Benefit from a well-balanced combination of durable TiAlN protection, a 120° chamfer geometry and a compact Ø10 mm shank for consistent deburring results and reduced rework. Order the cutter directly via Metav Werkzeuge or consult the team for application advice. TECWERK Deburring cutter Ø10 mm — 120° TiAlN, 6‑flute The TECWERK Deburring cutter Ø10 mm — 120° TiAlN, 6‑flute is a precision chamfering and deburring tool designed for workshop and industrial metalworking where reliable edge finishing and repeatable chamfers are required. TiAlN coating for extended tool life 120° chamfer angle for precise deburring Six flutes for smooth material removal Cylindrical shank Ø10 mm, DIN 6535 HB Longer service life through advanced surface engineering The combination of a TiAlN surface treatment on a high‑performance substrate significantly increases resistance to heat and abrasive wear, which lowers the frequency of tool changes and contributes to a more economical production flow. With a compact Ø10 mm shank and a balanced flute geometry the tool reduces chatter and maintains a stable cut, so cycle times remain predictable and process capability improves. These measurable advantages support efficient batch processing and contribute to a lower cost per finished component. Accurate edge preparation that reduces rework A defined 120° chamfer geometry together with six flutes ensures clean burr removal and consistent chamfer dimensions on small bores and edges. The 6 mm cutting length allows precise control when removing material from internal and external edges; this avoids excessive material removal and reduces the need for secondary manual finishing. For customers seeking repeatable results in assemblies, the controlled chamfer profile helps maintain part fit and improves assembly quality. Workshop compatibility and material suitability The tool features a cylindrical shank to DIN 6535 HB with a 10 mm diameter for use in standard collets and holders, enabling fast changeovers at the machine or in the toolroom. The geometry and coating make the cutter very well suited for steel and non‑ferrous metals, and very good for cast iron, while suitability for stainless steel is conditional depending on the cutting parameters and machine rigidity. Designed for right‑hand cutting, the cutter integrates into existing workflows without the need for special tooling. Practical benefits for production and maintenance planning With an overall length of 72 mm the cutter offers a good reach for many chamfering tasks while remaining compact enough for stable clamping. The tool’s configuration reduces the incidence of burr migration and minimises rework, supporting both small repair jobs and series production. Documentation and simple process checks will verify how the cutter reduces downtime: fewer tool changes, consistent edge quality and predictable maintenance intervals help maintain throughput and improve overall equipment effectiveness. For technical guidance, application-specific recommendations or to place an order contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930; Metav’s specialists provide tailored advice and fast delivery from Emmerich Technical data Article number: 2000866749NW Product: Deburring cutter Ø10 mm, 120° TiAlN, 6‑flute Brand: TECWERK Facts Diameter: 10 mm Overall length: 72 mm Cutting length: 6 mm Shank diameter: 10 mm Flutes: 6 Chamfer angle: 120° Special features Coating: TiAlN Material: HSS‑Co Cutting direction: right‑hand cutting Shank: cylindrical shank DIN 6535 HB Product type: forward/reverse deburring cutter Material suitability: steel — very good; non‑ferrous metals — very good; stainless steel — conditionally suitable; cast iron — very good FAQ What materials is the cutter suitable for? The TECWERK Deburring cutter Ø10 mm — 120° TiAlN, 6‑flute is very well suited for steel and non‑ferrous metals, performs very well on cast iron and is conditionally suitable for stainless steel depending on cutting parameters. Can the shank be held in standard collets? Yes, the cylindrical Ø10 mm shank conforms to DIN 6535 HB and fits standard 10 mm collets and holders used in common toolholders. What advantage does the TiAlN coating provide? The TiAlN coating increases heat resistance and wear protection, extending service life and improving performance during higher thermal loads compared with uncoated tools. Is the cutter intended for finishing or heavy stock removal? The tool is optimised for deburring and chamfering rather than heavy stock removal; the six flutes and defined chamfer angle produce a smooth finish and accurate edge geometry. Is the cutting direction right‑hand or left‑hand? This cutter is specified as right‑hand cutting, suitable for conventional machining orientations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

A data inconsistency has been detected for SKU 2000866607NW: the record lists the tool material as HSS‑Co, while the product label and technical enrichment specify VHM (solid carbide) with a TiAlN coating and a 60° countersink geometry. These two material statements are mutually exclusive and affect core technical and application information such as permissible cutting speeds, recommended feed, and material suitability. Because of this contradiction, a reliable, production-ready product description cannot be generated. Please confirm which material is correct—HSS‑Co or VHM (solid carbide)—so that the specification, performance claims and machining recommendations can be prepared without risk of misinformation. For further clarification or to send corrected data, please contact Metav Werkzeuge. For quick assistance: info@metav-werkzeuge.com or call +49 2822 7131930 Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from high‑temperature resistance from the TiAlN coating combined with the toughness of HSS‑Co and a compact 10 mm shank for reliable chamfering and burr removal in production environments; order the tool directly via Metav Werkzeuge or contact the consultants for technical advice. TECWERK Deburring cutter 10 mm, 90° (TiAlN, HSS‑Co, 6 flutes) The Deburring cutter 10 mm 90° is a compact chamfering and deburring tool designed for efficient edge preparation and clean bevels in metalworking and general workshop applications TiAlN coating for extended tool life HSS‑Co construction for wear resistance 6‑flute geometry for smooth deburring 90° chamfer angle for precise bevels 10 mm shank, DIN 6535 HB compatible Durable construction for consistent chamfering performance Constructed from HSS‑Co and finished with a TiAlN coating, this cutter delivers a balance of toughness and heat resistance that keeps cutting edges stable under elevated temperatures. The combination reduces abrasive wear and helps maintain edge geometry over longer runs, which translates into fewer tool changes and less downtime. With a 10 mm diameter and a compact profile, the design supports accurate positioning in standard tool holders while the hard coating improves resistance to thermal softening during continuous operation. Geometry engineered for clean surfaces and efficient chip flow The six‑flute layout and the 90° chamfer geometry provide a controlled cut that produces uniform bevels and minimal burring. The flute count promotes consistent material removal and smooth surface finish, reducing the need for secondary finishing. With a cutting length of 6 mm and an overall length of 72 mm, the tool offers sufficient reach for common chamfering tasks while keeping vibration low. The right‑hand cutting direction facilitates standard set‑ups on most milling and deburring machines. Practical advantages for workshop productivity A 10 mm shank diameter ensures compatibility with common collets and holders, enabling quick tool changes and stable clamping. The cutter’s construction supports resharpening when required, extending service life and helping control running costs without sacrificing precision. In repetitive production settings, the combination of coating and substrate stabilises cutting performance and contributes to consistent part quality, thereby lowering rework rates and improving throughput. Set‑up and application guidance for reliable use Designed for straightforward integration into existing tool stacks, the chamfering tool is suitable for a variety of metalworking tasks where clean edges and precise bevels are required. The right‑hand cutting orientation should be matched to the spindle rotation and feed direction for optimal chip evacuation. For machine set‑up recommendations or details on compatible tool holders, technical teams can provide tailored guidance to ensure the best combination of feed, speed and clamping for the material and operation at hand. For specification checks, compatibility advice or to order the TECWERK deburring cutter, please contact Metav Werkzeuge for expert assistance and reliable supply from Emmerich. Technical data Article number: 2000866638NW Brand: TECWERK Product type: Deburring cutter (forward/reverse deburrer) Label: Entgratfräser D.10mm 90Grad VHM TiAlN HB Z.6 TECWERK Facts Diameter: 10 mm Overall length: 72 mm Cutting length: 6 mm Shank diameter: 10 mm Cutting edges: 6 Chamfer angle: 90° Special features Coating: TiAlN Material: HSS‑Co Cutting direction: right‑hand cut Packaging unit: 1 FAQ What materials is this cutter suitable for? The TECWERK deburring cutter (deburring cutter, SKU 2000866638NW) is designed for general metalworking applications; its HSS‑Co substrate and TiAlN coating suit demanding edge work and higher temperatures. Can the tool be resharpened? Yes, the HSS‑Co construction of the TECWERK deburring cutter allows for resharpening, which can extend service life and reduce overall tooling costs. Which tool holders are compatible with the 10 mm shank? The 10 mm shank fits standard collets and holders designed for a 10 mm diameter; for specific holder recommendations, reference the shank diameter and overall length when selecting clamping systems. Is the cutter suitable for use in automated deburring stations? The geometry and coating of this cutter support continuous operation and consistent results, making it suitable for integration into automated deburring and chamfering workflows. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of solid carbide construction, a TiAlN coating and a precise 60° chamfer geometry delivers consistent deburring quality with extended tool life; order the tool directly via Metav Werkzeuge or consult the team for process recommendations. Deburring Cutter D 12 mm, 60° (Solid Carbide, TiAlN) – TECWERK Deburring Cutter D 12 mm, 60° (Solid carbide, TiAlN) is a precision chamfering tool designed for efficient deburring and chamfering in workshop and light industrial environments Solid carbide, fine-grain core TiAlN coating for thermal resistance 60° chamfer geometry for clean edges 12 mm cylindrical shank to DIN 6535 HB Faster, consistent chamfering for reliable production The 60° chamfer geometry paired with a solid carbide fine-grain substrate ensures precise edge preparation and repeatable results. With six flutes, the cutter produces a smooth surface finish while minimising burr formation, which reduces manual rework and speeds up throughput. The integrated design with a 12 mm cylindrical shank to DIN 6535 HB provides stable clamping in standard tool holders, supporting consistent dimensions on every part. Durable coating that reduces tool changes and downtime The TiAlN coating significantly improves thermal resistance and abrasion performance compared with uncoated tools, extending service life under continuous operation. The fine-grain carbide core complements the coating by maintaining cutting-edge stability, which means fewer tool changes and more productive machine time. This combination translates into lower unit costs over production runs while keeping edge quality at a professional standard. Clear material suitability and machining guidance The cutter is very well suited for steel, very well suited for non-ferrous metals and very well suited for cast iron, while stainless steel (inox) is conditionally suitable; this makes it versatile across common workshop tasks. The universal fine-grain construction enables reliable performance in standard chamfering and deburring operations without complex parameter adjustments. For best results, select a rigid clamping arrangement and moderate axial engagement to preserve surface finish and tool life. Choose the TECWERK deburring cutter for dependable chamfering performance — contact Metav Werkzeuge for tailored machining advice and fast delivery from Emmerich. Technical data Article number: 2000866609NW Product name: Deburring cutter D 12 mm, 60° (Solid carbide, TiAlN) Manufacturer: TECWERK Facts Shank diameter: 12 mm Cutter diameter: 12 mm Chamfer angle: 60° Number of flutes: 6 Special features Solid carbide, universal fine-grain TiAlN-coated Cylindrical shank to DIN 6535 HB Very well suited for steel, non‑ferrous metals and cast iron Conditionally suitable for stainless steel (inox) FAQ Which materials is this deburring cutter best suited for? The deburring cutter D 12 mm, 60° (TECWERK, SKU 2000866609NW) is very well suited for steel, non‑ferrous metals and cast iron; stainless steel is conditionally suitable and may require adjusted feeds and speeds. What advantage does the TiAlN coating provide? The TiAlN coating on the TECWERK deburring cutter increases thermal resistance and wear performance, resulting in longer tool life and fewer tool changes during production. How should the tool be clamped for best results? Use a rigid holder that accommodates a 12 mm cylindrical shank to DIN 6535 HB to ensure stable clamping and consistent chamfer geometry throughout the run. How many cutting edges does the cutter have and what is the benefit? The tool features six flutes, which promote a smooth finish and efficient chip evacuation, supporting fast, clean deburring operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of durable TiAlN coating, solid-carbide construction and a precise 120° chamfer for efficient, low-rework deburring in mixed production environments; order or request consultancy via Metav Werkzeuge for reliable delivery and expert guidance. Deburring cutter D12 mm, 120° TiAlN-coated (TECWERK) — forward/reverse deburring tool with HB shank A Deburring cutter D12 mm designed for chamfering and deburring operations in steel, non‑ferrous metals and cast components, featuring a TiAlN coating and a 12 mm shank to DIN 6535 HB. TiAlN coating for high thermal resistance Solid-carbide shank to DIN 6535 HB 120° chamfer angle for precise deburring Excellent for steel and non‑ferrous metals Faster, more consistent chamfering with less rework The cutter combines a 120° chamfer geometry with six cutting edges to deliver smooth deburring and consistent chamfer profiles on a variety of components. The TiAlN coating ensures enhanced heat resistance and wear protection, which translates into longer tool life and fewer tool changes during batch production. For production planners this means a measurable increase in process uptime and a reduced rate of secondary finishing, supporting efficient throughput and predictable cycle times. Built for secure clamping and versatile workshop use With a 12 mm shank manufactured to DIN 6535 HB standards and a right‑hand cutting direction, the tool guarantees secure clamping in common collet systems and stable cutting behaviour during rapid operations. The design supports both forward and reverse deburring tasks, making it suitable for workshops and industrial settings that require a single, reliable tool for both manual and machineised chamfering. Suitability is noted as very good for steel, non‑ferrous metals and cast parts, while stainless steel applications are conditionally supported. Clear technical benefits for process engineers Key dimensions — diameter 12 mm, cutting length 6 mm, overall length 83 mm — define the working envelope and allow straightforward integration into existing tool lists. The combination of solid‑carbide construction and a fine‑grain substrate provides the rigidity needed for accurate edge formation, while the TiAlN layer reduces built‑up edge and thermal wear. The tool, identified as SKU 2000866751NW, is optimised for operators who prioritise repeatable edge quality and minimal post‑processing. Contact Metav Werkzeuge for tailored procurement advice and secure supply of this TECWERK deburring cutter, with expert support from Emmerich for fast and reliable delivery. Technical data Article number: 2000866751NW Label: Entgratfräser D.12mm 120Grad VHM TiAlN HB Z.6 TECWERK Brand: TECWERK Product type: Vor-/Rückwärtsentgrater Packaging unit: 1 Facts Diameter: 12 mm Shank diameter: 12 mm Cutting length: 6 mm Overall length: 83 mm Chamfer angle: 120° Cutting edges: 6 Cutting direction: right‑handed Special features TiAlN coating Solid carbide, universal fine‑grain substrate Cylindrical shank to DIN 6535 HB Designed for chamfering and deburring Very good suitability: steel, non‑ferrous metals, cast iron Conditionally suitable: stainless steel FAQ What materials is this deburring cutter suitable for? The TECWERK deburring cutter is very well suited to steel, non‑ferrous metals and cast iron; stainless steel applications are conditionally supported depending on the specific grade and machining parameters. What are the key dimensions to consider for machine setup? Relevant dimensions include a 12 mm diameter, 12 mm shank diameter, 6 mm cutting length and 83 mm overall length; these ensure compatibility with standard collets and toolholders. How does the TiAlN coating improve performance? TiAlN increases thermal resistance and reduces wear during high‑temperature cutting, resulting in longer tool life and more consistent edge quality when using the TECWERK cutter. Can the tool be used on automatic chamfering machines? Yes, the solid‑carbide construction and DIN 6535 HB shank make the cutter suitable for machineised chamfering and deburring applications where secure clamping is required. What cutting direction does the tool have? The cutter is right‑hand cutting, designed for conventional forward machining and effective edge formation. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Product data conflict: the material is listed as "HSS‑Co" while another field specifies "VHM" (solid carbide); please verify the source data to ensure accuracy and consistency. This discrepancy could lead to confusion or errors in the selection process, so it is essential to confirm which material designation is correct. Double-checking the original documentation or consulting with the relevant team may help clarify the issue. Accurate material identification is crucial for proper application, performance, and compatibility, so resolving this conflict promptly is highly recommended. Ensuring the data aligns across all fields will prevent potential misunderstandings or complications in the future.

Take advantage of the combination of a 120° cutting geometry, TiAlN wear-resistant coating and a compact 4 mm shank to achieve consistent chamfers and clean deburring in confined spaces; order the tool directly via Metav Werkzeuge or consult the team for application advice. Deburring cutter D 4 mm 120° VHM TiAlN HB Z.4 (TECWERK) — Chamfering and deburring cutter for precision edge finishing The Deburring cutter D 4 mm 120° VHM TiAlN HB Z.4 (TECWERK) is designed for controlled chamfering and reliable removal of burrs on machined parts, especially where access is limited and repeatable edge quality is required 120° chamfer for precise edge finishing TiAlN coating for extended tool life 4 mm shank for compact machining Very good for steel and non-ferrous metals Consistent edge geometry for repeatable results The 120° cutting angle is optimised to produce uniform chamfers and tidy edges on turned, milled or drilled components. As a compact chamfering tool with a 4 mm shank, it enables access to narrow bores and tight features while maintaining stable cutting performance. The multi-flute design with Z.4 ensures balanced material removal and reduces the need for secondary hand deburring, lowering rework time and improving throughput. Durable coating and tool composition for longer service life Equipped with a TiAlN surface layer, the cutter resists thermal wear and maintains hardness at elevated temperatures, which extends tool life under interrupted cuts. The tool body is produced as VHM (solid carbide) in a universal fine-grain grade, providing rigidity and wear resistance for frequent use. TiAlN is particularly effective where higher cutting temperatures occur, ensuring a more predictable maintenance cycle and fewer tool changes. Clear material suitability for reliable application planning The tool is rated very good for use on steel, non-ferrous metals and cast iron, and conditionally suitable for stainless steels. This classification helps prioritise the cutter for typical workshop tasks—deburring machined steel components and finishing brass or aluminium parts—while signalling caution for demanding stainless applications where process parameters must be adapted. Practical shank standard and cutting direction for machine compatibility The cylindrical shank conforms to DIN 6535 HB, enabling secure clamping in standard tool holders and collets. The cutter is manufactured as a right-hand cut, which suits most conventional spindle directions and simplifies integration into existing operations. With an overall length of 54 mm and a cutting length of 4 mm, the design balances accessibility with adequate reach for common chamfer depths. Contact Metav Werkzeuge for tailored application guidance on the TECWERK chamfering and deburring cutter D 4 mm 120° VHM TiAlN HB Z.4 and to arrange procurement or technical consultation directly from Emmerich. Technical data Article number: 2000866743NW Brand: TECWERK Product type: Chamfering/deburring cutter Facts Diameter: 4 mm Overall length: 54 mm Cutting length: 4 mm Shank Ø: 4 mm Countersink angle: 120° Number of flutes: 4 Special features Coating: TiAlN Tool material: VHM (solid carbide), universal fine-grain Shank: cylindrical, DIN 6535 HB Cutting direction: right-hand cut Application: chamfering and deburring Material suitability: steel (very good), non-ferrous metals (very good), cast iron (very good), stainless steel (conditionally suitable) FAQ What materials can this chamfering cutter process? The Deburring cutter D 4 mm 120° VHM TiAlN HB Z.4 (TECWERK, SKU 2000866743NW) is very well suited for steel, non-ferrous metals and cast iron; it is conditionally suitable for stainless steels. What does the TiAlN coating provide? The TiAlN coating increases thermal resistance and wear protection, prolonging service life of the TECWERK cutter under higher cutting temperatures. What size shank and mounting standard does the tool use? The tool has a 4 mm cylindrical shank manufactured to DIN 6535 HB, compatible with standard collet holders and small-tool fixtures. How many flutes does the cutter have and why does it matter? The cutter has 4 flutes (Z.4); this configuration offers balanced cutting action and smoother edge formation during chamfering and deburring operations. Is the cutter suitable for use in tight bores and compact features? Yes; with a 4 mm diameter and a 54 mm overall length, the cutter is intended for confined spaces where precise edge finishing is required. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Data inconsistency detected for SKU 2000866601NW: the supplied product fields contain contradictory information that prevents the creation of a reliable product description. The label and auxiliary description reference "VHM" (solid carbide), while the material field is listed as "HSS‑Co" (cobalt high‑speed steel). These two specifications are mutually exclusive for a cutting tool and affect key technical attributes such as coating adhesion, suitable cutting speeds and material applications. Please correct the product data by confirming whether the tool is solid carbide or HSS‑Co and ensure related fields (coating, shank standard, cutting geometry) are consistent. Once the material specification is clarified, a full, production‑ready description can be generated. For further assistance, contact info@metav-werkzeuge.com or call +49 2822 7131930.

Benefit from the combination of TiAlN surface protection, a 4 mm shank and a precise 90° countersink geometry for dependable chamfering and clean edge breaking; order the TECWERK deburring cutter directly via Metav Werkzeuge or ask our consultants if needed. TECWERK Deburring Cutter D 4 mm — TiAlN-coated HSS‑Co, 90° chamfer The TECWERK 4 mm deburring cutter is a compact forward/reverse tool for precision chamfering and edge finishing in metalworking, designed for workshop and production use TiAlN coating for extended tool life HSS‑Co construction for robust performance 90° countersink angle for precise chamfers High tool life through advanced coating and steel grade The cutter combines a TiAlN surface coating with a HSS‑Co core to deliver improved heat resistance and wear performance. The result is longer productive intervals between regrinds or replacements, translating to lower downtime and reduced tooling costs. This paragraph emphasises the measurable advantage of a coated high-speed steel tool: sustained cutting performance under elevated temperatures while maintaining edge integrity for consistent chamfers. Precise geometry for repeatable chamfers and clean deburring With a defined 90° countersink angle and four cutting edges, the tool produces uniform chamfers and reliable edge removal on a range of components. The shank Ø 4 mm and a cutting length of 4 mm make the cutter suitable for tight toolholders and compact setups, enabling accurate machining where space is limited. The fixed geometry simplifies setup, so cycle times stay predictable and quality remains consistent across batches. Material suitability and efficient workshop integration The design is optimised for everyday workshop materials: very good suitability for steel, very good suitability for non‑ferrous metals, and very good suitability for cast iron, with conditional suitability for stainless steel. The right‑hand cutting direction supports standard spindle rotations and reduces the need for special fixturing. Thanks to the cylindrical shank made to DIN 6535 HB, the cutter integrates seamlessly into conventional collets and toolholders, allowing fast changeovers and steady repeatability in production runs. For precision chamfering and reliable edge finishing with TECWERK quality, contact Metav Werkzeuge for personalised advice and dependable supply from Emmerich — our consultants are ready to assist with technical queries and ordering. Technical data Article number: 2000866635NW Product type: Forward/reverse deburring cutter Brand: TECWERK Coating: TiAlN Material: HSS‑Co Data Diameter: 4 mm Shank diameter: 4 mm Overall length: 54 mm Cutting length: 4 mm Countersink angle: 90° Cutting direction: Right‑hand cutting Number of cutting edges: 4 Special features Cylindrical shank to DIN 6535 HB Intended for chamfering and deburring Very good suitability for steel Very good suitability for non‑ferrous metals Very good suitability for cast iron Conditional suitability for stainless steel FAQ What materials is this cutter best suited for? The TECWERK deburring cutter (SKU 2000866635NW) is very well suited for steel, non‑ferrous metals and cast iron, with conditional suitability for stainless steel. Can this tool be used in standard collets and toolholders? Yes, the cutter has a cylindrical shank to DIN 6535 HB and a shank diameter of 4 mm, allowing compatibility with common collets and compact toolholders. How does the TiAlN coating benefit workshop operations? The TiAlN coating on this HSS‑Co cutter increases heat resistance and wear protection, extending cutting life and reducing the frequency of tool changes during production. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of TiAlN coating, a 120° chamfer angle and four flutes for reliable edge finishing and repeatable results; order the cutter directly via Metav Werkzeuge or contact our consultants for application advice. TECWERK Deburring Cutter 6 mm, 120° TiAlN, 4 flutes The TECWERK deburring cutter 6 mm 120° TiAlN is a compact forward/reverse deburring tool designed for precise chamfering and edge finishing in steel and non‑ferrous materials Solid carbide, fine-grain TiAlN coating 120° chamfer angle for clean edge preparation 4 flutes for smooth deburring action Suitable for steel and non-ferrous metals Reliable chamfering that improves process consistency The TECWERK deburring cutter 6 mm 120° TiAlN combines a TiAlN surface layer with a fine-grain solid‑carbide substrate to deliver extended tool life and consistent cutting behaviour. The 120° cutting geometry produces a defined chamfer that reduces edge stress and improves part fit‑up, while the four‑flute configuration ensures even material removal and a low‑vibration cut. This leads to fewer rework steps and a more predictable finishing operation, especially in small‑batch and series production environments where repeatability matters. Durable construction and broad material suitability A ceramic‑style TiAlN coating increases thermal resistance and reduces built‑up edge, improving performance on higher temperatures and tougher alloys. The tool is engineered with a cylindrical shank to DIN 6535 HB and a nominal 6 mm shaft for secure clamping and compatibility with standard toolholders. Application data indicate very good suitability for steel, non‑ferrous metals and castings, with conditional suitability for stainless steel; this enables flexible deployment across maintenance, fabrication and light machining tasks while reducing the need for multiple specialised cutters. Integration into workshop workflows and handling tips With a total length of 57 mm and an effective cutting length of 4 mm, the cutter fits compact tool chains and offers straightforward set‑up on drilling or milling spindles that accept a 6 mm shank. The right‑hand cutting direction and four cutting edges give a balanced removal rate and help maintain surface quality during deburring operations. For best results, start with conservative feeds and speeds and increase progressively while monitoring finish; the TiAlN layer supports higher thermal loads, allowing modest speed boosts where machine and workpiece allow. For precision deburring with TECWERK quality and direct support from Metav Werkzeuge, request availability or application guidance by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000866745NW Label: Entgratfräser D.6mm 120Grad VHM TiAlN HB Z.4 TECWERK Manufacturer: TECWERK Product type: Vor-/Rückwärtsentgrater Dimensions & core data Diameter: 6 mm Total length: 57 mm Cutting length: 4 mm Shank diameter: 6 mm Countersink angle: 120° Number of flutes: 4 Cutting direction: right‑hand Features & applications TiAlN coating Solid carbide, universal fine‑grain Cylindrical shank to DIN 6535 HB For chamfering and deburring Very well suited: steel, non‑ferrous metals, castings Conditionally suited: stainless steel Packaging unit: 1 FAQ Is this cutter suitable for steel? The TECWERK deburring cutter (SKU 2000866745NW) is rated as very well suited for steel and provides reliable chamfering and edge finishing. What shank diameter is required for clamping? The tool has a 6 mm cylindrical shank to DIN 6535 HB and requires a collet or holder that accepts a 6 mm shank. What advantages does the TiAlN coating offer? TiAlN increases thermal resistance and reduces built‑up edge; in this deburring cutter it helps maintain cutting performance and tool life under higher thermal loads. Can this cutter be used on stainless steel and castings? The cutter is very well suited for castings and is conditionally suitable for stainless steel; performance on inox depends on machining parameters and alloy specifics. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combining a TiAlN surface with a precise 60° chamfer and a 4-flute geometry delivers durable, repeatable deburring performance for series production. The compact design with a 6 mm shank and 57 mm overall length makes integration straightforward; order the deburring cutter directly via Metav Werkzeuge or ask our consultants if needed. Deburring cutter 6 mm, 60° TiAlN — TECWERK The Deburring cutter 6 mm, 60° TiAlN is a compact forward/backward deburring tool for fast chamfering and clean edge removal in workshop and production applications. TiAlN hard-wearing coating 60° chamfer for clean deburring 4-flute geometry for smooth finish Shank Ø 6 mm fits standard holders Consistent, faster deburring for production environments The combination of a narrow 60° chamfer and a 4-flute geometry produces a clean, controllable edge with reduced vibration and improved surface finish, which means fewer rework cycles and shorter processing times. The relatively short cutting length (4 mm) and the overall compact profile ensure stable cutting conditions when mounted in standard tool holders, helping to maintain cycle-time reliability on milling centres and specialised deburring stations. This efficiency supports higher throughput without compromising the quality of the chamfer. Broad material suitability explained for practical selection This cutter is rated very well for steel, non-ferrous metals and cast materials; performance on stainless steel (INOX) is listed as conditionally suitable, which implies adjustments to feeds and speeds may be required. Where alloys or heat-treated components are concerned, the tool’s geometry promotes predictable chip evacuation on softer materials and controlled shearing on harder substrates. Selecting appropriate spindle speed and feed—guided by material class and machine capability—reduces tool wear and prevents thermal damage to workpiece edges. Coating and tool life: why TiAlN matters The TiAlN coating increases surface hardness and thermal stability at the cutting edge, delaying oxidation and reducing built-up edge under higher temperatures. In practice, the coating extends tool life in medium-duty finishing operations and preserves consistent edge quality over longer production runs. For customers less familiar with coating technology, TiAlN offers measurable benefits in demanding cycles: higher temperature tolerance, better wear resistance and improved performance where intermittent contact with tighter tolerances occurs. Integration, handling and mounting benefits The cylindrical shank manufactured to DIN 6535 HB standards and the common 6 mm diameter make the cutter straightforward to mount in collets and tool holders commonly found in small mills and dedicated deburring units. The right-hand cutting orientation suits standard spindle rotations without additional adapter tooling. Routine handling is uncomplicated: simple inspection of the cutting edges and basic regrinding routines (where applicable) keep the tool in service. For manufacturers aiming for reproducible edge quality, the mechanical compatibility and compact form factor ease insertion into existing process chains. For application advice, cutting data recommendations or to secure TECWERK deburring cutters for immediate production use, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 2000866603NW Brand: TECWERK Product type: Forward/backward deburring cutter Packaging unit: 1 Core data Diameter: 6 mm Overall length: 57 mm Cutting length: 4 mm Shank diameter: 6 mm Chamfer angle: 60° Number of flutes: 4 Cutting direction: right-hand cutting Special features Coating: TiAlN Designed for chamfering and deburring Shank type: cylindrical shank to DIN 6535 HB Materials suitability: steel very well suited Materials suitability: non-ferrous metals very well suited Materials suitability: cast very well suited Materials suitability: stainless steel (INOX) conditionally suitable FAQ What shank diameter and overall length does the cutter have? The TECWERK deburring cutter (SKU 2000866603NW) has a 6 mm shank and an overall length of 57 mm, making it compatible with standard 6 mm collets and holders. Which materials is the tool best suited for? The Deburring cutter 6 mm, 60° TiAlN is very well suited for steel, non-ferrous metals and cast materials; stainless steel (INOX) is conditionally suitable and may require adjusted cutting data. How does the TiAlN coating improve performance? The TiAlN coating on this cutter increases thermal resistance and surface hardness, extending tool life and reducing built-up edge during finishing operations under elevated temperatures. Is the cutter suitable for use in automated deburring stations? The compact geometry, 4-flute design and standard 6 mm shank allow reliable integration into automated deburring stations and compact milling setups for consistent chamfering. What chamfer angle does the tool produce and what is its application? The tool produces a 60° chamfer, suitable for creating defined edge breaks and preparing parts for assembly or for subsequent coating and finishing processes. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a TiAlN-coated, fine-grain solid carbide design and a precise 90° chamfer geometry to speed up deburring tasks while extending tool life; order directly via Metav Werkzeuge or consult the technical team for application support. Deburring cutter Ø 6 mm, 90° – TECWERK TiAlN, 4-flute forward/reverse deburring cutter Deburring cutter Ø 6 mm, 90° by TECWERK designed for precise chamfering and fast edge breaking in a wide range of workshop materials. TiAlN coating for high heat resistance 90° chamfer for precise edge breaking Four-flute geometry for fine finish 6 mm cylinder shank to DIN 6535 HB Faster, more durable chamfering with industrial coating The combination of a TiAlN surface and a solid carbide fine-grain substrate delivers increased hardness at elevated temperatures and a longer service life under continuous use. This makes the cutter particularly suited to operations that demand repeatable chamfer quality and reduced tool changes. The 90° geometry ensures defined bevels and consistent edge breaking, while the fine-grain carbide substrate improves cutting stability and reduces vibration, resulting in reliable machining results across series production and single-part runs. Consistent finish and wide material compatibility The four-flute configuration provides a balanced cut and a smooth surface finish with minimal burr formation. With a cutting length of 4 mm and a total length of 57 mm, the cutter offers sufficient reach for standard chamfering tasks while keeping tool overhang low for greater rigidity. Material suitability is documented as very good for steel, non-ferrous metals, and cast iron, with INOX (stainless steel) rated as conditionally suitable — this means adjustments to cutting speed and feed are recommended when working with highly alloyed stainless steels to protect geometry and coating. Workshop integration and handling advantages A 6 mm cylinder shank manufactured to DIN 6535 HB facilitates secure clamping in standard collets and holders, helping to expedite tool changes and maintain concentricity. The cutter’s right-hand cutting direction and forward/reverse capability expand its application in multi-directional deburring processes. Clear specifications and a robust coating reduce unplanned downtime and complement a workflow focused on throughput and repeatable quality, making it a practical choice for machine shops and fabrication environments aiming to streamline finishing operations. For precise chamfering with TECWERK's TiAlN performance and reliable availability from Emmerich, contact Metav Werkzeuge for purchase and application advice at info@metav-werkzeuge.com or +49 2822 7131930 — our consultants will confirm suitability and delivery from stock. Technical data Article number: 2000866636NW Description: Deburring cutter, Ø 6 mm, 90°, VHM, TiAlN, 4 flutes Product type: Forward/reverse deburring cutter Brand: TECWERK Specifications Diameter: 6 mm Total length: 57 mm Cutting length: 4 mm Shank Ø: 6 mm Number of flutes: 4 Countersink angle: 90° Cutting direction: right-hand Packaging unit: 1 Features Coating: TiAlN Substrate: solid carbide · universal fine-grain Shank type: cylinder shank to DIN 6535 HB Very good suitability for steel Very good suitability for non-ferrous metals Very good suitability for cast iron Conditionally suitable for INOX (stainless steel) FAQ What materials can this cutter handle best? The deburring cutter Ø 6 mm from TECWERK is rated very good for steel, non-ferrous metals and cast iron; stainless steel (INOX) is conditionally suitable and may require adjusted cutting parameters. How should the tool be clamped for best results? Use a standard collet or holder that accepts a 6 mm cylinder shank to DIN 6535 HB to ensure concentricity and rigidity for repeatable chamfering with the TECWERK deburring cutter. Is the TiAlN coating beneficial for high-speed use? Yes, the TiAlN coating increases heat resistance and wear protection, enabling higher cutting speeds and longer tool life under demanding conditions when using the TECWERK VHM cutter. What edge finish can be expected from the four-flute geometry? The four-flute design produces a finer finish and reduced burr formation compared with fewer-flute tools, delivering clean chamfers with consistent profiles using the TECWERK cutter. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Product data conflict: the field "material" is listed as HSS‑Co, while the technical enrichment specifies VHM (solid carbide) with TiAlN coating; this discrepancy creates confusion and prevents accurate classification of the product. To ensure consistency and clarity, it is essential to resolve this issue by verifying the correct material information. Please supply corrected data promptly, as this will allow us to proceed with generating an accurate and detailed product description. Without this clarification, there is a risk of misrepresentation, which could lead to misunderstandings or errors in product usage. Your cooperation in addressing this matter is greatly appreciated.

Take advantage of the combination of precision chamfering, robust TiAlN protection and a compact Ø 8 mm shank for consistent deburring results; order the tool directly via Metav Werkzeuge or ask the consultants for application advice. Deburring cutter D.8 mm, 60° VHM, TiAlN (TECWERK) The Deburring cutter D.8 mm, 60° VHM, TiAlN by TECWERK offers precise chamfering and fast edge clean-up for workshop and production use Solid carbide VHM, universal fine grain TiAlN coating for improved wear resistance 60° chamfer angle for precise deburring DIN 6535 HB cylindrical shank Ø 8 mm Consistent edge quality with controlled 60° chamfering The 60° geometry delivers a repeatable chamfer suitable for preparation before welding, thread starts and aesthetic finishing. The tool’s 5 flutes design promotes balanced cutting forces and a clean edge without smearing, which reduces subsequent finishing work. For applications requiring short, repeatable passes, the combination of a defined 5 mm cutting length and the compact overall length ensures controlled engagement and predictable results across batches. Extended tool life through advanced coating and carbide grade A TiAlN coating increases thermal resistance and reduces adhesive wear at elevated temperatures, extending productive tool life under interrupted cuts and higher spindle speeds. The substrate is manufactured as solid carbide (VHM) with a fine-grain microstructure to combine toughness and abrasion resistance. In practical terms, the coating and substrate reduce downtime for tool changes and maintain edge quality longer, which supports cost-effective production cycles and higher throughput. Proven compatibility with common workshop materials The cutter is optimised for metalworking: very well suited for steel, non-ferrous metals and cast iron, while use on stainless steels is possible with adjusted feeds and speeds. The right-hand cutting direction and DIN 6535 HB cylindrical shank Ø 8 mm ensure stable clamping in standard tool holders and handheld machines alike. Where precise deburring and chamfering are needed on varied workpieces, the tool provides a balance of aggressiveness and finish to reduce rework and speed up downstream processes. Practical benefits for workshop workflows A short, dedicated cutting length and robust shank geometry simplify tool handling and reduce the need for special holders. The tool’s build supports quick changeovers and predictable run-out behaviour, which is especially relevant in small-batch production and repair work. For workshops seeking to consolidate tooling, this cutter combines chamfering and deburring functionality in one operation, saving time and minimising the number of tool set-ups required. For ordering, technical consultation or to discuss suitability for specific materials, contact Metav Werkzeuge—fast delivery and expert advice from Emmerich are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866605NW Label: Deburring cutter D.8 mm 60° VHM TiAlN HB Z.5 TECWERK SKU: 2000866605NW Facts Diameter: 8 mm Cutting length: 5 mm Overall length: 63 mm Shank diameter: 8 mm Number of flutes: 5 Chamfer angle: 60° Cutting direction: right-hand Packaging unit: 1 UID: 2000866605NW Special features Solid carbide (VHM) · universal fine-grain TiAlN-coated for thermal and wear resistance DIN 6535 HB cylindrical shank Suitable for steel: very good Suitable for non-ferrous metals: very good Suitable for cast iron: very good Suitable for stainless steel: conditionally suitable Designed for chamfering and deburring applications FAQ What materials is the cutter suitable for? The Deburring cutter D.8 mm, 60° VHM, TiAlN is very well suited for steel, non-ferrous metals and cast iron; stainless steel is possible with adapted parameters. How does the TiAlN coating affect performance? The TiAlN coating on the TECWERK deburring cutter reduces adhesive wear and increases thermal resistance, which helps maintain edge life during demanding chip conditions. Which clamping standard fits the shank? The tool carries a DIN 6535 HB cylindrical shank Ø 8 mm for reliable clamping in standard collets and tool holders. What is the advantage of a 60° chamfer angle? A 60° chamfer produces a clear, repeatable edge suitable for weld preparation, thread lead-ins and visible finishes while minimising material removal. Is the cutter suitable for hand-held machines? With a robust DIN 6535 HB shank Ø 8 mm and a compact overall length, the cutter can be used in stable hand-held setups when operated within recommended speeds and feeds. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of TiAlN-coated longevity combined with a 90° chamfer and a compact 5 mm cutting length for reliable edge finishing; order the TECWERK deburring cutter directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Deburring Cutter D 8 mm, 90° – VHM, TiAlN-coated, 5 flutes The TECWERK Deburring Cutter D 8 mm is a solid-carbide chamfering and deburring tool designed for precise 90° bevelling and efficient edge finishing in industrial metalworking applications. TiAlN coating for extended tool life 90° chamfer for precise bevelling 5 flutes for smooth surface finish Solid carbide shank, DIN 6535 HB Excellent for steel and non-ferrous metals Precise 90° chamfers that reduce rework and improve assembly fit A consistent 90° chamfer delivered by a tool with 5 flutes and a 5 mm cutting length ensures repeatable edge geometry and minimal manual finishing. The combination of a short, focused cutting zone and a fine-flute design produces a smooth edge that reduces burr remnants and the need for downstream correction. For production environments where parts must fit accurately or sealing faces require uniform edges, this cutter gives measurable improvements in cycle-time and quality control while maintaining consistent results across batches. Coating and construction engineered for longer tool life and uptime The TiAlN surface treatment and VHM (solid carbide) construction provide thermal stability and wear resistance under continuous machining. With an 8 mm shank manufactured to DIN 6535 HB, the tool seats securely in standard collets for minimal runout and vibration. These properties translate into fewer tool changes and predictable performance across long runs, improving throughput. The robust design benefits small-batch workshops and larger production lines alike by lowering total tooling consumption and stabilising finishing costs. Versatile material compatibility to simplify tool planning Designed for chamfering and deburring, the cutter is optimised for a broad range of materials: very good suitability for steel and non-ferrous metals, very good suitability for cast iron, and conditional suitability for stainless steel. Its right-hand cutting action and universal fine-grain geometry make it suitable for both rough edge removal and fine finishing tasks. This versatility reduces the need for multiple specialised cutters, streamlining inventory and helping procurement keep a tighter, more economical toolset. Contact Metav Werkzeuge today for tailored advice on the TECWERK deburring cutter and to request an application-specific recommendation from our specialists at Metav Werkzeuge; delivery and consultation from Emmerich are available to ensure the right tool for the job. Technical data Article number: 2000866637NW Name: Deburring cutter D 8 mm, 90°; TECWERK Product type: Forward/reverse deburring cutter Specifications Diameter: 8 mm Overall length: 63 mm Cutting length: 5 mm Shank diameter: 8 mm Number of flutes: 5 Chamfer angle: 90° Cutting direction: right-hand Features Coating: TiAlN Solid carbide (VHM) · Universal fine-grain Cylindrical shank per DIN 6535 HB For chamfering and deburring Suitability: steel very good, non‑ferrous metals very good, cast iron very good, stainless steel conditionally suitable FAQ What materials can be machined with this cutter? The TECWERK deburring cutter is very well suited for steel, non‑ferrous metals and cast iron, with conditional suitability for stainless steel as noted in the specifications. Is the shank compatible with standard toolholders? Yes, the tool features an 8 mm cylindrical shank to DIN 6535 HB, making it compatible with common collets and holders specified for that standard. How many flutes does the cutter have and what surface quality can be expected? The cutter has 5 flutes, which support a smooth surface finish and effective burr evacuation for consistent edge quality. Can this cutter be used in both forward and reverse deburring operations? The product type is specified as a forward/reverse deburring cutter, and its right‑hand cutting geometry is optimised for standard deburring tasks in typical machining setups. What are the main benefits of the TiAlN coating on this tool? The TiAlN coating increases heat resistance and wear life, enabling longer tool life and more stable cutting performance in demanding finishing applications. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund