Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
2.3mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
The combination of ±0.001 mm accuracy, a compact 2.30 mm diameter and a 50 mm length ensures repeatable reference measurements and secure fit in inspection fixtures; order via Metav Werkzeuge or consult our specialists for integration into existing quality processes. Test pin M323.230 — gauge pin, 2.30 mm, ±0.001 mm (Metav IndustryLine) Test pin M323.230 is a precision gauge pin for end‑measurements and fit checks in production and inspection environments High precision ±0.001 mm tolerance Diameter 2.30 mm for tight-fit gauges 50 mm length workshop version Supplied in a protective transport case Accurate reference measurements with minimal setup The M323.230 test pin is designed as a stable reference for pass/fail checks, plug gauges and fixture verification. With a diameter of 2.30 mm and a high-accuracy tolerance of ±0.001 mm, the pin delivers measurable improvements to inspection repeatability. The compact form and 50 mm length make it suitable for confined gauge bores and stack arrangements; the small mass and rigid geometry reduce bending and thermal shift during short-term usage. Built from special steel, the pin provides wear resistance and consistent surface finish that supports long service life and predictable mating behaviour. Integrates easily into routine quality control workflows As a single, workshop-grade gauge pin, this item suits manual testing stations and automated fixtures alike. The combination of precise diameter control and narrow tolerance means fewer false rejects and clearer go/no-go decisions, improving throughput in small-batch and series production. The pin’s modest weight (approximately 0.004 kg) and compact profile simplify handling and reduce the inertial load on measuring jigs. Supplied in a protective transport case, the component remains protected between shifts and during transfer, helping to preserve calibration and minimise downtime for replacements. Traceability, compatibility and practical benefits Each gauge pin is identifiable via its SKU M323.230 and GTIN 4061905057564, supporting inventory management and traceability in regulated environments. The workshop execution denotes a robust finish suitable for everyday metrology tasks while the material choice ensures compatibility with typical mating parts. For users who require consistent interfacing with plug gauges, fixture pins or comparator setups, this pin offers a reliable datum with minimal setup time. The product’s small dimensions and high precision are particularly advantageous when measuring small bores, dowel fits or when establishing a series of reference gauges for production control. Contact Metav Werkzeuge in Emmerich to discuss how the Metav IndustryLine test pin M323.230 can be incorporated into inspection routines, or request advice by phone +49 2822 7131930 or by e‑mail at info@metav-werkzeuge.com Technical data Article number: M323.230 GTIN: 4061905057564 SKU: M323.230 Facts Diameter: 2.30 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop execution Single test pin delivery Supplied in protective transport case FAQ What tolerance can be expected from this gauge pin? The test pin M323.230 is manufactured to a tolerance of ±0.001 mm, making it suitable for high-precision reference and fit checks in inspection and gauge systems. Is the pin suitable for use in production fixtures and gauges? Yes, the Metav IndustryLine gauge pin M323.230 is a workshop-grade component intended for fixture integration, plug gauges and manual inspection jigs. What material is used and how does it affect wear? The pin is made from special steel, providing good wear resistance and surface stability that helps retain dimensional integrity under normal workshop usage. How is the item identified for traceability? Identification is available via SKU M323.230 and GTIN 4061905057564, facilitating stock control and traceability in quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.41mm Gauge Pin Single ±0.001mm Accuracy 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, robust specialist steel construction and workshop-ready packaging for reliable end-measure checks. The M323.241 pin gauge delivers repeatable results with a tolerance of ±0.001 mm and a compact 50 mm length, enabling precise fit and end‑dimension verification in production and quality control. Order directly via Metav Werkzeuge or contact our consultants for application advice. Pin gauge M323.241 – single, Ø 2.41 mm, tolerance ±0.001 mm (Metav IndustryLine) A Pin gauge M323.241 designed for high‑precision end‑measure verification and fit checks in workshop and inspection environments High precision tolerance ±0.001 mm Diameter 2.41 mm for fine fit checks 50 mm specialist steel shaft Workshop version with transport case Precise measurement for consistent Go/No‑Go checks The pin gauge offers a tolerance of ±0.001 mm, a level of accuracy that supports fine fit verification and end‑measure inspection where small deviations matter. This high precision reduces rework and shortens decision cycles on the shop floor because measurements are directly comparable and repeatable. The small diameter makes the gauge ideal for checking bores, pins and mating holes where clearance must be validated to micrometre‑level tolerances. Robust construction tailored to workshop use Manufactured from specialist steel, the shaft is engineered for dimensional stability and wear resistance during frequent handling. The 50 mm working length is a practical compromise between reach and rigidity, keeping bend and handling error to a minimum, while the workshop specification emphasises durability under regular use. Where traceable calibration history is required, the product is delivered ready for integration into quality routines and routine inspection sets. Practical handling and transport safety The single pin is supplied as an individual gauge and comes packaged for transport to preserve the measuring surface and ensure safe handling. The compact mass and balanced geometry allow steady manual insertion and minimise user‑induced error during fit checks. A workshop‑oriented design supports frequent inspection cycles: the gauge is easy to store with other measuring tools and simple to identify in kits or cases used across production and metrology benches. Application scenarios and operational benefit This pin gauge is particularly suited to end‑measure verification, plug checks and reference checks during assembly or final inspection. Using a standardised gauge with ±0.001 mm tolerance helps to align process control with inspection acceptance criteria and shortens feedback loops between production and quality. For operations that require consistent, verifiable fit checks, the gauge is a compact and reliable element of a broader measurement strategy. For precise workshop checks choose the Metav IndustryLine pin gauge M323.241 and contact Metav Werkzeuge for tailored advice or ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.241 GTIN: 4061905054211 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 2.41 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: specialist steel Delivered single (individual pin) Workshop specification Supplied in transport case FAQ What is the intended use of this pin gauge? The M323.241 pin gauge is intended for end‑measure verification, fit and clearance checks in workshop and inspection settings. How tight is the dimensional tolerance of the gauge? This Metav IndustryLine pin gauge has a tolerance of ±0.001 mm, suitable for high‑precision fit checks. Is the gauge delivered individually or in sets? The item is supplied as a single pin gauge, packaged for safe transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.42mm Test Pin Single ±0.001mm Accuracy Length 50mm Workshop Version - Metav IndustryLine
Precision end-measurement work benefits from the combination of workshop-grade construction, ±0.001 mm tolerance and a stable 50 mm length that supports reproducible seating. Order the gauge pin directly via Metav Werkzeuge or consult the Metav specialists if further clarification is required. M323.242 Gauge pin — 2.42 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) M323.242 is a compact gauge pin designed for precise end‑measurements and fixture checks in workshop and inspection environments Workshop-grade execution Diameter 2.42 mm ±0.001 Length 50 mm for end measurements Delivered in protective transport case Engineered precision that reduces inspection uncertainty The pin delivers micrometre-level repeatability thanks to its declared ±0.001 mm tolerance, making it suitable where small deviations matter. As a hardened, single test pin with a 2.42 mm nominal diameter, it supports exact fit checks and end‑measurements in gauge blocks, alignment fixtures and component checking stations. The close tolerance reduces rework by providing a reliable reference dimension for repeat measurements, which is particularly valuable in processes where traceable dimensional control minimises scrap and downtime. Material choice and form factor for reliable handling Manufactured from special steel, the pin combines surface hardness with dimensional stability for consistent seating and low wear during repeated use. The 50 mm overall length is a practical compromise: long enough to reach into pockets and through holes, yet short enough to prevent bending under typical handling loads. The workshop execution offers robust finishing for everyday mechanical use and ensures the pin remains serviceable in busy production and maintenance environments. The modest mass supports easy manual handling while maintaining contact stability during measurement routines. Practical delivery and application in production workflows Supplied as a single unit in a protective transport case, the pin arrives ready for safe storage and immediate deployment on the shop floor or in the inspection lab. The compact format suits insertion into pin gauges, go/no‑go fixtures and comparative setups where a fixed reference dimension is needed. The product is identified as M323.242 and is particularly useful for end‑dimension verification, set‑up checks and small‑bore validation tasks. The clear specification and robust finish make it straightforward to incorporate into existing quality-control procedures without additional preparation. Recommend Metav IndustryLine gauge pins for consistent end‑measurement results; contact Metav Werkzeuge for product availability and detailed technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.242 GTIN: 4061905055133 Brand: Metav IndustryLine Facts Diameter: 2.42 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Delivered in transport case Category: gauge pins (Messstifte) FAQ What is the declared dimensional tolerance of this pin? The declared tolerance of the M323.242 gauge pin is ±0.001 mm, suitable for high‑precision end‑measurements. Is this pin appropriate for end‑measurement and fixture checks? Yes, the M323.242 test pin is designed for end‑dimension verification, fixture alignment and small‑bore checks where a fixed reference diameter is required. Which material is used and how does it behave in a workshop environment? The pin is made from special steel, selected for a combination of hardness and dimensional stability to withstand regular mechanical handling in workshop conditions. Is the gauge pin supplied ready for use and protected in transit? The item is supplied as a single unit and delivered in a protective transport case for safe handling and storage. Can the pin be incorporated into existing pin‑gauge sets or fixtures? Yes, the M323.242 gauge pin is compatible with fixtures and pin‑gauge assemblies that accept a 2.42 mm reference diameter. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.43mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade durability, ±0.001 mm dimensional accuracy and a compact 50 mm length for reliable end‑measure checks; order directly via Metav Werkzeuge or consult the advisers for application support. Gauge pin M323.243 — Ø 2.43 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The gauge pin M323.243 is a workshop‑grade measuring pin designed for precise end‑measure and dimensional checks in quality control and inspection tasks. Workshop‑grade accuracy ±0.001 mm Ø 2.43 mm nominal diameter Length 50 mm for end‑measure checks Supplied in a secure transport case Precision that supports process control The small nominal diameter and tight tolerance of ±0.001 mm make this pin a tool for high‑resolution checking where minimal variation is permissible. Used for end‑measure verification and plug checks, the Ø 2.43 mm dimension provides a defined reference that helps to reduce measurement uncertainty in repetitive inspection routines. The clearly specified tolerance translates directly into predictable pass/fail decisions on the shop floor and supports statistical process control by supplying consistent reference data. Durable construction for everyday workshop use Manufactured from special steel, the pin is executed as a workshop‑grade component that withstands handling and routine use. The choice of material ensures dimensional stability and resistance to wear under standard inspection sequences without claiming specific hardness values. At a length of 50 mm, the geometry balances reach and rigidity so that alignment and insertion into small bores are straightforward, while the compact form mitigates deflection during measurement. Practical design for inspection workflows Delivered as a single unit and protected in a transport case, the pin arrives ready for use and for safe storage between measurements. The lightweight construction (approx. 0.005 kg) makes it easy to handle in fixture setups and portable inspection kits. Identified as SKU M323.243, the item is suitable for repetitive end‑measure tasks, gauge racks, and quick interchange checks in incoming inspection or final control stations where defined reference dimensions are required. Benefit for quality assurance and traceability Integrating this gauge pin into inspection routines improves the reliability of dimensional decisions and shortens verification cycles, thereby supporting throughput and reducing rework. The clear specification of diameter, length and tolerance simplifies documentation and archive processes for batch inspections. As a workshop‑oriented measuring element, it contributes to consistent quality evidence when combined with calibrated measurement instruments and documented inspection procedures. For secure supply and expert advice on integrating Metav IndustryLine measuring elements into production checks, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 and request SKU M323.243 Technical Data Article number: M323.243 GTIN: 4061905055140 Label: Prüfstift, einzeln, 2,43mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.43 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Material: Special steel Workshop version Supplied in a transport case Single piece delivery FAQ How precise is the gauge pin for dimensional checks? The gauge pin M323.243 is specified to ±0.001 mm, suitable for fine end‑measure verification and repeatable pass/fail assessments. Is the pin suitable for routine workshop inspection? Yes; the workshop‑grade design and special steel construction make the pin appropriate for daily inspection tasks and portability within a quality department. What protection does the item have during transport and storage? The pin is supplied in a transport case to protect the measuring surface and facilitate safe storage between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.44mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Combining workshop-grade construction, a tight ±0.001 mm tolerance and a compact 2.44 mm diameter, this gauge pin provides a dependable reference for end‑measurement tasks and small-part inspection. Order the M323.244 directly via Metav Werkzeuge or ask our consultants if needed. M323.244 Gauge pin – 2.44 mm diameter, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) The M323.244 Gauge pin is a compact reference pin designed for precise end‑measurements and inspection work in workshop and small‑parts metrology High precision tolerance ±0.001 mm Nominal diameter 2.44 mm for fine gauges Length 50 mm, workshop-grade special steel Delivered in protective transport case Faster decisions with micrometric accuracy A tight ±0.001 mm tolerance reduces uncertainty when checking bore sizes, plug gauges or end measurements, so measurement results can be interpreted with confidence. The small nominal diameter of 2.44 mm is tailored for fine gauges and micro components where repeatability matters; this makes the pin particularly useful for quality control steps that must be completed quickly without compromising traceability. By converting a dimensional requirement into a clear pass/fail reference, inspection cycles become shorter and documented outcomes more reliable. Robust workshop design for everyday handling Constructed from special steel and specified as a workshop execution, the pin withstands routine handling and offers consistent surface quality for repeatable contacts. The 50 mm length balances reach and rigidity for small assemblies, while the light mass allows precise placement without affecting the measured part. Delivery in a protective transport case minimises transport damage and helps preserve the reference condition between uses, supporting durability and long‑term reliability in a production environment. Simple integration into inspection workflows The compact geometry and standard form factor suit a wide range of inspection fixtures and manual gauges, enabling straightforward incorporation into existing measuring rigs. With a small footprint and a precise contact surface, the pin serves as a stable reference for end‑of‑line checks, manual comparison gauges and fixture verification. Clear, measurable specifications support documentation and procurement processes, and the compact weight simplifies handling and positioning during rapid inspection tasks. For availability, batch details or application advice on the Metav IndustryLine gauge pin M323.244 contact Metav Werkzeuge: phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.244 GTIN: 4061905055157 Name: Gauge pin, 2.44 mm, ±0.001 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 2.44 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Materials & features Material: special steel Workshop execution Supplied in protective transport case Precision class: ±0.001 mm FAQ What tolerance does the M323.244 gauge pin provide? The M323.244 gauge pin is specified to ±0.001 mm, making it suitable for high‑precision inspection of small bores and reference features. What is the pin made from and how robust is it for workshop use? This gauge pin is manufactured from special steel and supplied in a workshop execution, offering durable contact surfaces for regular inspection tasks. How is the gauge pin delivered and protected during transport? The M323.244 is delivered in a protective transport case, which helps to prevent damage and maintain the reference condition during storage and transit. Is the diameter suitable for micro and small-part inspection? With a nominal diameter of 2.44 mm and compact geometry, the pin is optimised for micro components and fine‑tolerance checks in workshop and small‑parts metrology. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.45mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
High-precision gauge pin with a 2.45 mm diameter and ±0.001 mm tolerance delivers reproducible end-measurements and long service life thanks to hardened special steel; supplied in a protective transport case for safe handling. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.245 – single gauge pin, 2.45 mm, ±0.001 mm, 50 mm length The Gauge pin M323.245 is a single high-precision end gauge designed for dimensional verification and final-size inspection in workshop metrology. Diameter 2.45 mm with ±0.001 mm tolerance Hardened special steel for wear resistance Supplied in a protective transport case Precise measurements that support reliable inspection results The core advantage of this gauge pin is its measurement accuracy: a nominal diameter of 2.45 mm held to ±0.001 mm gives a stable reference for end measurements and functional gauging. In practice, this level of tolerance reduces uncertainty in pass/fail checks and enables consistent checks on small bores, plug gauges and verification fixtures. The compact 50 mm length with low mass supports easy handling and repeatable seating in inspection jigs, while the sturdy finish maintains form over repeated cycles. Durable workshop design for everyday metrology tasks Built as a workshop version, this pin combines robustness with metrology-grade precision. The use of special steel increases wear resistance under repetitive contact, which extends service intervals and reduces replacement frequency. Delivery in a protective transport case safeguards the ground reference surface during storage and transit, ensuring that the datum remains intact until use. The light weight and compact geometry make the pin suitable for handheld checks as well as incorporation into measuring fixtures. Practical applications and integration in quality processes This gauge pin is intended for end-size verification and is suitable for use in inspection benches, fixture setup and incoming part control where small-diameter accuracy is required. The geometry and tolerance make it a reliable reference for calibrating small plug gauges or checking component bores close to the nominal size. Traceability is simplified by the clear SKU and GTIN labelling, supporting inventory control and documentation in quality management systems. Choose Metav IndustryLine's precision gauge pin for reproducible end measurements — contact Metav Werkzeuge in Emmerich for procurement or technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.245 GTIN: 4061905055522 Label: Gauge pin, single, 2.45 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.45 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop version Supplied in protective transport case Application focus: end measurements ECLASS: 21170231 FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 2.45 mm with a manufacturing tolerance of ±0.001 mm (SKU M323.245). Is the pin suitable for repeated workshop use? Yes, the workshop version is made from special steel and is supplied in a protective case to preserve the reference surface during repetitive handling. For which types of inspection is this pin intended? The pin is designed for end-size verification, functional gauging and fixture setup where a precise small-diameter reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.46mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Reliable production control benefits from the combination of ±0.001 mm repeatability, a compact 2.46 mm diameter and a 50 mm usable length—ideal for precise end‑dimension checks and fixture references. Order the gauge pin directly via Metav Werkzeuge or consult our technical advisers for component integration. Gauge pin, single, 2.46 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The Gauge pin, single, 2.46 mm, ±0.001 mm, length 50 mm is a precision inspection pin for end‑dimension verification and reference fits in workshop quality control. Workshop-grade design ±0.001 mm tolerance Diameter 2.46 mm for tight fits Length 50 mm for deep bores Accurate end‑dimension inspection for fewer rejects A pin with a ±0.001 mm specification offers substantial accuracy for end‑dimension checks where interchangeability and tight fits are required. The fine tolerance reduces measurement scatter during routine inspections, supporting tighter process control and fewer downstream reworks. By using a hardened, wear‑resistant special steel shaft, the inspection pin keeps geometric stability over frequent contact cycles, which is vital when recording reproducible results on small bores and reference features. Compact geometry that simplifies access and positioning The compact 2.46 mm diameter and 50 mm length balance accessibility with handling stability. The small cross‑section permits insertion into narrow holes and recesses, while the 50 mm length provides enough engagement to reach end faces without compromising control during measurement. The single‑piece design minimises alignment errors, so fixtures and gauge assemblies can be referenced reliably. This geometry is particularly useful in end‑measure applications where access is restricted but dimensional certainty cannot be compromised. Workshop robustness tuned to inspection routines Made from special steel, the pin is specified for repetitive workshop use and resists surface damage that would otherwise bias measurements. The product’s precision grade ensures that inspection steps—whether performed at a bench comparator, inside a jig or as part of a manual verification routine—produce comparable results. This reliability supports process documentation and traceability in production lines that prioritise consistent tolerances and reduced scrap rates. Practical integration into metrology workflows As a precision inspection component, the pin functions as a reference element in fixture set‑up and short‑range dimensional verification. Its compact form factor allows easy inclusion in instrument kits or control plans where small bore checks are frequent. When combined with standard measuring instruments, the pin helps establish clear pass/fail criteria for finishing processes, improving throughput by shortening decision times and reducing unnecessary milling or rework steps. For specification matching or to include this Metav IndustryLine gauge pin in inspection kits, contact Metav Werkzeuge in Emmerich for advice or procurement via info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: M323.246 GTIN: 4061905055539 SKU: M323.246 Category: Gauge pin / inspection pin Manufacturer: Metav IndustryLine Core specifications Diameter: 2.46 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Workshop version Single inspection pin Material: Special steel Intended use: End‑dimension checks and reference fits FAQ Is this pin suitable for small‑bore inspection? The gauge pin is designed for small‑bore applications; its 2.46 mm diameter and 50 mm length permit insertion into narrow holes for end‑dimension verification. What level of precision can be expected in routine use? With a tolerance of ±0.001 mm, the inspection pin provides high‑precision reference conditions suitable for tight tolerances in workshop quality control. What material is used for the shaft and why does it matter? The shaft is made of special steel, chosen for its dimensional stability and resistance to wear, which helps maintain measurement integrity over repeated use. Can this pin be used as a reference in fixture set‑ups? Yes—the single‑piece construction and precision tolerance make the pin well suited as a reference element in fixture and jig alignment procedures. Is the product delivered as a single item and how is it identified? The item is supplied as a single gauge pin and is identified by SKU M323.246 and GTIN 4061905055539 for clear inventory and procurement handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.47mm Gauge Pin Length 50mm ±0.001mm Workshop Finish in Case - Metav IndustryLine
High-precision 2.47 mm diameter and ±0.001 mm tolerance combined with a robust special‑steel design ensure repeatable inspection and end‑measurement performance on the shop floor. Benefit from a compact, transport‑ready kit that supports reliable go/no‑go and set‑up tasks. Order directly via Metav Werkzeuge or consult our technical advisers for application guidance. Gauge pin M323.247 — 2.47 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The gauge pin M323.247 is a single precision test pin designed for fine inspection work, end‑measurements and tight‑fit checks in workshop and quality‑control environments. ±0.001 mm tolerance for precise measurements Diameter 2.47 mm for tight fit checks 50 mm overall length for extended reach Special‑steel workshop construction, case included Ensure measurement reliability with micrometre‑grade accuracy A ±0.001 mm tolerance places this inspection pin in the high‑precision category for small‑diameter checks, making it suitable where repeatability and minimal measurement uncertainty are critical. The fine 2.47 mm diameter gives predictable contact geometry for bore gauging, plug‑fit verification and reference checks. Because the tolerance is held to the micrometre level, the pin serves as an effective benchmark for pass/fail testing and for setting comparative gauges, reducing the risk of false rejections and saving time during routine inspection. Durable workshop design for frequent use and transport Manufactured from special steel, the pin is engineered for everyday workshop handling and offers corrosion resistance and wear stability under normal inspection loads. The 50 mm overall length provides additional reach where shallow bores or recessed features must be assessed without sacrificing rigidity. Supplied in a transport case, the component stays protected between uses, which preserves the calibration state and minimises handling damage — a practical advantage for busy production or maintenance teams who move measuring tools between workstations. Practical application: where this test pin brings value This single test pin is optimised for precise end‑measurements, go/no‑go checks and fixture set‑up where small diameters are concerned. Typical uses include bore verification, alignment checks in assembly jigs and validation of mating parts during final inspection. The compact geometry and high tolerance make it particularly useful in fine‑mechanical contexts and toolmaking, where consistent contact conditions and repeatability matter more than bulk. The clear specification simplifies integration into existing QC procedures and reduces interpretation effort for technicians. Contact Metav Werkzeuge for availability and tailored advice on the Metav IndustryLine gauge pin M323.247 — our specialists will help confirm suitability for specific inspection tasks and arrange supply directly from Emmerich. Technical data Article number: M323.247 GTIN: 4061905055546 Brand: Metav IndustryLine Category: Gauge pin / Test pin Facts Diameter: 2.47 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Material: Special‑steel Workshop specification Supplied in transport case Single, individual pin FAQ What is the primary use of this gauge pin? The gauge pin M323.247 (Metav IndustryLine gauge pin, SKU M323.247) is intended for precise end‑measurements, bore checks and go/no‑go tasks in inspection and set‑up routines. Is this test pin suitable for routine shop‑floor use? Yes — the Metav IndustryLine test pin is made from special‑steel and supplied in a transport case to withstand frequent handling and movement between workstations. How tight is the diameter tolerance and what does it mean for inspection? The diameter tolerance of ±0.001 mm ensures micrometre‑level repeatability, enabling reliable pass/fail decisions and consistent comparative measurements. Can this pin be used for setting gauges and fixtures? Yes. The 50 mm length and precise diameter make it suitable for setting and verifying fixtures, particularly where small diameters require exact reference standards. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.48mm Test Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of high-precision tolerance ±0.001 mm, compact 2.48 mm diameter and robust 50 mm length for repeatable end‑measure verification; supplied in a transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.248 – 2.48 mm, ±0.001 mm, Metav IndustryLine A gauge pin M323.248 designed for precise end‑dimension checks and reference measurements in workshop and inspection environments. High-precision tolerance ±0.001 mm Diameter 2.48 mm for fine bore checks Length 50 mm for stable contact depths Workshop grade with transport case Consistent precision for critical end‑measure checks The gauge pin delivers a tolerance of ±0.001 mm, which places it in the class of high‑precision inspection pins suitable for tasks where minimal dimensional deviation is required. The extremely tight tolerance reduces measurement uncertainty during plug or reference checks and supports reliable repeatability in batch inspection. By using a finely controlled pin diameter, measurement chains such as bore validation, plug gauge comparison and end‑dimension sampling become more predictable, lowering the risk of undetected non‑conformances. Robust construction and safe handling for busy workshops Manufactured from special steel, the pin is optimised for workshop conditions while retaining metrological performance. Its 50 mm length provides sufficient engagement for stable contact without excessive overhang, and the compact mass (approx. 0.005 kg) makes the pin easy to position in repetitive operations. Delivery in a transport case protects the gauge during transit and storage, preserving the measuring surface and avoiding accidental damage between uses — a practical advantage when instruments are moved between benches or sent to external inspection stations. Practical application and integration into inspection workflows With a nominal diameter of 2.48 mm, the pin is intended for fine bore verification, end‑measure controls and as a reference element within gauge assemblies. The single‑piece design facilitates use as a master pin in comparator setups or as a physical check pin for assembly and testing fixtures. In production environments the component supports rapid go/no‑go decisions and provides a reproducible datum for downstream processes, helping maintain throughput without sacrificing measurement confidence. Clear documentation and traceable identification for quality processes The item is supplied as a single test pin with clear identification (SKU: M323.248, GTIN available) to maintain traceability in quality records. Its workshop classification and compact footprint make it a straightforward addition to inspection kits and portable gauge sets. For companies implementing or maintaining statistical process control, the pin offers a stable physical reference that can be incorporated into regular calibration routines and inspection plans. For workshop‑grade precision from Metav IndustryLine, request the M323.248 gauge pin via Metav Werkzeuge or contact our inspection specialists at info@metav-werkzeuge.com to discuss suitability for specific measurement tasks. Technical Data Article number: M323.248 GTIN: 4061905055553 Manufacturer: Metav IndustryLine Facts Diameter: 2.48 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop execution Delivered in transport case Single test pin FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.248 is manufactured to a tolerance of ±0.001 mm, suitable for high‑precision end‑measure and bore checks. What materials is the pin made from? The pin is produced from special steel, selected for durability in workshop use while maintaining dimensional stability. How is the pin supplied for transport and storage? The test pin is supplied in a transport case to protect the measuring surface during handling and transit. Which applications is this pin intended for? Typical uses include fine bore verification, plug checks, reference measurements and integration into inspection fixtures and comparator setups. What identification is provided for traceability? The item is listed under SKU M323.248 with GTIN 4061905055553 for clear traceability in quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.49mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the proven combination of industrial robustness, micrometre-level precision and compact handling for reliable end measurements; the 2.49 mm diameter and ±0.001 mm tolerance ensure reproducible results in set‑up and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.249 — single gauge pin, 2.49 mm, ±0.001 mm (Metav IndustryLine) The M323.249 is a single gauge pin designed for precise end‑measurement and reference tasks in workshop environments. Diameter 2.49 mm precision Tolerance ±0.001 mm Length 50 mm workshop version Special steel construction Consistent micrometre precision for end measurements The compact diameter and tight tolerance deliver consistent results when checking final dimensions. With a certified accuracy of ±0.001 mm, the pin provides a defined reference for end‑measurements and quick verification steps. This level of precision reduces variability between successive checks and supports tighter process control in assembly and inspection workflows. The slim profile keeps insertion force low while maintaining contact stability for repeatable readings. Durable workshop construction that withstands daily use Built as a workshop execution item from special steel, this gauge pin balances hardness and wear resistance with manageable handling. At 50 mm length the pin offers a stable measuring element without excess overhang, assisting fast positioning in fixtures or bore checks. The compact mass contributes to simple handling during routine checks and minimises the risk of uncontrolled deformation during use, extending service life under typical shopfloor conditions. Integrates into quality control and setup procedures The pin complements standard gauge sets and serves as a reliable reference for end measurements and dimensional set‑up. Its straightforward geometry makes it suitable for jigs, alignment tasks and comparative checks where a defined diameter is required. Because the component is single and compact, it speeds up repetitive verification steps and supports a more efficient workflow, reducing idle machine time and improving throughput in small‑batch and repair environments. Plain data, clear traceability and practical handling The design emphasises measurable performance: 2.49 mm nominal diameter, ±0.001 mm declared accuracy and a 50 mm length make specification checks simple and verifiable. The robust finish and workshop format help keep maintenance minimal; common cleaning and visual inspection routines are sufficient to maintain performance. For customers requiring series matching or set configurations, the gauge pin serves as a precise building block within broader metrology equipment. For procurement or tailored advice on using Metav IndustryLine gauge pins such as the M323.249 in existing inspection routines, contact Metav Werkzeuge for immediate delivery and technical consultation Technical data Article number: M323.249 GTIN: 4061905055560 Label: Gauge pin, single, 2.49 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.49 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Material: Special steel Version: Workshop execution Intended application: End measurements FAQ What is this gauge pin used for? The M323.249 gauge pin is intended as a precise reference for end measurements, fixture set‑up and quick dimensional checks in workshop environments. What accuracy can be expected from the M323.249? Declared tolerance for the M323.249 is ±0.001 mm, allowing micrometre‑level repeatability for critical small‑diameter references. Which material is the pin made from? The pin is manufactured from special steel, chosen to offer a balance of wear resistance and stable dimensions under normal workshop conditions. How does the M323.249 help in day‑to‑day inspection tasks? As a compact and accurately dimensioned element, the M323.249 simplifies repetitive verification and alignment steps, improving throughput and reproducibility in routine quality control. Can the M323.249 be combined with other gauge sets? Yes, the single gauge pin integrates easily into existing gauge sets and fixture arrangements to provide a defined reference diameter for comparative and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.4mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of the combination of precision diameter 2.40 mm, ±0.001 mm tolerance and a sturdy workshop execution for reliable end‑size verification; the test pin is supplied in a protective transport case and can be ordered directly via Metav Werkzeuge or discussed with their consultants for application advice. Test Pin M323.240 — 2.40 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) The Test Pin M323.240 is a single precision gauge pin intended for end‑size inspection and repeatable go/no‑go checks in workshop environments Precision diameter 2.40 mm Tolerance ±0.001 mm Length 50 mm, workshop grade Supplied in protective transport case Consistent, reproducible end‑size verification for production control The compact gauge pin is designed for reproducible inspection, delivering the benefit of fast, repeatable checks on small bores and seating dimensions. With a diameter of 2.40 mm and a declared tolerance of ±0.001 mm, the pin enables confident decision‑making in quality control: a clear pass/fail result reduces interpretation variance and shortens inspection time. The tight tolerance supports processes where dimensional conformity is critical and where statistical control requires stable reference measurements. Workshop‑ready design that combines durability and handling Built as a workshop execution, this single test pin offers robustness for frequent use without compromising handling. The 50 mm length provides convenient reach and grip for routine checks while keeping the tool easy to manoeuvre. Supplied in a protective transport case, the gauge arrives ready for immediate use and secure storage; the compact weight of 0.005 kg makes it simple to add to an inspection kit or carry between stations without adding bulk. Material choice for dimensional stability under repeated use Manufactured from special steel, the pin balances strength and dimensional stability to withstand the mechanical demands of repeated insertion and withdrawal. The material selection reduces the risk of rapid wear, maintaining the specified diameter and tolerance over many cycles. For workshops and metrology benches that require dependable reference inserts, this construction translates into fewer tool changes and steadier process capability indices. Clear application focus and traceable identification Optimised for end‑size inspection, the pin is suitable for checking small bores, gauges and seating fits in mechanical assemblies and precision subcomponents. The product is identified by SKU M323.240 and GTIN for inventory control and traceability, supporting organised quality systems and record keeping. Where a compact, high‑precision reference is required, this gauge pin provides a practical, measurable solution that integrates with established inspection routines. Contact Metav Werkzeuge for technical guidance on integrating the M323.240 into existing inspection procedures and for fast delivery from Emmerich to the workshop bench Technical data SKU: M323.240 GTIN: 4061905054204 Brand: Metav IndustryLine Facts Diameter: 2.40 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Workshop execution Material: Special steel Supplied in protective transport case Use: End‑size inspection FAQ What is the intended use of this test pin? The test pin M323.240 is intended for end‑size inspection and repeatable go/no‑go checks on small bores and seating dimensions in workshop and production environments. Is a calibration certificate supplied with the gauge pin? No ISO 17025 calibration certificate is specified for this item; the product data does not indicate delivery with a calibration certificate. What material is the pin made from and how does that affect performance? The pin is made from special steel, which provides a balance of strength and dimensional stability suitable for repeated insertion cycles and routine inspection tasks. How is the test pin delivered and stored? The pin is supplied in a protective transport case suitable for workshop handling and secure storage, reducing handling damage during transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.5 mm Limit Gauge Plug, Wear Allowance On Go Side, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance to ensure dependable go/no-go checks in serial inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or request specialist advice for integration into existing inspection routines. Filetta Limit Gauge Pin — hardened steel, DIN 7162 Filetta Limit Gauge Pin designed for pass/fail checking of bores and inspection fixtures in industrial metrology Hardened steel construction to DIN 7162 Precision diameter 2.5 mm Wear allowance on the good side Compatible with go/no-go checking routines Reliable pass/fail checking for production control The limit gauge pin delivers a compact, unambiguous check for bore conformity using a simple go/no-go principle, minimising decision time on the shop floor. Manufactured to DIN 7162, the pin provides a clearly defined acceptance limit that supports reproducible inspections and consistent quality gates. The 2.5 mm diameter is specified to industry tolerances, enabling rapid visual and tactile confirmation without complex set‑ups. This direct verification method reduces downstream rework by catching out-of-tolerance parts at the earliest stage. Durability that reduces downtime and maintenance Constructed from hardened steel, the gauge pin resists wear in continuous use and preserves the inspection boundary over many cycles. The integrated wear allowance on the good side prolongs service life by permitting controlled dressing or replacement procedures while maintaining measurement integrity. Fewer replacements and predictable maintenance intervals lead to improved uptime in production lines and lower total cost of ownership. The robust material choice also supports use in regulated environments where repeatability matters. Simple integration into quality workflows and fixtures The pin is suited for fixtures, plug gauges and measuring rigs where straightforward verification is required. Its compact profile and standardised specification make stock management and fixture design straightforward, helping to keep inspection routines efficient. Clear identification (SKU MS911.161) and adherence to established norms aid traceability in quality records and simplify audits. The component is ideal for workshops and inspection stations seeking a pragmatic, standards-based tool to support routine quality control. Contact Metav Werkzeuge for tailored advice and to source the Filetta limit gauge pin (SKU MS911.161) directly from Emmerich — expert support for specification and delivery is available. Technical Data Article number: MS911.161 Manufacturer: Filetta Type: Limit gauge pin Diameter: 2.5 mm Standard: DIN 7162 Material: hardened steel Special note: wear allowance on the good side Facts Diameter: 2.5 mm Standard: DIN 7162 SKU: MS911.161 Special features Hardened steel construction Wear allowance of the good side Intended for go/no-go checking and plug gauge applications Category: gauges / measuring pins FAQ What material is the gauge pin made from? The Filetta limit gauge pin is manufactured from hardened steel, ensuring wear resistance and stable inspection boundaries (SKU MS911.161). Which standard applies to this gauge pin? Manufactured to DIN 7162, the component fulfils established requirements for limit gauges and supports clear pass/fail decisions. What does the wear allowance mean in practical terms? The wear allowance on the good side allows controlled use and maintenance so the gauge retains its acceptance limit for longer in serial inspections. Can this pin be used in fixture-based inspections? Yes, the pin is suitable for fixture and plug gauge applications where a defined go/no-go limit is required for bore checks. How is the size specified? The pin is specified with a diameter of 2.5 mm and supplied under SKU MS911.161 for unambiguous ordering and traceability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2.51mm Test Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
A compact workshop gauge pin with ±0.001 mm accuracy and 2.51 mm diameter provides highly repeatable end‑measure inspections and tight‑fit verification; its 50 mm length and hardened special‑steel construction ensure robust handling in daily metrology work. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed Gauge pin M323.251 — Metav IndustryLine test pin, Ø 2.51 mm, ±0.001 mm A gauge pin M323.251 designed for precise end‑measure checks and fit testing in workshop and inspection environments Ultra‑fine tolerance ±0.001 mm Diameter 2.51 mm for tight fits 50 mm length, workshop grade Hardened special steel construction Consistent pass/fail assessment with micrometre‑level tolerance This workshop‑grade pin is made for repeatable verification tasks where precision matters. The ±0.001 mm tolerance reduces uncertainty in fit and end‑measure checks, turning subjective gauging into objective data. Thanks to the 2.51 mm diameter and the straight, ground shaft, the pin seats reliably in bores and gauges, so measurement chains and go/no‑go workflows remain consistent over many cycles. The design supports quick interchange in fixtures and simplifies regular inspection routines. Robust design for everyday metrology use Constructed from special steel and finished for durability, the pin copes with frequent handling in production and workshop environments. The 50 mm length gives sufficient engagement for stable positioning while staying compact for tight setups. The material choice delivers wear resistance and dimensional stability, which translates to fewer replacements and lower downtime. Where rough handling and repeated seating are common, the hardened shaft preserves the calibrated geometry for longer service life. Practical handling and transport for the workshop Delivered in a protective plastic or wooden transport box, the pin arrives ready for safe storage and on‑the‑bench use. The compact packaging protects the ground surface and the tip geometry during transit and prevents accidental damage in tool drawers. Lightweight at approximately 5 g, the component integrates easily into gauge sets and trays without adding bulk, which keeps tool control and workplace organisation efficient. Integration into inspection routines and traceability Although compact, the pin suits standardised inspection procedures and can be included in master sets or calibration schedules. The exact diameter and tolerance support traceable checks and documented acceptance criteria in go/no‑go testing. For traceability and inventory management, the article is identified by its SKU and GTIN, making procurement and record‑keeping straightforward for quality departments and stores. Contact Metav Werkzeuge today for specification confirmation, delivery options and tailored batch quantities — Metav Werkzeuge can advise on compatibility with existing gauges and inspection workflows Technical data Article number: M323.251 GTIN: 4061905056239 Manufacturer: Metav IndustryLine Category: Gauge pin / Test pin Facts Diameter: 2.51 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop version Delivered in protective transport box FAQ What nominal size and tolerance does this gauge pin have? The gauge pin is manufactured to a nominal 2.51 mm diameter with a tolerance of ±0.001 mm, suitable for tight fit verification and end‑measure checks. Is the pin suitable for repeated seating in go/no‑go gauges? Yes; the hardened special steel construction and ground shaft are intended for frequent use in go/no‑go and fixture applications, maintaining geometry under typical workshop handling. How is the item identified for purchasing and inventory? This test pin is listed as SKU M323.251 and GTIN 4061905056239, which supports straightforward ordering and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.52mm Gauge Pin, Workshop Version, ±0.001mm, 50mm Length - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, sub‑micrometre tolerance and compact geometry for reliable end‑dimension verification; order the inspection pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.252 Gauge Pin – 2.52 mm, ±0.001 mm, 50 mm length by Metav IndustryLine The M323.252 is a single inspection pin designed for precise end‑dimension checks in workshop and inspection environments, ideal where compact, repeatable reference standards are required High precision ±0.001 mm tolerance Diameter 2.52 mm for end‑dimension verification 50 mm working length in special steel Consistent dimensional control for end measurements The compact inspection pin provides a dependable reference for end‑dimension and plug‑fit checks, allowing fast verification of small bores and mating parts. Manufactured from special steel, the pin combines surface stability with dimensional integrity, so routine checks run smoothly and reproducibly. The tight ±0.001 mm tolerance reduces ambiguity at the pass/fail threshold and supports tighter in‑process control, helping to cut rework and avoid production stoppages. Workshop robustness with easy handling A workshop‑oriented design balances stiffness and manageability: at 50 mm length the pin remains stable in hand and in fixtures, while the small diameter suits confined features typical of precision components. The single‑piece construction simplifies handling and storage and lends itself to quick gauging operations at assembly benches or inspection stations. This tangible ease of use speeds up inspection cycles without sacrificing measurement confidence. Traceable reference and application benefits As a purpose‑made inspection tool, the pin is intended for end‑dimension verification and component matching where tight clearances matter. The robust material choice supports repeated contact without rapid wear, maintaining the 2.52 mm nominal size over many cycles. Using defined reference pins like this one improves process reproducibility and supports quality assurance protocols in small‑part manufacture and finishing operations. Contact Metav Werkzeuge to discuss the M323.252 gauge pin for specific measurement tasks or to confirm suitability for production requirements — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.252 GTIN: 4061905056246 Category: Messstifte Facts Diameter: 2.52 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg eClass: 21170231 Special features Material: special steel Single inspection pin for end‑dimension checks Workshop execution suitable for routine gauging Intended for small‑bore and mating part verification FAQ What is the nominal diameter and tolerance of the inspection pin? The M323.252 inspection pin has a nominal diameter of 2.52 mm and a tolerance of ±0.001 mm, making it suitable for fine end‑dimension verification. Which applications suit this gauge pin? This gauge pin from Metav IndustryLine is designed for end‑dimension checks, small‑bore verification and component matching in workshop and inspection environments. What material is used and how does it affect wear? The M323.252 is made from special steel, chosen for surface stability and wear resistance so the pin maintains its dimensional integrity over repeated use. Is the pin supplied as a single item or in sets? The product is supplied as a single inspection pin, intended for individual reference use in fixtures or as a check standard. Can the pin be used for go/no‑go gauging or for reference measurement? Yes, the design and tight tolerance of the M323.252 make it suitable as a reference pin for go/no‑go checks and comparative measurements in quality control routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.53mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of workshop-ready precision and a compact form factor: the combination of a 2.53 mm diameter, an ultra-fine ±0.001 mm tolerance and a 50 mm length ensures consistent end‑dimension checks and fixture setting. Order this gauge pin directly via Metav Werkzeuge or consult the specialists if further clarification is required. Gauge pin M323.253 – 2.53 mm diameter, ±0.001 mm tolerance (50 mm length) | Metav IndustryLine A Gauge pin M323.253 designed for precise end‑dimension verification and accurate fixture alignment in workshop and inspection environments. High precision ±0.001 mm tolerance Diameter 2.53 mm for fine fits Length 50 mm, workshop version Delivered in protective box Repeatable micrometre‑level checks for quality control The central advantage of this gauge pin is its ±0.001 mm accuracy, which translates to repeatable, micrometre‑level measurements that are meaningful for tight tolerance work. With a nominal 2.53 mm diameter and a 50 mm active length, the pin functions as a reliable reference for go/no‑go checks, end‑dimension verification and plug‑fit testing. Precision at this scale reduces rework and secures downstream assembly quality, so measurement outcomes can be used directly in process control and documentation. Robust handling and workshop suitability Manufactured from special steel and supplied in a workshop version, the pin combines durability with straightforward handling. At just 0.005 kg the component is light enough for single‑handed positioning yet rigid enough to avoid deflection during insertion into gauges or fixtures. Delivery in a protective box protects the calibrated surface during transport and storage, preserving the measurement surface and ensuring consistent results across repeated use. The single‑piece supply supports traceability in inspection routines. Easy integration into metrology and fixture workflows As a simple, single gauge element, the M323.253 is ideal for setting up jigs, aligning fixtures and checking final bore dimensions where a precise reference pin is required. Its compact geometry makes it suitable for confined spaces and delicate assemblies while maintaining clear numeric specification for inspection protocols. Combined with Metav’s dependable supply chain and technical documentation, the pin supports efficient quality assurance routines and helps maintain production continuity without compromise. For workshop-ready precision and fast, reliable supply from Emmerich, contact Metav Werkzeuge for delivery options and technical advice on the M323.253 gauge pin. Technical data Article number: M323.253 GTIN: 4061905056253 Label: Gauge pin, single, 2.53 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Core specifications Diameter: 2.53 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.005 kg Materials & features Material: Special steel Workshop version Protective box for transport Single piece delivery FAQ What is the specified tolerance of the gauge pin? The gauge pin is manufactured with an accuracy of ±0.001 mm, providing micrometre‑level repeatability for inspection and fixture tasks. Which dimensions define the pin? The component has a 2.53 mm nominal diameter and a 50 mm length; these dimensions suit fine‑fit checks and end‑dimension verification. What material is used for the pin? The pin is made from special steel, selected for dimensional stability and workshop durability. Is the part supplied as a single item or in sets? This product is supplied as a single piece, packaged in a protective box for transport and storage. Can the pin be used for fixture setting and go/no‑go checks? Yes, the design and tolerance of this gauge pin make it well suited to fixture alignment and plug‑fit inspections in production and inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.54mm Gauge Pin, Single, ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
The combination of micrometre-level accuracy (±0.001 mm), robust special steel construction and compact 50 mm length ensures repeatable end‑measure checks in production. Order the pin directly via Metav Werkzeuge or consult the technical team for application advice. M323.254 Test pin — Gauge pin, 2.54 mm, ±0.001 mm (Metav IndustryLine) The M323.254 is a single gauge pin designed for precise end‑measure and assembly verification in workshop and inspection environments High precision ±0.001 mm Diameter 2.54 mm, length 50 mm Workshop‑grade special steel Single test pin for end‑measure checks Reliable micrometre‑level accuracy for production control Manufactured for tasks that demand minimal dimensional deviation, this gauge pin delivers ±0.001 mm accuracy, translating to consistent pass/fail decisions on tight fits and assembly tolerances. The defined diameter of 2.54 mm and compact 50 mm length make the pin suited to end‑measure checks, plug‑fit verification and small‑component gauging. Where reproducible measurement is essential, the narrow tolerance reduces rework and speeds up quality control cycles by providing an objective, verifiable reference. Durable workshop execution that withstands routine use The workshop‑grade construction and special steel composition combine wear resistance with dimensional stability so that the pin retains form under repeated handling. Surface condition and material choice minimise the risk of galling and preserve mating fits during inspection. For maintenance planning, the robust build reduces the need for frequent replacement, supporting predictable tool‑life and steady throughput in inspection benches and assembly stations. Practical fit‑check tool for inspection and assembly workflows Compact and straightforward to deploy, this single gauge pin integrates into go/no‑go checks, fixture validation and end‑of‑line sampling without complex setup. Traceability and clear specification allow integration into quality documentation and production records, while the small mass supports handheld use and rapid interchange in batch testing. The product’s precise specification assists calibration planning and simplifies comparison with CAD tolerances during design reviews. For secure supplies and expert guidance on integrating the Metav IndustryLine M323.254 into inspection routines, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss availability and technical matching. Technical data Article number: M323.254 GTIN: 4061905056260 Manufacturer: Metav IndustryLine Facts Diameter: 2.54 mm Length: 50 mm Accuracy/Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Version: Workshop execution Single test pin Category: Gauge pin (Messstifte) FAQ What tolerance can be expected from this gauge pin? The M323.254 test pin from Metav IndustryLine is specified at ±0.001 mm, providing micrometre‑level repeatability suitable for precise fit and end‑measure checks. Is this pin suitable for plug‑fit verification in assemblies? Yes; the 2.54 mm diameter and tight tolerance make the pin suitable for plug‑fit and end‑measure verification during assembly and inspection processes using the M323.254 gauge pin. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, chosen for durability and dimensional stability to minimise wear during repetitive inspection cycles. Can this pin be used for small‑component inspection in a workshop environment? Designed as a workshop‑grade test pin, the M323.254 is intended for routine inspection tasks, bench gauging and small‑component verification where compact, accurate references are required. How is the product identified for procurement and inventory? The product is listed as M323.254 with GTIN 4061905056260 to ensure clear identification in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.55mm Precision Probe ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from the combination of workshop‑grade construction, sub‑micron accuracy and compact dimensions for reliable end‑dimension checks. Take advantage of the precise diameter control and robust material to reduce scrap and inspection time. Order the inspection pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.255 — Inspection pin, Dia. 2.55 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.255 is a precision inspection pin designed for end‑dimension verification and go/no‑go checks in fine mechanical and workshop metrology. Workshop version for robust daily use Diameter 2.55 mm with ±0.001 mm tolerance 50 mm active length for deep checks Made from special steel for wear resistance Precision that minimises rework and inspection time The inspection pin delivers ±0.001 mm repeatability, a level of accuracy that supports tight end‑dimension control in serial checking and quality assurance. Manufactured to strict tolerances, the component reduces uncertainty in gauge stacks and plug tests, enabling faster go/no‑go decisions and fewer rejects. The combination of a precisely turned 2.55 mm diameter and a 50 mm length offers a reliable reference for small‑bore verification and end‑dimension measurement, translating directly into lower rework costs and improved process throughput. Tailored for micro‑range and fine mechanical tasks Classified for the micro range, this compact inspection pin suits tasks where minimal deflection and high positional accuracy are essential. Its dimensions make it particularly appropriate for small bores, connector pins and precision components found in watchmaking, instrumentation and miniature assemblies. The small footprint means handling is straightforward while maintaining stiffness at the contact point, so repeatable measurements are achievable even in confined setups. This focus on micro‑scale inspection supports consistent production quality where tolerances are measured in micrometres. Robust workshop design and material benefits The workshop version construction and special steel composition prioritise durability under frequent use. The material selection provides good wear resistance and dimensional stability, important for repeated insertion and extraction in production environments. A single‑piece design reduces potential error sources and eases traceability; the supplied unit is marked with the article identifier for inventory control. These factors combine to give a practical, long‑lasting inspection tool that integrates cleanly into existing bench equipment and inspection routines. For a precise match to production requirements and availability of Metav IndustryLine inspection tools, contact Metav Werkzeuge in Emmerich to discuss specifications and delivery options. Technical data Article number: M323.255 GTIN: 4061905056277 Category: Messstifte SKU: M323.255 Numbers / Core technical data Diameter: 2.55 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.005 kg Precision class: ±0.001 Special features Single inspection pin (einzeln) Workshop execution (Werkstatt‑Ausführung) Material: special steel Intended use: end‑dimension verification (endmasse) FAQ What applications is this inspection pin suited for? This inspection pin is ideal for end‑dimension checks, small‑bore verification and fine mechanical assemblies; the M323.255 from Metav IndustryLine is tailored to micro‑range inspection tasks. Is the tolerance of ±0.001 mm achievable in regular workshop conditions? Yes, when used with stable fixturing and consistent insertion force, the ±0.001 mm tolerance of the M323.255 can be realised, supporting reliable go/no‑go assessments and quality control. What material is used and how does it affect longevity? The inspection pin is made from special steel, chosen for wear resistance and dimensional stability under frequent use in workshop inspection routines. How is the pin identified for inventory and traceability? Each unit is supplied with the article identifier M323.255 and GTIN 4061905056277 to simplify stock management and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.56mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑grade test pin that combines ultra‑tight tolerance, robust special steel construction and a form factor made for repeatable end‑measure checks; order the item directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 2.56 mm, ±0.001 mm — 50 mm length (Metav IndustryLine) The Gauge pin, single, 2.56 mm, ±0.001 mm, length 50 mm is a workshop‑grade test pin for precise end‑measure inspections, plug and bore checking, and gauge setting in production and maintenance environments Workshop‑grade construction Diameter 2.56 mm ±0.001 mm 50 mm overall length for deep reaches Made from special steel Precision where small deviations matter Designed for applications that demand sub‑micrometre reliability, this compact test pin brings repeatable accuracy to routine checks. The diameter 2.56 mm combined with a tolerance of ±0.001 mm (one micrometre) ensures reliable fit‑up verification and end‑measure confirmation. In practice, that level of precision reduces setup time for inspection routines and lowers the risk of assembly rejects by providing a consistent physical reference for gauges and small bores. Robust build for workshop use and longevity Manufactured in special steel, the test pin resists wear and preserves the working diameter through repetitive use. The workshop‑grade execution prioritises handling and resilience over ultra‑fragile lab finishes, so the pin endures frequent insertion and removal in jigs, fixtures and inspection benches. The compact 50 mm shaft length balances reach and stiffness, keeping measurements steady without unnecessary flex. Efficient tool for quality control and gauge setting As a single gauge pin with a clearly defined nominal size and tolerance, this component streamlines go/no‑go workflows and manual gauge setting tasks. Where small bores or precise clearances are inspected, the pin serves as an objective reference that complements optical and dimensional checks. Its slim profile is ideal for confined geometries and end‑measure verification of small components, helping to accelerate routine checking and maintain consistent production quality. Contact Metav Werkzeuge for tailored advice and to reserve the workshop‑grade gauge pin M323.256 — call +49 2822 7131930 or eMail info@metav-werkzeuge.com to discuss compatibility and delivery options Technical data Article number: M323.256 GTIN: 4061905057144 Manufacturer: Metav IndustryLine Facts Nominal diameter: 2.56 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Workshop‑grade construction Material: special steel Intended use: end‑measure checks, plug and bore verification FAQ What is the nominal diameter and tolerance of this test pin? The gauge pin M323.256 has a nominal diameter of 2.56 mm with a tolerance of ±0.001 mm, making it suitable for high‑precision fit checks. Is this pin suitable for checking small bores and plug gauges? Yes. The M323.256 is designed as a single test pin for plug and bore verification and for setting mechanical gauges in workshop and production environments. What material is used for the pin? The M323.256 is manufactured from special steel, selected for wear resistance and dimensional stability under frequent use. How long is the pin and what reach does it provide? The overall length is 50 mm, which provides adequate reach for many confined geometries while maintaining stiffness for reproducible measurements. Can this component be used in assembly inspection to reduce rejects? Using the M323.256 as a defined physical reference for small clearances and end‑measure checks helps to standardise inspection results and can contribute to fewer assembly‑related rejects. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.57mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of absolute measurement precision, compact handling and workshop‑robust design for reliable end‑dimension checks; enquire with Metav Werkzeuge for matching sets or order the Test pin directly via Metav Werkzeuge. Test pin M323.257 — single gauge pin, 2.57 mm diameter, ±0.001 mm The Test pin M323.257 is a workshop‑grade gauge pin designed for high‑precision end‑measure verification and fixture alignment in fine mechanical applications. High‑precision Ø 2.57 mm ±0.001 mm Workshop‑grade special steel construction Compact 50 mm length for fixture and end‑measure Supplied in protective transport case Precision that secures process quality The production process benefits from a 2.57 mm diameter pin with an exceptional ±0.001 mm tolerance, delivering repeatable results when verifying final dimensions. Classified in the micro measurement range for compact instruments, this gauge pin is intended where minimal clearance and high reproducibility matter. Using a tight tolerance reduces rework and scrap rates, so inspection routines become a dependable part of the quality chain rather than a bottleneck. The compact geometry also minimises thermal and handling distortion during short‑cycle checks. Robust handling for busy workshops Built as a workshop‑grade component from special steel, the pin balances hardness with wear resistance to maintain dimensional integrity under routine use. With a length of 50 mm and a low mass (approx. 0.005 kg), the component is easy to position in jigs or fixture pockets while offering sufficient stiffness for manual placement. Supplied in a protective transport case, the pin arrives ready for immediate storage and safe transit between workstations, preserving the calibration state and surface finish important for accurate mating and alignment. Straightforward integration into inspection routines As a single, traceable gauge element, the pin is suited to end‑dimension checks, plug gauges and assembly alignment tasks where tight fits are required. Its compact size and workshop specification make it simple to include in existing gauge sets or to use as a reference for functional checks on small bores and pins. The straightforward design minimises ambiguity during inspection and speeds up operator training because the purpose and handling are immediately apparent. For series inspection, multiple identical pins can be ordered to establish fixtures with consistent reference points. For precise end‑measure verification or to configure a matched set from Metav IndustryLine, contact Metav Werkzeuge to secure the Test pin M323.257 or discuss technical matching options; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.257 GTIN: 4061905057366 Material: Special steel Length: 50 mm Diameter: 2.57 mm Accuracy: ±0.001 mm Weight: 0.005 kg Design: Workshop execution Facts Diameter: 2.57 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg GTIN: 4061905057366 Special features Workshop‑grade execution Supplied in protective transport case Single test pin for end‑measure verification Compact geometry for micro measurement range FAQ What material is the test pin made from? The Test pin M323.257 is manufactured from special steel designed for workshop use and wear resistance. Is the accuracy of ±0.001 mm suitable for fixture alignment? Yes, the ±0.001 mm tolerance of the Test pin M323.257 provides the precision required for demanding fixture alignment and end‑dimension checks. Does the pin come ready for transport or storage? The pin is supplied in a protective transport case to preserve surface integrity and dimensional accuracy during handling and transit. Can this pin be used for small bore checks and plug‑gage tasks? The compact 50 mm length and Ø 2.57 mm diameter make the Test pin M323.257 well suited to small bore checks, plug‑gage uses and mating‑part verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.58mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of micron-level accuracy and robust workshop design for reliable end-dimension checks; the compact diameter and 50 mm length ensure secure seating and repeatable results. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. M323.258 gauge pin – 2.58 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The gauge pin (2.58 mm, ±0.001 mm) is a single precision test pin intended as a reference for dimensional inspection and end‑dimension verification in workshop and inspection environments. 2.58 mm diameter with ±0.001 mm tolerance Length 50 mm for stable engagement Manufactured from high-grade special steel Supplied in protective case for transport Micron-level accuracy for dependable inspection results This workshop‑grade test pin delivers a ±0.001 mm tolerance, making it suitable where micrometre‑scale reproducibility is required. The extremely fine tolerance is a rational choice for precision jigs, go/no‑go checks and calibration routines where small deviations translate directly into production quality. By using a dedicated reference pin with a defined diameter of 2.58 mm, inspection processes become measurable and comparable, which reduces uncertainty and supports faster go/no‑go decisions on the shop floor. Durable construction and handling designed for everyday use Constructed from special steel, the pin combines surface integrity with a compact form factor to resist wear during repeated seating and withdrawal. A length of 50 mm ensures stable engagement in bores and fixtures, simplifying alignment and reducing handling variability. Delivered in a protective case for transport, the item arrives ready for safe storage and mobility between workstations; this practical packaging protects the pin during transit and will help preserve its measurement integrity over time. Practical integration into inspection workflows The M323.258 pin is designed to be a straightforward metrology companion that fits existing gauges, fixture sets and inspection routines. Its compact mass (approximately 0.005 kg) minimises disturbance during delicate placements and supports repeatable results in serial checks. Using a dedicated gauge pin shortens measurement time and diminishes rework through more consistent acceptance criteria — a clear efficiency argument for production and quality teams that prioritise throughput without compromising on tolerances. For availability and personalised application advice on Metav IndustryLine precision pins, contact Metav Werkzeuge in Emmerich for technical support and stock information Technical data Article number: M323.258 GTIN: 4061905057373 Manufacturer: Metav IndustryLine Weight: 0.005 kg Facts Diameter: 2.58 mm Tolerance: ±0.001 mm Length: 50 mm Special features Material: Special steel Workshop version Supplied in a protective case for transport Category: Gauge pins (Messstifte) Story trigger: end-dimension checks FAQ What level of accuracy can be expected from this gauge pin? The M323.258 gauge pin is specified with a tolerance of ±0.001 mm, suitable for micron‑sensitive inspection tasks and precision checks. Can the pin be used in production fixtures and jigs? Yes, the pin’s 2.58 mm diameter and 50 mm length provide stable seating for fixtures and jigs used in workshop inspection and alignment operations. What material is the pin made from and how does that affect durability? The pin is made from special steel, chosen for its robustness in workshop use and resistance to wear during repeated engagement. Is the pin supplied with any protective packaging? The product is supplied in a protective case for transport, which helps maintain measurement integrity when moving between workstations. Which applications suit this gauge pin best? Typical uses include end‑dimension verification, bore checks and reference measurements where a precise, single‑diameter gauge pin is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.59mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Combine submicrometre accuracy with a robust workshop design to speed up inspections and reduce rework; rely on the 2.59 mm diameter and ±0.001 mm tolerance for repeatable end‑measurements and order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.259 — 2.59 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.259 is a single inspection pin designed for precise end‑dimension checks in workshop and metrology environments, ideal where tight fits and repeatable go/no‑go tests are required. Diameter 2.59 mm precision pin Tolerance ±0.001 mm for tight fits 50 mm overall length for depth checks Made from special steel, workshop grade Precision that minimises rejects A tolerance of ±0.001 mm (1 µm) positions this inspection pin in the high‑precision class for dimensional control. The very fine tolerance ensures reliable verification of bore and shaft fits during incoming inspection and final assembly, translating into fewer rejects and less rework. By using a dedicated precision pin rather than improvised probes, measurement uncertainty is reduced and decision limits become more consistent, which supports production efficiency and traceable quality control. Robust workshop construction for everyday use Engineered as a workshop execution, the pin is manufactured from special steel to withstand repeated use under industrial conditions. The 50 mm overall length provides sufficient reach for depth checks while remaining compact for easy handling and fixture use. The combination of stable material and compact geometry preserves roundness and dimensional stability over time, so maintenance intervals are extended and repeatability is maintained across inspection routines. Practical inspection workflow and compatibility Supplied as a single item, this gauge pin is aimed at bench inspection, fixture verification and go/no‑go testing of critical end measurements. The 2.59 mm diameter is suited to fine tolerances and small bores where accurate end measurements are decisive for assembly quality. Integrating the pin into existing inspection gauges or depth checks is straightforward and supports faster throughput by simplifying the verification step: a quick physical check replaces lengthy adjustment cycles and contributes to a smoother production flow. The compact weight also favours handheld checks and rapid fixture changes. Contact Metav Werkzeuge GmbH for specialist advice from Emmerich and to discuss how the M323.259 can be integrated into existing inspection routines Technical data Article number: M323.259 GTIN: 4061905057380 Material: Special steel Tolerance: ±0.001 mm Length: 50 mm Data Diameter: 2.59 mm Length: 50 mm Weight: 0.005 kg Tolerance: ±0.001 mm Special features Workshop execution Single item supply Category: Gauge pins (Messstifte) ECLASS: 21170231 Story trigger: end measurements FAQ What is the dimensional tolerance of this inspection pin? The M323.259 gauge pin is specified with a tolerance of ±0.001 mm, providing micron‑level control for precision fits. Is the pin suitable for depth and end‑face measurements? Yes — the 50 mm overall length makes this gauge pin suitable for depth checks and end‑measurement tasks in fixtures and bench inspections. What material is used for the pin and why does it matter? The pin is made from special steel, selected for dimensional stability and wear resistance so that measurement accuracy remains consistent under workshop conditions. How is the gauge pin supplied and intended to be used? The item is supplied individually as a single inspection pin, intended for direct use in go/no‑go checks, fixture verification or handheld dimensional checks. Which applications benefit most from this pin? Applications with tight bore tolerances, precision assemblies and end‑measurement controls benefit most; the pin supports repeated, repeatable checks that reduce rework. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.5mm Limit Go Gauge With Wear Allowance, Hardened Steel DIN 7162 - Filetta
Take advantage of the combination of DIN 7162 conformity, hardened-steel durability and exact 2.5 mm tolerance control for reliable go/no‑go checking in batch inspection. Order the Filetta limit gauge pins directly via Metav Werkzeuge or consult our specialists for batch supply and enquiries. Grenzlehrdorne — limit gauge pin, 2.5 mm, hardened steel (Filetta) A Grenzlehrdorn by Filetta designed for precision go/no‑go verification and wear‑compensated accept/reject checks in production and inspection environments. 2.5 mm diameter, high repeatability Hardened steel construction for long life Conforms to DIN 7162 standard Wear allowance on the good side Consistent go/no‑go control to speed up inspection The Filetta limit gauge pin offers a compact solution for rapid acceptance testing where dimensional conformity must be checked repeatedly. Manufactured from hardened steel, the pin retains its geometry under frequent use, reducing downtime caused by damaged or worn gauges. The specification to DIN 7162 ensures compatibility with established inspection procedures and simplifies documentation within quality systems. The compact form factor and clear acceptance boundary make the item particularly suitable for small‑part assemblies where a fast pass/fail decision avoids lengthy measuring operations. Durable construction that reduces recalibration frequency Robust material selection and heat treatment give the gauge pin a service life that keeps maintenance intervals low. The hardened surface resists deformation, helping maintain the defined tolerance of 2.5 mm over many cycles. In addition, the built‑in wear allowance on the good side provides an engineered margin so that the gauge indicates wear before part acceptance is compromised. This design choice translates into lower lifecycle costs and fewer process interruptions, supporting steady production throughput and reliable quality control. Integrates with workshop routines and quality documentation Designed as a practical shop tool, the limit gauge pin supports streamlined inspection workflows and clear go/no‑go decisions at the point of assembly or incoming inspection. The simple physical check complements dimensional measurement equipment and is ideal for quick checks on batches or random samples. The product is supplied under the Filetta brand and can be adopted easily into existing inspection plans; traceability is maintained through the SKU MS911.203 for ordering and stock control. The result is a pragmatic balance between measurement certainty and operational efficiency. Contact Metav Werkzeuge for Filetta limit gauge pins (SKU MS911.203) to arrange a batch supply or technical briefing near Emmerich — our specialists will advise on quantities and integration into inspection plans. Technical Data Article number: MS911.203 Product name: Grenzlehrdorne Manufacturer: Filetta Material: gehärterter Stahl Standard: DIN 7162 Facts Diameter: 2.5 mm SKU: MS911.203 Special features Abnutzungsaufmaß der Gutseite (wear allowance on the good side) Intended for go/no‑go verification and pin gauge checks Category: Gauge pins / measuring pins FAQ What is the primary use of these limit gauge pins? The Filetta Grenzlehrdorne are intended for rapid go/no‑go checks and dimensional acceptance testing in production and inspection, providing a quick physical decision on part conformity. Is the material suitable for high‑frequency shop use? Yes; the pins are made from hardened steel, which offers resistance to wear and deformation under frequent use, ensuring consistent pass/fail performance. Does this pin comply with recognised standards? The limit gauge pin conforms to DIN 7162, making it suitable for integration into standardised inspection procedures and quality documentation. How does the wear allowance affect inspection results? The built‑in wear allowance on the good side gives an engineered margin that signals wear before a pin accepts out‑of‑tolerance parts, thereby safeguarding process quality. How can this item be ordered or specified for stock? Order by SKU MS911.203 (Filetta) via Metav Werkzeuge for reliable supply and support with integration into inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2.5mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade accuracy and robust workshop design for reliable end‑measurement in fixture and gauge production; the fine ±0.001 mm tolerance and slim 2.50 mm diameter ensure repeatable results and fast inspection cycles. Order the test pin directly via Metav Werkzeuge or contact their consultants for specification support. Test pin M323.250 — inspection pin, 2.50 mm diameter, ±0.001 mm (Metav IndustryLine) A single test pin, the M323.250, for precise end‑dimension checks and gauge fixtures in workshop metrology. Workshop design for rugged use Diameter 2.50 mm with ±0.001 mm tolerance 50 mm length suited to end‑dimension checks Made from special steel for long service life Consistent, measurable accuracy for routine inspection A compact inspection pin with a 2.50 mm diameter and ±0.001 mm tolerance delivers measurable improvements in process control. The narrow tolerance band permits reliable detection of micrometre‑level deviations during plug and gauge checks, which translates into fewer false rejects and more consistent lot acceptance. Where repeatability is critical, the controlled geometry and tight tolerance reduce uncertainty in comparative measurements and support efficient quality decisions. Built for workshop use and repeated handling The workshop design prioritises durability without compromising precision. Manufactured from special steel, the pin resists wear under frequent contact and maintains dimensional stability across repeated cycles. Supplied in a protective case for secure transport and storage, the test pin is ready for daily use at the inspection bench or as part of a gauge set. The robust finish and compact form factor keep maintenance intervals long and handling straightforward. Streamlined integration into inspection workflows This inspection pin suits end‑dimension verification and gauge fixtures where small‑diameter probes are required. The simple geometry makes the pin easy to seat in holders, mandrels or comparator fixtures, speeding up setup times and lowering per‑check overhead. Using standard identifiers such as SKU M323.250 and GTIN 4061905056222 helps with inventory control and traceability in production environments, supporting lean workflows and audit preparedness. Supports traceable quality processes and documentation Although supplied as a workshop tool, the component is designed to fit into documented quality systems. The material choice and tight tolerance facilitate reproducible measurements within established traceability chains; calibration to specific standards can be organised through usual metrology services if required. The combination of small form factor and high reproducibility makes the pin suitable for routines that demand both speed and documented measurement confidence. For precise end‑measurement components, request the Metav IndustryLine test pin M323.250 from Metav Werkzeuge — technical advice and order handling are available from Metav Werkzeuge at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.250 GTIN: 4061905056222 Manufacturer: Metav IndustryLine Material: special steel Length: 50 mm Diameter: 2.50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Design: workshop version Delivery: supplied in protective case Numbers / Core technical data Diameter: 2.50 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Measuring range: 2.5 mm Special features / Versions Workshop construction for daily use Special steel for wear resistance Supplied in protective plastic or wooden case GTIN and SKU for traceability FAQ What applications is this test pin suitable for? The test pin M323.250 is intended for end‑dimension checks, plug‑gauge inserts and small‑bore inspections where a 2.50 mm reference probe with ±0.001 mm tolerance is required. Is the material corrosion‑resistant? The M323.250 is made from special steel selected for durability; surface condition and environmental exposure determine long‑term corrosion behaviour and should be considered when storing or using the pin. Can this pin be fitted into standard gauge holders? Yes, the simple cylindrical geometry of the inspection pin suits standard holders and mandrels used in gauge sets and comparator fixtures, facilitating quick integration into existing inspection rigs. Does the product come with a calibration certificate? The standard supply is the workshop version of the inspection pin; calibration to specific standards can be arranged through usual metrology services if a traceable certificate is required for the M323.250. How is the test pin supplied for transport and storage? The test pin is supplied in a protective case to safeguard the measuring surface during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.61mm Test Pin Single ±0.001mm 50mm Workshop Finish - Metav IndustryLine
The combination of ±0.001 mm accuracy, a 2.61 mm diameter and a 50 mm length provides reliable end‑dimension control and reduced scrap in repetitive checks — order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.261 — single precision gauge pin, 2.61 mm, ±0.001 mm, 50 mm Gauge pin M323.261 is a single‑piece measuring pin designed for precise end‑measurement tasks in workshop environments and fixture set‑up Single gauge pin, 2.61 mm diameter Tolerance ±0.001 mm high precision 50 mm length for end measurement tasks Workshop version, robust workmanship Precision that reduces inspection uncertainty The M323.261 gauge pin delivers ±0.001 mm repeatability, making it suitable where tight dimensional control is required. Such fine tolerance significantly lowers the risk of false rejects and rework when used for end‑dimension checks or in assembly gauges. The close tolerance is achieved through controlled material selection and finish, which ensures consistent contact geometry; this reduces measurement scatter and supports reliable go/no‑go verifications and transfer measurements in serial inspection. Durable construction for daily workshop use Manufactured from special steel, the pin is engineered for repeated seating and withdrawal in hardened bushings and fixtures. The 50 mm shaft length combined with the 2.61 mm diameter offers a favourable stiffness-to-length ratio for end‑measure applications, improving handling stability compared with shorter or thinner pins. The workshop version designation reflects a focus on robustness and straightforward integration into everyday tooling — less downtime for replacement and consistent fit in gauges or locating plates. Practical application: where this pin adds value Used individually as a reference or locating element, the pin is ideal for end‑measure tasks, setting up jigs and verifying mating bores. Its single‑piece design simplifies stockkeeping and replacement in repair situations. Where equipment or fixtures require a precise datum pin for repetitive positioning, the combination of tight tolerance and durable material reduces variation between cycles and streamlines quality control routines. The pin supports efficient measurement workflows and contributes to reproducible assembly and testing processes. Contact Metav Werkzeuge for availability and tailored advice on integrating this precision gauge pin into existing fixtures or inspection routines Technical data Article number: M323.261 GTIN: 4061905057403 Manufacturer: Metav IndustryLine Facts Diameter: 2.61 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Delivery form: single piece Intended use: end‑measurement / locating tasks Version: workshop execution FAQ What is the intended application for this gauge pin? This gauge pin is intended for end‑measurement, locating and fixture work where a precise reference pin with ±0.001 mm tolerance is required. Is the material suitable for repeated seating in hardened bores? Yes, the pin is made of special steel designed for robust workshop use and repeated engagement in hardened bushings and locating holes. How does the 50 mm length affect handling and stiffness? A 50 mm shaft provides a good balance between reach and rigidity for end measurements; the 2.61 mm diameter helps keep deflection low for reliable positioning. Can this pin be used as a reference in assembly jigs? The single‑piece construction and tight tolerance make it suitable as a datum or locating element in assembly jigs and inspection fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com