1.5 kN Horizontal Foot Clamp With Silicone‑Coated Handle, 50mm Thread Length, Stainless Steel - Kukamet

Take advantage of a compact, corrosion-resistant clamp that combines high clamping and holding forces with a non-slip, silicone-coated grip for dependable fixture retention. Order the component directly via Metav Werkzeuge or consult the Metav team for specification support.

Toggle Latch Clamp 361 by Kukamet — horizontal mounting foot, stainless steel

The Toggle Latch Clamp 361 is a stainless steel toggle clamp designed for secure fastening of covers, fixtures and removable panels in workshop and industrial assemblies.

• Stainless steel construction for corrosion resistance
• Silicone-coated handle for secure grip
• Horizontal mounting foot for flush installation
• 1,500 N clamping force, 1,725 N holding force

Dependable clamping where precision matters

Built for repetitive use in production and assembly environments, this stainless steel toggle latch delivers measurable performance: a clamping force of 1,500 N and a holding force of 1,725 N, values that translate into secure retention under dynamic loads. The metal grade supports consistent duty cycles and reduces the risk of deformation, while the quantified force figures provide a reliable basis for fixture design and quality assurance. This makes the clamp suitable for jigs, access panels and removable fixturing where repeatable clamping behaviour is essential.

Rapid mounting and ergonomic operation

The horizontal mounting foot allows flush installation, saving space on worktops and within assemblies. A silicone-coated handle improves manual control during engagement and release, reducing slippage and operator fatigue over long shifts. The component features a thread length 50 mm for secure attachment and fine adjustment during setup; the integrated hook provides positive latching without additional hardware. These design choices support fast cycle times and minimise the effort needed for regular tool changes or maintenance operations.

Low-maintenance durability for workshop use

A compact design with a weight of approximately 0.1 kg combines structural robustness with minimal mass, avoiding unnecessary load on moving fixtures. The corrosion resistance of the stainless steel body reduces upkeep and extends service intervals, contributing to lower total cost of ownership in corrosive or humid environments. Simple geometry and accessible fastenings allow basic inspection and replacement without specialist tooling, so maintenance routines remain efficient while production uptime is preserved.

For specification advice or to secure the Kukamet toggle latch clamp S361-2-K for reliable, corrosion-resistant clamping, contact Metav Werkzeuge for tailored guidance and order facilitation.

Technical data

• Article number: S361-2-K
• GTIN: 8680731509533
• Manufacturer: Kukamet

Facts

• Clamping force: 1,500 N
• Holding force: 1,725 N
• Thread length: 50 mm
• Weight: 0.1 kg
• eCl@ss: 21041718
• ETIM: EC011973

Special features

• Material: stainless steel
• Mounting: horizontal foot
• Handle: silicone-coated
• Includes hook
• Category: toggle clamp / latch clamp

FAQ

What types of fixtures is this clamp suited for? The Kukamet toggle latch clamp S361-2-K is suitable for removable covers, jigs and panels where a horizontal, flush-mounted retention solution is required.

Can the clamp be used in humid or mildly corrosive environments? Yes, the stainless steel body of the S361-2-K provides enhanced corrosion resistance, making it appropriate for damp workshop conditions and many industrial settings.

How is the clamp mounted and adjusted? Mounting uses the horizontal foot; adjustment is achieved via the threaded connection with a thread length of 50 mm, allowing precise alignment during installation of the latch.

Is the handle suitable for repetitive manual operation? The silicone-coated handle improves grip and operator comfort during frequent engagement and release cycles, reducing slippage and fatigue.

What are the measurable holding characteristics of the clamp? The clamp provides a clamping force of 1,500 N and a holding force of 1,725 N, values intended for integration into fixture load calculations.

Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com