SPMG 050204 Indexable Insert for Stahl - MetavCUT

Take advantage of a robust, high-capacity milling solution that pairs efficient material removal with secure clamping and proven indexable insert compatibility; the combination of a 63 mm cutting diameter, 8 cutting edges and a 32 mm shank supports continuous workshop production with predictable results — contact Metav Werkzeuge for procurement or technical clarification. T-slot cutter TKC052TM — 63 mm diameter, 8 cutting edges (Teknik Makina) T-slot cutter TKC052TM for machining T-slots and grooves in standard milling setups, designed for indexable inserts and stable mounting in typical toolholders 63 mm diameter for wide T-slots 8 cutting edges for rapid material removal Compatible with SPMG 05 indexable inserts 32 mm shank for secure toolholder clamping Fast, stable machining thanks to balanced cutting geometry The milling head delivers high removal rates through its 8 cutting edges, which distribute cutting forces and reduce vibration during slotting operations. This geometry enables a consistent chip flow and helps maintain surface finish while shortening cycle times. The 63 mm outer diameter provides sufficient clearance for most standard T-slot profiles, while the moderate overall length of 120 mm keeps run-out low in the toolholder. Where indexable inserts are used, changeover is quick and repeatable, reducing downtime in batch or series production. Secure clamping and simple insert management for workshop efficiency A 32 mm shank ensures robust clamping in conventional toolholders and reduces the risk of movement under load, supporting stable cutting even at higher feed rates. The cutter accepts SPMG 05 indexable inserts (compatible with Taegutec), which simplifies inventory and allows selection of grade and coating to match the workpiece. Insert clamping employs M2x4.2 Torx screws and a T6 key, enabling reliable fixation with standard workshop tools; this arrangement reduces the chance of incorrect seating and speeds up maintenance cycles. Application fit and predictable performance for mixed machining tasks With a cutting height of 5 mm and a cutting length of 45 mm on the shaft, the tool is suited to producing shallow to medium-depth T-slots and finishing passes where dimensional control matters. The unit weight of 0.861 kg reflects a solid construction that resists deflection, supporting repeatable results in steel and lighter alloys when used within recommended parameters. For process planning, the tool’s compatibility with common indexable insert formats allows selection of coatings and grades to match throughput and surface requirements, so process engineers can balance productivity and tool life effectively. Should clarification be required, Metav Werkzeuge’s technical advisors are available to support selection and integration. Contact Metav Werkzeuge for tailored advice on tooling choices and to arrange supply of the Teknik Cutting Tools T-slot cutter TKC052TM for reliable workshop integration — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TKC052TM Manufacturer: Teknik Cutting Tools (Teknik Makina) Product name: T-slot cutter TKC052TM Compatible insert type: SPMG 05 Compatible insert supplier: Taegutec Dimensions & core data Diameter: 63 mm Cutting edges: 8 Overall length: 120 mm Shank diameter: 32 mm Cutting length on shaft: 45 mm Cutting height: 5 mm Weight: 0.861 kg Special features Torx screw for inserts: M2x4.2 Torx key size: T6 Indexable-insert system for fast changeover Balanced multi-edge configuration for vibration control FAQ Which insert type fits this cutter? The cutter is designed for SPMG 05 indexable inserts; compatible grades from Taegutec can be used for different materials and surface requirements. What diameter and shank size does the tool have? The tool has a 63 mm cutting diameter and a 32 mm shank, providing stable clamping in common toolholders for routine milling operations. How many cutting edges are available and what is the benefit? With 8 cutting edges, the tool offers distributed cutting forces for smoother operation and efficient material removal during T-slot milling. What fastening hardware is required for the inserts? Insert clamping is secured with M2x4.2 Torx screws tightened with a T6 key for reliable and repeatable seating. Is the cutter suitable for deep T-slots? The cutter provides a cutting height of 5 mm and a shaft cutting length of 45 mm; it is optimised for shallow to medium-depth T-slots and finishing passes rather than very deep profiles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise T-slot geometry, robust 32 mm shank support and rapid indexable-insert replacement for uninterrupted production. Order the T‑slot cutter directly via Metav Werkzeuge or request advice from the technical consultants for tailored application guidance. T‑nut cutter TKC050TM — 50 mm diameter, 7‑flute T‑slot milling cutter by Teknik Makina The T‑nut cutter TKC050TM is a purpose‑built tool for accurate T‑slot and T‑nut machining in general workshop and industrial milling applications, designed to deliver repeatable slot geometry with quick insert changes. 50 mm diameter for wide T‑slots 7 flutes for stable chip control 32 mm shank for rigid clamping 45 mm cutting length for deep slotting Consistent slot geometry for reliable assembly This T‑slot mill is engineered to produce precise T‑slot profiles with a stable cutting edge arrangement. The combination of a 50 mm diameter and 7 flutes reduces vibration and promotes uniform chip evacuation, which in turn helps maintain profile accuracy over serial runs. For customers seeking repeatable fitting results in fixtures and workholding, the tool’s balanced flute count offers an effective compromise between surface finish and removal rate. The cutting head is secured with a Torx fastener system to simplify insert replacement, while the robust 32 mm shank supports high clamping rigidity and reduces the risk of runout during heavy passes. Optimised for productivity and straightforward insert servicing Designed with workshop efficiency in mind, the tool supports rapid insert changes and minimal downtime. The cutter is supplied with a Torx screw (M2x4.2) and requires a T6 Torx key, ensuring secure and fast replacement of indexable inserts from compatible manufacturers. With a 45 mm cutting length and a 5 mm cutting height, the tool is suitable for moderately deep T‑slot operations without compromising stability. The overall length of 120 mm and a relatively low mass (0.83 kg) make the cutter easy to handle during tool changes and storage, while still providing the necessary reach for most vertical and horizontal milling setups. Material compatibility and application profile The cutter’s geometry and construction make it suitable for a broad range of general metalworking tasks where T‑slot milling is required. Its flute geometry aids chip control across typical ferrous and non‑ferrous workpieces commonly encountered in fixture manufacture and machine bed modification. Compatibility with established insert manufacturers, including Taegutec, simplifies procurement and gives access to a range of grades for different materials and cutting conditions. The result is a tool that supports both one‑off and small‑batch production environments with a focus on consistent fit and reduced rework. Installation, handling and expected benefits Fitted into a suitable toolholder with the 32 mm shank, the cutter performs best when clamped with minimal overhang and correct axial support. The indexed insert system means that minor edge wear can be addressed by simple indexing or replacing the insert, avoiding full‑tool replacement and lowering operating costs. Users will appreciate the balance between cutting capacity and user‑friendly maintenance: faster changeovers and fewer interruptions translate into improved shop throughput and predictable part quality. Documentation and technical drawings are recommended for integration into process planning and NC programming. For technical consultation on integrating the 50 mm T‑slot cutter into production, contact Metav Werkzeuge for expert advice and dependable delivery from Emmerich. Technical data Article number: TKC050TM Manufacturer: Teknik Makina ECLASS: 21180605 ETIM: EC011860 Core data Diameter: 50 mm Flutes: 7 Overall length: 120 mm Shank diameter: 32 mm Cutting length (shank): 45 mm Cutting diameter at shank: 31.5 mm Cutting height: 5 mm Weight: 0.83 kg Special features T‑slot cutter for machining T‑nuts and T‑slots Compatible with Taegutec indexable inserts Torx screw M2x4.2 for insert clamping Torx key required: T6 SKU: TKC050TM FAQ Which insert brands fit this T‑slot cutter? The TKC050TM is specified for use with compatible indexable inserts; it is listed as compatible with Taegutec inserts and will accept inserts from manufacturers following the same seat geometry. What shank size and holder are required? The cutter has a 32 mm shank; a rigid toolholder sized for a 32 mm shank and minimal overhang is recommended to ensure optimal runout and finish. How deep can the cutter machine a T‑slot in one pass? The tool provides a 45 mm cutting length and a 5 mm cutting height; maximum single‑pass depth should be selected based on material, insert grade and machine rigidity to avoid overload. How is the insert secured and replaced? Inserts are secured with a Torx screw (M2x4.2) and require a T6 Torx key for removal and fitting, enabling quick and secure insert changes. Is the TKC050TM suitable for serial production? Yes, the cutter’s multi‑flute design and robust shank support are intended to deliver consistent results in serial and small‑batch production, reducing rework and downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com