Take advantage of a durable HSS‑Co construction combined with a cross‑serrated cutting geometry and a secure cylindrical shank for reliable slot milling in demanding workshop and production settings; order the cutter directly via Metav Werkzeuge or consult the specialists for application advice. T‑slot cutter DIN 851 AB Type N, 12.5 mm – HSS‑Co, cross‑serrated (MAYKESTAG) The T‑slot cutter DIN 851 AB Type N is a right‑hand cutting tool designed for milling T‑slots and grooves in structural, case‑hardened and quenched‑and‑tempered steels as well as for short‑chipping non‑ferrous metals in general workshop and industrial applications HSS‑Co construction for heat resistance Cross‑serrated cutting for reliable chip breaking Nominal diameter 12.5 mm for standard T‑slots Cylindrical shank with drive flat for secure clamping Durable alloy and cutting geometry for consistent results Manufactured from cobalt high‑speed steel (HSS‑Co), this cutter delivers elevated red‑hardness and wear resistance under continuous milling loads, which supports longer service intervals and stable cutting performance. The cross‑serrated tooth form promotes effective chip breaking with short‑chipping materials and improves the surface appearance of the groove. Conformity with DIN 851 AB indicates the tool follows recognised industrial standards, helping to ensure reproducible results across batches and machines. Precise mounting and controlled chip flow for efficient machining The tool’s nominal diameter 12.5 mm and shank diameter 10 mm are matched to common spindle and collet systems, while the cylindrical shank with drive flat enables positive torque transmission and minimises slippage during heavy cuts. With 6 teeth (Z6) and tooling geometry optimised for T‑slot profiles (slot width per DIN 650: 6 mm), the cutter balances feed rate and surface finish to reduce rework. The right‑hand cutting orientation suits conventional milling directions and typical machine setups, supporting consistent cycle times. Practical benefits for workshop and production use Specification and material choices concentrate on application reliability: the HSS‑Co substrate gives resistance against thermal softening, the serrated edges maintain chip form even in mixed batches of non‑ferrous components, and the standardised dimensions simplify tool management and replacement. For tasks that demand robust groove geometry and repeatable surface quality in steel grades and short‑chipping NE‑metals, this cutter delivers a pragmatic mix of longevity and predictable cutting behaviour that supports continuous operation and reduces downtime. Contact Metav Werkzeuge for tailored technical advice, application recommendations and to arrange procurement by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4117802035NW Product: T‑slot cutter DIN 851 AB Type N, 12.5 mm, HSS‑Co Brand: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 Facts Nominal diameter d1: 12.5 mm Shank diameter d2: 10 mm Teeth: 6 Slot width (DIN 650): 6 mm Cutting direction: right‑hand Standard: DIN 851 AB Special features Material: cobalt high‑speed steel (HSS‑Co) Cutting geometry: cross‑serrated Shank type: cylindrical shank with drive flat Application: structural, case‑hardened and quenched‑and‑tempered steels; short‑chipping non‑ferrous metals FAQ What materials can be machined with this T‑slot cutter? The T‑slot cutter is suitable for milling structural steels, case‑hardened and quenched‑and‑tempered steels, and for short‑chipping non‑ferrous metals as indicated in the product specification. Which standards apply to the tool and the slots it produces? The cutter conforms to DIN 851 AB and is intended for slot profiles matching DIN 650 (slot width 6 mm), ensuring compatibility with standardised T‑slot geometries. What are the key mounting dimensions to consider? Key dimensions are nominal diameter 12.5 mm, shank diameter 10 mm with a drive flat, and 6 teeth (Z6); these define clamping requirements and expected slot geometry. Is the cutter designed for right‑ or left‑hand milling? The tool is specified as right‑hand cutting, suitable for conventional milling directions in most milling setups. How does the cross‑serrated geometry affect performance? Cross‑serration promotes chip breaking and helps maintain a short, manageable chip form, which benefits surface finish and reduces the risk of built‑up edge during the machining of short‑chipping materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of durable HSS‑Co construction, a cross‑tooth geometry and precise 18 mm nominal diameter for consistent T‑slot machining; order the T‑slot cutter directly via Metav Werkzeuge or ask the Metav consultants for specification support. T‑slot cutter DIN 851 AB – 18 mm HSS‑Co, cross‑tooth – MAYKESTAG The T‑slot cutter DIN 851 AB is a Type N cutter designed for machining T‑slots in construction, quenched and tempered steels and short‑chipping non‑ferrous metals with a cylindrical shank and driving flat. HSS‑Co for elevated heat resistance Cross‑tooth geometry for clean chips Complies with DIN 851 AB Type N Cylindrical shank 12 mm with driving flat High‑performance cutting that reduces cycle times The T‑slot cutter DIN 851 AB combines a HSS‑Co substrate with a cross‑tooth cutting geometry to deliver reliable material removal in short‑chipping alloys and common construction steels. The cobalt‑alloyed high‑speed steel sustains higher cutting temperatures and preserves edge integrity during interrupted cuts, reducing tool change frequency and contributing to improved machine uptime. The tool’s right‑hand cutting action and eight cutting edges ensure steady engagement and predictable cutting forces for repetitive slotting tasks. Predictable slot geometry and material flexibility Designed to produce T‑slots to recognised standards, the cutter’s nominal diameter 18 mm and specified compatibility for T‑slots to DIN 650 (10 mm) support repeatable slot profiles with minimal secondary machining. The combination of Type N geometry and the cross‑tooth design promotes short, controllable chips when used on short‑chipping non‑ferrous metals and many steels, while still being suitable for quenched and tempered grades. Short‑chipping means the material breaks into small fragments during cutting, which lowers the risk of clogging and simplifies chip evacuation. Easy integration into workshop toolsets and reliable supply The cylindrical shank with a 12 mm diameter and driving flat allows secure clamping in standard toolholders and collets, enabling straightforward replacement and minimal setup time. Supplied as a single unit, the cutter fits typical workshop workflows and is part of a comprehensively vetted offering available through Metav Werkzeuge, whose warehouse in Emmerich acts as a quality filter for European supply chains. Specifying tools with standardised dimensions and recognised standards reduces procurement complexity and supports consistent production quality. For procurement assistance, specification clarification or to secure this MAYKESTAG T‑slot cutter quickly from Metav Werkzeuge, contact our Metav consultants in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4117802037NW Manufacturer: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 Key dimensions Nominal diameter d1: 18 mm Shank diameter d2: 12 mm For T‑slots to DIN 650: 10 mm Teeth: Z 8 Features & applications Material: HSS‑Co Standard: DIN 851 AB, Type N Cross‑tooth cutting geometry Right‑hand cutting Cylindrical shank with driving flat Suited for construction, quenched and tempered steels and short‑chipping non‑ferrous metals FAQ Which materials can this cutter machine effectively? The T‑slot cutter DIN 851 AB from MAYKESTAG is specified for machining construction steels, quenched and tempered steels and short‑chipping non‑ferrous metals, reflecting the intended applications listed for SKU 4117802037NW. Is the cutter compliant with DIN standards for T‑slot production? Yes, the tool is manufactured to DIN 851 AB and referenced for T‑slot dimensions to DIN 650, ensuring compatibility with standard slot geometries. What do the number of teeth and the cross‑tooth design mean in practice? With Z 8 and a cross‑tooth geometry, the cutter produces short, manageable chips and maintains a balanced cutting action, which helps reduce vibration and promotes a smoother slot surface with the MAYKESTAG tool. What shank size is required and how is the tool clamped? The cutter has a 12 mm cylindrical shank with a driving flat for secure clamping in standard collets or holders; this dimension supports straightforward integration into common workshop toolholders. Can the cutter handle interrupted cuts and tougher steels? The cobalt‑alloyed HSS‑Co construction increases red hardness and wear resistance, making the cutter suitable for interrupted cuts and for many quenched and tempered steels within the tool’s intended application range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust HSS‑Co design and a cross‑helix tooth geometry to achieve consistent, short‑chip formation and reliable T‑slot profiles; order the cutter directly via Metav Werkzeuge or consult our technical team for application advice. MAYKESTAG T‑slot cutter DIN 851 AB Type N — 21 mm HSS‑Co, cross‑helix teeth The MAYKESTAG T‑slot cutter DIN 851 AB Type N is a right‑hand cutting tool engineered for machining T‑slots in structural and quenched‑and‑tempered steels and for short‑chipping non‑ferrous materials HSS‑Co construction for extended service life Cross‑helix tooth geometry for controlled chip breaking Conforms to DIN 851 AB, Type N Cylinder shank with drive flat for secure clamping Accurate T‑slot profiles with proven standard compliance The cutter delivers repeatable slot geometry thanks to its conformity with DIN 851 AB, ensuring compatibility with established workshop processes and fixtures. Manufactured in HSS‑Co, the tool material combines hardness with toughness for a balance between wear resistance and resistance to chipping. The 21 mm nominal diameter and the tooth form produce consistent slot walls and bottoms, which reduces the need for secondary finishing and supports predictable assembly tolerances on jigs and machine parts. Faster throughput and longer tool life from optimised geometry The cross‑helix tooth arrangement creates short, controllable chips that evacuate efficiently, reducing machine downtime for chip clearing and minimising heat build‑up at the cutting edge. With Z = 8 teeth and a right‑hand cut, the cutter is designed for stable engagement and steady material removal rates in typical T‑slot operations. For production environments where cycle time and tool longevity are priorities, this geometry translates into improved productivity and lower tool‑change frequency. Simple mounting and reliable drive for workshop use A 12 mm shank with a dedicated drive flat provides positive engagement in collets and toolholders, preventing slippage during high feed operations. The cylindrical shank form is compatible with standard toolholding systems, enabling fast tool changes and straightforward integration into existing setups. The tool’s mechanical interface supports consistent concentricity and runout values, which contributes to uniform slot quality across batches. Appropriate applications and material recommendations This cutter is intended for machining structural steels, engineering steels and quenched‑and‑tempered steels, as well as for short‑chipping non‑ferrous metals, where chip control is essential. It is especially suitable where DIN‑compliant T‑slots are required and where right‑hand cutting orientation fits the machine programme. The combination of HSS‑Co material and cross‑tooth geometry makes the cutter a fitting choice for workshops seeking a resilient tool for mixed production runs and occasional heavy engagement. Rely on Metav Werkzeuge to supply the MAYKESTAG T‑slot cutter — request tailored technical guidance or arrange purchase via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4117802038NW Product label: T‑slot cutter DIN 851 AB Type N, 21 mm, HSS‑Co Manufacturer: ALPEN-MAYKESTAG GmbH Packaging unit: 1 Facts Nominal diameter d1: 21 mm Shank diameter d2: 12 mm Slot width per DIN 650: 12 mm Number of teeth: 8 Special features HSS‑Co material Cross‑helix / cross tooth geometry DIN 851 AB, Type N Right‑hand cut Cylinder shank with drive flat For structural, engineering and quenched‑and‑tempered steels For short‑chipping non‑ferrous metals FAQ What materials is the cutter suitable for? The MAYKESTAG T‑slot cutter is designed for structural and engineering steels, quenched‑and‑tempered steels and short‑chipping non‑ferrous metals. Which standard does the tool comply with? The cutter is manufactured to DIN 851 AB, Type N, ensuring compatibility with DIN‑specified T‑slot dimensions. What are the critical dimensions for mounting the cutter? Key mounting dimensions are the 21 mm nominal diameter and the 12 mm shank diameter; the shank includes a drive flat for secure clamping. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of robust HSS‑Co construction, DIN‑compliant geometry and precise chip control for reliable T‑slot milling in production environments; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. T‑slot cutter DIN 851 AB Type N – 25 mm, HSS‑Co, cross‑tooth by MAYKESTAG The T‑slot cutter DIN 851 AB Type N is a right‑hand, high‑performance milling tool designed for producing DIN‑650 T‑slots and medium‑duty slotting in steels and short‑chipping non‑ferrous materials. DIN 851 AB compliant design Cobalt HSS (HSS‑Co) for extended tool life Cross‑tooth geometry for improved chip control Cylindrical shank with drive face for secure clamping For 14 mm DIN 650 T‑slots Durable cutting performance that reduces tool changes The high‑alloy HSS‑Co composition provides a balance of hardness and toughness that keeps cutting edges stable under thermal load. Conformity with DIN 851 AB ensures predictable geometry and repeatable results across batches, which reduces process variation and downtime. With a 25 mm nominal diameter and an 8‑tooth configuration, the cutter delivers consistent material removal rates while maintaining a serviceable edge life, making it a cost‑efficient choice for workshops that value uninterrupted throughput and straightforward maintenance. Cleaner chips and better surface quality through crossed teeth The cross‑tooth geometry breaks chips into shorter segments, lowering the risk of chip entanglement and promoting safer evacuation from the slot. Shorter chips and controlled cutting forces result in improved surface finish and reduced tendency for built‑up edge, especially when machining tough steels or short‑chipping alloys. The right‑hand cutting orientation supports conventional milling setups and predictable tool‑path planning, which simplifies process validation and quality assurance on production machines. Stable clamping and machine compatibility for repeatable slots A cylindrical shank with drive face provides a reliable mechanical interface for collet and chuck systems, reducing slippage and run‑out during slotting operations. The 16 mm shank diameter is compatible with common toolholders while the drive face improves torque transmission for interrupted cuts. Together these features support accurate slot positioning and repeatability, which is particularly important when producing T‑slots to the 14 mm width specified for DIN 650 slots. Broad material range for versatile workshop use The tool is engineered for machining construction steels, case‑hardened and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals, offering a single‑tool solution for mixed production environments. The combination of geometry and HSS‑Co substrate enables efficient cutting of moderate‑hardness materials without resorting to carbide for every task. This versatility reduces inventory complexity while keeping performance high when processing commonly encountered components and assembly parts. For reliable T‑slot machining with the HSS‑Co quality of this MAYKESTAG cutter, contact Metav Werkzeuge for order placement and tailored technical advice by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: 4117802039NW Product designation: T‑slot cutter DIN 851 AB Type N, 25 mm Manufacturer: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 Facts Nominal diameter d1: 25 mm Shank diameter d2: 16 mm Slot width (DIN 650): 14 mm Teeth: 8 Cutting direction: right‑hand Special features Material: HSS‑Co (cobalt high‑speed steel) Geometry: cross‑tooth / Kreuzverzahnung Shank: cylindrical shank with drive face Standard: DIN 851 AB Type N Application: construction, case‑hardened and quenched‑and‑tempered steels, short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The T‑slot cutter DIN 851 AB Type N from MAYKESTAG is specified for construction steels, case‑hardened and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals. What is the nominal diameter and shank size? The tool has a nominal diameter of 25 mm and a shank diameter of 16 mm for secure clamping. Which slot width does the cutter produce? Designed for DIN 650 slots, the cutter suits a slot width of 14 mm when used with the appropriate feed and spindle settings. How many teeth does the cutter have and what is the tooth arrangement? The cutter features 8 teeth with a cross‑tooth geometry that promotes short chips and stable cutting behaviour. Is the cutter suitable for conventional collet holders? Yes; the cylindrical shank with drive face ensures stable torque transmission and compatibility with standard collet and chuck systems when milling T‑slots. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSS-Co construction and cross serration for reliable chip control and longer cutter life; the secure cylindrical shank with drive flat ensures repeatable slot geometry and fast changeover. Order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. MAYKESTAG T-slot cutter DIN 851 AB Type N — 28 mm, HSS-Co, cross serrated (Z8) A MAYKESTAG T-slot cutter DIN 851 AB Type N designed for machining T-slots in construction, alloy and quenched-tempered steels and for short‑chipping non‑ferrous metals HSS‑Co body with high wear resistance Cross serration for efficient chip breaking Nominal diameter 28 mm for precise slot width Cylindrical shank Ø 16 mm with drive flat High-performance cutting for demanding steels and non‑ferrous metals The cutter is manufactured from HSS‑Co, a cobalt‑alloyed high‑speed steel that combines hardness with toughness to resist wear during interrupted cuts. The cross serration (Kreuzverzahnung) produces short, controlled chips, improving surface finish and reducing the risk of built‑up edge when machining both quenched and tempered steels and short‑chipping non‑ferrous materials. This results in higher process stability and predictable tool life, which translates into increased machining productivity and fewer tool changes in production environments. Precise slot dimensions and secure tool holding for repeatable results With a nominal diameter 28 mm and a shank Ø 16 mm, the cutter provides consistent slot geometry for applications conforming to DIN 650 T‑slot dimensions. The cylindrical shank with drive flat ensures positive location in the tool holder and stable torque transmission, reducing run‑out and vibration. These characteristics enable accurate, repeatable grooves in fixtures and machine beds, supporting quality control and minimising rework in serial manufacture. Durable design and flexible application for workshop efficiency Equipped with 8 teeth (Z8) and right‑hand cutting flutes, the tool balances material removal with surface integrity. The combination of tooth count and serration reduces cutting forces and promotes heat dissipation, contributing to longer service intervals. Suitable for a range of materials from construction steels to alloyed and heat‑treated steels and selected non‑ferrous alloys, the cutter supports both maintenance and production tasks. The robust design reduces downtime and supports a cost‑effective workflow without compromising precision. For secure supply and expert application advice on the MAYKESTAG T‑slot cutter, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability. Technical data Article number: 4117802040NW Designation: T‑slot cutter DIN 851 AB Type N, HSS‑Co, cross serrated, Z8 Manufacturer: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 UID: 4117802040NW Facts Nominal diameter (d1): 28 mm Shank diameter (d2): 16 mm For T‑slots per DIN 650: 16 mm Teeth: 8 Cutting direction: right‑hand Special features Material: HSS‑Co (cobalt high‑speed steel) Serration: cross serration for chip control Shank: cylindrical shank with drive flat (positive location) Application: construction, alloy and quenched‑tempered steels; short‑chipping non‑ferrous metals Standard: DIN 851 AB, Type N FAQ What materials can be machined with this T‑slot cutter? The MAYKESTAG T‑slot cutter is designed for construction, alloy and quenched‑tempered steels and is suitable for short‑chipping non‑ferrous metals, as stated in the product specification. Which slot width does this cutter produce for DIN 650 applications? The cutter is intended for T‑slots per DIN 650 with a slot size of 16 mm; its nominal diameter 28 mm and geometry are matched to that application. How is the tool secured in the holder to prevent slippage? The tool features a cylindrical shank with drive flat to ensure positive location and reliable torque transmission in the toolholder. Does the cutter offer improved chip control compared with smooth‑tooth cutters? Yes, the cross serration produces short, broken chips and reduces the tendency for long, stringy chips, improving surface finish and process stability. What tooth count does the cutter have and what is the effect on cutting? The cutter has 8 teeth (Z8); this tooth count balances material removal rate and surface quality while supporting stable cutting in the specified materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining HSS‑Co construction, cross-cut geometry and conformity to DIN 851 AB delivers precise, durable T‑slot machining with reliable chip control; order the cutter directly via Metav Werkzeuge or contact our consultants for technical advice. MAYKESTAG T‑slot milling cutter DIN 851 AB, 32 mm, HSS‑Co, cross‑cut The MAYKESTAG T‑slot milling cutter DIN 851 AB Type N is a right‑hand cutter engineered for machining T‑slots in structural, case‑hardened and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals. HSS‑Co construction for extended tool life Cross‑cut teeth for improved chip control DIN 851 AB Type N for standardised slot profiles 32 mm nominal diameter with 16 mm shank Accurate slot profiles for dependable fixturing The cutter is manufactured to DIN 851 AB, which standardises the tooth form and flank geometry for T‑slot milling. This compliance ensures repeatable results and compatibility with fixtures and T‑nuts that conform to the same standards, reducing setup rework. For applications requiring slots to DIN 650, the tool is suitable for producing an 18 mm groove width, giving a predictable seating surface and consistent part location during assembly or fixture use. Robust cutting performance in steels and non‑ferrous alloys Built from HSS‑Co, the tool combines high red‑hardness with toughness, enabling sustained performance when machining demanding workpiece steels. The cross‑cut tooth geometry breaks chips effectively and reduces load peaks on individual teeth, which improves surface finish and extends tool life. These properties make the cutter well suited for structural, case‑hardened and quenched‑and‑tempered steels, while still delivering controlled chips when working with short‑chipping non‑ferrous metals. Secure clamping and efficient material removal A 16 mm shank with a cylindrical profile and drive flat provides a solid connection to the toolholder and minimises run‑out for accurate slot form. The tool’s 32 mm nominal diameter combined with Z=8 teeth balances material removal rate and surface quality: multiple cutting edges distribute cutting forces and reduce vibration, while the right‑hand cutting direction matches conventional spindle rotation. The cylindrical shank and drive flat simplify setup and support consistent cycle times in production environments. For precision T‑slot machining choose the MAYKESTAG HSS‑Co cutter via Metav Werkzeuge for assured supply and expert application support — contact info@metav-werkzeuge.com or call +49 2822 7131930 for detailed consultation. Technical Data SKU: 4117802041NW Name: T‑slot milling cutter DIN 851 AB Type N, 32 mm Brand: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 Facts Nominal diameter d1: 32 mm Shank diameter d2: 16 mm For grooves to DIN 650: 18 mm Teeth: 8 Special features Material: HSS‑Co Tooth geometry: cross‑cut Cutting direction: right‑hand cutting Shank type: cylindrical with drive flat Standard: DIN 851 AB Application: milling structural, case‑hardened and quenched‑and‑tempered steels; short‑chipping non‑ferrous metals FAQ Which materials can this cutter machine effectively? The MAYKESTAG T‑slot milling cutter is suitable for structural, case‑hardened and quenched‑and‑tempered steels, and it also performs well on short‑chipping non‑ferrous metals, thanks to its HSS‑Co composition and cross‑cut geometry. What slot width does the cutter produce for DIN applications? Designed for T‑slots to DIN 650, the tool produces an 18 mm groove width compatible with standard T‑nuts and fixtures when used according to the relevant machining parameters. What are the clamping requirements for stable machining? A rigid toolholder that accepts a 16 mm cylindrical shank with a drive flat is recommended to ensure low run‑out and secure clamping; this supports the cutter’s 32 mm diameter for accurate slot form. How does the tooth count affect cutting behaviour? With Z=8 teeth, the cutter distributes cutting forces across multiple edges, improving surface finish and enabling steady material removal while maintaining chip control courtesy of the cross‑cut geometry. What standard ensures profile compatibility with fixtures? Compliance with DIN 851 AB guarantees a standardised tooth form for T‑slot milling, making the machined slots compatible with fixtures and components designed to the same standard. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSS‑Co construction, cross‑toothed cutting geometry and DIN 851 AB compliance for reliable, long‑running slot milling in construction and case‑hardening steels as well as short‑chipping non‑ferrous metals. Order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Maykestag T‑slot cutter DIN 851 AB — 36 mm, HSS‑Co, cross‑toothed, 8 teeth The Maykestag T‑slot cutter offers robust slotting performance for workshop and production use, engineered for engineering steels, case‑hardening steels and short‑chipping non‑ferrous materials HSS‑Co construction for enhanced heat resistance Cross‑toothed cutting geometry for clean chips Complies with DIN 851 AB, Type N standards 36 mm nominal diameter, 25 mm shank diameter Consistent material removal with industrial‑grade HSS‑Co The combination of HSS‑Co and DIN 851 AB specification delivers a balance of toughness and wear resistance that supports continuous milling tasks. Where frequent interruption of production is costly, the alloyed high‑speed steel maintains cutting edge stability under heat and pressure, which reduces the need for frequent regrinds and downtime. This construction therefore promotes longer tool life and stable dimensional control, translating into fewer rejects and a more consistent production flow. Improved chip control and surface quality for shorter rework A cross‑toothed geometry produces short, manageable chips and helps prevent built‑up edge on difficult materials, particularly when machining short‑chipping non‑ferrous metals and various grades of steel. The right‑hand cutting direction and eight cutting edges ensure even load distribution across the cutter, resulting in a more uniform slot wall and reduced manual finishing. For applications requiring slots to meet DIN 650 widths, the reliable chip evacuation supports predictable surface finish and tighter tolerances. Secure clamping and straightforward integration into existing toolholders The cutter’s cylindrical shank with drive flat eases quick clamping in standard collets and toolholders while minimising slippage during heavy cuts. Key dimensions such as the 36 mm nominal diameter, 25 mm shank diameter and compatibility with 20 mm slot widths (DIN 650) allow planners to match the cutter to typical slotting fixtures without custom adaptors. This enables fast setup, consistent runout performance and straightforward repeatability for series production or one‑off workshop tasks. For reliable slot milling with Maykestag’s HSS‑Co performance, contact Metav Werkzeuge for tailored advice and secure supply from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4117802042NW Description: T‑slot cutter, DIN 851 AB, Type N, 36 mm, HSS‑Co, cross‑toothed, 8 teeth Manufacturer: ALPEN‑MAYKESTAG GmbH Packaging unit: 1 Dimensions & core data Nominal diameter d1: 36 mm Shank diameter d2: 25 mm Suitable slot width (DIN 650): 20 mm Teeth: 8 Cutting direction: right‑hand Materials & features Material: HSS‑Co Cutting geometry: cross‑toothed Standard: DIN 851 AB, Type N Shank: cylindrical with drive flat Application: milling construction, case‑hardening and quenched‑and‑tempered steels; short‑chipping non‑ferrous metals FAQ Which materials can be machined with this cutter? The Maykestag T‑slot cutter is suitable for milling construction, case‑hardening and quenched‑and‑tempered steels, and for short‑chipping non‑ferrous metals, as stated in the product specification. What are the key dimensions to consider when selecting a holder? Consider the 36 mm nominal diameter and 25 mm shank diameter; the cutter is designed for slots compatible with DIN 650 (20 mm) and fits standard collets with a drive flat. How does the cross‑toothed geometry affect performance? The cross‑toothed design produces shorter chips and reduces built‑up edge, improving surface finish and reducing manual rework during slotting operations. Is this cutter compatible with high‑speed applications? The HSS‑Co construction provides improved heat resistance compared with plain HSS, offering better durability under elevated cutting temperatures common in workshop and industrial milling. What is the article number for ordering or reference? The article number (SKU) for this T‑slot cutter is 4117802042NW, which should be quoted when enquiring or ordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of HSS‑Co durability and precise cross serration for consistent T‑slot quality; the tool’s 40 mm nominal diameter and 25 mm shank ensure simple integration into common tool holders. Order via Metav Werkzeuge or request application advice from the consultants. T‑slot cutter DIN 851 AB Type N – 40 mm, HSS‑Co, cross serration (MAYKESTAG) The T‑slot cutter DIN 851 AB Type N is a robust milling tool for producing precise T‑slots in construction, case‑hardened and tempered steels as well as in short‑chipping non‑ferrous metals. HSS‑Co construction for long tool life Cross‑serration for improved chip control Compatible with DIN 851 AB and Type N 40 mm nominal diameter, 25 mm shank Durable cutting that extends tool life Manufactured from HSS‑Co, this cutter delivers enhanced hot‑hardness and wear resistance compared with standard high‑speed steels, resulting in a longer tool life under demanding loads. The cobalt alloy composition maintains cutting edge integrity at elevated temperatures, which supports steady performance when machining construction, case‑hardened and tempered steels. The right‑hand cutting geometry further stabilises the cutting process and reduces vibration, giving a reliable basis for repeatable groove quality. Improved chip control and surface finish The cross serration (cross‑toothing) divides chips into shorter segments, which prevents clogging and eases evacuation from the slot. This tooth form is especially beneficial when working with short‑chipping non‑ferrous metals, where continuous chips can otherwise compromise the finish. The result is an improved surface finish and reduced rework, lowering cycle time per part and supporting more predictable downstream processes. Workshop compatibility and straightforward set‑up Designed to the DIN 851 AB Type N standard, the cutter fits established workshop practices and fixturing. The 40 mm nominal diameter combined with a 25 mm shank and a cylindrical shank with a driving flat allows secure clamping in standard collets and tool holders, cutting down set‑up time and minimising run‑in. It is configured to produce grooves to DIN 650 specifications (22 mm groove width), which simplifies component matching and interchangeability across assemblies. Stable production with predictable results Equipped with Z = 10 teeth and a geometry tuned for right‑hand cutting, the tool supports steady material removal rates while maintaining groove dimensional accuracy. Fewer tool changes and predictable wear behaviour contribute to process efficiency and lower per‑part manufacturing cost. As a precision tool for industrial milling, it aligns with workflows that demand repeatability and consistent quality. For specialist advice on integrating the MAYKESTAG T‑slot cutter into production or for supply from Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4117802043NW Label: T‑Nutenfräser DIN 851AB Typ N D.40mm HSS‑Co Verz. Kreuz Z.10 MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Facts Nominal diameter d1: 40 mm Shank diameter d2: 25 mm Teeth: Z = 10 Groove width (DIN 650): 22 mm Special features Material: HSS‑Co Tooth form: cross serration Shank: cylindrical with driving flat Cutting direction: right‑hand cutting Standard: DIN 851 AB Type N FAQ Which materials can be machined with this T‑slot cutter? The T‑slot cutter is suitable for construction, case‑hardened and tempered steels and for short‑chipping non‑ferrous metals, as specified for the MAYKESTAG DIN 851 AB Type N tool. What size groove does the cutter produce according to standards? The tool is designed to produce grooves to DIN 650 with a groove width of approximately 22 mm, matching common T‑slot specifications. How is chip control achieved with this cutter? Chip control is provided by the cross serration tooth form, which breaks chips into short segments and eases evacuation, improving surface finish and process stability. Is the cutter compatible with standard tool holders? Yes. The 25 mm cylindrical shank with driving flat is intended for secure clamping in standard collets and holders, enabling straightforward integration into existing setups. How many teeth does the cutter have and what is the cutting direction? The cutter has 10 teeth (Z = 10) and is configured for right‑hand cutting, supporting a balanced material removal and stable cutting action. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

mit Kreuzverzahnung · HSS-Co · DIN 851 AB · Typ N · zum Fräsen von Bau-, Einsatz- und Vergütungsstählen sowie für kurzspanende NE-Metalle · Zylinderschaft mit Mitnahmefläche · rechtsschneidend Weitere technische Eigenschaften: · Verzahnung: Kreuz · Nenn-Ø d1: 16mm · Schaft-Ø d2: 10mm · für Nuten nach DIN 650: 8mm