Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
2.62mm Gauge Pin, ±0.001 mm Accuracy, Length 50 mm, Workshop Version - Metav IndustryLine
Precision measurement in a compact form: the combination of ±0.001 mm tolerance, a 2.62 mm diameter and a 50 mm length delivers reproducible end‑measure checks with minimal set‑up time; supplied in a protective transport case for safe handling. Order the pin gauge directly via Metav Werkzeuge or consult our experts for application advice. M323.262 Gauge pin – 2.62 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.262 gauge pin is a workshop‑grade inspection pin designed for precise end‑measure checks and fine positioning in toolmaking and quality control. ±0.001 mm tolerance for high precision Diameter 2.62 mm, length 50 mm Workshop‑grade special steel construction Supplied in protective transport case Accuracy that secures production tolerances High‑accuracy measurement reduces rejects and shortens inspection routines. With a declared tolerance of ±0.001 mm, this gauge pin offers micrometric repeatability that supports tight process windows and reliable end‑of‑line checks. The small nominal diameter of 2.62 mm places the component in the micro range, where compact dimensions and low deflection are essential; this makes the pin suitable for precision checks on small bores, jigs and delicate assemblies. The technical specification gives a clear, verifiable basis for pass/fail decisions and traceable production documentation. Built for workshop conditions and longevity A workshop‑grade design and special steel material provide a balance of wear resistance and dimensional stability under repeated use. The pin is supplied individually and protected in a transport case, which reduces the risk of handling damage and preserves the calibrated geometry during storage and transfer between measurement stations. The compact mass also makes the pin easy to position in fixtures and gauges, while the durable surface minimises maintenance intervals and supports consistent measurement results across production batches. Practical use and typical applications This gauge pin serves as an end‑measure reference for finishing, a setting aid for fixtures and a precise master for inspection benches—especially where small diameters must be verified. The compact form factor improves accessibility in confined setups and simplifies measurement sequences in toolmaking and small‑component assembly. Where traceable dimension checks are required, the pin integrates into existing inspection workflows and complements gauge blocks and plug‑gauge systems for quick comparative checks. Its single‑piece supply suits bespoke repairs, replacement tasks and occasional calibration routines without overstocking full sets. For workshop‑ready precision and fast availability from Emmerich, contact Metav Werkzeuge to discuss the M323.262 pin gauge and its use in production or inspection workflows; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.262 GTIN: 4061905057410 Brand: Metav IndustryLine Category: Gauge pins Core data Diameter: 2.62 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop‑grade design Supplied in protective transport case Single‑piece supply Application: end‑measure checks and precision set‑ups FAQ What tolerance can be expected from this gauge pin? The M323.262 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometric repeatability suitable for tight inspection criteria. Is the pin supplied individually or as part of a set? This item is supplied individually; the single‑piece supply supports targeted replacement and small‑batch testing without purchasing full sets. Which materials and applications are typical for this pin? Made from special steel, the pin is intended for workshop use in end‑measure checks, fixture set‑ups and small‑component inspection where compact reference diameters are required. How should the pin be stored to maintain accuracy? Storage in the provided protective transport case preserves the measuring face and reduces contamination, ensuring consistent measurement performance over time. Can the pin be used in confined or hard‑to‑reach fixtures? Yes, the compact 2.62 mm diameter and 50 mm length make the pin well suited to confined access situations and small‑bore measurements. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.63mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of extreme precision (±0.001 mm), a compact 2.63 mm diameter and a 50 mm length suited to deep seats; this workshop-grade gauge pin ensures reproducible end-measurements and secure fits. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin (single) M323.263 — 2.63 mm, ±0.001 mm tolerance The gauge pin for precise end-measurements and tight-fit checks in workshop and inspection environments, supplied as a single probe in a transport case. Tolerance ±0.001 mm for highest precision Nominal diameter 2.63 mm for tight fits Length 50 mm suitable for deep measurements Workshop version supplied in transport case Precision that keeps production within tolerance The M323.263 is manufactured to an exacting ±0.001 mm specification, which places it in the range of very high-precision plug gauges for small bores and end measurements. Such a tight tolerance reduces ambiguity during go/no-go checks and minimises the risk of defective assemblies. The small 2.63 mm nominal diameter is ideal where repeatability on micro-scale fits matters; the geometry and finish are optimised to reduce measurement scatter and to interact predictably with seating surfaces. Durable material and workshop-ready packaging Made from special steel, this single gauge pin is designed for routine use in production and workshop settings. The workshop version emphasises robustness while keeping handling straightforward: the 50 mm length provides reach into deeper features without sacrificing control. Delivery in a protective transport case preserves the reference surface during storage and transit, helping to maintain the pin’s metrological condition between inspection cycles and reducing unplanned downtime. Integrates into quality control workflows with ease As a compact reference probe, this item supports rapid inspection steps and clear go/no-go decisions, helping to speed up throughput while safeguarding quality. The small mass and simple geometry make the pin easy to position in inspection fixtures or manual test benches; traceable marking (SKU M323.263) eases inventory control and process documentation. Using a dedicated gauge pin for end-measurements contributes to a predictable measurement process and fewer returns due to assembly misfits. Choose the Metav IndustryLine gauge pin for reliable end-measurements—contact Metav Werkzeuge in Emmerich for tailored delivery and expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.263 GTIN: 4061905058226 Manufacturer: Metav IndustryLine Facts Nominal diameter: 2.63 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Supplied in transport case FAQ What is the intended use for this gauge pin? This gauge pin (M323.263) is intended for precise end-measurements, plug checks and tight-fit verification in workshop and inspection routines. Is the tolerance of ±0.001 mm sufficient for precision fitting? Yes — the ±0.001 mm tolerance places the pin among very high-precision gauges suitable for small-diameter fits and critical assembly checks. What material is the pin made from and how does that affect durability? The pin is made from special steel; this provides a wear-resistant surface and stability in typical workshop conditions. Does the product include protective packaging? Yes — the workshop version of the gauge pin is supplied in a transport case to protect the reference faces during storage and transit. How can the gauge pin be identified in stock or ordering systems? The gauge pin is listed under SKU M323.263 and GTIN 4061905058226 for inventory and ordering purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.64mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high measurement accuracy (±0.001 mm), a compact 2.64 mm diameter and a robust workshop design for reliable end‑measurement tasks; order the M323.264 directly via Metav Werkzeuge or consult our specialists for application advice. M323.264 gauge pin — precision test pin in workshop design, 2.64 mm diameter, ±0.001 mm tolerance M323.264 is a single precision gauge pin intended for end‑measurement and inspection tasks in production and workshop environments. Workshop version for robust handling Diameter 2.64 mm, high-precision fit Tolerance ±0.001 mm for end measurements Delivered in protective transport case Accuracy that secures final inspection results A tolerance of ±0.001 mm positions this gauge pin in the high‑precision class used for final checks and dimensional verification. The extremely fine tolerance ensures repeatable results when measuring critical end dimensions, so measurements become a reliable basis for pass/fail decisions in small‑part production. The compact 2.64 mm diameter and short 50 mm length minimise flex and contact variation, supporting consistent repeatability during routine use. Built for workshop use and straightforward handling The workshop version is manufactured from special steel, providing wear resistance and a tactile feel suited to frequent handling. At just 0.005 kg the pin is easy to manoeuvre while its solid construction maintains stability under normal contact forces. Delivery in a protective transport case keeps the pin secure between uses and during transport, reducing the risk of damage and preserving measurement integrity on the shop floor. Practical applications and production fit Designed for end‑measurements and small‑component inspection, this single test pin is suitable for slot, hole and bore verification where a tight gauge is required. The compact geometry and high accuracy make it a practical choice for quality control benches, toolrooms and precision assembly stations. The designation M323.264 and the clear specification simplify inventory management and traceability within production control systems, supporting documented inspection routines. Contact Metav Werkzeuge today for precise specification sheets or to request the M323.264 from Metav IndustryLine via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.264 GTIN: 4061905058233 Label: Prüfstift, einzeln, 2,64mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.64 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Delivered in a transport case Category: Messstifte Intended use: end measurements FAQ What are the exact diameter and length of the pin? The M323.264 gauge pin has a diameter of 2.64 mm and a length of 50 mm, as specified in the product label. What tolerance can be expected from this test pin? The test pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision end measurements. Which material is used for the pin? The pin is made from special steel, chosen for durability and stable dimensional behaviour in workshop conditions. Is the pin supplied ready for workshop use? Yes, the workshop execution and delivery in a protective transport case make the M323.264 ready for safe handling and storage in production environments. What typical tasks suit this gauge pin? The pin is ideal for end‑measurement tasks such as hole and bore checks, precision inspection of small components and final dimensional verification on assembly benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.65mm Test Pin, ±0.001 mm, Length 50 mm, Workshop Version, Special Steel - Metav IndustryLine
Benefitting from a ±0.001 mm tolerance and a Ø 2.65 mm precision ground diameter, this single gauge pin delivers reliable end‑measure checks in workshop environments; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.265 — single precision gauge pin, Ø 2.65 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.265 is a workshop‑grade single inspection pin designed for precise end‑measure and fit checks in small‑component assembly and inspection tasks. Tolerance ±0.001 mm for high accuracy Diameter 2.65 mm, precision ground Length 50 mm for end‑measure applications Workshop‑grade special steel construction Faster, measurable inspection with micrometric accuracy The gauge pin offers a repeatable ±0.001 mm tolerance that significantly reduces measurement uncertainty during quick pass/fail checks. Because the pin is precision ground to Ø 2.65 mm, it provides a defined reference diameter for end‑measure tasks and go/no‑go assessments. This level of consistency shortens inspection cycles and supports faster decision making on the shop floor, improving throughput without sacrificing traceability or measurement credibility. Built for daily workshop use and safe transport Designed as a workshop‑grade tool, the inspection pin combines a durable special steel construction with a compact 50 mm length that is easy to handle in confined assembly or inspection stations. The low mass contributes to swift handling, while the supplied transport case protects the measuring surface during storage and transfer. The rugged finish helps resist wear from repeated seating in bores and gauges, so the item remains reliable over many inspection cycles. Simple integration into inspection routines and tooling sets The single‑piece design makes the pin straightforward to incorporate into existing pin sets, plug gauges or fixture checks as a reference element for end‑measure verifications. Traceable identification via the SKU simplifies inventory control and replacement planning. For workshops seeking controlled, reproducible fits on small components, this inspection pin provides a compact, low‑maintenance means of verifying critical diameters and mating fits. Discuss specific measurement requirements with Metav Werkzeuge — our specialists in Emmerich advise on application suitability and delivery options for Metav IndustryLine products Technical data SKU: M323.265 GTIN: 4061905054860 Label: Prüfstift, einzeln, 2,65mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.65 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Delivered in transport case Category: Gauge pins (Messstifte) FAQ What level of accuracy does this gauge pin provide? The gauge pin M323.265 offers an accuracy of ±0.001 mm, making it suitable for fine end‑measure checks and tight tolerance verifications in workshop settings. Is the M323.265 suitable for repeated fit checks in production? Yes, the workshop‑grade construction and precision ground surface of the M323.265 are intended for repeated go/no‑go and end‑measure inspections as part of production workflows. What material is the inspection pin made from? This inspection pin is manufactured from special steel, chosen for wear resistance and dimensional stability under typical workshop conditions. Does the product come with a protective case? The M323.265 is supplied with a transport case to protect the measuring surface during storage and transfer. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.66mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, compact 2.66 mm diameter and rugged workshop design—ideal for repeatable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.266 — single inspection pin, 2.66 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.266 is a single inspection pin designed for precise end‑measurement and fit checks in workshop and inspection environments Diameter 2.66 mm with ±0.001 mm tolerance Length 50 mm for end‑measurement checks Workshop design in special steel Supplied in a transport case for secure handling Precision that reduces rework and inspection time The small diameter and tight ±0.001 mm tolerance turn this inspection pin into a reliable reference for dimensional checks where minimal deviation is critical. High repeatability during pin gauging helps to reduce rework and scrap rates by providing a deterministic fit check; the 2.66 mm diameter is manufactured to narrow tolerances to ensure a consistent go/no‑go feel in fixtures and assemblies. In practice, using such a precise reference component shortens inspection cycles and supports faster decision making on the shop floor. Durable construction for everyday workshop use Built as a workshop version and made from special steel, the pin resists routine handling and contact wear while maintaining its measurement properties. The 50 mm length provides sufficient reach for most end‑measurement tasks without compromising stiffness; the small mass (approx. 0.005 kg) aids rapid manual handling and positioning. Supplied in a protective transport case, the pin arrives ready for safe storage and reduces the risk of damage during transit or on the bench—important where repeatability and surface condition affect measurement quality. Practical applications and integration into inspection routines This single inspection pin is suitable for end‑measurements, fit verification and component matching in toolmaking, small‑series assembly and quality control. As a compact, purpose‑built reference part it integrates straightforwardly into existing fixtures and gauges or can be used as a handheld check whenever a defined reference diameter is required. For customers seeking traceable procedures, the component supports standardised inspection routines and can be combined with working gauges to create robust, repeatable measurement steps. Contact Metav Werkzeuge for specific application recommendations on the Metav IndustryLine gauge pin M323.266 or to request a technical data sheet—phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: M323.266 GTIN: 4061905054877 Label: Gauge pin, single, 2.66 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.66 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Workshop version Material: special steel Supplied in transport case Single inspection/gauge pin Intended for end‑measurement checks FAQ What tolerance does the gauge pin provide? The gauge pin M323.266 is manufactured to a tolerance of ±0.001 mm, providing a high‑precision reference for tight fit and end‑measurement checks. Which material is used for this inspection pin? The inspection pin is made from special steel, chosen for wear resistance and durability in workshop environments. What applications suit this pin best? Typical uses include end‑measurements, fit verification and fixture checks in toolmaking, small‑series assembly and general quality control tasks where a precise reference diameter is required. How is the pin delivered and protected? The pin is supplied in a transport case to protect the measuring surface during storage and transportation and to ensure consistent condition at first use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.67mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
This high-precision gauge pin combines ±0.001 mm dimensional accuracy with a 2.67 mm nominal diameter and robust special-steel construction for consistent end‑mass control; supplied in a transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if further specification advice is required. Gauge pin M323.267 — 2.67 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.267 is a workshop-grade precision pin for end-mass checks and dimensional inspection in metrology and production control. 2.67 mm diameter, ±0.001 mm tolerance 50 mm length, workshop version Special-steel construction for wear resistance Delivered in transport case for safe handling Ensure repeatable, sub-micron-capable measurements High repeatability is at the core of this pin's design: the ±0.001 mm tolerance and fine-ground 2.67 mm shaft give a measurable improvement in positional certainty when used for end-mass checks or concentricity verification. In practical terms, the tight tolerance reduces rework and scrap by enabling earlier detection of out-of-tolerance conditions on assembly fixtures and test rigs. The result is a measurable increase in quality-control throughput and fewer downstream interruptions. Built for workshop handling and long service life The workshop-grade construction, realised in special steel, balances hardness with resistance to surface damage so that dimensional integrity persists under frequent use. At 50 mm overall length and approximately 0.005 kg weight, the pin is easy to manoeuvre for manual inspection while still offering a stable engagement in small bores. Supplied in a transport case, the pin remains protected during transit and storage, preserving the ground surface and ensuring consistent contact conditions at the measuring interface. Seamless fit into inspection routines and traceable stockkeeping Supplied under the designation M323.267 (GTIN 4061905054884), this pin integrates neatly into warehouse and inspection processes that rely on clear identification and reproducible artefacts. As a compact gauge pin, it supports quick pass/fail checks and can be used as a reference element in comparative measurement sequences. Backed by the Metav IndustryLine offering, the component benefits from established distribution and quality assurance channels, giving purchasing and QA teams the confidence of a consistent supply. Select the Metav IndustryLine gauge pin M323.267 for precise end‑mass verification and contact Metav Werkzeuge in Emmerich for procurement and specification guidance. Technical Data Article number: M323.267 GTIN: 4061905054884 Label: Gauge pin, single, 2.67 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.67 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Workshop version Material: Special steel Supplied in transport case Category: Gauge pin / measuring pin FAQ What is the permitted dimensional tolerance of this pin? The gauge pin M323.267 from Metav IndustryLine is manufactured to a tolerance of ±0.001 mm, suitable for high-precision end-mass checks. For which inspection tasks is the pin intended? The pin is intended for end-mass control, dimensional inspection and comparative checks in workshop and production metrology as a reference or go/no-go element. What material is used and how durable is it? Made from special steel, the pin offers enhanced wear resistance and maintains contact surface quality under routine workshop conditions. Can this pin be used for small-bore verification? Yes — the 2.67 mm diameter and fine ground finish make the pin appropriate for verification of small bores and locating features within its dimensional range. How is the product delivered and identified? The pin is supplied in a transport case and labelled with SKU M323.267 and GTIN 4061905054884 for clear identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.68mm Test Pin Length 50mm ±0.001mm Workshop Finish, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop robustness, ultra‑fine ±0.001 mm tolerance and a compact 2.68 mm diameter in a 50 mm length to secure reliable end‑measure checks. Order the test pin directly via Metav Werkzeuge or consult the technical advisers for application‑specific guidance. Test pin M323.268 (Metav IndustryLine) — 2.68 mm, ±0.001 mm, 50 mm length A Test pin M323.268 designed as a high‑precision inspection pin for end‑measure reference and workshop gauging applications Ultra‑fine tolerance ±0.001 mm Diameter 2.68 mm for end‑measure checks 50 mm length in workshop execution Made from special steel for stability Consistent results through measurable precision The primary advantage of this inspection component is its ±0.001 mm tolerance, which places it in the high‑precision segment for plug and test pins. Such accuracy reduces ambiguity at the pass/fail boundary and improves repeatability in short‑run inspection tasks. The narrow 2.68 mm diameter, combined with a 50 mm length, makes the component especially suitable for end‑measure verification of small bores and stepped features. In practical terms, the tight specification shortens decision time during quality control and supports fine tolerancing in assembly processes. Material integrity and workshop suitability Constructed from special steel, the pin is engineered for dimensional stability and wear resistance in workshop environments. The material choice balances hardness with sufficient toughness to resist deformation under typical handling and insertion stresses. The workshop configuration indicates a robust finish and handling profile that resists nicks and accidental damage during frequent use. This makes the pin a dependable reference tool for bench inspection as well as for use in simple gauging fixtures where repeatable results matter. Integration into inspection routines and benefits Focusing on workflow, the component is configured as a single test pin that can be adopted directly into existing gauge sets or used as a standalone end‑measure reference. Its compact geometry supports access to confined features and stepped bores where larger gauges cannot reach. The design reduces set‑up time for small‑batch verification and simplifies traceable measurements in production. As a result, quality engineers and machinists gain a pragmatic balance of reach and rigidity for routine checks without the overhead of more complex gauging systems. Traceability, identification and practical notes The test pin carries a manufacturer SKU for clear identification and inventory control and is categorised under gauge pins for straightforward procurement. Where strict process documentation is required, the clear specification of 2.68 mm, 50 mm length and ±0.001 mm tolerance aids in traceable record‑keeping. For applications that demand particular surface conditions or additional finishing, consult the technical advisers to confirm suitability; the supplied data ensures compatibility with standard inspection procedures and end‑measure references. Contact Metav Werkzeuge today for tailored delivery of Metav IndustryLine test pins, specification advice and stock information via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data Article number: M323.268 GTIN: 4061905054891 Manufacturer: Metav IndustryLine Material: Special steel Diameter: 2.68 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Category: Messstifte (gauge pins) Facts Diameter: 2.68 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg GTIN: 4061905054891 Special features Workshop execution Single test pin Intended for end‑measure checks SKU: M323.268 FAQ What tolerance can be expected from this test pin? The test pin is specified with a tolerance of ±0.001 mm, ensuring high‑precision pass/fail decisions for end‑measure verification. Is the pin suitable for small bore inspection and stepped features? Yes, the 2.68 mm diameter and 50 mm length make the pin appropriate for confined bores and stepped measurements common in precision assembly. What material is used and how does it affect durability? The pin is manufactured from special steel, chosen for a balance of hardness and toughness to provide stability and wear resistance in workshop use. Can this pin be integrated into existing gauge sets? The single‑pin configuration is designed for direct incorporation into standard gauge assemblies or for standalone reference use in inspection routines. How is the product identified for ordering and inventory? The product is listed under SKU M323.268 and GTIN 4061905054891 for unambiguous procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.69mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy, compact handling and workshop‑ready robustness to secure reproducible end measurements. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin M323.269 — single test pin, 2.69 mm, ±0.001 mm, 50 mm The Gauge pin M323.269 is a precision test pin for end‑measurement and alignment tasks in workshop metrology, suited to component verification and go/no‑go checks. Workshop version, robust design Diameter 2.69 mm with ±0.001 mm accuracy 50 mm length and low weight 0.005 kg High accuracy for reliable end measurements The gauge pin delivers substantial repeatability by offering a nominal diameter of 2.69 mm with a manufacturing tolerance of ±0.001 mm, making it suitable where tight dimensional control is required. The compact geometry and minimal mass contribute to reduced thermal and handling influences during short‑range checks, so measurements remain consistent. The component is crafted from special steel, providing wear resistance and surface integrity that support repeated insertion and withdrawal in inspection jigs and alignment fixtures. Practical workshop design that speeds up inspection Engineered as a workshop version, the pin combines robust construction with straightforward handling: a 50 mm shaft length and overall low weight (0.005 kg) allow easy positioning in small bores, fixtures or assembly gauges. The simple single‑piece design reduces sources of play and simplifies storage on inspection benches. Clear dimensional marking and compact form factor aid rapid identification and allow efficient use in production sampling routines, saving time while maintaining traceable measurement quality. Seamless fit into metrology and production workflows Traceability and repeatable results are supported by the unit’s clear identification: SKU M323.269 and GTIN 4061905054907 facilitate inventory and inspection documentation. The pin is particularly useful for end‑measurement, alignment and go/no‑go assessment in machining and quality control processes. Reliance on quantifiable characteristics such as diameter, tolerance and length enables objective pass/fail criteria and straightforward integration into existing inspection plans. Metav’s role as a precision partner further emphasises dependable supply and product support for industry and trade. Contact Metav Werkzeuge for application guidance on the Gauge Pin M323.269 — Metav Werkzeuge GmbH can advise on suitability for specific inspection setups; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for detailed information Technical data Article number: M323.269 GTIN: 4061905054907 SKU: M323.269 Facts Nominal diameter: 2.69 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Material: special steel Version: workshop execution Category: gauge pin / test pin Intended use: end measurement and alignment FAQ What accuracy can be expected from this test pin? The gauge pin M323.269 is manufactured to a tolerance of ±0.001 mm, suitable for tasks that require high repeatability in end measurements. Which material is used for the pin and why does it matter? The pin is made from special steel; this material selection ensures surface durability and resistance to wear during repeated use in inspection fixtures. Is the M323.269 suitable for go/no‑go checks on small bores? Yes, the 2.69 mm diameter and rigid single‑piece design make the M323.269 appropriate for go/no‑go assessment and alignment in small bore applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.6mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micron accuracy (±0.001 mm), a compact Ø 2.60 mm profile and a practical 50 mm length for dependable end‑measurement checks in routine production. Order the item directly via Metav Werkzeuge or consult Metav's specialists for application advice. M323.260 Gauge pin — Ø 2.60 mm, ±0.001 mm (Metav IndustryLine) The M323.260 gauge pin is a workshop‑grade inspection pin designed for precise plug and bore checks and end‑measurement tasks in production and inspection environments. Workshop version for routine inspection Diameter 2.60 mm, tolerance ±0.001 mm 50 mm special steel pin for easy handling Supplied in a protective transport case Suitable for end‑measurement and go/no‑go checks Precision that secures production quality The core advantage of this inspection pin is its ±0.001 mm tolerance — equivalent to 1 µm — which provides a level of dimensional certainty that reduces rejects and accelerates quality decisions on the shop floor. Used as a reference for end‑measurements and final size checks, the compact Ø 2.60 mm diameter and consistent geometry improve the repeatability of go/no‑go inspections and comparative gauging. Such micron‑level accuracy is particularly valuable where small clearances and tight fits determine assembly performance or where final dimensions are critical to downstream processes. Built for everyday workshop use Manufactured in special steel, the pin balances wear resistance with manageable handling in daily operations. The 50 mm length offers enough engagement for reliable contact while remaining compact for use in confined setups and fixtures. As a workshop‑grade article, the design supports frequent handling and straightforward integration into inspection rigs or gauges without introducing unnecessary bulk. Delivery includes a protective transport case, ensuring safe transit between stores, machines and measuring benches and preserving the pin's geometry during routine movement. Practical application and operational benefits This inspection pin suits a wide range of tasks — from precise end‑measurements and bore verification to use as a reference gauge in assembly verifications. The single‑piece supply simplifies traceability and storage: each pin can be recorded by its SKU and GTIN and kept ready for immediate use in measurement sequences. Because the design focuses on consistent contact geometry, cycle times for checks can be shortened and measurement uncertainty reduced, supporting leaner control loops and steadier production throughput. For supplementary technical details or application recommendations, Metav's measurement specialists are available to advise on best practices and integration. Order the M323.260 from Metav Werkzeuge for reliable micron‑level checks or contact Metav Werkzeuge's consultants at info@metav-werkzeuge.com / +49 2822 7131930 for tailored application advice Technical data Article number: M323.260 GTIN: 4061905057397 ECLASS: 21170231 Label: Prüfstift, einzeln, 2,60mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.60 mm Tolerance: ±0.001 mm (1 µm) Length: 50 mm Weight: 0.005 kg Special features Workshop version (Werkstatt‑Ausführung) Material: special steel Supplied individually Delivered in a protective transport case Intended for end measurements / final size checks FAQ What is the dimensional tolerance of the pin? The M323.260 gauge pin is specified at ±0.001 mm, which corresponds to 1 µm, ensuring very fine dimensional control for inspection tasks. What material is the gauge pin made from? The pin is manufactured from special steel, chosen for durability in workshop and production use. For which inspection tasks is this pin suitable? The inspection pin is suitable for end measurements, plug and bore verification, go/no‑go checks and use as a reference in small‑part assembly and quality control. How is the item delivered and identified? The pin is supplied individually and shipped in a protective transport case. Identification is by SKU M323.260 and GTIN 4061905057397. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.71mm Gauge Pin Single, ±0.001 mm, Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, a compact Ø 2.71 mm diameter and a resilient special steel finish for reproducible end‑measure checks. Order directly via Metav Werkzeuge or contact the consultants for application advice. Test pin M323.271 — single test pin, Ø 2.71 mm, ±0.001 mm, 50 mm (Metav IndustryLine) A Test pin M323.271 designed for precise end‑measure verification and fixture referencing in workshop metrology environments. ±0.001 mm tolerance Ø 2.71 mm diameter Length 50 mm for end‑measure checks Consistent precision that speeds inspection Engineered for repeatable reference measurements, this gauging pin delivers a tolerance of ±0.001 mm, which substantially reduces measurement uncertainty during routine checks. The fine tolerance makes the pin suitable for tasks that demand minimal deviation, such as end‑face gauging, alignment of fixtures and verification of bore fits. Using a reference pin with defined geometry reduces rework and accelerates quality control cycles, providing a clear productivity advantage on the shop floor. Robust construction for workshop conditions Manufactured from special steel, the component balances hardness and wear resistance while retaining the dimensional stability needed for repeated contact with mating parts. The workshop execution ensures the pin is suitable for everyday use in industrial environments where handling and surface contacts are frequent. A length of 50 mm provides sufficient reach for many fixturing situations, while the compact diameter keeps the pin easy to guide and position in narrow bores or alignment jigs. Practical benefits for inspection and assembly As a single‑piece test pin, the component integrates into existing gauging sets and can be used as a master reference in go/no‑go setups or as a datum for assembly fixtures. The small mass and rigid geometry ensure low thermal drift during short inspection cycles, supporting faster measurement routines. Clear, verifiable specifications simplify documentation and traceability in quality processes, helping to maintain consistent product tolerances across batches. For reliable end‑measure checks, choose the Metav IndustryLine test pin and contact Metav Werkzeuge for procurement and technical guidance. Technical data Article number: M323.271 GTIN: 4061905054921 Manufacturer: Metav IndustryLine Dimensions and accuracy Diameter: 2.71 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Materials and special features Material: special steel Version: workshop execution Delivery: single test pin FAQ What tolerance can be expected from this test pin? The test pin M323.271 has a specified tolerance of ±0.001 mm, making it suitable for high‑precision reference and inspection tasks in workshop metrology. Is the material suitable for frequent contact with hardened mating parts? The pin is made from special steel designed for wear resistance; for contact with heavily hardened components, inspection intervals should be matched to the application to monitor wear. Can this pin be used as a master for go/no‑go gauging? Yes, the single test pin functions as a master reference for go/no‑go arrangements and datum setting within assembly and inspection fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.72mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Benefit from workshop‑grade robustness combined with sub‑micron accuracy: the pin's ±0.001 mm tolerance and precision ground finish ensure reliable end‑measure checks and repeatable fits. Order the item directly via Metav Werkzeuge or consult the technical team for application advice. M323.272 gauge pin — workshop test pin, 2.72 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.272 is a workshop‑grade gauge pin designed for precise end‑measure and fit checks in inspection, fixture set‑up and pin‑block assemblies. Sub‑micron tolerance ±0.001 mm Diameter 2.72 mm, precision ground Length 50 mm, workshop‑grade design Delivered in transport box for protection Consistent sub‑micron accuracy for inspection tasks The M323.272 functions as a dedicated gauge pin for end‑measure verification and gauge assembly work. Its ±0.001 mm tolerance combined with a precision ground surface minimises measurement uncertainty and ensures stable contact conditions during go/no‑go checks or plug‑gauge comparisons. In practical terms, the tight tolerance reduces make‑or‑break decisions at assembly and inspection points, shortening rework loops and supporting tighter process control. Robust workshop construction for reliable handling Constructed from special steel, the pin offers a balance of wear resistance and dimensional stability suited to everyday workshop use. The 50 mm length and compact 2.72 mm diameter make the pin easy to seat in fixtures and pin blocks while retaining sufficient overhang for handling. The workshop‑grade finish tolerates normal handling and protects functional surfaces; delivery in a transport box keeps the part protected between uses and during transport, preserving the measuring edge and extending service life. Designed for repeatable workflows and fast inspection Integration into inspection benches, pin holders or comparison setups is straightforward thanks to the standardised size and the pin's repeatability. The robust geometry supports fast exchange in testing sequences and reduces setup time in small‑batch or series production. The product is traceable via GTIN 4061905055379, supporting inventory management and procurement processes; Metav IndustryLine’s quality filter further ensures consistent supply and suitability for industrial inspection applications. For precision end‑measure checks, request the M323.272 from Metav Werkzeuge — Metav’s Emmerich team can advise on fitment, set composition and supply at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.272 GTIN: 4061905055379 Manufacturer: Metav IndustryLine Core specifications Diameter: 2.72 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Materials & features Material: Special steel Workshop‑grade design Precision ground surface Supplied in transport box FAQ What is the diameter and tolerance of this gauge pin? The gauge pin has a diameter of 2.72 mm with a tolerance of ±0.001 mm, suitable for tight fit‑checking and precise inspection tasks. Can the pin be used in pin blocks and fixture plates? Yes, the pin’s standard geometry and 50 mm length make it compatible with common pin‑block systems and fixture set‑ups. Is the material specified for the pin suitable for workshop use? The pin is made from special steel, selected for wear resistance and stability under typical workshop conditions. Is there a calibration certificate included with the item? No specific calibration certificate is stated in the product data; any calibration requirements should be clarified with Metav Werkzeuge prior to purchase. How is the pin delivered to protect the measuring surface? The part is supplied secured in a transport box to protect the precision surface during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.73mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of a compact, highly‑accurate gauge pin that combines ±0.001 mm tolerance with a 2.73 mm diameter and a robust 50 mm length for reliable end‑measure verifications; supplied in a protective transport case, the workshop‑grade design supports repeatable inspections and easy handling — order via Metav Werkzeuge or request advice from our consultants. M323.273 Gauge Pin — 2.73 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.273 gauge pin is a workshop‑grade precision pin designed for end‑measure checks, go/no‑go verifications and fixture set‑up tasks in inspection and toolmaking environments Workshop-grade construction Diameter 2.73 mm, tolerance ±0.001 mm Length 50 mm for repeatable end measurements Supplied in protective transport case Accuracy that shortens inspection cycles A ±0.001 mm tolerance places this gauge pin in the high‑precision segment for workshop inspection tools. The exceptionally tight tolerance reduces measurement uncertainty and speeds decision making during incoming inspection or in‑process checks. Because the pin is manufactured from special steel, dimensional stability and wear resistance are improved, which sustains repeatability over many cycles and reduces the need for frequent replacement. This combination of tight tolerance and durable material supports faster throughput in quality control workflows. Robust handling and protected transport for daily use With a 50 mm active length and workshop‑grade finishing, the pin balances reach and rigidity for routine end‑measure tasks. The shorter overall form factor makes it easy to position in fixtures and jigs while remaining resistant to bending under normal handling. Delivery includes a protective transport case, intended to prevent transit damage and maintain the pin’s calibrated condition during storage and movement — the case is optimised for transport rather than permanent storage. These practical design choices reduce handling errors and protect the critical gauge surface. Simple integration into measurement routines The gauge pin is suitable for plug‑gauge style checks, verification of end‑masses and dimensional references in assembly fixtures. Its 2.73 mm nominal diameter matches common small‑bore inspection needs, enabling consistent reference points across inspection plans. The high precision and stable material allow the pin to serve as a transfer standard between manual gauges and CMM fixturing, improving traceability and helping to maintain process capability indices in serial production. Fewer rejections and clearer tolerance decisions are the direct benefits. Ready for workshop procurement and stock management As a compact, high‑accuracy test pin, the item is straightforward to specify and stock. The M323.273 designation and compact packaging make it easy to identify in stores and on inventory lists, while the special steel construction supports long service life under typical workshop conditions. For purchasing and planning, inclusion in routine inspection kits or as a replacement reference in jigs reduces downtime and keeps measurement baselines consistent across shifts. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge for technical advice or to secure the M323.273 gauge pin for immediate dispatch — Metav Werkzeuge provides detailed product guidance and reliable logistics from Emmerich. Technical data Article number: M323.273 GTIN: 4061905055386 Manufacturer: Metav IndustryLine Dimensions & tolerances Diameter: 2.73 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Features & materials Workshop version Material: special steel Supplied in transport case Category: gauge pin (Messstifte) FAQ What is the intended use of this gauge pin? The gauge pin is intended for end‑measure verifications, plug‑gauge checks and fixture set‑up tasks; the M323.273 provides a stable reference diameter of 2.73 mm with ±0.001 mm tolerance for these operations. How durable is the M323.273 under regular workshop use? Made from special steel and delivered in a protective transport case, the M323.273 is designed for durable routine use and maintains dimensional stability across repetitive checks. Is the transport case suitable for long‑term storage? The supplied case is intended for safe transport and short‑term storage to protect the measuring surface; it is optimised for transit rather than permanent long‑term storage of precision gauges. Can this pin be used as a reference in fixture calibration? Yes — its tight tolerance and stable material make the M323.273 suitable as a transfer standard between manual gauges and fixture set‑ups in quality control processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.74mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine ±0.001 mm tolerance, a compact 2.74 mm diameter and a stable 50 mm reference length to reduce inspection uncertainty and rework in serial production; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application support. M323.274 gauge pin — single precision plug, 2.74 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.274 gauge pin is a single precision measuring plug designed for end-dimension verification and hole inspection in workshop and inspection environments. High precision ±0.001 mm tolerance Diameter 2.74 mm for precise fits 50 mm length for reliable reference Workshop version in special steel Precision that cuts rework and inspection time This measuring plug delivers industrial-grade accuracy with a tolerance of ±0.001 mm, making it suitable for high-precision fit checks and final inspection of critical end dimensions. Such a fine tolerance reduces the need for repeat measurements and downstream rework, which translates directly into improved throughput and lower scrap rates. The small 2.74 mm diameter is ideal for tight holes and dowel seats where micron-level clearance matters; by explaining the practical effect of the tolerance, non-specialists can understand that less variation at the gauge stage means more consistent assembly quality on the line. Robust form for repeatable handling in the workshop Manufactured from special steel and specified as a workshop version, the pin balances wear resistance with tactile stability during manual gauging. The 50 mm length offers a reliable reference for both end-face and through-hole checks, helping technicians maintain consistent measurement posture and contact. A compact, single-pin format simplifies storage and transport within inspection kits, while the nominal weight supports steady seating in fixtures. The construction focuses on repeatability rather than decorative finishes, so longevity in everyday shop use is prioritised. Seamless fit into inspection routines and traceable part checks Designed for straightforward integration in common metrology routines, the gauge pin suits go/no-go tests, plug gauges and ad hoc verification stations for end dimensions. Labelling and the SKU allow simple stock identification and traceability in quality records; the pin assists in establishing a reproducible reference that upstream and downstream teams can rely on. Backed by Metav’s positioning as a precision partner, the product supports lean inspection workflows and helps smaller operations access the measurement accuracy typically reserved for larger shops. Choose the Metav IndustryLine gauge pin when critical tolerances demand dependable reference measurement — contact Metav Werkzeuge in Emmerich for specialist advice and assured supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.274 GTIN: 4061905055393 eClass: 21170231 Facts Diameter: 2.74 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop version Single gauge pin for end-dimension checks FAQ What tolerance does the gauge pin provide? The M323.274 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, suitable for very fine inspection and fit verification. Which applications suit this measuring pin? It is intended for end-dimension checks and hole inspection tasks where a compact 2.74 mm reference helps verify fit and clearance in assemblies. What material is used for the pin? The plug is made of special steel, selected to balance wear resistance and stable seating during repeated measurements. Is the M323.274 supplied as a single item or part of a set? This SKU is a single gauge pin supplied individually for insertion into inspection kits or fixtures. How does this pin support production quality? By providing a reproducible reference with tight tolerance, the pin reduces measurement variation and helps prevent rework and assembly issues. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.75mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, special steel stability and a compact 50 mm length for reliable end‑measure checks and streamlined workshop inspection workflows. Order directly via Metav Werkzeuge or consult the technical team for application support. Pin gauge, single — 2.75 mm, ±0.001 mm accuracy (Metav IndustryLine) The pin gauge, single 2.75 mm is a workshop‑grade end‑measure reference pin designed for precise gauging, quick go/no‑go checks and repeatable inspection tasks in mechanical and assembly environments. High-precision ±0.001 mm tolerance Special steel for stable dimensional integrity 50 mm overall length, compact design Supplied in protective transport case Reliable end‑measure references for repeatable inspection A workshop‑grade gauge pin with a ±0.001 mm tolerance provides a measurable improvement in process certainty for dimensional checks. The very small incremental deviation means the pin functions as a dependable reference when verifying bore sizes, plug gauges or mating features. By reducing measurement uncertainty, the pin contributes to fewer reworks and more consistent assembly acceptance rates, which translates into better throughput in production and inspection loops. Robust material and compact form suited to busy benches Constructed from special steel, the pin resists wear and preserves calibrated dimensions under frequent handling. The compact 50 mm overall length and 2.75 mm nominal diameter make it especially suited to confined inspection points and end‑measure tasks where access is limited. The workshop‑execution design balances stiffness with manoeuvrability so that operators can perform quick checks without compromising the integrity of the measured interface. Practical handling, protection and workflow traceability Delivery in a protective transport case ensures the gauge pin arrives ready for use and stays protected during storage or transit. The single‑unit configuration supports targeted replacements in tooling sets and simplifies inventory control. Clear labelling and the provided identifiers make it straightforward to include the item in existing quality documentation, improving traceability within metrology routines and supporting a structured inspection regime. For repeatable end‑measure confidence choose the Metav IndustryLine pin gauge M323.275 — contact Metav Werkzeuge for ordering or precise application advice via info@metav-werkzeuge.com or telephone +49 2822 7131930 Technical data Article number: M323.275 GTIN: 4061905055911 Material: Special steel Accuracy: ±0.001 mm Length: 50 mm Diameter: 2.75 mm Weight: 0.006 kg Packing: Protective transport case included Version: Workshop execution Category: Gauge pin (single) Facts Nominal diameter: 2.75 mm Overall length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Single gauge pin for end‑measure tests Workshop execution for frequent use Protective transport case for handling and storage Category: Messstifte (gauge pins) Story trigger: end‑measure applications FAQ What is the declared tolerance of this gauge pin? The gauge pin is specified with a tolerance of ±0.001 mm, providing a high level of dimensional stability for exacting inspection tasks with the Metav IndustryLine M323.275. Is the pin suitable for routine workshop use? Yes; the workshop‑execution construction and special steel material make the pin robust enough for frequent handling and quick go/no‑go checks at the inspection bench. Does the item come with protective packaging? Delivery includes a protective transport case, ensuring the pin remains undamaged in transit and during storage. Can this gauge pin be used for calibration reference in quality documentation? The pin’s declared accuracy and clear identification make it suitable for inclusion in traceability records and routine inspection documentation within a quality system. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.76mm Test Pin ±0.001 mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade construction, sub-micron accuracy and compact handling to ensure reliable end‑measurement in the workshop; order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. M323.276 Pin Gauge (2.76 mm, ±0.001 mm) — Metav IndustryLine The M323.276 pin gauge is a single precision test pin designed for high‑accuracy end‑measurement and dimensional verification in workshop and inspection routines. Precision ±0.001 mm tolerance Diameter 2.76 mm, length 50 mm Workshop-grade special steel construction Compact single-pin format for end measurements Repeatable accuracy for end‑dimension checks The pin delivers a stated ±0.001 mm manufacturing tolerance, which translates into highly repeatable results when used as a reference for end‑measurements and fit checks. In practical terms, this level of precision supports tight quality requirements and helps to identify deviations at the micrometre scale, reducing the risk of assembly issues or rework. The specification is especially relevant where small clearance fits and interchangeability must be proven reliably. Robust build tailored to workshop use Constructed from special steel in a workshop execution, the pin balances wear resistance with straightforward handling. With a nominal diameter of 2.76 mm and a 50 mm overall length, the format is compact enough for quick manual checks yet long enough to reach recessed seats and short bores. The solid construction minimises deformation during normal use and contributes to consistent contact geometry, which in turn maintains measurement integrity over repeated cycles. Practical integration into inspection workflows This single‑pin format is intended for end‑measurement tasks such as final diameter verification, go/no‑fit checks and small‑bore gauging within production or service environments. The M323.276 can be incorporated into routine inspection sets or used as a trusted reference when validating machined components. Clear identification via GTIN and SKU simplifies traceability in stock lists and documentation, supporting transparent quality management and auditability. Contact Metav Werkzeuge today to clarify suitability for specific inspection tasks or to arrange supply of the M323.276 pin gauge directly from Emmerich — our specialists provide application guidance and reliable delivery. Technical data Article number / SKU: M323.276 GTIN: 4061905055928 Manufacturer: Metav IndustryLine Facts Diameter: 2.76 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: special steel Workshop execution Single pin delivery Intended use: end‑measurement and verification FAQ What level of precision does this pin achieve? The M323.276 pin gauge is manufactured to a tolerance of ±0.001 mm, providing micrometre‑class repeatability suitable for high‑precision end‑measurements. Is the pin suitable for routine workshop fitting checks? Yes, the workshop‑grade construction and compact 2.76 mm / 50 mm format make the pin well suited for daily fit and verification tasks on small bores and assemblies. How is the product identified for ordering and documentation? The pin is listed under SKU M323.276 with GTIN 4061905055928, simplifying inventory control and traceability. Which material is used for the pin? The gauge is produced from special steel, chosen for its balance of hardness and resistance to wear in typical workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.77mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability and workshop durability: the precise ±0.001 mm tolerance combined with a 2.77 mm gauge diameter and a 50 mm length ensures consistent end‑dimension checks and reduced rework. Order the gauge pin directly via Metav Werkzeuge or consult the team for specification matching. Gauge pin M323.277 — 2.77 mm diameter, ±0.001 mm tolerance The Gauge pin M323.277 is a workshop‑grade inspection pin designed for end‑dimension verification and fixture probing in precision assembly and quality control. Diameter 2.77 mm precision pin Tolerance ±0.001 mm for exact gauging 50 mm length for probe and fixture use Workshop‑grade special steel construction Reduce measurement uncertainty with sub‑micron repeatability This inspection pin delivers a measured tolerance of ±0.001 mm, enabling reliable go/no‑go checks and tight dimensional control on small bores and component ends. The extremely fine tolerance reduces the need for secondary checks and helps shorten inspection cycles in repetitive production. By using a stable gauge diameter of 2.77 mm, setup variance is minimised, which supports faster decision‑making on the shop floor and a more efficient quality workflow. Built for everyday workshop handling and repeat use Constructed from special steel and specified as a workshop‑grade item, the pin withstands routine handling and repetitive seating in gauges and fixtures without rapid wear. The material choice balances hardness and machinability to keep contact surfaces intact while preserving the reference diameter. Robust construction ensures dimensional stability over many inspection cycles, which translates into dependable readings and fewer rejected parts due to measurement artefacts. Practical form factor for fixture access and traceability With a 50 mm length the pin provides sufficient reach for recessed features and can be used as a fixed reference in modular checking rigs. Supplied as a single item, it integrates easily into bespoke inspection assemblies as an end‑stop or probe. Traceability is supported by the assigned SKU and GTIN, aiding inventory control and quality documentation for batch records and process audits. Contact Metav Werkzeuge for tailored advice on integrating this workshop‑grade gauge pin into inspection routines or to request batch availability and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.277 GTIN: 4061905055935 Label: Gauge pin, single, 2.77 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.77 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg ECLASS: 21170231 Special features Material: special steel Supply: single piece Execution: workshop‑grade Category: gauge pins FAQ What is the intended use of this gauge pin? The gauge pin M323.277 from Metav IndustryLine is intended for end‑dimension verification, fixture probing and simple go/no‑go gauging tasks in production and inspection environments. Is the tolerance of ±0.001 mm achievable in daily shop use? Yes, when used with stable fixturing and calibrated reference equipment the ±0.001 mm tolerance of this Metav IndustryLine gauge pin can be maintained for routine checks. Can this pin be used in modular checking fixtures? The 50 mm length and precise 2.77 mm diameter make the pin suitable for integration as an end‑stop or probe in modular and bespoke checking fixtures. How is the material specified and what does it mean for wear? The pin is made of special steel, a balanced choice that offers good wear resistance for workshop applications while maintaining the reference diameter over many cycles. What identifiers support traceability for audits and reorders? Traceability is provided via SKU M323.277 and GTIN 4061905055935, enabling straightforward inventory management and documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.78mm Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.001 mm tolerance, special steel construction and a protective transport case for dependable end‑size inspection. Order the gauge pin directly via Metav Werkzeuge or ask the technical consultants for application advice. Metav IndustryLine Gauge pin M323.278 – Ø 2.78 mm, ±0.001 mm, L 50 mm The gauge pin M323.278 is a single inspection pin designed for precise end‑measure checks and routine workshop gauging. Workshop‑grade construction Tolerance ±0.001 mm for repeatable checks Diameter 2.78 mm, length 50 mm Supplied in protective transport case Precision where measurement matters This single inspection pin delivers ±0.001 mm tolerance, making it suitable for demanding end‑size verifications and high‑repeatability tasks. The narrow diameter combined with a 50 mm length yields a compact profile that reduces lever‑action errors during insertion and withdrawal, supporting consistent repeatability in production sampling. Constructed from special steel, the pin resists wear while maintaining its dimensional stability under typical workshop conditions, which reduces rework and supports efficient quality control routines. Built for routine inspection and longevity The workshop version of this test pin emphasises robustness and practical handling. The protective transport case preserves the gauge between uses and simplifies safe storage on the shop floor, while the compact format speeds up inspection cycles and minimises handling time. As a result, measurement steps integrate smoothly into incoming inspection, in‑process checks and final release procedures — delivering detectable benefits in throughput and process reliability without complex setup. Practical integration and application guidance Designed as a straightforward reference standard for end‑measure checking, the pin performs well for slot, bore and plug checks where a defined diameter gauge is required. The nominal diameter of 2.78 mm and weight of 0.006 kg make the item easy to position and quick to exchange in test fixtures. For specific test plans or batch inspection strategies, Metav’s technical advisors can provide guidance on appropriate use cases and complementary tooling to maintain traceability and measurement efficiency. Contact Metav Werkzeuge today to discuss the M323.278 gauge pin for reliable end‑measure inspection or to request tailored advice from our metrology specialists Technical data Article number: M323.278 GTIN: 4061905055942 Label: Prüfstift, einzeln, 2,78mm, +/- 0.001 mm Länge 50 mm Numbers / core technical data Diameter: 2.78 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Material: Special steel Versions / special features Workshop execution Protective transport case included End‑measure application (inspection/test pin) FAQ What is the primary application of this gauge pin? The gauge pin M323.278 is intended for end‑size inspections and routine plug‑type checks in workshop and production environments. What level of accuracy does this test pin provide? Accuracy is specified at ±0.001 mm, suitable for high‑precision go/no‑go verification and repeat measurement tasks. What material is the pin made from? The pin is made from special steel, selected for wear resistance and dimensional stability under normal workshop use. How is the item supplied for transport and storage? The product is supplied in a protective transport case to preserve the gauge between uses and simplify handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.79mm Precision Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm repeatability and a compact 2.79 mm diameter for reliable end‑measure checks; the workshop‑grade construction and individual protective case ensure safe transport and immediate use — order the gauge pin directly via Metav Werkzeuge or consult our specialists if further specification is required. Gauge pin M323.279 — 2.79 mm, ±0.001 mm high‑precision (Metav IndustryLine) The M323.279 gauge pin is a single inspection pin for precise end‑measure verification and tight‑fit checks in fine mechanical and workshop environments High‑precision ±0.001 mm accuracy Diameter 2.79 mm manufactured to tolerance 50 mm shaft in special steel construction Delivered in a protective transport case Precision where tolerance is critical Small‑diameter inspection needs demand predictable results; the ±0.001 mm tolerance of this gauge pin minimises measurement uncertainty in pass/fail checks and fine‑fit assemblies. Ground to a nominal 2.79 mm diameter, the pin is designed for repeatable insertion checks and go/no‑go verification of bores and guide holes. This level of precision reduces rework and scrap rates while supporting consistent quality control routines. Robust design for everyday workshop handling Specified as a workshop version, the single‑piece pin combines a slender 50 mm shaft with special steel for wear resistance and dimensional stability. Supplied individually and protected in a protective transport case, the pin is ready for transport between inspection benches without surface damage. The lightweight design also aids rapid handling during batch checks, keeping inspection throughput efficient in production and maintenance settings. Integrates easily into existing inspection processes Traceability and ordering are straightforward: the pin is listed under SKU M323.279 and GTIN 4061905055959, facilitating inventory control and procurement. As an inspection pin for end‑measure checks, it complements plug and pin gauge sets as well as bespoke fixtures for precision assembly. Backed by Metav’s industry experience, the component supports reliable measurement workflows and quick replacement strategies to keep production running smoothly. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine M323.279 gauge pin can be specified for inspection tasks, request detailed technical clarification, or arrange procurement via +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.279 GTIN: 4061905055959 Weight: 0.006 kg Length: 50 mm Diameter: 2.79 mm Accuracy: ±0.001 mm Material: Special steel Facts Nominal diameter: 2.79 mm Shaft length: 50 mm Mass: 6 g Tolerance: ±0.001 mm SKU: M323.279 Special features Workshop version Supplied individually Protective transport case included Suitable for end‑measure checks and tight‑fit verification Manufacturer brand: Metav IndustryLine FAQ What tolerance does the gauge pin hold? The M323.279 gauge pin is manufactured to an accuracy of ±0.001 mm, suitable for high‑precision end‑measure verifications. What material is used for the pin? The shaft is made from special steel, selected for dimensional stability and wear resistance in workshop use. Is the pin supplied ready for transport? Yes — the gauge pin is supplied individually in a protective transport case to prevent damage during handling and transit. Which applications suit this inspection pin? This pin is intended for end‑measure checks, go/no‑go verification of bores and guides, and general tight‑fit inspections in fine mechanical and workshop environments. How can the product be identified for reordering? Identification is via SKU M323.279 and GTIN 4061905055959, which support procurement and inventory management. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.7mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
A compact, high-precision gauge pin combining tight tolerance and robust workshop handling: Ø 2.70 mm with ±0.001 mm accuracy and a 50 mm shank length deliver repeatable end‑size checks; available directly from Metav Werkzeuge or via consultation with our metrology specialists. M323.270 Gauge Pin – Ø 2.70 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.270 is a single precision gauge pin designed for end‑size verification and fit checks in workshop and inspection environments. High-precision tolerance ±0.001 mm Compact Ø 2.70 mm for micro measurements Workshop-grade construction and finish Supplied in a protective transport case Reliable precision for repeatable checks The M323.270 offers a ±0.001 mm tolerance, making it suitable where repeatability and minimal clearance variation are critical. As a single gauge pin, it supports precise plug and fit checks for small bores and mating parts. Classified within the micro range (measurement ranges up to 10–100 mm), this pin is optimised for fine mechanical tasks where short shank length reduces bending and handling error. The tight tolerance reduces rework and speeds up inspection cycles, so measurement routines become a dependable part of production control. Built to withstand workshop use Manufactured from special steel, the pin is finished for workshop durability while retaining the dimensional stability required for accurate gauging. The 50 mm shank provides sufficient engagement for secure fit checks without excess overhang, and the low mass supports easy handling during rapid inspection. Delivery in a protective case ensures safe transport and prevents incidental damage between uses, maintaining calibration and reducing downtime for replacements. Integrates smoothly into inspection workflows This precision plug is well suited to assembly, quality control and toolroom use where fast, unequivocal Go/No‑Go assessments are needed. A single, accurately ground diameter simplifies documentation and traceability in inspection plans and drawings. At approximately 0.005 kg, the pin is lightweight for repetitive operations yet engineered to hold form under normal workshop conditions. Using a dedicated gauge pin for end‑size verification shortens measurement time and improves confidence in go/no‑go decisions. Request supply of the Metav IndustryLine M323.270 gauge pin from Metav Werkzeuge to standardise end‑size checks in the workshop — contact info@metav-werkzeuge.com or call +49 2822 7131930 for procurement advice and availability Technical data Article number: M323.270 GTIN: 4061905054914 Label: Prüfstift, einzeln, 2,70mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.70 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Measurement range (max): 2.7 mm Special features Workshop execution Delivered in protective transport case Material: special steel Intended use: end‑size verification / fit checks FAQ What tolerance does this gauge pin provide? The M323.270 gauge pin is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑size verification in small bores. Which material is used for the pin? The pin is made from special steel, offering a balance of wear resistance and dimensional stability for workshop inspection. Is the pin supplied ready for workshop use? Yes — the pin is finished for workshop use and is supplied in a protective transport case to prevent damage during handling and storage. For which measurement category is this pin intended? This gauge pin falls into the micro category (measurement ranges up to 10–100 mm) and is tailored to fine mechanical applications such as small bore, fit and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.81mm Test Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of pinpoint 2.81 mm diameter control with a guaranteed ±0.001 mm tolerance and robust workshop construction for reliable end‑measure checks; supplied as a single 50 mm pin in a transport case for safe logistics. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.281 gauge pin — 2.81 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) A M323.281 gauge pin designed for precise end‑measure verification and fit checks in workshop inspection and assembly applications 2.81 mm diameter, tolerance ±0.001 mm 50 mm nominal length, workshop execution Made from special steel for wear resistance Supplied in transport case for safe logistics Precision that reduces rework and secures assembly tolerances The core advantage of this precision pin is its exceptionally fine ±0.001 mm tolerance, which translates into consistent repeatability when checking bores, dowel fits or calibration masters. In practice, a stable reference pin with a 2.81 mm diameter simplifies go/no‑go comparisons and minimises measurement uncertainty during incoming inspection or final assembly. The small mass and compact geometry allow fast handling, so measurement cycles remain efficient without sacrificing traceability. Built for daily workshop use and handling Constructed from special steel, the pin balances hardness and toughness to withstand frequent seating and removal from mating bores. The 50 mm overall length provides sufficient engagement for reliable contact while remaining easy to manoeuvre in tight workstations; the workshop version is intentionally ruggedised for routine use rather than fragile laboratory handling. For transport and storage the item is supplied in a transport case, reducing risk of damage between shifts and preserving the calibrated condition of the reference surface. Integrates simply into quality control workflows As a single‑piece reference tool, the pin supports rapid end‑measure checks, plug gauge comparisons and setup operations in jigs and fixtures. Clear identification via GTIN 4061905056819 aids inventory control and traceability within production documentation. The compact design and known tolerance make the pin suitable as a repeatability check for pneumatic fixturing or as a datum during gauge block assembly. For buyers seeking dependable supply, Metav’s position as a European quality filter ensures accessible stock and consistent part quality from Emmerich. Contact Metav Werkzeuge to request the M323.281 gauge pin for precise end‑measure checks and secure immediate dispatch from our Emmerich site, or ask our consultants for tailored technical advice Technical data Article number: M323.281 GTIN: 4061905056819 Brand: Metav IndustryLine Facts Diameter: 2.81 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: Special steel Workshop execution Supplied in transport case Application: end‑measure checks Category: Gauge pins FAQ What is the exact tolerance of this gauge pin? The M323.281 gauge pin by Metav IndustryLine is specified with a tolerance of ±0.001 mm, suitable for fine fit and end‑measure verification. Is the pin suitable for routine workshop use? Yes, the workshop execution and special steel construction make the gauge pin M323.281 robust enough for regular inspection tasks. How is the pin supplied and identified for inventory? The pin is supplied singly in a transport case and carries GTIN 4061905056819 for straightforward inventory and traceability. Can this pin be used as a datum for fixture set‑up? The fine tolerance and stable geometry make the M323.281 an appropriate reference for fixture set‑up and quick go/no‑go checks in production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.82mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometre-level tolerance, robust workshop construction and compact dimensions for repeatable end‑measurement routines; order directly via Metav Werkzeuge or ask the consultants for application advice. Gauge Pin M323.282 — single gauge pin, 2.82 mm, ±0.001 mm, 50 mm A Gauge Pin M323.282 designed for precise end measurements and inspection tasks in workshop and production settings. Tolerance ±0.001 mm Diameter 2.82 mm Length 50 mm Workshop-grade special steel Precision where it counts This compact inspection pin is engineered for measurement tasks that demand sub‑100‑micrometre certainty: with a tolerance of ±0.001 mm and a nominal diameter of 2.82 mm, the pin provides consistent end‑measurement results that reduce rework and speed up quality decisions. The slim geometry and tight manufacturing tolerances make the component suitable for calibration checks, gauging seats and fixture verifications where repeatability is essential. Durable construction for everyday workshop use Constructed from special steel in a workshop‑oriented version, the pin balances surface hardness with corrosion resistance to withstand routine handling and insertion cycles. At a length of 50 mm and a mass of just 0.006 kg, the item is easy to seat in small fixtures and quick to manoeuvre during inspection sequences, while the material choice supports longevity under frequent contact and mechanical alignment tasks. Integration into inspection workflows Supplied as a single unit, this gauge pin is intended for immediate use in manual and semi‑automated inspection setups. Traceability is supported by the clear identifier M323.282, which simplifies inventory management and documentation in the production chain. The compact dimensions allow insertion into narrow bores and the pin’s consistent form aids in rapid pass/fail checks or as a reference for measuring instruments. Improve throughput with reliable end measurements Adopting this precision pin in measurement routines strengthens process control: fewer uncertain readings mean faster throughput, lower scrap rates and clearer acceptance criteria. The combination of micrometre tolerance and a workshop‑ready design makes it a practical choice for quality teams seeking reliable, repeatable reference tools without complex handling requirements. Contact Metav Werkzeuge for a technical consultation on how the Metav IndustryLine M323.282 can be integrated into existing gauging procedures — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.282 GTIN: 4061905056826 Brand: Metav IndustryLine Specifications Diameter: 2.82 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Materials & Features Material: Special steel Workshop execution Supplied as a single unit Intended use: end measurements FAQ What applications suit this gauge pin best? The M323.282 gauge pin is optimised for end‑measurement tasks, fixture checks and narrow‑bore gauging in workshop and production environments. Is the M323.282 suitable for use as a reference in inspection jigs? Yes. The repeatable diameter and tight ±0.001 mm tolerance make the pin appropriate as a reference element in inspection jigs and simple go/no‑go setups. Which material is used and why does it matter? The pin is made from special steel; this ensures durability and stable contact surfaces under frequent insertion and alignment work. How is the item supplied and identified? The product is supplied as a single unit and is identified by article number M323.282 and GTIN 4061905056826 for traceability. Can this pin reduce measurement variability on the shop floor? Used as a consistent reference, the M323.282 helps lower variability in end‑measurement routines and supports clearer acceptance limits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.83mm Gauging Pin, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from a reliable combination of high-precision tolerance, wear-resistant special steel and a compact 50 mm length for repeatable end‑measure checks in workshop settings. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single Ø 2.83 mm – ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin, single Ø 2.83 mm designed for precise end‑measure verification and use as a reference in inspection fixtures and assembly jigs. ±0.001 mm tolerance for fine verification Special steel for enhanced wear resistance 50 mm length for stable handling in fixtures Workshop version optimised for daily use High-precision verification for quality control The gauge pin is manufactured to a tight ±0.001 mm tolerance, making it suitable for critical checking tasks where even minimal deviation matters. This level of accuracy supports reliable go/no‑go assessments and dimensional sampling during incoming inspection or final measurement steps. By using a reference pin with such a fine tolerance, measurement uncertainty in routine checks is reduced and process-related rework is minimised, which improves production throughput and traceability. Durable construction to withstand workshop demands Constructed from special steel and supplied in a workshop design, the pin combines surface hardness with dimensional stability to resist wear during repetitive insertion and contact operations. The material choice and finish preserve the calibrated diameter over time, which maintains measurement consistency across extended usage cycles. Corrosion resistance and mechanical robustness translate directly into lower replacement frequency and predictable inspection results on the shop floor. Compact form that integrates easily into fixtures With a nominal diameter of 2.83 mm and a 50 mm length, the pin provides a compact reference that is straightforward to position in small bores, jigs and assembly aids without adding unnecessary bulk. Its light mass contributes to easy handling while the length ensures secure seating for both axial and lateral support in fixture applications. The compact geometry is particularly useful for fine mechanical assemblies and end‑measure controls where space is limited but repeatability is essential. Clear product identity and traceability for procurement Identified as SKU M323.283 and classed under gauge pins, this single test pin carries a GTIN for clear stock management and traceability. The combination of measurable specifications—diameter, tolerance and length—allows straightforward comparison with drawing requirements and inspection plans. For workshops and laboratories that standardise on reliable reference items, this pin provides a compact, high‑accuracy solution that fits a wide range of verification tasks. For tailored advice or to secure supply of Metav IndustryLine gauge pins, contact Metav Werkzeuge GmbH in Emmerich for personal consultation and prompt delivery via info@metav-werkzeuge.com or +49 2822 7131930 Technical details SKU: M323.283 GTIN: 4061905056833 Brand: Metav IndustryLine Category: Gauge pins Numbers / Core technical data Nominal diameter: 2.83 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Accuracy class: ±0.001 Materials / Special features Material: Special steel Design: Workshop execution Application: End‑measure checks and fixture references Packaging: single piece FAQ What accuracy can be expected from this gauge pin? The gauge pin M323.283 is specified at ±0.001 mm tolerance, giving high‑precision performance for fine verification tasks. What material is the pin made from? The item is made of special steel, chosen for wear resistance and dimensional stability in workshop conditions. Is the pin suitable for use in small bores and fixtures? Yes, the compact diameter of 2.83 mm and a length of 50 mm make the pin suitable for insertion into small bores and for use as a reference in inspection fixtures. How is this product identified for ordering and inventory? This gauge pin is listed as SKU M323.283 and carries GTIN 4061905056833 for procurement and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.84mm Test Pin, ±0.001 mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high‑precision fit verification and a tight tolerance of ±0.001 mm to ensure consistent go/no‑go checking and end‑measurement reproducibility in production and inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice and stocking options. Gauge pin M323.284 — 2.84 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.284 designed for high‑precision end measurements and fit testing in metrology and workshop inspection tasks. Diameter 2.84 mm ±0.001 mm tolerance Solid special steel for dimensional stability 50 mm measuring length for deep bore verification Workshop version for robust everyday use Accurate fit verification with micron-level control The compact inspection pin offers a diameter of 2.84 mm with an exceptionally tight tolerance of ±0.001 mm, making it suitable for precision fit and end‑measurement tasks where repeatability is critical. As a hardened reference element produced in a workshop specification, the pin provides stable dimensions under normal handling and ensures reliable results when used as a reference for hole gauges, plug checks or assembly clearance tests. The small mass and compact geometry support rapid handling and minimal thermal drift during short‑term measurement cycles. Durable construction for consistent repeatability Manufactured from special steel, this single gauge pin balances hardness with corrosion resistance to maintain profile and roundness across repeated use. The 50 mm usable length is optimised for checking deeper bores without undue flexing, while the workshop design emphasises practical robustness for daily inspection tasks. By combining material choice and geometrical control, the pin preserves repeatability and reduces the need for frequent replacement in routine quality checks. Integration into inspection workflows and measurement jigs The pin functions as a stable reference for comparative checks and jig validation, supporting quick pass/fail assessments on production lines. Its slim form factor suits confined fixtures and allows easy pairing with dial or digital comparators for rapid transfer measurements. Where traceable benchmark readings are required, the pin acts as a consistent master that helps streamline set‑up and reduce cycle time for frequent dimension checks. Practical considerations and handling tips Given its fine tolerance and small diameter, handling with care is advised: avoid knocks and store the pin in a protected tray to preserve surface condition and dimensional integrity. The low weight and compact size make it simple to incorporate into a standard inspection kit. For precise alignment in measuring fixtures, the pin’s nominal dimensions minimise measurement uncertainty when used in combination with calibrated instruments and stable environmental conditions. Contact Metav Werkzeuge to discuss the M323.284 gauge pin for your inspection needs or to request stocking options — email info@metav-werkzeuge.com or call +49 2822 7131930 to speak with a technical consultant. Technical data Article number: M323.284 GTIN: 4061905056840 Material: Special steel Diameter: 2.84 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Facts Measuring principle: Reference gauge pin Usable length: 50 mm Tolerance class: ±0.001 mm Mass: 0.006 kg Special features Workshop version Single item delivery Suitable for end‑mass and fit testing Compact form for fixture integration FAQ What tolerance does the gauge pin offer? The gauge pin delivers a tolerance of ±0.001 mm, providing micron‑class control for high‑precision fit checks and end‑measurement verification. Which material is used for this inspection pin? The M323.284 is made from special steel, selected to balance dimensional stability and wear resistance for routine workshop use. What is the usable length of the pin for bore checks? The pin has a measuring length of 50 mm, suitable for verifying deeper bores and assemblies while maintaining stiffness for reliable readings. Can the pin be used in production jigs and fixtures? Yes; the compact geometry and tight tolerance make the pin well suited as a reference element in fixtures, go/no‑go setups and comparator arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.85mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of ultra-fine tolerance together with robust workshop design for repeatable end-measure checks; the ±0.001 mm accuracy and 50 mm length make this pin suitable for high-precision gauging tasks in production and inspection. Order via Metav Werkzeuge or consult the Metav team for application advice. M323.285 Gauge Pin — Single precision gauge pin, 2.85 mm diameter, ±0.001 mm tolerance The M323.285 Gauge Pin is a single precision gauge pin for end-measure and fit checks in workshop and inspection environments, optimised for repeatable dimensional control and straightforward handling Single precision gauge pin 2.85 mm Tolerance ±0.001 mm 50 mm length for end-measure checks Supplied in a transport case Consistent metrology through sub-millimetre accuracy A tolerance of ±0.001 mm positions this gauge pin among precision tools for demanding inspection tasks; the very tight tolerance reduces ambiguity when checking bore fits, plug gauges and mating parts. The small diameter combined with the fine dimensional control means deviations are identifiable at a stage where corrective action is still economical. Designed for repeatability, the pin supports reliable go/no-go assessments and gives a clear, objective basis for pass/fail decisions in production control. Durable workshop construction for everyday use Constructed from special steel, the pin resists wear while maintaining a stable measuring surface over many cycles. The workshop version emphasises robustness and handling: a 50 mm usable length provides sufficient engagement for end-measure checks without unnecessary cantilever. Supplied in a transport case, the pin is protected during storage and transit, reducing the risk of surface damage that could compromise measurement quality. The compact mass and ergonomic profile aid quick placement into fixtures or bores. Integrates smoothly into inspection and tooling workflows This precision pin is ideal for end-mass and fit verification, bench checks and dimension validation in small-batch production or quality labs. The simple geometry makes it compatible with standard gauging fixtures and inspection jigs; the result is lower setup time and fewer sources of measurement uncertainty. For workshop environments that demand traceable, repeatable checks on small diameters, the pin delivers a clear measurement outcome that supports process control and reduces rework. Contact Metav Werkzeuge for application-specific advice or to request detailed drawings and stock availability from our Emmerich warehouse. Technical Data Article number: M323.285 GTIN: 4061905056857 Brand: Metav IndustryLine Facts Diameter: 2.85 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What is the exact tolerance of the gauge pin? The gauge pin has a tolerance of ±0.001 mm, which ensures high-precision checks for small-diameter fits and end-measure inspections. Which applications suit this gauge pin best? The pin is intended for end-measure checks, fit verification and dimensional control of small bores and mating parts in workshop and inspection environments. Is the pin supplied ready for use and protected for transport? The pin is supplied in a transport case to protect the measuring surface and to simplify storage and handling prior to use. What material is the pin made from? The pin is made from special steel, selected for wear resistance and dimensional stability under normal workshop conditions. Can the pin be used in fixture- and jig-based gauging setups? Yes, the simple geometry and precise diameter make the pin suitable for integration into standard gauging fixtures and inspection jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com