16mm Pull Screw M8 for 16mm Clamping Diameter, DIN 6367 - TECWERK
Compact, standardised and reliable: the combination of an M8 thread, 20 mm head diameter and a 16 mm overall length ensures secure seating and compact assemblies for milling operations. Order the milling clamping screw directly via Metav Werkzeuge or request compatibility advice from our consultants. Milling clamping screw M8 for 16 mm clamping diameter – TECWERK (20 mm head, 16 mm length) The Milling clamping screw M8 for 16 mm clamping diameter is a standardised fastening element for securing cutters and adaptors in compact toolholders where repeatable concentricity and easy interchangeability are required M8 thread, compatible with standard collets Conforms to DIN 6367 for interchangeability Designed for clamping Ø 16 mm 20 mm head diameter, 16 mm overall length Consistent clamping for uninterrupted production The primary advantage of this clamping screw is its consistent mechanical interface: the M8 thread and adherence to DIN 6367 reduce setup time and minimise the risk of misfit between toolholders and cutters. This leads to fewer stoppages for re-tensioning and less variation in runout, supporting a smoother production flow. The component’s standardised geometry supports rapid replacement and compatible retrofit with many commercial toolholder systems, delivering a measurable improvement in operational efficiency. Compact dimensions that suit confined toolholders With an overall length L: 16 mm, head diameter D: 20 mm and head height K: 6 mm, this clamping screw is engineered for installations where space is limited. The compact proportions allow reliable force transmission without introducing protrusion that interferes with adjacent tooling. Explaining the key dimensions: L denotes the total length, D the head diameter and K the head height – each value informs the clearance and engagement depth required in the toolholder, making selection straightforward even for non-specialist workshop staff. Practical compatibility and workshop guidance Specified for a clamping Ø 16 mm, this fastening element is suited to common milling applications where a small, repeatable locating diameter is needed. Delivered in a single-piece packaging unit, it is intended for direct installation or as a stocked spare. The part is supplied under the TECWERK designation, which simplifies procurement and traceability in maintenance records. If further verification of fit is required, Metav Werkzeuge provides technical guidance and can confirm suitability against specific toolholder models. Request tailored advice from Metav Werkzeuge for TECWERK clamping components or arrange procurement and delivery from our Emmerich hub via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000834072NW Label: Milling clamping screw M8 for 16 mm clamping diameter TECWERK Product type: Fräsanzugsschraube (milling clamping screw) Dimensions / Core data Thread: M8 Head diameter (D): 20 mm Overall length (L): 16 mm Head height (K): 6 mm Suitable for clamping Ø: 16 mm Special features / Versions Conforms to DIN 6367 Packaging unit: 1 Brand: TECWERK UID: 2000834072NW FAQ Is this clamping screw compatible with my M8 toolholder? Compatibility depends on the toolholder’s conformity to standard DIN interfaces; the Milling clamping screw M8 for 16 mm clamping diameter follows DIN 6367, which supports interchangeability with compliant holders. What do the dimension codes L, D and K mean? L refers to the overall length (16 mm), D to the head diameter (20 mm) and K to the head height (6 mm); these values determine engagement depth and clearance in the toolholder. Can the screw be used for heavy-duty milling operations? The component is designed for secure clamping where the specified interface and dimensions match the application; refer to the toolholder manufacturer’s load limits to assess suitability with the Milling clamping screw M8. How is the product supplied and tracked? The item is supplied as a single piece (packaging unit 1) and identified by article number 2000834072NW for stock and maintenance tracking. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
28mm Milling Draw Bolt M10 For 22mm Clamping Diameter, L18 K7 - TECWERK
Take advantage of a standardised M10 thread and DIN 6367 conformity for consistent clamping and reduced setup time; the compact 18 mm overall length and 28 mm head diameter ensure fit in confined toolholders. Order the TECWERK draw-in screw directly via Metav Werkzeuge or ask our consultants if required. TECWERK draw-in screw M10 — for clamping Ø 22 mm, DIN 6367 A robust draw-in screw by TECWERK, designed to secure milling cutters and tool assemblies with a standard M10 thread for clamping diameters of 22 mm. M10 thread for secure connection Suitable for clamping Ø 22 mm Conforms to DIN 6367 standard Compact 18 mm overall length Consistent clamping through standardised design The TECWERK draw-in screw provides a standard M10 thread combined with compliance to DIN 6367, enabling reliable interchangeability with common milling toolholders. This standardisation reduces the risk of misalignment and minimises rework: compatible interfaces lead to predictable axial positioning and improved repeatability of setups. For production environments where every micrometre of run-out matters, the mechanical consistency contributes directly to machining accuracy and lower scrap rates. Compact dimensions that suit confined toolholders Measured to a total length of 18 mm with a head diameter of 28 mm and a head height of 7 mm, the component's form factor prioritises space efficiency without compromising clamping force. The reduced overall length supports installations in tight collet or clamping systems while the larger head diameter distributes contact forces to maintain stable seating. These dimensional details simplify selection for assemblies where clearance and secure seating are decisive. Streamlined handling and compatibility in workshop use Specified for a clamping Ø 22 mm, the fastening element integrates into conventional clamping systems used in milling operations and CNC setups. The straightforward geometry and conformity to recognised standards enable faster changeovers and easier inventory management in the workshop. As a mechanically simple, maintenance-light solution, the screw supports uninterrupted production cycles and reduces the time spent on locating specialised fasteners. Supply reliability and professional sourcing Sourcing through Metav combines product availability with experienced procurement support: Metav offers a broad industrial range and a dependable supply chain, backed by the trust of over 48,000 customers and a catalogue of more than 250,000 products. The compact design and standard thread choice make this component a practical addition to stock lists for maintenance departments, toolrooms and precision workshops that prioritise consistent availability and verified compatibility. For availability checks or procurement advice regarding the TECWERK draw-in screw (SKU 2000834073NW), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for reliable delivery and application guidance. Technical data Article number: 2000834073NW Label: Draw-in screw M10 for clamping Ø 22 mm TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Thread: M10 Overall length L: 18 mm Head diameter D: 28 mm Head height K: 7 mm Suitable for clamping Ø: 22 mm Special features Conforms to DIN 6367 axite enrichment: L: 18mm · K: 7mm · D: 28mm SKU: 2000834073NW FAQ What thread does this clamping screw use? The component uses an M10 thread; the TECWERK draw-in screw (SKU 2000834073NW) is specified for standard M10 applications. Which clamping diameter is this screw suitable for? This fastening element is specified for a clamping Ø of 22 mm and is intended for use with compatible clamping systems and toolholders. Are the dimensions standardised for easy replacement? Yes, the part conforms to DIN 6367 and features an overall length of 18 mm, a head diameter of 28 mm and a head height of 7 mm for predictable replacements. Is this screw suitable for workshop and CNC use? The design and standard conformity make the screw appropriate for both workshop and CNC environments where standard M10 draw-in fixings are required. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
35mm Clamping Screw M12 For Clamping Ø27mm, L22mm K8mm - TECWERK
Compact M12 thread and compliance with DIN 6367 combine to provide dependable clamping for a 27 mm toolholder; take advantage of the compact 22 mm length and 35 mm head for secure seating. Order this TECWERK component directly via Metav Werkzeuge or consult our specialists for fit verification. TECWERK M12 milling clamping screw – compact M12 thread for 27 mm clamping diameters The TECWERK M12 milling clamping screw serves as a compact draw-in screw for milling toolholders and clamping systems, optimised for applications with a clamping diameter of 27 mm M12 thread for standard toolholders Designed for clamping Ø 27 mm Overall length 22 mm, head Ø 35 mm DIN 6367 conformity Consistent clamping performance for accurate machining A precise M12 thread combined with conformity to DIN 6367 ensures repeatable seating and predictable force transmission, which is crucial for milling operations that demand positional accuracy. The screw’s geometry supports consistent axial pull and stable contact between the tool and holder, reducing micro‑movement during cuts. This results in improved surface finish and tool life, as fewer compensatory adjustments are required during set‑up. The standardised specification also simplifies inventory planning in production environments where interchangeability and traceable components are essential. Faster set-up and less downtime through compact dimensions With an overall length of 22 mm and a head diameter of 35 mm (head height K 8 mm), the component is designed for compact assemblies and tight tool pockets. The short shank minimises protrusion into the toolholder, enabling quicker insertion and removal while maintaining a secure clamp. For workshops that cycle tools frequently, these dimensions translate into measurable time savings at every tool change and fewer obstructions during handling and storage, supporting leaner workflows and higher machine uptime. Industrial compatibility and reduced sourcing complexity Specification to an established standard makes the screw suitable for a broad range of holders and milling systems that accept an M12 draw-in element and a 27 mm clamping interface. The standardised profile facilitates cross‑brand compatibility and reduces the risk of procurement errors in mixed fleets. Where standardisation is part of a quality strategy, the use of DIN‑compliant components simplifies documentation and quality audits while supporting consistent assembly procedures across departments. Practical applications and workshop recommendations This clamping screw is aimed at industrial workshops, tool rooms and maintenance departments that require compact, standardised fastening for milling toolholders with a 27 mm clamping diameter. Given the absence of material data in the specification, compatibility checks with existing holders and any surface‑treatment requirements should be confirmed before installation. For bespoke toolrooms or retrofit projects, selecting a DIN‑specified fastening element like this one reduces the need for custom adaptations and helps maintain reliable clamping under routine operational stresses. For compatibility checks or to secure the correct TECWERK M12 component for a 27 mm toolholder, contact Metav Werkzeuge for tailored advice and ordering support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000834074NW Product: Milling clamping screw Manufacturer: TECWERK Core data Thread: M12 Suitable for clamping diameter: 27 mm Overall length (L): 22 mm Head diameter (D): 35 mm Head height (K): 8 mm Pack unit: 1 Special features Conforms to DIN 6367 Compact design for confined tool pockets FAQ What thread does the clamping screw use? The clamping screw uses an M12 thread as specified for the TECWERK milling clamping screw (SKU 2000834074NW). Which clamping diameter is the screw intended for? The component is specified for a clamping diameter of 27 mm, matching standard toolholders that accept this interface. What are the key dimensions to check before installation? Check the overall length 22 mm, head diameter 35 mm and head height K 8 mm to ensure clearance and correct seating in the holder. Does the screw meet an industrial standard? Yes, the screw is manufactured to DIN 6367, supporting interchangeability and documented quality requirements. Is material information provided for corrosion or lubrication considerations? Material is not specified in the provided data; it is recommended to confirm material and surface treatment requirements prior to use. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com