Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
2.86mm Gauge Pin, ±0.001 mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, sub‑micrometre tolerance and a compact 50 mm length for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.286 Gauge pin — 2.86 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.286 gauge pin is a workshop‑grade measuring pin designed for precise end‑measurements and fixture alignment in machining and quality‑control environments. Workshop-grade precision measuring pin Diameter 2.86 mm with ±0.001 mm tolerance 50 mm hardened special-steel shaft Single-piece design for end-measure checks Precision engineered for critical end‑measurements This gauge pin delivers ±0.001 mm nominal runout tolerance on a 2.86 mm diameter, providing the kind of repeatable accuracy required for final dimension verification and reference checks. The compact geometry keeps bending moments low, which improves measurement repeatability when used as an end‑stop or reference dowel in fixture and gauge setups. In practice, the fine tolerance reduces rework and supports reliable pass/fail decisions in small‑part production. Durable shaft and simple handling for the workshop Manufactured from special steel and finished for workshop use, the pin’s 50 mm length balances reach with rigidity, helping to avoid flex under normal handling. The single‑piece design minimises joints and potential misalignment, so the component is easy to seat in bores or plates and is robust against routine handling. This construction supports longer service life and consistent contact geometry for tactile or optical inspection methods. Fits into inspection routines and fixture alignment The measuring pin suits a range of inspection and set‑up roles, from pinning components during assembly to acting as reference dowels in jigs and gauges. Its small diameter and tight tolerance make it particularly suitable for end‑measure checks and checking end dimensions on turned parts. When incorporated into a measurement routine, the pin improves fixture alignment and reduces set‑up variability, which in turn shortens cycle times for recurring inspection tasks. Practical benefits for production quality and traceability Using a precision gauge pin with sub‑micrometre tolerance enhances traceability and supports consistent quality outcomes. The part’s straightforward geometry keeps measurement uncertainty low and simplifies documentation of inspection steps. For workshops seeking to standardise inspection aids, this component reduces variability between operators and contributes to a verifiable measurement process that integrates smoothly with existing quality workflows. Contact Metav Werkzeuge for expert advice on using the M323.286 gauge pin in fixtures and inspection routines — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability. Technical data Article number: M323.286 GTIN: 4061905057229 Manufacturer: Metav IndustryLine Category: Gauge pins / Measuring pins Measurements Diameter: 2.86 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Materials & features Material: special steel Version: workshop execution Single‑piece design Suitable for end‑measure checks and fixture alignment FAQ What accuracy can be expected from this gauge pin? The M323.286 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, making it suitable for fine end‑measure verifications in workshop and inspection applications. Which materials is the pin suitable for during use? As a measuring aid, the gauge pin is a hard special steel component intended to contact workpieces of various materials; it serves as a reference element rather than a cutting tool. Can the pin be used for fixture alignment and jigs? Yes, the M323.286 is designed for fixture alignment and indexing tasks, where its small diameter and tight tolerance help ensure reproducible positioning. How should the pin be handled to preserve accuracy? Handle the gauge pin with clean gloves or a cloth to avoid contamination and avoid dropping; seating into accurately drilled holes or hardened bushings will preserve the measurement geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.87mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Reliable measurement of end dimensions is achieved with a compact, workshop-grade gauge pin that combines a 2.87 mm diameter with an ultra-fine ±0.001 mm tolerance and a 50 mm length; benefit from precise, repeatable checks and robust handling for production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.287 Gauge pin (single) — 2.87 mm Ø, ±0.001 mm A gauge pin designed for end-dimension inspection and workshop verification, supplied in a compact format for precise checking of fits and bore gauges. Workshop-grade precision ±0.001 mm Diameter 2.87 mm for fine tolerances Length 50 mm for compact handling Supplied in protective transport case Precision for end-dimension inspection An inspection pin with ±0.001 mm tolerance provides the confidence required in high-precision checks. The extremely fine tolerance reduces measurement uncertainty when validating end dimensions or verifying bore fits, so production decisions rest on verifiable data rather than estimates. The 2.87 mm diameter is suited to small-bore checks and close-tolerance assemblies, enabling reliable pass/fail decisions in quality control. Durable construction optimised for workshop use Constructed from special steel, this workshop version is engineered for frequent handling and repeat operations. The 50 mm length balances reach with rigidity, limiting deflection during insertion and withdrawal. Hardened surfaces and a smooth finish sustain dimensional stability over repeated cycles, which reduces rework and downtime by maintaining consistent inspection points in everyday workshop routines. Efficient integration into inspection workflows Compact geometry and defined dimensions simplify use with existing fixtures and gauge blocks. The pin is particularly useful for end-measurement setups and reference checks during incoming inspection or assembly verification. Traceable identification (SKU M323.287) and straightforward compatibility with standard gauge fixtures speed up process implementation and support lean inspection cycles on the shop floor. For workshop-grade inspection tools and local supply, contact Metav Werkzeuge in Emmerich for advice and procurement assistance to ensure the right gauge pin arrives where it is needed. Technical data Article number: M323.287 GTIN: 4061905057847 Description: Gauge pin, single, 2.87 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.87 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Material: special steel Workshop version Designed for end-dimension inspection Supplied in protective transport case FAQ What does the ±0.001 mm tolerance mean in practice? The tolerance indicates the gauge pin is manufactured to within ±0.001 mm of the nominal 2.87 mm diameter, ensuring highly consistent measurements when using the M323.287 gauge pin for end-dimension or bore checks. Is this pin suitable for repeated workshop use? Yes; the workshop-grade construction and special steel material make the M323.287 resilient to frequent handling and routine inspection tasks. Which inspection tasks is this gauge pin best for? It is optimised for end-dimension verification, small-bore gauging and reference checks where a compact 50 mm length and a 2.87 mm diameter are required. Can the pin be used with standard gauge blocks and fixtures? Yes; the defined dimensions and compact length allow straightforward integration into common gauge setups and fixture-based verification procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.88mm Gauge Pin, Workshop Version, ±0.001mm, Length 50mm - Metav IndustryLine
Take advantage of the combination of 1 µm accuracy, compact dimensions and robust workshop design for consistent end‑dimension checks and fixture setup. Order the M323.288 gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.288 gauge pin — Ø 2.88 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.288 is a workshop‑grade gauge pin intended for precise end‑dimension checks, fixture alignment and verification tasks in metrology environments. Diameter 2.88 mm for tight fits Tolerance ±0.001 mm for 1 µm accuracy Length 50 mm for deeper reference points Workshop version with robust finish Reliable micrometre‑level reference for critical checks This gauge pin delivers repeatable measurements thanks to a specified tolerance of ±0.001 mm, equivalent to 1 µm. Such precision supports quality control tasks where small dimensional deviations are consequential, for example final bore checks or plug gauging of mating parts. The defined diameter of 2.88 mm and the 50 mm shank create a stable contact geometry that reduces angular error during insertion, enabling faster go/no‑go assessments and fewer reworked parts. Emphasis is placed on measurable performance and demonstrable conformity rather than subjective claims. Durable construction suited to workshop routines Manufactured from special steel, the pin is designed to withstand repeated use in inspection areas and jigs. The chosen material provides dimensional stability and resistance to routine wear typical in busy workshop settings, maintaining reference integrity over many cycles. At a mass of 0.006 kg the part is light to handle yet stiff enough to resist bending in standard applications. The workshop specification highlights practical longevity and straightforward handling for technicians performing frequent checks. Integrates with inspection workflows and fixture setup The pin functions as a compact reference for end‑dimension measurement, alignment of fixtures and verification of mating bores. Its compact form factor and defined geometry simplify storage and deployment in inspection benches or gauge sets. When incorporated into a systematic QC routine, the component reduces cycle time for quick checks and complements gauge blocks or plug gauges for traceable results. Supplied as a single item with clear identification, it supports orderly inventory management and straightforward replacement planning. For procurement, technical clarification or to source the M323.288 gauge pin from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for direct advice and reliable supply. Technical Data Article number: M323.288 GTIN: 4061905057854 eClass: 21170231 Label: Prüfstift, einzeln, 2,88mm, +/- 0.001 mm Länge 50 mm Numbers / Core technical data Diameter: 2.88 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features / Versions Material: Special steel Version: Workshop specification Category: Gauge pin (Messstifte) SKU: M323.288 FAQ What tolerance does this gauge pin offer? The M323.288 gauge pin is specified with a tolerance of ±0.001 mm, providing 1 µm accuracy for critical dimensional checks. For which tasks is this gauge pin suitable? This gauge pin is intended for end‑dimension verification, fixture alignment and plug gauging tasks in workshop and inspection environments. What material is used for the pin? The pin is made from special steel, chosen for dimensional stability and wear resistance appropriate to routine inspection use. How is the M323.288 supplied? The item is supplied as a single gauge pin, clearly identified by SKU M323.288 and GTIN 4061905057854 for inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.89mm Test Pin, ±0.001 mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometric tolerance, compact design and workshop‑grade steel for reliable end‑measure checks; order the part directly via Metav Werkzeuge or contact the consultants for application advice. Gauge pin M323.289 — precision test pin, Ø 2.89 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The Gauge pin M323.289 is a precision test pin for end‑measure and fit verification in workshop inspection and assembly tasks Workshop version, robust design Diameter 2.89 mm for precise fits Tolerance ±0.001 mm for micrometre accuracy Delivered in protective transport box Ensure repeatable fits and fast verification The straight, hardened gauge pin provides a defined reference for quick go/no‑go checks and dimensional verification where repeatability matters. With a nominal diameter of 2.89 mm and an accuracy of ±0.001 mm, the pin is designed to reduce uncertainty during short series inspections and setup operations. The slim geometry makes it particularly suitable for checking small bores, pin holes and end‑masses, enabling efficient quality control without time‑consuming measurement chains. The compact form reduces the influence of handling during short inspections, supporting more consistent results in routine use. Built for workshop use and daily handling Manufactured from special steel and specified as a workshop version, the pin withstands frequent handling and maintains dimensional stability under normal workshop conditions. The 50 mm length gives sufficient engagement for most pin‑fit checks while remaining easy to manipulate with one hand or a simple holder. The robust finish and material selection prioritise longevity: the pin resists routine knocks and small abrasions that occur during setup and assembly work, which lowers replacement frequency and supports steady production throughput. Practical storage and transport for traceable parts Delivered in a protective box for transport, the pin arrives ready for safe storage and clear identification on the shop floor. The packaging minimises the risk of damage between uses and keeps the reference surface clean for precise fitting. For traceability and inventory control, the article is supplied with the manufacturer SKU and GTIN, which eases integration into tool boards and inspection logs. This practical approach reduces downtime and supports a structured inspection routine in small to mid‑sized production environments. For secure procurement of this Metav IndustryLine gauge pin and tailored advice on fit‑checking workflows, contact Metav Werkzeuge GmbH — they will assist with technical details and supply options Technical data Article number: M323.289 GTIN: 4061905057861 Brand: Metav IndustryLine Label: Gauge pin, single, 2.89 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.89 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: special steel Workshop execution Delivery in protective transport box Suitable for end‑measure checks FAQ What is the intended use of this gauge pin? The gauge pin M323.289 is intended for end‑measure checks and fit verification of small bores and locating features in workshop and inspection tasks. How precise is the M323.289 during routine checks? The M323.289 offers an accuracy of ±0.001 mm, providing micrometre‑level precision for consistent go/no‑go and fit assessments. Which material is the pin made from and why does it matter? This gauge pin is made from special steel to ensure wear resistance and dimensional stability under frequent handling in workshop environments. Is the pin supplied ready for use and how is it packaged? The product is supplied as a single gauge pin and is delivered in a protective transport box to preserve the measuring surfaces during storage and transit. Can this pin be used for traceable inventory or inspection systems? Yes, the M323.289 is identified by SKU and GTIN for easy integration into tool control and inspection traceability systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.8mm Test Pin, 50mm Length, ±0.001mm Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of 2.80 mm diameter, ultra‑tight ±0.001 mm tolerance and a robust 50 mm length for precise end‑measure checks and reliable repeatability in production. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.280 — 2.80 mm precision inspection pin, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.280 designed for exact end‑measurement and fit checks in workshop inspection and fixture testing. 2.80 mm diameter for tight tolerances Tolerance ±0.001 mm for high repeatability 50 mm length for deeper engagement Workshop version with transport box Precision that reduces rejects and speeds inspection The small diameter and fine tolerance of this inspection pin deliver measurable advantages on the shop floor. With a 2.80 mm diameter and an accuracy of ±0.001 mm, the pin supports repeatable fit and alignment checks that reduce measurement uncertainty and lower scrap rates. In practice such a narrow tolerance simplifies pass/fail decisions and shortens inspection cycles, because interchangeability and clear go/no‑go outcomes are easier to verify. The design suits use in comparative gauges, fixture checks and manual measurement rigs where consistent dimensional control is essential. Robust material and design for everyday workshop use Manufactured from special steel and specified as a workshop version, this measuring pin balances corrosion resistance and mechanical robustness for routine handling. The single‑piece construction and the choice of material improve wear resistance, which maintains gauge life and measurement stability over many cycles. Supplied as an individual unit and protected for shipment in a dedicated box for transport, the component arrives ready for immediate integration in inspection tools or storage without additional packaging work. Practical applications and integration into quality workflows The inspection pin functions as a precise end‑measure element for alignment, plug‑gauge checks and assembly verification on small bore parts. Its 50 mm length gives sufficient engagement for many internal checks while remaining compact enough for tight fixtures. The light mass makes handling straightforward and reduces distortion risks during manual placement. As a standardised, high‑precision measuring element from Metav IndustryLine, the pin is suitable for production sampling, first‑article inspection and retrofitting into custom gauges where a defined diameter and sub‑micrometre repeatability improve process capability. For precision checks with the ±0.001 mm inspection pin, contact Metav Werkzeuge for sample availability or tailored advice — Metav Werkzeuge GmbH can be reached at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.280 GTIN: 4061905056802 Manufacturer: Metav IndustryLine Facts Diameter: 2.80 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Material: Special steel Configuration: Single gauge pin for inspection use Version: Workshop execution Packaging: Supplied in a transport box FAQ What materials is this inspection pin made from? The inspection pin is made from special steel, specified in the technical data to provide durability and wear resistance for workshop use. Is the tolerance of ±0.001 mm suitable for assembly checks? Yes, the ±0.001 mm tolerance of the inspection pin supports high‑precision assembly and plug‑gauge checks where tight fits and repeatable results are required. Can the pin be used in custom fixture gauges? The M323.280 inspection pin is designed for integration into gauges and fixtures; its 50 mm length and standard diameter make it suitable for many bespoke inspection setups. How is the pin delivered and stored? The component is supplied as a single unit and packaged in a transport box to protect the surface and maintain measurement integrity during storage and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.90mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Combine workshop-grade robustness, ultra-fine ±0.001 mm tolerance and compact geometry (Ø 2.90 mm, length 50 mm) for consistent end-measurements and reliable go/no-go checks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Test Pin M323.290 — Gauge pin, Ø 2.90 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) Test Pin M323.290 is a single, high-precision gauge pin designed for end-measurement and dimensional verification in workshop and inspection contexts, offering a compact form factor for confined applications High accuracy ±0.001 mm Diameter 2.90 mm, length 50 mm Special steel construction Delivered in protective box Precision where measurements must not fail The M323.290 is engineered to deliver consistent results in routine inspection and assembly tasks. With a verified tolerance of ±0.001 mm, the pin reduces measurement uncertainty and supports repeatable checks on small bores and indexed features. The compact Ø 2.90 mm dimension and 50 mm shank length make it particularly suitable for confined or hard‑to‑reach locations where stability and exact fit matter. The solid construction provides predictable contact geometry, which helps to maintain measurement traceability in quality control sequences. Built for workshop resilience and straightforward handling Designed as a workshop execution, this gauge pin combines durability with simple handling to keep throughput high. Manufactured from special steel, it resists routine wear while remaining light enough for rapid operator use—the listed mass is approximately 0.006 kg, which supports fast interchange without fatigue. Supplied in a protective box, the component arrives ready for safe storage and transport, reducing the risk of incidental damage and saving time in busy production environments. Easy integration into inspection workflows The single-piece format of this gauge pin suits a variety of metrology and assembly processes, from manual plug checks to use as a reference in jigs and fixtures. Labelling and traceable identifiers simplify inventory and audit procedures; the compact geometry supports modular fixture design and minimises downstream adjustment. For teams standardising inspection equipment, the consistent contact surface and tight tolerance contribute to shorter set-up times and fewer rejected parts, enhancing overall process efficiency. For workshop-grade gauge pins from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for application guidance or to secure stock — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.290 GTIN: 4061905057878 Brand: Metav IndustryLine EClass: 21170231 Facts Diameter: 2.90 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Measurement range (nominal): 2.9 mm Special features Special steel material Workshop execution Single piece delivery Supplied in protective transport box FAQ What tolerance does the gauge pin provide? The Test Pin M323.290 is specified with a tolerance of ±0.001 mm to support high‑precision end measurements. Which material is used for this pin? This gauge pin is made from special steel, chosen for wear resistance and dimensional stability in workshop use. Is the pin suitable for confined bores and fine features? Yes, the Ø 2.90 mm diameter and 50 mm length of the M323.290 are suited to confined bores and precise fit checks. How is the product delivered for safe handling? The M323.290 is supplied in a protective transport box to prevent damage during storage and transit. Can the pin be used in fixtures and jigs? The single-piece format and stable contact geometry allow the Test Pin M323.290 to be integrated into fixtures, jigs and manual inspection routines Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.91mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of precise diameter control and shop-floor robustness for reliable end‑measurement checks; combine the 2.91 mm nominal size with a ±0.001 mm tolerance and 50 mm length to ensure repeatable gauging in fixtures and inspection routines — order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin M323.291 — 2.91 mm diameter, ±0.001 mm tolerance A gauge pin M323.291 designed for precision end measurements and fixture verification in workshop and inspection environments. Diameter 2.91 mm, high-precision fit Tolerance ±0.001 mm for repeatable checks Length 50 mm for fixture compatibility Workshop version, robust finish Keep production accurate with measurable precision The primary advantage of this single gauge pin is its tight nominal control: a 2.91 mm diameter manufactured to ±0.001 mm guarantees dimensional consistency for small-bore checks and plug-fitting tasks. Such precision reduces ambiguity in pass/fail decisions during incoming inspection and in-process checks, so measurement results can be relied on when recording tolerances or adjusting fixtures. The narrow tolerance also shortens decision times on the shop floor and supports traceable quality control when repeatability matters. Robust shop-floor design reduces handling risks Specified as a Workshop version, the pin combines a compact form with a finish and material choice suited to everyday use. Manufactured from special steel, the pin offers corrosion resistance and wear performance appropriate for regular insertion into bores and jigs without rapid surface degradation. The 50 mm shank gives sufficient engagement for many fixture geometries while remaining easy to handle and position with standard tweezers or collet holders. The result is sustained service life and fewer replacements — an efficiency gain in both routine metrology and fixture verification. Practical integration into inspection workflows Small components, gauges and end-measure parts demand straightforward handling. The M323.291 is sized to work with common pin blocks, insertion gauges and manual checking routines, enabling quick comparison checks and assembly gauging. For batch inspection, the pin’s consistent dimensions aid in establishing baseline measurements and can be used as a reference when comparing manufactured parts against drawing data. Where traceable records are required, the pin’s repeatability supports stable measurement series and clearer statistical process control entries. For precise shop-floor gauging with Metav IndustryLine reliability, contact Metav Werkzeuge to secure the M323.291 gauge pin and discuss delivery or batch supply tailored to workshop needs Technical data Article number: M323.291 GTIN: 4061905057885 eClass: 21170231 Core measurements Diameter: 2.91 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Features & materials Material: Special steel Designation: Workshop version Category: Gauge pin Label: Prüfstift, einzeln, 2,91mm, +/- 0.001 mm Länge 50 mm FAQ What is the exact tolerance of this gauge pin? The Metav IndustryLine gauge pin M323.291 is specified with a tolerance of ±0.001 mm, ensuring tight dimensional control for small-bore verification. Which material is used for the pin and how does it perform? This single gauge pin is made from special steel, chosen for durability and resistance to wear in typical workshop gauging and fixture environments. For which applications is this pin most suitable? The pin is intended for end measurements, plug-fit checks and fixture verification where a 2.91 mm reference is required; its 50 mm length provides useful engagement for many jigs and inserts. Is the pin supplied as a single item or part of a set? The product is described as a single gauge pin (single item) under the designation M323.291. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.92mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, sub‑micron repeatability and compact handling for reliable gauging in production and inspection. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application support. Test pin M323.292 — Single gauge pin, 2.92 mm, ±0.001 mm (Metav IndustryLine) Test pin M323.292 is a single precision gauge pin designed for accurate locating, go/no‑go checking and fixture alignment in workshop environments. Workshop version for robust use Diameter 2.92 mm with ±0.001 mm accuracy Length 50 mm for precise locating and inspection Precision that protects measurement certainty The M323.292 is engineered for repeatable results where tight tolerances matter. With a diameter tolerance of ±0.001 mm at 2.92 mm, the pin provides a stable reference for plug‑gauge checks, hole verification and fixture set‑up. The close tolerance reduces measurement scatter and enables consistent pass/fail decisions on production lines. The compact form factor maintains rigidity during probing while keeping handling straightforward in confined jigs and test fixtures. Such dimensional certainty supports faster quality decisions and reduces rework rates in small‑part manufacture. Robust build tailored to workshop conditions Manufactured from special steel, this single test pin combines wear resistance with dimensional stability under repeated use. The workshop specification means the component is prepared for everyday industrial handling, tooling stations and bench inspection tasks. Surface finish and material choice help maintain the nominal diameter over many cycles, so replacement intervals are minimised and toolroom downtime is reduced. The design is particularly suitable for mechanical inspection rigs where reliable locating without frequent recalibration is essential. Simple integration and practical handling advantages At 50 mm overall length the pin offers sufficient reach for common locating tasks while remaining easy to clamp or insert into holders and mandrels. The single‑piece format simplifies inventory and tool selection when a precise go/no‑go reference is required. Being lightweight yet stiff, the element is convenient for manual checking and straightforward to include in automated pick‑and‑place or gauging setups. Clear labelling and the compact footprint assist storage and quick identification in busy inspection areas. For reliable workshop gauging, request the Metav IndustryLine gauge pin M323.292 from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for application advice and supply details. Technical data Article number: M323.292 GTIN: 4061905057892 Manufacturer: Metav IndustryLine Facts Diameter: 2.92 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Eclass: 21170231 Special features Material: special steel Version: workshop execution Single test pin format Intended use: locating, hole verification, fixture alignment FAQ What level of dimensional accuracy does the pin offer? The M323.292 delivers an accuracy of ±0.001 mm, suitable for tight go/no‑go checks and high‑precision locating tasks. Can this test pin be used in automated gauging systems? Yes, the compact single‑piece design and stable dimensions make the pin compatible with automated pick‑and‑place and gauging fixtures where a precise reference diameter is required. What material is the pin made from and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability to maintain the nominal diameter under repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.93mm Gauge Pin Length 50mm ±0.001mm Workshop Finish, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ultra‑tight ±0.001 mm tolerance, a compact 2.93 mm diameter and a 50 mm precision ground length for consistent end‑dimension checks; order the item directly via Metav Werkzeuge or consult our specialists for application advice. M323.293 Gauge Pin — 2.93 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.293 gauge pin is a single, high‑precision control pin designed for dimensional checks of small bores and fine mechanical components in production and inspection environments Diameter 2.93 mm with ±0.001 mm tolerance Hardened special steel for wear resistance Precision ground length 50 mm for stable seating Supplied individually for selective inspection Measurement certainty for small bores For repeatable quality checks in small components, the combination of a 2.93 mm nominal diameter and an ±0.001 mm tolerance reduces ambiguity at the pass/fail decision point. The pin is precision ground, which minimises form and surface defects that could otherwise bias measurements. In practice this means reliable seating in the measured bore and reproducible results across multiple checks, supporting efficient process control and fewer downstream rejects. Robust construction that keeps inspection stable Manufactured from special steel and finished by precision grinding, the pin resists wear and maintains dimensional integrity over many cycles. The 50 mm length provides a stable datum when probing through thin workpieces or checking stepped bores, while the hardened surface improves service life under frequent use. This construction lowers the need for frequent replacement and helps maintain inspection throughput in workshop and production settings. Practical use and integration into inspection routines Delivered as an individual control pin, this product fits straightforwardly into go/no‑go fixtures, transfer gauges or manual inspection benches used for end‑dimension verification. The compact form factor makes the pin suitable for close‑tolerance checks in instrument, connector and micro‑mechanical assemblies. Clear, measurable specifications assist purchasing and quality documentation while the small mass reduces the risk of handling damage during routine use. Choose Metav IndustryLine when tight tolerances matter; contact Metav Werkzeuge for tailored advice or to secure the M323.293 for immediate use — eMail: info@metav-werkzeuge.com or Phone: +49 2822 7131930 Technical data Article number: M323.293 GTIN: 4061905058776 Brand: Metav IndustryLine Facts Diameter: 2.93 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: special steel Precision ground surface Workshop version Supplied individually FAQ What is the dimensional tolerance of this control pin? The M323.293 gauge pin is manufactured to a tolerance of ±0.001 mm, enabling very fine discrimination in inspection tasks. Which materials is the pin suitable for inspecting? The control pin is intended for dimensional checks of metallic bores and small mechanical parts; the special steel construction provides wear resistance compatible with typical production environments. How is the pin supplied? This gauge pin is supplied individually for selective inspection and integration into existing fixture or bench setups. Can the pin be used in go/no‑go fixtures? Yes — the precision ground diameter and rigid 50 mm length make the pin suitable for direct use in go/no‑go fixtures and transfer gauges for end‑dimension verification. Which brand and SKU should be referenced when ordering? Refer to Metav IndustryLine, SKU M323.293, for ordering and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.94mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Supplied in Case - Metav IndustryLine
Precision end‑size checks benefit from the combination of a 2.94 mm nominal diameter, ±0.001 mm tolerance and 50 mm overall length; the workshop‑grade special steel construction supports repeatable measurements and extended service life. Order this gauge pin directly via Metav Werkzeuge or consult the Metav advisors for specification support. M323.294 Gauge pin — 2.94 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.294 gauge pin is a workshop‑grade inspection pin designed for precise end‑size verification and routine production control in machine shops and quality departments. Diameter tolerance ±0.001 mm for micro‑accuracy Length 50 mm for consistent end‑measure checks Hardened special steel for long‑term wear resistance Reliable geometry for repeatable end‑size verification A consistently accurate gauge element reduces rework and inspection time. With a nominal diameter of 2.94 mm and a certified positional variation of ±0.001 mm, this inspection pin provides the dimensional certainty required for final size checks and close‑tolerance fits. The controlled geometry minimises measurement scatter and supports clear go/no‑go decisions at the production line; the compact 50 mm length eases handling while maintaining sufficient contact area for stable measurements. Emphasis on repeatability helps labs and workshop inspectors meet process capability targets with fewer sample points. Robust construction suited to workshop conditions Manufactured from special steel in a workshop‑grade finish, the pin resists wear from frequent insertion and withdrawal. The material selection and heat treatment deliver reliable wear resistance and stable dimensions over many cycles, reducing the need for frequent replacement. Where gauge elements are stored and transported between benches, the solid construction keeps datum conformity and protects the critical measuring surface. This durability translates into lower operating costs and more consistent inspection results in everyday shopfloor use. Simple integration into quality workflows Compact and single‑piece in design, the pin is intended for straightforward use in end‑measure verification, assembly checks and fixture validation. Its clear specification supports traceable documentation and easy inclusion in inspection plans or measurement routines. The precise tolerance helps shorten decision time during quality control, improving throughput without sacrificing accuracy. Where traceable parts and clear audit trails are required, the concise technical definition simplifies communication between production, quality and procurement teams. Contact Metav Werkzeuge for specification advice, availability and tailored delivery from Emmerich to support immediate integration into production control Technical data Article number: M323.294 GTIN: 4061905058783 Manufacturer: Metav IndustryLine (Metav Werkzeuge GmbH) Facts Diameter: 2.94 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Material: special steel Version: workshop execution Supply: single inspection pin for end‑size checks Application: end‑measure verification and production control FAQ What are the nominal size and tolerance of this gauge pin? The M323.294 gauge pin has a nominal diameter of 2.94 mm and a tolerance of ±0.001 mm, suitable for tight end‑size inspections. What material is used and how does it affect longevity? The pin is made of special steel, a choice that increases wear resistance and keeps critical dimensions stable under repeated use in workshop environments. Is the pin supplied individually or as a set? The product is supplied as a single inspection pin, intended for direct use in measurement routines or as a replacement element in inspection fixtures. Can this pin be used for go/no‑go checks and fixture validation? Yes, the defined 2.94 mm geometry and ±0.001 mm tolerance make it appropriate for go/no‑go assessments, end‑measure verification and fixture alignment tasks. How does this component support production efficiency? By delivering high repeatability and clear dimensional specification, the pin reduces inspection ambiguity and supports faster, more reliable quality decisions on the shopfloor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.95mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high-precision gauging with a 2.95 mm nominal diameter and ±0.001 mm tolerance combined with robust workshop suitability and secure transport packaging; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.295 — 2.95 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.295 designed for precise end‑measure checks and workshop gauging tasks, supplied as a single plug gauge in a protective transport box. 2.95 mm nominal diameter, tolerance ±0.001 mm Length 50 mm for consistent end‑measure checks Made from special steel, workshop version Supplied in a protective transport box High precision for repeatable verification This single gauge pin offers a nominal diameter of 2.95 mm with a tolerance of ±0.001 mm, providing the dimensional stability required for repeatable end‑measure verification and reference checks in production. The very tight tolerance class means fewer rejects during go/no‑go assessments and a clearer differentiation between nominal and out‑of‑tolerance conditions. The compact geometry and single‑piece design reduce handling variability and enable fast, objective inspection cycles. Robust workshop construction and handling benefits Manufactured in special steel and delivered as a workshop version, the pin combines dimensional integrity with durability for regular use at the machine bench or inspection station. The 50 mm length gives useful engagement depth while remaining easy to handle; the modest component weight supports quick manual positioning. Delivery in a protective transport box safeguards the measuring surface against knocks and contamination during storage or transit, maintaining accuracy over repeated uses. Practical applications and integration into inspection routines Suitable as a reference element for hole gauges, fixtures and comparative checks, this plug gauge is optimised for routine workshop control and sample inspection. The high precision tolerance permits confident use for verifying finishing operations and final dimensions where sub‑micrometre deviations would otherwise lead to rework. The single‑item format allows targeted replacement or expansion of existing gauge sets without committing to a full kit. For reliable workshop gauging and tailored advice on suitability, choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge for delivery and consultancy from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M323.295 GTIN: 4061905054556 Manufacturer: Metav IndustryLine Facts Diameter: 2.95 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Packaging: protective transport box Special features Material: special steel Workshop version Single gauge pin Category: gauge pins FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 2.95 mm and a tolerance of ±0.001 mm, suited to high‑precision end‑measure verification. Is the pin suitable for regular workshop use? Yes, the workshop version of the M323.295 is made from special steel and supplied in a protective transport box for routine handling and storage. Can this gauge pin be used as a reference in fixture checks? The M323.295 plug gauge is suitable for comparative checks and fixture verification where a small, precise reference diameter is required. What does the single‑item supply mean for inventory? Supplying the gauge pin individually allows targeted replacement or selective expansion of gauge sets without purchasing a full kit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.96mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade durability, sub‑micron accuracy ±0.001 mm and a compact 50 mm length for accessible end‑measure checks; order directly via Metav Werkzeuge or consult our specialists for application guidance. Test pin, single, 2.96 mm, ±0.001 mm, 50 mm — Precision probe (Metav IndustryLine) The Test pin, single, 2.96 mm, ±0.001 mm, 50 mm is a workshop‑grade precision probe designed for reliable end‑dimension checks and fixture verification across demanding metalworking environments. Workshop‑grade accuracy ±0.001 mm Precise diameter 2.96 mm 50 mm length for deep reach Delivered in protective transport box Consistent sub‑micron accuracy for tight tolerances This probe delivers ±0.001 mm declared repeatability, making it a suitable choice where tight tolerances and repeatable results are imperative. The slender 2.96 mm diameter provides targeted contact for small features and end‑measure verifications, while the 50 mm length gives access to recessed seats and bore terminations without compromising stability. The precise geometry of the tip reduces measurement variation and supports reliable process control in routine inspection tasks. Robust workshop design for heavy use Manufactured in special steel and specified as a workshop edition, the probe is built to withstand regular handling and the rigours of a production environment. At approximately 0.006 kg, the component is light enough for easy positioning yet engineered for dimensional stability during tactile contact. Delivery in a protective transport box ensures the probe arrives undamaged and ready for storage with minimal risk of tip wear during logistics. These attributes combine to reduce downtime and keep inspection cycles efficient. Easy integration into inspection workflows The probe is intended for use as a dedicated contact element in fixture checks, end‑measure routines and tactile verification set‑ups. Its nominal diameter and standard length make it compatible with common pin holders and measuring fixtures, facilitating quick replacement or reconfiguration within existing inspection jigs. Traceable identifiers such as GTIN 4061905054563 and the internal article code support inventory management and quality documentation, helping to maintain consistent quality standards across production batches. For precise end‑measure checks with proven workshop resilience, choose the Metav IndustryLine probe and contact Metav Werkzeuge for tailored application advice and supply options Technical data Article number: M323.296 GTIN: 4061905054563 EClass: 21170231 Manufacturer: Metav IndustryLine Facts Diameter: 2.96 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.006 kg Measurement range: 2.96 mm (nominal) Special features Material: special steel Workshop edition Delivered in protective transport box FAQ What level of accuracy does this test pin provide? The test pin achieves an accuracy of ±0.001 mm, enabling sub‑micron repeatability for precise end‑measure checks with the Metav IndustryLine probe M323.296. Is the probe suitable for fixture and end‑measure verification? Yes, the probe’s 50 mm length and 2.96 mm diameter make it well suited for fixture verification and end‑dimension checks in workshop environments. What material is the pin made from? The pin is manufactured from special steel, specified for durability and consistent contact performance during regular use. How is the test pin delivered for transport and storage? The probe is supplied in a protective transport box, ensuring the contact tip remains protected during shipment and storage. Can the probe be used with standard pin holders and measuring fixtures? The nominal diameter and length are compatible with common pin holders and measuring fixtures, and the item is listed under SKU M323.296 for straightforward replacement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.97mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact single test pin that combines submicrometre repeatability, a narrow Ø 2.97 mm profile and a 50 mm length for dependable end‑size checks. The probe’s ±0.001 mm tolerance and workshop construction support consistent inspection results and reduced rework — order directly via Metav Werkzeuge or contact our consultants for specification advice. M323.297 Test pin — Single precision probe, Ø 2.97 mm, ±0.001 mm The M323.297 test pin is a single precision probe designed for end‑size verification and fine inspection tasks in workshop and quality‑control environments Precision tolerance ±0.001 mm Diameter Ø 2.97 mm for tight fits Length 50 mm for deeper checks Workshop‑grade construction Delivered in transport case Precise control for end‑size verification Built to support repeatable measurement processes, this probe offers a ±0.001 mm tolerance that makes it suitable where tight dimensional control is required. The exceptionally small diameter of Ø 2.97 mm minimises interference when probing narrow bores or delicate features, while the fine tolerance reduces measurement uncertainty during comparative or go/no‑go checks. In practice, this level of precision shortens inspection time and lowers scrap rates by providing reliable pass/fail data that can be integrated into existing calibration routines. Durable workshop design that endures daily use Manufactured from special steel, the probe has been configured for workshop environments where handling and tool changes happen frequently. The 50 mm shaft length provides enough reach for recessed features without compromising stiffness; the robust material choice maintains form and contact integrity across repeated cycles. Supplied in a dedicated transport case, the single test pin stays protected during storage and shipment, ensuring the measurement tip arrives ready for immediate use on the shop floor. Easy handling and seamless metrology integration This single test pin is intended for straightforward insertion into gauge holders and inspection fixtures used in small‑part measurement. The compact mass and low inertia of the probe allow for swift positioning and stable contact during checks, supporting efficient quality‑control workflows. As a precision probe, it is compatible with routine inspection setups and can be an effective component in comparative gauging, fixture validation or manual inspection stations where repeatability and accessibility matter. A precision partner you can rely on Offered under the Metav IndustryLine, the product benefits from Metav’s practical focus on making precision accessible to workshops and industry alike. The combination of proven materials, tight tolerances and workshop suitability reflects a pragmatic approach: accurate measurements without unnecessary complexity. This aligns with Metav’s commitment to dependable supply and a broad product range that keeps production moving with fewer suppliers to manage. For assured end‑size verification and workshop‑grade performance, request the Metav IndustryLine M323.297 through Metav Werkzeuge or speak to our consultants for tailored recommendations. Technical Data Article number: M323.297 GTIN: 4061905054570 ECLASS: 21170231 Brand: Metav IndustryLine Facts Diameter: 2.97 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Material: special steel Special features Workshop version Delivered in transport case Single test pin for end‑size checks Category: Test pins FAQ What level of accuracy does this probe provide? The M323.297 test pin offers a tolerance of ±0.001 mm, which is suitable for tight end‑size verification and high‑precision comparative checks. Is the probe suitable for use in workshop inspection fixtures? Yes, the workshop‑grade construction and 50 mm length make the probe well suited to manual inspection fixtures and standard gauge holders used in the shop environment. What material is the test pin made from? The shaft is made from special steel, chosen for its durability and dimensional stability under frequent use. Does the product include storage or transport protection? The test pin is supplied in a transport case, ensuring secure handling and protection during shipment and storage. Which applications benefit most from this probe? The probe is ideal for end‑size verification, small‑bore checks and precision inspection tasks where a narrow diameter and submicrometre repeatability are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.98mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of high metrological certainty, compact workshop design and transport-ready packaging to ensure repeatable end‑mass checks in daily production. The combination of ±0.001 mm tolerance, 2.98 mm diameter and robust special steel construction supports reliable inspection routines; order directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.298 — test pin, 2.98 mm diameter, ±0.001 mm, 50 mm length The Gauge pin M323.298 is a workshop-grade precision master pin for end‑mass verification and small‑bore inspection in production and quality control environments. Workshop-grade precision ±0.001 mm 2.98 mm diameter, ground to tolerance 50 mm length for standard checking Delivered in protective transport case Precision where measurement matters A compact master pin designed for accurate end‑mass and bore checking delivers measurable benefits in quality assurance workflows. With a diameter of 2.98 mm and an outstanding tolerance of ±0.001 mm, the component provides repeatable reference points for go/no‑go tests and plug inspections. The finely ground surface reduces measurement uncertainty caused by surface roughness, while the workshop orientation ensures practical robustness during frequent handling. By specifying a tight tolerance, this pin supports faster root‑cause analysis when a process drifts, shortening downtime and improving first‑pass yield. Robust construction for industrial use Manufactured from special steel, the pin combines wear resistance with dimensional stability under normal workshop conditions. The 50 mm length offers sufficient engagement for many small‑bore checks while remaining easy to handle and position. The labelled workshop execution indicates a build standard suited to regular use rather than delicate laboratory handling; this makes the component ideal for production inspection benches, toolrooms and assembly jigs where resilience is as important as metrological quality. The polished finish eases insertion and reduces the risk of scoring sensitive bores. Ready for routine inspection and transport Delivered in a protective transport case, the pin arrives ready for immediate use and for secure storage between shifts. The packaging choice supports damage‑free logistics and simple inventorying on the shop floor. Lightweight at approximately 0.006 kg, the pin can be included in portable inspection sets without adding noticeable bulk, enabling technicians to perform quick checks across multiple machines. Traceable identification through the SKU and GTIN facilitates procurement and stock control in larger operations, aligning with Metav’s emphasis on dependable supply chains for precision tools. For precise end‑mass verification and reliable shop‑floor performance, contact Metav Werkzeuge to secure the M323.298 gauge pin and to discuss delivery and stock options from Emmerich. Technical data SKU: M323.298 GTIN: 4061905055263 Manufacturer: Metav IndustryLine Facts Diameter: 2.98 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: Special steel Workshop execution Delivered in protective transport case Intended use: end‑mass / bore checking FAQ What level of precision does this gauge pin provide? The gauge pin M323.298 provides a precision of ±0.001 mm, making it suitable for tight end‑mass and bore checks in production environments. Which material is used for the pin and how does it affect wear? The pin is made from special steel; this material offers good wear resistance and dimensional stability for routine workshop use with the M323.298 test pin. Is the pin supplied ready for use and transport? Yes. The M323.298 is supplied in a protective transport case, allowing immediate use and secure handling between inspections. What are typical applications for this test pin? Typical applications include end‑mass verification, small‑bore inspection and plug checks in assembly, toolroom and quality control stations using the M323.298 gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.99mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of a workshop-grade gauge pin that combines ultra‑fine tolerance, a compact 50 mm length and robust special‑steel construction for consistent end‑measure checks; order the M323.299 directly via Metav Werkzeuge or consult our advisers if application support is required. M323.299 Gauge pin (2.99 mm, ±0.001 mm) — Metav IndustryLine The M323.299 is a workshop‑grade gauge pin designed for precise end‑measure verification and fixture set‑up in metrology and production environments. High‑precision ±0.001 mm tolerance Diameter 2.99 mm for tight fits Length 50 mm for fixture positioning Supplied in a protective transport case Repeatable end‑measure verification with micrometre accuracy A small component with a demanding task: the gauge pin delivers a tolerance of ±0.001 mm, enabling repeatable checks where tight clearances determine part acceptance. This level of precision reduces uncertainty in go/no‑go assessments and supports consistent assembly and jig alignment. The specified tolerance corresponds to micrometre‑class performance, making the pin suitable for high‑precision workshops and quality control loops where reproducibility directly cuts rework and inspection time. Robust workshop design for everyday handling Built as a workshop‑grade tool from special steel, the pin balances durability with manageable mass (approx. 0.006 kg). The 50 mm length provides convenient handling for fixture set‑up and in‑process checks while remaining compact enough for dense inspection benches. Supplied in a protective transport case, the item resists transit damage and is ready for immediate use on the shop floor, supporting reliable measurement routines across repeated cycles. Easy integration into inspection workflows Designed for simple inclusion in dimensional checks, the pin works as a reference dowel for setting end stops, verifying bore sizes and validating mating features. The compact diameter of 2.99 mm makes it ideal for tight‑tolerance fits, while the precise manufacture supports accurate comparison with plug gauges and digital measuring equipment. Traceable identification via SKU and GTIN facilitates stock management and tool tracking within existing quality systems. For tailored advice on fixture integration or availability of the Metav IndustryLine M323.299 gauge pin, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.299 GTIN: 4061905055270 Label: Prüfstift, einzeln, 2,99mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.99 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Material: Special steel Workshop execution Supplied in protective transport case Category: Gauge pins FAQ What applications suit this gauge pin? The M323.299 gauge pin is intended for end‑measure checks, fixture set‑up and verification of tight‑tolerance bores in production and inspection workflows. Is the material resistant to workshop wear? Manufactured from special steel, the M323.299 offers good wear resistance for routine workshop use while maintaining the specified tolerance. Can this pin be used with digital inspection systems? Yes, the precision dowel is compatible with digital gauges and bench setups as a repeatable reference for size and fit verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 mm Ceramic Measurement Sphere (Si3N4) 0.003 mm Accuracy, HV1400-1700 Hardness - Metav IndustryLine
This ceramic gauge ball combines Si3N4 material, a 20 mm diameter and 0.003 mm accuracy to provide a stable reference for calibration and inspection; its high hardness and fine surface finish ensure long-term reproducibility. Order directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge ball (Si3N4) — 20 mm, 0.003 mm accuracy — Metav IndustryLine Ceramic gauge ball (Si3N4) is a precision reference sphere for gauges, fixture alignment and calibration tasks in quality control and mechanical inspection. Si3N4 ceramic, extreme wear resistance Diameter 20 mm with tight diameter tolerance Accuracy 0.003 mm for reference measurements High-precision reference for consistent results A compact reference sphere made from Si3N4 offers a quantifiable benchmark for repeatable measurements. The combination of 0.003 mm accuracy and a very fine surface finish minimises measurement scatter, making the component ideal for comparative checks, gauge setting and fixture calibration. The consistent geometry of the sphere reduces form-related uncertainty and supports traceable inspection routines, which accelerates decision-making in production and QA processes. Durable construction lowers long-term costs Manufactured in silicon nitride (Si3N4) and exhibiting hardness HV1400–1700, the gauge sphere resists wear and maintains its dimensional integrity under frequent contact. The exceptionally low surface roughness contributes to minimal contact deformation and extended service intervals, reducing the need for frequent replacements. In practice, this leads to lower lifecycle costs and fewer interruptions to inspection workflows while preserving measurement confidence. Versatile in metrology and toolmaking applications Compact and stable, the sphere suits a wide range of applications from gauge blocks and plug gauges to fixture references and tactile probing. The tight diameter tolerance of 0.00008 mm and proven surface quality make it suitable for both laboratory calibration benches and shop-floor verification routines. The product is easily integrated into existing measurement chains and supports repeatable, comparable results across operators and instruments. Choose the Metav IndustryLine ceramic gauge ball for reliable calibration performance and contact Metav Werkzeuge in Emmerich for tailored advice or to request delivery and specification support. Technical data SKU: M318.446 GTIN: 4054469184432 Material: Ceramic (Si3N4) Diameter: 20 mm Accuracy: 0.003 mm Facts Weight: 0.08 kg Hardness: HV1400–1700 Surface roughness Ra: 0.00001 mm Diameter tolerance: 0.00008 mm Special features High wear resistance Smooth surface for low contact deformation Suited for gauges, fixtures and calibration tasks Compact design for easy handling and storage Category: Gauges / Measuring devices FAQ What is the intended use of this ceramic gauge ball? The ceramic gauge ball (Si3N4) 20 mm is designed as a precision reference for calibration, fixture alignment and comparative measurements in inspection and metrology workflows. How durable is the material under repeated use? Made from silicon nitride with a hardness of HV1400–1700, the sphere offers excellent wear resistance and long service life even under frequent contact. Can this sphere be used with tactile probes and gauge setups? Yes, the tight geometry and fine surface finish make the sphere suitable for tactile probing, gauge setting and use as a reference in measuring fixtures. Is the diameter and accuracy traceable for quality records? The product specification lists a diameter of 20 mm with an accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, making it appropriate for traceable quality-control documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 mm Gauge Ball Pair, Hardened Chrome Steel, Accuracy 0.003 mm, Diameter Tolerance 0.00008 mm - Metav IndustryLine
Take advantage of the combination of hardened chrome steel construction, tight diameter tolerance and a matched delivery to secure reproducible reference points in inspection and fixture tasks. The paired spheres deliver consistent comparative measurements and long service life thanks to high hardness and a super-fine surface finish. Order the gauge ball pair directly via Metav Werkzeuge or consult the technical advisers for application-specific guidance. Gauge Ball Pair M318.430 — hardened chrome steel, 20 mm, 0.003 mm accuracy (Metav IndustryLine) The Gauge Ball Pair M318.430 is a precision reference set for gauging, calibration and fixture alignment in inspection and machine construction, designed to provide reproducible contact points and to simplify comparative measurements Hardened chrome steel, wear-resistant (>HRC 62) Diameter 20 mm with 0.00008 mm tolerance Surface roughness Ra 0.00001 for reference accuracy Supplied as a matched pair for inspection setups Consistent reference points for repeatable inspection results The matched spheres serve as stable contact elements where reproducibility is essential. With a specified accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, the pair provides highly consistent reference geometry for comparative gauging, fixture location and verification of measuring equipment. The very low surface roughness (Ra 0.00001) reduces local contact variability and supports reliable force transmission during probing or mechanical contact checks. This combination shortens setup time and reduces uncertainty in serial inspection tasks. Robust material and surface quality for long service life Manufactured from hardened chrome steel, the balls resist wear in repeated contact cycles; hardness exceeds HRC 62, ensuring dimensional stability under load and extended lifetime in workshop use. The hardened substrate plus precision finishing make the spheres suitable as permanent reference elements in gauges, go/no‑go fixtures or as datum balls for comparative setups. The high hardness and fine finish mitigate profile changes over time, preserving calibration intervals and lowering lifecycle costs compared with softer reference components. Matched set simplifies integration into workflows Delivered as a matched pair, the set reduces the need for individual sorting and guarantees that comparative measurements are taken between two mating elements with minimal deviation. The compact format and light mass (0.08 kg) allow easy handling and mounting in inspection fixtures, test benches or portable measurement rigs. The spheres are primarily intended for use in gauging applications and support rapid interchangeability when multiple reference points are required across fixtures or jigs. Contact Metav Werkzeuge today for application advice or to request compatible accessories and tailored measurement solutions from the Metav IndustryLine catalogue Technical Data Article number: M318.430 GTIN: 4054469184302 Material: Chrome steel, hardened Diameter: 20 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Surface roughness Ra: 0.00001 Hardness: > HRC 62 Weight: 0.08 kg Set content: 2 pieces Facts High repeatability for gauging tasks Matched pair delivery Compact, portable reference elements Special features Precision-ground spherical geometry Suitable as reference contacts in fixtures Category: Gauges FAQ What applications are suitable for these gauge balls? The gauge ball pair M318.430 is intended for gauging, fixture datum points and comparative inspection tasks where precise, repeatable contact points are required. Is the material suitable for heavy-duty workshop use? Yes. The spheres are made of hardened chrome steel with hardness > HRC 62, providing wear resistance for repeated contact in workshop and shop-floor inspection environments. How does the matched pair delivery help in measurement setups? Supplied as a matched pair, the two spheres are already paired to reduce statistical deviation between mating reference points, simplifying fixture setup and comparative measurements. What level of surface finish and tolerance can be expected? The pair features a surface roughness Ra 0.00001 and a diameter tolerance of 0.00008 mm, providing very low local contact variability for precise reference use. Is the set traceable for quality assurance? Traceability depends on the calibration and documentation required for a specific application; the M318.430 is manufactured to tight production tolerances suitable for integration in calibrated inspection systems Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 mm Limit Gauge Mandrel, Wear Allowance On Good Side, Hardened Steel, DIN 7162 - Filetta
Take advantage of a hardened-steel inspection pin that meets DIN 7162 and delivers a clear 20 mm pass/fail result with a wear allowance on the GO side; order directly via Metav Werkzeuge or ask our consultants for application advice. Limit plug gauge MS911.224 — hardened steel plug gauge, DIN 7162 (Filetta) The limit plug gauge MS911.224 is a hardened-steel inspection pin designed for straightforward GO/NO‑GO verification of bore diameters in production and inspection environments Hardened steel construction DIN 7162 compliant gauge 20 mm inspection diameter Wear allowance on GO side Consistent pass/fail control for series inspection The plug is designed for fast, unambiguous GO/NO‑GO checks, reducing downstream rework by confirming bore conformity at the control stage. Constructed from hardened steel to resist deformation, the pin gives repeatable results even under frequent use. Compliance with DIN 7162 ensures the acceptance criteria are standardised, so inspection staff can apply the gauge confidently across batches. This approach improves throughput by shortening check cycles and simplifies traceability in routine quality documentation. Robust design that lowers maintenance cycles A hardened body and attention to running clearances mean the gauge keeps its dimensional integrity for longer, which reduces the frequency of requalification. The built-in wear allowance on the GO side prolongs the service interval before a gauge requires replacement or resharpening, translating into lower lifecycle cost for inspection tooling. For workshops that prioritise uptime, the durable construction supports continuous use in metalworking and assembly lines where reliable tactile confirmation is required. Practical compatibility and handling in the workshop The compact plug format and plain cylindrical shank make the gauge easy to handle and quick to seat in bores for rapid checks. Marked as a 20 mm inspection diameter, the pin is straightforward to integrate into existing GO/NO‑GO benches or manual inspection routines. The simple geometry facilitates cleaning and visual inspection for damage, while the standardised dimensions enable straightforward storage and organisation alongside other gauge pins and measuring instruments. For reliable, standardised bore verification choose the Filetta limit plug gauge MS911.224 — contact Metav Werkzeuge in Emmerich for ordering support or specific application guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: MS911.224 Material: Hardened steel Standard: DIN 7162 Diameter: 20 mm Core data Product type: Limit plug gauge / plug gauge pin Brand: Filetta Special note: Wear allowance on GO side Special features Suitable for GO/NO‑GO inspection Designed for repetitive series checks Simple cylindrical shank for handling FAQ What is the intended application of this plug gauge? The plug gauge is intended for GO/NO‑GO verification of bore diameters in production and inspection settings; the MS911.224 by Filetta provides tactile pass/fail assessment for 20 mm bores. How does the wear allowance benefit inspection intervals? The wear allowance on the GO side extends usable life by providing a controlled margin before the gauge reaches tolerance limits, reducing replacement frequency for the MS911.224. Is the gauge compliant with industry standards? Yes, the gauge conforms to DIN 7162, ensuring it matches recognised dimensional and tolerance conventions for limit plug gauges. Can this gauge be used for rough or soft materials? The hardened-steel construction is optimised for metalworking environments; for very soft or abrasive materials, handling procedures should be adjusted to avoid premature surface damage. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
20 mm Limit Gauge Pin H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Reliable bore control through DIN 2245 H7 conformity and hardened gauge steel construction delivers consistent acceptance decisions; the compact 20.0 mm diameter and low mass simplify handling and reduce inspection time. Order the limit plug gauge M314.020 directly via Metav Werkzeuge or ask our consultants if needed. Limit plug gauge M314.020 — 20.0 mm H7, DIN 2245 (Metav IndustryLine) The limit plug gauge M314.020 is designed for rapid, standards‑based verification of 20.0 mm bores in production and inspection environments. Hardened gauge steel construction DIN 2245 H7 tolerance for accurate checks Compact 20.0 mm diameter, 0.2 kg mass Traceable conformity for reproducible bore decisions The gauge is manufactured to DIN 2245 and sized to H7, providing a straightforward pass/fail result for nominal 20.0 mm bores. This standards‑based approach removes ambiguity from routine inspections: measuring personnel gain a clear acceptance criterion without complex calculations. Using a dedicated plug gauge reduces cycle time during batch inspection and supports consistent quality documentation, helping to keep production tolerances under control. Robust material choice for extended service life Constructed from hardened gauge steel, the tool resists wear from repeated seating inside nominal bores and maintains dimensional stability over many inspection cycles. The modest mass of 0.2 kg and the compact form factor make handling ergonomic for single‑operator checks while the hardened finish sustains accurate contact geometry. The combination of durable material and standardised manufacture contributes to lower lifecycle costs through reduced rework and fewer replacements. Simple to use in shopfloor and inspection routines As a limit plug gauge, operation is immediate: the gauge is seated in the bore to verify conformity to the H7 tolerance; a smooth fit indicates acceptance, while any interference signals an out‑of‑tolerance condition. The straightforward go/no‑go logic minimises training time and speeds up first‑article and in‑process checks. For traceability, the compact design integrates easily into inspection stations, supplying an objective decision step that complements micrometre and caliper measurements. Practical placement in quality workflows Well suited to machine shops, assembly lines and quality control benches, the gauge supports routine verification of mating components, housings and bores where a 20.0 mm nominal size is required. The tool aligns with a pragmatic quality regime: quick checks at the machine, final inspection before dispatch, or spot audits during production runs. As a Metav IndustryLine product, it arrives ready for immediate use within established metrology chains and is straightforward to store and handle between checks. For reliable, standards‑based bore inspection choose the Metav IndustryLine limit plug gauge M314.020 and contact Metav Werkzeuge in Emmerich for supply and application advice. Technical Data Article number: M314.020 GTIN: 4054469121499 Manufacturer: Metav IndustryLine Facts Diameter: 20.0 mm Weight: 0.2 kg Tolerance: H7 Special features Material: gauge steel, hardened Standard: DIN 2245 Category: Lehren (gauges) FAQ What size of bore is this gauge intended to check? The limit plug gauge M314.020 is made for inspection of 20.0 mm nominal bores and verifies conformity to the H7 tolerance class. Which standard governs this plug gauge? Manufacture and dimensions comply with DIN 2245; the Metav IndustryLine limit plug gauge M314.020 is produced accordingly. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened gauge steel; this material preserves contact geometry and resists wear during repeated inspections. How is the acceptance determined with this tool? A smooth, unrestricted seating of the gauge into the bore confirms acceptance to H7, while any tightness indicates out‑of‑tolerance condition requiring further investigation. Can the gauge be used on the shopfloor for routine checks? Yes — the compact design and modest mass make the Metav IndustryLine plug gauge suitable for fast, repeatable checks at the machine or inspection bench. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 mm Limit Gauge Pin Wear Measurement Face Reference, Hardened Steel, DIN 7162 - Filetta
Take advantage of DIN 7162 conformity, hardened steel construction and the integrated wear allowance on the go side for dependable bore verification. Order this limit plug gauge directly via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7 – 20 mm, hardened steel (DIN 7162) by Filetta A limit plug gauge G7 designed for rapid go/no-go checks of cylindrical bores in production and inspection environments Hardened steel for long service life Manufactured to DIN 7162 standard Wear allowance on the go side Suitable for bore verification and QC Reliable measurements through recognised standards The gauge is manufactured to DIN 7162, which ensures consistent dimensions and interchangeability across inspection routines. For a nominal size of 20 mm, the plug gauge provides an immediate go/no-go decision, eliminating lengthy measurement evaluation processes. This standard-led approach supports efficient quality control, reduces scrap rates and shortens inspection cycles by delivering clear, repeatable outcomes at every station. Durable construction that reduces downtime Made from hardened steel, the instrument tolerates repeated use on the shop floor while maintaining dimensional stability. The incorporated wear allowance on the go side compensates for gradual material loss during routine checking, extending the service life before any rework or replacement becomes necessary. This pragmatic design reduces unplanned stoppages and lowers total cost of ownership by keeping maintenance intervals predictable. Practical integration for workshop and production use Sized for common bore checks, the plug gauge is ideal for quick verification during assembly, final inspection or incoming goods control. Its straightforward go/no-go functionality accelerates throughput without requiring complex measuring equipment or extensive operator training. The robust design and adherence to DIN 7162 make it suitable for use in machine shops, tool rooms and quality laboratories where rapid, trustworthy pass/fail decisions are required. Reference: model MS911.182 for ordering and stock enquiries. Contact Metav Werkzeuge for expert advice on integrating Filetta limit plug gauges (DIN 7162) into existing inspection routines and to secure reliable supply from our Emmerich warehouse Technical Data Article number: MS911.182 Material: hardened steel Standard: DIN 7162 Size: 20 mm Facts Diameter: 20 mm Special features Wear allowance on the go side Designed for go/no-go checks Robust hardened-steel construction FAQ What is the primary use of this limit plug gauge? This limit plug gauge is intended for fast go/no-go verification of cylindrical bores, providing a clear pass/fail result for production and inspection tasks. What material is the gauge made from and why does it matter? The gauge is produced from hardened steel, which ensures wear resistance and dimensional stability under frequent use, supporting reliable long-term measurements. Which standard does the product comply with? Manufactured to DIN 7162, the gauge meets recognised dimensional and manufacturing criteria for plug gauges used in industrial quality control. How does the wear allowance affect inspection intervals? The wear allowance on the go side compensates for gradual abrasion, extending useful life and allowing longer intervals between gauge replacement or rework; the item is listed as MS911.182 for ordering and inventory reference. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
20 mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the ring's certified dimensional class and hardened, lapped surface to secure repeatable reference measurements; combine durable construction, precise nominal diameter and standard conformity for reliable process control. Order the setting ring directly via Metav Werkzeuge or consult the specialists for application advice. Setting ring 20 mm — Gauge ring, hardened and lapped (DIN 2250) — Metav IndustryLine Setting ring 20 mm is a precision gauge ring intended as a stable reference for plug gauges, setting tasks and inspection work under workshop and production conditions. Hardened and lapped gauge steel Conforms to DIN 2250 / DIN 286, JS 3 Form C profile for standard applications Reliable reference for dimensional control The setting ring is manufactured to the tolerance class JS 3 under DIN 2250 and DIN 286, offering a consistent nominal diameter of 20 mm that serves as a baseline for go/no‑go checks and tool setting. Such conformity means the component can be incorporated into quality plans as a traceable reference, reducing uncertainty in process checks. Using a standardised reference ring simplifies transfer of measurements between machines and inspection stations and supports routine verification steps in production. Durable design that preserves accuracy Constructed from gauge steel, the ring is hardened and lapped to deliver a wear‑resistant bearing surface with stable contact geometry. The hardened substrate reduces plastic deformation under repeated engagement, while the lapped finish minimises surface asperities that could shift measured outcomes. These material and finishing choices translate into fewer replacements, less downtime and a longer service life for the reference tool—advantages that matter in continuous manufacturing environments where repeatability is essential. Practical handling and traceable identification The Form C profile provides a widely used geometry for easy seating with cylindrical gauges and fixtures, facilitating quick and reproducible engagement during inspection or setting routines. Clear identification is provided by the manufacturer SKU M313.020 and GTIN 4054469120584, which aids inventory and procurement workflows. The ring's design and labelling support straightforward integration into existing gauge sets and inspection procedures, helping to maintain process control with minimal adaptation. Metav’s role as a European quality filter underpins consistent supply and documentation for industrial users. For traceable reference measurements and durable workshop performance, select the Metav IndustryLine setting ring and contact Metav Werkzeuge for tailored advice or ordering via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M313.020 GTIN: 4054469120584 eClass: 21170104 Facts Diameter: 20 mm Customs tariff number: 90173000 Special features Material: Gauge steel, hardened and lapped Standards: DIN 2250; DIN 286, JS 3 Feature: Form C profile Categories: Gauge pins; Gauges FAQ What is the nominal diameter and tolerance class of this gauge ring? The setting ring has a nominal diameter of 20 mm and is manufactured to the JS 3 tolerance class in accordance with DIN 2250 and DIN 286. Can this ring be used as a reference for plug gauge calibration? Yes, the Metav IndustryLine setting ring (SKU M313.020) is suitable as a reference for plug gauge checks and for transferring dimensional standards in workshop inspection. What materials and surface finish are used to ensure durability? The ring is made from gauge steel, delivered hardened and lapped to provide wear resistance and a stable contact surface for repeated measurements. Which profile does the ring use and why is that relevant? The ring uses a Form C profile, which is a common geometry for engagement with cylindrical gauges and fixtures, enabling reproducible seating and practical handling. How is the product identified for procurement and inventory management? Identification is provided by the article number M313.020 and GTIN 4054469120584 to support ordering, stockkeeping and traceability. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 mm Test Pin Set With Holder, 1 mm Steps, Plastic Case - Metav IndustryLine
Take advantage of reliable repeatability, rapid incremental checks and robust workshop handling for smoother inspection routines; order the Gauge pin set M318.520 directly via Metav Werkzeuge or contact our consultants for tailored advice. Gauge pin set M318.520 — 1–20 mm, step 1 mm, Metav IndustryLine The Gauge pin set M318.520 is a precision reference set designed for dimensional verification and quick go/no-go checks in workshop inspection, fixture set‑up and quality control. Gauge range 1–20 mm 1 mm increments for fast checks Made from special steel Includes pin holder and transport case Accurate, repeatable pins that speed up inspections The set supplies graduated gauge pins in 1 mm steps across the 1–20 mm range, enabling fast sequential checks without tool changes. With a declared accuracy of 0.004 mm, the pins provide a reliable reference for bore sizing and clearance verification; this reduces uncertainty during inspection and helps avoid repeated measuring cycles. The compact gradation supports efficient workflows in small‑part inspection and fixture calibration, translating measurement precision into measurable time savings on the shop floor. Built for everyday workshop use and robust handling Constructed from special steel, each pin resists wear and maintains its dimensional integrity under regular use. The inclusion of a pin holder keeps the set organised during measurement routines and speeds selection of the required diameter, while the transport case protects the components between jobs and simplifies storage. The overall set weight of approximately 1.2 kg balances portability with a solid feel, making it straightforward to carry to the machine or inspection bench without compromising durability. Practical applications and integration into inspection processes This set suits bench inspectors, jig and fixture technicians and production engineers who need a dependable reference for bore checks, plug gauges and assembly trials. The even 1 mm step size supports progressive checking strategies and sampling plans, enabling clear pass/fail decisions and quick documentation of measured bores. Where traceability and consistent results matter, these pins form a simple, low‑complexity element of the measurement chain that complements calipers and micrometres. Choose the Metav IndustryLine gauge pin set for dependable, workshop‑ready inspection tools — contact Metav Werkzeuge for personalised advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M318.520 GTIN: 4054469129136 ECLASS: 21170231 SKU: M318.520 Facts Measurement range: 1.0–20.0 mm Increment / step: 1 mm Pieces per set: 20 Accuracy: 0.004 mm Weight: 1.2 kg Length (case): 50 mm Tariff number: 90173000 Special features Material: special steel With pin holder Delivered in transport case Set (graduated gauge pins) Category: gauge pins / inspection gauges FAQ What diameters are included in the set? The set contains graduated pins from 1 mm to 20 mm in 1 mm increments for systematic dimensional checks. Is the accuracy suitable for workshop quality control? Yes, the declared accuracy of 0.004 mm makes the set suitable for routine workshop inspection and go/no‑go verification. Does the set include storage or a holder? A pin holder and a protective transport case are provided to keep the pins organised and protected between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Ceramic End Gauge Hardened Zirconia, DIN 861 - Metav IndustryLine
Take advantage of the zirconia ceramic construction and DIN EN ISO 3650 accuracy together with an exceptionally high hardness (HV 1250) for reliable, long‑term measurement stability; order the Ceramic end measure directly via Metav Werkzeuge or consult the Metav advisors for integration and procurement assistance. Ceramic end measure 200 mm DIN 861 — zirconia ceramic end gauge with DIN EN ISO 3650 accuracy Ceramic end measure 200 mm DIN 861 is a compact, wear‑resistant end gauge intended for precise length reference and workshop calibration tasks, suitable where non‑magnetic and corrosion‑resistant measurement standards are required. Antimagnetic zirconia ceramic construction Accuracy to DIN EN ISO 3650 standard Hardness HV 1250, twice as hard as steel Consistent calibration results for production control The gauge provides repeatable dimensional reference by meeting the DIN EN ISO 3650 accuracy class, which supports reliable inspection routines and calibration chains. Defined tolerance limits under this standard make the instrument a sound choice for in‑process verification and reference checks. The clearance of ambiguous specifications simplifies traceability: results are comparable across shifts and locations because the reference is based on recognised ISO criteria rather than informal workshop norms. Material choice that reduces wear and interference Manufactured from zirconia ceramic, the gauge combines corrosion resistance and low thermal conductivity with an extremely high surface hardness of HV 1250. This hardness—approximately twice that of common steels—translates to slower surface degradation under repeated contact, reducing the frequency of surface rework and extending service intervals. The antimagnetic nature of the ceramic eliminates magnetic interference in sensitive setups and is advantageous in environments where magnetic parts would otherwise bias measurements. Compact cross-section for stable, repeatable handling The slim 35 x 9 mm cross‑section and a nominal length of 200 mm give a practical balance between stiffness and manoeuvrability: long enough to reference medium‑sized components while remaining easy to position and clamp. The section geometry provides good resistance to bending during hand placement, which helps maintain measurement integrity when used as a reference in production fixturing or gauge‑block comparisons. The profile is suited to standard bench workflows and small‑scale assembly jigs. Low‑maintenance reference that supports quality workflows As a wear‑resistant and stainless material reference, the gauge lowers total lifecycle effort: fewer surface refurbishments and less sensitivity to corrosive atmospheres mean fewer interruptions for maintenance. The durable surface finish also aids optical and tactile inspection methods by preserving flatness and edge definition. When implemented as part of a routine check sequence, the component contributes directly to reduced scrap rates and improved process capability indices, supporting cost‑efficient quality control. Contact Metav Werkzeuge to discuss how the Metav IndustryLine ceramic end measure can be incorporated into existing inspection procedures or to request a technical quotation; reach the Metav advisors at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Name: Ceramic end measure 200 mm DIN 861 SKU: M324.200 Manufacturer: Metav IndustryLine Facts Nominal size: 200 mm Cross section: 35 x 9 mm Hardness: HV 1250 Accuracy: DIN EN ISO 3650 Special features Material: zirconia ceramic Antimagnetic Wear‑resistant Stainless / corrosion‑resistant FAQ What materials is this end measure made from? The Ceramic end measure 200 mm DIN 861 is made of zirconia ceramic, a corrosion‑resistant and antimagnetic material chosen for its hardness and dimensional stability. Is the accuracy stated traceable to a recognised standard? Yes. Accuracy is specified according to DIN EN ISO 3650, ensuring traceable and comparable measurement references for production and inspection tasks. How does the ceramic material affect maintenance intervals? The high HV 1250 hardness and wear‑resistant surface of the gauge reduce surface wear, which typically extends maintenance intervals and lowers the need for resurfacing compared with steel references. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Setting Ring Hardened Gauge Steel Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of hardened, lapped gauge steel and DIN-certified tolerances for reliable reference measurements; the Form C design delivers stable seating and handling for medium-size components. Order the ring directly via Metav Werkzeuge or consult our specialists for specification matching and delivery from Emmerich. M313.200 Setting ring, 200 mm — hardened gauge steel (Form C) A Setting ring 200 mm for reference checks and calibration of medium-size components in inspection rooms and workshop environments. Form C construction for stable handling Hardened and lapped gauge steel Diameter 200 mm for medium-size components Conforms to DIN 2250 / DIN 286, JS 3 Precision reference for production control The M313.200 is engineered as a precision setting ring that serves as a stable reference for ring gauges, go/no-go checks and calibration routines. Manufactured from hardened and lapped gauge steel, the component provides consistent surface quality and roundness, which reduces measurement scatter during repeat checks. The compliance with DIN 2250 and DIN 286 in tolerance JS 3 ensures the ring fits established inspection workflows and traceability chains, supporting reproducible results across production batches. Practical benefits in the inspection bench The ring’s 200 mm diameter and Form C geometry balance reach and rigidity for medium-format parts such as housings, flanges and coupling components. At a mass of 10.2 kg, the unit remains manageable for bench use while offering the mass stability that helps resist accidental deformation during handling. As a hardened, lapped reference, it reduces the frequency of ad hoc rechecks, streamlining process control and saving inspection time over repetitive gauging tasks. Robust specification that integrates easily Designed to match industrial practice, the ring is identified by its article code and GTIN for inventory and calibration records. The finished surface and dimensional stability make it suitable for workshop metrology, quality assurance loops and setting devices where a repeatable datum is required. The Form C arrangement supports secure seating in fixtures and minimises wobble during rotation checks, contributing to lower measurement uncertainty in routine checks. For detailed specification matching and delivery from Emmerich, contact Metav Werkzeuge for an individual consultation and ordering guidance. Technical data Article number: M313.200 GTIN: 4054469121277 Manufacturer: Metav IndustryLine Facts Diameter: 200 mm Weight: 10.2 kg eCl@ss: 21170104 Tariff number: 90173000 Special features Material: hardened and lapped gauge steel Form: Form C Standards: DIN 2250 and DIN 286, tolerance JS 3 FAQ What is the intended use of this setting ring? The setting ring is intended as a reference and calibration ring for medium-size components; it supports ring gauging, setting routines and dimensional checks in inspection and production. Which material and finish does the ring have? The ring is made from hardened and lapped gauge steel, providing a stable surface finish suitable for repeatable metrology tasks. Does the ring comply with industry standards? Yes, the component conforms to DIN 2250 and DIN 286 with tolerance class JS 3, ensuring compatibility with standard inspection procedures. How should the weight and handling be considered on the inspection bench? With a weight of 10.2 kg, the ring benefits from mass-related stability; safe handling requires appropriate support and two-person handling for prolonged repositioning. Can this ring be used to set calipers or ring gauges? The ring is suitable as a setting reference for calipers, ring gauges and similar measuring devices where a stable, standardised diameter is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com