Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
80mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Combine the 80 mm diameter with hardened and lapped gauge steel and conformity to DIN 2250 for reproducible setting and calibration results; order directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Gauge Ring M313.080 — 80 mm hardened gauge steel, DIN 2250 The Gauge Ring M313.080 serves as a precision reference ring for setting, calibration and go/no-go verification tasks in workshop and metrology environments. 80 mm nominal diameter, precision-ground Hardened and lapped gauge steel Conforms to DIN 2250 / DIN 286, JS 3 Designed in Form C for stable seating Faster, repeatable setups through precise reference geometry The ring’s 80 mm nominal diameter and hardened and lapped gauge steel surface provide a stable reference that reduces set-up times and minimises rework. As a precision reference, the component supplies a fixed datum for calibre adjustment and tool setting, so fixtures and gauges can be adjusted consistently across production runs. The lapped finish lowers contact wear and helps maintain dimensional integrity over repeated use, delivering measurable productivity gains during routine calibration and inspection cycles. Standards-based tolerance that professionals can rely on Manufactured to DIN 2250 and DIN 286 with JS 3 tolerance, the reference ring offers explicitly defined limits for deviation, making it straightforward to integrate into quality procedures. The specified tolerance class communicates the expected dimensional variation and supports traceable decision-making in quality control. This standards-driven approach ensures compatibility with existing inspection equipment and allows engineers to document conformity in audits without additional interpretation or qualification. Practical handling and workshop applications for reliable measurement control The ring’s Form C design ensures positive seating and simple alignment during use, suitable for setting internal gauges, checking plug and ring gauge interfaces, or verifying bores. As a compact, robust reference, it is particularly useful in maintenance shops, tool rooms and inspection benches where repeatability is essential. Clear identification via SKU and GTIN simplifies inventory management and procurement, while the proven material and finish reduce the frequency of recalibration and replacement, supporting uninterrupted production and fewer measurement-related stoppages. Contact Metav Werkzeuge today for tailored advice on using the Metav IndustryLine gauge ring M313.080 in calibration workflows, or to request stock and delivery information via +49 2822 7131930 or info@metav-werkzeuge.com Technical Data SKU: M313.080 GTIN: 4054469120959 eClass: 21170104 Facts Diameter: 80 mm Customs tariff number: 90173000 Special features Hardened and lapped gauge steel Form C DIN 2250 and DIN 286, JS 3 Category: Gauge / Setting ring FAQ What is the intended use of this gauge ring? The Metav IndustryLine gauge ring M313.080 is intended as a precision reference for setting, calibration and go/no-go verifications on internal diameters and for gauge adjustment. Which standards does the ring comply with? The ring conforms to DIN 2250 and DIN 286 with the JS 3 tolerance class, ensuring compatibility with standard inspection practices. Is the surface finish suitable for repeated calibration use? Yes; the ring’s hardened and lapped gauge steel finish reduces surface wear and maintains dimensional stability for repeated calibration cycles. Can this ring be used in an inspection laboratory as a reference standard? The Metav IndustryLine M313.080 is suitable as a workshop and inspection reference for routine calibration; for laboratory accreditation needs, please request specific calibration documentation from Metav Werkzeuge. How can the item be identified for ordering or inventory? Reference SKU M313.080 and GTIN 4054469120959 when ordering or recording the item in inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
82 mm Limit Go/No-Go Plug Gauge H7 Hardened Gauge Steel DIN 2245 - Metav IndustryLine
Data conflict detected: the product weight is inconsistent — the label states 2.6 kg but the weight field shows 3 kg. This discrepancy raises concerns about the accuracy of the information provided. It is essential to ensure that all product details are consistent and verified to maintain credibility and avoid confusion for customers. Please verify the source data thoroughly before publishing a product description. Cross-check the label information with the weight field and any other relevant documentation to confirm the correct weight. Accurate data is crucial for customer trust and smooth operations.
82mm Setting Ring, Hardened Gauge Steel, Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the combination of precise tolerances, hardened and lapped gauge steel, and DIN-compliant manufacture for reliable setting and inspection results; order the setting ring directly via Metav Werkzeuge or contact our consultants for technical advice. Setting ring 82 mm (Form C) — hardened, lapped gauge steel, DIN 2250 The setting ring 82 mm is a hardened ring gauge for accurate reference and setting tasks in inspection, workshop and production environments. 82 mm nominal diameter, Form C Hardened and lapped gauge steel DIN 2250 / DIN 286, tolerance JS 3 Repeatable setting for production efficiency A ring gauge with a defined nominal diameter delivers fast and repeatable set‑ups for tool presetters, spindle probes and go/no‑go checks. The 82 mm nominal size offers a compact reference that reduces handling time while maintaining position stability; users benefit from quicker machine changeovers and consistent zeroing of measuring devices. The lapped finish minimises surface irregularities, supporting a clear tactile reference and reducing the risk of inconsistent contact during repeated use. Standards-based accuracy that supports quality control Manufactured to DIN 2250 and DIN 286 with tolerance class JS 3, this ring gauge supplies a measurable basis for dimensional control and traceable inspection routines. Conformance to these standards means the component can be integrated into calibration chains and inspection plans, helping to document compliance during audits. Clear numeric tolerances simplify decision‑making in quality inspection and reduce downtime caused by uncertain reference parts. Durable material and finish for long service life Produced from gauge steel, then hardened and lapped, the component resists wear and preserves its form under frequent contact. The combination of heat treatment and fine finishing ensures the ring keeps its reference diameter over many cycles, which lowers the frequency of replacements and helps maintain stable process capability. The robust construction supports everyday workshop handling without sacrificing metrological stability. Practical integration into workshop workflows Thanks to a compact form and defined geometry (Form C), the setting ring is straightforward to handle and store on trolleys, in instrument cabinets or next to presetting stations. Its design streamlines routine checks and reduces time spent searching for a suitable reference during set‑up procedures. Whether used at a workbench, in a tool room or at an incoming inspection desk, the component supports efficient, defensible measurement practice. Choose the Metav IndustryLine setting ring for dependable gauge control and contact Metav Werkzeuge in Emmerich for delivery and expert advice: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M313.082 GTIN: 4054469120966 eClass: 21170104 Tariff number: 90173000 Core specifications Nominal diameter: 82 mm Form: C Tolerance class: JS 3 Materials & features Material: gauge steel, hardened and lapped Standards: DIN 2250; DIN 286 Category: gauges / ring gauge FAQ What measurement tasks is this ring gauge designed for? The setting ring 82 mm serves as a reference for setting and checking diameters, enabling reliable zeroing and go/no‑go inspections in the workshop and inspection lab. How precise is the ring in terms of tolerance? Manufactured to tolerance class JS 3 and compliant with DIN 2250 and DIN 286, the ring provides a defined tolerance suitable for routine dimensional control and setting work. What material and surface treatment does it have? The ring is made from gauge steel, hardened and lapped, providing wear resistance and a stable reference surface for repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
85 mm Go/No-Go Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of a hardened gauge steel construction combined with DIN 2245 accuracy and an 85.0 mm nominal diameter to ensure repeatable bore verification in production and inspection. Order the gauge directly via Metav Werkzeuge or consult the technical team for specification matching. M314.085 limit plug gauge — 85.0 mm H7, DIN 2245 (Metav IndustryLine) A M314.085 limit plug gauge designed for fast verification of bore diameters to DIN 2245 tolerance H7, suited to workshop and inspection use Hardened gauge steel for long service life Manufactured to DIN 2245 H7 tolerance Nominal diameter 85.0 mm for bore inspection Robust construction for regular shop‑floor use Consistent bore verification with standardised tolerances The M314.085 is manufactured to DIN 2245 and finished to an H7 tolerance, providing a clear, measurable basis for acceptance testing of cylindrical bores. The gauge’s 85.0 mm nominal diameter corresponds to established tolerance bands, allowing rapid conformity checks without interpretation. Because measurements rely on mechanical fit rather than electronic readouts, inspection decisions become straightforward and repeatable, reducing ambiguity in incoming parts inspection and inline quality control. Durable materials and workshop suitability Made from gauge steel, hardened, this limit plug gauge resists wear and preserves functional dimensions under frequent use. The hardened surface reduces edge degradation and maintains the intended gauge form across many inspection cycles, which lowers the need for frequent replacement and supports a stable inspection routine. The solid construction also makes the item suitable for direct use at assembly benches and in toolrooms, where simple, robust verification tools are preferred. Practical integration into quality processes As a purpose‑built limit gauge, the device supports go/no‑go style verification workflows and can be incorporated into first‑article inspection or routine process control. Traceable identification via the listed GTIN and article code simplifies inventory and quality records. The clear conformity to DIN standards helps align measurement practices with contractual and normative requirements, aiding certification and internal quality audits while streamlining operator training. Why this gauge adds value to manufacturing operations Using a standardised mechanical gauge reduces dependency on recalibration cycles required by some measurement systems and offers an immediate pass/fail decision that speeds throughput. The combination of recognised standard conformity, hardened material and a nominal size commonly used in engineering makes the instrument a cost‑effective choice for repeatable bore verification, particularly where simple, fast acceptance checks are needed. For availability and expert advice on the Metav IndustryLine M314.085 limit plug gauge, contact Metav Werkzeuge in Emmerich by e‑mail or phone to discuss suitability and delivery options Technical Data Article number: M314.085 GTIN: 4054469121888 Norm: DIN 2245 Nominal diameter: 85.0 mm Data Tolerance: H7 Tariff code: 90173000 Special features Material: gauge steel, hardened Category: limit plug gauge Brand: Metav IndustryLine FAQ What is the M314.085 used for? The M314.085 limit plug gauge is used for quick go/no‑go verification of cylindrical bores to the DIN 2245 H7 specification. Is the gauge suitable for shop‑floor use? Yes, the hardened gauge steel construction of the M314.085 is intended for regular workshop and inspection use, offering robust performance in production environments. Which standard does this plug gauge comply with? This plug gauge is manufactured to DIN 2245 and finished to an H7 tolerance for standardised bore inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
85mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of DIN 2250 / DIN 286 conformity, a hardened and lapped gauge-steel finish and the compact 85 mm reference diameter to secure reproducible setting and inspection results; order the setting ring directly via Metav Werkzeuge or consult our specialists for further advice. Setting ring 85 mm — hardened, lapped gauge-steel reference (Metav IndustryLine) A Setting ring 85 mm designed as a precision reference for tool setting, inspection fixtures and calibration workflows in workshop and quality environments. DIN 2250 / DIN 286, tolerance JS 3 Hardened and lapped gauge steel Precise 85 mm diameter reference Form C geometry for stable mounting Precision reference that reduces setup uncertainty The compact ring provides a consistent, traceable reference for setting internal diameters and calibrating measuring devices. Manufactured from gauge steel, then hardened and lapped, the component offers surface integrity and dimensional stability that translate into lower setup variation and fewer reworks. Conformity with DIN 2250 and DIN 286 at JS 3 tolerance ensures the ring serves as a reliable datum in production and inspection loops, supporting repeatable alignment and correct fixture adjustment. Solid construction for dependable, long-term use A robust geometry in Form C keeps the reference stable during handling and mounting, while the lapped finish reduces wear on contact faces. The combination of material choice and surface treatment delivers high resistance to abrasion and correct seating in ring holders or test benches. As a workshop-grade gauge from Metav IndustryLine, the component is intended for frequent use where quick, reproducible checks are required without compromising on accuracy. Designed for smooth integration into inspection routines The ring’s nominal 85 mm diameter matches common tool-setting and inspection requirements, enabling direct use as a calibration master or as a setup aid in production cells. Clear standardisation to recognised norms simplifies documentation and audit processes, while the compact form factor makes storage and handling straightforward. Where traceability is required, the ring’s standards-based specification supports routine verification and straightforward recording in quality management systems. Choose the Metav IndustryLine setting ring for standardised, robust setting references — contact Metav Werkzeuge for availability and tailored advice. Technical Data Article number: M313.085 GTIN: 4054469120973 Manufacturer: Metav IndustryLine Facts Diameter: 85 mm Tolerance: JS 3 (DIN 2250 / DIN 286) Tariff code: 90173000 Special features Material: gauge steel, hardened and lapped Form: C eClass: 21170104 FAQ What accuracy class does the setting ring meet? The setting ring meets tolerance class JS 3 according to DIN 2250 and DIN 286, providing a standardised accuracy level for workshop and inspection use. Can the ring be used for tool setting and calibration? Yes. The Setting ring 85 mm from Metav IndustryLine is intended as a precision reference for tool setting and routine calibration tasks. What material and surface finish does the ring have? The ring is made from gauge steel, hardened and lapped to provide durable, wear-resistant contact faces suitable for frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
87mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of a DIN 2250‑compliant ring gauge that combines hardened, lapped gauge steel with a tight JS 3 tolerance for reliable setting and inspection; the 87 mm diameter and robust Form C design ensure repeatable fits in workshop and inspection tasks. Order the setting ring directly via Metav Werkzeuge or consult our specialists for application advice. Setting ring gauge 87 mm (DIN 2250) — hardened, lapped gauge steel (Metav IndustryLine) The Setting ring gauge 87 mm is a precision ring for setting and checking fit dimensions in inspection and production environments, suitable where repeatable reference diameters are required Hardened, lapped gauge steel Diameter 87 mm to DIN 2250 Tolerance class JS 3 for repeatable fits Form C configuration for ring gauge use Repeatable reference for set‑up and inspection A purpose‑made setting ring gauge provides a stable reference diameter for tool set‑up, go/no‑go fixtures and comparative checks. Manufactured to DIN 2250 and matched with DIN 286 tolerance practice, the component achieves the JS 3 tolerance grade, which translates into consistent seating and interchangeability when used as a datum for gauges or fixtures. The combination of a hardened, wear‑resistant surface and a lapped finish reduces contact variability, so measurement uncertainty from surface irregularities is minimised and process repeatability improves. Robust material and geometry for workshop durability Constructed from hardened and lapped gauge steel, the ring resists wear under frequent use while maintaining the accuracy required for routine production control. The Form C geometry offers a practical handling profile and stable seating in ring gauge holders or test benches; at 87 mm diameter the part balances mass and rigidity, delivering a stable reference without excessive bulk. The measured weight of 1.7 kg contributes to handling stability during use and reduces the risk of movement that can impair checks. Practical applications and integration into inspection routines This type of ring is well suited for calibration jigs, setting mandrels and comparative checks in mechanical workshops, toolrooms and quality departments. The standardised dimensions and tolerance class make it straightforward to integrate the ring into existing gauge sets or fixture systems, supporting consistent set‑ups across multiple machines and operators. Where traceable, repeatable references are required for process control, the ring functions as a compact, robust means to reduce downtime caused by imprecise set‑up. Contact Metav Werkzeuge to discuss integrating the Metav IndustryLine 87 mm setting ring into inspection procedures or to request tailored advice for specific gauge‑setups and fixture compatibility. Technical data Article number: M313.087 GTIN: 4054469179230 Weight: 1.7 kg Diameter: 87 mm Material: gauge steel, hardened and lapped Standards: DIN 2250; DIN 286, JS 3 Special form: Form C Tariff number: 90173000 Facts Diameter: 87 mm Weight: 1.7 kg Tolerance class: JS 3 Standards: DIN 2250 / DIN 286 GTIN: 4054469179230 Special features Hardened gauge steel, lapped finish Form C design Intended for setting and inspection use Category: Gauges / Setting rings Manufacturer: Metav IndustryLine FAQ What is the intended use of this setting ring? The setting ring M313.087 from Metav IndustryLine is intended as a precision reference for setting, checking and comparative measurements where an 87 mm datum is required. Which standards does the ring comply with? The ring is manufactured to DIN 2250 and referenced by DIN 286, with a tolerance level of JS 3, ensuring conformity with common metrology practices for ring gauges. Is the material suitable for frequent workshop use? Yes. The ring is made from hardened and lapped gauge steel, a combination chosen to resist wear and preserve dimensional stability under regular handling and contact checks. Can the ring be integrated into existing gauge sets and fixtures? Integration is straightforward: the standardised diameter and JS 3 tolerance make the product compatible with common ring holders and fixture systems used in inspection and tool‑setting routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
88 mm Limit Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of the combination of DIN 2245 conformity, hardened gauge steel, and fast go/no‑go verification to secure consistent bore quality and minimise production rejects; order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Limit plug gauge M314.088 — 88.0 mm, DIN 2245 H7 (Metav IndustryLine) The limit plug gauge M314.088 offers straightforward Go/No‑Go checking of 88.0 mm cylindrical bores for production and inspection environments Hardened gauge steel construction Complies with DIN 2245 H7 tolerance Designed for quick Go/No‑Go verification Metav IndustryLine quality control Ensure repeatable acceptance testing on the shop floor A compact inspection gauge designed for routine diameter verification, the limit plug gauge secures process reliability by delivering immediate pass/fail information. The standardised DIN 2245 form and H7 tolerance simplify communication with suppliers and inspection plans, while the go/no‑go principle removes interpretation time. This direct check reduces rework and supports lean production by flagging non‑conforming parts before they progress along the line. Built for long service life and stable results Constructed from hardened gauge steel, the gauge resists wear and maintains form under frequent handling, which preserves precision across many inspection cycles. The robust material choice and standardised design reduce drift and help keep measurement uncertainty low, so results remain comparable between operators and shifts. The Metav IndustryLine manufacturing control provides consistent finishing and traceability for inspection tools used in industrial environments. How the standard and tolerance translate into everyday benefits The designation H7 denotes the tolerance band relevant for bore acceptance, and when combined with the DIN 2245 profile it guarantees interchangeability in serial production. The 88.0 mm dimension is checked by the solid plug form: the "go" end confirms minimum material removal has been achieved, while the "no‑go" end ensures the bore has not exceeded the upper limit. For quality assurance teams this means fewer measurement steps, faster cycle times and clearer conformity documentation when comparing parts to drawings. Practical integration into quality workflows This inspection plug is suitable for in‑process checks at machine centres, incoming inspection of supplier batches, and final inspection benches where quick decisions are required. Its straightforward function supports training of new technicians and simplifies routine audits. Where traceable documentation or stricter laboratory calibration is required, Metav Werkzeuge can advise on the appropriate inspection routines and complementary gauges to form a practical test set. For assured bore acceptance testing with Metav IndustryLine gauges such as M314.088, contact Metav Werkzeuge for application advice and availability from their Emmerich centre Technical data SKU: M314.088 GTIN: 4054469121895 Standard: DIN 2245 Material: gauge steel, hardened Brand: Metav IndustryLine Core measurements Diameter: 88.0 mm Tolerance: H7 Tariff number: 90173000 Materials & features Type: limit plug gauge (go/no‑go) Category: inspection gauges / plug gauges ECLASS: 21170218 FAQ What is the primary use of this plug gauge? The limit plug gauge M314.088 is used for rapid Go/No‑Go verification of 88.0 mm bores to confirm conformance with the H7 tolerance band. Which standard applies to the design of this gauge? The gauge is manufactured to DIN 2245, ensuring the profile and functional dimensions match common inspection requirements. Is the gauge suitable for frequent shopfloor checks? Yes; the hardened gauge steel construction and Metav IndustryLine production quality make the M314.088 appropriate for regular in‑process and incoming inspection use. Does this product include calibration documentation? No ISO 17025 certificate is indicated for this item; standard factory inspection applies. For traceable laboratory calibration options, Metav Werkzeuge can provide guidance. Can this gauge be used to document acceptance for serial parts? The plug gauge provides objective pass/fail results for production lots; when combined with documented inspection routines it supports serial acceptance procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
88mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the combination of hardened, lapped gauge steel, certified tolerances and robust mass for reproducible set‑ups and long service life; order the setting ring directly via Metav Werkzeuge or consult our specialists for application advice. Setting Ring 88 mm — Hardened gauge steel, DIN 2250 compliant (Metav IndustryLine) The Setting Ring 88 mm is a precision ring gauge designed for go/no‑go verification and instrument setting in workshop and inspection environments. Hardened, lapped gauge steel Conforms to DIN 2250 and DIN 286, JS 3 Form C geometry for secure seating Precise 88 mm diameter, weight 1.7 kg Consistent accuracy for routine inspection The Setting Ring 88 mm is manufactured from hardened, lapped gauge steel, delivering a stable contact surface that resists wear and maintains form accuracy over many measurement cycles. Conformance to DIN 2250 and DIN 286 with JS 3 tolerance ensures this ring can be used as a reference for setting instruments and carrying out repeatable go/no‑go checks. The standardised tolerance class provides a verifiable basis for quality control routines and reduces uncertainty in comparative measurements. Robust geometry that supports reliable handling A compact, dense design with form C seating and a mass of 1.7 kg contributes to stable positioning during checks and minimises the influence of small operator movements. The material finish—lapped after hardening—reduces friction and protects mating gauges and measuring faces. This combination of material hardness and finishing translates into less frequent rework of the gauge, lower maintenance needs and consistent performance in both workshop and inspection‑room contexts. Practical integration into workshop workflows Designed as a purpose‑built ring gauge for setting and verification, the product simplifies the transfer of dimensional reference values to micrometers, calipers and comparators. Its precise 88 mm diameter and robust construction make it suitable for repetitive set‑up tasks where time‑efficient and reliable checks contribute directly to process stability. The ring’s standards compliance supports traceability within quality systems and eases documentation when integrating reference artefacts into inspection routines. For ordering or application guidance, contact Metav Werkzeuge to secure supply and advice for your inspection process; our Emmerich hub ensures reliable delivery and product verification Technical data Article number: M313.088 GTIN: 4054469120980 Customs tariff number: 90173000 EClass: 21170104 Facts Diameter: 88 mm Weight: 1.7 kg Form: C Special features Material: hardened and lapped gauge steel Standards: DIN 2250; DIN 286; JS 3 Intended use: ring gauge for setting and verification FAQ What tolerance class does this ring gauge meet? The ring gauge meets the requirements of DIN 2250 and DIN 286 with JS 3 tolerance, specified for the Metav IndustryLine Setting Ring 88 mm (SKU M313.088). Is the ring suitable for setting micrometers and comparators? Yes, the ring is intended as a reference for instrument setting and go/no‑go verification and is compatible with micrometers, comparators and precision calipers used in workshop inspection. What material and finish are used for durability? The ring is made from hardened, lapped gauge steel, a finish that offers wear resistance while preserving contact accuracy over repeated use. Will the ring tolerate everyday workshop use? The dense construction and form C seating provide stable handling and reduced sensitivity to incidental knocks, making it appropriate for routine workshop and inspection tasks. Are size and mass details available for fixture planning? Yes — the ring has a nominal diameter of 88 mm and a mass of 1.7 kg, values that assist with fixture design and handling considerations. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the combination of one‑micron accuracy, robust special steel construction and workshop‑ready handling for dependable in‑process checks; order the item directly via Metav Werkzeuge or contact our consultants for specification advice. M323.800 — Precision gauge pin, 8.00 mm, ±0.001 mm The M323.800 is a single precision gauge pin designed for end‑measurement and go/no‑go verification tasks in inspection benches and toolrooms. 8.00 mm nominal diameter, ±0.001 mm tolerance 50 mm usable length, workshop version Special steel for stable dimensional performance Supplied in protective transport case Consistent one‑micrometre accuracy for repeatable inspection results The gauge pin delivers a tolerance of ±0.001 mm (1 µm), which places it in the high‑precision range for routine dimensional verification. This level of accuracy reduces measurement uncertainty when checking mating bores, pin fits or end faces, enabling faster decision‑making on the shop floor and fewer downstream rework cycles. The 8.00 mm nominal diameter is produced to tight run‑out and concentricity standards, so each check contributes to a reproducible quality record rather than a single isolated measurement. Durable workshop construction that keeps gauges in service Manufactured in special steel, the pin is built for the demands of a production‑oriented environment while retaining metrological stability. The workshop version combines hardened surfaces with corrosion‑resistant finishing to withstand handling and routine use; this reduces the frequency of replacement and supports continuous production. Supplied in a protective transport case, the item arrives ready for safe storage and transit, lowering the risk of accidental damage and preserving the calibrated state between uses. Practical form factor for efficient handling and traceability With a usable length of 50 mm, the pin balances reach with rigidity, making it suitable for inspection fixtures and hand checks alike. As a single gauge pin, it integrates easily into pin gauges or fixture arrays for comparative measurements and end‑dimension verification. Traceability is supported through the included identifiers: M323.800 is supplied with a GTIN, aiding inventory control and quality documentation in regulated production environments. The compact weight and simple geometry also make it convenient to seat and remove without specialised tooling. For precision tasks that demand one‑micron reliability, contact Metav Werkzeuge to discuss how the Metav IndustryLine M323.800 gauge pin can be integrated into your inspection routine and supply chain. Technical data Article number: M323.800 GTIN: 4061905063121 Material: Special steel Nominal diameter: 8.00 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.024 kg Version: Workshop execution Packaging: Supplied in protective transport case Facts Diameter: 8.00 mm Accuracy: ±0.001 mm Usable length: 50 mm Weight: 0.024 kg Special features Single gauge pin for end‑measure checks Robust shop‑floor design Corrosion‑resistant finishing GTIN for traceability FAQ What is the intended use of this gauge pin? The M323.800 gauge pin is intended for end‑measurement, fit verification and reference checks on bores and corresponding mating parts in inspection and production settings. How precise is the M323.800 and what does ±0.001 mm mean in practice? A tolerance of ±0.001 mm denotes one‑micrometre precision; in practice this supports fine inspection limits and reduces ambiguity when validating tight fits or critical diameters. Is the pin suitable for routine shop‑floor use? Yes, the workshop execution and special steel construction ensure the pin withstands regular handling while maintaining dimensional stability. Does the product include protective packaging? The gauge pin is supplied in a protective transport case to prevent damage during storage and transport and to preserve measurement integrity. Can the M323.800 be used with inspection fixtures? The 50 mm usable length and standard geometry allow the pin to be mounted or seated in fixture arrays and pin gauge blocks for comparative and reference measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8–9mm Gauge Pin Set 100 Pieces 70mm Step 0.01mm Special Steel, Case - Metav IndustryLine
Data inconsistency detected: the product designation states "100 pieces" while the item count indicates 101; please verify the source data before generating a product description. This discrepancy may lead to confusion or errors in the final product listing, potentially impacting customer trust and satisfaction. It is crucial to ensure that the source data is accurate and consistent across all fields to avoid misrepresentation. Double-check the inventory records, product labels, and any associated documentation to confirm the correct quantity. Addressing this issue promptly will help maintain the integrity of the product description and prevent any misunderstandings during the sales process.
8–9mm Gauge Pin Set 21-Piece 70mm Step 0.05mm, Special Steel In Plastic Case - Metav IndustryLine
Take advantage of the combination of high repeatability, robust special steel construction and compact handling for reliable bore inspection — order the set directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin set M318.828 — 21-piece inspection pins, 8.00–9.00 mm, 0.05 mm steps (Metav IndustryLine) The Gauge pin set M318.828 is a 21-piece inspection set designed for fast, accurate bore checking and go/no-go verification in metalworking and quality control. 21 precision pins in 0.05 mm steps Diameter range 8.00–9.00 mm 70 mm length for deeper bore checks Supplied in protective case Precision that shortens inspection cycles This inspection set was developed to increase throughput in routine quality checks by offering consistent spacings and a fine 0.05 mm step size. The graduated diameters enable quick identification of nominal and out-of-tolerance bores, reducing the need for repeated measurements with callipers or micrometres. Thanks to the set’s narrow increments and sturdy design, measurement time is reduced while traceability of results is maintained. Robust material for workshop conditions Manufactured from special steel, each pin resists wear during repeated use, providing stable diameters over extended service life. The combination of hardness and surface finish supports reliable contact fit without rapid deterioration, which benefits maintenance intervals and lowers the total cost of ownership in production or toolroom environments. The material choice also ensures compatibility with common engineering metals when used for verification tasks. Practical geometry for real-world checks With a length of 70 mm, the pins reach into deeper bores where shorter gauges cannot, enabling checks of sleeves, housings and stepped bores. The compact set format of 21 pieces covers the range 8.00–9.00 mm in close increments, allowing stepwise selection for precise sizing. The clear grading supports efficient workflows in assembly, inspection benches and tool preset stations, reducing handling time and the likelihood of measurement errors. Organisation and transport made simple The set is supplied in a protective case suitable for transport and safe storage, keeping pins organised and preventing accidental damage. A compact case is particularly useful for mobile inspection or shared inspection points across production lines, helping to preserve accuracy by avoiding mixed or damaged gauges. The complete set is ready for immediate use on the shop floor or in the inspection room. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine gauge pin set M318.828 — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for specific bore-tolerance tasks Technical data Article number: M318.828 GTIN: 4054469182001 Manufacturer: Metav IndustryLine Facts Diameter range: 8.00–9.00 mm Increment / step: 0.05 mm Length: 70 mm Pieces per set: 21 Weight: 1.32 kg Special features Material: special steel Supplied in protective transport case Application category: inspection gauges FAQ What sizes are included in the set? The gauge pin set M318.828 (Metav IndustryLine) contains pins covering the diameter range 8.00–9.00 mm in 0.05 mm increments. Are the pins suitable for use on hardened components? Pins in the M318.828 set are made of special steel and are intended for standard verification tasks; for repeated use against very hard surfaces, please consider application-specific wear assessments. Can this set be used for deep bore checks? Yes, the 70 mm pin length is designed to reach deeper bores and sleeves where shorter pins would be insufficient. Is the set supplied ready for transport and storage? The complete 21-piece set is supplied in a protective case for transport and organised storage, protecting the pins from damage. Which applications suit this pin set best? The set is optimised for routine bore inspection, go/no-go verification and quick size checking in machine shops, toolrooms and quality-control stations; refer to M318.828 (Metav IndustryLine) for workshop use Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 mm Ceramic Measurement Ball (Si3N4) 0.003 mm Accuracy, HV1400–1700 Hardness - Metav IndustryLine
Benefit from the combination of Si3N4 ceramic construction, sub‑millimetre consistency and exceptional surface quality to improve gauge repeatability and reduce inspection variation. Choose this spherical reference for stable contact geometry and reliable long‑term performance; order directly via Metav Werkzeuge or consult our metrology advisors for application support. Ceramic measuring ball (Si3N4) M318.439 — 9 mm, 0.003 mm accuracy | Metav IndustryLine The Ceramic measuring ball (Si3N4) serves as a compact, high‑stability reference sphere for gauges and dimensional inspection in metrology and toolmaking environments. Si3N4 ceramic, high hardness HV1400–1700 9 mm diameter with 0.003 mm accuracy Ultra‑smooth surface Ra 0.00001 Precision that shortens inspection cycles Precision inspection depends on stable, repeatable contact points; the Ceramic measuring ball (Si3N4) delivers a defined spherical reference with 0.003 mm accuracy and a diameter of 9 mm, enabling predictable probe responses and reduced measurement scatter. The low surface roughness and tight diameter tolerance contribute to consistent seating and minimal micro‑movement during gauge checks, which shortens set‑up times and improves throughput in batch inspection. Where interchangeable fixtures and quick verification are required, a compact reference sphere simplifies alignment and reduces the need for repeated compensation. Durability and dimensional stability for repeated use Manufactured from Si3N4, the sphere combines high hardness with thermal and wear resistance, giving long service life in routine inspection tasks. The HV1400–1700 hardness rating and ultra‑smooth surface support sustained contact with probes and tactile instruments while limiting abrasive wear. The modest mass and compact 9 mm form factor make the sphere easy to integrate into existing gauge blocks, detectors or master sets without adding undue inertia; this aids handling and reduces the risk of measurement error caused by movement or deformation. Straightforward integration into inspection workflows Labelling and identification (SKU M318.439, GTIN provided) simplify inventory control and traceability for quality systems. The combination of material properties and micrometric accuracy makes the sphere suitable for use as a master reference in comparative checks, fixture calibration and fixture‑to‑CMM transfers. Its compatibility with standard metrology accessories means it can be mounted or located in typical gauge interfaces without bespoke adaptors, so measuring stations can be standardised across production lines. The clear numeric specifications enable a rational decision on suitability for specific tolerance stacks or verification protocols. Contact Metav Werkzeuge today to discuss the suitability of M318.439 for gauge references or precision fixtures and to request stock and technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M318.439 GTIN: 4054469184395 Material: Ceramic (Si3N4) Diameter: 9 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 Surface roughness Ra: 0.00001 Hardness: HV1400–1700 Weight: 0.08 kg Facts Diameter: 9 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 Surface roughness Ra: 0.00001 Weight: 0.08 kg Hardness: HV1400–1700 Special features Material: Si3N4 ceramic Application: gauge and dimensional inspection Category: gauges (Lehren) Identification: SKU M318.439, GTIN 4054469184395 FAQ What is the primary application for this ceramic measuring sphere? The Ceramic measuring ball (Si3N4) M318.439 from Metav IndustryLine is intended as a reference sphere for gauges, fixture checks and dimensional inspections where a defined contact geometry improves repeatability. How precise is the sphere for reference measurements? The sphere offers an accuracy of 0.003 mm with a diameter of 9 mm and a diameter tolerance of 0.00008, providing a stable reference for comparative and fixture verification tasks. Is the ceramic material suitable for long‑term use under regular contact? Yes. Si3N4 ceramic with a hardness of HV1400–1700 and an ultra‑smooth surface finish minimises wear and supports sustained, repeatable contacts in routine inspection. Can the sphere be used directly in standard gauge fixtures? The compact 9 mm size and defined geometry allow straightforward placement in common gauge and fixture arrangements, easing integration into existing inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 mm Gauge Ball Pair, Hardened Chrome Steel, 0.003 mm Accuracy, Tolerance 0.00008 mm - Metav IndustryLine
Take advantage of high repeatability and wear resistance combined with a compact 9 mm form factor — ideal for reference, alignment and probing tasks in precision metrology. Benefit from 0.003 mm accuracy and hardened chrome‑steel construction for long service life; order directly via Metav Werkzeuge or contact the consultants for application advice. Gauge ball pair M318.419 — hardened chrome‑steel, 9 mm, 0.003 mm accuracy (Metav IndustryLine) The Gauge ball pair M318.419 is a compact 9 mm hardened chrome‑steel set designed as a high‑precision reference for gauging, alignment and measurement fixtures in inspection and production environments. 9 mm hardened chrome‑steel balls Precision tolerance 0.00008 mm Accuracy 0.003 mm Supplied as a set of two Reliable reference for high-precision measurement The pair provides a stable, reproducible reference surface for coordinate measurement machines, tactile probing systems and optical comparators. With a declared accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, the spheres enable repeatable contact points that reduce uncertainty in positional checks. The extremely fine surface finish (0.00001 as supplied) minimises local measurement artefacts and supports consistent probing behaviour during cyclic inspection routines. Durable material and dimensional stability Manufactured from hardened chrome steel and rated at >HRC 62, the balls resist wear and maintain geometry under frequent contact. This hardness level ensures dimensional stability where repetitive probing or preloaded contact occurs, extending service intervals and lowering replacement frequency. Their compact 9 mm diameter combines rigidity with small footprint, making the spheres suitable for confined fixtures and fine‑feature reference duties without compromising stiffness. Simple integration into metrology workflows Delivered as a set of two, the pair can be used for comparative checks, alignment between two datum points or as matched references in bespoke fixtures. The modest mass contributes to easy handling while preserving thermal behaviour suitable for shopfloor and laboratory conditions. Traceability is supported by the product identifiers and packaging, facilitating inventory and quality records for inspection processes — a practical choice when repeatability and process reliability are priorities. For precise alignment and reliable reference points, contact Metav Werkzeuge to discuss how the Metav IndustryLine gauge ball pair M318.419 can be integrated into existing inspection procedures — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice. Technical data Article number: M318.419 GTIN: 4054469184074 Brand: Metav IndustryLine Facts Diameter: 9 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Surface roughness: 0.00001 Hardness: >HRC 62 Weight: 0.05 kg Special features Material: hardened chrome steel Supplied as a set: 2 pieces Intended use: reference/gauge applications FAQ What diameter and accuracy do these gauge balls offer? The gauge ball pair M318.419 features a 9 mm diameter and a declared accuracy of 0.003 mm for high‑precision reference tasks. Can these spheres be used with CMMs and tactile probes? Yes, the hardened chrome‑steel spheres are suitable as reference points for coordinate measurement machines and tactile probing systems due to their tight tolerance and stable surface finish. How durable are the measuring balls for repetitive contact use? With a hardness above HRC 62 and hardened chrome‑steel construction, the spheres resist wear and maintain dimensional stability under frequent probing. Is the product supplied as individual balls or a matched set? The item is supplied as a matched set of two spheres, enabling comparative checks and paired reference mounting. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 mm Gauge Pin Single, ±0.001 mm Accuracy, 50 mm Length, Workshop Version - Metav IndustryLine
The 9.00 mm single pin gauge delivers a highly stable reference with an exceptionally fine ±0.001 mm tolerance and a 50 mm overall length, making it suitable for precise setting and inspection tasks in confined assemblies. The workshop-grade construction and special-steel body ensure long service life and consistent repeatability; order directly via Metav Werkzeuge or consult the Metav team for application advice. Pin gauge (single) 9.00 mm, ±0.001 mm – 50 mm length (Metav IndustryLine) The Pin gauge, single 9.00 mm is a compact, high-precision reference pin designed for inspection, go/no-go checks and dimensional setting tasks in workshop metrology. ±0.001 mm tolerance for reference accuracy Nominal diameter 9.00 mm 50 mm hardened special steel body Workshop-grade finish for daily use Engineered for repeatable reference measurements The instrument is specified with a ±0.001 mm tolerance, which positions it as a precision reference for fine inspection tasks where minimal uncertainty is required. This level of deviation corresponds to sub-micron alignment expectations in many production checks and calibration routines; the tight tolerance reduces adjustment iterations and supports faster verification cycles. The compact 9.00 mm nominal diameter combined with a 50 mm overall length provides a stable contact feature that resists lateral play during insertion, improving repeatability when used as a reference pin or setting master. Built for dependable use in workshop environments Constructed from special steel and finished for workshop use, the device stands up to frequent handling and routine measurement work. The workshop specification indicates enhanced surface quality and dimensional stability under practical conditions, supporting a consistent reference point over repeated cycles. The robust construction translates directly into lower rework rates and fewer measurement uncertainties during setup, which supports efficient machining and quality-control workflows without compromising on precision. Measurement context and typical applications This single pin is intended for end-measurement roles such as reference checking of bores, alignment of gauges, and insertion verification in assemblies. In these contexts the gauge provides a precise datum for comparative measurements and functional go/no-go testing. Its attributes make it suitable for use in small-part inspection, tool-setting processes and precision jigs where space is limited but measurement fidelity remains critical. As a workshop-grade reference pin it complements inspection equipment and can be integrated into daily quality checks to uphold process reliability. Choose the Metav IndustryLine single 9.00 mm pin gauge for a compact, traceable reference solution; contact Metav Werkzeuge in Emmerich for tailored advice and procurement assistance. Technical data Article number: M323.900 GTIN: 4061905062049 Item: Pin gauge, single, 9.00 mm, ±0.001 mm, 50 mm length Facts Diameter: 9.00 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Material: special steel Workshop version Accuracy class: ±0.001 mm ECLASS: 21170231 FAQ What is the declared tolerance of this pin gauge? The pin gauge is specified with a ±0.001 mm tolerance, providing a fine reference for precision inspection and setting tasks. Which tasks are suited to this 9.00 mm pin gauge? The gauge is intended for end-measurements, bore checks, insertion verification and tool-setting where a compact, stable reference is required. What material is used for the gauge and what does that mean for durability? Manufactured from special steel, the pin gauge offers workshop-grade resistance to wear and maintains dimensional stability under normal handling and inspection cycles. Is this pin gauge suitable for use in confined assemblies? Yes, the compact nominal diameter and 50 mm length make it suitable for confined spaces where a precise reference pin is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 mm Limit Plug Gauge DIN 2245 H7 Hardened Gauge Steel - Metav IndustryLine
Data inconsistency detected: the product record contains conflicting information about condition and mass (both good and scrap indicators are set; weight appears as 0.04 kg and 0.1 kg). This discrepancy makes it impossible to determine the accurate status of the product, which is essential for generating a reliable, production-ready product description. Without resolving these inconsistencies, the data cannot be used effectively for further processing or specification purposes. Please ensure that the product data is thoroughly reviewed, corrected, and resubmitted to enable the generation of a complete and accurate specification. Accurate data is crucial for maintaining quality and consistency in production records.
9 mm Limit Plug Gauge Wear Measurement Side, Hardened Steel, DIN 7162 - Filetta
Take advantage of precise pass/fail inspection, rugged hardened steel construction and clear compliance with DIN 7162 for reliable throughput in production control; order the limit gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Limit gauge pin G7 — 9 mm, hardened steel, DIN 7162 Limit gauge pin G7 for rapid go/no-go verification in machining and inspection environments, designed to simplify batch acceptance and reject decisions. Hardened steel construction DIN 7162 compliant 9 mm nominal diameter Wear allowance on the go side Fast, objective pass/fail inspection for production lines A compact inspection tool engineered for decisive checks, the limit gauge pin provides a straightforward go/no-go result that removes ambiguity from routine quality control. Manufactured from hardened steel and produced to DIN 7162 tolerances, the pin gives repeatable contact geometry and low variation between checks. The simple plug-style design shortens inspection cycles and reduces handling time, helping to maintain throughput without sacrificing measurement integrity. Robust design that keeps maintenance intervals long The combination of hardened material and a defined wear allowance on the go side minimises in-service degradation and extends service life. The wear allowance compensates for gradual material loss where contact is most frequent, so the pin continues to represent the required acceptance limit for longer. As a result, tool replacement intervals are extended and unplanned downtime for gauge renewals is reduced, supporting smoother production schedules and lower indirect costs. Practical compatibility and clear traceability for inspection routines Suitable for quick hole and bore acceptance tests across general machining, assembly and incoming inspection, this plug gauge integrates easily into standard inspection kits. The nominal 9 mm size is instantly recognisable and compatible with common fixture layouts; identification is simplified by the SKU MS911.171 and clear marking. For workshop procurement and quality documentation, the robust construction and standardised dimensioning deliver dependable evidence for conformity assessments and sampling plans. Contact Metav Werkzeuge for Filetta G7 limit gauge pin availability, application guidance and order placement — expert advice from our Emmerich team ensures the correct plug gauge for each inspection task Technical Data Article number: MS911.171 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Facts Nominal diameter: 9 mm Type: limit gauge pin (go/no-go principle) SKU: MS911.171 Special features Wear allowance on the go side (Abnutzungsaufmaß der Gutseite) Suitable for plug-type acceptance tests Compact, transfer-friendly design FAQ What nominal size does this plug gauge represent? The Filetta limit gauge pin is specified with a nominal diameter of 9 mm (SKU MS911.171), suitable for standard hole acceptance checks. Which material and standard apply to this gauge? This plug gauge is made from hardened steel and manufactured to DIN 7162, ensuring consistent contact geometry and conformity to recognised metrology standards. How does the wear allowance affect service life? The wear allowance on the go side prolongs usable life by compensating for gradual wear at the contact surface, so the gauge retains its acceptance function longer between replacements. Is the pin suitable for production inspection routines? Yes; the plug gauge is intended for rapid go/no-go verification in machining, assembly and incoming inspection, offering clear pass/fail decisions and easy integration into inspection kits. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
9 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Take advantage of a compact, standards‑compliant checking solution: a hardened‑steel limit plug gauge that meets DIN 7162 and includes a wear allowance on the go side for extended service life; order via Metav Werkzeuge or consult their specialists for application advice. Limit plug gauges MS911.213 — hardened steel, DIN 7162 A limit plug gauge MS911.213 for fast go/no‑go checking and acceptance testing of 9 mm bores in production and inspection environments Hardened steel construction DIN 7162 compliant Wear allowance on go side Fast, reliable acceptance checks on the shop floor For routine inspection and first‑piece approval, a compact go/no‑go gauge provides immediate, objective results. The hardened body resists abrasion so tolerance boundaries remain stable over repeated cycles, while the simple two‑position concept reduces operator decisions to a single pass/fail action. This lowers cycle time in quality control and removes ambiguity from visual measurements, making process control faster and more consistent. Durability that reduces downtime and recalibration cycles The hardened steel used in this design is selected to maintain dimensions under mechanical stress and frequent handling. The integrated wear allowance on the go side extends the usable life before refurbishment is required, which reduces the frequency of replacements and preserves measurement reliability between maintenance intervals. For high‑turnover inspection points, this translates into fewer interruptions and lower total cost of ownership. Standards-based traceability for audit and production control Manufactured to DIN 7162, the gauge aligns with widely accepted metrology practice for limit gauges, simplifying documentation and acceptance during audits. Conformity to the standard means the tool can be relied upon for contractual checks and in‑line sampling plans where repeatable limits are essential. The compact format and clear definition of the checking faces support consistent results across shifts and operators. Practical advantages in inspection and fixture testing The small diameter of 9 mm makes the device particularly suitable for plug checks in small‑bore components, jigs and fixtures used in precision assembly. As a purpose‑designed gauge pin, it fits into production routines without the need for elaborate setup, and its robust construction withstands the handling typical in workshop and toolroom environments. Use in go/no‑go sequences or as a quick reference tool helps shorten inspection throughput while keeping decision criteria unambiguous. For production‑grade bore control, request the Filetta limit plug gauge MS911.213 through Metav Werkzeuge — their advisors will confirm suitability for the intended application and arrange supply details Technical Data Article number: MS911.213 Product: Limit plug gauges Brand: Filetta Material: hardened steel Standard: DIN 7162 Size / diameter: 9 mm Special note: wear allowance on go side Facts SKU: MS911.213 Category: gauges / gauge pins Image available: yes Special features Designed for go/no‑go checking Intended for production and inspection use Wear‑compensated go side Robust hardened construction FAQ What is the primary purpose of this gauge? The limit plug gauge MS911.213 is intended for go/no‑go checking and quick acceptance testing of 9 mm bores in production and inspection processes. Which material is used for the gauge? This gauge is made from hardened steel to provide abrasion resistance and long service life under repetitive use. Is the gauge standardised? Yes, the tool is manufactured in accordance with DIN 7162, ensuring consistent limits and traceable use in quality systems. How does the wear allowance affect usage? The wear allowance on the go side prolongs the period during which the gauge reliably represents the intended limit, reducing replacement frequency and maintaining inspection integrity. Can this gauge be used in fixture and jig checks? The compact 9 mm diameter and robust design make it suitable for plug checks in fixtures, jigs and small‑bore components during assembly and testing. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
9 mm Setting Ring Form C Hardened Gauge Steel DIN 2250, JS3 - Metav IndustryLine
Combine the hardened gauge-steel construction, DIN 2250 conformity, and a compact 9 mm diameter for dependable setting and repeatable inspection results; order the setting ring directly via Metav Werkzeuge or consult their specialists for application advice. M313.009 Setting ring 9 mm (Form C) — hardened gauge steel, DIN 2250 The M313.009 setting ring is a hardened, lapped gauge ring designed for precise sizing and verification tasks in workshop and inspection environments. Hardened and lapped gauge steel finish Conforms to DIN 2250 and DIN 286 Compact 9 mm diameter for fine gauges Precision that speeds up inspection cycles The compact reference ring provides a stable reference diameter that reduces set‑up time and measurement variation. Manufactured to DIN 2250 with tolerance class JS 3, the ring acts as a reproducible standard for plug gauges, go/no‑go checks and comparator routines. The controlled geometry and lapped finish limit wear and preserve the reference surface, which contributes to fewer adjustments on the production line and a lower risk of rework. In practice, this translates to a more efficient quality workflow and clearer pass/fail criteria. Robust construction for long service life Made from hardened gauge steel and finished by lapping, the ring resists abrasive wear and maintains its calibre under repeated use. The Form C profile is particularly suited to setting applications where edge definition and concentricity matter; the result is stable measurements over many cycles. As a durable workshop reference, the component reduces the frequency of replacements and associated downtime, delivering a tangible efficiency gain for maintenance and inspection teams. Simple integration into metrology routines With a 9 mm nominal diameter the ring fits readily into common gauge sets and inspection fixtures used in precision engineering and toolmaking. Traceable identification via SKU and GTIN supports inventory and calibration records, while the straightforward geometry eases handling during routine checks. For customers seeking to harmonise their measuring equipment, the ring offers a compact, standardised solution that complements existing plug gauge inventories and bench fixtures without adding complexity. Contact Metav Werkzeuge today for application guidance and to secure the M313.009 setting ring with reliable dispatch from Emmerich. Technical data Article number: M313.009 GTIN: 4054469120478 ECLASS: 21170104 Customs tariff number: 90173000 Designation: Setting ring 9 mm (Form C) Facts Diameter: 9 mm Tolerance class: JS 3 Standards: DIN 2250; DIN 286 Special features Material: hardened and lapped gauge steel Finish: lapped Form: Form C Application: setting and inspection of plug gauges and go/no‑go checks FAQ What is the primary purpose of this setting ring? The M313.009 setting ring is intended as a stable reference for sizing, setting and verifying plug gauges and similar inspection fixtures in workshop and quality‑control environments. Which standards and tolerance class apply to this ring? The ring is manufactured to DIN 2250 and DIN 286 and is specified in tolerance class JS 3 for consistent reference performance. What material and finish ensure longevity? Constructed from hardened gauge steel with a lapped finish, the ring offers high wear resistance and a preserved reference surface for repeated use. Is this ring suitable for precision inspection work? Yes; the combination of hardened material, lapped surface and JS 3 tolerance makes it suitable as a workshop reference where reproducibility and clear acceptance criteria are required. How is the component identified for inventory and traceability? The setting ring is identified by article number M313.009 and GTIN 4054469120478 for seamless integration into inventory and calibration records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9,54mm Prüfstift, Länge 50mm, ±0,001mm, Werkstatt-Ausführung - Metav IndustryLine
Der hohe Präzisionsgrad ±0,001 mm, die Länge 50 mm und die robuste Werkstatt‑Ausführung bieten reproduzierbare Endmaße für feinmechanische Fertigungen; Bestellen Sie den Prüfstift direkt über Metav Werkzeuge oder kontaktieren Sie unsere Beratung bei Bedarf. Prüfstift, einzeln, 9,54mm, +/- 0.001 mm Länge 50 mm – Präzisions‑Prüfstift von Metav IndustryLine Der Prüfstift, einzeln, 9,54mm, +/- 0.001 mm Länge 50 mm ist ein kompaktes Endmaß für präzise Kontrollmessungen in Werkstatt und Fertigung und eignet sich besonders für feinmechanische Bauteile. Extrem präzise Toleranz ±0,001 mm Robuste Ausführung aus Spezial‑Stahl Länge 50 mm für Endmaß‑Prüfungen Werkstatt‑Ausführung für den Dauereinsatz Lieferung in stabilem Transportkasten Präzision und Material für reproduzierbare Endmaße Der Prüfstift zeichnet sich durch eine Toleranz von ±0,001 mm aus, wodurch er anspruchsvolle Messaufgaben in der Fertigungs‑ und Prüfprozessen zuverlässig erfüllt. Das verwendete Spezial‑Stahl sorgt für hohe Verschleißfestigkeit und Maßhaltigkeit auch bei häufiger Nutzung. Durch die kompakte Länge 50 mm und das geringe Gewicht 0,032 kg bleibt das Handhabungsgewicht niedrig, was präzise Lagerung des Prüfstifts und reproduzierbare Ergebnisse bei wiederholten Kontrollen erleichtert. Die Kombination aus Materialwahl und Fertigungsgenauigkeit minimiert Einflüsse durch Umgebungsbedingungen auf das Messergebnis. Einsatzgebiete und Anwendernutzen in der Werkstatt Dieses Messwerkzeug ist für die Anwendung in der Feinmechanik, im Maschinenbau und in der Qualitätskontrolle konzipiert. Dank seiner kompakten Abmessungen eignet es sich ideal für Prüfplätze, Lehren sowie Endmaßkontrollen kleiner Bauteile und Spannmittel. Die Werkstatt‑Ausführung macht den Prüfstift robust gegenüber täglichem Gebrauch, wodurch sich die Nutzungsdauer verlängert und Stillstandzeiten wegen Ersatzbeschaffung reduziert werden. Anwender erhalten so ein praxisorientiertes Werkzeug für wiederkehrende Prüfzyklen. Messcharakteristik und Einordnung Mit einem Messbereich von 9,54 mm ordnet sich der Prüfstift in den Mikro‑Bereich für feinmechanische Arbeiten ein; dieses Format bietet auf kleinem Raum hohe Steifigkeit und geringe Verwölbung. Die spezifizierte Genauigkeit bewegt das Produkt in einen Bereich, der deutlich über typischen industriellen Mechanik‑Standards liegt und sich für präzise Endmaß‑Kontrollen eignet. Für Anwender, die reproduzierbare Messergebnisse erwarten, ist die Kombination aus kompaktem Format und hoher Genauigkeit ein entscheidender Vorteil. Verpackung, Lieferung und Pflegehinweise Der Prüfstift wird sicher verpackt geliefert; die Lieferung erfolgt in einem stabilen Transportkasten, der den Schutz beim Versand gewährleistet und die sichere Aufbewahrung bis zum Einsatz ermöglicht. Zur Erhaltung der Präzision empfiehlt sich eine sachgerechte Lagerung in trockener Umgebung sowie gelegentliche Reinigung mit geeignetem Lösemittel und leichter Ölung der Oberfläche. Die robuste Bauweise reduziert den Pflegeaufwand und unterstützt langfristige Einsatzbereitschaft. Empfehlung: Setzen Sie auf die Präzision von Metav IndustryLine und beziehen Sie den Prüfstift direkt über Metav Werkzeuge; bei Fragen hilft die technische Beratung unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 weiter. Produktmerkmale Artikelnummer: M323.954 Marke: Metav IndustryLine Bezeichnung: Prüfstift, einzeln, 9,54mm, +/- 0.001 mm Länge 50 mm GTIN: 4061905065897 Material: Spezial-Stahl Gewicht: 0.032 kg Fakten Länge: 50 mm Messbereich: 9.54 mm Genauigkeit: ±0,001 mm Besonderheiten Werkstatt-Ausführung Lieferung in Transportkasten EClass: 21170231 FAQ Wie genau ist der Prüfstift und für welche Prüfungen eignet er sich? Der Prüfstift von Metav IndustryLine (Prüfstift, einzeln, 9,54mm, +/- 0.001 mm Länge 50 mm, SKU M323.954) bietet eine Genauigkeit von ±0,001 mm und eignet sich speziell für Endmaß‑Kontrollen und präzise Prüfaufgaben in der Feinmechanik und Qualitätskontrolle. In welchem Bereich liegt der Messumfang dieses Prüfstifts? Der Messumfang beträgt 9,54 mm; damit gehört das Produkt in den Mikro‑Bereich für kompakte, hochpräzise Messaufgaben und ist besonders geeignet für kleine Bauteile und präzise Prüflehren. Aus welchem Material besteht der Prüfstift und welche Vorteile hat das? Der Prüfstift besteht aus Spezial‑Stahl, was eine hohe Verschleißfestigkeit und Maßstabilität gewährleistet; das Material unterstützt konstante Messergebnisse auch bei häufiger Benutzung in der Werkstatt. Wird der Prüfstift kalibriert geliefert oder ist eine Kalibrierung erforderlich? Für dieses Produkt liegt keine Angabe zu einer speziellen Kalibrierung nach ISO 17025 vor; daher erfolgt die Lieferung standardmäßig ohne ISO‑17025‑Kalibrierschein. Bei Bedarf kann die Kalibrierung über die technische Beratung von Metav Werkzeuge geklärt werden. Wie wird der Prüfstift geliefert und ist eine sichere Aufbewahrung vorgesehen? Der Prüfstift wird in einem stabilen Transportkasten geliefert, der Schutz beim Versand bietet und eine sichere Aufbewahrung ermöglicht; die robuste Verpackung reduziert Transportschäden und erleichtert das Handling in der Werkstatt. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9-10mm Ceramic Gauge Pin Set 101 Pieces 0.01mm Steps, Stainless ZrO2, 50mm Length, Plastic Case - Metav IndustryLine
Take advantage of the set's combination of zirconia ceramic durability, workshop-ready handling and sub‑micron accuracy for repeatable fit checks; order via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge pin set, 101-piece — 9.00–10.00 mm, 0.01 mm increments (Metav IndustryLine) The Ceramic gauge pin set, 101-piece 9.00–10.00 mm (0.01 mm) is a workshop-grade collection of precision plugs for checking hole sizes, fits and clearances in production and inspection tasks. Zirconia ceramic, highly wear-resistant Workshop version with 50 mm length Accuracy better than ±0.0015 mm Delivered in plastic case with pin holder Reliable measurement where wear and magnetism matter Made from zirconia ceramic, the set is inherently antimagnetic and wear-resistant, which reduces drift in repeated checks and minimises contamination risk in sensitive assemblies. The material's high surface hardness (HV 1250) maintains diameter integrity under routine use, so each gauge retains its nominal size longer than equivalent steel pins. This leads to fewer re-measurements and steadier throughput in quality control, a clear efficiency advantage for production lines and bench‑level inspection. Workshop design for fast, consistent checks The workshop-grade layout—101 items in 0.01 mm increments across 9.00–10.00 mm—supports quick selection and serial checking without time‑consuming adjustments. Each pin measures 50 mm in working length and is supplied in a compact plastic case with an integrated pin holder, keeping the set organised and protecting tolerances during storage. These features reduce handling time and the risk of accidental damage, enabling technicians to maintain consistent cycle times on repetitive tasks. Classification and typical applications in the micro range With a measurement span that sits between 9.00 and 10.00 mm, the set falls into the micro category for precision gauges (suitable for very compact fits and fine mechanical parts). It is therefore particularly useful for small‑bore inspection in watchmaking, instrument manufacture and fine mechanical assemblies where space is limited but high repeatability is required. The supplied accuracy specification (< ±0.0015 mm) makes the set appropriate for strict fit verifications and calibration comparisons on sub‑millimetre features. For dependable, low‑maintenance fit checking choose the Metav IndustryLine ceramic gauge pin set and contact Metav Werkzeuge in Emmerich for tailored application support: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M318.599 Manufacturer: Metav IndustryLine Set size: 101 pieces Diameter range: 9.00–10.00 mm Increment: 0.01 mm Length: 50 mm Material: zirconia ceramic Hardness: HV 1250 Accuracy: < ±0.0015 mm Delivery: plastic case with pin holder Numbers / Core technical data Diameter range: 9.00–10.00 mm Increment: 0.01 mm Length: 50 mm Hardness: HV 1250 Accuracy: < ±0.0015 mm Set count: 101 pieces Special features / Versions Zirconia ceramic construction Antimagnetic properties Wear-resistant surface Workshop-grade execution Supplied in plastic case Includes pin holder FAQ What material are the pins made from and why is that useful? The pins are made from zirconia ceramic; this provides high wear resistance and antimagnetic behaviour, helping the Ceramic gauge pin set, 101-piece (M318.599) retain accuracy in repeated checks. What is the stated accuracy and how does it affect inspections? The set specifies an accuracy of < ±0.0015 mm, which supports precise fit verification and reduces the need for repeat measurements during routine quality control. For which applications is the 9.00–10.00 mm range intended? The 9.00–10.00 mm span suits micro‑range fit checks in fine mechanics, instrument making and other small‑bore inspections where compact components require consistent, repeatable gauging. How are the pins supplied and how does that aid workshop use? The 101-piece set is supplied in a plastic case with a pin holder, keeping each plug organised and protected to simplify selection and minimise handling time on the shop floor. Can these pins be used in magnetic environments or on magnetic components? Yes; the antimagnetic nature of the zirconia ceramic pins avoids magnetic interference, making them suitable for inspection tasks near magnetic assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.01-10 mm Gauge Pin Set 100 Pieces 0.01 mm Increment Supplied in Case - Metav IndustryLine
Take advantage of a finely graduated set that combines reliable diameter verification with workshop-grade robustness; the precise 0.01 mm steps and a typical tolerance of ±0.002 mm support repeatable decisions on the shop floor. Order the kit directly via Metav Werkzeuge or ask Metav's consultants for specification advice and availability. Gauge pin set M318.559 — 100-piece, 9.01–10.00 mm (0.01 mm steps) by Metav IndustryLine The Gauge pin set M318.559 is designed for precise diameter checking and fit verification across the 9.01–10.00 mm band, suitable for inspection, tool setting and acceptance testing in production environments 0.01 mm step for fine incremental gauging High-grade special steel construction Measurement range 9.01–10.00 mm Supplied in protective case for transport Consistent precision for inspection and quality control The gauge pins in this kit span the 9.01–10.00 mm range in 0.01 mm increments, enabling fine gradation when verifying bore sizes or checking shaft diameters. With a measured tolerance on the order of ±0.002 mm, the set supports reproducible go/no-go and transition-fit checks that reduce subjective judgement in routine inspection. Made from special steel, the pins resist wear under repeated contact and retain dimensional stability, which is crucial when used as a reference during first-article inspection or in-process checks. Built for workshop use and safe transport Organised storage and safe handling reduce downtime: the kit is delivered in a secure, organised box and has a collective weight of 4.5 kg, which keeps the set portable while protecting individual gauges. Each pin has a length of 50 mm, optimised for stable support in seating and insertion tasks without excessive overhang. The 100-piece composition provides dense resolution across the interval so that technicians can reach the exact diameter step quickly without resorting to filing or shimming, improving throughput at the measuring bench. Speeding up inspection and reducing downtime Using a finely stepped set like this accelerates decision-making in production inspections: installers and inspectors find the matching pin rapidly, avoiding iterative caliper measurements and reducing cycle time. The kit is particularly useful for assembly checking, fixture set-up and routine acceptance testing where fast, objective diameter verification prevents rework. Backed by Metav IndustryLine's distribution and quality control, the set supports reliable supply and consistent lot quality for small-batch and continuous operations alike. For tailored specification support or to secure supply from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for availability and delivery guidance — Metav Werkzeuge can advise on application fit and dispatch the required items directly Technical data Article number: M318.559 GTIN: 4054469129426 HS code: 90173000 Manufacturer: Metav IndustryLine Dimensions & precision Measurement range: 9.01–10.00 mm Graduation: 0.01 mm Accuracy: ±0.002 mm Pieces per set: 100 Individual pin length: 50 mm Weight (total): 4.5 kg Materials & features Material: Special steel Protective transport case included Category: Gauge pins / inspection gauges Intended use: Diameter verification, fit checks, fixture set-up FAQ What is the intended use of this gauge pin set? The gauge pin set M318.559 is intended for diameter verification, go/no-go checks and fixture setting where incremental diameter selection between 9.01 mm and 10.00 mm is required. How fine are the increments and what tolerance can be expected? Increments are 0.01 mm and the typical tolerance associated with this kit is ±0.002 mm, giving fine-grain control for close-tolerance inspections. Which materials are the pins suitable for measuring? The pins are made from special steel and are used to measure diameters of shafts and bores made from common workshop materials; they are a measuring standard rather than a cutting tool. Is the kit suitable for workshop environments with frequent handling? Yes. The set is supplied in a protective case and the pins are designed for repeated insertion and extraction; organised storage reduces handling time and wear. Can this set replace micrometre checks for small production batches? For quick verification and fit decisions the set provides faster throughput; where traceable absolute measurements are required, complementing pins with calibrated micrometres is recommended. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.01-10.0 mm Precision Gauge Pin Set With Pin Holder 0.01 mm Graduation In Plastic Case - Metav IndustryLine
This gauge-pin set delivers traceable, workshop-ready sizing across the 9.01–10.00 mm range while combining fine 0.01 mm increments with a declared accuracy of 0.004 mm, enabling consistent pass/fail checks and high-repeatability gauging; order directly via Metav Werkzeuge or speak to our consultants for specification support. Gauge Pin Set M318.579 — 101-piece, 9.01–10.00 mm, 0.01 mm graduations (Metav IndustryLine) A Metav IndustryLine gauge pin set designed for precision diameter verification and toolsetting in inspection, toolroom and production environments. 101-piece hardened gauge pin set Diameter range 9.01–10.00 mm per 0.01 mm step Graduation 0.01 mm for fine adjustment Holder included for organised handling Consistent dimensional control through measurable precision The set is engineered to support reliable size verification and incremental adjustment tasks with a declared accuracy of 0.004 mm, which keeps tolerance checks tight and reduces rework. Using pins in 0.01 mm steps permits fine interpolation between standard nominal sizes, so set-up and verification processes become more predictable. For users in quality assurance and production metrology, this translates into fewer rejected parts and steadier process capability. Practical set composition that speeds inspection and set-up Supplied as a comprehensive kit, the tools cover diameters from 9.01–10.00 mm in 0.01 mm increments and each pin has a usable length of 50 mm, making them suitable for a wide range of holes and bores. The pins are manufactured from special steel, offering a balance of surface hardness and corrosion resistance that supports repeated use. The inclusion of a dedicated holder assists orderly storage and quick selection during serial inspection or machine set-up, improving throughput and operator ergonomics. Designed for integration into workshop workflows The modular nature of this set supports both bench inspection and on‑machine referencing: the compact, graduated increments aid precise alignment of fixtures and cutting tools, while the robust construction stands up to everyday handling. Backed by Metav’s long-standing supply chain and quality assurance ethos, the kit is aimed at shops and maintenance departments seeking dependable measuring aids that simplify process control and minimise downtime. Contact Metav Werkzeuge for detailed technical guidance on Metav IndustryLine gauge pin sets and to discuss how this precision kit can be integrated into existing inspection routines; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M318.579 GTIN: 4054469168333 Manufacturer: Metav IndustryLine Facts Diameter range: 9.01–10.00 mm Graduation: 0.01 mm Nominal accuracy: 0.004 mm Length (usable): 50 mm Weight (set): 4.17 kg Special features Material: Special steel Set: 101 pieces Inclusive: Pin holder FAQ What diameter range does the set cover? The set covers diameters from 9.01 mm to 10.00 mm in 0.01 mm increments, allowing detailed sizing within that band. Is the accuracy suitable for workshop quality control? Yes, the set is specified with a nominal accuracy of 0.004 mm, which supports tight tolerance checks in routine inspection tasks. What material are the pins made from? The pins are manufactured from special steel designed for repeated use and good dimensional stability. How is the set organised for use during inspection? The kit includes a dedicated pin holder to keep pins organised and to speed selection during measurement and setting operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.01mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Precision end-dimension control combined with workshop-grade durability: the gauge pin delivers Ø 9.01 mm nominal size with ±0.001 mm accuracy over a 50 mm length, enabling consistent final-dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed Gauge pin M323.901 — 9.01 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The gauge pin M323.901 is a precision measurement pin designed for final-dimension inspection in industrial metrology and workshop environments, offering a compact reference for verification of bore and end measurements High-precision Ø 9.01 mm ±0.001 mm Special steel for workshop use 50 mm length for repeatable contact Securing final dimensions with micrometre-level accuracy The core advantage lies in the exceptionally tight tolerance of ±0.001 mm (1 µm), which positions this pin as a practical reference for critical end-dimension tasks. Such precision reduces measurement ambiguity during acceptance checks and process control, providing a reliable physical standard for comparative inspections. The nominal Ø 9.01 mm is suitable where small-diameter bores and end fits must be verified with minimal uncertainty, and the specified tolerance supports traceable quality routines that prioritise reproducibility over multiple cycles. Durable workshop execution for everyday metrology Built as a workshop version, the pin combines precise geometry with materials chosen for routine use: special steel provides dimensional stability and wear resistance under repeated engagement. The 50 mm length ensures a consistent contact area for tactile probing and comparative gauging on bench-mounted equipment. Delivered as a single item, this compact measurement accessory is easy to store and to integrate into existing inspection kits, making it a pragmatic choice for production floors where robustness and repeatability matter. Fit into quality-control workflows and documentation Integration into established inspection processes is straightforward: the pin functions as a reference for end-dimension checks and complements micrometre and bore-gauge measurements. Its small footprint supports quick comparative checks during first-article inspections or spot checks in series production. For procurement and inventory, the clear identification and industrial-grade specification help maintain measurement chains and reduce the risk of ambiguous results in acceptance protocols; the technical values permit straightforward inclusion in quality documentation and equipment lists. For reliable end-dimension verification using Metav IndustryLine quality, contact Metav Werkzeuge to discuss availability or to request a specification review by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M323.901 GTIN: 4061905062056 Product: Gauge pin, single, 9.01 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.01 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.029 kg Material: Special steel Features and applications Workshop version Category: Messstifte (gauge pins) Intended use: Final-dimension inspection / end measurements Delivery form: Single item FAQ What is the intended use of this gauge pin? The gauge pin is intended for final-dimension inspection and verification of small bores or end fits, using the Ø 9.01 mm nominal size and the ±0.001 mm tolerance as a comparative reference. Which material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance in workshop conditions, helping to maintain consistent contact geometry over repeated checks. How precise is the measurement reference provided by this pin? With a stated tolerance of ±0.001 mm (1 µm), the pin offers micrometre-level reference precision suitable for high-accuracy acceptance checks and process control tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.02mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm repeatability together with a compact 50 mm length and robust construction for reliable dimensional checks in the workshop; supplied as a single gauge pin in a protective transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or consult Metav's specialists for further specification advice. Gauge pin M323.902 — 9.02 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.902 is a single precision gauge pin intended for end‑dimension inspection and fixture checks in industrial and workshop environments, offering a tight tolerance and compact form for routine quality control tasks. Precision tolerance ±0.001 mm Diameter 9.02 mm for end‑measure fits Solid special steel construction Supplied in transport case Precision where it matters High‑accuracy measurement is the principal benefit of this design: the ±0.001 mm tolerance delivers a fine measurement window that supports strict acceptance criteria and reduces the risk of part rejection in serial production. With a nominal diameter of 9.02 mm and a 50 mm length, the pin provides a stable reference for end‑measure gauges and plug‑gauge checks. The compact geometry limits lever effects and runout, which preserves repeatability during quick inspection cycles and makes the pin suitable as a master for comparative checks on production batches. Durable construction for routine workshop use Constructed from special steel, this workshop version emphasises wear resistance and dimensional stability under frequent handling. The hardened surface and precise grinding process ensure low surface roughness and consistent fit in mating bores, supporting frequent insertion and withdrawal without rapid degradation. The modest mass aids handling while maintaining rigidity; the combination of material and finish extends service life and reduces downtime for replacements, contributing to a predictable inspection workflow in busy shops. Practical handling and integration into inspection workflows Delivered as a single item with individual packaging for safe transport, the gauge pin is straightforward to store and deploy at the inspection bench. The compact size and clear nominal marking simplify inventory management and help technicians select the correct reference quickly. In bench testing or fixture set‑up, the pin functions as a go/no‑go reference or a transfer standard for setting gauges and checking bore diameters, allowing faster throughput and consistent acceptance decisions across repeated cycles. Efficiency and traceability for production environments Using a dedicated pin with a defined tolerance window reduces measurement uncertainty and supports consistent quality reports. The uncomplicated geometry requires minimal training to integrate into existing inspection plans, while the robustness of the workshop version lowers the frequency of replacements. For operations seeking predictable measurement performance with minimal setup time, this single gauge pin offers a cost‑effective, high‑precision reference that aligns with standard quality routines. Choose Metav IndustryLine’s precision gauge pin M323.902 for dependable inspection results and contact Metav Werkzeuge for tailored procurement or specification support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.902 GTIN: 4061905062650 Label: Gauge pin, single, 9.02 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.02 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Material: special steel Workshop version Supplied in transport case Single item supply FAQ What tolerance does the gauge pin have? The gauge pin has a manufacturing tolerance of ±0.001 mm, specified for the Gauge pin M323.902 from Metav IndustryLine. What are the exact diameter and length? Diameter is 9.02 mm and length is 50 mm for the single gauge pin M323.902. Which material is used for the pin? The pin is made from special steel, selected for wear resistance and dimensional stability in workshop use. How is the item supplied and protected for transport? The item is supplied as a single piece and packaged in a transport case to protect the finished surface during handling and shipment. What applications suit this gauge pin? Designed for end‑dimension inspection, fixture set‑up, plug‑gauge reference and routine quality checks in workshops and production lines Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com