Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
25mm Limit Gauge Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of the combination of standardised verification, hardened gauge steel construction and workshop-ready accuracy for reliable bore inspection. Benefit from rapid go/no-go checks to reduce rework and keep production moving. Order the gauge directly via Metav Werkzeuge or contact the consultants for application advice. Limit plug gauge M314.025 — 25.00 mm H7, DIN 2245, hardened gauge steel (Metav IndustryLine) The Limit plug gauge M314.025 is a hardened, DIN 2245-compliant plug gauge designed for fast verification of 25.00 mm bores to H7 tolerance in production, inspection and incoming goods control. *DIN 2245 standard for plug gauges *H7 tolerance for 25.00 mm verification *Hardened gauge steel, precision ground *Metav IndustryLine: workshop-ready accuracy Consistent acceptance testing to lower scrap rates The gauge is intended for swift, repeatable go/no-go checks that streamline inspection routines and reduce uncertainty on the shop floor. Made to the DIN 2245 specification and set for H7 verification at 25.00 mm, the instrument enables immediate decisions during batch runs and setup checks. Using a purpose-built limit plug for acceptance testing shortens cycle times compared with measurement on CMMs for routine pass/fail assessments, which helps to maintain throughput without sacrificing traceability. Robust construction for long service life Manufactured from hardened gauge steel and precision ground, the device is optimised for wear resistance and dimensional stability under repeated handling. The hardened surface and grinding process ensure that the functional diameters remain within tolerance for extended intervals, reducing the need for frequent regrinding or replacement. The solid construction supports reliable mating with standard bore seats and contributes to consistent tactile feedback during go/no-go verification. Clear role in quality systems and traceability Compliance with DIN 2245 places the gauge directly within established metrology regimes and simplifies documentation in inspection protocols. The clear design and standard tolerance class make the gauge suitable for inclusion in ISO-aligned quality procedures, offering a traceable method for conformity checks. Where process control relies on rapid discrimination between acceptable and non‑conforming parts, a standardised limit plug provides an objective, reproducible verdict that complements dimensional sampling plans. Practical workshop use and application areas This plug gauge is appropriate for machine shops, tool rooms and incoming goods inspection where round hole tolerances around 25 mm are frequent. Its uncomplicated go/no-go function supports fast cycle checks during set-up, first-piece inspection or production sampling. The device is particularly useful where interchangeability and straightforward evidence of conformity are required, such as in hydraulic component manufacture, bearing seat production or general mechanical assembly. Contact Metav Werkzeuge today to discuss how the M314.025 limit plug gauge from Metav IndustryLine fits into existing inspection routines and to arrange rapid delivery from Emmerich Technical data Article number: M314.025 GTIN: 4054469121543 ECLASS: 21170218 TARIC: 90173000 Facts Diameter: 25 mm Standard: DIN 2245 Tolerance class: H7 Material: gauge steel, hardened SKU: M314.025 Special features Precision ground functional diameters Designed for go/no-go acceptance checks Suitable for production and incoming inspection Metav IndustryLine quality FAQ What tolerance and diameter does this plug gauge verify? The limit plug gauge M314.025 verifies a 25.00 mm bore to H7 tolerance in accordance with DIN 2245; it is intended for go/no-go acceptance testing. Which material is the gauge made from and why is that important? The gauge is produced from hardened gauge steel, hardened, which provides wear resistance and dimensional stability so that the functional diameters remain consistent under repeated use. Is the M314.025 suitable for production floor checks? Yes, the M314.025 from Metav IndustryLine is designed for fast workshop use, enabling rapid pass/fail checks during setup, sampling or incoming goods inspection. How does DIN 2245 compliance benefit inspection documentation? DIN 2245 compliance simplifies integration into quality systems by providing a recognised standard for limit plug design and tolerance classes, aiding traceability and procedural consistency. Can the gauge be used for interchangeable parts and assembly checks? The plug gauge is suitable for verification tasks where interchangeability is required, such as bearing seats and hydraulic components, offering a clear go/no-go decision. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Setting Ring Hardened Gauge Steel DIN 2250, DIN 286/JS3 - Metav IndustryLine
Data inconsistency detected in the product record for SKU M313.025. The product label specifies DIN 2250 and a mass of 0.18 kg, whereas the norm field lists DIN 286 and JS3 and the weight field gives 0.4 kg. These conflicting entries affect essential technical specifications (applicable standard and nominal mass) and therefore prevent reliable product description or classification. Such discrepancies can lead to confusion in product identification and hinder accurate communication with stakeholders. Please verify which DIN standard applies and confirm the correct mass before publishing or producing marketing material. Once the authoritative values are provided, a full, standards‑compliant product description can be generated for Metav IndustryLine.
26mm Limit Go Gauge, H7 Fit, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of hardened gauge steel and DIN 2245 H7 conformity for fast, repeatable pass/fail checks of 26.0 mm bores; the robust design ensures long service life and stable measurement performance. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Limit plug gauge M314.026 – 26.0 mm H7, DIN 2245 (Metav IndustryLine) A limit plug gauge for quick verification of 26.0 mm holes to H7 tolerance, designed for workshop and inspection environments according to DIN 2245. Hardened gauge steel construction DIN 2245 H7 tolerance for hole checks Precision-ground cylindrical gauge surface Fast, standards-based pass/fail inspection The M314.026 limit plug gauge is engineered for immediate go/no-go assessment of bores at 26.0 mm nominal diameter and H7 tolerance under DIN 2245. By using a dedicated plug gauge instead of measuring instruments for every check, inspection cycles are shortened and throughput increases. The standardised dimensions guarantee compatibility with common inspection procedures and ensure traceable acceptance criteria when documenting production runs. Robust material and machining for long-term reliability Manufactured from hardened gauge steel, the cylindrical surface is precision-ground to maintain form and roundness during repeated handling. This wear-resistant construction reduces the need for frequent replacement and sustains reliable pass/fail performance over many cycles. The finished surface minimises scoring of mating parts and supports reproducible contact conditions, which is essential for consistent qualitative inspection rather than dimensional reporting. Practical benefits in the workshop and inspection room Designed for straightforward use in quality control, the cylindrical gauge requires no complex setup: insertion into the bore provides an immediate clarity of result. The compact tool supports efficient inspection flows and reduces operator time per check, contributing to smoother production processes. Combined with Metav’s broad product range and advisory service, this gauge integrates into a larger inspection strategy that favours speed, repeatability and conformity to recognised standards. For DIN-compliant, durable plug gauges from Metav IndustryLine and personalised advice on integrating this limit plug gauge into inspection routines, contact Metav Werkzeuge for availability and expert guidance. Technical data Article number: M314.026 GTIN: 4054469121550 Manufacturer: Metav IndustryLine Material: gauge steel, hardened Standard: DIN 2245 Facts Diameter: 26.0 mm Tolerance: H7 Customs tariff number: 90173000 ECLASS: 21170218 Special features Precision-ground cylindrical surface Intended for pass/fail hole inspection Category: Messstifte; Lehren SKU: M314.026 FAQ What is the intended use of this limit plug gauge? The limit plug gauge M314.026 is intended for rapid go/no-go verification of 26.0 mm bores to H7 tolerance, providing a clear pass or fail result for production and incoming inspection. Which standard does the gauge comply with? This plug gauge conforms to DIN 2245, ensuring standardised dimensions and acceptance criteria suitable for workshop inspection and quality control. What material is the gauge made from and why does that matter? The gauge is made from hardened gauge steel, which offers wear resistance and dimensional stability so that the inspection result remains reliable over many cycles. How is repeatability supported by this tool? Repeatability is supported by the precision-ground surface and hardened construction, which reduce wear and maintain contact geometry for consistent pass/fail outcomes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
26mm Setting Ring Form C Hardened Gauge Steel DIN 2250, DIN 286 JS3 - Metav IndustryLine
Take advantage of a compact, standard‑compliant gauge that combines hardened and lapped gauge steel, precise DIN 2250 / DIN 286 tolerances and a compact 26 mm diameter for reliable setting and calibration tasks; order the setting ring directly via Metav Werkzeuge or ask our consultants if needed. Setting ring 26 mm — hardened gauge steel, DIN 2250 (Metav IndustryLine) The setting ring 26 mm is a hardened ring gauge for precise calibration and setting tasks in workshop metrology, designed to provide a stable reference according to DIN standards. DIN 2250 / DIN 286, tolerance JS 3 Hardened and lapped gauge steel Diameter 26 mm for precise setting Form C geometry for standard fittings Precise reference for setup and inspection A compact, standardised ring provides a repeatable reference when setting measuring instruments or checking bore gauges. The hardened gauge steel body with a lapped finish offers low surface roughness and consistent contact conditions, which reduces variability in successive settings. Compliance with DIN 2250 and DIN 286 together with the JS 3 tolerance class ensures interchangeability with other standard parts and predictable performance in production and QA tasks. Material and manufacturing that reduce uncertainty Manufactured from hardened and lapped gauge steel, the component resists wear and retains its form even under regular workshop use. The lapped bearing surfaces minimise micro‑asperities, increasing measurement stability and lowering abrasion on mating tools. This results in fewer adjustments over time and improved process reliability when used as a bench reference or in fixture set‑up. Designed for efficient integration into workflows The compact 26 mm diameter and Form C geometry suit common holder types and reference fixtures, making the item straightforward to incorporate into existing inspection routines. As a standardised gauge, it supports quick, rational calibration steps that save set‑up time and help maintain traceable control over recurring production checks. The robust design supports frequent handling without loss of functional accuracy. Choose the Metav IndustryLine 26 mm setting ring for workshop‑grade, standard‑conforming references — contact Metav Werkzeuge for product advice and reliable delivery from Emmerich. Technical data Article number: M313.026 GTIN: 4054469120645 ECLASS: 21170104 Facts Diameter: 26 mm Tariff number: 90173000 Special features Material: gauge steel, hardened and lapped Standards: DIN 2250 and DIN 286, JS 3 Form: C Categories: Measuring pins; Gauges FAQ What tolerance class does the ring conform to? The 26 mm setting ring meets the JS 3 tolerance class as specified under DIN 2250 and DIN 286, ensuring dimensional interchangeability. Is the ring suitable for routine workshop calibration? Yes. The hardened and lapped gauge steel construction makes the ring appropriate as a routine reference for setting micrometers, bore gauges and other dial or electronic comparators. Which product designation and SKU identify this item? This item is supplied as the Metav IndustryLine setting ring 26 mm, SKU M313.026. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
27 mm Limit Go/No-Go Plug Gauge H7 Hardened Gauge Steel DIN 2245 - Metav IndustryLine
Data inconsistency detected in the supplied product information that prevents generation of a reliable product description. The entry lists two different weights for the same item (one source states 0.28 kg while another indicates 0.6 kg), and the quality/status indicators are contradictory, showing both a rejected/scrap status and a good/acceptable status simultaneously. These inconsistencies affect core attributes essential for classification and buyer guidance and must be resolved before a compliant, accurate technical and marketing text can be produced. Please supply corrected, consistent values for the item's mass and its quality/state, and confirm any other relevant technical fields. Once the conflicting data have been clarified, a full British English product description—including compliant technical data, benefit-led copy and the required manufacturer details—will be provided promptly. If assistance is needed to review the dataset, contact info@metav-werkzeuge.com for guidance.
275mm Setting Ring Form C Hardened Gauge Steel DIN 2250 / DIN 286 JS4 - Metav IndustryLine
Robust metrology for reliable setup and inspection: the combination of hardened, lapped gauge steel, DIN conformity and a true 275 mm diameter gives a stable reference for workshop and shop‑floor quality control. Order the setting ring directly via Metav Werkzeuge or ask our consultants if needed. Setting ring 275 mm — hardened & lapped gauge steel (Metav IndustryLine) The Setting ring 275 mm is a precision master ring for setting, go/no‑go checking and calibration tasks in metrology and workshop inspection. Hardened, lapped gauge steel Diameter 275 mm Form C geometry DIN 2250 / DIN 286 JS4 compliant Stability that shortens setup time A stable reference reduces repeat measurements and set‑up adjustments. The heavy, machined body of this master ring provides a consistent datum across repeated cycles: the 275 mm internal diameter is produced in hardened, lapped gauge steel, which limits wear and preserves the reference form. For machine shops and inspection benches this means fewer rechecks, quicker fixture alignment and a measurable reduction in process downtime. The solid construction (approx. 11.15 kg) also dampens handling variation, improving reproducibility during manual checks. Precision produced to recognised standards Traceable geometry is essential for trustworthy checks. The component is manufactured to DIN 2250 and DIN 286, JS4 tolerances, ensuring the ring meets established industry limits for roundness and dimension. Compliance with these norms means the part can serve as a master for setting instruments and verifying measuring equipment against an accepted standard. The lapped finish delivers a fine surface that supports accurate contact measurement without introducing local deformation. Practical design for workshop use Form C geometry keeps the ring accessible for gauges and setting fixtures while maintaining rigidity where it matters. The hardened and lapped material resists abrasion from frequent use, so the ring remains a dependable reference over long service intervals. Its mass and profile are balanced to allow safe handling by one or two technicians and to sit stably on plates or in soft jaws during verification tasks. Where repeatability and durability are priorities, this configuration offers a sound compromise between portability and long‑term stability. What this delivers to quality management Using a certified, robust master ring simplifies audit preparation and daily quality routines: fewer measurement deviations, clearer pass/fail decisions and a reduced need for corrective rework. The ring functions as a direct setting aid for workholding, a go/no‑go master for assembly control and a calibration artefact for shop‑floor gauges. Choosing a Metav IndustryLine master ensures the reference part is supported by a supplier experienced in scaling industrial metrology to everyday workshop needs. Contact Metav Werkzeuge in Emmerich for specification advice and delivery details — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss how this setting ring fits existing inspection workflows Technical data SKU: M313.275 GTIN: 4054469121291 Tariff number: 90173000 Brand: Metav IndustryLine Product: Setting ring 275 mm Facts Diameter: 275 mm Weight: 11.15 kg ECLASS: 21170104 Special features Material: hardened and lapped gauge steel Geometry: Form C Standards: DIN 2250; DIN 286, JS4 Category: Gauges / Setting rings FAQ What is the primary use of this setting ring? The setting ring 275 mm serves as a master reference for setting fixtures, performing go/no‑go checks and verifying measuring instruments in workshop and inspection environments. Which standards does the ring conform to and what does that mean? The ring conforms to DIN 2250 and DIN 286, JS4, which define dimensional and tolerance requirements for ring gauges; this ensures the ring can be used as a traceable workshop reference. Is the material suitable for frequent contact measurements? Yes — the hardened and lapped gauge steel construction is designed to resist wear from repeated contact, maintaining dimensional stability over prolonged use. How should the ring be handled and stored to preserve accuracy? Handle the ring on stable, clean surfaces and avoid impacts; when not in use, store in a dry, dust‑free area on a padded support to protect the lapped surface and preserve the reference form. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
27mm Setting Ring Form C Hardened Gauge Steel DIN 2250, DIN 286 JS 3 - Metav IndustryLine
Take advantage of the combination of DIN 2250 conformity, hardened and lapped gauge steel, and a precise 27 mm diameter to ensure repeatable set-ups and efficient inspection workflows; order directly via Metav Werkzeuge or consult our specialists for application advice. Setting ring 27 mm (M313.027) — hardened, lapped ring gauge for precision set-ups A setting ring 27 mm intended as a stable reference gauge for setting internal measuring instruments and verifying go/no-go conditions in workshop and inspection environments. Hardened, lapped gauge steel Diameter 27 mm, precision reference Conforms to DIN 2250 and DIN 286, JS 3 Form C design for stable seating Consistent reference for repeatable set-ups This ring gauge is manufactured to serve as a stable reference when setting internal micrometres and comparative measuring instruments. Compliance with DIN 2250 and DIN 286 ensures that the component sits within defined tolerance limits, while the JS 3 tolerance grade signals a fine, symmetric tolerance suitable for calibration benches and quality-control stations. The 27 mm nominal size provides a compact, easy-to-handle master that supports fast, reproducible instrument set-ups and reduces cumulative measurement uncertainty. Durable design that supports daily workshop use Made from hardened and lapped gauge steel, the part resists wear from frequent contact with measuring anvils and spindles; the lapping process yields a carefully finished contact surface that minimises distortion at the measurement interface. The Form C geometry promotes secure seating in holders and gauges, improving stability during repetitive procedures. These design choices translate into fewer rechecks, longer service intervals and reliable behaviour under standard industrial handling. Specification-driven confidence for quality control The standards and finishing applied to this gauge give quality engineers a verifiable baseline for dimensional control. The JS 3 indication denotes a narrow tolerance band appropriate for fine inspection tasks, making the component suitable as a master for comparative checking and for initial calibration routines. Traceable identification such as the GTIN supports inventory and audit processes in controlled environments, while the compact diameter simplifies storage and rapid deployment on the shop floor. Integrates smoothly into inspection workflows Thanks to its compact size and robust finishing, this ring gauge is straightforward to integrate into existing inspection processes, where space, ease of handling and repeatability matter. The component functions as a quick-reference master for setting internal measuring devices or checking fixture alignment, helping to maintain throughput without sacrificing accuracy. Backed by Metav IndustryLine's quality control, the gauge supports the aim of making high-precision measurement accessible across workshops and small production lines. Contact Metav Werkzeuge today to arrange delivery of the Metav IndustryLine setting ring M313.027 or to request detailed application guidance from our Emmerich-based specialists Technical Data Article number: M313.027 GTIN: 4054469120652 Manufacturer: Metav IndustryLine eClass: 21170104 Core technical data Diameter: 27 mm Norm: DIN 2250; DIN 286; JS 3 Customs tariff number: 90173000 Special features Material: hardened and lapped gauge steel Design: Form C Label: setting ring 27 mm, DIN 2250 FAQ Is this setting ring suitable for use as a master for internal micrometre set-up? Yes. The setting ring is produced to DIN 2250 and provides a precise 27 mm reference suitable for setting internal measuring instruments and comparative checks. What does the JS 3 tolerance mean for inspection work? The JS 3 grade indicates a fine, symmetric tolerance band that is appropriate for calibration and consistent quality-control tasks where repeatability is required. How is the surface finish achieved and why does it matter? The component is lapped, which produces a smooth, wear-resistant contact face; this finishing reduces measurement variation at the interface and prolongs reliable service life. Can this ring gauge be used in daily shop-floor routines? Yes. The combination of hardened gauge steel and a practical Form C design makes the ring robust enough for routine use while remaining easy to handle during frequent set-ups. What identification is provided for inventory and traceability? The item carries a GTIN and a clear article number (M313.027) to support traceability, stock management and audit requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
28 mm Limit Go/No-Go Plug Gauge H7 Hardened Gauge Steel DIN 2245 - Metav IndustryLine
The supplied product data contains contradictory quality information: the item is simultaneously marked as both acceptable and as scrap. This inconsistency creates confusion and prevents the generation of a reliable and accurate product description. Without clarity on the item's actual quality status, it is impossible to produce a complete, standards-compliant product text that meets the necessary requirements. To resolve this issue, please review and correct the conflicting quality indicators in the data. Once the revised and consistent information is provided, a detailed and accurate product description can be generated to ensure compliance with relevant standards and expectations.
28mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of a compact 28 mm setting ring that conforms to DIN 2250 and DIN 286 with a JS 3 tolerance; the hardened and lapped gauge steel construction ensures repeatable reference values for workshop calibration tasks. Order directly via Metav Werkzeuge or consult our specialists for application advice. Setting ring 28 mm — hardened gauge-steel reference (Form C) The 28 mm setting ring serves as a stable master for setting and checking internal-measurement tools in workshop and inspection environments, designed for use where a compact, traceable reference is required. Ring gauge, DIN 2250, JS 3 tolerance Hardened and lapped gauge steel Form C seating for standard fixtures Diameter 28 mm for compact reference Reference-grade accuracy for reliable setups The ring provides a defined reference that supports consistent setting of internal gauges and comparative instruments. Manufactured to DIN 2250 and DIN 286 and delivered within the JS 3 tolerance band, this component functions as a stable reference that reduces setup variation and speeds recurring measurement tasks. The normative conformity provides measurable evidence for quality processes and simplifies documentation in production and inspection routines. Durable construction for long-term repeatability Made from hardened and lapped gauge steel, the ring is finished to resist wear while presenting a true seating surface for tools and fixtures. The Form C geometry assists with consistent locating in common gauge fixtures, which in turn helps to maintain repeatable contact conditions and reduces influence from operator handling. The metallurgical finish and lapping process lower the risk of localised scoring and preserve the master dimension over many cycles, meaning fewer replacements and more stable control limits in the long term. Practical integration and traceability in the workshop Small and compact, this 28 mm reference element fits neatly into standard calibre setups and bench fixtures where space is limited. The article is listed under SKU M313.028 and identified by GTIN 4054469120669, supporting traceable supply-chain documentation and inventory control. As a compact master, it is particularly suited to calibration benches and assembly stations that require quick, repeatable setting of bore gauges and internal comparators, helping to shorten machine downtimes and streamline inspection sequences. For dependable master references choose the Metav IndustryLine setting ring — contact Metav Werkzeuge for ordering and application guidance from the Emmerich quality team. Technical Data Article number: M313.028 GTIN: 4054469120669 eClass: 21170104 Tariff number: 90173000 Facts Diameter: 28 mm Tolerance class: JS 3 Standards: DIN 2250, DIN 286 Special features Material: hardened and lapped gauge steel Design: Form C Category: Lehren / setting gauges FAQ What tolerance can be expected from this setting ring? The Metav IndustryLine setting ring M313.028 is manufactured to JS 3 tolerance in accordance with DIN 2250, offering a standardised fit for reference applications. Which material is the ring made from and why does it matter? The ring is made from hardened and lapped gauge steel, which provides wear resistance and a stable seating surface, ensuring long-term repeatability for master-reference uses. Can the ring be used to set internal bore gauges and comparators? Yes; the 28 mm ring gauge is intended as a compact reference for setting internal-measurement tools such as bore gauges and internal comparators. What does Form C indicate for this product? Form C refers to the seating and shoulder geometry, which is compatible with common fixture designs and supports reproducible locating during repeated set-ups. How is the product identified for traceability and inventory? This setting ring is sold as SKU M313.028 and carries GTIN 4054469120669 for supply-chain traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
29 mm Go/No-Go Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of a DIN 2245‑compliant inspection tool delivered in hardened gauge steel with precise H7 tolerance for consistent pass/fail decisions; order via Metav Werkzeuge or consult the technical team for application advice. Limit plug gauge 29.0 mm H7 (DIN 2245) by Metav IndustryLine — hardened gauge steel, inspection fit The limit plug gauge 29.0 mm H7 (DIN 2245) offers a compact, rugged solution for go/no‑go inspection of bores and cylindrical fits in production and incoming inspection. DIN 2245 compliant plug gauge H7 Hardened gauge steel for durability SKU M314.029, GTIN 4054469121581 Reliable, standards‑based gauging for production control This gauge is designed for clear, repeatable assessment of bore conformity: the H7 tolerance and DIN 2245 standardisation ensure that the part either meets the specified fit or is rejected instantly, reducing subjective judgement on the shop floor. Manufactured from hardened gauge steel, the instrument maintains dimensional stability under normal workshop conditions, guaranteeing consistent accuracy during frequent use. The compact cylindrical form allows straightforward application in inspection benches and mobile quality checks without complex fixturing. Durable construction that minimises downtime Constructed from hardened gauge steel, the gauge resists wear and abrasion, extending service intervals and preserving the test limit. This durability translates into fewer replacements and predictable maintenance cycles for the quality department. The simple, no‑adjustment design of a limit plug gauge means immediate usability and minimal handling training for operators, while the robust material choice preserves the defined gauging surface so that the interchangeability of mating parts remains verifiable throughout production runs. Traceable itemisation for quality systems and stock control The item is supplied with identifiers for efficient traceability in inventory and quality records: SKU M314.029 and GTIN 4054469121581 support barcode systems and ERP entries. Compliance with DIN 2245 facilitates acceptance in supplier quality plans and inspection protocols, helping to lower scrap rates and rework by detecting nonconforming bores early. The gauge suits routines in incoming inspection, process control and final checks where clear pass/fail decisions are required and documentation of measured conformity is essential. For application advice or to request technical specifications for the Metav IndustryLine limit plug gauge M314.029, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific bore tolerances and production environments Technical Data Article number: M314.029 GTIN: 4054469121581 Tariff code: 90173000 Facts Diameter: 29 mm Material: gauge steel, hardened Standard: DIN 2245 Special features Tolerance: H7 (limit plug gauge) Category: plug gauges / measuring pins / gauges Brand: Metav IndustryLine FAQ What is the intended use of this plug gauge? The limit plug gauge is used for pass/fail inspection of bores to confirm conformity with the specified H7 fit; it serves in production control and incoming inspection routines. Which standard does the gauge follow? The instrument is manufactured to DIN 2245 and designed to verify cylindrical bore tolerances consistent with that standard. What material is the gauge made from and why does it matter? The gauge is made from hardened gauge steel to provide wear resistance and dimensional stability, maintaining accurate go/no‑go assessment over time. How is the item identified for stock and traceability? Inventory and quality systems can reference SKU M314.029 and GTIN 4054469121581 for ordering, traceability and documentation. Can this gauge be used for interchangeability checks in assembly? Yes, the limit plug gauge supports interchangeability checks by quickly validating that a bore meets the H7 specification required for mating components. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
29mm Setting Ring Form C Hardened Gauge Steel DIN 2250, JS3 - Metav IndustryLine
Take advantage of a compact, standards‑compliant gauge that combines repeatable dimensional accuracy and robust wear resistance for routine calibration and setting tasks. Order the setting ring directly via Metav Werkzeuge or consult the Metav team for specification advice. Setting ring M313.029 — 29 mm setting ring, hardened and lapped gauge steel Setting ring M313.029 is a precision ring gauge designed for setting and checking measuring instruments and go/no‑go fixtures in workshop and inspection environments. 29 mm nominal diameter gauge Hardened, lapped gauge steel Conforms to DIN 2250 / DIN 286 Form C seating for secure location Precision where it matters: consistent reference for gauges and fixtures The 29 mm setting ring serves as a stable reference for adjusting micrometres, comparators and dial gauges. Manufactured from hardened and lapped gauge steel, its contact faces present a low‑wear surface that preserves dimensional integrity over repeated use. Conformity to DIN 2250 together with the DIN 286, JS 3 tolerance class provides a clear, certified performance level for quality control routines, reducing uncertainty in adjustment tasks and ensuring interchangeability between instruments. Designed for practical workshop use and fast seating The Form C geometry gives reliable seating and quick engagement in common holding systems and fixture designs. Its compact form factor and robust finish make it suitable for frequent handling in production or calibration labs, where ease of seating and stability under manual or light mechanical engagement improve throughput. The lapping process applied to the ring’s measuring face minimises surface roughness and micro‑asperities, which in turn reduces measurement scatter during repeated set‑ups. Built to standards: clear traceability and inspection confidence As an engineered gauge produced for metrological use, the ring aligns with established inspection protocols: the JS 3 tolerance band ensures predictable deviation margins when compared to nominal size, simplifying pass/fail assessments and documentation. The use of recognised standards supports traceable measurement chains and helps meet internal and customer audit requirements, contributing to efficient quality assurance processes. Material and durability: low maintenance, long service life Constructed from gauge steel, hardened and lapped, the ring offers a balance of wear resistance and machinability that suits frequent calibration cycles. The finish minimises corrosion risk in typical workshop atmospheres and reduces the need for frequent rework; when handled correctly and stored with basic care, the component maintains its metrological properties, reducing lifecycle costs and downtime. Contact Metav Werkzeuge for ordering and technical consultation — Metav’s precision filter in Emmerich ensures fast supply and expert guidance for integration into existing quality processes (+49 2822 7131930, info@metav-werkzeuge.com) Technical Data SKU: M313.029 GTIN: 4054469120676 ECLASS: 21170104 Tariff number: 90173000 Facts Nominal diameter: 29 mm Standards: DIN 2250; DIN 286, JS 3 Material: hardened, lapped gauge steel Geometry: Form C Special features Suitable for instrument setting and gauge checking Low‑wear lapped measuring faces Workshop and calibration lab use Category: Gauges / Setting rings FAQ What tolerance class does this setting ring meet? The setting ring meets the DIN 286, JS 3 tolerance class and is produced to the DIN 2250 guideline for ring gauges. Is this ring suitable for repeated use in a production environment? Yes, the ring’s hardened and lapped gauge steel construction is selected for durability and stable performance under frequent handling in workshop and inspection settings. Which equipment can be set with this ring gauge? The 29 mm setting ring is intended for setting micrometres, dial indicators and other dimensional reference instruments where a precise nominal diameter reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2mm Tapered Feeler Gauge Set 21 Pieces 0.05–2.00mm Increments, Special Steel, Factory Standard - Metav IndustryLine
Take advantage of compact precision and robust construction for consistent gap control: a blades range from 0.05–2.00 mm, special steel construction and factory conformity ensure reliable measurement results — order directly via Metav Werkzeuge or contact our consultants for application advice. Feeler gauge set M318.011 by Metav IndustryLine — 0.05–2.00 mm range, special steel the feeler gauge set M318.011 is a compact folding gauge set designed for precise gap measurement and adjustment tasks in workshop and maintenance environments 0.05–2.00 mm measuring range 21 precision blades in stepped sizes Special steel for durable edge retention Compact folding design for safe storage Precise dimension control that reduces rework Accurate gap specification and repeatable thickness checks are essential for maintenance, assembly and quality inspection. With a measuring range from 0.05–2.00 mm and stepped blade graduations, this folding gauge set delivers fine resolution across common clearance requirements. The manufacturer standard (Werksnorm) underpins reproducible blade thicknesses and contributes to consistent process control. Built for frequent use on the shop floor, the set supports quick verification of valve clearances, shim selection and joint gaps, reducing the time spent on iterative adjustments and lowering the risk of component rejects. The combination of a compact profile and robust blade geometry promotes straightforward insertion into narrow clearances while maintaining dimensional stability. Robust material and handling for everyday workshop use Manufactured from special steel, the blades offer high wear resistance and good edge retention, which keeps calibration drift to a minimum under regular operation. The folding mechanism protects individual blades from damage and contamination during transport and storage, extending working life and preserving measurement integrity. Lightweight design and a low storage profile help integrate the gauge into a technician’s toolkit without adding significant bulk. Where speed and reliability matter, the durable construction supports repeated use, making routine measurement tasks more efficient and less error-prone. Practical application benefits and suitability Intended for mechanical workshops, maintenance departments and production inspection, this gauge set covers typical clearance and shim tasks across engines, gearboxes and assembly operations. The stepped thickness progression allows rapid identification of the correct blade for a specified gap, which speeds adjustment work and reduces machine downtime. The set’s accuracy specification supports consistent quality checks during incoming inspection and during service intervals. The straightforward, analogue nature of the tool means no batteries or electronics are required, ensuring dependable performance in harsh or constrained environments. What is contained and how traceability is assured The set comprises blades covering the full 0.05–2.00 mm spectrum in incremental steps, supplied as a folding assembly for secure organisation and easy selection. A clear article number and GTIN provide traceability for stock and quality records, and the product is produced to the stated Werksnorm to maintain dimensional conformity. For businesses that document tool inventories or need consistent replacement parts, the standardised blade sizing simplifies procurement and ensures compatibility across tasks without the need for frequent recalibration. Contact Metav Werkzeuge for tailored application guidance and to order the Metav IndustryLine feeler gauge set M318.011 for reliable workshop gap measurement Technical data Article number: M318.011 GTIN: 4054469127644 Material: Special steel Standard: Werksnorm Facts Measuring range: 0.05–2.00 mm Accuracy: 0.012 mm Length: 100 mm Weight: 0.02 kg Special features Set: Yes Pieces per set: 21 Blades: stepped sizes from 0.05 to 2.00 mm Category: Feeler gauges / Gauges FAQ What thickness range do the blades cover? The Metav IndustryLine feeler gauge set M318.011 covers the thickness spectrum from 0.05 mm up to 2.00 mm in stepped sizes, enabling checks across common clearance requirements. Is the material suited to workshop environments? Yes — the blades are made of special steel, chosen for wear resistance and edge stability, which makes the set suitable for regular workshop and maintenance use. Can this set be used for engine valve clearances and shim selection? The folding gauge assembly is well suited to tasks such as valve clearance measurement and shim selection; its stepped thicknesses simplify rapid identification of the required gap thickness. How is traceability provided for quality records? The product is supplied with a clear article number and GTIN for inventory and traceability; production follows the stated Werksnorm to maintain dimensional conformity. Does the gauge require batteries or calibration equipment? No electronics are involved; the analogue blades do not require batteries. Calibration is not electronically dependent — traceability is managed via manufacturing standards and identifiers. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2–3mm Ceramic Gauge Pin Set 0.01mm Steps, Stainless ZrO2 Precision ±0.0015mm, Plastic Case - Metav IndustryLine
Combining sub‑micron repeatability, HV 1250 surface hardness and zirconia wear resistance yields a reliable gauge for precision inspection and alignment tasks; ideal for workshop use and long series checks. Order the Ceramic test pin set directly via Metav Werkzeuge or ask our consultants if needed. Ceramic test pin set — 101-piece (2.00–3.00 mm, 0.01 mm increment) by Metav IndustryLine The Ceramic test pin set is a workshop-grade gauge kit for accurate inspection, bore gauging and fixture set‑up in production and metrology environments. Zirconia ceramic, corrosion-resistant Accuracy < ±0.0015 mm per pin 0.01 mm increment for fine grading Supplied with holder in plastic case Precision where small differences matter The set delivers exceptional dimensional fidelity thanks to a declared accuracy of < ±0.0015 mm and a fine 0.01 mm step between pins. Packs of graduated pins remove guesswork when matching bore sizes or verifying drilled holes, enabling faster decision‑making on the shop floor and reducing rework. The combination of tight tolerances and consistent step sizing makes these gauge pins suitable as a reference for comparative checks and for setting up plug‑gauges or test fixtures. Engineered for durability and stable measurement Manufactured from zirconia ceramic, the pins combine a wear‑resistant surface with natural anti‑magnetic behaviour; this minimises distortion and avoids magnetic interference during delicate inspection tasks. The material’s HV 1250 hardness offers long service life under repeated contact, ensuring dimensional stability across many measurement cycles. The 50 mm working length gives a good contact area while remaining easy to handle and resistant to bending. Workflow benefits and practical handling Delivered as a workshop version in a compact plastic case with a dedicated pin holder, the set is arranged for quick selection and organised storage. The step size allows technicians to perform incremental checks rapidly, and the consistent geometry simplifies the transfer of measurement data into inspection reports. Because the pins are corrosion‑resistant and anti‑magnetic, cleaning requirements are reduced and handling is straightforward even in mixed‑material environments. Where this kit improves quality control A set of finely graded gauge pins speeds up internal inspection loops and supports machine and fixture set‑ups where nominal bores between 2.00 mm and 3.00 mm must be validated. The collection is designed to function as both a verification tool for finished parts and as a quick checking aid during manufacturing runs, enhancing throughput by reducing uncertainty. With clear organisation and rugged components, the set supports consistent measurement routines and traceable checks in production environments. Contact Metav Werkzeuge for technical advice, availability and assistance procuring the Metav IndustryLine ceramic test pin set directly from Emmerich Technical data Article number: M318.592 Product name: Ceramic test pin set, 101-piece 2.00–3.00 mm, 0.01 mm Brand: Metav IndustryLine Numbers / Core technical data Measuring range: 2.00–3.00 mm Increment: 0.01 mm Set count: 101 Working length: 50 mm Hardness: HV 1250 Accuracy: < ±0.0015 mm Special features Material: zirconia ceramic Corrosion-resistant Anti-magnetic Wear-resistant surface Workshop version Supplied with pin holder Supplied in plastic case FAQ What is the measurable range covered by the set? The set covers gauges from 2.00 mm to 3.00 mm with 0.01 mm increments, allowing fine grading across that interval. Are the pins magnetic and suitable for use near sensitive electronics? No, the pins are made of zirconia ceramic and are naturally anti‑magnetic, making them suitable for environments where magnetic materials could interfere. How durable are the test pins under frequent use? The high surface hardness (HV 1250) and wear‑resistant ceramic composition ensure long service life and stable dimensions during repeated contact checks. Is the set organised for quick selection during production checks? Yes, the 101-piece collection is supplied in a compact plastic case with a pin holder to speed up selection and reduce handling time on the shop floor. Can these pins be used for calibration or as a reference standard? The set is intended for inspection and workshop gauging; when used as a reference for calibration, traceability and calibration certificates should be confirmed via the supplier for specific quality system requirements—the SKU for this set is M318.592. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2–3mm Gauge Pin Set 21pc 70mm Step 0.05mm in Case - Metav IndustryLine
Take advantage of precise diameter coverage and compact handling for fast, repeatable inspections: the 21-piece gauge pin set provides 0.05 mm steps across a 2.00–3.00 mm range and robust special-steel construction for long service life. Order the set directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin set — 21-piece, 2.00–3.00 mm, 0.05 mm graduation by Metav IndustryLine The gauge pin set offers a compact inspection solution for checking small bores, verifying drill sizes and supporting assembly alignment tasks in precision workshops. 21-piece set, 2.00–3.00 mm range 0.05 mm incremental sizing 70 mm working length per pin Durable special-steel construction Consistent diameter control for small bores The set delivers reproducible checks across the 2.00–3.00 mm window, with each step calibrated at 0.05 mm increments to simplify decision-making during inspection. Where repeatability matters, the fine gradation reduces guesswork and speeds up size verification processes; this is particularly valuable for small components, gauge checks after reaming or for first-off inspections. The slim design and uniform length ensure stable seating in bores so that precision is maintained from the first pin to the last. Robust construction for everyday workshop use Manufactured from special steel, the pins resist wear under frequent handling and maintain dimensional stability in typical workshop environments. The 70 mm working length gives a reliable reach into bores while remaining easy to manoeuvre by hand or with simple fixtures. Thanks to their solid material and consistent machining, the pins provide long-term operational value and reduce the need for frequent replacements, supporting continuous production and routine quality control. Practical set composition that speeds inspection routines Supplied as a 21-piece set, the collection covers the target diameter range in uniform steps, enabling quick selection and incremental measurement without intermediary tools. This arrangement cuts cycle time during batch inspections and makes comparative checks straightforward when validating hole tolerances or matching mating elements. The clearly graduated sequence promotes orderly workflow and reduces the chance of selection errors, so inspection results are both traceable and efficient. For procurement or tailored advice on application, contact Metav Werkzeuge — the Metav IndustryLine gauge pin set is available through our Emmerich team and our technical consultants are ready to assist. Technical data SKU: M318.822 GTIN: 4054469181943 Manufacturer: Metav IndustryLine Facts Diameter range: 2.00–3.00 mm Length: 70 mm Graduation: 0.05 mm Pieces per set: 21 Weight: 0.74 kg Special features Material: Special steel Set type: Gauge pin set Increment per pin: 0.05 mm FAQ What sizes are included in the set? The gauge pin set contains pins from 2.00 to 3.00 mm in 0.05 mm increments, covering the full 2.00–3.00 mm range for small-bore inspection. How many pins are supplied and how are they organised? This is a 21-piece set; each pin advances by 0.05 mm so systematic checks can be performed without intermediate adjustments. What material are the pins made from and what does that mean for durability? The pins are produced from special steel, which provides wear resistance and dimensional stability during repeated inspection cycles. Is this set suitable for checking drill or reamed holes in production parts? Yes, the set is designed for verifying drill and ream sizes as well as for comparative bore measurement tasks; the fine 0.05 mm steps make it suitable for routine control and set-up checks. What is the product code for ordering or referencing? Refer to the SKU M318.822 when ordering the Metav IndustryLine gauge pin set to ensure the correct 21-piece, 2.00–3.00 mm configuration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3 mm Gauge Ball Pair Chrome Steel Hardened Accuracy 0.003 mm, Tolerance 0.00008 mm - Metav IndustryLine
Combining high metrological performance with hardened material durability, this gauge ball pair delivers consistent reference values for inspection, calibration and comparator tasks. The very tight diameter tolerance and ultra‑smooth surface reduce measurement uncertainty and wear in contact applications. Order the gauge ball pair directly via Metav Werkzeuge or ask our consultants if needed. Gauge Ball Pair M318.413 — hardened chrome steel, 3 mm, 0.003 mm accuracy A Gauge Ball Pair (M318.413) for precision reference and gauging tasks in laboratory and workshop inspection settings. Hardened chrome steel (>HRC 62) Accuracy 0.003 mm for reference measurements Diameter tolerance 0.00008 mm for reproducibility Surface finish Ra 0.00001 mm for low friction Supplied as a set of two, diameter 3 mm Consistent reference values for reliable inspection These precision spheres serve as stable reference elements in inspection, comparator and setting operations where reproducibility matters. With an accuracy of 0.003 mm, the pair reduces measurement scatter when used in gauge assemblies or alongside optical comparators. The small diameter makes them suitable for fine features while the combination of tight tolerance and repeatable geometry helps to maintain process control and traceable inspection results. Durable construction and surface quality that reduce uncertainty Manufactured from hardened chrome steel, the spheres combine hardness and corrosion resistance for long service life in contact measurement tasks. The material hardness exceeds HRC 62, which, together with a diameter tolerance of 0.00008 mm and a surface finish Ra 0.00001 mm, minimises wear and variation at the contact point. These characteristics preserve reference integrity and reduce the frequency of requalification in high‑use environments. Practical use, traceability and procurement clarity Supplied as a set of two with a compact packaged weight of 0.05 kg, the spheres are easy to handle for fixture mounting, plug gauges or comparative checks. The small diameter (3 mm) makes them appropriate for micro‑gauging and detailed part inspections where space is constrained. Clear identifiers (M318.413, GTIN 4054469184012) simplify ordering and inventory management, and the robust finish ensures repeatable performance across measurement cycles. Contact Metav Werkzeuge for availability, tailored technical advice and procurement of the Metav IndustryLine gauge ball pair M318.413 with 0.003 mm accuracy Technical Data Article number: M318.413 GTIN: 4054469184012 Category: Lehren Numbers / Core technical data Diameter: 3 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Surface roughness (Ra): 0.00001 mm Weight: 0.05 kg Hardness: >HRC 62 Special features / Material and supply Material: hardened chrome steel Pack: set of two gauge balls Supplied quantity: 2 pieces Suitable for reference and gauge applications FAQ What is the nominal diameter and tolerance of these gauge balls? The pair has a nominal diameter of 3 mm with a diameter tolerance of 0.00008 mm for tight reproducibility. What level of accuracy can be expected in reference measurements? The gauge ball pair provides an accuracy of 0.003 mm, making it suitable as a stable reference element in inspection setups. Are the spheres hardened and suitable for frequent contact use? Yes, the spheres are made from hardened chrome steel with a hardness greater than HRC 62, offering wear resistance for repeated contact measurements. How are the parts supplied and what is the quantity per set? The product is supplied as a set of two gauge balls (M318.413) and is intended for use as paired reference elements. How can these spheres be integrated into workshop inspection workflows? The small 3 mm diameter and high surface quality make them suitable for fixture mounting, comparator checks and precision gauging where compact, repeatable references are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3 mm Limit Gauge Plug Gauge Wear Allowance, DIN 7162 - Filetta
Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Hardened steel construction, conformity with DIN 7162 and a deliberate wear allowance on the go side provide fast, repeatable pass/fail decisions for small-bore inspection. Combine these attributes with Metav Werkzeuge’s supply reliability to keep inspection gates closed and production flowing. Order the gauge directly via Metav Werkzeuge or ask our consultants if needed. Plug limit gauge — hardened steel, DIN 7162 (Filetta) A plug limit gauge for rapid go/no-go testing of small bores, designed to meet workshop and production inspection requirements Hardened steel for durable measurements Conforms to DIN 7162 gauge standard Wear allowance on the go side for extended service life Rapid conformity checks that streamline inspection The plug limit gauge is a compact instrument tailored for immediate acceptance testing: a straightforward go/no-go decision eliminates prolonged measurement routines and reduces throughput bottlenecks. Constructed from hardened steel, the gauge resists deformation and preserves dimensional integrity under frequent use, which increases repeatability and reduces downtime caused by ambiguous results. Conformity to DIN 7162 ensures that the gauge integrates into standardised inspection plans and supports consistent quality control documentation. Durable design that suits busy workshops Made of hardened steel and supplied with a factory-specified wear allowance on the go side, the gauge delivers long service intervals even under continuous use. The tool’s compact geometry is optimised for small-bore verification and fits into common inspection benches and gauge fixtures. This simple construction reduces maintenance effort: when the go end begins to show wear beyond the allowance, replacement or regrinding can be scheduled without unexpected production stops, preserving measurement certainty and operational uptime. Practical benefits for quality workflows Specified as a plug-type limit gauge, the tool provides clear, binary results that accelerate decision-making in incoming inspection and production control. Reduced measurement time lowers labour costs and minimises the risk of release of non-conforming parts. The item is listed under SKU MS911.204 and is suited for routine checks where standardised acceptance criteria are enforced. For procurement and integration into measurement plans, Metav Werkzeuge offers product guidance and consistent European distribution that simplifies stocking and traceability. Discuss batch supply, compatibility with existing gauge sets or integration into inspection protocols with Metav Werkzeuge for Filetta plug limit gauges Technical data Article number: MS911.204 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on the go side Numbers / Core technical data Nominal size: 3 mm Special features / Versions Gauge type: plug limit gauge (go/no-go) Intended application: small-bore inspection and acceptance testing Category: gauges / measuring pins FAQ What is a plug limit gauge used for? A plug limit gauge provides a simple go/no-go check for bore diameters; the Filetta plug limit gauge (SKU MS911.204) is intended for quick acceptance testing of small bores in production and inspection. What material is the gauge made from? The Filetta plug limit gauge is manufactured from hardened steel to ensure dimensional stability and long-term durability under regular use. What does the wear allowance on the go side mean? The wear allowance indicates a designed service margin on the go end so that measured wear can be tolerated without immediate rejection; this extends usable life while maintaining reliable pass/fail decisions. Which standard does the gauge conform to? The gauge complies with DIN 7162, making it suitable for standardised inspection routines and integration into quality control documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3 mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS 3 - Metav IndustryLine
Benefit from a compact, standards‑based reference that combines hardened, lapped gauge steel, DIN conformity and a precise 3 mm diameter to ensure repeatable set‑ups and minimal wear. Order the setting ring directly via Metav Werkzeuge or consult our technical team for application advice. Setting ring 3 mm — hardened gauge ring, DIN 2250, Metav IndustryLine Setting ring 3 mm is a small, precision gauge ring designed for setting and checking measuring equipment and fixtures in inspection and workshop environments. Form C setting ring, DIN 2250 compliant Hardened and lapped gauge steel finish Diameter 3 mm reference dimension Compact reference for workshop and inspection use Compact reference for repeatable set‑ups and calibration The compact design of this reference ring provides a stable datum for setting micrometres, gauges and other comparative instruments. Manufactured from hardened gauge steel with a lapped finish, the component resists surface deformation and retains its geometry under frequent contact. Conformity to DIN 2250 (and referenced DIN 286, JS 3 tolerance class) ensures the ring functions as a reliable small‑scale reference, reducing rework and the need for frequent replacement of cheap or soft alternatives. Precision tolerance and robust material for long service life The ring’s tolerance class JS 3 and the lapped surface mean contact variability is reduced, which translates into improved reproducibility when transferring a nominal setting to production tools. The 3 mm diameter is intended as a precise reference point for fine adjustments and comparative checks; the Form C profile enables stable seating on mating surfaces. Made from gauge steel, hardened and lapped, the part offers dimensional stability and abrasion resistance that support consistent process quality over time. Practical handling, storage and workshop integration At 0.1 kg and with a small footprint, the reference ring is easy to handle and integrate into shop‑floor routines. Its compactness makes it convenient to keep with an inspection kit or in a calibration drawer for daily checks. As a standards‑based item from Metav IndustryLine, the component supports lean workflows by shortening set‑up times and helping to avoid process stoppages caused by uncertain reference dimensions. For application guidance, batch availability or to secure this Metav IndustryLine setting ring (SKU M313.003) for production use, contact Metav Werkzeuge for tailored advice and supply options. Technical Data Article number: M313.003 GTIN: 4054469120393 Weight: 0.1 kg Diameter: 3 mm Material: Gauge steel, hardened and lapped Norms: DIN 2250; DIN 286, JS 3 Characteristic: Form C Facts eClass: 21170104 Tariff code: 90173000 Special features Hardened and lapped finish Form C profile Small, precise reference dimension FAQ What is the primary use of this setting ring? The setting ring is intended as a precision reference for setting and checking gauges and measuring tools; the Setting ring 3 mm (Metav IndustryLine, SKU M313.003) provides a stable datum for fine adjustments. Which standards does the ring meet? The component is produced to DIN 2250 specifications and referenced to DIN 286, JS 3 tolerance class, ensuring compatibility with established workshop and inspection routines. What material and surface treatment are used? The ring is manufactured from gauge steel, hardened and lapped, which offers abrasion resistance and dimensional stability for repeated contact use. Is the ring suitable for daily workshop use? Yes; the compact format and robust material make the ring well suited for regular setting tasks and short‑interval checks as part of a shop‑floor inspection kit. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3,06mm Prüfstift, ±0,001mm, Länge 50mm, Werkstatt-Ausführung - Metav IndustryLine
Nutzen Sie die Kombination aus hoher Präzision, robustem Spezial-Stahl und praktischer Transportkiste für zuverlässige Endmaße in der Werkstatt. Bestellen Sie den Prüfstift M323.306 direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Prüfstift M323.306 von Metav IndustryLine — Prüfstift für präzise Endmaße Prüfstift M323.306 eignet sich als kompaktes Kontrollmittel für Endmaßprüfungen und Qualitätssicherung in Werkstatt und Fertigung, mit klarer Eignung für präzise Messaufgaben. Prüfstift M323.306 von Metav IndustryLine Präzision ±0,001 mm Toleranz Durchmesser 3,06 mm, Länge 50 mm Werkstatt-Ausführung mit hoher Robustheit Lieferung in Kunststoff- oder Holzkiste Präzision für Endmaßkontrollen und Fertigungsprüfung Der Prüfstift bietet eine reproduzierbare Messqualität dank der angegebenen Toleranz ±0,001 mm, was ihn zu einem geeigneten Hilfsmittel für präzise Endmaßkontrollen macht. In der Praxis bedeutet das, dass wiederholte Prüfungen vergleichbare Ergebnisse liefern und Ausschuss durch fehlerhafte Maßgaben reduziert werden kann. Die kompakte Bauform ermöglicht einfaches Einsetzen in Messvorrichtungen und Prüfaufnahmen, wodurch die Effizienz an Montage- und Messplätzen steigt. Materialwahl und Langlebigkeit für den Werkstattalltag Gefertigt aus Spezial-Stahl, ist der Prüfstift auf Festigkeit und Verschleißfestigkeit ausgelegt, sodass er häufigen Handhabungszyklen in industrieller Umgebung standhält. Die Werkstatt-Ausführung betont mechanische Robustheit und sorgt für eine stabile Kontur über viele Prüfzyklen. Damit eignet sich das Produkt für wiederkehrende Qualitätsprüfungen an Bauteilen, ohne dass Formtreue oder Maßgenauigkeit schnell nachlassen. Zielgruppe und typische Anwendungen Dieser Prüfstandard richtet sich an Fertigungsingenieurinnen, Qualitätsprüfer und Werkzeugmacher, die präzise Endmaße verifizieren müssen. Typische Einsatzfelder sind die Stichprobenprüfung an Serienbauteilen, die Kontrolle von Passungen sowie die Verwendung in Messvorrichtungen zur Serienfreigabe. Durch die einfache Integration in bestehende Prüfprozesse lässt sich die Messung ohne großen Schulungsaufwand durchführen. Handhabung, Maße und Lieferung Mit einer Länge von 50 mm und einem Durchmesser von 3,06 mm ist der Prüfstift leicht handhabbar und lässt sich in Standard-Aufnahmen einfach positionieren. Das geringe Gewicht erleichtert den Transport zum Messplatz. Die Lieferung erfolgt in einer Kunststoff- oder Holzkiste, die den Transport schützt und bei größeren Werkzeugen als Transportsicherung dient; die Kiste ist primär für sicheren Versand und Transport ausgelegt. Empfehlung: Für reproduzierbare Endmaße den Metav IndustryLine Prüfstift M323.306 wählen; technische Fragen gern per eMail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 klären Produktmerkmale Artikelnummer: M323.306 Marke: Metav IndustryLine GTIN: 4061905056536 ECLASS: 21170231 Daten Länge: 50 mm Durchmesser (Messbereich): 3,06 mm Messbereich Min: 3.06 mm Messbereich Max: 3.06 mm Gewicht: 0,006 kg Genauigkeit: ±0,001 mm Besonderheiten Werkstatt-Ausführung Material: Spezial-Stahl Lieferung: Kunststoff- oder Holzkiste für Transport FAQ Wie genau ist der Prüfstift bei wiederholten Messungen? Der Prüfstift M323.306 von Metav IndustryLine bietet eine Genauigkeit von ±0,001 mm, wodurch er sich für wiederholte Endmaßprüfungen eignet und reproduzierbare Ergebnisse in der Fertigungsprüfung ermöglicht. Eignet sich der Prüfspitzen für Messvorrichtungen und Prüfaufnahmen? Ja, der Prüfstift M323.306 wurde als Werkstatt-Ausführung konzipiert und lässt sich aufgrund der Länge von 50 mm und des Durchmessers 3,06 mm problemlos in viele Messvorrichtungen einbauen. Wie wird der Prüfstift geliefert und was ist beim Transport zu beachten? Der Prüfstift wird in einer Kunststoff- oder Holzkiste geliefert, die speziell für sicheren Transport ausgelegt ist. Die Kiste schützt das Bauteil während Versand und Handling. Welche Materialeigenschaften macht der Prüfspitzen langlebig? Der Einsatz von Spezial-Stahl sorgt für hohe Festigkeit und Formstabilität des Prüfspitzen, was die Lebensdauer bei häufigem Einsatz im Werkstattalltag erhöht. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3-12mm Limit Plug Gauge Set H7, Hardened Gauge Steel, DIN 2245, Case Included - Metav IndustryLine
Take advantage of the combination of durable hardened gauge steel, a compact 3–12 mm inspection range and the clear go/no‑go decision logic for reproducible quality control. Order the limit plug gauge set directly via Metav Werkzeuge or contact the consultants for further application advice. Limit plug gauge set M314.000 – 3–12 mm, 7‑piece, DIN 2245 H7 (Metav IndustryLine) The Limit plug gauge set M314.000 is designed for quick, unambiguous bore checks in small components and fine mechanical assemblies, offering a compact solution for production and inspection tasks. Hardened gauge steel construction 7-piece set covering 3–12 mm Manufactured to DIN 2245 H7 standard Compact and lightweight at 0.35 kg Faster pass/fail checks for small bores This limit plug gauge set simplifies routine bore inspection by providing defined go/no‑go references in a compact format. The DIN 2245 H7 specification ensures that each gauge represents the intended tolerance class, enabling immediate acceptance or rejection without elaborate measuring sequences. As a result, inspection throughput improves and assembly errors are reduced, supporting efficient quality control in small‑part production. Robust materials for reliable repeatability Made from hardened gauge steel, the gauges resist wear and preserve dimensional accuracy under frequent use. This construction reduces the need for frequent reconditioning and keeps uncertainty low across multiple inspections. The total weight of 0.35 kg and the small footprint of the set make it easy to carry to the workbench or inspection station while maintaining the stability required for consistent go/no‑go readings. Practical set composition that covers common bore sizes The set contains the standard sizes 3, 4, 5, 6, 8, 10 and 12 mm, presented as a coordinated 7‑piece set to cover typical small‑bore applications in toolrooms, workshop inspection and component assembly. Having the most used diameters on hand reduces downtime and avoids the need to change measuring methods, so measurement tasks remain fast and reproducible. Choose the Metav IndustryLine limit plug gauge set for dependable, shop‑ready bore verification and contact Metav Werkzeuge for specification advice or to discuss application suitability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M314.000 GTIN: 4054469121307 ECLASS: 21170218 Measurement range: 3–12 mm Set composition: 7 pieces (3, 4, 5, 6, 8, 10, 12 mm) Weight: 0.35 kg Material: hardened gauge steel Standard: DIN 2245 Fit/tolerance: H7 Tariff number: 90173000 FAQ Which sizes are included in the set? The set includes plug gauges for 3, 4, 5, 6, 8, 10 and 12 mm to cover the most common small‑bore checks. To which standard and tolerance does the set conform? The gauges are made to DIN 2245 with an H7 tolerance class for clear go/no‑go inspection. What material are the gauges made from? The gauges are manufactured from hardened gauge steel for wear resistance and dimensional stability. How is the set intended to be used? The set serves as a limit plug gauge set for rapid pass/fail evaluation of bore diameters using the go/no‑go principle. Is this set suitable for workshop and production use? Yes, the compact range and robust construction make the set well suited to workshop inspection and small‑part production control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3-30mm Limit Plug Gauge Set 28 Pieces 1mm Increment DIN 2245 H7 Hardened Gauge Steel Plastic Case - Metav IndustryLine
Take advantage of a DIN 2245 H7 limit plug gauge set that combines precise acceptance testing, wear‑resistant hardened gauge steel, and full coverage from 3–30 mm in 1 mm steps for consistent quality control. Order the limit plug gauge set directly via Metav Werkzeuge or contact our consultants for specification support. Limit plug gauge set M314.001.1 — 3–30 mm, DIN 2245 H7 (Metav IndustryLine) A Limit plug gauge set M314.001.1 for rapid Go/No‑Go inspection of internal diameters, designed for production lines and workshop quality control to DIN 2245 standards. DIN 2245 H7 tolerance gauge set Hardened gauge steel for long life 3–30 mm in 1 mm increments Supplied in a protective transport case Faster acceptance checks with clear Go/No‑Go results The set enables straightforward Go/No‑Go inspection across a continuous diameter range, reducing decision time at the inspection bench. Conformity to DIN 2245 and the H7 tolerance class ensures that acceptance criteria are traceable to industry standards, which simplifies documentation and reduces downstream rework. By offering an organised series of gauges with fixed steps, the set speeds up routine checks and supports consistent pass/fail decisions during batch production without the need for complex measurement setups. Durable construction for stable repeatability Manufactured from hardened gauge steel, the gauges resist wear and preserve geometry under repeated use, maintaining measurement reliability over time. The set covers 3–30 mm in 1 mm increments, providing a tight gradation that avoids gaps in inspection coverage and reduces the need for interim measuring tools. This design delivers measurable savings in inspection throughput and lowers the risk of accepting out‑of‑tolerance parts, a clear efficiency argument for production environments where repeatability matters. Practical handling and organised storage for the workshop The gauges are supplied as a complete set with individual sizes arranged for quick selection, supporting a smooth workflow at the control station. The combined weight and pack format make the set robust for routine handling while remaining practical for bench use; bulk storage is simplified and gauges are protected during transport. Clear labelling of each gauge minimises handling time and helps maintain a tidy inspection area, contributing to faster cycle times and fewer process interruptions. For procurement or technical advice on the Metav IndustryLine limit plug gauge set, contact Metav Werkzeuge for detailed specifications or a tailored quotation — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M314.001.1 GTIN: 4054469164311 Brand: Metav IndustryLine Facts Measurement range: 3–30 mm Increment: 1 mm Pieces per set: 28 Weight: 9 kg Tariff code: 90173000 Special features Material: hardened gauge steel Standard: DIN 2245 Tolerance: H7 Included diameters: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30 FAQ What inspection method does the set support? The limit plug gauge set supports classic Go/No‑Go inspection of internal diameters, allowing immediate acceptance or rejection against the DIN 2245 H7 specification. Which diameter range and resolution are covered? The set covers 3–30 mm with 1 mm increments, provided as a complete 28‑piece series for continuous coverage across that range. What material are the gauges made from and why does it matter? Gauges are made from hardened gauge steel, which ensures long‑term resistance to wear and stable contact geometry for reproducible inspection results. Is the set suitable for production environments? Yes, the organised series and robust construction make the set suitable for workshop and production use where fast acceptance testing and repeatability are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3-32mm Limit Go Gauge Set H7, 17 Pieces DIN 2245 Hardened Gauge Steel, Wooden Case - Metav IndustryLine
Robust hardened gauge steel construction combined with the H7 tolerance range and a comprehensive 3–32 mm span provides consistent go/no‑go checks for workshop and inspection routines. The 17‑piece arrangement to DIN 2245 ensures systematic coverage of common diameters and reduces set‑up time. Order the limit gauge pin set directly via Metav Werkzeuge or consult the team for tailored procurement advice. Limit gauge pin set M314.001 — H7 tolerance, DIN 2245, 3–32 mm, 17‑piece (Metav IndustryLine) The limit gauge pin set M314.001 offers a compact, standards‑based solution for rapid acceptance testing and routine quality control across metalworking and assembly operations. H7 tolerance to DIN 2245 Hardened gauge steel construction Complete 3–32 mm range in 17 pieces Suitable for workshop and inspection use Faster acceptance decisions with standardised gauges The primary advantage of the limit gauge pin set lies in its ability to convert dimensional inspection into immediate, binary decisions: go or no‑go. Built to DIN 2245 and specified to H7, the pins allow fast verification of hole systems and mating components without time‑consuming micrometre setups. The calibrated step progression across the 3–32 mm span reduces interpolation and guesswork, so routine checks are completed faster and with repeatable outcomes. By standardising inspection steps, process throughput improves while documentation stays consistent. Durable construction for repeated workshop use Manufactured from hardened gauge steel, the set resists wear across frequent handling and abrasive shop environments. Each member of the 17‑piece assortment maintains dimensional integrity under cyclic use, which lowers the need for frequent replacement and supports a stable quality routine. The physical robustness contributes to measurement reliability over time, helping to keep rework and rejects at bay. For operations that perform high volumes of acceptance checks, the material choice and heat treatment translate directly into lower lifetime cost per measurement. Organised inventory and straightforward traceability The set is supplied as a cohesive unit that simplifies inventory control and traceability: entries such as M314.001 and the GTIN enable prompt recognition in procurement and stock systems. Conformity to DIN 2245 provides compatibility with existing inspection plans and fixtures, easing integration into quality workflows. Clear identification and a standardised size sequence also support quick tool selection during audits and shift changes, reducing downtime linked to locating the right gauge. Choose the Metav IndustryLine limit gauge pin set for dependable tolerance checks — contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for availability and delivery options Technical Data Article number: M314.001 GTIN: 4054469169217 Tariff code: 90173000 Weight: 3.4 kg Set pieces: 17 Facts Measuring range: 3–32 mm Standard: DIN 2245 Tolerance: H7 Special features Material: hardened gauge steel Set type: limit gauge pin set Sizes included: 3, 4, 5, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 25, 28, 30, 32 FAQ What is the intended use of this gauge set? The limit gauge pin set M314.001 is intended for go/no‑go checks and acceptance testing of holes and mating parts in workshop and inspection environments. Which standard and tolerance class apply to the pins? The set complies with DIN 2245 and is specified to H7 tolerance for standardised dimensional verification. What material are the pins made from? Pins are produced from hardened gauge steel to ensure wear resistance and long service life under repetitive use. How many pieces are included and which sizes are covered? The M314.001 set contains 17 pieces covering sizes from 3 mm up to 32 mm in commonly used diameter steps. Can the set be identified in procurement and stock systems? Yes; use the article number M314.001 and GTIN 4054469169217 for ordering and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3-4mm Ceramic Gauge Pin Set 0.01mm Steps, Stainless Zirconia, HV1250, Holder, Plastic Case - Metav IndustryLine
Take advantage of the combination of zirconia ceramic robustness, sub‑micron accuracy and workshop‑ready packaging for reliable bore checking and repeatable gauging; order the ceramic gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Ceramic Gauge Pin Set, 101-piece (3.00–4.00 mm, 0.01 mm steps) — Metav IndustryLine A Ceramic Gauge Pin Set designed for precise plug gauging and fine mechanical inspection across the 3.00–4.00 mm range with 0.01 mm increments Zirconia ceramic, antimagnetic and wear‑resistant High hardness HV 1250 for long service life Precision tolerance < ±0.0015 mm Supplied with holder and plastic case Repeatable high‑precision measurement where it matters The set is built from zirconia ceramic, a material that combines low wear, corrosion resistance and inherent antimagnetic properties; this makes it especially suitable for measurements where steel pins could introduce magnetic interference or wear quickly. With an indicated accuracy < ±0.0015 mm and a graduation of 0.01 mm, the pins deliver very tight tolerances that support confident go/no‑go assessments and dimensional verification in laboratory and production settings. The stated HV 1250 hardness explains the long service life and the low wear rate under normal gauging loads, reducing the frequency of replacement and maintaining consistent measurement results over time. Workshop practicality and handling benefits Supplied in a compact plastic case with an integrated measuring pin holder and presented in a workshop specification at 50 mm shank length, the set is optimised for everyday use on the shop floor. The case keeps the pins organised and protected during transport and storage, while the holder speeds up changeover between sizes, reducing cycle time for repetitive inspections. The compact design and non‑metallic composition make the tooling light to handle and simple to integrate into existing inspection benches or portable checking kits, helping to maintain throughput without compromising on measurement fidelity. Applications where non‑magnetic, stable gauging improves results This kit supports precise plug gauging, bore verification and match‑testing of micro components—fields such as precision engineering, horology, optical assembly and fine‑mechanics benefit from a non‑corroding, dimensionally stable gauge material. The sub‑micron class tolerance is particularly valuable when acceptance criteria demand minimal clearance or when comparing mating components over multiple production runs. Metav’s emphasis on accessible precision means this solution is offered with the practicality and supply reliability expected by workshops and production facilities across Europe. For workshop enquiries or to order this Metav IndustryLine ceramic gauge pin set directly from Metav Werkzeuge, contact our specialists in Emmerich for tailored advice and delivery options Technical Data Article number: M318.593 Description: Ceramic gauge pin set, 3.00–4.00 mm, 0.01 mm steps Range: 3.00–4.00 mm Increment: 0.01 mm Hardness: HV 1250 Accuracy: < ±0.0015 mm Length: 50 mm Pieces: 101 Facts Measurement range: 3.00–4.00 mm Step size: 0.01 mm Maximum stated tolerance: < ±0.0015 mm Hardness: HV 1250 Shank length: 50 mm Set size: 101 SKU: M318.593 Special features Material: zirconia ceramic Antimagnetic Wear‑resistant Workshop execution With measuring pin holder Supplied in plastic case Intended for precise plug gauging and fine mechanical inspection FAQ What measurement range does this gauge pin set cover? The ceramic gauge pin set covers the 3.00–4.00 mm range with 0.01 mm increments for fine‑step checking. Is the material suitable for use near magnetic fields? Yes. The pins are made from zirconia ceramic, which is antimagnetic and therefore suitable where magnetic interference must be avoided. How precise are the pins and what tolerance can be expected? The pins are specified with an accuracy of < ±0.0015 mm, making them suitable for demanding dimensional checks and close‑fit assessments. Does the set include storage and handling accessories? The kit is supplied in a plastic case and includes a measuring pin holder for rapid handling and secure storage. Which industries or applications benefit most from this kit? Precision engineering, horology, optical and micro‑mechanical assembly benefit from the non‑corroding, low‑wear ceramic pins and their tight tolerances; the Metav IndustryLine set (SKU M318.593) is geared towards these uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3-4mm Gauge Pin Set 21-Piece 70mm Steps 0.05mm Special Steel Plastic Case - Metav IndustryLine
Take advantage of a precisely graduated 0.05 mm step range, the compact 3.00–4.00 mm coverage and robust special‑steel construction to standardise routine bore inspections; order the set directly via Metav Werkzeuge or consult our technical advisers for application support. Gauge pin set M318.823 — 21-piece, 3.00–4.00 mm, 0.05 mm steps The gauge pin set for fast, repeatable verification of hole diameters in production and quality control, suitable for workshop and inspection use 21-piece set covering 3.00–4.00 mm in 0.05 mm steps Pins 70 mm length for deep bore verification Special steel for wear resistance and stability Fine 0.05 mm graduation for repeatable checks Consistent dimensional checks with clear graduations The 21-piece set provides continuous increments across a narrow diameter band, making it ideal where small tolerance steps are required. Each pin advances by 0.05 mm, a graduation that supports consistent go/no‑go style checks and stepwise narrowing of bore acceptance. For quality managers and shop‑floor inspectors this means fewer measurement cycles to locate out‑of‑tolerance features and faster decision making. The concise diameter coverage of 3.00–4.00 mm reduces handling complexity while preserving the diagnostic detail required for precision components. Robust pins for everyday shop use Constructed from special steel, the pins combine surface durability with dimensional stability during repeated seating and removal. The 70 mm length is beneficial when verifying deeper bores or through‑holes, offering access beyond what short pins permit without compromising rigidity. The set form factor keeps the assortment organised and accelerates part changeover. Users will notice reduced rework and more predictable inspection times thanks to the material choice and consistent pin geometry. Practical benefits for inspection workflows Adopting this set helps to streamline routine inspections: the fine 0.05 mm stepping supports close tolerance screening, while the compact diameter range allows quick narrowing of suspect features. The construction and finish minimise burr transfer and sticking, which keeps throughput steady. Traceability is supported by the clear marking and the product identifier M318.823, which simplifies calibration records and stock management for the quality department. Contact Metav Werkzeuge in Emmerich for application advice and dependable supply of Metav IndustryLine inspection tools Technical Data Article number: M318.823 GTIN: 4054469181950 Manufacturer: Metav IndustryLine Measuring range: 3.00–4.00 mm Step size: 0.05 mm Pin length: 70 mm Pieces per set: 21 Weight: 0.78 kg ECLASS: 21170231 Material: Special steel Set: yes Label: Prüfstift‑Satz, 21‑tlg. 3–4 mm, 70 mm, 0.05 mm step SKU: M318.823 FAQ What is the measurement increment of the pins? The pins are graduated in 0.05 mm increments, allowing fine resolution checks across the 3.00–4.00 mm range. Are the pins suitable for deep bore inspection? Yes, the 70 mm pin length is designed for deeper bores and through‑hole verification in typical workshop components. What material are the pins made from? The set is manufactured from special steel, chosen for its wear resistance and dimensional stability under repeated use. How many pieces are included and how does that help inspection speed? The set contains 21 pieces, enabling stepwise narrowing of tolerances and quicker identification of marginal bores without swapping disparate tools. How should the set be referenced in inventory and calibration records? Use the product identifier M318.823 and GTIN 4054469181950 for consistent stock control and traceable calibration records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com