‑purpose external thread with modest clearance to mating nuts or tapped holes, easing assembly for fastened joints. Compatibility with steels up to approximately 800 N/mm² tensile strength makes the die well suited to common structural and engineering steels. Practical features that support efficient workflows The pre‑slotted design simplifies chip evacuation and assists in maintaining thread quality over multiple cuts, while the left‑hand cutting orientation is ideal where reverse threads are required or where component rotation demands a counter‑directional form. The modest 14 mm height offers a compact footprint for hand tooling or machine holders, and the closed die shape protects the cutting edges during handling, reducing the frequency of re‑grinding and maintenance interruptions. For reliable left‑hand threading and assured supply, contact Metav Werkzeuge to request the TECWERK thread die M12×1.75 and receive tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867447NW Label: Schneideisen Form B M12x1,75mm HSS 6g li.TECWERK Manufacturer: TECWERK Key dimensions and performance Thread: M12×1.75 Tolerance class: 6g Height: 14 mm Suitable for steels up to ≈800 N/mm² tensile strength Materials & special features Material: HSS Form: B Left‑hand cutting Closed, pre‑slotted construction ISO metric thread to DIN 13 Packaging unit: 1 FAQ What materials can be machined with this die? The TECWERK thread die is intended for steels up to approximately 800 N/mm² tensile strength and is made from HSS to withstand typical workshop conditions. How does the left‑hand cutting orientation affect use? Left‑hand cutting produces reverse threads; the die's left‑hand configuration suits components that require counterclockwise thread direction or assemblies where the mating part rotates the opposite way. What does Form B and the closed, pre‑slotted design mean in practice? Form B denotes a closed die profile; the closed, pre‑slotted construction improves chip control and protects cutting edges, giving more consistent thread form and longer tool life. How tight is the thread produced with tolerance 6g? The 6g tolerance is a general‑purpose external thread class that offers reliable fit with standard nuts and tapped holes while allowing straightforward assembly in typical engineering applications. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS cutting material, metric ISO thread accuracy and a compact 18 mm height for consistent external threads; order the die directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Threading Die Form B — M16×2 mm, HSS, 6g TECWERK Threading Die Form B M16×2 mm is a solid, pre-slotted external threading die designed for metric ISO threads and industrial workshop use. HSS material for robust cutting M16×2 mm metric ISO thread specification Tolerance field 6g for precise fits Suitable for steels up to 800 N/mm² Precise metric threads that reduce rework The TECWERK Threading Die Form B M16×2 mm produces reliable metric ISO threads to DIN 13 with tolerance class 6g, ensuring a consistent fit for matched fasteners. The controlled geometry and standard conformity minimise the need for subsequent grinding or fitting, which reduces cycle times and scrap rates. This predictable accuracy benefits production planning by lowering rejects and easing assembly operations. Durable high-speed steel for demanding materials Made from HSS, the tool offers a balanced combination of hardness and toughness that maintains cutting edges under repeated use. The die is rated for work on steels with tensile strengths up to 800 N/mm², providing a dependable option for both mild and higher-strength steel components. Using a high-quality cutting material increases the tool life and reduces frequency of replacement, supporting uninterrupted workshop throughput. Closed, pre-slotted design for consistent thread profiles The closed, pre-slotted form (Form B) with an overall height of 18 mm ensures axial stability during the cutting process and consistent thread geometry. The pre-slotted construction helps with chip control and eases starting, especially on solid rods or bars. For machinists and maintenance teams, this design translates to fewer alignment issues and a more predictable machining outcome when producing external threads. Integration into workshop workflows and inventory Supplied to recognised standards such as DIN EN 22568, this threading die fits established tooling systems and standard sizes, simplifying spare-part management. Its specification as M16×2 mm with 6g tolerance makes it suitable for common assemblies and replacement tasks across industrial and maintenance settings. Clear technical conformity supports procurement decisions and reduces the administrative burden of custom parts. For tailored technical advice or to request prompt delivery from our Emmerich warehouse, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will assist with selection and availability Technical Data Article number: 2000867746NW Product: Threading die, Form B, M16×2 mm Manufacturer: TECWERK Facts Height: 18 mm Thread: M16×2 mm Tolerance: 6g Suitable for steels up to 800 N/mm² Special features Material: HSS Standard: DIN EN 22568 Closed, pre-slotted form (Form B) FAQ What thread standard does this die produce? The die produces metric ISO threads compliant with DIN 13 and DIN EN 22568, delivering standardised external threads for general industrial use. Which materials can be machined with this die? This HSS die is suitable for machining steels with tensile strength up to approximately 800 N/mm²; it is intended for standard workshop steels and similar ferrous materials. How does the pre-slotted design affect performance? The closed, pre-slotted design improves chip control and starting behaviour, helping to maintain consistent thread form and reducing the likelihood of binding or misalignment during threading. Is the tolerance suitable for assembly with standard bolts? Yes, the 6g tolerance field provides a commonly used external thread tolerance that fits well with corresponding internal threads in standard assemblies. What is the product identifier for ordering or reference? Reference the SKU 2000867746NW when specifying the TECWERK threading die M16×2 mm for procurement or replacement purposes. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combine high-performance HSS-E cutting with a closed, pre-slit Form B design for reliable metric threads in demanding materials. Order the Threading die Form B M16x2 HSS-E 6g TECWERK directly via Metav Werkzeuge or ask our consultants if needed. Threading die Form B M16x2 HSS-E 6g by TECWERK A precision threading die for external metric ISO threads, designed for machining hard-to-cut and heat- or acid-resistant steels in professional workshop and industrial settings. HSS-E for hard materials Metric ISO thread to DIN 13 Tolerance field 6g Closed, pre-slit Form B Suitable up to 1200 N/mm² strength Precision and material performance for consistent external threads The HSS-E cutting material combines high-speed steel with a cobalt alloy to deliver improved hot hardness and wear resistance compared with standard HSS. This composition ensures sustained cutting performance when forming M16x2 threads in tougher substrates. The resulting benefit is a longer tool life and fewer tool changes, which supports continuous production and reduces downtime. Where repeatable thread quality is essential, the material choice directly improves stability and surface finish. Accurate threads to specification for assembly reliability Compliance with DIN 13 and the 6g tolerance provides a clear, measurable basis for interchangeability in assemblies. The Form B geometry — a closed die with pre-slitting — produces a clean external thread profile and maintains alignment during cutting. For operations that demand reliable mating with nuts and tapped holes, this threading solution reduces the need for post-processing and minimises assembly rejects. The specification-driven design allows planners to predict fit and function with confidence. Designed for demanding workpieces and straightforward handling Engineered for machining stainless, heat- and acid-resistant steels, special alloys and steels up to 1200 N/mm² tensile strength, this die suits repair, maintenance and production tasks where standard tooling falls short. The compact 18 mm height provides a robust cutting head while remaining compatible with common die stocks and holders for external threading. Clear labelling and standard dimensions support easy integration into existing tooling sets and workflows. Dependable supply and technical backing from a precision partner Selecting this TECWERK threading die delivers a balance of performance and robustness for heavy-duty applications. Metav’s position as a precision partner adds further value: central stock in Emmerich, a broad product range and an experienced advisory service support efficient procurement and implementation. For complex requirements, documented specifications such as M16x2, HSS-E and the 6g tolerance help avoid costly mismatches and ensure the right tool is chosen first time. For reliable external threading in high-strength and corrosion-resistant materials, order the TECWERK M16x2 threading die via Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com or +49 2822 7131930 for tailored technical advice Technical Data Article number: 2000867848NW Designation: Threading die Form B M16x2 HSS-E 6g TECWERK Material: HSS-E Form: B Thread standard: Metric ISO DIN 13 Facts Tolerance field: 6g Height: 18 mm Suitable for steels up to 1200 N/mm² Packaging unit: 1 Special features Closed, pre-slit Form B For hard-to-machine materials Suitable for heat- and acid-resistant steels For special alloys and high-strength steel FAQ What materials can this die machine effectively? The threading die Form B M16x2 HSS-E 6g TECWERK is suitable for heat‑ and acid‑resistant steels, special alloys and steels up to 1200 N/mm² tensile strength. Does the die comply with a recognised thread standard? Yes, the die produces metric ISO threads in accordance with DIN 13 and is manufactured to the 6g tolerance field. Can the die be used with standard die stocks? The die’s Form B geometry and standard dimensions allow use with common die stocks designed for round dies. What advantage does HSS‑E provide over standard HSS? HSS‑E (cobalt alloy) offers higher hot hardness and improved wear resistance, which extends tool life when cutting tougher or hotter-running materials. Is this die suitable for production or repair work? Its closed, pre‑slit design and robust HSS‑E construction make the die appropriate for both production and maintenance applications where consistent external threads are required. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a robust combination of high-speed steel construction, DIN-compliant geometry and a precise 6g tolerance for dependable left-hand thread cutting; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Round Die M16 x 2 mm, HSS, Left-hand (Form B) The TECWERK round die M16×2 mm HSS 6g left-hand is a Form B external-threading tool designed for metric ISO threads, suitable for workshop and industrial use where reverse threads are required. *HSS for durable cutting performance *DIN EN 22568 compliant geometry *Left-hand cutting for reverse threads *Tolerance 6g for ISO metric precision Reliable results for reverse-thread applications The die is produced from HSS, offering a good balance of toughness and wear resistance for repetitive external-thread cutting. Its M16×2 mm nominal pitch and 6g tolerance deliver predictable fitting behaviour with ISO-standard nuts and components, reducing rework and assembly time. Where reverse threads are specified, the left-hand cutting orientation ensures the correct helix direction without retooling. Closed Form B design improves thread quality Built to Form B with a closed, pre-slotted profile, the tool maintains concentricity while allowing chip control during manual or machine-driven threading. The pre-slotted construction eases chip evacuation compared with fully solid dies, and the Form B section supports consistent flank geometry, which translates into clean thread forms and fewer rejects in serial production. Engineered for common steel applications Specified for use on steels up to approximately 800 N/mm² tensile strength, the die is suited to a wide range of engineering steels encountered in maintenance and fabrication. The high-speed steel composition tolerates intermittent high cutting forces and retains cutting edge integrity, making the tool a sound choice for repair work and smaller batch production where cost-effective durability matters. Standards, handling and integration Conforming to DIN EN 22568 and compatible with metric ISO thread standards (DIN 13), the tool integrates easily into existing tooling sets. The compact height 18 mm allows use in standard die stocks and holders. For longevity, maintain sharp cutting edges, keep the tool clean of chips and lubricate appropriately during use to preserve thread accuracy and surface finish. For technical guidance or fast delivery from Emmerich, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 to order the TECWERK HSS round die (SKU 2000867449NW) and discuss suitable die stocks and lubricants Technical data Article number: 2000867449NW Item: Schneideisen Form B M16x2mm HSS 6g li.TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867449NW Facts Thread: M16 × 2 mm Tolerance: 6g Height: 18 mm Suitable for steels up to approx. 800 N/mm² Standard: DIN EN 22568 Special features Cutting material: HSS Left-hand cutting orientation Form B geometry Closed, pre-slotted form Metric ISO thread (DIN 13) FAQ What materials can this die machine external threads in? The TECWERK round die is designed for use on steels up to about 800 N/mm² tensile strength and performs well on common engineering steels within that range. Is the die suitable for hand-held die stock use? Yes, the Form B design and 18 mm height make the die compatible with standard die stocks for manual threading tasks. What does the 6g tolerance mean in practice? Tolerance 6g specifies the external thread tolerance class for metric ISO threads, ensuring the produced male thread mates reliably with standard female components. Can this tool produce left-hand threads on shafts and studs? The left-hand cutting configuration is intended specifically for producing reverse or left-hand external threads without altering machining direction. Which standards does the tool comply with? The die is manufactured to DIN EN 22568 and corresponds to metric ISO thread specifications under DIN 13. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund