messschieber
Das hier ist der erste PLatzhalter
200 mm Digital Spirit Level 0.02 mm/m, Tilt Direction Bar Rotatable Readout, Cast Iron Frame - Metav IndustryLine
Benefit from robust construction and precise digital measurement: the 200 mm spirit level combines a cast-iron frame with a rotatable digital readout and a fine 0.02 mm/m slope resolution for repeatable alignment results. Order the Digital spirit level M215.301 directly via Metav Werkzeuge or ask our consultants if further specification advice is required. M215.301 Digital spirit level — 200 mm, cast-iron frame, rotatable digital display A M215.301 Digital spirit level for precise angle and slope measurement in workshops, assembly and installation tasks Digital display with On/Off, M and HOLD buttons Cast-iron frame for high stability Resolution 0.02 mm/m for precise slope checks Angular accuracy 0.002° for fine alignment Reliable readings for accurate alignment The instrument delivers measurably better alignment thanks to a digital display that shows readings in degrees or in mm/m, making comparative levelling and setting slopes straightforward. With a resolution of 0.02 mm/m and an angular reading granularity of 0.001°, the unit supports fine adjustments where millimetre-level gradients matter. The stated angular accuracy of 0.002° translates into consistent orientation checks on machine set-ups and installation frames, reducing rework and alignment time. Explanations of units: mm/m expresses vertical deviation per metre run, while degrees indicate absolute inclination. Stiff frame reduces measurement variability Built around a cast-iron frame, the level resists flex and vibration that would otherwise introduce measurement error, particularly on longer spans or heavier fixtures. The robust construction contributes to a total weight of 1.6 kg, offering a stable contact surface without becoming cumbersome for site work. The compact overall dimensions (200 x 50 x 60 mm) balance reach and rigidity so the tool sits flat and reproducible on machined faces and installation rails, helping to preserve measurement integrity across repeated checks. Practical controls and site-ready display Operation is kept efficient through the simple control set: On/Off plus M and HOLD for memory or freezing a reading. The rotatable readout simplifies viewing when the level is used in different orientations, and the integrated tilt direction bar provides rapid visual confirmation of slope direction before fine digital adjustments are made. Power is supplied by 3x AAA batteries, which are widely available and easy to replace, minimizing downtime between jobs. The display mode selection between degrees and mm/m supports compatibility with different engineering workflows. Where this level fits into a production workflow Designed for workshops, maintenance teams and fitters, the device is classed among professional angle measuring instruments for everyday industrial use. It is suitable for machine set-up, conveyor alignment, frame and fixture levelling, and other tasks where reliable incline measurement is required without the complexity of larger digital inclinometers. The compact footprint makes it convenient for bench and on-site checks while the solid frame ensures durability in an industrial environment. Delivered with established Metav IndustryLine quality assurance, the level is positioned as a dependable measuring partner for standard and precision tasks. Choose the Metav IndustryLine spirit level for dependable alignment work and contact Metav Werkzeuge in Emmerich for tailored technical advice by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M215.301 GTIN: 4054469184692 Manufacturer: Metav IndustryLine SKU: M215.301 Facts Total length: 200 mm Dimensions: 200 x 50 x 60 mm Weight: 1.6 kg Measurement range: 0–90° / 999.99 mm Resolution (slope): 0.02 mm/m Angular reading: 0.001° Angular accuracy: 0.002° Power: 3x AAA batteries Digital display with On/Off, M and HOLD Special features Cast-iron frame Rotatable readout Tilt direction bar Readout in degrees or mm/m Category: Angle measuring instruments FAQ How is slope shown and what units are available? The level provides readings both in degrees and in mm/m; the M215.301 can be switched between units on the digital display to match the measurement convention required for the task. What accuracy and resolution can be expected for fine adjustments? The instrument offers a resolution of 0.02 mm/m and an angular reading of 0.001°, with an angular accuracy of 0.002°, suitable for precise alignment and installation tasks. Is the display usable in tight positions or rotated orientations? Yes, the M215.301 features a rotatable readout and a tilt direction bar to ensure legible results and quick orientation checks even in confined mounting situations. What powers the unit and how easy is battery replacement? Power is supplied by three AAA batteries; replacement is straightforward and uses commonly available cells to reduce interruption during on-site work. Which environments and tasks are most suitable for this instrument? This digital spirit level is intended for workshop alignment, machine set-up, fitting and installation tasks where reliable angle and slope measurement supports quality and repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Internal Spring Compass, Hardened Steel, DIN 6487 - Metav IndustryLine
Take advantage of the combination of hardened steel construction, DIN 6487 conformity and a 200 mm reach for consistent internal scribing and layout work; order the spring‑loaded internal probe directly via Metav Werkzeuge or consult our specialists for application advice. Spring‑loaded internal probe, 200 mm (Metav IndustryLine) — hardened steel, DIN 6487 compliant The Spring‑loaded internal probe, 200 mm is a spring-mounted internal measuring probe designed for precise internal scribing and layout tasks in metalworking and toolmaking applications. Hardened steel construction 200 mm reach for internal layout Conforms to DIN 6487 Spring‑loaded contact for stable marking Consistent internal marking for repeatable workflows The spring‑mounted contact provides a steady contact force, ensuring repeatable internal scribing across multiple components. With a clear 200 mm span, this probe is sized to reach deeper bores and larger internal diameters than shortpoint compasses, while maintaining the control expected in layout work. The spring mechanism reduces the risk of point bounce during rotation, which improves centreline accuracy and reduces rework. As a simple mechanical solution, it combines low complexity with dependable performance, making it suitable for task lists where consistent geometry transfer is required. Robust build and standards for long service life Constructed from hardened steel and manufactured to the requirements of DIN 6487, this probe is specified for durability under workshop conditions. Hardened material and a compact design reduce wear at the contact point and maintain geometry even with frequent use. Compliance with DIN 6487 offers a clear technical reference for procurement and quality assurance, supporting integration into inspection routines and drawings. The solid construction minimises deformation during handling, which preserves the original alignment and contributes to long‑term measurement stability. Practical handling and application versatility The spring action facilitates controlled one‑hand operation and smooth engagement with internal features, helping to speed layout and scribing tasks without sacrificing precision. This accessory is tailored to use with compasses and divider setups where an internal probing point is required for circle or bore marking, making it a practical addition to toolrooms, maintenance shops and production benches. The straightforward design also simplifies maintenance and replacement: fewer moving parts mean less downtime and consistent readiness for layout operations. Contact Metav Werkzeuge for specific application guidance and reliable supply of Metav IndustryLine spring‑loaded internal probes. Technical data Article number: M214.812 GTIN: 4054469183138 ECLASS: 21170336 Category: Compass (Zirkel) Facts Overall length: 200 mm Brand: Metav IndustryLine Special features Material: hardened steel Standard: DIN 6487 Function: spring‑loaded internal probe for scribing and layout FAQ What is the primary purpose of this probe? The Spring‑loaded internal probe is intended for internal scribing and layout tasks in metalworking and toolmaking, providing a spring‑mounted contact for repeatable internal markings. Which standard does the product meet? This Metav IndustryLine probe complies with DIN 6487, ensuring it meets recognised workshop and procurement specifications. What material is the probe made from? The probe is manufactured from hardened steel, giving wear resistance and dimensional stability under normal workshop use. Can this probe be used with standard compass setups? Yes, the probe is designed as an accessory for compass/divider arrangements where an internal probing or scribing point is required; compatibility should be checked against the specific compass model. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Scratch Gauge With Marking Holes, 5–160mm Range, 1mm Pitch - Metav IndustryLine
Take advantage of a durable, low-weight design combined with precise, repeatable scribing: aluminium construction with a black anodised finish and a fine 1 mm pitch ensure accurate layout over the full 200 mm length. Order the marking gauge directly via Metav Werkzeuge or ask our consultants if needed. Marking Gauge M203.044 — aluminium scribing gauge, 200 mm, with scribing holes (Metav IndustryLine) The Marking Gauge M203.044 is an aluminium scribing gauge with an integrated stop and an array of scribing holes, designed for precise and repeatable layout work across metal and workshop applications. *Aluminium black anodised finish *200 mm overall length *Scribing holes 5–160 mm range *Fine 1 mm pitch for repeatable marks Precise scribing for reproducible layout work This scribing gauge delivers repeatable marks thanks to its fine 1 mm pitch adjustment and clear hole spacing from 5 to 160 mm. The engraved pitch allows for incremental, measurable steps when transferring dimensions, reducing reliance on manual estimation and minimising layout errors. As a result, time spent reworking parts is reduced and first-pass quality improves—an important efficiency gain in small-batch production and maintenance tasks. The robust indexing of the scale ensures consistent marks even under frequent use, supporting reliable production flows. Built to withstand the workshop environment Constructed from black anodised aluminium, the tool combines low weight (approx. 0.2 kg) with good corrosion resistance and a tactile, non-reflective surface that eases reading in bright lighting. The integrated stop (100 x 30 mm) provides a stable reference face for straight scribing along edges or templates, improving angle control and alignment. The lightweight design keeps operator fatigue low during extended marking tasks while preserving sufficient stiffness for accurate lines on both metal and timber substrates. Flexible marking options for a range of components The array of scribing holes (spacing covering 5–160 mm) enables rapid transfer of repeat distances and the creation of parallel scribed lines without recalibrating the tool. Combined with the 200 mm overall reach, this gauge suits small to medium components where controlled offsets are required, such as flanges, brackets and templates. The clear, graduated pitch simplifies repositioning and lowers the cognitive load when performing repetitive layout operations, improving throughput on both workshop benches and assembly stations. Simple integration into quality-oriented workflows As a compact layout instrument, this gauge complements measurement and inspection equipment without the need for complex setup. The design supports quick hand-held operation and can be used alongside calipers, squares and templates to establish datum lines before machining or welding. Backing from Metav IndustryLine ensures availability and compatibility with common workshop routines, and the product specification (including SKU M203.044 and GTIN 4054469183329) enables straightforward inventory management and traceability for procurement records. For consistent and efficient marking results, consult Metav Werkzeuge’s product specialists in Emmerich for tailored advice and fast delivery options — Metav Werkzeuge supports specification and procurement for industrial workshops Technical Data Article number: M203.044 GTIN: 4054469183329 Material: Aluminium, black anodised Overall length: 200 mm Weight: 0.2 kg Pitch: 1 mm Stop dimension: 100 x 30 mm Scribing holes range: 5–160 mm Facts Length: 200 mm Weight: 0.2 kg Hole range: 5–160 mm Pitch increments: 1 mm GTIN: 4054469183329 Special features Integrated stop for edge reference Black anodised finish for wear resistance Lightweight aluminium construction Array of scribing holes for repeat distances FAQ What materials is this scribing gauge suitable for? The marking gauge M203.044 is made from aluminium with a black anodised finish and is suitable for layout work on metals and common workshop materials where a durable, low-weight gauge is required. How precise are the pitch increments on the tool? The gauge features a 1 mm pitch, enabling reproducible incremental marking and simple transfer of measured steps without guesswork. Can the tool produce parallel lines or repeat distances quickly? Yes, the integrated array of scribing holes (5–160 mm range) allows the user to transfer repeat distances and create parallel scribed lines efficiently. Is the product easy to store and identify in inventory? The item is identified by SKU M203.044 and GTIN 4054469183329, which supports straightforward ordering and stock control in workshop inventories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Spring External Divider Hardened Steel, DIN 6487 - Metav IndustryLine
Take advantage of a hardened steel construction together with DIN 6487 conformity and a precise 200 mm measuring length for dependable external gauging in everyday workshop use. Order the component via Metav Werkzeuge or consult our advisers for application-specific guidance. Spring-Loaded External Caliper M214.802 — 200 mm, hardened steel (DIN 6487) | Metav IndustryLine The Spring-Loaded External Caliper M214.802 is a compact, spring-actuated tool designed for precise external measurements in metalworking and general workshop applications Spring-actuated jaw movement for consistent contact Hardened steel construction for long service life Conforms to DIN 6487 for reliable standard compliance 200 mm measuring length for common workshop tasks Consistent contact for reliable external measurements The spring-loaded mechanism provides a defined contact action that reduces variance caused by manual pressure, improving repeatability for routine external measurements. Conformance with DIN 6487 ensures the tool meets recognised dimensional standards, making it suitable for use in inspection benches and production checks. The 200 mm span balances reach and rigidity so that measurements of shafts, collars and housings remain reproducible without sacrificing handling. Built to withstand workshop demands Constructed from hardened steel, this caliper is designed for robust use where resistance to wear and mechanical stress matters. The material choice increases resistance to abrasion and retains jaw geometry over time, which translates into fewer recalibrations and lower life‑cycle costs. As a simple, maintenance-friendly instrument, it complements standard measuring sets in machining and maintenance departments where reliability and quick turnarounds are priorities. Quick handling and practical integration The spring action allows fast, single‑handed operation for gauging external diameters and distances, supporting efficient workflow during repetitive tasks. Its straightforward design enables easy cleaning and inspection; parts subject to wear can be checked and replaced without complex procedures. Supplied as a workshop-ready instrument, it integrates seamlessly into standard tooling kits and supports consistent quality checks across small-batch production or repair workspaces. For tailored advice or to secure supply from Metav Werkzeuge in Emmerich, contact our specialists who can confirm suitability for the intended application and delivery options Technical Data Article number: M214.802 GTIN: 4054469183091 Material: hardened steel Standard: DIN 6487 Facts Overall length: 200 mm Special features Spring-loaded jaw movement Category: compass / caliper tool Brand family: Metav IndustryLine FAQ What is the main advantage of the spring-loaded mechanism? The spring-loaded external caliper delivers a consistent contact force, which improves reproducibility of external measurements and reduces operator-related variation. Is the material suitable for regular workshop use? Yes, the hardened steel used for this caliper ensures wear resistance and long-term retention of jaw geometry, making it well suited to frequent use in machining environments. Which standard does the caliper comply with? The instrument is manufactured to DIN 6487, providing assurance that dimensional and design criteria meet established industrial norms. Can this caliper be used for measuring shafts and collars? The 200 mm measuring length and spring-actuated jaws make it appropriate for measuring external diameters such as shafts, collars and housings in general workshop and maintenance tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Digital Caliper Angled Jaw Fine Adjustment 0.08mm Accuracy, Data Output RB5, Stainless Steel, Case - Metav IndustryLine
A robust combination of fully hardened stainless steel construction and a fine-adjustment thumbwheel ensures repeatable readings and safe handling of small workpieces, while the 250 mm measuring range and factory accuracy of Werksnorm 0.08 mm make it suitable for standard workshop tasks; order the Digital Caliper with Angled Jaw directly via Metav Werkzeuge or ask our consultants if needed. Digital Caliper with Angled Jaw, 250 mm — Stainless, Fine-Adjustment (Metav IndustryLine) The Digital Caliper with Angled Jaw is a 250 mm stainless steel measuring instrument with an angled jaw and fine-adjustment mechanism, designed for precise measurements in confined or angled workspaces. Fully hardened stainless steel construction Fine-adjustment thumbwheel for precise positioning 0.01 mm / 0.0005" resolution display RB 5 data output for digital integration Durable stainless design for dependable shop-floor measurements The caliper combines a fully hardened stainless steel beam and slide for long-term wear resistance and corrosion stability, which reduces drift in regular use and maintenance. With a 250 mm measuring range the instrument falls into the workshop standard category (best balance of reach and stiffness), delivering reliable performance for routine machining and inspection tasks. The listed factory accuracy of Werksnorm 0.08 mm represents the controlled tolerance applied during manufacture; this should be seen alongside the finer display resolution when assessing measurement capability. Fast, auditable digitisation for quality workflows Equipped with a digital display offering 0.01 mm (or 0.0005") resolution, the device supports common functions such as mm/inch toggle, zero/absolute, hold, tolerance and preset to speed up inspections and reduce manual transcription errors. The integrated RB 5 data output enables direct transfer of readings into statistical process control systems or measurement logs, simplifying traceability and supporting lean quality processes. These features together deliver a measurable productivity gain for batch checks and documentation-heavy tasks. Fine adjustment and angled jaw for precision in tight spaces The fine-adjustment thumbwheel provides controlled jaw travel, preventing overshoot and improving repeatability when measuring small steps or delicate features. The angled jaw (50 mm jaw length) opens access to narrow bores and shoulder features where straight jaws struggle, allowing safer contact and clearer sightlines. Ergonomic enhancements and a balanced mass (approx. 0.8 kg) make the instrument comfortable for repeated use and reduce operator fatigue during medium-length inspection routines. Clear distinction between resolution and usable accuracy It is important to distinguish resolution from accuracy: while the display shows values to 0.01 mm, the declared factory tolerance (Werksnorm 0.08 mm) indicates the expected measurement deviation under standard conditions. For traceable calibration, Metav supplies instruments from a controlled supply chain and can advise on service intervals to maintain consistency. This caliper's combination of practical resolution, workshop-grade robustness and data output capability positions it as an efficient tool for standard machine-shop metrology and incoming inspection processes. For configuration, ordering or technical advice on Metav IndustryLine measuring tools, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — assistance is available to match the instrument to specific inspection tasks. Technical data Article number: M240.058 Manufacturer: Metav IndustryLine Material: Stainless steel Measuring range: 250 mm Numbers / Core technical data Resolution: 0.01 mm / 0.0005" Factory accuracy (Werksnorm): 0.08 mm Jaw length: 50 mm Power / measurement system: 3 V Weight: 0.8 kg Designs / Special features Fully hardened construction Fine-adjustment thumbwheel Angled jaw for confined spaces Buttons: On/Off, mm/inch, 0/Abs, Hold, Tol, Preset Data output: RB 5 FAQ Is the caliper suitable for everyday workshop use? The Digital Caliper with Angled Jaw from Metav IndustryLine is designed as a standard workshop instrument with a 250 mm range, balancing reach and stiffness for routine machining and inspection operations. What is the difference between the display resolution and the device accuracy? The display resolution is 0.01 mm (0.0005"), while the declared factory tolerance for the instrument is Werksnorm 0.08 mm; the latter describes expected measurement deviation under normal conditions and should guide decisions on suitability for precision tasks. Can measurement data be exported to a PC or SPC system? Yes, the caliper features an RB 5 data output that enables direct transfer of readings into compatible data-collection or SPC systems for traceability and statistical evaluation. Does the angled jaw improve accessibility for specific components? The angled jaw, with a 50 mm length, enhances access to narrow bores, shoulders and other confined geometries where straight-jawed calipers are difficult to position; this reduces handling time and the risk of incorrect contact. Are common measurement functions available on the display? The instrument includes standard digital functions such as mm/inch conversion, zero/absolute, hold, tolerance display and preset, which aid rapid checks and reduce manual calculation errors. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Outer Measuring Jaw For Digital Carbon Fibre Caliper, For 8mm Jaw Thickness - Metav IndustryLine
Take advantage of the combination of lightweight construction and precise contact geometry for dependable external measurements; compatibility with standard digital universal calipers ensures straightforward workshop integration. Order the accessory via Metav Werkzeuge or consult our specialists for application-specific advice. M217.364.3 — Carbon-fibre external measurement jaw for digital universal calipers (8 mm jaw thickness) — Metav IndustryLine The M217.364.3 is a purpose-built external-measurement jaw intended for digital universal calipers, combining low thermal expansion and robust contact geometry to support consistent dimensional control in workshop and production environments. Carbon fibre construction for low thermal drift Designed for digital universal calipers Compatible with 8 mm jaw thickness Lightweight: only 0.2 kg for easy handling Precise external measurement with reduced thermal influence The carbon-fibre construction delivers a low thermal expansion coefficient and a high stiffness‑to‑weight ratio, which together improve measurement repeatability during temperature changes common in production halls. Fitted to a caliper head, the accessory preserves the instrument’s metrology characteristics while reducing operator‑induced variability. The combination of precision contact surfaces and minimal mass means less inertia during handling, contributing to faster, more reliable checks in serial processes. Smooth integration into digital caliper workflows Designed for compatibility with digital universal calipers, the jaw attaches to calipers with a jaw thickness of 8 mm, allowing quick retrofitting without modification of existing measuring equipment. This adaptability reduces downtime and simplifies tool management in the workshop, supporting lean measurement routines and faster cycle times. The lightweight design also lessens operator fatigue during repetitive checks, so throughput and consistency improve with minimal process change. Robust design for everyday workshop reliability While optimised for external measuring tasks, the jaw’s geometry and materials handle frequent handling and typical workshop conditions without compromising contact accuracy. The compact width and engineered contact faces help protect the mating surfaces against deformation, ensuring sustained repeatability over many inspection cycles. Backed by Metav’s quality approach and logistics in Emmerich, the accessory forms part of a pragmatic system that brings industrial‑grade measurement closer to everyday workshop use. Contact Metav Werkzeuge to discuss fitting options for the Metav IndustryLine M217.364.3 and to confirm compatibility with existing calipers Technical data SKU: M217.364.3 Manufacturer: Metav IndustryLine Material: Carbon fibre Suitable for calipers with jaw thickness: 8 mm Application: External and internal measurement Key numbers Width: 16 mm Weight: 0.2 kg Measurement range (as labelled): 0‑X/20‑X Special features Designed for digital universal calipers Low thermal expansion for stable results Lightweight for reduced operator fatigue Engineered contact geometry for repeatability FAQ Which calipers are compatible with this jaw? The M217.364.3 from Metav IndustryLine is designed for use with digital universal calipers that accept a jaw thickness of 8 mm; confirmation of the caliper jaw profile is recommended before fitting. Can this jaw be used for internal measurements as well as external ones? Although intended primarily as an external‑measurement accessory, the jaw’s geometry allows adaptability to related tasks; the M217.364.3 performs best when mounted on calipers configured for the specific measurement type. How does the carbon‑fibre construction benefit shop measurements? Carbon fibre offers low thermal expansion and high stiffness at low mass, so the M217.364.3 helps maintain measurement stability during temperature fluctuations and reduces handling inertia for more consistent readings. What is the handling weight and why does it matter? At approximately 0.2 kg, the accessory is lightweight, which reduces operator strain during repetitive checks and contributes to faster, steadier measurement cycles. Is the accessory suitable for heavy production use? The accessory is crafted for regular workshop and production environments; its contact geometry and material choice are intended to provide durable, repeatable performance under normal operating conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Hier wird noch anderes html hinkommen um das wir uns später kümmern