Take advantage of a solid carbide single-flute design and a 25° helix for secure machining of thin-walled non‑ferrous parts; order directly via Metav Werkzeuge or ask the consultants for application advice. Single-flute End Mill Type W, D 10 mm, Solid Carbide, 25° – TECWERK The single-flute end mill Type W is a long, solid‑carbide finishing cutter with a cylindrical shank, designed for precision machining of thin‑walled profiles in non‑ferrous metals and plastics. Solid carbide construction, universal fine grain Single‑flute geometry for chip evacuation 25° helix optimised for thin walls Cylindrical shank DIN 6535 HA Improve throughput on delicate components with single‑flute efficiency The single‑tooth geometry delivers effective chip evacuation and reduced rubbing, making the tool especially suitable for thin‑walled parts and long reaches. The single‑flute layout minimises build‑up at the cutting edge, which helps maintain consistent surface finish and reduces the risk of material deformation when machining profiles or sections made from light alloys and plastics. This construction supports higher feed per tooth while keeping cutting forces controlled. Confident material compatibility for aluminium and non‑ferrous alloys Engineered in solid carbide (VHM) with a universal fine‑grain grade, the cutter is tailored for non‑ferrous metals and plastics, including aluminium alloys up to 7% silicon. The 25° helix angle promotes gentle entry and exit behaviour in soft and abrasive aluminium grades, lowering the chance of burrs on thin walls. Where alloys and polymers demand careful tool selection, the tool’s geometry provides a balance of durability and surface quality. Secure toolholding and reliable concentricity for long tools The long version with a cylindrical shank to DIN 6535 HA ensures compatibility with standard toolholders and collets while helping to preserve run‑out accuracy over extended overhangs. Precise shank tolerances reduce vibration and improve repeatability in serial production. For workshop setups that require predictable performance on extended contours, this design helps maintain dimensional consistency and reduces rework. Practical choice to reduce setup complexity and machining time Right‑hand cutting and a single flute make the tool straightforward to programme into existing processes and to integrate where chip control is paramount. The 25° helix and the fine‑grain carbide promote stable cutting at moderate to elevated feed rates in suitable materials, helping to shorten cycle times without compromising finish. For operations that value a clean swarf flow and fewer operator interventions, the tool offers a practical advantage. For personalised technical advice or to secure this TECWERK single‑flute end mill through Metav Werkzeuge, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for tailored support. Technical data Article number: 2000806616NW Product: Single‑flute end mill Type W, D 10 mm, solid carbide, long Manufacturer: TECWERK Numbers / Core technical data Diameter: 10 mm Helix angle: 25° Number of flutes: 1 Package unit: 1 Internal ID: 2000806616NW Special features / Versions Material: solid carbide (VHM), universal fine grain Shank: cylindrical shank to DIN 6535 HA Cutting direction: right‑hand Application: thin‑walled workpieces, profiles in non‑ferrous metals and plastics Suitable for aluminium alloys with up to 7% silicon Long version for extended reach FAQ Is this cutter suitable for aluminium alloys with silicon content? Yes, the TECWERK single‑flute end mill is specified for aluminium alloys with a silicon content up to 7%, making it suitable for many common aluminium extrusion and profile applications. What is the shank type and compatibility with toolholders? The tool features a cylindrical shank to DIN 6535 HA, designed for use with standard collets and toolholders that accept DIN 6535 HA shanks. How many flutes does the cutter have and why is that beneficial? The cutter has a single flute (one cutting edge), which improves chip evacuation and reduces heat build‑up when machining thin‑walled or long recessed features. Can this tool be used on plastics as well as metals? Yes, the tool is intended for both non‑ferrous metals and plastics; the geometry supports clean cutting in polymers and reduces the risk of melting or smearing. Is the tool coated? The available data specifies the tool material as solid carbide with a universal fine‑grain grade; no coating is indicated in the provided information. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a robust combination of solid carbide construction, a 25° helix and a long cylindrical shank for reliable machining of thin-walled non‑ferrous parts; order directly via Metav Werkzeuge or consult the team for application support. Single-flute cutter Type W Ø12 mm – solid carbide, 25° helix (TECWERK) A Single-flute cutter Type W Ø12 mm designed for machining thin‑walled profiles and components in non‑ferrous metals and plastics, supplied with a long cylindrical shank to suit industry collets. Solid carbide, ultra-fine grain Long design with cylindrical shank DIN 6535 HA 25° helix angle, right-hand cutting Optimised for thin-walled non‑ferrous parts Consistent precision for thin-walled components The single‑flute geometry provides controlled cutting engagement that reduces radial forces, which is essential when working on thin‑walled profiles. This results in improved dimensional stability and fewer distortions during machining. The tool's solid carbide composition and fine‑grain microstructure maintain edge integrity, so tolerances are kept tight across repeated runs while preserving component geometry. Efficient chip evacuation and improved surface finish With only one flute and a pronounced 25° helix, chip evacuation is rapid and uninterrupted, especially when cutting aluminium alloys and softer non‑ferrous materials. The combination of flute geometry and helix angle reduces recutting of chips and lowers heat build‑up, which contributes directly to a cleaner surface finish and reduced secondary finishing work. The result is a shorter overall process time for profile production. Secure clamping and vibration resistance for long runs The long configuration with a cylindrical shank per DIN 6535 HA allows stable clamping in standard holders, improving concentricity and reducing chatter on extended reaches. This stability benefits throughput and tool life by maintaining consistent cutting conditions. The right‑hand cutting design ensures predictable milling behaviour with common spindle directions, making the cutter suitable for automatic production cycles. Versatile suitability across non‑ferrous and plastics Engineered for non‑ferrous metals and technical plastics, the tool handles aluminium alloys with silicon contents up to 7% effectively, while remaining appropriate for a range of profiles and sections. The fine‑grain carbide substrate provides wear resistance during extended engagement, supporting economic machining by reducing tool changes. For delicate profile work, this cutter balances material compatibility with productivity. Contact Metav Werkzeuge for tailored application advice and reliable delivery from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 2000806617NW Label: Einzahnfräser Typ W D.12mm VHM 25Grad HA Z.1 lang TECWERK Packing unit: 1 Manufacturer: TECWERK UID: 2000806617NW Facts Diameter: 12 mm Helix angle: 25° Flutes: 1 Shank: cylindrical (DIN 6535 HA) Design: long Cutting direction: right-hand Special features Solid carbide (VHM), ultra-fine grain Factory standard (Werksnorm) Very well suited for non‑ferrous metals Suitable for aluminium alloys up to 7% silicon Suitable for plastics Optimised for thin‑walled profiles FAQ What materials is this cutter suitable for? The Single‑flute cutter Type W Ø12 mm from TECWERK is designed for non‑ferrous metals and engineering plastics, and is suitable for aluminium alloys with up to 7% silicon. Why choose a single‑flute design for profiles? A single‑flute cutter such as this provides improved chip evacuation and lower radial forces, which helps maintain the shape of thin‑walled profiles during machining. Which shank standard does the tool use? The cutter is supplied with a cylindrical shank conforming to DIN 6535 HA, allowing secure clamping in compatible holders. Is the cutter suitable for long reach machining? Yes, the long design and stable cylindrical shank reduce vibration and support longer engagement lengths in profile milling operations. How does the 25° helix angle affect performance? The 25° helix promotes smooth cutting and efficient chip removal, reducing heat and improving surface finish when machining soft alloys and plastics. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a combination of solid carbide micrograin construction and a 25° helix for low cutting forces and clean chip evacuation; this long single-flute cutter is especially suited to thin-walled non-ferrous and plastic profiles. Order the tool through Metav Werkzeuge or consult the team for detailed machining advice. Single-flute end mill Type W, Ø 6 mm — TECWERK, 25° helix, solid carbide The Single-flute end mill Type W, Ø 6 mm is a long solid carbide cutter designed for precision machining of thin-walled profiles and components made from non-ferrous metals and engineering plastics. Solid carbide, fine-grain micrograin 25° helix for reduced cutting forces Long design with DIN 6535 HA shank Optimised for non-ferrous metals and plastics Clean cuts and minimal deformation for delicate components The combination of a single-flute geometry and a 25° helix reduces radial cutting forces and heat generation, which helps to avoid distortion on thin-walled parts. Manufactured from solid carbide in a fine-grain grade, the tool maintains cutting edge integrity and delivers consistent surface quality on delicate profiles. Its specification explicitly supports aluminium alloys up to 7% silicon, ensuring predictable behaviour when machining common light-metal alloys used in fabrication and extrusion work. Extended reach with secure clamping for profile machining This long version features a DIN 6535 HA cylindrical shank that provides a reliable clamping interface in standard toolholders, reducing runout and improving repeatability for deeper operations. The increased reach of the long version enables access to recessed features and complex profile shapes without compromising stability, which lowers the need for secondary operations and simplifies set-up sequences in jigs and fixtures. Efficient chip evacuation and reliable process stability The single cutting edge supports effective chip evacuation, particularly important when working with plastics or soft non-ferrous metals where chip packing can otherwise occur. Combined with the tool’s right-hand cutting geometry, this promotes uninterrupted cutting action and reduces the risk of built-up edge, resulting in fewer reworks and improved process uptime. The design therefore supports a smoother production flow and helps to maintain consistent cycle times in series work. Practical workshop benefits and integration into production Engineered for profile work and thin-walled components, the cutter’s fine-grain carbide composition offers wear resistance and a dependable tool life under appropriate machining conditions. The tool’s characteristics translate into lower scrap rates and less finishing work for assemblies where dimensional integrity matters. Supplied as a single unit, the cutter integrates well with standard collet systems and is practical for small-batch production as well as repetitive manufacturing tasks. For reliable, low-force profiling with the 25°-helix TECWERK single-flute cutter, contact Metav Werkzeuge for technical advice or to place an order at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: 2000806614NW Item designation: Single-flute end mill Type W, Ø 6 mm, solid carbide UID: 2000806614NW Facts Diameter: 6 mm Helix angle: 25° Number of cutting edges: 1 Cutting direction: right-hand Shank standard: DIN 6535 HA Packaging unit: 1 Materials / Special features Solid carbide (VHM), universal fine-grain Long design, cylindrical shank according to DIN 6535 HA Suitable for non-ferrous metals and plastics Suitable for aluminium alloys up to 7% silicon Right-hand cutting, optimised for thin-walled workpieces and profiles FAQ What materials is the cutter suitable for? The TECWERK single-flute end mill Type W is optimised for non-ferrous metals and plastics and is specified for aluminium alloys with up to 7% silicon. Is this tool appropriate for thin-walled profiles? Yes, the tool’s geometry and fine-grain solid carbide construction make the cutter well suited to machining thin-walled profiles with reduced risk of deformation. What shank standard does the tool use? The cutter is supplied with a cylindrical shank to DIN 6535 HA for secure clamping in standard holders. How many cutting edges does the tool have and which cutting direction is used? This is a single-cutting-edge tool (one flute) with right-hand cutting action for efficient chip removal. Is this the long version of the cutter and how is it supplied? The tool is the long variant and is supplied as a single unit suitable for applications requiring extended reach. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

VHM · Universal-Feinstkorn · Werksnorm · Typ W · lang · mit Zylinderschaft nach DIN 6535 HA · 25 ° Drallwinkel · rechtsschneidend · zur Bearbeitung von dünnwandigen Werkstücken, wie Bspw. Profilen, aus NE-Metallen und Kunststoffen, für Aluminium-Legierungen mit einem Siliziumgehalt bis 7 % Weitere technische Eigenschaften: · Werkstoffeignung NE-Metalle: sehr gut geeignet · Drallwinkel: 25°

VHM · Universal-Feinstkorn · Werksnorm · Typ W · lang · mit Zylinderschaft nach DIN 6535 HA · 25 ° Drallwinkel · rechtsschneidend · zur Bearbeitung von dünnwandigen Werkstücken, wie Bspw. Profilen, aus NE-Metallen und Kunststoffen, für Aluminium-Legierungen mit einem Siliziumgehalt bis 7 % Weitere technische Eigenschaften: · Werkstoffeignung NE-Metalle: sehr gut geeignet · Drallwinkel: 25°

VHM · Universal-Feinstkorn · Werksnorm · Typ W · lang · mit Zylinderschaft nach DIN 6535 HA · 25 ° Drallwinkel · rechtsschneidend · zur Bearbeitung von dünnwandigen Werkstücken, wie Bspw. Profilen, aus NE-Metallen und Kunststoffen, für Aluminium-Legierungen mit einem Siliziumgehalt bis 7 % Weitere technische Eigenschaften: · Werkstoffeignung NE-Metalle: sehr gut geeignet · Drallwinkel: 25°

VHM · Universal-Feinstkorn · Werksnorm · Typ W · lang · mit Zylinderschaft nach DIN 6535 HA · 25 ° Drallwinkel · rechtsschneidend · zur Bearbeitung von dünnwandigen Werkstücken, wie Bspw. Profilen, aus NE-Metallen und Kunststoffen, für Aluminium-Legierungen mit einem Siliziumgehalt bis 7 % Weitere technische Eigenschaften: · Werkstoffeignung NE-Metalle: sehr gut geeignet · Drallwinkel: 25°