10mm Precision Engraving Stiletto Profile A HSS-EW9Co10 ±2 mm, HRC 65-69 - Werner Wilke Zerspanungstechnik GmbH
Benefit from a combination of high tool hardness (65–69 HRC) and a 10% cobalt HSS alloy for sustained edge life and reliable engraving results; the precision-ground profile A geometry and tight tolerances ensure consistent copy-milling and lettering work. Order the tool directly via Metav Werkzeuge or consult the team for application-specific advice. Engraving cutter Pro A, 10 mm — HSS‑EW9Co10, 125 mm, Werner Wilke A Pro A engraving cutter in HSS‑EW9Co10 designed for precise lettering, contour engraving and copy milling with a straight cutting edge and industrial tolerances HSS‑EW9Co10 with 10% cobalt for heat resistance Hardness 65–69 HRC for durable cutting edge Precision-ground straight cutting edge Diameter tolerance h8, length tolerance ±2 mm Precise cutting performance for lettering and contours The Pro A engraving cutter delivers repeatable results where fine detail and a clean finish matter. Made from HSS‑EW9Co10, an alloyed high‑speed steel with 10% cobalt, the tool maintains hardness at elevated temperatures and supports longer intervals between regrinds. The precision-ground straight cutting edge reduces burr formation on thin strokes, which leads to cleaner letters and more accurate contour edges during copy milling. This stability translates into less manual finishing and a higher yield from each workpiece. Robust materials and heat-resistant construction for productivity A construction hardened to 65–69 HRC gives the tool a resilient cutting face, while the cobalt content enhances red hardness for demanding cycles. For shops running longer production sequences or intermittent higher spindle speeds, the material choice supports consistent performance. The combination of high hardness and alloy composition helps the cutter resist abrasion and deformation, preserving the critical geometry that defines engraving depth and profile accuracy. Tight tolerances and dimensions for reliable set‑up Dimensional control is essential in engraving operations; the cutter is available in a 10 mm diameter with a total length of 125 mm and a cutting length of 15 mm. Diameter tolerance h8 and length tolerance ±2 mm ensure predictable fit in collets and fixtures, minimising run‑out and alignment errors. The tool’s halfing is pre-ground to a specified value (+0.1 mm tolerance), supporting repeatable seating and concentricity during changeovers, which reduces set‑up time and scrap. Practical benefits for workshop workflows Engineered for engraving scripts, fine contours and copy milling, the cutter’s straight edge geometry simplifies toolpath planning and often permits single‑pass operations where complex shapes are required. The tool’s precision and material properties support longer tool life and fewer interruptions for dressing or replacement. For production floors aiming to reduce cycle time and manual touch‑ups, this cutter offers a balance between durability and the fine control necessary for high‑quality engraved components. Contact Metav Werkzeuge for an expert recommendation on the Werner Wilke Pro A engraving cutter and to discuss suitability for specific materials or machining strategies — Metav Werkzeuge can advise on fixtures, speeds and feeds for best results Technical data Article number: 4118430030NW Label: Gravierstichel Pro A D.10mm HSS‑EW9Co10 1.3207 Gesamt‑L.125mm WERNER WILKE SKU: 4118430030NW Facts Diameter: 10 mm Total length: 125 mm Cutting length: 15 mm Hardness: 65–69 HRC Cobalt content: 10% Diameter tolerance: h8 Length tolerance: ±2 mm Halfing tolerance: +0.1 Special features Material: HSS‑EW9Co10 (Werkstoff 1.3207) Profile: A Hardened, tempered and precision‑ground Straight cutting edge, halfing pre‑ground Dx1.5 Application: engraving of lettering and contours, copy milling Product type: Engraving cutter (Gravierstichel) Packaging unit: 1 Manufacturer: Werner Wilke Zerspanungstechnik GmbH FAQ What is the primary application for this tool? The engraving cutter Pro A is intended for precise engraving of letters and contours and for copy milling applications where a straight cutting edge is required. Which material is the cutter made from? The tool is made from HSS‑EW9Co10 (material number 1.3207) with 10% cobalt for improved red hardness and wear resistance. How does the hardness affect performance? A hardness of 65–69 HRC gives the tool a durable cutting edge that maintains geometry over extended use, reducing regrinding frequency in demanding engraving work. Are the dimensional tolerances suitable for collet mounting? Yes, the cutter has a diameter tolerance h8 and a length tolerance of ±2 mm, supporting consistent collet fit and concentric running in standard toolholders. Can this cutter be used for copy milling on delicate workpieces? The precision‑ground straight cutting edge and controlled tolerances make the cutter well suited to copy milling of fine details while minimising burrs and surface damage on delicate components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10mm Profile D Engraving Cutter Solid Carbide K10/K20, 60° Tip, h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid-carbide fine-grain K10/K20 construction, a precision-ground 60° tip and a tight h6 diameter tolerance for reliable engraving and contour copying; order the engraving cutter directly via Metav Werkzeuge or consult our technical advisers for application support. Engraving cutter Pro D Ø10 mm — Solid-carbide K10/K20, 60° tip (Werner Wilke) The Engraving cutter Pro D Ø10 mm is a precision-ground, solid-carbide engraving tool designed for lettering, contour work and copy milling across steel, cast iron, non-ferrous metals and engineering plastics. Solid carbide, fine-grain K10/K20 Precision-ground 60° sharp tip Diameter tolerance h6 for accurate fits Suitable for steel, cast iron and plastics Consistent detail and repeatability for production engraving Built from solid carbide fine-grain K10/K20, this engraving cutter delivers high stiffness and wear resistance that translate into consistent edge retention and predictable part quality. The 10 mm diameter with h6 tolerance ensures repeatable fits in fixtures and collets; when tight concentricity and dimensional stability matter, the defined tolerance reduces setup variation. The 60° tip produces crisp strokes for lettering and fine contours, while the 15 mm cutting length balances reach with rigidity. These attributes support stable CNC engraving cycles and reduce rework in high-mix, short-run production. Reduced tool change and dependable tool life in daily use The Pro D’s precision-ground geometry and fine-grain carbide minimise flank wear and chipping during extended runs, which lowers tooling expenditure through fewer replacements. The tool’s pre-ground half-edge speeds up first-use readiness and simplifies initial tuning on a machine, so setup time is shorter. Length tolerance of ±2 mm gives a clear expectation for tool stick-out in fixtures, aiding process planning and reducing downtime. For workshops seeking a robust, low-fuss engraving option, this tool offers measurable productivity improvements. Wide material compatibility for versatile machining tasks Where multi-material capability is required, this engraving cutter is specified for steel, grey cast iron, non-ferrous metals and plastics, enabling single-tool solutions for mixed batches or prototype work. The geometry is suitable for both freehand contouring and guided copy milling, producing legible lettering and fine profiles without excessive burr formation. The tool’s combination of cutting length, overall length (75 mm) and tip angle makes it well suited to tasks where detail and access coexist, such as nameplates, control-panel engraving and mould-text modifications. Practical guidance and commercial reliability from Metav For procurement and process integration, choose a supplier that stands by consistent quality: Metav combines broad product availability with practical support for industrial and workshop users. The Pro D variant is offered in single-piece packaging and is compatible with standard collet systems suited to its diameter tolerance. For specialised reconditioning or application-specific advice, Metav’s advisors can help identify downstream efficiencies and appropriate machining parameters to protect tool life and part quality. Contact Metav Werkzeuge today to discuss the Werner Wilke engraving cutter Pro D and receive tailored recommendations for fixture, speed and feed strategies directly from our technical advisers at Metav Werkzeuge. Technical data Article number: 4118440100NW Description: Engraving cutter Pro D Ø10 mm VHM overall length 75 mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Engraving cutter Form: Profil D Packaging unit: 1 Facts Diameter: 10 mm Overall length: 75 mm Cutting length: 15 mm Tip angle: 60° Diameter tolerance: h6 Length tolerance: +/- 2 mm SKU: 4118440100NW Special features Solid-carbide fine-grain K10/K20 Precision-ground geometry Profile D configuration Half-edge pre-ground for initial sharpness Suitable for steel, grey cast iron, non-ferrous metals and plastics Designed for engraving letters, contours and copy milling FAQ What materials can be machined with this engraving cutter? The engraving cutter Pro D Ø10 mm is specified for use on steel, grey cast iron, non‑ferrous metals and various plastics, making it suitable for mixed-material workshops. What does the h6 diameter tolerance mean for setup? An h6 tolerance on the 10 mm diameter ensures tight dimensional conformity for consistent clamping and concentricity when using collets or fixtures. Is the Pro D cutter ready for immediate use on the machine? The tool is precision-ground with a pre-ground half-edge, which facilitates quicker initial setup; final adjustments to feeds and speeds should be validated on the specific machine and workpiece. Can the cutter be used for copy milling as well as freehand engraving? Yes, the geometry and cutting length are intended for both lettering/contour engraving and guided copy milling where detail and repeatability are required. How is tool life improved compared with standard carbide tools? The fine-grain K10/K20 carbide and precision-ground tip minimise wear and chipping, providing longer effective tool life under comparable cutting conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Profile A Engraving Cutter D.8mm HSS-EW9Co10 10% Coated? No, Solid HSS, 65-69 HRC, h8 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Benefit from the combination of HSS-EW9Co10 construction, 65–69 HRC hardness and precision-ground geometry for consistent, long-lasting engraving performance; order the engraving cutter directly via Metav Werkzeuge or request technical advice from our consultants. Engraving cutter Pro A D.8 mm HSS-EW9Co10 by Werner Wilke – 8 mm diameter, 10% cobalt The Engraving cutter Pro A D.8 mm HSS-EW9Co10 is a hardened, precision-ground tool designed for engraving letters, fine contours and for copy milling in demanding workshop and production environments. HSS with 10% cobalt for heat resistance Hardened 65–69 HRC for durable edge retention Precision-ground Profile A, straight cutting edge Suitable for engraving and copy milling applications High hardness and cobalt alloy for sustained cutting performance The alloyed HSS-EW9Co10 formulation with 10% cobalt is engineered for elevated thermal stability and wear resistance. Combined with a hardness rating of 65–69 HRC, this specification reduces flank wear and preserves profile accuracy over extended runs. The result is consistent engraving depth and reduced tool changes in batch work, which supports predictable cycle times and lower tooling overhead in production. The material choice also improves resistance to softening at higher cutting temperatures, enabling more reliable processing of tougher workpiece materials. Precision geometry for clean, repeatable contours Profile geometry and edge preparation determine the quality of engraved letters and contours. The tool’s Profile A and straight cutting edge, delivered precision-ground, create sharp, well-defined grooves and crisp lettering. The tool includes a pre-ground halfing (Dx1.5) for reliable centring in copy-milling and engraving operations; diameter tolerance h8 and halfing tolerance +0.1 ensure reproducible positioning. These design elements translate directly into improved part quality and less rework when producing fine details or following templates. Practical dimensions and tolerances for workshop integration With an 8 mm diameter and an overall length of 125 mm, the cutter balances rigidity and accessibility for many common toolholders. A cutting length of 12 mm provides sufficient engagement for deeper engraving passes while maintaining strength at the tip. Length tolerance +/- 2 mm supports predictable tool set-up, helping to maintain consistent process parameters across tool changes. The combination of compact dimensions and robust construction makes the cutter suitable for both manual engraving fixtures and CNC copy-milling heads. Application focus and handling recommendations Designed specifically for engraving of scripts, fine contours and for copy milling, the tool is well suited to operations that demand geometric fidelity. The precision-ground finish and HSS-EW9Co10 composition favour performance on tougher workpiece surfaces where heat generation is a factor. For best results, use stable clamping and moderate feeds that allow the cobalt-steel matrix to dissipate heat; this approach prolongs edge life and maintains profile sharpness. Regular inspection of the cutting edge for chipping will help schedule regrinding before part quality is affected. For procurement or expert technical guidance on Werner Wilke HSS-EW9Co10 engraving cutters, contact Metav Werkzeuge for direct supply and application support Technical data Article number: 4118430025NW Product type: Engraving cutter Manufacturer: Werner Wilke Zerspanungstechnik GmbH Label: Gravierstichel Pro A D.8mm HSS-EW9Co10 1.3207 Gesamt-L.125mm WERNER WILKE Facts Diameter: 8 mm Overall length: 125 mm Cutting length: 12 mm Hardness: 65–69 HRC Diameter tolerance: h8 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 Cobalt content: 10% Werkstoffnummer: 1.3207 Special features Material: HSS-EW9Co10 Profile A Hardened, tempered and precision-ground Straight cutting edge, halfing pre-ground Dx1.5 Intended for engraving letters and contours Suitable for copy milling applications FAQ What materials is this cutter intended for? The engraving cutter Pro A D.8 mm HSS-EW9Co10 (SKU 4118430025NW) is designed for engraving letters, contours and copy milling; its cobalt-enriched HSS composition improves thermal stability on tougher workpiece materials. How does the 10% cobalt content affect tool life? A higher cobalt content in HSS-EW9Co10 increases heat resistance and hardness retention, so the Werner Wilke engraving cutter maintains a sharper profile for longer under elevated cutting temperatures. What tolerances can be expected from this tool? Diameter tolerance is h8, length tolerance is +/- 2 mm and halfing tolerance is +0.1, enabling consistent positioning and repeatable results when using jigs or copy-milling setups. Is the cutter suitable for copy milling on CNC machines? Yes; the precision-ground profile, straight cutting edge and pre-ground halfing make this cutter appropriate for copy milling tasks where faithful contour transfer is required. How should the cutting parameters be adapted for best results? Moderate feed rates and stable clamping are recommended so the HSS-EW9Co10 alloy can dissipate heat effectively; this approach preserves the 65–69 HRC edge hardness and reduces the risk of chipping. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Precision Engraving Tool Profil A HSS-EW9Co10 10% Co, HRC 65-69, ±2mm Length, h8 Diameter Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of high wear resistance and tight dimensional control for dependable engraving results; the combination of HSS-EW9Co10 construction, 65–69 HRC hardness and precision tolerances supports consistent production quality. Order directly via Metav Werkzeuge or consult their technical advisors for application-specific guidance. Pro A engraving cutter D12 mm, HSS-EW9Co10 – Werner Wilke The Pro A engraving cutter is a precision tool for fine lettering, contour engraving and copy milling in demanding workshop and industrial applications. 12 mm diameter solid HSS with 10% cobalt Hardened to 65–69 HRC for high wear resistance Precision-ground straight cutting edge for fine detail Suitable for engraving and copy milling applications Crisp lettering and accurate contours for repeatable results The Pro A engraving cutter delivers a predictable tool path thanks to its precision-ground geometry and straight cutting edge. Profile A is tailored for delicate letterforms and narrow contours, which reduces the need for corrective finishing. The tool's cutting length 18 mm and its diameter tolerance h8 maintain a stable engagement depth, helping to reproduce fine details consistently. When used in copy milling, the stable geometry minimises chatter and reduces the risk of dimensional drift, so repeat runs remain within expected tolerances. Material choice and heat-resistant cutting for longer tool life Manufactured from HSS-EW9Co10 with a 10% cobalt content and heat-treated to 65–69 HRC, this engraving cutter balances hardness with red-hardness for improved wear resistance under elevated temperatures. The higher cobalt proportion increases performance on tougher workpiece materials and extends life compared with standard high-speed steels. The hardened, tempered and precision-ground finish further reduces flank wear and preserves the cutting edge, which cuts downtime and frequency of tool changes in batch operations. Dimensional control and mounting stability for secure machining A 12 mm shank diameter and total length 160 mm provide a practical reach while remaining compatible with common collet and chuck systems. Length tolerances of ±2 mm and a halfing tolerance of +0.1 ensure predictable clamping and concentricity when setting up fixtures. These dimensional controls support stable tool run-out and improve surface quality on engraved features. The combination of tight diameter tolerance and a pre-ground halfing (Dx1.5) simplifies centring and makes the tool suitable for both manual and automated engraving fixtures. Practical benefits for shop-floor applications The tool is designed for efficient integration into production: hardened construction and precision grinding reduce finishing work and extend intervals between regrinds, while the straight cutting edge provides clear, sharp grooves in lettering and contours. The material specification (Werkstoff 1.3207) and manufacturing tolerances make the cutter a reliable choice for small-series runs and repeat jobs where consistency matters. For specific material applications or fixturing questions, Metav Werkzeuge’s technical team can provide targeted advice to align the tool to the machining process. For application advice, reliable supply and a workshop-oriented selection process, contact Metav Werkzeuge for a tailored recommendation and secure delivery from Emmerich. Technical data SKU: 4118430040NW Product type: Engraving cutter Material: HSS-EW9Co10 Diameter: 12 mm Total length: 160 mm Hardness: 65–69 HRC Dimensions & tolerances Cutting length: 18 mm Diameter tolerance: h8 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 Cutting edge: straight (halfing pre-ground Dx1.5) Features Profile A Werkstoff 1.3207 10% cobalt content Hardened, tempered and precision-ground Suitable for engraving of lettering and contours and for copy milling FAQ What materials can this engraving cutter machine best? The Pro A engraving cutter (Werner Wilke engraving cutter, SKU 4118430040NW) is suited to a broad range of materials that are commonly engraved, benefitting from the HSS-EW9Co10 composition and higher cobalt content for improved wear resistance. How does the hardness rating affect performance? A hardness of 65–69 HRC increases edge retention and resistance to abrasive wear; the Werner Wilke Pro A engraving cutter maintains sharper geometry for longer, reducing finishing effort. Which tolerances are most relevant for setup? Diameter tolerance h8, length tolerance ±2 mm and halfing tolerance +0.1 are the critical dimensions for secure clamping and concentricity during engraving and copy milling operations. Is the tool suitable for automated copy milling? Yes, the precision-ground geometry and tight tolerances of the engraving cutter support stable operation in both manual and automated copy milling setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Profile A Engraving Stylus HSS-EW9Co10 10% Cobalt Hardened 65-69 HRC, h8 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a wear-resistant HSS‑EW9Co10 body with 10% cobalt and a high hardness of 65–69 HRC for stable edge life and reproducible engraving results; order the engraving cutter directly via Metav Werkzeuge or ask our consultants if needed Engraving cutter Pro A Ø12 mm, HSS‑EW9Co10 – Werner Wilke, hardened precision cutter, Ø12 mm, L 125 mm The Engraving cutter Pro A Ø12 mm HSS‑EW9Co10 is a precision tool for engraving letters, contours and for copy milling, featuring a straight cutting edge and pre-ground halving for reliable centring HSS‑EW9Co10 with 10% cobalt Hardened to 65–69 HRC Diameter tolerance h8 Precision-ground straight cutting edge Long-lasting cutting performance from high-speed steel with cobalt The use of HSS‑EW9Co10 (Werkstoff 1.3207) with a 10% cobalt content provides enhanced red-hardness and wear resistance compared with standard high-speed steels; this translates into longer tool life under sustained loads and higher cutting temperatures, which reduces the need for frequent replacements and supports stable batch production. The combination of a hardened substrate and a precision grind ensures a consistently sharp profile for fine detail work, keeping downtimes low and throughput predictable. Precision tolerances for repeatable engraving results A strict diameter tolerance h8 and a length tolerance of ±2 mm guarantee that tool dimensions remain within close limits, improving part-to-part consistency on CNC engraving machines. The halfing tolerance +0.1 mm and the pre-ground halving (D×1.5) support accurate positioning in fixtures and minimise runout, so patterns and lettering retain uniform depth and legibility across multiple components. These measurable tolerances are particularly relevant for production runs that demand traceable accuracy. Designed for engraving letters, contours and copy milling The straight cutting edge and a cutting length of 18 mm make this profile ideal for crisp lettering and fine contour work, while the overall length of 125 mm provides sufficient reach for most engraving and copying operations. The tool is suitable for use with standard toolholders and fixtures used in workshop and light industrial settings, enabling straightforward integration into existing CNC setups without complex adaptation. Practical workshop benefits and application guidance Hardened to 65–69 HRC and precision-ground, this cutter offers robustness when working on a range of materials commonly encountered in engraving tasks. The specification emphasises controlled performance rather than experimental coatings, so process parameters such as feed and spindle speed should be set with the material and cutter geometry in mind. For application-specific recommendations or to confirm compatibility with a particular workpiece material, technical consultation is available to match the tool’s profile and tolerances to the machining task. For tailored advice on Werner Wilke engraving cutters, contact Metav Werkzeuge GmbH in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for recommendations on profile selection and tolerance requirements Technical data Article number: 4118430035NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Engraving cutter (Profile A) Material designation: HSS‑EW9Co10 (Werkstoff 1.3207) Core data Diameter: 12 mm Overall length: 125 mm Cutting length: 18 mm Hardness: 65–69 HRC Diameter tolerance: h8 Length tolerance: ±2 mm Halfing tolerance: +0.1 mm Cobalt content: 10% Packaging unit: 1 piece Special features Straight cutting edge, halfing pre-ground (D×1.5) Hardened, tempered and precision ground For engraving letters, contours and copy milling Diameter tolerance h8 and length tolerance ±2 mm FAQ Which materials is this cutter suitable for? The engraving cutter Pro A (Werner Wilke, SKU 4118430035NW) is specified for precision engraving and copy milling; material suitability depends on machining parameters and workpiece hardness given the tool’s 65–69 HRC substrate. What does HSS‑EW9Co10 mean for tool behaviour? HSS‑EW9Co10 indicates a high‑speed steel grade with elevated cobalt content (10%), providing improved red‑hardness and wear resistance compared with ordinary HSS, which benefits sustained engraving operations. How precise are the dimensions of the cutter? The tool is manufactured to diameter tolerance h8 with a length tolerance of ±2 mm and a halfing tolerance of +0.1 mm, supporting consistent positioning and repeatable engraving results. Can this cutter be used for copy milling on CNC machines? Yes; the Pro A profile with a straight cutting edge and cutting length 18 mm is intended for engraving and copy milling tasks and is compatible with common CNC engraving setups. Is the halving pre-ground and what is Dx1.5? The halfing is pre-ground to aid accurate centring; the notation D×1.5 refers to the preparation of the halving diameter relative to the cutter for correct seating in fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Profile A Solid Carbide Engraving Cutter Precision Ground, h6 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Benefit from the combination of solid carbide fine-grain K10/K20, a precision-ground Profile A geometry and a straight cutting edge that is pre-ground for reliable centring; ideal for clean engraving of letters and contours across steel, cast iron, non‑ferrous metals and plastics — order directly via Metav Werkzeuge or consult our specialists for application advice. Engraving cutter Pro A — 12 mm, solid carbide, 75 mm overall (Werner Wilke) The Engraving cutter Pro A is a precision-ground, solid-carbide engraving tool designed for fine lettering, contour work and copy milling across a wide range of common workshop materials. Solid carbide fine-grain K10/K20 Precision-ground Profile A geometry Straight cutting edge, pre-ground centre Suitable for steel, cast iron and plastics Precision geometry that reduces finishing work The tool’s solid carbide construction in fine-grain K10/K20 delivers a consistently hard cutting edge and predictable wear characteristics. The precision-ground Profile A shape and the straight cutting edge (with the centre halfing pre-ground) produce crisp, repeatable cuts that minimise burr formation and reduce secondary finishing. For production environments where time and quality are decisive, the combination of material and grinding quality means fewer rejected parts and lower rework costs per batch. Broad material compatibility for versatile use Engineered for common workshop applications, the cutter is suitable for steel, grey cast iron, non‑ferrous metals and plastics, enabling a single tool to cover engraving, contouring and copy milling tasks. The tool’s cutting length and geometry make it appropriate for delicate lettering and precise contour transfers from templates, while its carbide substrate maintains edge integrity when switching between metals and polymers. This versatility supports streamlined tooling inventories and faster process changeovers. Defined tolerances for consistent set-up and repeatability Manufactured to tight dimensional standards, the cutter has a diameter tolerance h6, a length tolerance of ±2 mm and a halfing tolerance of +0.1, with a cutting length of 12 mm. These specified tolerances enable reliable tool offsets, predictable runout behaviour and repeatable results across setups. For CNC and manual operations where repeatability is essential, such defined tolerances reduce trial runs and simplify quality control, contributing to shorter lead times and stable production output. Workshop integration and handling advantages Delivered as a single-piece item in a pack quantity of one, the tool’s pre-ground halfing and straight-edge finish shorten initial tool preparation and improve mounting accuracy. The fine-grain carbide composition supports sustained cutting performance under normal workshop feeds and speeds, extending service intervals. For system planners and maintenance teams, the cutter’s consistent geometry and material choice ease tool management and inventory planning while supporting predictable process windows. Contact Metav Werkzeuge for sourcing the Pro A solid‑carbide engraving cutter and for tailored technical guidance — telephone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss application details and supply options Technical data Article number: 4118440050NW Product: Engraving cutter (Profile A) Manufacturer: Werner Wilke Zerspanungstechnik GmbH SKU: 4118440050NW Data Diameter: 12 mm Overall length: 75 mm Cutting length: 12 mm Diameter tolerance: h6 Length tolerance: ±2 mm Halfing tolerance: +0.1 Packaging unit: 1 Special features Solid carbide, fine-grain K10/K20 Precision-ground Profile A geometry Straight cutting edge, halfing pre-ground Suitable for steel, grey cast iron, non‑ferrous metals and plastics Designed for engraving letters, contours and copy milling FAQ What materials can be machined with this engraving cutter? The engraving cutter Pro A is suitable for steel, grey cast iron, non‑ferrous metals and plastics, as specified for general engraving and copy-milling applications. How precise are the tool dimensions and what tolerances apply? Dimensional control is specified: diameter tolerance h6, length tolerance ±2 mm and halfing tolerance +0.1, ensuring consistent setup and repeatable machining. Is the cutting edge ready for immediate use after unpacking? The tool features a straight cutting edge with the centre halfing pre-ground, which reduces initial preparation time before mounting in the spindle. Which grade of carbide is used and what advantage does it offer? The cutter is made from solid carbide fine-grain K10/K20, providing a hard, wear-resistant edge and stable performance across mixed-material tasks. What machining tasks is this cutter primarily intended for? It is designed for precise engraving of lettering and contours and for copy milling operations where accurate profile transfer is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Profile D Engraving Cutter Solid Carbide K10/K20, Precision Ground 60° Tip, h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a combination of solid‑carbide construction and precision‑ground geometry for consistent engraving results and reduced setup time; order directly via Metav Werkzeuge or consult our experts for application-specific guidance. Engraving cutter Pro D — 12 mm solid‑carbide, Profile D, 60° tip (Werner Wilke) The engraving cutter Pro D 12 mm is a solid‑carbide tool for precision lettering, contour engraving and copy milling across steel, grey cast iron, non‑ferrous metals and plastics Solid‑carbide, fine‑grain K10/K20 60° cutting edge, pre‑ground half tip For steel, cast iron, non‑ferrous metals, plastics Precision geometry that lowers rework and downtime The tool’s solid‑carbide composition in fine‑grain K10/K20 provides a stable cutting edge and uniform wear behaviour, which translates into fewer tool changes and less rework. The precision‑ground profile ensures repeatable results when producing small lettering and fine contours, while the h6 diameter tolerance maintains concentricity in tool holders and collets. By relying on dimensional stability rather than frequent recalibration, production flow remains predictable and efficient. Reliable cutting performance across common workshop materials Designed for a wide range of applications, the cutter handles steel, grey cast iron, non‑ferrous metals and plastics without the need for multiple specialised tools. The 60° cutting edge with a pre‑ground half tip improves penetration and centring for engraving and copy milling, while the 18 mm cutting length and 75 mm overall length balance reach and rigidity. This combination supports higher feed rates with consistent surface finish, delivering a measurable performance advantage in repetitive marking and contouring tasks. Practical tolerances and setup advantages for everyday use Diameter stability at 12 mm and a length tolerance of +/- 2 mm simplify tool management and inventory planning. The pre‑sharpened tip reduces setup time and minimises trial cuts, making the tool suitable for small batches as well as serial production. The cutter’s profile D geometry is optimised for clear, legible engraving and precise contour transfer during copy milling, so programming effort and downstream finishing can be reduced—supporting faster throughput and lower per‑part costs. Request technical advice or a tailored quotation from Metav Werkzeuge—contact the Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 for Werner Wilke solid‑carbide engraving cutters. Technical data Article number: 4118440105NW Product type: Engraving cutter Form: Profile D Manufacturer: Werner Wilke Zerspanungstechnik GmbH Dimensions & tolerances Diameter: 12 mm Overall length: 75 mm Cutting length: 18 mm Diameter tolerance: h6 Length tolerance: +/- 2 mm Tip angle: 60° Materials & applications Material: solid‑carbide, fine‑grain K10/K20 Applications: engraving of lettering and contours, copy milling Suitable for: steel, grey cast iron, non‑ferrous metals, plastics Packaging unit: 1 FAQ What materials can be machined with this engraving cutter? The engraving cutter Pro D (Werner Wilke) is suitable for steel, grey cast iron, non‑ferrous metals and plastics, making it versatile for marking and contour work. What does the 60° tip mean for engraving quality? A 60° cutting edge produces sharp, well‑defined grooves for lettering and fine contours; the pre‑ground half tip improves centring for accurate copy milling with the Werner Wilke engraving cutter. How precise is the tool diameter and length? Diameter tolerance is h6 and length tolerance is +/- 2 mm, ensuring consistent fit in collets and predictable axial position during machining. Is the cutter suitable for copy milling applications? Yes, the tool’s precision‑ground profile and stable solid‑carbide substrate make it well suited for copy milling tasks where accurate contour transfer and repeatability are required. What cutting length and overall reach does the tool offer? The cutter provides an 18 mm cutting length with a 75 mm overall length, offering a practical balance of reach and rigidity for engraving and contour work. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Precision Engraving Graver Pro A D6mm HSS-EW9Co10, Hardened 65-69 HRC - Werner Wilke Zerspanungstechnik GmbH
Benefit from long tool life and high cutting accuracy in engraving and copy milling tasks; the hardened and precision-ground design ensures consistent contour reproduction. Order the tool directly via Metav Werkzeuge or consult our specialists for process-matching recommendations. Engraving graver Pro A, 6 mm (HSS-EW9Co10) – straight cutting edge, hardened and precision ground, Werner Wilke An engraving graver Pro A, 6 mm designed for precision lettering, contour work and copy milling in demanding metalworking and toolroom applications. HSS with 10% cobalt for improved toughness Hardness 65–69 HRC for excellent wear resistance Precision ground Profile A with straight cutting edge Diameter tolerance h8 and length tolerance +/- 2 mm Precise results through a hardened, cobalt-alloy construction The tool is made from HSS-EW9Co10 (material number 1.3207) with a 10% cobalt content, a composition that raises red hardness and edge stability under thermal stress. Combined with a hardness of 65–69 HRC, the graver delivers consistent cutting geometry over longer runs, reducing the need for frequent tool changes and ensuring steady results when producing fine lettering or detailed contours. This composition is particularly suited to applications where heat and abrasion challenge standard high-speed steels. Reproducible contours and process efficiency in production Thanks to the precision-ground Profile A and a straight cutting edge with pre-ground centring (Dx1.5), the graver enables accurate contour following and reliable copy milling performance. The 6 mm diameter and 9 mm cutting length provide a compact geometry that balances stiffness and accessibility for narrow contours. Tight tolerances—diameter h8 and length +/- 2 mm—support predictable fixture set-up and reproducible part quality, which in turn improves throughput and reduces scrap in series production. Practical handling, sharpening and workshop integration The component is delivered hardened, tempered and precision ground, making it ready for immediate use in standard toolholders suitable for engraving cutters. The tool’s surface and geometry allow controlled regrinding where necessary; however, the elevated hardness requires appropriate grinding equipment and cooling strategies to preserve the cutting edge. For everyday workshop workflows, the graver’s compact overall length of 80 mm and single-piece design simplify clamping and inspection, while the halfing tolerance +0.1 and pre-ground halfing help achieve consistent centring for replicable results. Choose the Werner Wilke engraving graver for reliable engraving and copy milling performance—contact Metav Werkzeuge for application advice or procurement via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118430015NW Label: Gravierstichel Pro A D.6mm HSS-EW9Co10 1.3207 Gesamt-L.80mm WERNER WILKE Product: Engraving graver Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: HSS-EW9Co10 Facts Diameter: 6 mm Overall length: 80 mm Cutting length: 9 mm Hardness: 65–69 HRC Cobalt content: 10% Diameter tolerance: h8 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 Special features Profile A Material number: 1.3207 Hardened, tempered and precision ground Straight cutting edge, pre-ground centring Dx1.5 For engraving letters and contours and copy milling Packing unit: 1 FAQ What is the primary application of this tool? The Werner Wilke engraving graver Pro A (SKU 4118430015NW) is intended for engraving letters and contours and for copy milling where fine, reproducible details are required. Which material and alloy are used for the tool? The tool is manufactured from HSS-EW9Co10 (material number 1.3207) and contains 10% cobalt, providing improved red hardness and edge retention. What tolerances can be expected from the graver? Key tolerances are diameter h8, length +/- 2 mm and halfing tolerance +0.1, supporting predictable set-up and repeatable results. Is regrinding feasible given the hardness? Regrinding is technically possible; the item is hardened and precision ground to 65–69 HRC, so sharpening requires suitable grinding equipment and careful heat control to maintain edge geometry. Can the graver be used for copy milling in series production? Yes. The precision-ground profile and stable alloy composition are designed to support consistent reproduction in copy milling applications. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2mm Profile D Precision Engraving Cutter 40mm Overall Length, 60° Tip, h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the solid-carbide K10/K20 construction and the 60° precision-ground tip for durable, repeatable engraving of lettering and contours; order the engraving cutter directly via Metav Werkzeuge or consult the team for application advice. Engraving cutter Pro D, Ø2 mm (solid carbide, 60° tip) — Werner Wilke The Engraving cutter Pro D is a precision-ground solid‑carbide engraving tool designed for fine lettering, contour work and copy milling across steel, grey cast iron, non‑ferrous metals and plastics. Solid-carbide fine-grain K10/K20 60° precision-ground tip Ø2 mm with h6 diameter tolerance Suitable for steel, cast iron & plastics High-precision carbide for consistent engraving results Manufactured from solid carbide in fine‑grain K10/K20, this cutter delivers long tool life and stable edge retention under repetitive use. The fine‑grain microstructure reduces chipping and provides consistent cutting geometry, which translates into fewer tool changes and steady part quality. For production environments where repeatability matters, the precision-ground geometry reduces variation between tools and supports reliable machining cycles. Sharp 60° tip for crisp lettering and contours The 60° tip is engineered for crisp, narrow grooves and detailed engraving of characters and fine shapes. With a 3 mm cutting length, the geometry is optimised for shallow contouring and accurate depth control during copy milling operations. The pre‑sharpened edge (halfing pre-ground) shortens setup time and helps achieve clean edges on small radii without extensive finishing passes. Versatile across common engineering materials This cutter is specified for machining steel, grey cast iron, non‑ferrous metals and plastics, offering a single‑tool option for mixed‑material shops. The combination of material grade and tip geometry supports both manual and CNC engraving tasks where fine detail and surface integrity are required. When machining polymers or softer alloys, the fine‑grain carbide maintains form and reduces built‑up edge, improving surface finish on delicate features. Accurate tolerances for predictable setups With a nominal Ø2 mm shank and diameter tolerance h6, plus an overall length of 40 mm and length tolerance ±2 mm, the cutter enables reproducible tool offsets and reliable collet clamping. The specified tolerances simplify presetting and reduce time spent on trial cuts, supporting efficient fixture adjustments and faster first‑part approval in production workflows. The compact overall length also aids access to confined features during copy milling. Practical benefits for workshop efficiency By combining durable carbide, a defined tip angle and tight tolerances, the tool reduces downtime associated with frequent replacements and rework. The tool is particularly well suited to tasks that demand fine resolution—such as nameplates, control panel legends and precision mould markings—where legibility and edge quality are essential. Fewer finishing operations are required, which can lower cycle times and improve throughput for small detailed components. Contact Metav Werkzeuge for tailored technical advice on integrating the Werner Wilke engraving cutter Pro D into production and to secure stock for your workshop Technical data Article number: 4118440060NW Product type: Engraving cutter Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: Solid carbide, fine‑grain K10/K20 Profile: D Facts Diameter: Ø2 mm Overall length: 40 mm Cutting length: 3 mm Tip angle: 60° Diameter tolerance: h6 Length tolerance: ±2 mm Special features Precision-ground geometry Pre-sharpened 60° cutting edge (halfing pre-ground) For engraving lettering, contours and copy milling Suitable for steel, grey cast iron, non‑ferrous metals and plastics Packaging unit: 1 FAQ Which materials can this engraving cutter machine effectively? The engraving cutter Pro D from Werner Wilke is suitable for steel, grey cast iron, non‑ferrous metals and plastics, making it versatile for mixed‑material workshops. What tolerances ensure accurate presetting? Diameter tolerance h6 and a length tolerance of ±2 mm provide predictable offsets and reliable collet clamping for precise setups. What feature makes the cutter suitable for fine lettering? The 60° precision‑ground tip and 3 mm cutting length deliver the narrow grooves and crisp edges required for detailed lettering and contours. Is the tool ready to use or does it require additional sharpening? The cutter arrives with a pre‑sharpened cutting edge (halfing pre‑ground), reducing initial setup time and allowing immediate use for detailed engraving tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Engraving Cutter Profile A Solid Carbide K10/K20 Precision Ground +0.1mm Halfing Tolerance, h6 Diameter ±2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the tool's combination of solid carbide construction, precision-ground Profile A geometry and tight tolerances to achieve consistent engraving and copy milling results; order directly via Metav Werkzeuge or consult our specialists for application advice. Engraving cutter 'Pro A' — 3 mm solid carbide, 40 mm overall length (Werner Wilke) The Engraving cutter 'Pro A' is a Profile A engraving tool designed for precise lettering, contouring and copy milling across steel, cast iron, non-ferrous metals and plastics. Solid carbide, fine-grain K10/K20 Precision-ground Profile A geometry Diameter tolerance h6 for repeatable fits Suitable for steel, cast iron and plastics Consistent cut quality for repeatable engraving The engraving tool delivers a repeatable cut thanks to its solid carbide composition and precision-ground Profile A geometry. The combination of fine-grain K10/K20 carbide and a straight cutting edge ensures stable chip control and predictable wear patterns, which reduces setup time and scrap. With a 3 mm cutting diameter and a diameter tolerance h6, the cutter provides consistent results when producing detailed lettering or intricate contours, supporting reliable process planning in batch and single-part production. Broad material compatibility reduces tool changes Built for versatility, the tool is suitable for steel, cast iron, non-ferrous metals and plastics, enabling a single cutter to cover a wide range of engraving and copy-milling tasks. The tool’s geometry and material selection make it possible to achieve clean edges on metals while maintaining surface integrity on softer substrates. This reduces the need for multiple specialised cutters and supports more efficient tooling strategies on CNC engraving machines or manual copy-milling setups. Durability and handling that support productivity Durability is enhanced by the fine-grain carbide and the pre-finished cutting geometry, which together improve resistance to chipping and abrasion. The modest overall length of 40 mm overall length helps to minimise deflection in light-duty holders and contributes to accurate depth control when working close to tolerances. Tight length and diameter tolerances aid in predictable tool offsets, so operators and CAM programmers can maintain machining consistency and shorten qualification cycles. For reliable supply and application support of this engraving cutter, contact Metav Werkzeuge for advice and procurement — Metav’s specialists provide practical guidance from their Emmerich base to ensure the tool matches the process requirements. Technical data Article number: 4118440015NW Product type: Engraving cutter Label: Gravierstichel Pro A D.3mm VHM Gesamt-L.40mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Dimensions & tolerances Diameter: 3 mm Overall length: 40 mm Cutting length: 3 mm Diameter tolerance: h6 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 mm Materials & special features Material: solid carbide, fine-grain K10/K20 Profile: Profile A, precision-ground Cutting edge: straight cutting edge, pre-sharpened centre cut Applications: steel, cast iron, non-ferrous metals, plastics Packaging unit: 1 FAQ What materials can this engraving cutter machine? The engraving cutter 'Pro A' (engraving cutter, SKU 4118440015NW) is specified for use on steel, cast iron, non-ferrous metals and plastics. What tolerance can be expected for the diameter? Diameter tolerance is specified as h6, ensuring consistent fits for applications that require precise tool registers. How long is the tool and what is the cutting length? The overall length is 40 mm and the cutting length is 3 mm, suitable for shallow engraving and fine contour work. Is the cutting edge pre-finished for immediate use? Yes, the tool features a precision-ground straight cutting edge with a pre-sharpened centre cut to reduce initial dressing and setup time. Which material grade is the cutter made from? Manufactured from solid carbide in fine-grain K10/K20, the cutter balances hardness and toughness for engraving tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Profile D Engraving Cutter Solid Carbide K10/K20, 60° Tip, h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of precise engraving results thanks to solid carbide fine-grain K10/K20 and a 60° sharp tip, which together ensure repeatable lettering and contour milling; order through Metav Werkzeuge or request consultancy for application-specific data. Engraving cutter Pro D 3 mm – Solid carbide (Werner Wilke) Engraving cutter Pro D 3 mm is a precision solid carbide engraving tool for fine lettering, contours and copy milling across steel, cast iron, non‑ferrous metals and plastics. Solid carbide fine-grain K10/K20 60° sharp cutting tip Precision-ground, profile D geometry Suitable for steel, cast iron and plastics Consistent production through high-performance carbide The combination of solid carbide in fine-grain K10/K20 and a precision-ground profile delivers a tool that resists micro‑chipping and maintains geometry under continuous use. This construction enables stable troughs and crisp edges when engraving letters and contours, reducing the need for repeated rework. The tool’s design supports copy milling workflows where repeatability and surface quality directly influence downstream processes. Tight tolerances for predictable results Manufactured with a diameter tolerance h6 and a length tolerance of +/- 2 mm, the cutter offers dimensional reliability that simplifies process set-up. The h6 tolerance corresponds to an established shaft tolerance class, ensuring a consistent fit in collets and reduced concentricity errors. Such predictability shortens calibration time and supports CNC programmes that depend on exact tool dimensions for accurate path compensation. Broad material compatibility with clean finishes Engineered for use on steel, grey cast iron, non‑ferrous metals and plastics, the tool’s 60° tip and 4.5 mm cutting length provide a balance between penetration and control. For engraving thin scripts or fine contours the sharper tip delivers high definition, while the robust carbide grade copes with mixed‑material batches. The application spectrum covers detailed signage, serialisation, tool marking and pattern copying, where legibility and edge quality are paramount. Practical workshop advantages and handling With a 3 mm diameter and an overall length of 40 mm, the compact geometry supports tight toolpacks and fast index changes. The cutter arrives precision-ground with the tip half pre‑finished, which eases initial break‑in and stabilises edge formation during first cuts. Supplied as single units, the tool fits established collet systems and reduces inventory complexity for small‑batch and high‑mix operations. Operational benefits include fewer tool replacements and predictable wear characteristics that support cost‑effective production planning. For tailored advice on integrating the Werner Wilke engraving cutter into existing CNC or engraving workflows, contact Metav Werkzeuge for technical consultation and secure supply directly from Emmerich. Technical data Article number: 4118440070NW Product type: Engraving cutter Manufacturer: Werner Wilke Zerspanungstechnik GmbH Profile: D Packaging unit: 1 Facts Diameter: 3 mm Cutting length: 4.5 mm Overall length: 40 mm Tip angle: 60° Length tolerance: +/- 2 mm Diameter tolerance: h6 Special features Material: solid carbide, fine-grain K10/K20 Precision-ground geometry Half pre-ground cutting edge Suitable for steel, grey cast iron, non‑ferrous metals and plastics Intended for engraving of lettering, contours and copy milling FAQ What materials can be processed with this cutter? The engraving cutter is suitable for steel, grey cast iron, non‑ferrous metals and plastics, as stated in the product specifications. What is the tip angle and why does it matter? A 60° tip angle provides fine detail and sharp edges for lettering and contour work, improving definition in engraving and copy milling applications. How precise is the tool diameter? Diameter precision is delivered to h6 tolerance, ensuring consistent fit in collets and reliable repeatability for CNC programmes. Is the cutter ready to use straight from the package? The tool is precision-ground and supplied with the tip half pre‑finished, which eases initial break‑in; however, machine‑specific test cuts are recommended to verify optimal feed and speed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm Profile A Solid Carbide Engraving Cutter 2mm Diameter, Precision Ground h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid carbide fine-grain K10/K20, a 2 mm diameter for fine detail and precision-ground geometry to ensure consistent engraving results; order directly via Metav Werkzeuge or consult our specialists for application advice. Gravierstichel Pro A D.2mm — engraving cutter, solid carbide, precision-ground Gravierstichel Pro A D.2mm is a compact engraving cutter designed for fine lettering, contour work and copy milling across a range of engineering materials Solid carbide, fine-grain K10/K20 Precision-ground with straight cutting edge Ideal for steel, cast iron, non‑ferrous metals, plastics Diameter tolerance h6, length tolerance ±2 mm Precise geometry for repeatable engraving results The tool’s precision-ground profile delivers consistent geometry along the flute, which translates into uniform cuts and predictable tool life. Manufactured from solid carbide (fine-grain K10/K20), the shank and cutting portion maintain rigidity at small diameters, reducing chatter during high-precision engraving operations. For workshop planners this means fewer rejects and less rework when producing small lettering or intricate contours. Reliable performance across common workshop materials Thanks to the carbide grade and the straight cutting edge that is halfing pre-sharpened, the cutter is suitable for machining steel, grey cast iron, non‑ferrous metals and plastics. The balanced combination of material and cutter geometry enables clean edges when producing letters and delicate outlines, and supports light copy‑milling tasks where detail fidelity is essential. This tool therefore bridges the gap between hobby engraving and professional small‑part detailing. Dimensional control that supports automated processes With a nominal diameter of 2 mm, a 3 mm cutting length and a strict h6 diameter tolerance plus ±2 mm overall length tolerance, the cutter is engineered for predictable integration into CNC and manual engraving setups. Consistent dimensions reduce setup time and permit tighter process windows on automated equipment. The small halving tolerance of +0.1 mm on the pre-sharpened centreline also simplifies tool change calibration and repeatability in production runs. Practical advantages for procurement and daily use The compact overall length of 40 mm and the small diameter make the tool easy to handle and store while offering high local stiffness for fine detail work. Being precision-ground and produced from a fine-grain carbide reduces the need for frequent re‑grinding in light-duty applications, translating into lower operating interruptions. For workshop managers seeking dependable engraving performance, the cutter represents a technically sound choice that aligns with routine manufacturing workflows. For specialist advice on integrating the Pro A 2 mm engraving cutter into production or to request current availability, contact Metav Werkzeuge — our advisors can provide application guidance by phone or email. Technical Data Article number / SKU: 4118440005NW Label: Gravierstichel Pro A D.2mm VHM Gesamt-L.40mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: engraving cutter Profile: Profil A Facts Diameter: 2 mm Overall length: 40 mm Cutting length: 3 mm Diameter tolerance: h6 Length tolerance: ±2 mm Halving tolerance: +0.1 mm Special features Solid carbide, fine-grain K10/K20 Precision-ground, straight cutting edge Pre-sharpened halving Suitable for steel, grey cast iron, non‑ferrous metals, plastics Application: engraving letters and contours, copy milling FAQ What materials can this engraving cutter machine reliably? The Gravierstichel Pro A D.2mm engraving cutter machines steel, grey cast iron, non‑ferrous metals and plastics thanks to its solid carbide K10/K20 composition and precision-ground geometry. Is the cutter suitable for CNC copy milling of small parts? Yes. The cutter’s tight h6 diameter tolerance, stable 40 mm overall length and 3 mm cutting edge make it suitable for CNC copy milling where fine detail and repeatability are required. How precise are the length and diameter tolerances? Diameter tolerance is h6, overall length tolerance is ±2 mm and the halving tolerance is +0.1 mm, providing reliable dimensional control for automated and manual processes. Does the tool come ready for engraving or is additional sharpening required? The tool is delivered precision-ground with a straight cutting edge and a pre-sharpened halving, ready for immediate engraving and contour work. What typical applications is this cutter optimised for? Optimised for engraving letters, fine contours and light copy milling tasks in workshops and small-batch production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4mm Engraving Bur Profile A HSS-EW9Co10 10% Co Hardened Precision Ground +/-2mm, h8 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of durable HSS-EW9Co10 construction, precise h8 diameter tolerance and a pre-sharpened straight cutting edge for reliable, repeatable engraving and copy milling; order the tool through Metav Werkzeuge or consult the team for technical details and supply options. Pro A engraving cutter, D 4 mm – HSS‑EW9Co10, 63 mm overall length (Werner Wilke) The Pro A engraving cutter for precision engraving of lettering and contours and for copy milling in industrial workshops and toolrooms. HSS-EW9Co10 with 10% cobalt Hardness 65–69 HRC for long tool life Straight cutting edge, pre-sharpened halving Diameter 4 mm, tolerance h8, overall length 63 mm Higher uptime through harder, wear‑resistant steel The HSS-EW9Co10 composition with 10% cobalt provides a balance of toughness and wear resistance that suits demanding engraving operations. The increased hardness level (65–69 HRC) helps maintain edge geometry under intermittent contact and repeated contouring, which reduces the frequency of regrinding and tool changes. For production environments where predictable tool life and reduced stoppages matter, this tool delivers measurable efficiency gains by keeping setup times low and process stability high. Predictable results from tight dimensional control Consistent component quality starts with reliable tooling. The cutter’s diameter 4 mm and h8 tolerance ensure repeatable groove widths and traceable fits when copying templates or machining fine lettering. The specified ±2 mm length tolerance and the defined cutting length create steadiness in feed and depth settings, so finishing steps are easier to program and less likely to require trial adjustments. Explaining the tolerance system: h8 signals a precise shaft fit standard, helpful when matching the cutter to collets and holders in small‑batch or serial production. Faster preparation and accurate transfer of contours A straight cutting edge with a pre-sharpened halving minimises preparatory sharpening and supports immediate use after installation. For workshops handling short runs or sample production, the reduced preparation time translates into faster job starts and lower labour overheads. The geometrical consistency of the edge also improves the fidelity of engraved scripts and profile transfers during copy milling, meaning less rework and a better first‑pass yield for finished parts. Versatile for engraving and template milling applications Designed for the precise machining of lettering, contours and copying tasks, this cutter’s 63 mm overall length balances accessibility with stiffness. The combination of robustness and fine edge geometry makes it suitable for detailed decorative engraving as well as functional marking. Where clarity of line and contour accuracy are essential, the tool supports both manual and CNC‑assisted workflows, helping workshops deliver consistent, high‑quality results with fewer iterations. For expert selection and supply of the Werner Wilke Pro A engraving cutter, contact Metav Werkzeuge — reliable delivery from Emmerich and personalised technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118430010NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Engraving cutter Dimensions & tolerances Diameter: 4 mm Overall length: 63 mm Cutting length: 6 mm Diameter tolerance: h8 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 Material & properties Material: HSS-EW9Co10 Material number: 1.3207 Cobalt content: 10% Hardness: 65–69 HRC Form: Profil A Packaging unit: 1 FAQ What materials is this engraving cutter intended for? The Pro A engraving cutter by Werner Wilke (SKU 4118430010NW) is specified for precise engraving and copy milling tasks; its HSS‑EW9Co10 composition is chosen to provide enhanced wear resistance suitable for typical engraving applications. How precise is the shaft diameter and what does h8 mean? h8 indicates a close manufacturing tolerance for the shaft diameter; the Pro A engraving cutter’s diameter 4 mm with h8 tolerance ensures a predictable fit in collets and toolholders for repeatable machining. Can the cutter be used immediately or does it need sharpening? The cutter features a pre-sharpened halving and a straight cutting edge, so the Pro A engraving cutter is ready for immediate use after mounting, reducing setup time in workshop and CNC environments. What is the expected hardness and how does that affect wear? With a hardness of 65–69 HRC, the tool balances edge retention and toughness, resulting in longer intervals between regrinding when compared with lower‑alloy high‑speed steels. Is this tool suitable for both manual and CNC engraving? Yes, the Pro A engraving cutter’s geometry and tolerances make it appropriate for manual engraving tasks and for precision copy milling on CNC equipment, where consistency of profile transfer is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4mm Precision Engraving Cutter Profile A Solid Carbide, h6 Diameter Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid carbide construction, precision-ground geometry and tightly controlled tolerances for consistent engraving and copy‑milling in demanding materials; order directly via Metav Werkzeuge or consult the specialists for technical advice. Engraving cutter Pro A, Ø 4 mm, solid carbide, 40 mm overall — Werner Wilke Engraving cutter Pro A, Ø 4 mm, solid carbide, designed for precise engraving of letters and contours and for copy milling in metals and plastics. Solid carbide, fine-grain K10/K20 Precision ground with straight cutting edge Suitable for steel, grey cast iron and plastics Reliable results in a compact tool The engraving cutter Pro A is manufactured from solid carbide in fine‑grain K10/K20 quality and is precision ground to provide stable cutting performance. The compact diameter 4 mm and 40 mm overall length make the tool suitable for confined setups and CNC machines where repeatable small‑feature machining is required. The combination of material grade and grinding yields a hard, wear‑resistant cutting geometry that sustains dimensional accuracy across series production. Predictable tolerances for accurate machining The tool meets tight dimensional specifications with a diameter tolerance h6 and a length tolerance of +/- 2 mm, while the halfing is supplied pre‑ground with +0.1 tolerance. These numeric controls reduce setup variability and support close‑fit tasks such as fine lettering and profile work. For buyers evaluating interchangeability, the stated tolerances simplify tool-change planning and help maintain consistent part quality during extended runs. Versatile applications across materials Designed for engraving and contour copying, the cutter is suitable for steel, grey cast iron, non‑ferrous metals and plastics, providing a single‑tool option for mixed‑material production. The straight cutting edge and pointed profile A allow clear definition of fine contours and grooves; in practice this means fewer tool changes when switching between marking and light finishing operations. For operators unfamiliar with carbide behaviour, note that carbide’s hardness improves edge life but requires appropriate feed and speed settings to avoid chipping. Practical handling and integration into workflows With its precision‑ground shank and consistent geometry, the cutter integrates readily into standard collets and toolholders used in engraving and small‑part milling. The tool’s compact design supports reduced overhang and improved rigidity, translating into finer surface definition and lower vibration. For routine maintenance, inspection of the cutting edge under magnification and small adjustments to cutting parameters will prolong life; resharpening is generally uneconomical for such small, solid‑carbide cutters, so stock rotation is recommended for high‑volume use. Discuss application specifics with Metav Werkzeuge to ensure optimal tool selection and machine settings; Metav’s technical sales team can advise on feeds, speeds and fixture compatibility for Werner Wilke engraving cutters Technical Data Article number: 4118440020NW Product type: Engraving cutter Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: VHM Feinkorn K10/K20 Packaging unit: 1 UID: 4118440020NW Core data Diameter: 4 mm Overall length: 40 mm Cutting length: 4 mm Length tolerance: +/- 2 mm Diameter tolerance: h6 Halfing tolerance: +0.1 Special features Profile A Precision ground Straight cutting edge (halfing pre‑ground) Suitable for steel, grey cast iron, non‑ferrous metals and plastics Solid carbide, fine‑grain K10/K20 For engraving letters, contours and copy milling FAQ What materials can be machined with this engraving cutter? The engraving cutter Pro A is suitable for steel, grey cast iron, non‑ferrous metals and plastics, allowing use across common workshop substrates. How precise are the dimensions of the tool? Dimensions are controlled to diameter tolerance h6 and length tolerance +/- 2 mm, with the halfing supplied pre‑ground to +0.1, ensuring consistent fitting and repeatability. Is the cutting edge ready for immediate use? The tool is precision ground and supplied with a straight cutting edge, ready for immediate machining; minor parameter adjustment may be required depending on machine and material. Can this cutter be used for copy milling tasks? Yes, the geometry and profile make it suitable for copy milling of fine contours as well as engraving of letters and detailed features. What toolholder interfaces are recommended? Use a rigid collet or toolholder matching the cutter dimensions and ensure minimal overhang to maintain rigidity; the tool’s compact 40 mm overall length supports short projection setups. Is resharpening recommended for solid‑carbide engraving cutters? For small solid‑carbide cutters like this, resharpening is generally uneconomical; a rotation strategy with spare cutters is advised for high utilisation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4mm Profile A Solid Carbide Engraving Bit, Precision Ground H6 Diameter, ±2mm Length, Halfing +0.1 - Werner Wilke Zerspanungstechnik GmbH
Benefit from the combination of solid carbide fine‑grain K10/K20, a precision‑ground Profile A geometry and a straight, centre‑cutting edge to achieve repeatable engraving and efficient copy milling; order directly via Metav Werkzeuge or consult our specialists for tailored technical advice. Engraving cutter Pro A, Ø 4 mm, solid carbide, overall length 75 mm — Werner Wilke Engraving cutter Pro A Ø 4 mm engineered for precise lettering, contour engraving and copy milling across a wide range of materials Solid carbide fine-grain K10/K20 Precision ground, Profile A Straight cutting edge, centre-cut pre-ground Suitable for steel, cast iron and plastics Precision that keeps production consistent The tool is made from solid carbide in fine‑grain K10/K20 quality and is precision ground to tight dimensions, which translates directly into stable process performance. With a diameter tolerance h6 and length tolerance ±2 mm, the cutter minimises positional variation during engraving and routing operations. The Ø 4 mm tip and overall length 75 mm provide a compact geometry that reduces vibration and improves repeatability, resulting in fewer rejects and less rework in serial production. Engineered for versatile engraving and copy milling Profile A with a straight cutting edge and a centre‑cut pre‑ground configuration allows controlled starting in the workpiece and reliable contour following during copy milling. The tool is suitable for machining steel, grey cast iron, non‑ferrous metals and plastics, enabling a single cutter to cover lettering, fine contours and template‑guided routing tasks. The precision of the geometry minimises burr formation and ensures clean letterforms, which is particularly beneficial for labelling, control panels and decorative engraving. Operational advantages and setup reliability Dimensional accuracy reduces the time spent on tool offsets and fixture adjustments: the h6 tolerance on diameter and the centre‑cut tolerance +0.1 mm support consistent fits in collets and predictable plunge behaviour. The pre‑ground centre cutting edge shortens setup procedures while the fine‑grain carbide base enhances wear resistance during continuous operation. Supplied in single units for controlled stock rotation, the cutter is a practical addition to toolrooms and small production lines seeking dependable engraving performance without unnecessary complexity. For supply and technical consultation on the Werner Wilke engraving cutter Pro A (SKU 4118440025NW), contact Metav Werkzeuge GmbH in Emmerich by phone or email for reliable delivery and expert guidance Technical Data Article number: 4118440025NW Product: Engraving cutter Pro A, Ø 4 mm Brand: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 75 mm Cutting length: 4 mm Diameter tolerance: h6 Length tolerance: ±2 mm Centre‑cut tolerance: +0.1 mm Packaging unit: 1 Special features Material: solid carbide, fine‑grain K10/K20 Profile: Profile A Finish: precision ground Cutting edge: straight, centre‑cut pre‑ground Applications: engraving of lettering and contours, copy milling Suitable materials: steel, grey cast iron, non‑ferrous metals, plastics FAQ Is this cutter suitable for plunge cutting into the workpiece? The cutter has a centre‑cut pre‑ground straight edge which permits controlled starts in the material; the engraving cutter Pro A is therefore suitable for limited plunge operations and safe contour entry. Which materials can be machined with this tool? This engraving cutter from Werner Wilke is designed for steel, grey cast iron, non‑ferrous metals and a variety of plastics, covering common workshop and industrial engraving tasks. What do the tolerances mean for daily use? The h6 diameter tolerance and ±2 mm length tolerance ensure consistent clamping and repeatable tool offsets, reducing setting time and improving positional accuracy on CNC or template‑guided equipment. How does the fine‑grain K10/K20 carbide affect tool life? Fine‑grain carbide offers improved wear resistance and edge stability compared with coarser grades, extending service life under typical engraving and copy milling conditions. Is the cutter supplied individually or in sets? The tool is supplied as a single unit (packaging unit 1), which supports selective stocking and controlled replacement in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Engraving Cutter Profile A Solid Carbide K10/K20 Precision Ground, h6 Tolerance, +/−2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid-carbide construction, precision-ground Profile A geometry and tight tolerances for reliable engraving and copy milling results; order the tool via Metav Werkzeuge or request tailored technical advice. Werner Wilke Pro A engraving cutter — 5 mm, solid carbide, fine-grain The Werner Wilke Pro A engraving cutter is a precision-ground solid-carbide tool designed for engraving lettering, contours and copy milling across steel, grey cast iron, non-ferrous metals and plastics. Solid carbide, fine-grain K10/K20 Precision-ground with Profile A Straight cutting edge, halfing pre-ground Suitable for steel, cast iron, non-ferrous and plastics Consistent precision for repeatable engraving results Built from solid carbide in fine-grain K10/K20, this engraving cutter delivers consistently sharp performance and dimensionally stable cutting. The 5 mm diameter and 50 mm overall length are manufactured to close tolerances, including diameter tolerance h6 and length tolerance +/- 2 mm, which reduces the need for repeated alignment and calibration. The precise geometry means less tool deviation during high-precision tasks, translating into dependable contours and legible lettering in serial production. Versatile cutting behaviour across diverse materials The tool’s straight cutting edge and Profile A form optimise chip formation for a wide range of substrates, from mild steel and grey cast iron to aluminium alloys and common engineering plastics. A cutting length of 5 mm provides controlled engagement depth for fine detail work, while the pre-ground halfing facilitates accurate centring for engraving and copy milling. This combination produces clean edges and minimal burrs, making post-processing shorter and more predictable for small-batch and in-house production work. Durable design that fits into existing workflows Fine-grain carbide and precision-ground surfaces increase wear resistance and extend tool life under standard machining conditions. The pre-ground halfing and tight tolerances help to speed up setup and reduce scrap rates, supporting efficient shop-floor throughput. As a standardised tool with Packaging unit: 1, it integrates easily into tool lists and inventory systems, supporting both individual bench use and automated spindle tooling without complex adaptations. Contact Metav Werkzeuge for personalised technical advice on fitting the Werner Wilke Pro A engraving cutter into specific applications; call +49 2822 7131930 or email info@metav-werkzeuge.com for prompt support from Emmerich. Technical data SKU: 4118440030NW Product type: Engraving cutter Material: Solid carbide, fine-grain K10/K20 Diameter: 5 mm Cutting length: 5 mm Overall length: 50 mm Diameter tolerance: h6 Length tolerance: +/- 2 mm Halfing tolerance: +0.1 Packaging unit: 1 Facts Diameter: 5 mm Cutting length: 5 mm Overall length: 50 mm Length tolerance: +/- 2 mm Diameter tolerance: h6 Halfing tolerance: +0.1 Special features Profile A Precision-ground Straight cutting edge (halfing pre-ground) Suitable for steel, grey cast iron, non-ferrous metals, plastics For engraving lettering, contours and copy milling FAQ What materials can this engraving cutter machine handle? The Werner Wilke Pro A engraving cutter is suitable for steel, grey cast iron, non-ferrous metals and common engineering plastics, offering controlled chip formation across these substrates. What do the tolerance designations mean for workshop setup? Diameter tolerance h6 and length tolerance +/- 2 mm indicate tight dimensional control; the Werner Wilke Pro A engraving cutter therefore reduces the need for repeated micro-adjustments during tool changeover. How does the pre-ground halfing influence performance? The pre-ground halfing improves centring and reduces start-up drift when engraving or copy milling, enabling more accurate lettering and contour work from the first pass. Is this tool appropriate for copy milling small mould details? Yes, the combination of Profile A, a straight cutting edge and a 5 mm cutting length makes the tool well suited for precise reproduction of mould details and small contours. How long can the tool be expected to run under normal conditions? Tool life depends on material, cutting parameters and machine rigidity, but the fine-grain solid carbide construction of this cutter is designed to increase wear resistance and support longer intervals between replacements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5mm Profile D Solid Carbide Engraving Bit Precision Ground 60° Point, h6 Tolerance, +/-2mm Length - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid carbide construction, precision diameter tolerance h6 and sharp 60° tip geometry for accurate engraving and reduced rework. Order the tool directly via Metav Werkzeuge or consult the team for application-specific advice. Pro D engraving cutter 5 mm — solid carbide, precision-ground with 60° tip by Werner Wilke Pro D engraving cutter for fine lettering, contour engraving and copy milling across steel, grey cast iron, non‑ferrous metals and plastics Solid carbide fine-grain K10/K20 5 mm diameter, tolerance h6 60° sharp tip, semi-ground Precision-ground profile D For steel, cast iron and plastics Consistent engraving accuracy for repeatable results The combination of 5 mm diameter with a tight h6 tolerance and a precision-ground profile D delivers highly reproducible engraving paths on CNC machines and pantographs. The defined diameter tolerance ensures a secure fit in standard collets and minimises runout, which translates into consistent line width and reduced microscopic deviation when producing serial nameplates, control panels or moulded parts. This level of dimensional control helps maintain first-pass quality and lowers downstream inspection effort. Long tool life and stable cutting performance Made from solid carbide in a fine-grain K10/K20 grade, the tool resists abrasive wear and maintains edge integrity over extended runs. The 60° tip, semi-ground and supplied with a pre-sharpened half, supports crisp letter edges and precise internal corners while the 7.5 mm cutting length provides sufficient engagement for shallow engraving and contouring tasks. Fine-grain carbide improves toughness and wear resistance compared with coarser grades, which reduces frequency of tool changes and contributes to steady production throughput. Versatile for a wide range of materials and workflows Engineered for marking and copy milling, the cutter is suitable for steel, cast iron, non‑ferrous metals and plastics, enabling one tool to serve multiple production needs and lessen tool inventory. The 50 mm overall length presents a balanced stick‑out for stable machining in compact setups. Where high repeat accuracy is required, the geometry and tolerance combination facilitates clean edges and minimal burr formation, supporting faster post‑processing and a more uniform surface finish. Practical benefits for the workshop The design reduces set-up time and inspection loops: predictable tool behaviour means fewer trial runs and simpler CAM parameter transfer between jobs. The semi-ground 60° point simplifies engraving of fine text and tight contours, while the solid carbide construction offers a dependable compromise between hardness and fracture resistance. For shops tackling serial marking, sample production or small-batch copy milling, this tool offers an efficient, low-maintenance option that preserves component quality over longer cycles. For precision engraving with Werner Wilke’s Pro D cutter, contact Metav Werkzeuge for expert application advice and reliable supply from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: 4118440085NW Product type: Gravierstichel (engraving cutter) Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: VHM Feinkorn K10/K20 Diameter tolerance: h6 Packaging unit: 1 Numerical data Diameter: 5 mm Overall length: 50 mm Cutting length: 7.5 mm Tip angle: 60° Length tolerance: +/- 2 mm Special features Profile D Precision-ground Semi-ground 60° cutting edge (half pre-sharpened) For steel, grey cast iron, non‑ferrous metals and plastics Solid carbide fine-grain construction FAQ What materials can this engraving cutter process? The Pro D engraving cutter is suitable for steel, grey cast iron, non‑ferrous metals and plastics, allowing versatile use across marking and copy milling tasks. What does the h6 diameter tolerance mean for assembly? A diameter tolerance of h6 signifies a close manufacturing tolerance for the 5 mm shaft, ensuring a snug, repeatable fit in precision collets and minimising runout during machining. How does the fine-grain K10/K20 carbide affect tool life? The fine-grain K10/K20 carbide grade increases wear resistance and edge stability, extending life compared with coarser grades and reducing tool-change frequency under comparable conditions. Is the cutter ready for immediate use or does it require sharpening? The cutter is supplied semi-ground with the 60° tip half pre-sharpened so it is ready for most engraving tasks; final adjustments can be made depending on machine and application needs. Which SKU should be referenced when ordering or specifying the tool? Reference SKU 4118440085NW (Pro D engraving cutter, 5 mm) when ordering or documenting tool lists. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6mm Profile D Engraving Cutter Solid Carbide K10/K20 Precision Ground 60° Tip, h6 Tolerance - Werner Wilke Zerspanungstechnik GmbH
Combines solid carbide durability with a sharp 60° tip for crisp engraving and reliable copy milling; the fine‑grain K10/K20 grade and tolerance h6 ensure repeatable fits and long service life. Order the Pro D engraving cutter directly via Metav Werkzeuge or ask our consultants if needed. Pro D engraving cutter — 6 mm solid carbide, 60° tip, Werner Wilke The Pro D engraving cutter is a precision tool for fine lettering, contour work and copy milling across steels, grey cast iron, non‑ferrous metals and plastics. Solid carbide VHM, fine-grain K10/K20 Precision-ground profile D, sharp 60° tip For steel, grey cast iron, non-ferrous metals 6 mm diameter, tolerance h6; length ±2 mm High-precision edges for crisp lettering and contours Manufactured from solid carbide (VHM) in a fine-grain K10/K20 quality, this engraving cutter delivers defined edges and consistent wear resistance. The 6 mm shank with tolerance h6 gives predictable concentricity when clamped, reducing runout and improving finish quality in both manual and CNC setups. The precision-ground geometry minimises vibration and supports clean letterforms even on tougher substrates, turning machining parameters into reproducible outcomes. Geometry that matches the task — sharper grooves, cleaner copies The profile D geometry with a 60° cutting angle creates narrow V‑grooves ideal for lettering and contour definition; the design is suited to traditional engraving and modern copy milling processes alike. Because the tip angle concentrates cutting forces, the result is clear, legible engraving with minimal burr formation on steel, grey cast iron, non‑ferrous metals and plastics. The tool’s configuration reduces the need for multiple tool changes when producing fine details and replicated contours. Repeatable set-up and controlled cutting depth for consistent results With an overall length of 75 mm and a cutting length of 9 mm, the tool balances accessibility and stiffness for short to medium depth engraving. The stated length tolerance of ±2 mm supports consistent clamping and Z‑axis positioning across batches, while the precision-ground finish supports long-term repeatability. These attributes simplify fixture planning and shorten set-up times, supporting efficient production cycles without sacrificing surface quality. Order the Werner Wilke Pro D engraving cutter via Metav Werkzeuge for dependable precision and steady supply from Emmerich — contact info: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: 4118440090NW Label: Gravierstichel Pro D D.6mm VHM Gesamt-L.75mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Gravierstichel Form: Profil D Material: VHM Feinkorn K10/K20 Core technical data Diameter: 6 mm Overall length: 75 mm Cutting length: 9 mm Tip angle: 60° Diameter tolerance: h6 Length tolerance: ±2 mm Special features Precision-ground Sharp 60° cutting edge (half pre-ground) Suitable for engraving and copy milling Application: steel, grey cast iron, non-ferrous metals, plastics FAQ Which materials are suitable for this engraving cutter? The Pro D engraving cutter from Werner Wilke (SKU 4118440090NW) is specified for steel, grey cast iron, non‑ferrous metals and plastics, reflecting its fine‑grain VHM construction and geometry. What does tolerance h6 on the diameter mean for clamping? Tolerance h6 indicates a close fit on a 6 mm shaft; in practice this ensures consistent concentricity when clamped in precision collets and reduces runout for finer engraving. How deep can the cutter engrave reliably? The tool has a cutting length of 9 mm; for repeatable shallow to moderate engraving depths the 9 mm engagement is recommended to maintain stiffness and surface quality. Is the cutter suitable for CNC copy milling of contours? Yes, the profile D geometry and 60° tip are designed for clear contour definition and are suitable for copy milling tasks that require precise groove profiles. Are there recommendations for preserving tool life? The Werner Wilke Pro D engraving cutter’s fine-grain VHM construction supports wear resistance; machining with appropriate feeds, speeds and effective chip evacuation will extend service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Precision Engraving Cutter D.8mm Solid Carbide K10/K20 Profile A +0.1 Tolerance, h6 Diameter - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a combination of solid carbide fine-grain K10/K20 and precision-ground geometry for consistent engraving quality and extended tool life; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Werner Wilke Pro A engraving cutter D 8 mm – solid carbide, 75 mm overall length The Werner Wilke Pro A engraving cutter is a precision-ground, solid carbide tool designed for engraving letters, contours and copy milling across a range of materials in industrial and workshop environments Solid carbide, fine-grain K10/K20 Precision-ground with straight cutting edge Suitable for steel, cast iron, non-ferrous and plastics Diameter tolerance h6, length tolerance ±2 mm Reliable, measurable accuracy for repeatable results The engraving cutter is manufactured from solid carbide fine-grain K10/K20, delivering consistent edge geometry and wear resistance that translates into predictable machining results. The precision-ground profile minimises run-out and vibration, while the specified diameter tolerance h6 and length tolerance ±2 mm ensure compatibility with repeatable set-ups. These measurable attributes reduce scrap rates and make process planning more reliable in batch production. One tool for multiple materials to simplify workflows Built for machining steel, cast iron, non-ferrous metals and plastics, the tool reduces the need for frequent tool changes by covering a wide application spectrum. The combination of material choice and profile A geometry enables clean engraving and accurate contour work, which shortens set-up times and increases throughput. For operations that handle diverse components, this versatility contributes directly to operational efficiency. Improved edge life and surface quality for fewer interruptions The fine-grain carbide substrate offers enhanced hardness and toughness compared with coarser grades, leading to superior wear resistance and longer intervals between regrinds or replacements. As a result, the engraving tool maintains a consistent cutting edge for longer runs, delivering better surface quality on engraved letters and contours and lowering rework rates. The straight cutting edge and pre-sharpened finish also support crisp detail reproduction in delicate lettering and intricate shapes. Predictable integration into existing processes and jigs With a diameter of 8 mm and an overall length of 75 mm, the cutter provides clear dimensional data for fixture and holder selection. The tool’s tolerances and precision finishing support fast installation into standard toolholders and ensure stable cutting conditions. Emphasis on verifiable specifications enables smoother qualification for CNC programmes and repeat jobs, making this cutter suitable for both prototyping and series production. Contact Metav Werkzeuge for tailored application advice on the Werner Wilke Pro A engraving cutter and secure reliable delivery from Emmerich; eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: 4118440040NW Product name: Gravierstichel Pro A D.8mm VHM Gesamt-L.75mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Diameter: 8 mm Overall length: 75 mm Cutting length: 8 mm Diameter tolerance: h6 Length tolerance: ±2 mm Halfing tolerance: +0.1 Special features Solid carbide fine-grain K10/K20 Profile A Precision-ground Straight cutting edge, pre-sharpened For engraving letters, contours and copy milling Suitable for steel, cast iron, non-ferrous metals and plastics FAQ What materials can be machined with the Werner Wilke Pro A engraving cutter? The Werner Wilke Pro A engraving cutter is suitable for steel, cast iron, non-ferrous metals and plastics, making it versatile for mixed-production environments. What tolerances can be expected from the cutter? The tool is supplied with a diameter tolerance h6 and a length tolerance of ±2 mm, providing predictable dimensional accuracy for fixture and programme set-up. Is the tool ready for immediate use or does it require additional preparation? The cutter is precision-ground with a straight cutting edge and delivered pre-sharpened for immediate integration into machining operations, reducing set-up time. How does the fine-grain K10/K20 material benefit production? The fine-grain carbide K10/K20 offers enhanced wear resistance and edge retention, leading to longer tool life and improved surface quality on engraved details. Which operations is the cutter specifically designed for? This tool is intended for engraving of letters and contours as well as copy milling, where precise detail and repeatability are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Profil A Solid Carbide Engraving Cutter D.10mm, h6 Tolerance / +/- 2 mm Length, Halfing +0.1 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a durable, solid carbide construction combined with precision-ground geometry and tight tolerances to ensure clean engraving and consistent process stability; order directly via Metav Werkzeuge or consult Metav’s specialists for specification support. Pro A engraving cutter – 10 mm solid carbide, 75 mm overall (Werner Wilke) The Pro A engraving cutter is a precision-ground, solid carbide tool designed for engraving lettering, contours and copy milling across a wide range of workshop materials. Solid carbide, fine‑grain K10/K20 Precision‑ground Profile A design Suitable for steel, cast iron, non‑ferrous metals 10 mm diameter, 75 mm overall length Precision that reduces scrap and repeat work Built from solid carbide in fine‑grain K10/K20, this engraving cutter delivers consistently sharp edges and superior wear resistance compared with conventional grades. The precision‑ground geometry and h6 diameter tolerance ensure repeatable concentricity, which reduces runout and the need for reworking. For process planners, the combination of a hardened substrate and stable manufacturing tolerances translates into fewer rejects and more predictable cycle times when engraving small letters or detailed contours. Versatile material compatibility for mixed‑workshop use The tool is specified for machining steel, grey cast iron, non‑ferrous metals and plastics, allowing a single cutter to serve multiple applications in one fixture set‑up. With a cutting length optimised for detail work, the cutter supports tasks from fine lettering to shallow profile copying. This versatility improves throughput in setups where different materials are processed in sequence, removing the requirement to change tooling as often and simplifying tool inventory management. Geometry and tolerances engineered for precise results Featuring Profile A and a straight cutting edge with the half‑cut pre‑ground, the tool stabilises chip formation and keeps marks on engraved edges crisp. The nominal 10 mm diameter, 10 mm cutting length and 75 mm overall length provide a balanced reach without sacrificing stiffness. Length and position tolerances (length ±2 mm; half‑cut tolerance +0.1) are specified to maintain predictable axial position during copy milling, which is especially important for repeat engraving on batch parts. Integration into the production chain and procurement advantages When combined with correct speeds and feeds for the selected substrate, the cutter offers an efficient balance of surface quality and tool life. The tool’s design supports higher spindle speeds and fine finishing passes, enabling shorter cycle times for small‑scale engraving runs. For purchasing and logistics, Metav’s presence in Emmerich acts as a practical quality filter for the European market, offering a broad catalogue and dependable supply chains that support workshop uptime and procurement simplicity. Contact Metav Werkzeuge for technical specification advice and to arrange procurement from Emmerich; Metav’s consultants can assist with application parameters and delivery options. Technical data Article number: 4118440045NW Product type: Engraving cutter Brand: Werner Wilke Zerspanungstechnik GmbH Form: Profile A Label: Gravierstichel Pro A D.10mm VHM Gesamt-L.75mm WERNER WILKE Facts Diameter: 10 mm Cutting length: 10 mm Overall length: 75 mm Diameter tolerance: h6 Length tolerance: +/- 2 mm Half‑cut tolerance: +0.1 Special features Solid carbide, fine‑grain K10/K20 Profile A, precision‑ground Straight cutting edge; half‑cut pre‑ground Applications: engraving lettering and contours, copy milling Material applications: steel, grey cast iron, non‑ferrous metals, plastics FAQ What materials can this engraving cutter machine handle? The Pro A engraving cutter from Werner Wilke is specified for steel, grey cast iron, non‑ferrous metals and plastics, covering the typical spectrum for detailed engraving and copy milling. What tolerances can be expected from the tool? The cutter is manufactured to h6 diameter tolerance, with a length tolerance of ±2 mm and a half‑cut tolerance of +0.1, ensuring consistent axial positioning during engraving operations (SKU 4118440045NW). Is the tool suitable for fine lettering and shallow reliefs? Yes, the combination of 10 mm diameter, 10 mm cutting length and the precision‑ground Profile A geometry makes it well suited to fine lettering and shallow contour work where edge definition is critical. Does the cutter include any coating or surface treatment? No coating is specified for this item; the performance and wear resistance are delivered by the fine‑grain K10/K20 solid carbide substrate and the precision grinding of the cutting geometry. How does the half‑cut pre‑ground feature affect performance? The half‑cut pre‑ground configuration improves chip control and reduces burr formation on shallow engravings, helping to maintain clean contours and consistent surface finish across batch parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Profile A Engraving Tip 6mm Solid Carbide Precision Ground, h6 Tolerance ±2mm - Werner Wilke Zerspanungstechnik GmbH
Benefit from the combination of solid carbide fine‑grain K10/K20 and a precision‑ground straight cutting edge for consistent engraving and copy milling results; the tool’s 6 mm diameter and tight h6 tolerance ensure reproducible fits and contours. Order directly via Metav Werkzeuge or contact the consultants for application advice and delivery from Emmerich. Werner Wilke Pro A engraving cutter — 6 mm solid carbide, 75 mm overall The Pro A engraving cutter is a precision‑ground, solid‑carbide tool designed for engraving lettering and contours and for copy milling in steel, grey cast iron, non‑ferrous metals and plastics. Solid carbide, fine‑grain K10/K20 Precision‑ground with straight cutting edge Suitable for steel, cast iron, non‑ferrous and plastics Diameter tolerance h6, length tolerance ±2 mm Consistent engraving quality for demanding tasks The Pro A engraving cutter delivers repeatable results through its solid carbide construction and fine‑grain K10/K20 microstructure, which together reduce flank wear and preserve edge geometry over longer tool life. The combination of a precision‑ground body and a straight cutting edge provides clean contour definition and predictable material removal, making the cutter suitable for detailed lettering and shallow relief work. For production environments, the tight h6 diameter tolerance contributes to consistent positioning and reduced rework during copy milling operations. Material versatility that widens workshop capability Made for a broad range of substrates, this tool supports machining of steel, grey cast iron, non‑ferrous metals and plastics, enabling one cutter to cover multiple tasks and reduce tool changes. The tool’s geometry and pre‑ground centring ensure reliable engagement when initiating cuts and improve control when following templates or CNC toolpaths. For users with mixed‑material jobs, the robust carbide grade offers a balance between toughness and wear resistance, lowering the need for frequent replacement and helping maintain throughput in small and medium workshops. Practical integration into machining workflows With a 6 mm diameter and an overall length of 75 mm, the cutter fits common collet systems while offering sufficient reach for shallow to moderate depth engraving and copying operations. The ±2 mm length tolerance and the +0.1 mm centre tolerance simplify tool offset settings and reduce setup time, increasing machine uptime. Clear numerical specifications and the tool’s compact profile make it straightforward to specify for fixture planning and to include in tool lists for repeat orders, supporting efficient procurement and production planning. For reliable high‑precision engraving with Proven Werner Wilke quality, contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118440035NW Label: Gravierstichel Pro A D.6mm VHM Gesamt‑L.75mm WERNER WILKE Product: engraving cutter, Profil A Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core specifications Diameter: 6 mm Overall length: 75 mm Cutting length: 6 mm Diameter tolerance: h6 Length tolerance: ±2 mm Centre/halving tolerance: +0.1 mm Materials & features Material: solid carbide, fine‑grain K10/K20 Profile: Profil A Geometry: precision‑ground, straight cutting edge, pre‑ground centring Applications: steel, grey cast iron, non‑ferrous metals, plastics Packaging unit: 1 FAQ What materials can be machined with this engraving cutter? The Pro A engraving cutter from Werner Wilke is suitable for steel, grey cast iron, non‑ferrous metals and plastics, as stated in the tool specifications. What does the h6 diameter tolerance mean for setup? An h6 tolerance indicates a tight, repeatable shaft diameter that simplifies collet selection and reduces radial play, improving positional accuracy during engraving and copy milling. Is the tool suitable for plunge or centre cuts? The cutter features a straight cutting edge with pre‑ground centring to aid initial engagement; it is intended for engraving and template‑guided copy milling rather than aggressive plunging in hard materials. How long is the tool and how does that affect reach? The overall length is 75 mm, providing sufficient reach for most engraving and shallow copy‑milling tasks while remaining compatible with standard collet systems. Which SKU should be ordered for this Pro A cutter? Order the cutter under SKU 4118440035NW; this references the Pro A engraving cutter (6 mm, solid carbide) by Werner Wilke. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Profile D Engraving Bit 4mm Solid Carbide K10/K20, h6 Diameter Tolerance, 60° Tip - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid carbide durability, 60° precision-ground tip and reliable h6 diameter accuracy for consistent engraving and copy-milling results. Order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Pro D Engraving Cutter, 4 mm, Solid Carbide, 60° Tip — Werner Wilke The Pro D engraving cutter is a 4 mm solid-carbide tool designed for precise lettering, contour engraving and copy milling across metal and plastic workpieces. Solid carbide K10/K20 fine-grain Sharp 60° precision-ground tip Diameter tolerance h6 for accuracy For steel, cast iron and plastics High-precision geometry for reliable engraving results This engraving tool combines a solid carbide construction in K10/K20 fine-grain quality with a 60° tip that is precision-ground for repeatable edge definition. The small 4 mm diameter and narrow tip angle ensure crisp character shapes and faithful contour reproduction when working on lettering or fine profiles. As a consequence, setups stay predictable and finishing work is minimised, which supports higher throughput without sacrificing detail. Built for versatile workshop and CNC applications With a 75 mm overall length and 6 mm cutting length, the cutter is suited to both handheld engraving heads and CNC copy-milling machines where controlled engagement and reach are required. The h6 tolerance on the diameter guarantees a snug fit in collets and spindle adaptors, reducing runout and vibration. These measurable properties translate into consistent cutting behaviour on steel, grey cast iron, non-ferrous metals and plastics, so production tolerances are easier to maintain and rework is reduced. Practical handling and process benefits The tool arrives single packed for immediate installation and features a precision-ground cutting geometry with a sharp 60° edge, partly pre-finished to assist initial penetration and accuracy. The relatively short cutting length concentrates the cutting forces close to the tool body, which helps to prolong service life and deliver consistent tool life across batches. For operations that demand fine detail — from serial nameplate engraving to template-controlled copy milling — integration into existing tool holders is straightforward thanks to the defined diameters and tolerances. For tailored advice on implementing this Werner Wilke Pro D engraving cutter in specific machines or materials, please contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: 4118440080NW Product: Pro D engraving cutter Material: Solid carbide fine-grain K10/K20 Product type: Engraving cutter Tip angle: 60° Cutting length: 6 mm Overall length: 75 mm Diameter: 4 mm Diameter tolerance: h6 Length tolerance: +/- 2 mm Packaging unit: 1 UID: 4118440080NW Facts Diameter (mm): 4 Overall length (mm): 75 Cutting length (mm): 6 Tolerance diameter: h6 Tolerance length: +/- 2 mm Special features Precision-ground 60° cutting edge (half-angle pre-ground) Suitable for engraving and copy milling For steel, grey cast iron, non-ferrous metals and plastics Fine-grain solid carbide for wear resistance FAQ Which materials can this engraving cutter machine effectively? The Pro D engraving cutter (Werner Wilke, SKU 4118440080NW) is specified for steel, grey cast iron, non-ferrous metals and plastics, offering versatility for engraving and copy-milling tasks. What tolerances can be expected for fitting and length? Diameter tolerance is h6 for accurate clamping, and length tolerance is +/- 2 mm, which helps to ensure reproducible setup and consistent machining depth with the Pro D engraving cutter. Is the cutting edge ready for immediate use or does it need finishing? The tool features a precision-ground 60° tip with partial pre-finishing to support immediate use for fine engraving; further finishing depends on the specific material and machining strategy. Can the cutter be used in CNC copy-milling operations? Yes, the combination of 4 mm diameter, defined tolerances and 6 mm cutting length makes this cutter suitable for integration into CNC copy-milling setups that handle detailed contours and lettering. Which tool holders or collets are compatible with this cutter? The cutter’s 4 mm diameter is compatible with standard collets and tool holders designed for 4 mm shanks; correct clamping to h6 tolerance is recommended to minimise runout. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8mm Engraving Bur Profile A HSS-EW9Co10 10% Cobalt Hardened 65-69 HRC, h8 Diameter +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a hardened, precision-ground engraving cutter with a high-cobalt HSS grade and tight diameter tolerance for reliable, repeatable engraving and copy milling; benefit from its 8 mm shank and 12 mm cutting length designed for fine contours and lettering. Order directly via Metav Werkzeuge or consult the product specialists for application advice. Werner Wilke Pro A engraving cutter, 8 mm – HSS‑EW9Co10, 90 mm overall Werner Wilke Pro A engraving cutter for detailed engraving, contour work and copy milling, manufactured from HSS‑EW9Co10 and precision ground for consistent results Hardened HSS with 10% cobalt Diameter 8 mm, tolerance h8 For engraving and copy milling Precision ground, hardened and tempered High‑performance cutting for precise engraving The HSS‑EW9Co10 construction with an elevated cobalt content provides increased red‑hardness and wear resistance compared with standard high‑speed steels, supporting sustained cutting performance when profiling fine letters and contours. The tool is hardened, tempered and precision ground, which ensures a consistent cutting geometry and repeatable results in series work. Tight dimensional control—diameter tolerance h8 and length tolerance ±2 mm—reduces setup variance and shortens machining time, while the 12 mm cutting length allows controlled engagement for delicate features. Consistent quality that improves workflow This solid‑steel engraving tool is engineered to keep processing stable: the straight cutting edge and pre‑ground halfing aid in reliable centre entry and clean contour transitions. As a consequence, tool changes and rework are minimised, delivering a measurable improvement in cycle reliability and a lower rate of rejects. The robustness of the material and the 65–69 HRC hardness rating of the cutting portion support frequent use in toolrooms and small production runs where repeatability and surface finish matter. Practical compatibility and application clarity Suitable for use on a variety of non‑ferrous and ferrous substrates in precision applications, this cutter excels for fine scripts, logos and template copying. The 8 mm dimension makes it compatible with common tool holders and collets found in engraving machines and small CNC routers, enabling straightforward integration into existing setups. The tool’s specification explicitly states its application for engraving of lettering and contours as well as for copy milling, so selection is clear for workshop planners and machinists seeking a specialist finishing instrument. Built for professional environments and predictable supply The component’s traceable material designation (1.3207) and the explicit tolerances allow planners to document process capability and inspection criteria with ease. The tool is delivered as a single‑item packaging unit, easing stock control for procurement teams. In addition, the combination of precise grinding and a defined halfing tolerance +0.1 supports reliable fixturing and minimal runout when mounted correctly, which translates into improved surface quality and less polishing or rework downstream. Contact Metav Werkzeuge for ordering, technical clarification or to discuss suitability for specific materials and machines – telephone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: 4118430020NW Label: Gravierstichel Pro A D.8mm HSS-EW9Co10 1.3207 Gesamt-L.90mm WERNER WILKE Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Diameter: 8 mm Overall length: 90 mm Cutting length: 12 mm Hardness: 65–69 HRC Cobalt content: 10 % Diameter tolerance: h8 Length tolerance: ±2 mm Halfing tolerance: +0.1 Special features Material: HSS‑EW9Co10 Material number: 1.3207 Form: Profil A Hardened, tempered and precision ground Straight cutting edge, halfing pre‑ground (D x 1.5) Application: engraving of lettering and contours, copy milling Packaging unit: 1 FAQ What materials is this engraving cutter suitable for? The Werner Wilke Pro A engraving cutter (HSS‑EW9Co10) is specified for fine engraving and copy milling tasks and is suited to a range of common workshop materials where high‑speed steel performance is appropriate. How precise are the diameter and length of the tool? Diameter tolerance for the Werner Wilke Pro A engraving cutter is h8, with a length tolerance of ±2 mm, enabling predictable mounting and machining outcomes. Can the tool be used for copy milling on templates? Yes, the tool is explicitly designed for engraving of scripts and contours as well as for copy milling applications, benefiting from its precision ground edge and pre‑ground halfing. Is the material traceable for quality documentation? The cutter is manufactured from HSS‑EW9Co10 with material number 1.3207, which supports traceability for quality and process documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8mm Profil D Solid Carbide Engraving Cutter Precision Ground 60° Tip, h6 Tolerance +/-2mm - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of solid carbide fine‑grain K10/K20, a precision‑ground 60° cutting edge and tight h6 diameter tolerance for reliable engraving and contour work; order the tool via Metav Werkzeuge or contact our consultants for application advice. Pro D Engraving Cutter – 8 mm Solid Carbide, 60° Tip (Werner Wilke) The Pro D engraving cutter (8 mm) by Werner Wilke is a precision solid‑carbide tool designed for fine engraving, contouring and copy milling across common workshop materials. *Solid carbide fine‑grain K10/K20 *Precision‑ground 60° sharp tip *Diameter 8 mm, tolerance h6 *Suitable for steel, cast iron and plastics Precision for smallest details Made from solid carbide in fine‑grain K10/K20, this cutter delivers a hard, wear‑resistant edge that maintains shape under repetitive engraving tasks. The fine‑grain microstructure improves edge stability and reduces chipping during contouring, which translates into fewer tool changes and less rework. The precision‑ground geometry ensures each flute meets dimensional expectations for repeatable results in serial production or sample runs. Accurate geometry for reliable contours The 60° tip provides a narrow kerf and sharp definition for letters and fine outlines, while the 12 mm cutting length balances approach depth and stiffness for controlled cuts. Dimensional control is ensured by the h6 diameter tolerance and a ±2 mm length tolerance, supporting predictable fits and consistent tool paths when used in CNC fixtures or manual engraving setups. These specifications reduce scrap and support efficient programming and fixture design. Versatility across workshop materials Engineered for engraving and copy milling, the tool is suitable for steel, cast iron, non‑ferrous metals and plastics, making it a versatile choice for toolrooms, prototyping and small‑batch production. The sharp geometry and carbide substrate enable crisp letters and contours on harder substrates while still producing clean results in softer polymers. This adaptability helps consolidate tooling stocks and simplifies process planning. Stable setup and handling for productive workflows With an 8 mm diameter and 75 mm overall length, the cutter offers a balance between reach and rigidity for many standard tool holders and collet systems. The tool’s construction and finish support stable cutting action and repeatability across runs, helping to keep cycle times consistent and supporting higher first‑pass yields. The partially pre‑ground cutting edge accelerates initial setup and reduces the need for additional finishing prior to use. For precise engraving and dependable workshop performance with Werner Wilke solid‑carbide tools, contact Metav Werkzeuge for tailored application advice or to arrange supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118440095NW Product type: Engraving cutter Manufacturer: Werner Wilke Zerspanungstechnik GmbH Form: Profile D Facts Diameter: 8 mm Overall length: 75 mm Cutting length: 12 mm Tip angle: 60° Diameter tolerance: h6 Length tolerance: ±2 mm Packaging unit: 1 Special features Material: solid carbide fine‑grain K10/K20 Precision‑ground geometry Sharp 60° cutting edge (half‑edge pre‑ground) Application: engraving of letters and contours, copy milling Suitable for steel, grey cast iron, non‑ferrous metals and plastics FAQ How precise is the tool diameter? The tool is manufactured with an h6 diameter tolerance; the 8 mm dimension meets this tolerance to ensure consistent seating and concentricity during machining. Which materials can be machined with this cutter? The cutter is suitable for steel, grey cast iron, non‑ferrous metals and plastics, enabling engraving and contour work across a wide range of workshop materials. What tip angle is best for fine lettering? A 60° tip angle is supplied, optimised for narrow kerfs and sharp, legible lettering during engraving and copy milling. Is the cutter suitable for copy milling on CNC machines? Yes; the tool’s precision‑ground geometry and stable carbide substrate make it suitable for copy milling and repeatable contour tasks in production settings. What are the tool’s overall and cutting lengths? The cutter offers a 75 mm overall length with a 12 mm cutting length and a length tolerance of ±2 mm to aid in fixture and program setup. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com