Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
9.28mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of ultra‑fine tolerance and workshop‑grade robustness for reliable end‑measure checks; the precision and repeatability help reduce rework and speed up inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin, single, 9.28 mm, ±0.001 mm — Metav IndustryLine The gauge pin, single, 9.28 mm, ±0.001 mm, length 50 mm is a compact inspection pin designed for micro‑range end‑measure verifications in workshop and metrology workflows Workshop‑grade construction Tolerance ±0.001 mm for high precision Diameter 9.28 mm, length 50 mm Made from special steel for durability Precision tailored to micro components This compact inspection pin belongs to the micro class of measuring tools, intended for measurement ranges up to 100 mm where minimal flex and maximum accuracy are essential. Manufactured for fine end‑measure checks, the pin delivers a tolerance of ±0.001 mm, which corresponds to sub‑micrometre control useful in high‑precision jigs, small bearing bores and tight‑tolerance assemblies. The extremely small allowance limits measurement uncertainty and makes the component suitable for quality gates where reproducible results are required. By specifying such narrow tolerance, inspection throughput is improved because fewer ambiguous readings require repeat measurement or rework. Durable construction for repeated workshop use Produced in special steel and finished for workshop conditions, the inspection pin combines hardness with wear resistance to sustain frequent insertion checks. The 50 mm length and 9.28 mm diameter offer a stable handling length while limiting deflection during use; this balance supports fast, repeatable checks without complex fixturing. The workshop version is engineered to withstand routine handling and maintains dimensional integrity across repeated cycles, extending service intervals and lowering lifecycle cost compared with softer, untreated pins. Robustness here means predictable performance on the shop floor and consistency between inspection runs. Integrating into inspection routines and quality control As a single gauge pin for end‑measure verification, this tool is ideal for checking bore sizes, verifying jig clearances and confirming final dimensions on small parts. The simple geometry enables easy use with comparators, height gauges or as a reference in assembly checks. Incorporating such a precision pin in the inspection plan reduces decision time at the control station and supports lean processes by preventing downstream rejects. The component’s clear specification streamlines documentation and traceability in quality records, helping to align shop‑floor practice with formal inspection criteria. For precise end‑measure checks, request the Metav IndustryLine gauge pin M323.928 from Metav Werkzeuge — contact Metav Werkzeuge GmbH in Emmerich for product advice and ordering support Technical data Article number: M323.928 GTIN: 4061905061912 Manufacturer: Metav IndustryLine Measurements Diameter: 9.28 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.03 kg Special features Workshop execution Material: special steel Single gauge pin for end‑measure inspections Category: gauge pins / inspection pins FAQ What accuracy can be expected from this gauge pin? The gauge pin M323.928 from Metav IndustryLine is specified at ±0.001 mm, offering sub‑micrometre control suited to high‑precision end‑measure checks. For which applications is the pin most suitable? This inspection pin is intended for micro‑range verifications such as bore checks, jig validation and tiny assembly inspections where 9.28 mm diameter references are required. What material is the pin made from and why does that matter? The pin is made from special steel, chosen for hardness and wear resistance so that repeated use on the workshop floor preserves dimensional stability and repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.29mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of workshop‑grade robustness and laboratory‑level accuracy: the combination of a 9.29 mm diameter, ±0.001 mm tolerance and a stable 50 mm length ensures reliable end‑dimension checks and fewer inspection reworks. Order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test Pin M323.929 — single gauge pin with 9.29 mm diameter and ±0.001 mm accuracy The Test Pin M323.929 is a workshop‑grade gauge pin designed for precise end‑dimension inspection and verification in industrial metrology. Workshop version, robust construction Diameter 9.29 mm with ±0.001 mm accuracy 50 mm overall length for stable probing Supplied in protective transport case Precision that reduces rework and increases throughput The gauge pin delivers ±0.001 mm tolerance on a 9.29 mm diameter, enabling confident acceptance or rejection of finished parts in high‑accuracy production environments. With such fineness of control, inspection cycles become more decisive and repeatable, which reduces downstream rework and improves first‑pass yield. The measured tolerance is compatible with tight end‑dimension checking, making this pin suitable as a reference for comparative gauging and quick pass/fail assessments on the shop floor. Built to withstand workshop handling and assure measurement stability Constructed from special steel and finished as a workshop version, this inspection pin combines wear resistance with the rigidity required for repeatable measurements. Its 50 mm length provides a stable contact depth for end‑face probing while keeping handling straightforward; the low weight assists in fast fixture changes. Supplied in a transport case (plastic or wooden as required for safe transit), the pin remains protected between uses, reducing the risk of damage and preserving calibration intervals. Fits into traceable quality workflows and simple inventory management The design supports rapid identification and traceability within quality systems: item details such as SKU: M323.929 and GTIN: 4061905062575 allow straightforward stock control and integration into inspection logs. As a single gauge pin for end‑dimension verification, it complements existing plug and gauge sets or bespoke inspection fixtures, shortening setup time and harmonising routine checks. Metav’s distribution model adds a quality filter from Emmerich, offering dependable supply and documentation for workshop and production environments. For reliable end‑dimension control with Metav IndustryLine accuracy, contact Metav Werkzeuge in Emmerich for tailored advice and rapid supply: +49 2822 7131930 · info@metav-werkzeuge.com Technical data Label: Prüfstift, einzeln, 9,29mm, +/- 0.001 mm Länge 50 mm SKU: M323.929 GTIN: 4061905062575 Manufacturer: Metav IndustryLine Material: special steel Diameter: 9.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Workshop version, delivered in transport case Facts Diameter (mm): 9.29 Length (mm): 50 Tolerance (mm): ±0.001 Weight (kg): 0.03 Special features Workshop execution Suitable for end‑dimension inspection Supplied in plastic or wooden transport case GTIN for inventory and traceability FAQ What verification tasks is this gauge pin intended for? The Test Pin M323.929 is intended for end‑dimension checks and comparative gauging where a 9.29 mm reference and ±0.001 mm precision are required, e.g. final inspection of shafts, pins or bores. Can this pin be used in fixture or jig setups? Yes, the single gauge pin is suitable for fixture integration and reference probing; its 50 mm length provides stable engagement for many common jig geometries. How is the pin protected during storage and transport? The inspection pin is supplied in a protective transport case (plastic or wooden as required), which preserves the measuring surface and reduces the risk of handling damage. Is the material suitable for regular shop use? Manufactured from special steel, the pin is designed for repeated contact and workshop environments while maintaining dimensional stability under normal handling. How can the part be tracked in an inventory or quality system? Use the supplied identifiers — SKU: M323.929 and GTIN: 4061905062575 — to log the tool in stock systems and link it to inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.2mm Gauge Pin Single, ±0.001mm, Length 50mm, Special Steel, Workshop Version, Supplied In Case - Metav IndustryLine
Take advantage of the combination of laboratory‑grade accuracy, robust workshop design and ready‑to‑use transport protection for dependable end‑measurement checks. Order the test pin directly via Metav Werkzeuge or contact the consultants for application advice. Test pin M323.920 — Workshop test pin, 9.20 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A Test pin M323.920 designed for precise end‑measurement and gauge verification in workshop and inspection environments Workshop execution for robust shop use Diameter 9.20 mm with ±0.001 mm tolerance 50 mm overall length for gauge compatibility Supplied in protective transport case Precision that secures measurement reliability The inspection pin delivers exceptionally fine dimensional control with a certified tolerance of ±0.001 mm, making it suitable where repeatable end‑measurement is essential. The slim diameter of 9.20 mm combined with the 50 mm overall length provides a stable contact area for bore checks and reference gauges; this geometry minimises bending and ensures consistent contact forces during manual inspection. Emphasis on measurable accuracy supports quality control processes and reduces the risk of rejected parts in serial production. Durable construction for everyday workshop use Constructed from special steel, the pin is specified as a workshop version to withstand regular handling and integration into fixture plates, dial gauge holders or verification rigs. The material selection balances wear resistance with machinability, so the probe retains its dimensional integrity over repeated cycles. The proven robustness of the design reduces replacement frequency and supports uninterrupted inspection routines in demanding production environments. Practical handling and system compatibility With a 50 mm length, the test pin fits standard gauge blocks, plug gauges and many clamping arrangements without obstructing adjacent features. The compact form factor eases handling during batch inspections and makes mounting straightforward in common gauge fixtures. Where adapters or spacers are used, the pin’s nominal diameter and tight tolerance simplify traceability in measurement plans and permit direct comparison across measurement systems. Delivered ready for transport and storage The item is supplied in a protective transport case to safeguard the calibrated geometry during handling and transit — a practical detail that reduces the risk of accidental damage before it reaches the inspection bench. The workshop specification and protective packaging together support consistent performance from receipt to first use, simplifying logistics for procurement and quality teams. Contact Metav Werkzeuge today to request a suitability assessment for the Metav IndustryLine test pin M323.920 or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.920 GTIN: 4061905065057 Weight: 0.03 kg Material: Special steel Manufacturer: Metav IndustryLine Data Diameter: 9.20 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Category: Test pin / Gauge pin Special features Workshop execution Supplied in protective transport case Robust construction for regular use Suitable for end‑measurement and gauge verification FAQ What tolerance does the test pin offer and for which checks is it suitable? The test pin M323.920 provides a tolerance of ±0.001 mm and is suitable for precise end‑measurement, bore checks and gauge verification in workshop inspection routines. Which material is used for the probe and how does it affect durability? Manufactured from special steel, the M323.920 combines wear resistance with dimensional stability, ensuring long service life under regular handling in workshop environments. Is the test pin delivered protected for transport? Yes, the pin is supplied in a protective transport case to prevent damage to the measuring surface during storage and shipment. Can the pin be used in standard gauge fixtures and plug gauge setups? The 50 mm overall length and 9.20 mm diameter make the pin compatible with many common gauge holders and plug gauge arrangements for straightforward integration. Does the product come with manufacturer identification or a traceable article number? The item is listed under article number M323.920 and GTIN 4061905065057 for traceability and catalogue reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.31mm Gauge Pin ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
High-precision measurement and robust workshop design combine to keep inspection routines efficient and reproducible; the 9.31 mm gauge pin with ±0.001 mm tolerance and a 50 mm overall length delivers the dimensional certainty required for end‑measurement tasks. Order directly via Metav Werkzeuge or consult the Metav team for technical advice and application support. Gauge pin M323.931 — 9.31 mm, ±0.001 mm accuracy, 50 mm length (Metav IndustryLine) The Gauge pin M323.931 is a single precision test pin intended for end‑measurement applications, offering a nominal diameter of 9.31 mm with an accuracy of ±0.001 mm for repeatable plug and go inspection tasks High precision ±0.001 mm tolerance Nominal diameter 9.31 mm Length 50 mm for repeatable positioning Workshop version in robust special steel Precision that secures measurement confidence A tolerance of ±0.001 mm positions this gauge pin in the category of high‑precision inspection tools. Such accuracy ensures that small deviations are detected reliably, reducing the risk of out‑of‑tolerance parts progressing through production. For users unfamiliar with metrology terms: a tolerance of ±0.001 mm means that the actual diameter is guaranteed to stay within one thousandth of a millimetre from the nominal 9.31 mm, so repeatability between successive checks is high and statistical variation in quality control datasets is minimised. This level of precision is particularly valuable where final assembly fits or interchangeability are critical. Durable shop‑floor design for reliable workflows Constructed from special steel and specified as a workshop version, the pin balances wear resistance with manageable handling on the production floor. The 50 mm length provides a stable seating in fixtures and gauges, while the modest mass (approx. 0.031 kg) keeps manual handling straightforward during repetitive inspection cycles. The single‑item supply format simplifies inventory control when specific diameters are needed for discrete checking points. The robust material choice supports a long service life under normal inspection use, contributing to lower lifetime costs through reduced replacement frequency. Integrates into inspection processes to save time and rework The pin is designed for fast, low‑complexity measurement operations: insert, check, record. Its nominal 9.31 mm diameter and tight tolerance mean fewer ambiguous readouts and quicker go/no‑go decisions on the line. Using a defined, precision reference element such as this pin shortens the calibration chain for fixtures and minimises setup variation between operators. In practice, that translates to fewer interruptions, less rework and steady throughput—an efficiency argument that aligns with routine quality assurance and first‑article inspection alike. The clear specification supports traceable documentation and straightforward inclusion in quality records. For tailored advice on integrating this Metav IndustryLine gauge pin into existing inspection plans, contact Metav Werkzeuge for ordering and application support at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.931 GTIN: 4061905062599 Brand: Metav IndustryLine Type: Single gauge pin Facts Nominal diameter: 9.31 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.031 kg Special features Workshop version Single item supply Material: special steel Designed for end‑measurement applications FAQ What level of accuracy does the pin provide? The gauge pin offers an accuracy of ±0.001 mm, ensuring high‑precision dimensional checks for critical fits. Is this pin suitable for shop‑floor use? Yes; the workshop design and special steel construction make the pin resilient for routine inspection duties on the production floor. How long is the pin and how does that affect use? With a length of 50 mm, the pin gives stable seating in fixtures and consistent contact for repeatable measurements. Can this pin be used for end‑measurement (end masses) tasks? The design is intended precisely for end‑measurement applications and provides a clearly defined datum for such checks. How is the product supplied and identified? The single gauge pin is supplied individually and is listed under SKU M323.931 with GTIN 4061905062599 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.32mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
The compact workshop test pin delivers ultra-fine repeatability thanks to its ±0.001 mm tolerance and robust special steel construction; combined with a 50 mm length and a precise 9.32 mm diameter, it supports reliable end-dimension checks and fast go/no-go verification. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored measurement advice. M323.932 Precision Gauge Pin — 9.32 mm, ±0.001 mm, 50 mm length M323.932 is a single precision gauge pin for end-dimension verification and tight-tolerance checks in workshop and quality‑assurance environments High-precision ±0.001 mm tolerance Diameter 9.32 mm for exact end measurements 50 mm length for compact assemblies Workshop-grade special steel construction Precision that secures production quality A measurement artefact with a ±0.001 mm tolerance provides a decisive advantage in quality control: deviations are reduced, scrap is prevented and setup times for gauges are shortened. The compact 9.32 mm diameter combined with a 50 mm length makes this pin suitable for tight bores and end‑dimension verification where space is limited. By standardising on a high‑accuracy gauge pin, inspection routines become repeatable and traceable, supporting process capability studies and lowering rework rates. Durable material for frequent shop use Manufactured from special steel, the pin resists wear under repeated seating and withdrawal in gauge blocks or fixtures. The robust construction yields predictable surface contact and retains measurement integrity over many cycles, which reduces the need for frequent replacement and supports a consistent inspection routine. For workshop contexts where handling is frequent, the combination of material choice and precise machining ensures stable contact geometry and sustained precision in everyday use. Practical application and compatibility Designed as a single test pin, this item integrates simply into existing gauge sets and inspection jigs for end‑measurements and acceptance checks. The compact form factor is ideal for dense assemblies, fixture checks and component end‑dimension verification, enabling quick go/no‑go decisions on production lines. Clear, measurable specifications — 9.32 mm diameter, 50 mm length, ±0.001 mm tolerance — make it straightforward to document acceptance criteria within inspection reports and to specify the pin in work instructions. Request the Metav IndustryLine M323.932 precision gauge pin via Metav Werkzeuge for reliable end‑dimension checks — call +49 2822 7131930 or email info@metav-werkzeuge.com for application guidance and local supply from Emmerich. Technical data Article number: M323.932 GTIN: 4061905062605 ECLASS: 21170231 Brand: Metav IndustryLine Facts Diameter: 9.32 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.031 kg Special features Workshop version Material: special steel Single gauge/test pin Suitable for end‑dimension verification FAQ What materials is the M323.932 made from? The M323.932 precision gauge pin is manufactured from special steel designed for workshop use and repeated seating without rapid wear. Is the tolerance of ±0.001 mm suitable for production control? Yes — the ±0.001 mm tolerance of this gauge pin supports tight production tolerances and precise end‑dimension verification in quality control routines. Can this pin be used with standard gauge blocks and fixtures? The single test pin is compatible with common gauge sets and inspection fixtures for end measurements and go/no‑go verification. How does the small diameter and length affect handling? The compact 9.32 mm diameter and 50 mm length facilitate use in confined assemblies and dense fixtures while delivering repeatable contact geometry. Which brand and SKU should be referenced when ordering? Order the Metav IndustryLine precision gauge pin using SKU M323.932 to ensure correct identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.33mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Benefit from a compact instrument that combines workshop robustness with laboratory-grade accuracy: the pin’s ±0.001 mm tolerance and 9.33 mm nominal diameter ensure reproducible end‑measurements and secure go/no‑go fits; order directly via Metav Werkzeuge or consult our advisors for application guidance. Gauge pin M323.933 — 9.33 mm, ±0.001 mm accuracy (Metav IndustryLine) A Gauge pin M323.933 designed for precision end‑measurements, fixture setting and production gauging in workshop and inspection environments Workshop version for robust use Diameter 9.33 mm; high fit accuracy Tolerance ±0.001 mm for end measurements Length 50 mm, special steel construction Precision where repeatability reduces rework A compact verification pin delivers consistent reference dimensions when tolerance margins are tight. The ±0.001 mm accuracy specifies the maximum deviation from nominal size, which makes this pin suitable for final acceptance checks and plug‑gauge tasks where reproducibility is essential. Manufactured from special steel, the item maintains dimensional stability under frequent handling and provides a reliable datum for comparative checks. The numerical tolerance is expressed in micrometres to clarify expectations in quality documentation and control charts. Designed for reliable workshop operation The solid single‑piece construction and a 50 mm overall length make the pin easy to seat in fixtures, gauges and component bores without sacrificing stiffness. The 9.33 mm nominal diameter maps directly to common hole classes used in small part production, supporting quick go/no‑go assessments and setting of clamping devices. The workshop execution emphasises durability and uncomplicated handling so that routine checks remain fast and repeatable, contributing to reduced inspection times and fewer downstream adjustments. Traceable identification and practical use in quality routines Marked for commercial identification, the pin integrates into traceability processes and inventory systems to help maintain consistent inspection protocols. Its compact mass and single‑unit supply suit pick‑and‑place workflows and metrology benches alike, supporting both in‑process control and final inspection steps. Using a standardised verification pin simplifies documentation for audits and provides a stable reference when validating measuring stations or calibrating comparative fixtures. Choose the Metav IndustryLine M323.933 when sub‑micron repeatability matters — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss suitability and delivery Technical data SKU: M323.933 GTIN: 4061905063015 eClass: 21170231 Article type: Gauge pin Brand: Metav IndustryLine Core specifications Diameter: 9.33 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.031 kg Materials & features Material: Special steel Single piece design Workshop execution FAQ What is the nominal diameter and tolerance of this gauge pin? The nominal diameter is 9.33 mm with a tolerance of ±0.001 mm for the Metav IndustryLine gauge pin M323.933. Which applications are suitable for this verification pin? Typical uses include end‑measurements, plug‑gauging, fixture setting and quick go/no‑go checks in production and inspection workflows. What material is the pin made from and what does that mean for wear? The pin is made from special steel, offering durable dimensional stability under routine handling and frequent insertion into fixtures. Is the product supplied as a single item or as a set? The item is supplied as a single gauge pin, designated by SKU M323.933 for individual ordering and inventory control. How can this pin support quality documentation and traceability? Identification via GTIN and eClass allows integration into inspection records and inventory systems, aiding repeatable procedures and audit trails. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.34mm Precision Gauge Pin ±0.001mm, 50mm Length, Workshop Finish - Metav IndustryLine
Precise end‑measurement and alignment are delivered by the combination of ±0.001 mm tolerance and a robust special steel construction; the 9.34 mm diameter and 50 mm length provide a stable reference for gauging and fixture set‑up. Order this gauge directly from Metav Werkzeuge or request application advice from their specialists. Gauge pin, single, 9.34 mm (M323.934) — 50 mm length, ±0.001 mm, Metav IndustryLine The Gauge pin M323.934 is a single precision reference pin intended for end‑measurement, alignment and fixture verification in workshop environments ±0.001 mm high repeatability 9.34 mm pre‑ground diameter 50 mm hardened length for stability Workshop execution with transport case Accuracy that keeps production within tolerance A ±0.001 mm specification ensures the pin functions as a reliable reference for fine measurement and repeat checks. In practical terms, this level of accuracy reduces measurement uncertainty in assembly and inspection tasks where micrometric deviation matters. The ground 9.34 mm diameter provides a defined reference surface for plug‑type checks, while the 50 mm length maintains concentricity and minimises end‑play. Such dimensional stability supports consistent quality control and shorter rework cycles, contributing directly to process efficiency. Robust construction for everyday workshop use Built in a workshop execution and manufactured from special steel, the pin balances wear resistance with handling convenience. The material choice and pre‑ground finish mean the reference surface resists light knocks and repeated insertion cycles, extending service life compared with untreated pins. At 0.031 kg the component is easy to position yet substantial enough to avoid unwanted vibration during measurement. Delivered in a transport case, the pin remains protected during storage and transit, preserving the factory ground dimensions until use. Practical applications in gauges and fixture set‑ups The pin serves as an end‑measure reference for alignment, fixture verification, and repeat positional checks on assemblies. Its geometry makes it suitable for use as a reference leg in gauge nests, for checking bore runout with complementary measuring equipment, or as a precision dowel for setting up jigs. The simple form factor allows integration into existing inspection routines with minimal training; technicians can rely on the pin as a repeatable datum when establishing concentricity or axial positions. Traceability, identification and handling considerations Marked by its SKU and GTIN, the component is straightforward to catalogue within inventory and quality records. Lightweight handling and a compact transport solution make the pin suited to bench‑level use or mobile inspection kits. Routine care—cleaning with a lint‑free cloth and light oiling of the surface—preserves the ground finish and maintains measurement integrity over time. For tailored solutions, the pin can be combined with other gauge pins and fixture elements to create multi‑point inspection tools. For precise end‑measurement tasks, specify the Metav IndustryLine M323.934 gauge pin and contact Metav Werkzeuge in Emmerich for ordering and application guidance Technical data Article number: M323.934 GTIN: 4061905063022 Name: Gauge pin, single, 9.34 mm; ±0.001 mm; 50 mm Brand: Metav IndustryLine Version: Workshop execution Delivery: Transport case Core specifications Diameter: 9.34 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.031 kg Features and applications Material: Special steel Use: End‑measurement, alignment, fixture reference Finish: Pre‑ground diameter Packaging: Case for transport FAQ What level of precision does this pin provide? The M323.934 gauge pin offers a repeatability of ±0.001 mm, making it suitable for micrometric reference tasks and tight tolerance checks in manufacturing and inspection. What are the exact dimensions of the pin? This item is a 9.34 mm diameter pin with a length of 50 mm, specified and supplied as the Metav IndustryLine gauge pin M323.934. Is the pin suitable for use in fixture set‑ups and gauge nests? Yes, the M323.934 is designed for fixture verification and can serve as a stable reference dowel in gauge nests and jigs where precise end‑measurement is required. How should the pin be maintained to preserve accuracy? Routine care for the M323.934 includes wiping with a lint‑free cloth, applying light protective oil to avoid corrosion, and storing the pin in the supplied transport case when not in use. How is the item supplied and identified for inventory? The gauge pin M323.934 is delivered in a transport case and is identifiable by its SKU (M323.934) and GTIN (4061905063022), facilitating traceability and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.35mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the ±0.001 mm tolerance, compact 9.35 mm diameter and robust 50 mm length to secure reproducible end‑size checks in production; delivered in a protective transport box via Metav Werkzeuge for immediate workshop use or expert consultation. M323.935 Gauge pin (single) – 9.35 mm, ±0.001 mm, 50 mm length | Metav IndustryLine The M323.935 gauge pin is a workshop‑grade precision pin for end‑size verification and fit testing in production and inspection environments. Workshop‑grade construction Diameter 9.35 mm, tolerance ±0.001 mm 50 mm length for end‑size verification Supplied in protective transport box High precision that reduces rework and inspection time The narrow ±0.001 mm tolerance delivers measurable gains in process reliability when used for final size checks and clearance tests; this level of control prevents escape of out‑of‑tolerance parts and lowers rework rates. The supplied pin is manufactured from special steel, which ensures stable dimensions under repeated handling and contact. By choosing a calibrated measuring reference with defined tolerance, inspection routines become faster and decisions on acceptance or corrective action more objective—ideal for controlled production workflows. Robust design for daily workshop use Built as a workshop‑grade component, the pin resists typical handling stresses and maintains its form thanks to the special steel composition. The compact 50 mm length and low mass make it easy to position in fixtures or measuring jigs, while the protective transport box preserves surface quality between uses and during transfer across workstations. The construction supports repeated insertion and withdrawal without notable wear, so dimensional stability is retained over many measurement cycles. Practical compatibility with inspection processes This single gauge pin serves as a reliable reference for end‑size verification and assembly checks where a defined shaft diameter is required. The clear numeric specification—9.35 mm diameter with ±0.001 mm deviation—facilitates integration into existing quality plans and measurement reports. Traceability is supported by the visible SKU and GTIN, enabling seamless stock control and documentation in quality management systems. For workshop environments seeking compact, high‑precision references, this pin is an efficient, space‑saving option. Contact Metav Werkzeuge for tailored advice on using the Metav IndustryLine M323.935 gauge pin in inspection routines and to confirm availability for immediate supply. Technical data Article number: M323.935 GTIN: 4061905063039 Brand: Metav IndustryLine Facts Diameter: 9.35 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.031 kg Special features Workshop‑grade construction Material: special steel Protective transport box included Application: end‑size verification and fit testing FAQ What tolerance does this gauge pin offer? The gauge pin is specified with a tolerance of ±0.001 mm, making the M323.935 suitable for high‑precision end‑size checks. Which material is used for the pin? The pin is manufactured from special steel, offering dimensional stability and wear resistance for workshop use. Is the pin suitable for routine assembly checks? Yes, the design and precise diameter of the gauge pin make it well suited for assembly clearance tests and fit verification. How is the pin supplied for transport and storage? The pin is supplied in a protective transport box to maintain surface quality during handling and transfer. Can the M323.935 be used in fixture‑based inspections? Yes, the compact length and stable diameter allow straightforward use in inspection fixtures and measuring jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.36mm Gauge Pin, Workshop Version, ±0.001 mm, Length 50 mm - Metav IndustryLine
Take advantage of a workshop-grade gauge pin that pairs ultra-fine ±0.001 mm tolerance with a robust special steel shaft for dependable end‑size checks; the 9.36 mm diameter and 50 mm length deliver repeatable reference points for setting, inspection and fixture alignment. Order the test pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.936 Gauge Pin — 9.36 mm, ±0.001 mm, Metav IndustryLine A M323.936 single test pin designed for precise end‑size verification and routine reference measurements in metrology and quality control. Workshop version construction Tolerance ±0.001 mm Diameter 9.36 mm length 50 mm Consistent reference for end‑size verification The primary strength of this test pin is its accuracy: with a specified tolerance of ±0.001 mm, the component serves as a high‑precision reference for bore checks, reamer verification and calibration tasks. The controlled diameter of 9.36 mm provides a stable datum that reduces measurement scatter and speeds inspection cycles. Using a fixed‑dimension pin instead of variable gauges simplifies pass/fail decisions and supports traceable quality records, improving throughput in routine metrology operations. Robust build for everyday workshop use Manufactured in special steel and finished for workshop conditions, the pin resists wear under frequent handling and maintains form at the contact edge. The 50 mm shaft length offers a practical balance between accessibility and stiffness, enabling stable seating in fixtures and easy engagement with internal bores. This durability translates into fewer replacements and less downtime, which supports a reliable production flow and lowers total cost of ownership for inspection tooling. Designed to integrate into quality workflows The single test pin is an efficient tool for precise setting, gauging and alignment tasks within machining and assembly processes. Its compact form factor supports rapid checks on the shop floor and straightforward storage in inspection kits. Paired with clear labelling and traceable identifiers, the pin helps maintain measurement consistency across shifts and operators, reinforcing production confidence and traceability in quality documentation. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply of the M323.936 gauge pin. Technical data Article number: M323.936 GTIN: 4061905063855 Manufacturer: Metav IndustryLine Facts Diameter: 9.36 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.031 kg eClass: 21170231 Special features Workshop version Material: special steel Single test pin Label: Prüfstift, einzeln, 9,36mm, +/- 0.001 mm Länge 50 mm FAQ What is the intended use of this gauge pin? The M323.936 gauge pin is intended for end‑size verification, bore checks and fixture alignment as a precision reference in metrology and workshop inspections. How precise is the diameter of the test pin? The test pin is manufactured to a tolerance of ±0.001 mm, providing the fine accuracy required for repeatable reference measurements and tight control checks. Which material is used for the pin and why does it matter? The shaft is made from special steel, chosen for dimensional stability and wear resistance so the pin maintains roundness and length under frequent use. Can the pin be used for setting reamers or spindles? Yes, the M323.936 single test pin is suitable as a reference for setting and checking reamers, spindles and alignment fixtures where a fixed, precise diameter is required. Is traceability information available for this part? The product carries a clear article number and GTIN for traceability; please request additional documentation from Metav Werkzeuge if certificate details are needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.37mm Gauge Pin, Workshop Finish, ±0.001mm, Length 50mm - Metav IndustryLine
Take advantage of the combination of sub-micron accuracy, a compact 50 mm working length and robust special steel construction for repeatable end‑measurements in the workshop; order the gauge pin directly via Metav Werkzeuge or ask our consultants for specification advice. M323.937 — Precision Gauge Pin, Ø 9.37 mm, ±0.001 mm (Metav IndustryLine) The M323.937 is a single precision gauge pin designed for accurate end‑measurements and fit verification in workshop inspection and quality control tasks. Diameter 9.37 mm with ±0.001 mm tolerance 50 mm hardened special steel length Workshop version with protective box Consistent measurement accuracy for tight tolerances The gauge pin delivers ±0.001 mm positional consistency owing to its finely finished diameter of 9.37 mm, which is suitable where small clearances or interference fits must be verified. The tight tolerance reduces measurement uncertainty and supports reliable go/no‑go assessments during incoming inspection or final assembly. The described tolerance class corresponds to high‑precision workshop gauges and allows short, repeatable checks without the overhead of complex fixtures. Robust design for everyday workshop handling Manufactured from special steel, the pin is produced to withstand routine use in a production environment while maintaining its dimensional stability. The 50 mm length balances handling convenience with sufficient engagement for most end‑measurement tasks; the workshop version indicates a rugged finish and practical handling features that simplify placing and removing the pin during quick checks. A finished surface reduces the risk of fretting and eases cleaning between uses. Ready for inspection and storage The pin is supplied as a single unit in a protective box suitable for transport and short‑term storage, which helps preserve the calibrated condition between uses. The compact format supports organised inspection benches and simplifies traceability when combined with workshop documentation. For traceable quality processes, the compact delivery format makes the pin easy to store with inspection records or to dispatch within production lines. Contact Metav Werkzeuge for availability and technical clarification on the M323.937 precision gauge pin, supplied from our Emmerich site and ready for immediate inclusion in quality workflows. Technical Data Article number: M323.937 GTIN: 4061905063862 SKU: M323.937 Weight: 0.031 kg Facts Diameter: 9.37 mm Tolerance: ±0.001 mm Length: 50 mm Special features Material: Special steel Workshop version Delivered in protective box ECLASS: 21170231 FAQ What is the intended use of this gauge pin? The M323.937 precision gauge pin is intended for end‑measurements, fit checks and quick inspection tasks in workshop and quality‑control environments. Is the diameter tolerance suitable for precision assembly checks? Yes; the ±0.001 mm tolerance of this gauge pin makes it suitable for assembly verification where sub‑millimetre clearance control is required. Which material is used and how does it affect durability? The pin is manufactured from special steel, offering a balance of hardness and corrosion resistance appropriate for routine workshop use. How is the product delivered for safe handling? The pin is supplied as a single unit in a protective box to safeguard the finished diameter during transport and storage. Can the pin be used for comparative gauging against pins and rings? The M323.937 precision gauge pin is suitable for comparative gauging and short functional checks where its diameter and tolerance match the inspection requirement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.38mm Test Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of sub‑micron repeatability, compact dimensions and robust workshop grade material to ensure reliable go/no‑go checks. Order the pin directly via Metav Werkzeuge or consult the team for application advice. M323.938 gauge pin — 9.38 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A M323.938 gauge pin designed for precise end‑measure verification and tight‑tolerance inspection tasks in workshop and production environments. 9.38 mm diameter, ±0.001 mm tolerance 50 mm length for compact inspection set‑ups Workshop‑grade special steel construction Single‑piece supply for individual checks Precision where repeatability matters The core advantage of this inspection pin is its accuracy of ±0.001 mm, which places it in the high‑precision category for gauge pins. That level of precision reduces uncertainty in end‑measure checks and repetitive gauging tasks, supporting consistent pass/fail decisions on production lines. As a hardened, dimensionally stable measuring element, the pin minimises wear‑related drift and keeps quality control procedures efficient and predictable. Compact dimensions for versatile applications With a diameter of 9.38 mm and a length of 50 mm, the pin fits into compact fixtures and assembly jigs while still providing a reliable reference surface. The modest size simplifies handling during manual inspection and allows straightforward integration into bench‑top test rigs. The compact format is particularly suitable for end‑measure control of small components, alignment checks and precision plug‑testing where space and accessibility are limited. Robust material for workshop conditions Manufactured from special steel in a workshop execution, the pin balances surface hardness with resistance to routine handling. The chosen material ensures that the reference surface resists minor nicks and maintains dimensional stability under normal inspection stresses. For practical workshop use, the construction supports repeated insertion and withdrawal without rapid degradation of the contact surface, extending service life and lowering total cost of ownership. Practical benefits for quality workflows Incorporating this gauge pin into a quality procedure simplifies routine checks: the high dimensional fidelity translates into fewer retests and more decisive measurement outcomes. The single‑piece supply is convenient for shops that maintain individual reference pins for specific fixtures or measurement stations. Where documented tolerances are required for traceable inspections, the stated ±0.001 mm tolerance provides a clear performance benchmark for documentation and quality records. Choose Metav IndustryLine’s M323.938 gauge pin for dependable high‑precision end‑measure checks — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for product availability and sourcing. Technical data Article number: M323.938 GTIN: 4061905063879 Material: Special steel Version: Workshop execution Supply: Single piece Facts Diameter: 9.38 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.031 kg Special features High‑precision tolerance specification Compact form for fixtures and jigs Suitable for end‑measure verification SKU: M323.938 FAQ What diameter and tolerance does the gauge pin have? The M323.938 gauge pin measures 9.38 mm in diameter and is specified to an accuracy of ±0.001 mm for high‑precision checks. Which material is the pin made from? The inspection pin is made from special steel and supplied in a workshop execution suitable for routine use. Is this pin suitable for fixture and jig applications? Yes — the 50 mm length and compact diameter make the pin well suited to fixture use, alignment checks and end‑measure verification in small assembly stations. How is the pin supplied? This item is supplied as a single‑piece gauge pin, intended for individual reference or dedicated fixture use. Can the M323.938 replace existing reference pins in a quality routine? The ±0.001 mm tolerance and robust material make this pin a practical replacement where improved repeatability and tighter pass/fail decisions are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.39mm Gauge Pin Hardened Steel 50mm Length ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial‑grade ±0.001 mm accuracy, a compact 50 mm length and durable special steel for reproducible end‑dimension checks; procure the part directly via Metav Werkzeuge or consult our specialists for application advice. M323.939 — Gauge pin, Ø 9.39 mm, ±0.001 mm (Workshop version) — Metav IndustryLine The M323.939 is a single precision gauge pin with a nominal diameter of 9.39 mm and a length of 50 mm, designed for reliable end‑measure verifications in workshop metrology and fixture set‑up. Workshop version, robust design Diameter 9.39 mm, tolerance ±0.001 mm Length 50 mm for end‑measure checks Special steel for long service life Precision that reduces inspection uncertainty High‑accuracy checking relies on stable reference dimensions. With a diameter tolerance of ±0.001 mm and a nominal size of 9.39 mm, this gauge pin provides a defined reference for end‑dimension control and fit verification. The exceptional tolerance translates directly into fewer re‑measurements and more consistent accept/reject decisions during incoming inspection or in‑process checks. Engineers and quality technicians benefit from sharper control limits and faster throughput because measurement scatter caused by the reference tool is minimised. Built for workshop handling and longevity The pin’s special steel composition and workshop execution ensure geometric stability under frequent use. At a length of 50 mm the pin is long enough for practical end‑measure tasks yet short enough to remain rigid and easy to handle on assembly benches. A single‑piece construction preserves concentricity and surface integrity, which reduces wear‑induced measurement drift. The combination of material selection and robust design offers a low maintenance profile, supporting regular production work without premature rework or replacement. Practical integration into inspection and fixture workflows This single gauge pin is suitable for quick gauge checks, go/no‑go comparisons in fixtures and verification of bore end dimensions. Its compact form factor makes it compatible with bench gauges, comparator stands and manual jigging operations where a precise, repeatable datum is required. Handling is straightforward and measurement steps can be standardised in inspection plans to improve traceability. The clear numeric specification simplifies documentation in quality records and supports process audits without ambiguity. For consistent workshop metrology, request the Metav IndustryLine M323.939 via Metav Werkzeuge — specialists in precision tools based in Emmerich who can advise on application and procurement Technical data SKU: M323.939 GTIN: 4061905063886 Category: Messstifte Material: Special steel Diameter (nominal): 9.39 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.031 kg Core specifications Diameter: 9.39 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.031 kg Special features Workshop execution Single gauge pin Intended use: end‑dimension checks and fit verification ECLASS: 21170231 FAQ What tolerance and nominal size does this gauge pin provide? The M323.939 gauge pin is specified at 9.39 mm nominal diameter with a tolerance of ±0.001 mm, ideal for tight end‑dimension control. What material is used for the pin and how does it affect longevity? The pin is made of special steel, chosen for wear resistance and dimensional stability, which supports extended service life in routine workshop use. Is the M323.939 a single item or part of a set? This entry is a single precision gauge pin supplied individually for targeted inspection or fixture applications. Which typical tasks is this gauge pin suited to? Typical applications include end‑measure verification, fixture set‑up, go/no‑go checks for bores and assembly alignment where a stable reference diameter is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.3mm Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
The combination of ±0.001 mm repeatability, a 9.30 mm nominal diameter and a compact 50 mm length makes this gauge pin ideal for reliable end‑measure checks in production. Order the part directly via Metav Werkzeuge or contact our consultants for application advice. M323.930 Gauge Pin — 9.30 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) M323.930 is a single, workshop‑grade gauge pin for reference and end‑measure verification in inspection and production environments ±0.001 mm tolerance for high precision 9.30 mm nominal diameter in special steel 50 mm overall length for compact checks Workshop‑grade finish for durable handling Fast, measurable confidence for diameter checks This reference pin delivers repeatable results because the geometric tolerance of ±0.001 mm minimises measurement uncertainty when used as an end‑measure or reference contact. The small overall length reduces lever effects and ensures stable readings during quick go/no‑go checks or when used with dial or digital comparators. Such a tight tolerance translates directly into fewer rejects and clearer pass/fail decisions on the shop floor. Durable construction for everyday workshop use Machined from special steel, the pin is designed for repeated contact with bore and plug surfaces while maintaining form stability. The workshop‑grade finish resists light wear and allows straightforward cleaning after use; this reduces the need for frequent replacement and supports longer service intervals. The compact mass also helps to limit operator‑induced deflection during manual inspection. Integrates into inspection routines and fixtures With a nominal diameter of 9.30 mm and an overall length of 50 mm, the component functions well as a handheld reference or as a fixed reference element in custom fixtures. The low mass and compact dimensions permit easy alignment in tight assemblies and make measurement setups quicker to assemble. When traceability and reproducibility are required, this pin provides a simple, robust reference for end‑measure verification. For reliable end‑measure verification, request the M323.930 from Metav IndustryLine via Metav Werkzeuge — expert application support is available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.930 GTIN: 4061905062582 Brand: Metav IndustryLine Category: Messstifte Special feature: Werkstatt‑Ausführung Facts Nominal diameter: 9.30 mm Tolerance: ±0.001 mm Overall length: 50 mm Weight: 0.031 kg Special features Material: special steel Supply: single piece Intended use: reference/end‑measure checks FAQ What applications suit this gauge pin best? The gauge pin is intended for end‑measure verification and reference checks in workshop and production inspection tasks; the M323.930 performs well for bore gauging and short‑range dimensional references. How precise is the M323.930 in daily use? With a specified tolerance of ±0.001 mm, the M323.930 offers high precision suitable for fine inspection work where tight dimensional control is required. Can the pin be used in fixtures and jigs? Yes — the compact 50 mm length and stable geometry allow the pin to be mounted or used as a reference element within custom fixtures and inspection jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.41mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy, robust material choice and compact workshop design for reliable end‑measure checks — order the part directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine M323.941 gauge pin — 9.41 mm, ±0.001 mm, 50 mm The Metav IndustryLine M323.941 gauge pin is a single, high‑precision test pin for end‑measure and inspection applications in machine shops and quality departments. Precision diameter 9.41 mm ±0.001 mm 50 mm length in workshop execution Manufactured from special steel Suitable for end‑gauge and inspection tasks High precision for repeatable end‑measure checks The M323.941 gauge pin delivers micrometre‑level control with a nominal diameter of 9.41 mm and a tolerance of ±0.001 mm. This equivalence to one micron makes the component suitable where repeatability matters: plug and verify operations, reference checks in fixtures, or comparative testing during setup. The tight tolerance is presented as a measurable, verifiable attribute, supporting faster decision‑making on conformity without guesswork. The hardened, dimensionally stable shaft minimises wear and keeps inspection intervals predictable. Robust construction that supports everyday workshop use Manufactured from special steel, the test pin combines surface resistance with the rigidity required for frequent contact measurements. The 50 mm length provides enough engagement for secure seating in gauges and jigs while remaining compact for handling and storage. The workshop execution is designed to withstand regular use on benches and in fixture assemblies; the material choice reduces the need for early replacement and helps maintain stable measurement references over time. In practice, this means fewer interruptions to production and a steadier quality workflow. Practical integration and measurable benefits As a single‑piece gauge pin, the item is ideal for precision verification, end‑measure control and use as a reference element in assembly or inspection rigs. The small form factor and certified dimensional data simplify integration into existing processes: identification is straightforward, and exchange with existing gauges or test fixtures is direct thanks to the standardised diameter and length. Relying on a precise reference pin like this shortens setup time, reduces rework and supports documented quality procedures in machining and inspection environments. Contact Metav Werkzeuge for procurement and technical advice on the Metav IndustryLine M323.941 gauge pin to ensure precision in end‑measure inspection Technical Data Article number: M323.941 GTIN: 4061905063909 Manufacturer: Metav IndustryLine Weight: 0.031 kg Material: Special steel Facts Diameter: 9.41 mm Tolerance: ±0.001 mm Length: 50 mm Accuracy (specified): ±0.001 mm Special features Workshop execution Single test pin delivery ECLASS: 21170231 Application focus: end‑measure and inspection FAQ What is the nominal diameter and its tolerance? The nominal diameter is 9.41 mm with a tolerance of ±0.001 mm, specified for the Metav IndustryLine M323.941 gauge pin. Can this pin be used as a reference in fixture assembly? Yes. The pin’s 9.41 mm diameter and 50 mm length make it suitable as a reference element in fixtures and gauge assemblies for end‑measure checks. What material is the test pin made from? The Metav IndustryLine M323.941 is made from special steel, selected for dimensional stability and workshop durability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.42mm Gauge Pin Single ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, sub-micron tolerance and compact handling for reliable end-measurement tasks; robust special-steel construction and delivery in a transport case support daily shop-floor use. Order the (gauging pin, single 9.42 mm, ±0.001 mm, length 50 mm) directly via (Metav Werkzeuge) or ask our consultants if needed. Gauging pin M323.942 — single precision pin, 9.42 mm diameter, ±0.001 mm (Metav IndustryLine) The gauging pin M323.942 is a workshop-grade precision pin designed for end-measurements and tolerance verification in production and quality control environments, offering tight dimensional control in confined measuring tasks. Workshop-grade execution for everyday use Diameter 9.42 mm with ±0.001 mm tolerance 50 mm length in robust special steel Delivered in a transport case for protection Accuracy and repeatability for production control This measuring pin provides a tolerance of ±0.001 mm, which corresponds to a 1-micron accuracy ideal for high-precision end-measurement tasks where repeatability is crucial. The tight tolerance makes the pin suitable for final size checks, go/no-go verification when paired with gauge blocks or dedicated fixtures, and as a reference element in dimensional control routines. The compact diameter of 9.42 mm and 50 mm overall length make this tool easy to handle on assembly lines and in inspection benches, while the workshop-oriented finish ensures resistance to routine handling without compromising measurement integrity. Designed for the shop: material and protection Manufactured from special steel, the pin balances surface hardness with corrosion resistance to preserve the measuring diameter under frequent use. The workshop-grade execution reflects machining and heat-treatment processes selected to keep the geometry stable during repetitive contact with parts and fixtures. Delivery in a transport case provides immediate protection against knocks and contamination during storage or transit, reducing the risk of damage that would affect accuracy. These practical aspects reduce downtime for replacements and support consistent measurement results across shifts. Practical integration into inspection workflows The pin is ready to be integrated into established inspection procedures: its compact form factor fits with gauge blocks, fixture plates, and portable comparators, supporting both in-line checks and laboratory verification tasks. Labelling and traceability are supported by the supplied SKU and GTIN for inventory control and quality records, facilitating lot tracking and procurement. The high-precision end-measurement pin is particularly useful where small tolerances are decisive—toolroom sampling, final inspection of turned components and fit checks in assembly—ensuring measurable process confidence without complex equipment changeover. Contact Metav Werkzeuge for application advice or to request an order for the Metav IndustryLine gauging pin M323.942; reach the team at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.942 GTIN: 4061905063916 Label: Gauging pin, single, 9.42 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.42 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.031 kg Special features Workshop-grade execution Material: special steel Delivered in transport case High-precision end-measurement pin FAQ What tolerance does the pin offer? The pin provides a tolerance of ±0.001 mm; the M323.942 gauging pin is therefore suitable for checks that require micron-level precision. Is the pin suitable for production checking of turned parts? Yes; the M323.942 is designed for repetitive end-measurements and fit checks in production, where its compact form and tight tolerance aid fast verification. What material is used for the pin? The pin is made from special steel, chosen to maintain geometric stability and resist wear during routine workshop use. Does the delivery include protection for transport? Delivery of this item includes a transport case, providing protection against knocks and contamination during storage and transit for the M323.942. How is the product identified for inventory and ordering? The item is listed under article number M323.942 and GTIN 4061905063916 for procurement and traceability purposes. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.43mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from micron-level control with ±0.001 mm accuracy and a precise 9.43 mm diameter, combined with a 50 mm length in durable special steel for reliable inspection and end‑measure tasks. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 9.43 mm diameter, 50 mm length (Metav IndustryLine) A single gauge pin designed for precision end‑measure and inspection tasks in metrology applications, ideal where tight tolerances and repeatable fits are required. 1 µm accuracy for tight tolerances Hardened special steel for durability Compact 50 mm length for confined spaces Workshop version for everyday industrial use Consistent micron accuracy for inspection and assembly The pin delivers ±0.001 mm tolerance, which translates to 1 µm repeatability that supports high‑precision checks and go/no‑go assessments. Such resolution is typically associated with specialised metrology tools and enables confident decision‑making during final inspection or assembly verification. The fine tolerance reduces measurement uncertainty and helps maintain process capability when used as a reference gauge in quality control routines. Robust construction that keeps calibration longer Manufactured from special steel, the component resists wear under repeated seating and withdrawal, preserving geometry over extensive cycles. The 50 mm length is a practical compromise between handling and reach, allowing access into moderately recessed bores while remaining easy to position by hand or in fixtures. The workshop version designation signals a design balanced for everyday industrial environments where both toughness and dimensional fidelity are required. Practical integration into metrology workflows Supplied as a single precision pin, the item is suitable for use as a reference in plug fits, end‑measure checks and functional clearance tests. The compact format and standard diameter of 9.43 mm make it compatible with common inspection benches and fixture arrangements. Traceable performance at the micron level supports process documentation and can be incorporated into statistical process control routines to aid defect reduction and reproducibility. Contact Metav Werkzeuge today for tailored application guidance or to arrange a purchase through our Emmerich distribution centre where specialist advice and dependable supply are provided Technical Data Article number: M323.943 GTIN: 4061905064449 Brand: Metav IndustryLine Material: Special steel Facts Diameter: 9.43 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.031 kg Special features Single gauge pin Workshop version Intended for precision end‑measure tasks FAQ What level of precision does this gauge pin provide? The gauge pin delivers ±0.001 mm accuracy, enabling 1 µm repeatability for precise end‑measure and inspection operations. Is the material suitable for repeated use in a production environment? Yes, the pin is made from special steel and the workshop version is designed for robust daily use while maintaining dimensional stability. Can this pin be used in fixture-based inspection setups? The 9.43 mm diameter and 50 mm length make the pin compatible with common fixture arrangements; the component is suitable as a reference element in bench or fixture inspections. Does the product come as a single item or in sets? This listing is for a single gauge pin; the SKU M323.943 identifies the individual item supplied by Metav IndustryLine. What applications are typical for this gauge pin? Typical uses include plug fits, end‑measure verification, final inspection and functional clearance testing where micron‑level control is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.44mm Test Probe, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combining workshop-grade special steel, a compact 50 mm test length and a ±0.001 mm tolerance, this measuring pin delivers reproducible end‑dimension checks and durable shop‑floor performance. Order the M323.944 directly via Metav Werkzeuge or consult our advisors for application support. M323.944 — Single measuring pin, Ø 9.44 mm, ±0.001 mm, 50 mm length by Metav IndustryLine M323.944 is a single‑piece inspection pin designed for high‑precision end‑dimension checks in workshop environments and quality control stations. ±0.001 mm repeatable tolerance Nominal diameter 9.44 mm 50 mm inspection length Workshop‑grade special steel Accuracy that reduces rework and inspection time The compact inspection pin is engineered for high repeatability, with a declared tolerance of ±0.001 mm that supports tight acceptance criteria and reduces the need for rework. Used as a reference for go/no‑go checks or in comparison gauges, the precision of this measuring element minimises measurement uncertainty and accelerates pass/fail decisions. The small mass and stable geometry ensure consistent contact conditions during repetitive checks, improving throughput in batch inspection routines. Built to withstand the workshop Manufactured from special steel and specified as a workshop version, the measuring pin tolerates everyday handling and retains dimensional stability during routine use. The 50 mm usable length and nominal 9.44 mm diameter provide a compact form factor that fits into confined fixtures and transfer jigs, while the choice of material balances wear resistance with ease of maintenance. Delivery in a transport case protects the gauge during storage and transit, keeping reference surfaces free from contamination. Integration into measurement workflows As a single inspection element, the pin adapts easily to manual gauging setups, fixture assemblies and optical comparison benches. Its defined geometry supports straightforward insertion into bore gauges or mating sockets for quick verification of end dimensions. Where traceability is required, the clear nominal value and tight tolerance simplify documentation and statistical process control routines, helping to maintain consistent production quality across shifts and operators. Practical benefits for quality teams The compact design reduces handling time, enabling faster cycle checks without sacrificing control. The robust construction lowers the frequency of replacement parts, which in turn supports predictable maintenance planning. For workshops seeking dependable metrology tools, this inspection pin offers a balance of precision, durability and practical size that suits both bench checks and fixture‑based inspections. Contact Metav Werkzeuge in Emmerich for ordering assistance or bespoke advice on integrating the M323.944 into existing inspection fixtures — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.944 GTIN: 4061905064456 Weight: 0.031 kg Facts Diameter: 9.44 mm Length: 50 mm Tolerance: ±0.001 mm Mass: 0.031 kg Special features Workshop version Material: special steel Delivered in transport case Single inspection pin Category: measuring pins FAQ What is the intended use for this inspection pin? The M323.944 measuring pin is intended for precise end‑dimension checks, fixture verification and pass/fail inspections in workshop and production quality environments. Which materials is the pin compatible with during inspection routines? The measuring pin is a reference artefact and is suitable for verifying dimensions of parts made from metals and plastics when used in typical gauging set‑ups; the pin itself is manufactured from special steel for wear resistance. How should the measuring pin be stored to preserve accuracy? Store the inspection pin in its transport case when not in use; the case supplied with the M323.944 protects the reference surfaces from contamination and mechanical damage. Can the pin be used in automated fixtures or only manual checks? The compact geometry and single‑piece design of this inspection pin make it suitable for both manual checks and integration into automated or semi‑automated fixturing systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.45mm Gauge Pin Single, ±0.001mm Tolerance, Length 50mm, Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-grade gauge pin that combines sub-micron repeatability and a robust special steel body for reliable end‑dimension checks — ideal for routine inspection and tooling set‑up. Order directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single 9.45 mm ±0.001 mm, length 50 mm (Metav IndustryLine) The gauge pin, single 9.45 mm ±0.001 mm, 50 mm is a workshop‑grade reference pin designed for precise bore verification and end‑dimension measurements in production and inspection environments Workshop version construction Diameter 9.45 mm, tolerance ±0.001 mm 50 mm overall length for deep gauges Supplied in transport case Consistent sub‑micron performance for inspection work Engineered for repeatable verification, this compact reference pin delivers an accuracy of ±0.001 mm, making it suitable where tight tolerances are required. The small diameter of 9.45 mm and the minimal form deviation support consistent contact with measurement surfaces, reducing uncertainty in comparative gauging routines. Presented as a single gauge element, it serves as a precise datum for checking bores, pin fits and final dimensions in assembly processes, providing a clear, measurable improvement in process control. Built for the workshop — durable materials and practical handling Constructed from special steel, the pin is optimised for everyday use in workshop conditions: wear resistance and dimensional stability extend service life under repeated insertion and extraction. The 50 mm overall length allows access into deeper bores while maintaining sufficient rigidity for straightness during measurement. Delivered in a transport case to protect accuracy during storage and transit, the format suits bench‑level metrology stations and portable inspection kits where robustness and traceability are valued. Seamless integration into inspection routines and fixtures As a reference gauge, this pin complements existing inspection equipment and fixturing: it can be combined with dial gauges, CMM setups or manual checking stations to establish end‑measure references or validate tooling. The compact form is convenient for quick interchange in comparative checks and for use as an end stop in custom fixtures. With its workshop orientation, the component supports efficient process checks that reduce rework and improve assembly consistency. For ordering or application support, contact Metav Werkzeuge directly — Metav’s specialists in Emmerich provide product advice and fast delivery: +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.945 GTIN: 4061905064968 Brand: Metav IndustryLine Facts Diameter: 9.45 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.031 kg Special features Material: special steel Workshop version construction Supplied in transport case for transport protection Category: gauge pins Application hint: end‑dimension checks / bore verification FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.945 is specified with a tolerance of ±0.001 mm, providing high‑precision reference performance for tight tolerance inspections. Which material is used for the pin? The pin is made from a special steel designed for workshop durability and dimensional stability under regular use. Is the pin supplied with a protective case? Yes, delivery includes a transport case to protect the pin during handling and transit. What typical applications suit this reference pin? Typical uses include bore verification, plug‑gauge comparisons, end‑dimension checks and use as a reference in fixturing and manual inspection routines. Does the product data indicate calibration on delivery? The available product information does not specify a calibration certificate as part of standard delivery Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.46mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ultra‑fine tolerance and workshop‑ready handling for dependable inspection results: the combination of ±0.001 mm accuracy, a 9.46 mm diameter and a 50 mm length ensures reproducible end‑measurements and tight fit checks. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for technical guidance. M323.946 — Gauge pin, 9.46 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.946 is a single gauge pin designed for high‑precision end‑measurement and inspection tasks in workshop and quality‑control environments High precision ±0.001 mm Diameter 9.46 mm for tight fits Length 50 mm workshop version Precision where micrometres matter This gauge pin delivers an exceptional ±0.001 mm tolerance (equivalent to 1 µm), a performance level that supports micrometre‑grade inspection and final acceptance checks. Such resolution reduces uncertainty when validating bore diameters or mating parts, which directly lowers the risk of rework and scrap in precision manufacturing. The declared accuracy is suitable for fine‑engineering tasks and quality control routines where repeatability and traceable results are essential. Compact dimensions that suit tight assemblies With a diameter of 9.46 mm and a 50 mm length, the pin fits small bores and narrow seats while offering enough engagement for stable measurement. The compact format is advantageous when checking end‑masses, alignment seats or plug‑fits in jigs and fixtures: the short but rigid form minimises bending and aids consistent positioning. At an optimized mass of 0.031 kg the component is easy to handle during serial inspection without compromising rigidity. Robust workshop construction for everyday use Manufactured from special steel in a workshop version, this single gauge pin is engineered for repeated handling and the mechanical stresses of production environments. The robust material choice supports dimensional stability over many cycles; surface finish and heat treatment are tailored to maintain running accuracy. Delivery includes a case for transport, protecting the pin in transit and storage and helping to preserve the calibrated condition between uses. Practical integration into quality procedures The pin is primarily intended for end‑measurement and plug‑gauge tasks within standard inspection workflows. It works well as a reference element in manual gauges, go/no‑go fixtures or as a check piece in small assembly lines. Metav IndustryLine components emphasise accessible precision: the M323.946 provides a straightforward way to upskill routine inspections with a measurable improvement in process reliability and first‑pass yield. Contact Metav Werkzeuge for specific advice on implementing the Metav IndustryLine M323.946 gauge pin in inspection routines or to request a product datasheet via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.946 GTIN: 4061905064975 Brand: Metav IndustryLine Facts Diameter: 9.46 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.031 kg Special features Material: special steel Workshop version Single gauge pin for end‑measurement Delivered in a case for transport FAQ What is the measurement tolerance of this gauge pin? The M323.946 gauge pin is manufactured to a tolerance of ±0.001 mm, suitable for micrometre‑accurate end‑measurements. Which applications are typical for this pin? Typical uses include plug‑fit checks, end‑measurement of bores and seating checks in jigs and fixtures for precision engineering and quality control. Is the pin supplied ready for transport? Yes, the gauge pin is supplied in a protective case for transport, which helps preserve its condition during storage and movement. Which material is used for the pin? The M323.946 is made from special steel, chosen to provide dimensional stability and robustness for workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.47mm Gauge Pin, Single, ±0.001mm Tolerance, 50mm Length, Workshop Version - Metav IndustryLine
Precision checks benefit from the combination of sub‑micrometre control and a robust workshop design: a 9.47 mm diameter finished pin with ±0.001 mm tolerance and a 50 mm shank length delivers repeatable end‑dimension verification. Order directly via Metav Werkzeuge or consult our technical team for application support. Gauge pin M323.947 (single test pin) — 9.47 mm, ±0.001 mm A gauge pin M323.947 designed for exact end‑dimension checks in workshop and inspection settings Workshop version for robust use Diameter precisely 9.47 mm Tolerance ±0.001 mm Length 50 mm for standard fixtures Consistent end‑dimension verification for tight tolerances Designed for metrology and workshop inspection, this single gauge pin offers ±0.001 mm repeatability, making it suitable where tight end‑measurement control is required. The nominal 9.47 mm diameter is produced to a high surface finish and concentricity, which reduces measurement scatter when seated in bushings or fixtures. In practice, this level of tolerance minimises rework and inspection time because parts can be validated against a stable reference element rather than inferred from indirect measurements. The numeric precision is particularly valuable in small‑part manufacture and prototype inspection where dimensional deviations immediately affect assembly fit. Robust construction that supports everyday workshop use The pin is made from special steel, engineered for wear resistance and dimensional stability under regular handling. A 50 mm working length provides sufficient engagement in common locating holes and fixture bores while remaining compact for manual placement and automated stations alike. The "workshop" specification signals an emphasis on durability and usability: hardened contact zones and a corrosion‑resistant finish extend service life and maintain repeatability over many inspection cycles. For users replacing worn check pins or upgrading legacy test sets, the robust construction reduces downtime and keeps inspection throughput steady. Practical integration into inspection jigs and gauges Produced as a single, traceable test element, the pin suits direct insertion into pin jigs, plug gauges and fixture assemblies where a defined end stop is needed. The precise diameter and length combination simplifies fixture set‑up and reduces the need for additional shims or adjustments. For batch quality control, several pins of the same nominal size can be interchangeably used to verify bores, counterbores and mating features, ensuring reproducible pass/fail decisions. Where documentation is required, the SKU and GTIN provide unambiguous identification for records and procurement. Contact Metav Werkzeuge for tailor‑made advice on applying this Metav IndustryLine gauge pin in specific inspection workflows — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.947 GTIN: 4061905064982 ECLASS: 21170231 Brand: Metav IndustryLine Facts Diameter: 9.47 mm Length: 50 mm Permissible deviation: ±0.001 mm Weight: 0.031 kg Special features Workshop execution Material: special steel Single gauge pin for end‑dimension checks Application trigger: end measurement FAQ What tolerance is achieved with this gauge pin? The gauge pin M323.947 is manufactured to a tolerance of ±0.001 mm, suitable for high‑precision end‑dimension verification. Which diameter and length does the pin have? This test pin has a diameter of 9.47 mm and a shank length of 50 mm, matching common fixture and gauge requirements. What material is used and how does it affect service life? Made from special steel, the pin combines hardness and wear resistance to preserve dimensional stability during repeated inspections. For which inspection tasks is this pin intended? The pin is intended for direct end‑dimension checks, plug gauge uses and locating operations in workshop and small‑scale production metrology. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.48mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop-ready robustness combined with ±0.001 mm dimensional accuracy and a precise 9.48 mm reference diameter for repeatable end-measure checks; the 50 mm length ensures stable seating in fixtures. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification matching. Gauge pin M323.948 (Metav IndustryLine) – 9.48 mm, ±0.001 mm tolerance The gauge pin M323.948 is a workshop-grade reference pin for precise end-measure checks and fit verification in toolmaking, inspection and fixture set-up. Workshop-grade design for daily use Diameter 9.48 mm with ±0.001 mm accuracy 50 mm reference length for fixture checks Special steel construction for durability Repeatable precision for critical fits The gauge pin delivers ±0.001 mm positional consistency, making it suitable where tight tolerances matter in go/no-go verifications and reference measurements. The specified 9.48 mm diameter is manufactured to a fine tolerance band so that positional references and mating fits remain reproducible across repeated cycles. By reducing measurement uncertainty at the reference stage, downstream assembly and closing operations benefit from fewer rework loops and predictable clearance behaviour. The tolerance is expressed as a deviation limit to align with industrial inspection practices rather than a marketing claim. Built for workshop use and long-term stability Constructed from special steel, the pin combines surface hardness with dimensional stability to withstand routine handling and contact in a busy workshop environment. The 50 mm reference length provides a secure seating depth for fixture and datum contacts, reducing the influence of operator handling on the measurement result. The workshop‑grade execution prioritises abrasion resistance and consistent geometry, so the reference element keeps its form as a reliable datum over time and repeated insertion cycles. Practical integration into inspection and tooling workflows Designed as a single reference element, this precision plug is suitable for end-measure checks, alignment of jigs and verification of bore positions where a compact, accurately sized reference is required. The compact mass and balanced geometry support quick placement in fixture bores and locating holes while maintaining positional fidelity. Traceable identification via SKU and GTIN simplifies inventory and process documentation, supporting quality records and component tracking in standard inspection routines. Request a technical consultation with Metav Werkzeuge in Emmerich to confirm suitability for specific fixtures or measurement programmes and to secure the M323.948 as the workshop reference pin for repeatable inspection results Technical data Article number: M323.948 GTIN: 4061905064999 Label: Prüfstift, einzeln, 9,48mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 9.48 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.031 kg Special features Workshop‑grade execution Material: Special steel Single precision gauge pin SKU: M323.948 FAQ What level of dimensional control does this gauge pin provide? The Metav IndustryLine gauge pin M323.948 is manufactured to a tolerance of ±0.001 mm, offering high repeatability for precision fit and end-measure checks. Can this pin be used for fixture set-up and alignment? Yes, the 50 mm length and precise 9.48 mm diameter make the reference pin suitable for fixture alignment and locating operations in workshop environments. What material is the pin made from and why does it matter? The pin is made of special steel, chosen for its wear resistance and dimensional stability so the reference stays consistent during repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.49mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Finish, Special Steel - Metav IndustryLine
Benefit from sub‑micrometre repeatability thanks to ±0.001 mm tolerance, a nominal diameter of 9.49 mm and a compact 50 mm length that fits inspection jigs and end‑measure checks; supplied in a transport case for secure handling. Order directly via Metav Werkzeuge or consult our specialists for application advice. Measuring pin M323.949 — single gauge pin, 9.49 mm, ±0.001 mm (50 mm length) — Metav IndustryLine The Measuring pin M323.949 is a precision gauge pin designed for reliable end‑measurements and verification tasks in workshop and inspection environments Workshop version for robust use Diameter 9.49 mm with ±0.001 mm tolerance Length 50 mm for end‑measurement tasks Delivered in transport case for safe handling Consistent, evidence‑based accuracy for quality control The compact precision pin delivers a tolerance of ±0.001 mm, which supports fine inspection routines and dimensional verification where deviations must be tightly controlled. This level of accuracy reduces rework and scrap by enabling rapid, reproducible check steps at the measuring station. The specification refers to the intrinsic manufacturing tolerance of the pin; repeat measurements with a stable holding fixture will expose the true performance in a production setting. For traceability, the nominal diameter of 9.49 mm is suited to reference gauges and comparators used in dedicated measuring benches. Robust workshop design that stands up to daily use Built as a workshop version, the pin is manufactured from special steel to withstand handling and contact with seating bores, jigs and fixtures. The 50 mm overall length offers a practical balance between reach and rigidity, keeping deflection minimal during insertion and withdrawal. The robust finish and material choice mean longer service intervals before replacement is required, so maintenance cycles and tool lists remain predictable. Where frequent checks are carried out on the shop floor, this durability translates into less downtime and fewer interrupted production checks. Practical handling, protection and integration into inspection routines Supplied in a transport case, the pin arrives protected against knocks and surface damage; this simplifies storage and keeps the reference surface pristine until first use. The compact form factor integrates easily into existing gauge sets, inspection trays or fixture pockets. For operators, the modest mass ensures the pin can be positioned quickly while the defined contact surfaces reduce variation caused by inconsistent placement. Where a controlled handling procedure exists, adding the pin to the inspection kit improves workflow efficiency and measurement reliability. Where this precision pin benefits production and quality assurance This gauge pin suits end‑measure checks, go/no‑go fixtures and dimensional verification of mating bores. The narrow tolerance window is particularly valuable when parts enter assembly lines that demand tight fitment or when batch acceptance relies on quick comparative checks. Using a stable gauge with known characteristics supports documented quality processes and reduces subjective judgement during manual inspections. In short, the component is a practical tool for anyone who needs compact, repeatable verification in a workshop context. Contact Metav Werkzeuge GmbH in Emmerich for tailored advice on integrating the M323.949 into inspection setups and to confirm availability and packaging options Technical data SKU: M323.949 GTIN: 4061905065842 ECLASS: 21170231 Core measurements Nominal diameter: 9.49 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.031 kg Materials & special features Material: Special steel Version: Workshop execution Delivery: Transport case included Typical application: End measurements / verification FAQ What tolerance can be expected from this measuring pin? The M323.949 measuring pin is specified with a tolerance of ±0.001 mm, providing tight dimensional control for verification tasks. Is the pin suitable for use in a production inspection fixture? Yes; this single gauge pin from Metav IndustryLine is designed as a workshop version and integrates well into fixtures for repeated end‑measure checks. How is the pin delivered and protected during transport? Delivery includes a transport case, which protects the reference surfaces and simplifies storage until the pin is placed into the inspection kit. What material is used for the pin and why does it matter? The pin is made of special steel, chosen for wear resistance and dimensional stability under regular handling in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.4mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combining ±0.001 mm accuracy with a 9.40 mm diameter and a 50 mm length, this single gauge pin delivers repeatable end‑measurement results in workshop inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. M323.940 gauge pin (Workshop‑grade, ±0.001 mm accuracy) M323.940 is a single, workshop‑grade gauge pin designed for precise end‑measurements and repeatable inspection tasks in metalworking and quality control environments. ±0.001 mm tolerance for fine control 9.40 mm diameter in a 50 mm length Special steel construction for durability Workshop execution for everyday use High precision for dependable end‑measurements This gauge pin is engineered to provide a consistent reference when checking final dimensions. With a ±0.001 mm tolerance and a nominal 9.40 mm diameter, the component reduces ambiguity in acceptance decisions and supports tighter control limits. The 50 mm shank offers adequate reach for typical inspection set‑ups while keeping handling simple; the result is fewer rechecks and more efficient throughput in small‑to‑medium production runs. By focusing on measurable performance, the pin helps to cut scrap and rework rates through reliable, repeatable checks. Robust design that suits workshop routines Built as a workshop‑grade tool from special steel, the measuring pin withstands frequent use at bench and in jig setups. The single‑piece configuration minimises play and surfaces are finished to ensure stable seating in holders and gauges. This robustness translates into stable contact conditions and therefore improved repeatability, even under routine use. The modest weight and compact geometry make it straightforward to position by hand or in fixtures, supporting quick inspection cycles without sacrificing measurement integrity. Integrates with inspection workflows and documentation The gauge pin is ideal as a fixed reference in quality assurance procedures, integration into go/no‑go fixtures, or as a reference in manual gauging sequences. Its clear specification—diameter, length and tolerance—simplifies documentation and traceability in inspection reports and reduces the chance of ambiguity during handovers between shifts. When paired with structured inspection plans, the pin supports consistent decision making and helps maintain an auditable measurement record across production stages. For reliable workshop measurements with Metav IndustryLine precision, contact Metav Werkzeuge to request advice or to arrange supply of this 9.40 mm, ±0.001 mm gauge pin — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.940 GTIN: 4061905063893 Label: Prüfstift, einzeln, 9,40mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 9.40 mm Length: 50 mm Tolerance (accuracy): ±0.001 mm Weight: 0.031 kg Special features Material: Special steel Workshop execution Single test pin FAQ What tolerance does the gauge pin offer? The gauge pin is specified with an accuracy of ±0.001 mm, suitable for fine end‑measurement tasks in inspection routines. What are the physical dimensions of the pin? The pin has a diameter of 9.40 mm and a length of 50 mm; it is listed under SKU M323.940. Is the item supplied individually or in sets? This is supplied as a single test pin, designed for insertion into fixtures or use as a standalone reference in workshop checks. Which materials and environments is the pin designed for? Manufactured from special steel and offered in a workshop execution, the pin is suitable for routine use in metalworking inspection and general quality control tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.51mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of the combination of industrial accuracy, compact handling and robust construction to keep inspection routines fast and reliable; the ±0.001 mm tolerance, Ø 9.51 mm diameter and 50 mm length ensure repeatable end‑dimension checks. Order the test pin directly via Metav Werkzeuge or request guidance from our consultants for specification matching. Test pin M323.951 — single workshop‑grade gauging pin, Ø 9.51 mm, ±0.001 mm Test pin M323.951 is a workshop‑grade precision gauging pin designed for end‑dimension inspection and quick verification tasks in production and quality control. Workshop‑grade precision ±0.001 mm Diameter Ø 9.51 mm for end measurements Special steel construction Length 50 mm for compact probing Precision that reduces rework and downtime The gauge delivers a certified ±0.001 mm tolerance that supports high‑accuracy quality checks in repetitive production processes. Such fine tolerance minimises the risk of assembly problems and downstream rework by ensuring that measured end dimensions are reliably within specification. Where batch consistency is critical, the stable measuring diameter and predictable fit help reduce cycle‑time losses caused by trial‑and‑error adjustments. This performance argument targets efficiency and fewer production interruptions rather than abstract quality claims. Practical design for everyday inspection tasks With a nominal diameter of 9.51 mm and a length of 50 mm, the pin is compact enough for manual probing and robust enough to be used in common inspection jigs. The workshop classification indicates suitability for routine shop‑floor use: fast handling, simple seating in fixture bores and clear tactile feedback during checks. The single‑piece construction avoids alignment ambiguity common to multi‑component probes, making gauging operations more straightforward and reducing measurement variability in typical machine‑shop environments. Material choice that supports longevity in the workshop Constructed from special steel, the pin combines dimensional stability with resistance to everyday wear. The chosen material maintains geometry under repeated contact and contributes to a long service life when used for comparative gauging and end‑dimension verification. Low mass (0.032 kg) keeps handling comfortable during frequent checks and lowers operator fatigue in high‑throughput inspection routines, supporting sustained accuracy across many cycles. Traceability and straightforward inventory integration The article is catalogue‑ready for industrial procurement: it carries a clear SKU and GTIN for stock control and ordering, facilitating integration into tool cabinets and inspection kits. Lightweight handling and compact size make storage and deployment efficient in busy inspection benches. For tailored advice on fixture compatibility or batch requirements, Metav’s technical team can provide specification guidance and help select complementary gauging accessories. Request Metav Werkzeuge’s technical advice for seamless integration of the Metav IndustryLine test pin M323.951 into existing inspection workflows and ensure the correct probe selection for critical tolerance checks Technical data Article number: M323.951 GTIN: 4061905065866 ECLASS: 21170231 Product label: Test pin, single, Ø 9.51 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 9.51 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.032 kg Messbereich (measuring size): 9.51 mm Special features / Materials Material: Special steel Workshop version Single‑piece test pin GTIN for traceability FAQ What tolerance does this test pin offer? The test pin M323.951 is specified with a tolerance of ±0.001 mm to support precise end‑dimension checks. What are the pin dimensions and how do they affect use? The pin has a diameter of 9.51 mm and a length of 50 mm; these dimensions make it suitable for compact probing and quick verification in fixtures and manual checks. Is the material suitable for regular shop‑floor use? Yes, the M323.951 is made from special steel, selected to provide dimensional stability and wear resistance appropriate for routine inspection tasks. How can this article be ordered or identified in inventory systems? The test pin is listed as M323.951 and carries GTIN 4061905065866 for straightforward ordering and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com