Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
37 mm Gauge Ring, Hardened Ground Steel, Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Reliable measurement repeatability and standard‑compliant construction make this setting ring an essential calibration reference for inspection and workshop use. Benefit from hardened, lapped gauge steel and conformity with DIN 2250 and DIN 286 (JS 3) for reproducible fits and master measurements. Order the setting ring directly via Metav Werkzeuge or consult our specialists for fitting advice. Setting ring 37 mm — gauge ring for calibration, hardened and lapped (Metav IndustryLine) The Setting ring 37 mm is a compact precision gauge ring intended as a dimensional master for calibration tasks and fit verification in inspection and production environments. Hardened and lapped gauge steel Conforms to DIN 2250 and DIN 286 Tolerance grade JS 3 for accurate fits Compact 37 mm diameter reference Precision engineered for dependable master measurements The ring is manufactured from gauge steel, hardened and lapped, a combination that ensures high surface quality and dimensional stability. Compliance with DIN 2250 and DIN 286 guarantees defined tolerances and surface conditions; the JS 3 grade specifies the narrow tolerance band used for reference gauges, which directly reduces measurement uncertainty in go/no‑go checks and setting procedures. The design focus on repeatability supports consistent tool setting and fixture calibration over many cycles. Robust reference for everyday inspection and setting tasks A solid, wear‑resistant ring made from temper‑stabilised steel provides long service life under routine handling and repeated contact with setting instruments. As a metrological reference, the component minimises setup time on presetting devices and ensures reliable mating with shafts or mandrels during pass/fail checks. The combination of hardened substrate and a fine lapped finish reduces risk of fretting and surface damage, preserving the reference dimension across many measurement operations. Time‑saving certainty in production control Using a clearly specified reference ring shortens calibration workflows and lowers cumulative measurement drift: because the ring meets recognised standards and a fixed tolerance class, checks can be automated or standardised across shifts with predictable outcomes. The compact diameter makes the item easy to store and integrate into bench kits or gauge sets while still delivering the stability expected from master gauges. Traceable labelling and a consistent manufacturing routine further support process documentation and quality records. For application recommendations or to select the appropriate reference for a specific inspection procedure, contact Metav Werkzeuge — our Emmerich‑based specialists will advise on integration into existing quality systems and delivery options. Technical data Article number: M313.037 GTIN: 4054469120744 Brand: Metav IndustryLine Classification: eClass 21170104 Facts Diameter: 37 mm Tariff code: 90173000 Standard: DIN 2250; DIN 286; tolerance JS 3 Special features Material: gauge steel, hardened and lapped Form: Form C Intended use: master/reference gauge for calibration and fit verification FAQ What tolerance grade does the ring comply with? The ring is manufactured to tolerance grade JS 3, in accordance with the specifications in DIN 2250 and DIN 286, providing a tight tolerance suitable for reference applications. Can the ring be used as a master for setting chucks and mandrels? Yes. This gauge ring serves as a metrological reference for setting operations and fit checks, offering a stable, wear‑resistant mating surface for presetting and inspection tasks. What material and surface finish are specified? The component is made from gauge steel, which is hardened and lapped to produce a fine surface finish and maintain dimensional stability over repeated use. Is the product suitable for routine workshop use? Designed for regular inspection and calibration workflows, the compact 37 mm diameter and robust finish make it well suited to workshop benches and gauge kits where reproducible results are required. What is the product SKU for ordering and documentation? The item is listed under SKU M313.037 (Metav IndustryLine) for ordering and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
37 mm Go/No-Go Plug Gauge H7 Hardened Gauge Steel DIN 2245 - Metav IndustryLine
The supplied product data contain internal contradictions that prevent the creation of a reliable product description. Specifically, there are inconsistent entries for the item's mass and conflicting indicators of its condition, which make it impossible to state certified technical specifications or quality status with confidence. To avoid passing on potentially incorrect information to customers, a verified data set is required before a full product text can be generated. Please review and confirm the correct mass and the definitive quality flag for this item; once those key details are reconciled, a complete, standards-compliant product description aligned with DIN norms and Metav IndustryLine branding can be produced promptly. If assistance is needed to resolve the discrepancies, contact the data provider or Metav Werkzeuge for clarification.
38mm Limit Gauge DIN 2245 H7 Hardened Gauge Steel 0.64kg - Metav IndustryLine
Take the benefit of a hardened gauge steel design and DIN 2245 conformity to ensure reliable bore inspection to H7 tolerance; order via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge 38.0 mm H7 (DIN 2245) — Metav IndustryLine The Limit plug gauge 38.0 mm H7 is a hardened gauge intended for rapid acceptance checks of cylindrical bores to DIN 2245, providing a compact, standardised solution for workshop and production inspection. DIN 2245 conformity Hardened gauge steel construction Precisely ground 38.0 mm H7 diameter Fast, standardised verification for production control The plug enables efficient verification of bore conformity through a simple go/no-go acceptance approach, cutting inspection time while maintaining traceable results. Built to the DIN 2245 requirement and produced to the H7 fit, the gauge supports consistent precision across repeated checks. This makes it well suited for assembly lines and sample testing where reproducibility and adherence to specification are decisive for quality control. Robust material and finish for long service life Manufactured from hardened gauge steel, the plug offers wear resistance and dimensional stability under normal workshop use. The hardened construction reduces surface wear from repeated insertion, helping to preserve the calibrated diameter and extend service intervals. As a result, the gauge sustains reliable measurement performance, supporting fewer replacements and lower downtime in routine inspection tasks. Practical integration into inspection routines The compact design of the plug simplifies handling during spot checks and fixture audits. Where rapid go/no-go decisions are required, the plug provides an unambiguous assessment of bore acceptance to the H7 tolerance, enabling clear pass/fail outcomes. Backed by Metav’s commitment to accessible precision and a broad product range, this gauge is an economical choice for shops that need dependable, standards-based inspection tools. Contact Metav Werkzeuge for tailored inspection advice or to obtain the Metav IndustryLine limit plug gauge 38.0 mm H7 for immediate integration into production checks. Technical data Article number: M314.038 GTIN: 4054469121666 Eclass: 21170218 Manufacturer: Metav IndustryLine Core specifications Diameter: 38.0 mm Tolerance/fit: H7 Standard: DIN 2245 Customs tariff number: 90173000 Materials & features Material: hardened gauge steel Categories: Gauge pins; Gauges Intended use: Acceptance testing of cylindrical bores FAQ What tolerance and standard does this gauge check? The limit plug gauge checks bore conformity to the H7 tolerance and is manufactured to DIN 2245 standards for clear acceptance criteria. What is the nominal diameter of the gauge? The plug is specified at 38.0 mm nominal diameter and is available under article number M314.038. What material is the gauge made from and why does it matter? The gauge is made from hardened gauge steel, chosen for wear resistance and dimensional stability to ensure repeatable inspection results. Can this gauge be used for rapid production checks? Yes; the design is tailored for fast go/no-go assessments and supports efficient sample testing in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
38mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
Combine precise conformity to recognised standards with a hardened, lapped construction for dependable setting and repeatable results. Take advantage of the combination of dimensional stability, clear tolerances and workshop compatibility — order the setting ring directly via Metav Werkzeuge or ask our consultants if needed. Setting ring M313.038 — 38 mm, Form C, hardened gauge steel (Metav IndustryLine) A Setting ring M313.038 engineered as a compact, traceable gauge for accurate setting and comparative checks in workshop and inspection environments. Setting ring 38 mm, Form C Conforms to DIN 2250 and DIN 286 JS 3 Hardened, lapped gauge steel Reliable standards for fast, repeatable setups The ring is manufactured to meet DIN 2250 and DIN 286 with tolerance class JS 3, ensuring consistent interchangeability when used as a reference in production and inspection. This conformity reduces setup time and the need for repeated adjustments because the nominal diameter is produced within defined statistical limits. The combination of standardisation and a clear tolerance class delivers a measurable advantage in process control and makes the component suitable as a workshop master for go/no-go or comparative gauging. Wear resistance that keeps tolerances over time Constructed from gauge steel, the component is hardened and lapped, which improves surface stability and lowers running-in wear during repeated contact. The lapping process refines the contact surfaces to reduce local abrasion and micro‑deformation, so dimensional accuracy is maintained over many cycles. For users requiring a robust reference device, this material and finishing approach translates into fewer replacements, less downtime and more predictable measurement behaviour in daily operations. Compact profile designed for practical integration The Form C design offers a compact outer profile that eases handling and placement in fixtures or set-up aids, while the 38 mm nominal diameter fits common shaft and plug-gauge routines. As a setting device, the ring provides a straightforward means to transfer a known dimension into a machine or measurement chain, supporting quicker alignment and improved repeatability in assembly, turning or inspection tasks. Its geometry and finish make it a pragmatic choice for use as a workshop reference when accuracy and ease of use matter. Contact Metav Werkzeuge for a specification check and to discuss supply of the M313.038 setting ring — the Emmerich-based team will advise on suitability for specific gauge systems and delivery options Technical Data Article number: M313.038 GTIN: 4054469120751 eClass: 21170104 Facts Diameter: 38 mm Tariff code: 90173000 Special features Form C Hardened and lapped gauge steel DIN 2250, DIN 286; tolerance JS 3 Category: Gauges / Setting rings FAQ What tolerance class does the ring meet? The M313.038 setting ring conforms to DIN 2250 and DIN 286 with tolerance class JS 3. What material and finish are used? The setting ring is made from hardened, lapped gauge steel, giving high surface stability and wear resistance. How is Form C relevant to everyday use? Form C indicates a compact external profile that simplifies handling and positioning in fixtures and set-up aids, improving usability in workshop routines. Can the ring be used as a workshop reference for setting machines? Yes. The M313.038 is suitable as a reference setting ring for aligning spindles, checking shafts and transferring known diameters into production set-ups. What is the nominal diameter and typical application? Nominal diameter is 38 mm; typical applications include master checks, go/no-go routines and component set-up in turning and inspection operations. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Ceramic Gauge Ball (Si3N4) 0.003mm Accuracy, HV1400-1700 Hardness - Metav IndustryLine
Benefit from the combination of Si3N4 ceramic durability, a 3 mm nominal diameter and 0.003 mm accuracy for reliable reference measurements and reduced rework. Order the gauge ball directly via Metav Werkzeuge or ask our consultants for application-specific advice. Ceramic gauge ball M318.433 – Si3N4, 3 mm, 0.003 mm accuracy (Metav IndustryLine) The Ceramic gauge ball M318.433 is a compact precision reference sphere designed for gauging, calibration rigs and metrology fixtures in workshop and laboratory environments. Si3N4 ceramic, high wear resistance Nominal diameter 3 mm with tight tolerance Diameter deviation 0.00008 mm Hardness HV1400–1700 for long service life Durable ceramic for repeatable reference points Manufactured from Si3N4 ceramic, this reference sphere combines low wear with thermal stability to deliver consistent dimensional behaviour over extended use. The high hardness HV1400–1700 reduces surface damage during contact probing, which in turn preserves measuring integrity and lowers the frequency of replacements. As a compact reference element, it is suitable for tight fixtures where a small, stable contact geometry is required, contributing to reliable production throughput and fewer calibration interruptions. Measurable precision that improves process control With a specified accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, the sphere gives quantifiable assurance when used as a reference for comparative measurements or for setting up gauge blocks and alignment fixtures. The very low surface roughness (0.00001) supports consistent probe contact and reduces scatter in repeated measurements. These properties help to tighten process control, shorten setup times and reduce downstream inspection uncertainty in machining and assembly operations. Practical form factor and workshop integration The 3 mm diameter offers a compact contact point that integrates easily into measurement jigs, fixtures and CMM adapters without occupying excessive space. At a nominal weight of 0.08 kg, handling and placement are straightforward, while the material’s chemical inertness simplifies cleaning and long‑term storage. Where a stable, miniature sphere is required for reference or gauging tasks, this precision component serves as a durable and low‑maintenance option that supports steady metrological practice. For dependable, repeatable reference measurements, specify the Metav IndustryLine ceramic gauge ball M318.433 and contact Metav Werkzeuge in Emmerich for application advice and supply Technical data Article number: M318.433 GTIN: 4054469184333 Material: Ceramic (Si3N4) Nominal diameter: 3 mm Accuracy: 0.003 mm Core data Diameter tolerance: 0.00008 mm Surface roughness: 0.00001 Hardness: HV1400–1700 Weight: 0.08 kg Applications & features Application: Gauging and precision reference use Category: Gauges (Lehren) Use cases: Calibration, fixture alignment, CMM reference sphere Story trigger: lehr‑/gauge applications FAQ What applications is this ceramic sphere intended for? The Ceramic gauge ball M318.433 from Metav IndustryLine is intended as a precision reference sphere for gauging, calibration fixtures and as a probing reference on CMMs and metrology rigs. What does an accuracy of 0.003 mm mean in practice? An accuracy of 0.003 mm denotes the maximum deviation from the nominal diameter expected for the gauge ball; this level of precision enables repeatable reference measurements and reliable comparative checks. How durable is Si3N4 for probing and repeated contact? Si3N4 ceramic offers high wear resistance and chemical inertness; with a hardness of HV1400–1700, the sphere resists surface damage from repeated probe contact, extending service life and maintaining measurement stability. How should the sphere be handled and stored to preserve accuracy? Handle the sphere with clean gloves, avoid dropping, and store it in a protective case or padded holder; clean gently with a lint‑free cloth and suitable solvent if necessary to maintain the contact surface. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Gauge Pin Length 50mm ±0.001mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy, compact handling and workshop‑grade construction for reliable end‑measure checks. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification support. Gauge pin M323.300 — Test pin, 3.00 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) Gauge pin M323.300 is a single test pin engineered for precise end‑dimension verification in workshop inspection and small‑part quality control. Workshop version for robust daily use Diameter 3.00 mm with ±0.001 mm accuracy Delivered in protective plastic case Precision where tight tolerances matter The clamp‑free, single‑piece test pin delivers ±0.001 mm positional accuracy for objective end‑measure verification. With a nominal diameter of 3.00 mm, the pin targets applications where deviations of a few micrometres are consequential; the specified tolerance corresponds to roughly 1 micrometre, enabling repeatable checks that support process stability and reduce scrap. This level of precision suits fine mechanical inspection tasks where objective numerical comparison is required rather than subjective assessment. Robust workshop construction for repeatable handling Made from special steel, the component is configured as a workshop execution product to withstand frequent use on the shop floor. The 50 mm gauge length provides a stable reference while remaining compact enough for quick handling; the slender design and low mass favour swift placement during batch checks. Supplied individually and housed in a protective case, the pin is protected against contamination and transport damage, supporting consistent measurement routines and minimizing downtime between inspections. Micro‑range size tailored for fine components Classified for micro measurements, the small diameter and short working length make this pin ideal for inspection of miniature bores, pins and precision features in watchmaking, medical components and micro‑mechanics. The compact format preserves stiffness at the contact interface, helping to avoid bending or misalignment that would otherwise degrade measured results. In practical terms, the pin enables straightforward verification of critical end dimensions without requiring clumsy adaptors or complex fixtures. Traceability and workflow integration The single‑item supply and clear identification (GTIN available) support traceable inspection workflows and inventory control. The geometry and tolerance specification allow easy inclusion in existing quality control procedures as a go/no‑go reference or as part of a documented inspection step. As a Metav IndustryLine product, the pin forms part of a broader strategy to make precision tools accessible to industrial and craft workshops, combining dependable build quality with simple logistical integration. For high‑precision end‑measure verification choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for tailored advice — e‑mail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.300 GTIN: 4061905055287 Label: Prüfstift, einzeln, 3,00mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 3.00 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Measurement range: 3 mm Special features Material: special steel Workshop execution Supplied individually Protective plastic case for transport and storage eClass: 21170231 FAQ What accuracy can be expected from the gauge pin M323.300? The gauge pin M323.300 is specified to ±0.001 mm, providing micrometre‑level repeatability suitable for fine inspection tasks. Is the pin supplied ready to use and protected for transport? Yes, the test pin is supplied individually and comes in a protective plastic case to prevent contamination and transport damage. Which materials is the pin suitable for checking? The pin itself is a measuring artefact for dimensional verification and is used to check component bores, pins and end features regardless of the workpiece material; suitability for specific machining or material compatibility depends on the inspection setup rather than the pin. Can the pin be integrated into an existing inspection routine? The compact geometry and standard identification enable simple integration into documented quality steps or fixture‑based checks as a reference for end‑dimension control. How is traceability handled for this item? The article is identifiable by SKU M323.300 and GTIN 4061905055287, supporting inventory and traceability requirements in inspection processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–12 mm Welding Gauge Set 12‑Piece For Weld Size Inspection, 12 Pieces - Metav IndustryLine
Take advantage of a compact set that enables fast verification of weld sizes across a 3–12 mm range, combining clear gradation and workshop‑ready simplicity for reliable quality checks; order the set directly via Metav Werkzeuge or contact their consultants for advice. Weld seam gauges set M318.032 — 3–12 mm range, workshop gauge set (Metav IndustryLine) Weld seam gauges M318.032 provide quick verification of weld dimensions for right‑angled joints, ideal for on‑bench quality checks in metalworking and fabrication Range 3–12 mm in fine steps Twelve gauges for weld measurements Designed for right‑angled welds Speed up inspection with a practical gauge set A concise set of gauges reduces measurement time during routine weld inspections. The included sizes cover the common leg and throat dimensions encountered in fabrication, enabling immediate pass/fail checks without transferring parts to a measuring bench. This translates into fewer interruptions on the shop floor and faster control loops for welding processes. The compact format supports efficient tool organisation and quick retrieval, which helps to maintain steady throughput. Consistent results for weld quality assurance Each gauge in the set is intended for a specific nominal size, allowing technicians to compare actual weld profiles against expected dimensions instantly. This direct comparison method avoids interpretation errors that can arise from sketching or approximate visual checks. As a result, the set supports consistent quality decisions and reduces the probability of rework, contributing to predictable production output and lower non‑conformance rates. Practical application and handling explained The gauges are used by placing the appropriate blade against a right‑angled weld to verify leg or throat size; the correct fit indicates conformity. This tactile method is particularly useful for spot checks and first‑article inspections where rapid confirmation is required. The simple, mechanical approach requires no power or calibration routines to perform everyday checks, making the set a robust companion for welders and inspectors in workshops and maintenance teams. Built for workshop use and process integration Designed as a straightforward inspection tool, the set integrates easily into existing quality workflows. The small, dedicated gauges enable teams to standardise measurement points for recurring assemblies, which simplifies documentation and traceability. When combined with Metav’s broader range of metrology products, the set can be part of a leaner quality strategy that balances practicality with traceable results. For workshop procurement and technical advice, contact Metav Werkzeuge to source the Metav IndustryLine weld seam gauges M318.032 and receive assistance on integration into existing inspection routines Technical data Article number: M318.032 GTIN: 4054469127781 Customs tariff: 90173000 Facts Pieces per set: 12 Size range: 3 / 3.5 / 4 / 4.5 / 5 / 5.5 / 6 / 6.5 / 7 / 8 / 10 / 12 mm Category: Gauges (Lehren) Special features Purpose: Measuring weld seams at right‑angled welded corners Use case: Workshop inspection, fabrication quality control Brand: Metav IndustryLine FAQ What does the set include? The set contains twelve individual weld seam gauges covering the 3–12 mm sizes supplied as Metav IndustryLine model M318.032 for direct dimensional checks. How is the gauge set used in practice? Select the blade matching the nominal weld size and place it against the right‑angled joint; correct seating indicates conformity, making this a fast method for comparative assessment. Is this set suitable for production spot checks? Yes, the M318.032 set is intended for routine workshop and shop‑floor spot checks where immediate, pass/fail verification of weld size is required. Does the set replace calibrated measurement equipment? The gauges serve for rapid verification and go/no‑go checks; they complement rather than replace calibrated metrology instruments when traceable measurement records are required. Can the gauges be integrated into a quality control workflow? The compact nature of the set and its clear size gradation make it simple to incorporate into inspection routines and standard operating procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–15mm Conical Bore Gauge 1:10 Taper, 0.1mm Graduation, Chrome‑Plated Steel Cone Aluminium Handle - Metav IndustryLine
Take advantage of a conical taper 1:10 and a 3–15 mm measurement range for fast, self-centring bore checks; the 0.1 mm graduation supports clear comparative decisions on the shop floor. Robust, matt‑chrome cone and an anodised aluminium handle reduce handling fatigue and extend service life. Order the Metav IndustryLine M318.046 directly via Metav Werkzeuge or consult our specialists for application advice. M318.046 — Tapered bore gauge (3–15 mm), 0.1 mm graduation The M318.046 is a compact conical bore gauge designed for precise checks of small cylindrical bores in workshops and quality control stations. Conical taper 1:10 for accurate centring Measurement range 3–15 mm for small bores Graduated at 0.1 mm for clear readings Matt‑chrome cone and anodised aluminium handle Reliable centring and quick pass/fail checks The conical geometry with a 1:10 taper produces a self‑centring action that simplifies alignment inside small bores. Combined with the 3–15 mm range and a 0.1 mm graduation, this configuration enables rapid comparative checks and straightforward go/no‑go assessments during assembly or incoming inspection. The instrument functions as a compact, tactile gauge: when the cone seats, the operator receives immediate positional feedback, reducing the need for repeated probe adjustments and shortening inspection cycles. Compact format for fine mechanical applications Classified in the Mikro group, the gauge covers the small‑bore segment where stiffness and handling are decisive. With a cone length of 135 mm and an overall length of 190 mm, the tool offers a slim envelope and a low mass (approx. 0.12 kg), which improves manoeuvrability in confined assemblies and during delicate measuring tasks. The lightweight anodised aluminium handle ensures comfortable one‑hand operation while the matt‑chrome plated steel cone resists wear and provides consistent contact behaviour over many cycles. Built for reproducibility and shop endurance Materials and form factor focus on repeatable results and a long service life. The matt‑chrome cone delivers a hard, wear‑resistant contact surface and stable friction characteristics, while the anodised aluminium handle reduces corrosion risk and improves grip. Supplied under the Metav IndustryLine umbrella, the instrument benefits from Metav’s quality filtering and European distribution, ensuring dependable availability for production lines and inspection benches. The compact tapered design therefore balances precision, durability and everyday usability for small‑bore measurement tasks. For detailed specification or to secure supply from Metav Werkzeuge’s Emmerich stock, contact Metav Werkzeuge about the Metav IndustryLine M318.046 and request tailored application advice. Technical data Article number: M318.046 GTIN: 4061905047794 eCl@ss: 21170208 Customs tariff number: 90173000 Facts Measurement range: 3–15 mm Graduation: 0.1 mm Cone length: 135 mm Overall length: 190 mm Weight: 0.12 kg Special features Conical taper 1:10 Cone material: steel, matt‑chrome plated Handle material: aluminium, anodised Compact Mikro class gauge for small bores Intended for cylindrical bore verification FAQ What measurement range does the M318.046 cover? The M318.046 covers a range of 3–15 mm with a 0.1 mm graduation for clear comparative readings. How does the conical taper improve measurement? The 1:10 conical taper on the M318.046 provides self‑centring and consistent seating, which aids rapid alignment and repeatable bore checks. What materials are used in the gauge construction? The M318.046 uses a matt‑chrome plated steel cone and an anodised aluminium handle to combine wear resistance with low weight. Is this gauge suitable for fine mechanical or watchmaking work? Yes; with a maximum range of 15 mm the M318.046 falls into the Mikro category and is tailored to compact, high‑precision tasks found in fine mechanical and micro‑assembly applications. How portable and easy to handle is the gauge? At approximately 0.12 kg and 190 mm overall length, the M318.046 is lightweight and manoeuvrable for one‑hand operation in confined spaces. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–4 mm Gauge Pin Set 101 Pieces 70 mm Length 0.01 mm Graduation Plastic Case - Metav IndustryLine
Combining 0.01 mm graduation, a compact 3.00–4.00 mm diameter range and a complete 101-piece composition, this gauge pin set delivers fast, repeatable diameter checks and helps to reduce rework on the production line. Order the set directly via Metav Werkzeuge or contact our consultants for specification support. Gauge Pin Set M318.853 — 3.00–4.00 mm, 0.01 mm graduation (Metav IndustryLine) The Gauge Pin Set M318.853 is a precision pin gauge kit for diameter inspection and go/no‑go verification in toolrooms and quality control. *Precision increments of 0.01 mm *Diameter range 3.00–4.00 mm *70 mm gauge pin length *Made from special steel for durability High‑precision increments for reliable pass/fail decisions Pin gauges are the simplest way to convert a dimensional requirement into a quick physical test. With a 0.01 mm graduation across the collection, this kit supports very fine selection steps so staff can perform repeatable checks without complex measuring routines. The compact graduation reduces decision time at inspection stations, leading to a steady throughput and fewer measurement ambiguities. The arrangement of incremental sizes also minimises tool change and keeps routine measurements consistent. Comprehensive set that speeds up inspection workflows A tightly graded range between 3.00–4.00 mm with close increments enables immediate matching to drawing tolerances and rapid sampling across small‑diameter lots. The set’s 101 pieces provide both nominal and intermediate sizes for contiguous coverage, which helps to cut setup time during first‑article inspections and in‑process checks. By simplifying diameter verification into a predictable set of go/no‑go or fit checks, shop floors gain efficiency and reduce scrap generated by uncertain measurements. Robust construction and practical handling for repeated use Manufactured from special steel, the pins combine wear resistance with stable dimensional behaviour under normal workshop conditions. Each pin’s 70 mm length is suited to through‑hole and blind‑bore checks where a reliable contact length improves alignment and reading confidence. The solid construction supports frequent handling and delivers consistent tactile feedback when used in assembly inspection or gauge comparisons. For production environments that prioritise repeatability, the set balances durability with ease of use. For tailored advice on using the Gauge Pin Set or to request a customised configuration, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M318.853 GTIN: 4054469182049 Brand: Metav IndustryLine Core measurements Measuring range: 3.00–4.00 mm Graduation: 0.01 mm Length: 70 mm Pieces per set: 101 Weight: 2.15 kg Materials and features Material: special steel Set type: pin gauges Application: diameter inspection and go/no‑go verification FAQ What diameters are covered by the set? The set covers diameters from 3.00 mm to 4.00 mm in 0.01 mm steps, enabling fine gradation across the range. How many pins are included in the Gauge Pin Set M318.853? The Gauge Pin Set M318.853 contains 101 pieces, offering comprehensive coverage for small‑diameter inspection work. What material are the pins made from and why is that important? Pins are made from special steel, chosen for wear resistance and dimensional stability, which supports repeated use and consistent measurement feedback. Is the pin length suitable for through‑hole checks? Yes, the 70 mm pin length provides sufficient engagement for many through‑hole and bore verifications, improving alignment and contact reliability. Can this set be used for go/no‑go testing in a production environment? The graded diameters and fine 0.01 mm graduation make the set well suited for go/no‑go and fit testing during in‑process quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–4 mm Gauge Pin Set With Holder 0.01 mm Graduation, Supplied In Case - Metav IndustryLine
Benefit from industrial-grade accuracy and a robust special‑steel design that streamlines small‑bore inspection and reduces rework. The compact set with a dedicated pin holder and 0.01 mm graduations supports faster, repeatable checks; order the set directly via Metav Werkzeuge or consult our specialists for tailored advice. Gauge pin set M318.573 — 101-piece, 3.01–4.00 mm, 0.01 mm increments (Metav IndustryLine) The gauge pin set M318.573 is a compact inspection kit designed for precise verification of small bores and plug‑gauge tests in workshop and production environments Complete set with pin holder 0.01 mm graduated precision Range 3.01–4.00 mm Special steel for long life Precise inspection made consistent and efficient The gauge pin assortment delivers measurable gains in repeatability for routine bore checks. With 0.01 mm increments and a declared accuracy of 0.004 mm, the pins enable close conformity checks and fine adjustment of tooling and fixtures. The stepped selection reduces downtime spent searching for a matching size and allows quick narrowing to the correct diameter for go/no‑go decisions. Robust construction in special steel supports frequent handling and maintains dimensional stability during repeated use, which raises throughput without compromising measurement confidence. Practical benefits for workshop and quality control Designed as a purpose‑built kit, the assortment includes a pin holder that keeps sizes organised and accelerates the selection process during inspections and setup operations. The compact range centred on 3.01–4.00 mm suits small components, gauges and precision parts typical in horology, connector manufacture and fine mechanical assemblies. Using graded pins avoids iterative adjustments on machines and jigs, cutting setup time and lowering scrap rates—an immediate efficiency advantage for production and maintenance teams. Integration into verification routines and tooling checks The set performs well as a reference for incoming inspection, process control and fixture verification. Its finely graded steps make it suitable for establishing master gauges or checking bore wear in series production. The material choice and manufacturing tolerances ensure each pin remains a reliable reference over time; when combined with a consistent handling procedure, the assortment supports documented quality checks and repeatable measurement routines that feed directly into traceable inspection records. For a tailored quotation or technical clarification on the Metav IndustryLine gauge pin set, contact Metav Werkzeuge for expert guidance and swift supply from Emmerich Technical data Article number: M318.573 GTIN: 4054469168272 Manufacturer: Metav IndustryLine Facts Measurement range: 3.01–4.00 mm Increment (graduation): 0.01 mm Declared accuracy: 0.004 mm Weight: 1.66 kg Special features Material: special steel Set composition: 101 pieces Holder: included for organised storage Tariff number: 90173000 Categories: Messstifte; Lehren FAQ What tolerance can be expected from this gauge pin set? The declared tolerance is 0.004 mm; the gauge pin set M318.573 is manufactured and finished to deliver close dimensional conformity suitable for precision checks in small‑bore applications. Is the pin holder included and how does it help workflow? Yes, a pin holder is included; it organises the pins by size and speeds selection during inspection and setup tasks, reducing handling time and error risk with the gauge pin set. Which materials and applications suit these pins? Made from special steel, the pins are intended for general precision inspection of small bores and plugs, commonly used in fine mechanical assemblies, connectors and tooling checks. Can the set be used as a master reference in fixture adjustment? The graded increments and tight accuracy make the assortment suitable as a reference for fixture verification and repeatable setup procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4 mm Ceramic Gauge Ball (Si3N4) Accuracy 0.003 mm, HV1400-1700 Hardness - Metav IndustryLine
A compact reference sphere that combines Si3N4 ceramic hardness, sub‑micrometre surface finish and tight diameter tolerance to deliver repeatable gauging results; ideal where consistent measurement and long service life matter. Benefit from high wear resistance and stable geometry to reduce rework and inspection time. Order the ceramic gauge ball directly via Metav Werkzeuge or ask our consultants if needed. Ceramic gauge ball (Si3N4), 4 mm — 0.003 mm accuracy | Metav IndustryLine The ceramic gauge ball (Si3N4), 4 mm is a precision reference sphere for gauging and inspection tasks, designed for use in gauge sets, comparators and quality‑control fixtures Si3N4 ceramic, 4 mm diameter Dimensional accuracy 0.003 mm Diameter tolerance ±0.00008 mm Surface roughness 0.00001 Consistent results for tight tolerances Manufactured from Si3N4 ceramic, this small reference sphere delivers a dimensional accuracy of 0.003 mm, making it suitable for high‑precision comparative measurements and repeatable inspection routines. The tight diameter tolerance of 0.00008 mm and extremely low surface roughness minimise measurement scatter when used as a master sphere or reference in comparator setups. For production environments that demand traceable repeatability, the combination of low form deviation and fine finish reduces the risk of false rejects and shortens calibration cycles, thereby improving throughput and lowering overall inspection costs. Durability that sustains accuracy over time The material hardness of HV1400–1700 gives the sphere outstanding wear resistance in contact applications, maintaining spherical geometry under repeated loading. With a mass of 0.08 kg and compact 4 mm size, handling is straightforward while the robust ceramic resists typical wear mechanisms encountered in gauge use. These material properties translate into longer intervals between replacements and fewer process interruptions. In assembly and inspection workflows where component interchangeability is critical, a stable reference sphere preserves the integrity of measurement chains and supports long‑term quality assurance. Integrates smoothly into metrology routines Engineered for gauge and inspection applications, the sphere fits directly into precision gauge sets, plug gauges and shank adaptors used on comparators and manual inspection benches. Use as a reference master for surface‑contact probes or as a check artefact for small‑diameter features ensures compatibility with standard metrology procedures. The compact form also makes it suitable for confined fixturing in component checks. If further advice on integration into a specific inspection setup is required, Metav’s distribution and technical team can provide guidance on fixture options and handling to preserve the sphere’s form and finish. Choose the Metav IndustryLine ceramic gauge ball for dependable reference measurements and contact Metav Werkzeuge in Emmerich for specialist advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M318.434 GTIN: 4054469184340 Manufacturer: Metav IndustryLine Facts Diameter: 4 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Surface roughness: 0.00001 Hardness: HV1400–1700 Weight: 0.08 kg Special features Material: Ceramic (Si3N4) Extremely fine surface finish Tight dimensional stability Intended for gauges and inspection (lehren) FAQ What diameter and accuracy does the sphere offer? The ceramic gauge ball has a diameter of 4 mm and a stated accuracy of 0.003 mm for high‑precision reference use. Which material is used and how hard is it? The sphere is made from Si3N4 ceramic with hardness in the range HV1400–1700, providing high wear resistance for contact measurements. Is the diameter tolerance and surface quality suitable for master gauges? Yes; the diameter tolerance of 0.00008 mm and a surface roughness value of 0.00001 make it suitable as a master or reference sphere in small‑scale gauging. Can this sphere be used on comparators and in gauge sets? The 4 mm ceramic sphere is intended for gauge and inspection applications and is compatible with comparator fixtures and small gauge adaptors. Is a calibration certificate included with the product? No calibration certificate is indicated in the product data for this item Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4 mm Ceramic Setting Ring 0.001 mm Accuracy, Wear-Resistant Antimagnetic Zirconia - Metav IndustryLine
Take advantage of the combination of zirconia ceramic durability, ±0.001 mm accuracy and high hardness (HV 1250) to secure repeatable reference dimensions in workshop environments; order directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic setting ring 4 mm — Zirconia, ±0.001 mm (Metav IndustryLine) The Ceramic setting ring 4 mm 0.001 mm (30x8) is a workshop-grade zirconia ring designed for precise setting, calibration and spacing tasks in metrology and assembly applications. Zirconia ceramic, corrosion-resistant Antimagnetic and low wear Precision ±0.001 mm accuracy Precision where it matters: consistent reference for setups Built from zirconia ceramic, this setting ring offers a very high hardness (HV 1250) and exceptional dimensional stability. The combination of material hardness and a ±0.001 mm tolerance ensures the ring functions as a reliable reference surface in repetitive setup operations, reducing the need for frequent recalibration and lowering scrap rates. The non-corroding, wear-resistant surface maintains critical dimensions across many cycles, which supports predictable machine setup times and consistent production quality. Designed for demanding workshop use: robust and non-magnetic The workshop specification means the gauge is engineered for regular handling and integration into production workflows. Being antimagnetic avoids interference near magnetic components or instruments, while the material’s inherent wear resistance preserves the bearing surface against scoring and abrasion. These properties translate into less downtime for replacement and a longer service life compared with softer reference rings, improving overall equipment effectiveness in the measurement chain. Practical benefits: easier processes, measurable savings As a hardened ceramic reference, the ring minimises measurement drift and helps stabilise process control. Using a stable gauge with micron-level accuracy supports tighter tolerances on assemblies and reduces rework. For quality teams, the predictable behaviour of a ceramic setting ring simplifies inspection routines and traceability. The compact design (30 x 8 mm) suits confined fixturing and allows integration into jigs, masters or modular test plates where a reliable datum is required. Choose Metav IndustryLine when absolute dimensional control matters — contact Metav Werkzeuge for delivery and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M313.K04 Manufacturer: Metav IndustryLine Nominal size: 4 mm Accuracy: ±0.001 mm Hardness: HV 1250 Dimension (mm): 30 x 8 Material: zirconia ceramic Antimagnetic Wear-resistant Workshop version FAQ What tolerance can be expected from the ceramic setting ring? The ceramic setting ring delivers an accuracy of ±0.001 mm, making it suitable for fine calibration and precision setup tasks. Is the material suitable for use near magnetic equipment? Yes, the ring is antimagnetic, so it can be used close to magnetic instruments and components without affecting readings. How does zirconia ceramic benefit long-term use compared with steel? Zirconia ceramic offers high hardness (HV 1250) and superior wear resistance, which preserves dimensions and reduces the frequency of replacement compared with softer metals. Can the ring be used as a datum in assembly fixtures? The compact dimensions (30 x 8 mm) and stable surface make this ring appropriate as a reference datum in fixtures and modular test plates. Which product code should be quoted when ordering or enquiring? Please quote SKU M313.K04 and the Metav IndustryLine designation for precise identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4 mm Gauge Ball Pair, Hardened Chrome Steel, 0.003 mm Accuracy, Tolerance 0.00008 mm - Metav IndustryLine
Robust, hardened chrome‑steel gauge balls with 0.003 mm positional accuracy and a submicron surface finish deliver reliable reference points for small‑part inspection and probe calibration; their HRC >62 hardness ensures excellent wear resistance under repeated contact. Order the gauge ball pair directly via Metav Werkzeuge or ask our consultants if needed. Gauge Ball Pair M318.414 – 4 mm, hardened chrome steel, 0.003 mm accuracy The gauge ball pair M318.414 is a precision reference for dimensional inspection, probing and calibration tasks in metrology and quality‑control workshops. Hardened chrome‑steel, HRC >62 Diameter 4 mm, precision gauge spheres Accuracy 0.003 mm for reference measurements Supplied as a two‑piece set Precision that keeps measurement reliable Manufactured as a compact reference, these gauge spheres combine a 4 mm diameter with a declared accuracy of 0.003 mm, making them suitable as control artefacts for small‑scale inspections and tactile probe checks. The tight diameter tolerance of 0.00008 mm and an ultra‑smooth surface roughness of 0.00001 mm reduce measurement noise and support reproducible contact conditions; this is particularly valuable when validating probe repeatability on coordinate measuring machines or checking stylus calibration. The compact geometry also minimises contact area distortion, translating material properties into predictable measurement behaviour. Built for wear resistance and consistent repeatability The choice of hardened chrome steel and a hardness rating above HRC 62 prioritises long‑term durability where repeated probing or mechanical contact occurs. High hardness reduces plastic deformation and preserves spherical geometry, which in turn maintains dimensional integrity across many cycles. For workshops that rely on frequent comparative checks, this wear resistance lowers the need for frequent replacements and helps preserve the calibration state of inspection equipment. The result is stable metrology performance and fewer interruptions to production‑control routines. Practical integration into inspection workflows Supplied as a two‑piece set, the pair serves as a convenient reference for comparative measurements, fixture set‑up and spot checks of probe systems or micro‑alignment tools. The small mass and 4 mm diameter make the pair easy to position in jigs, on kinematic mounts or under probe tips without introducing significant inertia. Where space is limited or workpieces are miniature, these spheres function as reliable datum points and aid in establishing traceable measurement chains. The compact reference pair supports efficient quality checks and helps technicians reach decisions faster with objective, repeatable data. Discuss the M318.414 gauge ball pair with Metav Werkzeuge to align this hardened 4 mm reference solution with existing probe and inspection routines Technical data Article number: M318.414 GTIN: 4054469184029 Material: Hardened chrome steel Diameter: 4 mm Accuracy: 0.003 mm Hardness: >HRC 62 Surface roughness: 0.00001 mm Tolerance (diameter): 0.00008 mm Pieces per set: 2 Weight: 0.05 kg Facts Diameter: 4 mm Accuracy: 0.003 mm Tolerance: 0.00008 mm Surface roughness: 0.00001 mm Hardness: >HRC 62 Weight: 0.05 kg Pieces per set: 2 Special features Hardened chrome steel construction Supplied as a pair for comparative use Designed as a precision reference for inspection and probing GTIN and SKU for traceability and ordering FAQ What are the primary uses for these gauge balls? The gauge ball pair M318.414 from Metav IndustryLine is intended as a precision reference for tactile probe checks, fixture set‑up and small‑part inspection where compact, repeatable datum points are required. Can these spheres be used on coordinate measuring machines (CMMs)? Yes; the accuracy of 0.003 mm, combined with the controlled surface finish and tight diameter tolerance, makes the pair suitable as short‑range reference artefacts for CMM probe verification and comparative probe tests. How does the material choice affect long‑term use? The hardened chrome‑steel composition and HRC >62 rating give high wear resistance, preserving spherical form under repeated contacts and helping to maintain consistent measurement behaviour over time. Are the balls supplied individually or as a set? The product is supplied as a two‑piece set, which simplifies comparative checks and fixture alignment without the need to source matching spheres separately. What cleaning or handling precautions are recommended? Handle the spheres with clean, lint‑free gloves or tweezers to prevent contamination; clean with a soft, lint‑free cloth and avoid aggressive chemicals that could damage the surface finish. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4 mm Gauge Ring Hardened Gauge Steel DIN 2250, JS3 - Metav IndustryLine
Product data inconsistency: the product label specifies DIN 2250, whereas the norm field lists DIN 286 and tolerance class JS3; this discrepancy may lead to confusion or errors in product identification and usage. It is essential to ensure that all specifications align accurately to maintain consistency and reliability. Please check and correct the specification to avoid potential misunderstandings or issues during application. Accurate data is crucial for compliance with industry standards and for ensuring the product meets the required performance criteria. Kindly review the details thoroughly and update the information to reflect the correct and consistent specifications.
4 mm Limit Gauge Go/No-Go Wear Allowance, DIN 7162 - Filetta
The hardened construction and conformity to DIN 7162 ensure reproducible acceptance checks, while the clearly indicated wear allowance on the go side supports long-term reliability. Combine robust material choice with standardised dimensions for consistent go/no‑go inspection; order the limit plug gauge directly via Metav Werkzeuge or consult its specialists for application advice. Filetta limit plug gauge — hardened steel, DIN 7162 A Filetta limit plug gauge designed for rapid go/no‑go checks of internal diameters, providing workshop-grade repeatability and a marked wear allowance for ongoing inspection integrity. Hardened steel construction DIN 7162 compliance Precision ground measuring pin Wear allowance on go side Dependable acceptance testing with hardened steel and standard conformity The gauge is manufactured from hardened steel, a material choice that resists surface deformation and maintains form under frequent use, which supports reproducible pass/fail decisions in production control. Conformity with DIN 7162 gives a clear normative basis for dimensioning and tolerances, reducing interpretation variations during inspection. The nominal size of 4 mm makes this item suitable for small bores and fine mechanical assemblies; the compact form factor simplifies handling while retaining the stiffness required for repeatable verification. How the wear allowance improves long‑term measurement reliability A distinctive characteristic is the wear allowance on the go side, which compensates for gradual material loss on the acceptance face and prolongs the interval between regrinds or replacements. The measuring pin is precision ground to present a stable reference surface for routine checks, so bench operators can rely on quick go/no‑go decisions without extensive setup. This targeted design reduces scrap risk and supports consistent quality control processes in small‑part production or inspection stations. Practical use and integration into workshop routines Constructed for straightforward bench use, the plug gauge fits into common inspection workflows and is compatible with existing go/no‑go procedures. The compact gauge is easy to store and retrieve, and the robust finish minimises maintenance needs. For quality systems, the clear marking of the wear allowance aids traceability in service records and in planning maintenance cycles, helping to maintain throughput without unexpected measurement drift. Choose Filetta's hardened steel limit plug gauge for reliable go/no‑go control and contact Metav Werkzeuge in Emmerich for order placement or technical consultation by phone or e‑mail Technical data Article number: MS911.164 Type: limit plug gauge Size: 4 mm Material: hardened steel Standard: DIN 7162 Facts SKU: MS911.164 Manufacturer: Filetta Special features Wear allowance on go side Precision ground measuring pin Intended for internal diameter acceptance testing FAQ What is the primary application of this limit plug gauge? The Filetta limit plug gauge is intended for quick go/no‑go verification of internal diameters, providing a pass/fail reference for small bores and fine mechanical parts. How does the wear allowance affect service life? The marked wear allowance on the go side extends the usable life of the gauge by compensating for gradual wear, helping to delay regrinding or replacement while maintaining acceptance criteria. Is the gauge suitable for laboratory calibration or only shop use? Manufactured from hardened steel and finished by precision grinding, the gauge is appropriate for workshop inspection and routine quality control; calibration scope depends on the laboratory procedure chosen. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4 mm Limit Gauge Pin Wear Allowance, Hardened Steel DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance for consistent pass/fail decisions and extended service life. Order the limit plug gauge directly via Metav Werkzeuge or contact our consultants for specification advice. Limit plug gauge – Filetta, hardened steel, DIN 7162 The Limit plug gauge is a precision go/no-go inspection pin designed for fast dimensional checks of bores and fittings in production and quality control. Hardened steel construction Manufactured to DIN 7162 Wear allowance on the good side Reliable pass/fail checking for fast quality control A compact limit plug gauge provides a straightforward binary decision in inspection routines, turning measurement into an immediate pass or fail. The combination of DIN 7162 conformity and a hardened shaft ensures that the gauge meets recognised geometric and tolerance requirements, which reduces interpretation time in quality control and accelerates throughput on the shop floor. This approach lowers downtime created by uncertain measurements and supports reproducible, traceable inspection results. Built for longevity and repeatable results Constructed from hardened steel, the pin resists abrasion and maintains a stable measuring diameter over many cycles, so calibration intervals can be extended without compromising confidence. The included wear allowance on the good side compensates for normal surface degradation, preserving the functional limit for go checks and reducing the need for immediate replacement. For maintenance planning this translates into predictable lifecycle costs and less frequent tool changeovers. Easy integration into workshop inspection processes Compliance with DIN 7162 means the gauge integrates cleanly into existing inspection plans and can be referenced in control documentation and reports. The simple geometry and compact design facilitate handheld use or fixture mounting, enabling quick comparison checks during in-process inspection or final quality control. The instrument functions as an efficient screening tool before more detailed metrology is applied, saving time while keeping measurement risk low. Suited applications and practical advantages Ideal for routine bore verification and acceptance testing, the gauge is suited to mechanical engineering, component assembly and finishing operations where fast, reproducible decisions are required. The small footprint of the pin makes it convenient in tight work stations and on assembly lines, while the robust material and standardised manufacture support long-term reliability. Where quick verification is needed, the plug gauge acts as a dependable first check. For DIN‑compliant limit gauging and practical advice from our Emmerich quality filter, contact Metav Werkzeuge to order Filetta limit plug gauges or to discuss application-specific recommendations: info@metav-werkzeuge.com / +49 2822 7131930. Technical data Article number: MS911.206 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Size: 4 mm Special features Wear allowance on the good side Category: Gauge pins / plug gauge Application: Pass/fail inspection of bores FAQ What is the primary purpose of this limit plug gauge? The limit plug gauge is intended for quick pass/fail verification of bore diameters and mating features during production and final inspection. Which material is used for the gauge? The Filetta limit plug gauge is made from hardened steel to ensure wear resistance and dimensional stability. Does the gauge comply with any standards? Yes, the gauge is manufactured in accordance with DIN 7162, ensuring standardised geometry and tolerance handling. What size does this article cover? This item is specified with a size of 4 mm and is listed under article number MS911.206. How does the wear allowance affect inspection? The built-in wear allowance on the good side maintains the effective go condition as the surface experiences normal abrasion, thus extending service life while preserving reliable go/no-go decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4 mm Limit Go/No-Go Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of the combination of DIN 2245 tolerance conformity, hardened gauge steel construction and compact 4.00 mm diameter for reliable pass/fail checks in production. Order the gauge directly via Metav Werkzeuge or ask the consultants for application advice. Limit plug gauge M314.004 — 4.00 mm H7 inspection gauge (Metav IndustryLine) A limit plug gauge M314.004 designed for fast go/no-go verification of 4.00 mm H7 bores in production control and incoming inspection. Limit plug gauge 4.00 mm H7 (DIN 2245) Hardened gauge steel for high wear resistance Fast go/no-go verification in production Keep tolerances under control with standardised checks The combination of DIN 2245 specification and H7 tolerance means this gauge provides a clear, standardised pass/fail decision for small bores. A properly specified limit gauge replaces time-consuming measurement routines with an immediate assessment: the part either accepts the “go” end or is stopped by the “no‑go” end. This approach reduces inspection time, simplifies production workflows and helps prevent costly rework by detecting out‑of‑tolerance bores at the point of manufacture. The design is tailored to frequent use where repeatability and unambiguous results are required. Robust construction for repeatable performance Made from hardened gauge steel, the inspection pin offers elevated wear resistance and dimensional stability under frequent handling. The compact mass (approx. 0.1 kg) and solid geometry keep deflection minimal during insertion, so readings remain consistent across many cycles. Such material choice is common for gauges intended for everyday shop‑floor use because it withstands abrasion and preserves the critical diameter over long service intervals. Regular visual checks and light lubrication will prolong service life and maintain reliable function for production control. Simple to integrate into process control The compact, single‑purpose format supports workflow efficiency: use the go/no-go characteristic for rapid inspection at stations, in fixture checks or at receiving. The clear pass/fail method makes operator training straightforward and reduces subjective interpretation of results. Supplied under the Metav IndustryLine designation M314.004, this inspection tool integrates smoothly into quality documentation systems where quick verification is required repeatedly rather than full dimensional measurement with calipers or gauges. Confidence through a dedicated precision partner Sourcing the gauge from Metav IndustryLine connects the tool to a broader service of stock, traceability and product range that helps streamline procurement. Metav’s focus on democratising precision and its extensive catalogue mean high‑accuracy tools are accessible to workshops and industrial buyers alike. The result is dependable availability and a single partner for complementary inspection equipment, simplifying supply chains and supporting consistent quality control across production. For supply or tailored advice on Metav IndustryLine gauges such as the M314.004, request a quote or technical clarification from Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M314.004 GTIN: 4054469121338 ECLASS: 21170218 Data Diameter: 4.00 mm Weight: 0.1 kg Tariff number: 90173000 Special features Material: hardened gauge steel Standard: DIN 2245 Category: Messstifte; Lehren FAQ What tolerance class does this gauge check? The limit plug gauge checks bore tolerance H7 in accordance with DIN 2245; the M314.004 provides a clear go/no‑go assessment for H7 fits. Is the gauge suitable for production inspection? Yes — the M314.004 is designed for fast pass/fail checks on the production line and for incoming inspection where rapid verification is required. What material is the tool made from? The inspection pin is manufactured from hardened gauge steel, chosen for wear resistance and dimensional stability under frequent use. How should the gauge be stored and handled? Store the gauge in a dry, clean environment, protect it from impacts and corrosive agents, and perform light maintenance such as cleaning and occasional lubrication to preserve the 4.00 mm measuring surface. Can this gauge replace full dimensional measurement? A limit plug gauge like this provides unambiguous pass/fail verification; it complements but does not substitute for full dimensional analysis when documented measurement traceability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4,84mm Prüfstift, Länge 50 mm, ±0,001 mm, Werkstatt-Ausführung, Spezial-Stahl, Lieferung in Kasten - Metav IndustryLine
Der Prüfstift bietet eine verlässliche Kombination aus konstanter Präzision und robuster Werkstatt-Ausführung: Mit einer Messgenauigkeit von ±0,001 mm und einer Länge von 50 mm eignet sich dieses Werkzeug besonders für exakte Endmaßkontrollen. Bestellen Sie den Prüfstift direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Prüfstift M323.484 – Prüfstift, einzeln 4,84 mm Der Prüfstift M323.484 ist ein einzelner, hochpräziser Prüfstift für Endmaße und Feinmessungen in Werkstatt und Produktion. Prüfstift »M323.484« mit Präzision ±0,001 mm Länge 50 mm für Endmaßkontrollen Werkstatt-Ausführung aus Spezial-Stahl Lieferung in transportabler Kiste Mikro‑Klasse für feinmechanische Anwendungen Höchste Präzision für Endmaßkontrollen Der Prüfstift liefert mit einer Genauigkeit von ±0,001 mm reproduzierbare Ergebnisse, die in der Feinmechanik und bei Endmaßprüfungen entscheidend sind. Durch die enge Toleranz wird sichergestellt, dass Passungen und Montageflächen präzise beurteilt werden können. Anwender profitieren von der reduziertem Nacharbeit, da Abweichungen frühzeitig erkannt werden. Die kompakte Bauform unterstützt schnelle Wechsel in Prüfaufbauten und erleichtert das Handhaben in beengten Messumgebungen. Robuste Werkstattqualität durch Spezial‑Stahl Die Werkstatt-Ausführung setzt auf widerstandsfähigen Spezial‑Stahl, der Verschleiß minimiert und lange Maßhaltigkeit gewährleistet. Dadurch bleibt die Formtreue auch bei häufiger Benutzung erhalten, was Standzeiten und Ersatzteilbedarf reduziert. Das Materialverhalten sorgt für zuverlässige Oberflächeneigenschaften an den Messflächen; abrasive Beanspruchung wird besser vertragen als bei Standardwerkstoffen. Geeignet für feinmechanische Prüfaufgaben Mit einem Messbereich von 4,84 mm gehört der Prüfstift zur Mikro‑Klasse, die für feinmechanische Arbeiten und Präzisionsbauteile optimiert ist. Diese Größe ist ideal für Uhrmacher-, Feinwerkzeug‑ und Elektronikapplikationen, in denen kurze Messwege hohe Steifigkeit ermöglichen. Die Länge von 50 mm bietet genug Einspann- und Handhabungsspielraum, ohne die Stabilität bei der Messung zu beeinträchtigen. Effiziente Handhabung und sicherer Transport Zur Auslieferung gehört eine transportable Kiste, die den Prüfstift beim Versand und bei kurzen Transportwegen schützt. Die kompakte Verpackung vereinfacht die Lagerung in mobilen Messkoffern und auf Werkbänken. Das geringe Gewicht und die praktische Länge ermöglichen einen schnellen Einsatz in Prüfvorrichtungen ohne aufwändige Umrüstvorgänge. Empfehlung: Den präzisen Prüfstift M323.484 zur standardisierten Endmaßkontrolle in Fertigung und Werkstatt direkt über Metav Werkzeuge beziehen und bei Bedarf technische Details mit unserer Beratung klären. Produktmerkmale Bezeichnung: Prüfstift, einzeln, 4,84mm, +/- 0.001 mm Länge 50 mm SKU: M323.484 Marke: Metav IndustryLine GTIN: 4061905057809 eCl@ss: 21170231 Zahlen Messbereich (max): 4,84 mm Länge: 50 mm Genauigkeit: ±0,001 mm Gewicht: 0,01 kg Besonderheiten Material: Spezial‑Stahl Werkstatt‑Ausführung Lieferung: transportable Kiste für sicheren Versand FAQ Für welche Anwendungen eignet sich der Prüfstift M323.484 besonders? Der Prüfstift M323.484 ist für feinmechanische Endmaßkontrollen und Präzisionsprüfungen konzipiert und eignet sich besonders für Uhrmacher‑, Elektronik‑ und Feinwerkzeuganwendungen. Welche Messgenauigkeit liefert der Prüfstift? Der Prüfstift M323.484 verfügt über eine Messgenauigkeit von ±0,001 mm, wodurch er hohe Anforderungen an Passungs‑ und Maßprüfungen erfüllt. Wie wird der Prüfstift geliefert? Der Prüfstift wird in einer transportablen Kiste ausgeliefert, die Schutz beim Versand und bei der Lagerung bietet. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4-5mm Ceramic Gauge Pin Set 0.01mm Steps, Antimagnetic Stainless Zirconia, Plastic Case - Metav IndustryLine
The combination of zirconia ceramic construction, sub‑micrometre accuracy and a practical 50 mm workshop length makes this set an ideal choice for demanding inspection tasks. Benefit from wear‑resistant, non‑magnetic pins and a compact plastic case for safe storage; order directly through Metav Werkzeuge or consult the team for application advice. Ceramic test pin set — 4.00–5.00 mm, 0.01 mm step (Metav IndustryLine) Ceramic test pin set, 4.00–5.00 mm, 0.01 mm step is a compact inspection kit engineered for micro‑range dimensional checks in precision workshops and metrology benches. Zirconia ceramic, corrosion‑resistant and non‑magnetic High hardness HV 1250, wear‑resistant tips Accuracy better than ±0.0015 mm per pin Precision for critical inspection tasks The Ceramic test pin set delivers repeatable results in narrow bore and pin‑gauge applications thanks to a fine 0.01 mm graduation across the 4.00–5.00 mm range. With an indicated accuracy of < ±0.0015 mm, the kit supports precise verification of holes, ferrules and mating parts where standard gauges lack the required resolution. The pins’ HV 1250 hardness reduces profile wear and prolongs service life, so measurements remain reliable over many inspection cycles. Durable design optimised for workshop use Constructed from zirconia ceramic, the pins are inherently non‑magnetic and highly wear‑resistant, making them suitable where metal contamination or magnetic interference must be avoided. The workshop version includes 50 mm‑long pins and a secure pin holder, which together provide comfortable handling and controlled insertion depth during measurement. Supplied in a compact plastic case, the set is convenient to transport between bench and machine while protecting individual pins from damage. Practical benefits and typical applications The set of 101 steps in 0.01 mm increments supports fine adjustment and stepwise verification during assembly, quality control and toolmaking. Typical uses include inspection of precision bores, gauge setting, and verification of pin fits in small assemblies. The non‑magnetic ceramic material also suits environments involving sensitive electronic components or magnetic field‑sensitive processes. Overall, the kit offers a pragmatic balance of long‑term durability, compact handling and the measurement resolution required for micro‑range quality assurance. Choose Metav IndustryLine for robust micro‑range testing — contact Metav Werkzeuge for technical consultation and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M318.594 Designation: Ceramic test pin set, 4.00–5.00 mm, 0.01 mm step Manufacturer: Metav IndustryLine Numbers / Core technical data Set count: 101 items Pin length: 50 mm Measurement range: 4.00–5.00 mm Step/increment: 0.01 mm Hardness: HV 1250 Nominal accuracy: < ±0.0015 mm Special features / Materials Material: zirconia ceramic Properties: corrosion‑resistant, non‑magnetic, wear‑resistant Delivery: with pin holder, in plastic case Version: workshop execution FAQ What measurement range does the set cover? The kit covers the 4.00–5.00 mm range in 0.01 mm increments, intended for micro‑range inspections. How accurate are the individual pins? Each pin is specified with an accuracy of better than ±0.0015 mm, allowing precise checks in tight‑tolerance applications. Is the material suitable for magnetic‑sensitive parts? Yes, the zirconia ceramic construction is non‑magnetic, making the set suitable for use with magnetic‑sensitive components. How is the set supplied and stored? The pins are supplied as a complete set with a pin holder and a protective plastic case for secure storage and transport. Which SKU should be ordered for this product? Order using SKU M318.594 for the Metav IndustryLine ceramic test pin set. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4-5mm Test Pin Set 101 Pieces 70mm Length 0.01mm Graduation in Case - Metav IndustryLine
The product data contains inconsistencies: the gross and net prices conflict (preis 442 vs preis_netto 443), indicating a discrepancy that needs to be addressed to ensure accurate pricing information. Additionally, the item count is inconsistent, as the label states 100 pieces while the piece count field indicates 101. This mismatch could lead to confusion or errors in inventory management or customer orders. It is important to verify the source data thoroughly to identify the root cause of these issues and correct them promptly. Ensuring consistency in product data is crucial for maintaining reliability and trust in the system.
4.01-5 mm Gauge Pin Set 100-Piece 0.01 mm Steps Plastic Case - Metav IndustryLine
Take advantage of reliable diameter verification with 0.01 mm step resolution and an accuracy of ±0.002 mm, combined with robust special steel construction and secure transport packaging; order the set directly via Metav Werkzeuge or consult our experts for application advice. Gauge pin set 4.01–5.00 mm, 0.01 mm step — Metav IndustryLine The Gauge pin set 4.01–5.00 mm, 0.01 mm step is a precision toolset for tight-tolerance diameter checks in toolrooms, production inspection and quality control applications. High-precision 0.01 mm increments Range 4.01–5.00 mm for fine tolerances Hardened special-steel pins Delivered in sturdy transport case Repeatable accuracy for diameter verification Gauge pins are the simplest and most reliable method for diameter verification when reproducible tolerances are required. This set offers 0.01 mm increments across the nominal 4.01–5.00 mm range and an indicated accuracy of ±0.002 mm, which supports fast, objective go/no-go checks and precise fitment trials. The combination of fine stepping and tight accuracy reduces measurement uncertainty and shortens inspection cycles, delivering a clear productivity advantage in standardised testing workflows. Workshop-ready durability and organisation Constructed from special steel, the pins provide resilient wear resistance for routine contact checks and frequent handling. The set is supplied in a sturdy transport case that keeps items organised and protected during storage and transit; this maintains traceability and reduces downtime spent searching for the correct gauge. With a compact pin length of 50 mm, the components are well suited to confined inspection stations and bench-mounted fixtures while remaining simple to clean and inspect, which supports consistent quality control practices. Practical use and integration into inspection routines Designed for dimensional verification of turned, milled and ground components, the set supports both manual and fixture-based testing. The pins are ideal for assembly clearance checks, plug gaging and comparative measurement tasks where a definite, measurable limit is required. When traceable records are needed, the clear organisation of the set simplifies documentation and reduces the risk of mix-ups in batch inspections. For bespoke measurement sequences, the set integrates with existing inspection jigs and bench equipment without modification. For ordering or technical consultation on the Metav IndustryLine gauge pin set, contact Metav Werkzeuge in Emmerich for tailored advice and availability: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M318.554 GTIN: 4054469129372 Tariff number: 90173000 Manufacturer: Metav IndustryLine Facts Range: 4.01–5.00 mm Increment: 0.01 mm Accuracy: 0.002 mm Pin length: 50 mm Weight (set): 2.3 kg Pieces per set: 100 Special features Material: Special steel Delivered in transport case for safe handling and transport Category: Gauge pins / precision gaging Suitable for diameter verification and go/no-go checks FAQ What measurement precision does this set provide? The set achieves step resolution of 0.01 mm with a stated accuracy of ±0.002 mm, making the Gauge pin set 4.01–5.00 mm, 0.01 mm step (M318.554) appropriate for fine-tolerance inspection. How is the set supplied and stored? The pins are supplied in a sturdy transport case to protect the tools during transit and storage; the case maintains order and supports traceable inspection routines for the Metav IndustryLine set. Can these pins be used for assembly clearance checks? Yes — the set is designed for practical assembly and fitment trials, providing defined reference diameters for go/no-go and clearance testing in production and maintenance environments. What material are the pins made from and how does that affect use? Pins are manufactured from special steel, offering good wear resistance and robustness for repetitive contact inspections without rapid degradation. Is the set suitable for bench fixtures and jigs? The compact 50 mm pin length and standard diameter steps make the set compatible with most bench fixtures, plug gages and simple inspection jigs used in toolrooms and workshops. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.01mm Gauge Pin, Workshop Version, 50mm Length, ±0.001mm Accuracy - Metav IndustryLine
Take advantage of a combination of industrial accuracy and robust workshop design: the 4.01 mm diameter with ±0.001 mm tolerance and a 50 mm length ensure reproducible go/no‑go checks, while the special steel construction resists wear during frequent handling. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.401 gauge pin, 4.01 mm — Workshop test pin with ±0.001 mm accuracy (Metav IndustryLine) The M323.401 gauge pin is a workshop-grade test pin intended for precise dimensional checks and fixture verification in production and inspection environments. Workshop-grade construction Diameter 4.01 mm, tolerance ±0.001 mm 50 mm hardened special steel Supplied in protective transport case Dependable accuracy for routine inspection The gauge pin offers ±0.001 mm tolerance, delivering a level of precision suitable for critical inspection tasks and fine adjustment of jigs and fixtures. Such a narrow tolerance reduces measurement uncertainty and supports consistent quality control across batches. Where repeatable go/no‑go verification is required, the pin’s nominal 4.01 mm diameter provides a clear reference that simplifies pass/fail decisions and shortens inspection cycles, improving throughput without compromising traceability. Built for continual workshop use Manufactured from special steel and produced in a workshop specification, the pin balances surface hardness with resistance to chipping under frequent insertion and withdrawal. The 50 mm length provides sufficient engagement for many fixture and bore checks while remaining compact and easy to handle at the bench. The robust material choice and finish reduce wear, so calibration drift is minimised and replacement intervals are extended — a practical cost advantage in everyday production. Practical handling and storage Delivered as a single gauge pin and packed in a protective transport case, the component is protected during storage and transit, helping to preserve its sensitive tolerance. The modest mass contributes to easy manipulation during repetitive tests and quick set‑up when changing inspection points. The compact format also facilitates organised storage alongside other measuring tools, supporting orderly workflows on the shop floor and in measurement rooms. How this supports efficient production Using a precisely manufactured gauge pin for end‑dimension checks removes ambiguity from go/no‑go decisions and reduces rework caused by marginal fits. The simple geometry of the pin permits rapid verification of bores, locating holes and fixture alignment without complex instrumentation, enabling operators to maintain steady output with reliable quality feedback. Combined with Metav’s logistics and product range, the pin helps maintain continuous supply for inspection stations. For project enquiries, stock information or advice on integrating this Metav IndustryLine gauge pin into existing inspection routines, contact Metav Werkzeuge for personalised support and delivery options. Technical data Article number: M323.401 GTIN: 4061905057281 Brand: Metav IndustryLine Material: Special steel Diameter: 4.01 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.007 kg Packaging: Protective transport case Facts Length: 50 mm Diameter nominal: 4.01 mm Tolerance: ±0.001 mm Weight: 0.007 kg Special features Workshop execution Single gauge pin for end‑dimension checks Supplied in a transport case GTIN recorded FAQ What is the intended application of this gauge pin? The M323.401 gauge pin from Metav IndustryLine is designed for go/no‑go checks, bore verification and fixture alignment where a 4.01 mm reference is required. How precise is the M323.401 gauge pin? The pin provides a tolerance of ±0.001 mm, enabling high reproducibility for routine inspection and pass/fail assessment. What material is the pin made from and why does that matter? The gauge pin is made of special steel, chosen to combine surface hardness and durability so the Metav IndustryLine pin withstands frequent use without rapid wear. Is the pin supplied individually or in a set? This SKU is supplied as a single gauge pin (single piece) and is packaged in a protective transport case for safe storage and handling. Can the M323.401 be used for fixture set‑up on the shop floor? Yes — its workshop specification and compact 50 mm length make it suitable for rapid fixture alignment and on‑machine checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.02mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, micrometre-level accuracy and compact handling for reliable end‑dimension inspection; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.402 — single precision pin, 4.02 mm ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.402 is a workshop-grade precision pin intended for end‑dimension checks and small‑bore verification in assembly and quality control environments. Workshop-grade precision Tolerance ±0.001 mm Diameter 4.02 mm 50 mm length for compact handling Precision that reduces rework and inspection time The single test pin delivers micrometre-level repeatability thanks to its specified ±0.001 mm tolerance, making it suitable where tight end‑measurements matter. Manufactured in special steel, the pin maintains roundness and dimensional stability under routine handling, which reduces measurement scatter and subsequent rework. As a single‑piece reference tool, the component acts as a reliable control for pass/fail checks and small‑bore verification in production or incoming‑goods inspection, supporting faster decisions on conformity and process adjustments. Built for workshop measurement tasks and tight spaces With a 4.02 mm diameter and a 50 mm length, the pin is compact enough for use in confined fixturing and assembly jigs while still offering an ergonomic grip for manual handling. The workshop construction is aimed at everyday use: the pin withstands repeated insertion and withdrawal cycles without compromising the calibrated diameter. This combination of size and robustness enables pragmatic measurement routines in toolrooms and maintenance departments, where straightforward, fast checks prevent costly production interruptions. Traceability, inventory ease and practical integration The component is supplied with a clear identifier (SKU M323.402 and GTIN) that simplifies stock management and traceability in quality systems. Its modest mass supports safe handling and fast placement into gauges or test benches. As a defined end‑measurement reference, the pin integrates well with master sets or reference kits and helps to standardise dimensional checks across shifts and sites. Choosing a clearly specified, single‑diameter reference reduces ambiguity in inspection protocols and supports consistent reporting across the workshop. Contact Metav Werkzeuge for advice on integrating the M323.402 gauge pin into existing inspection routines or for assistance with procurement and batch needs Technical data Article number: M323.402 GTIN: 4061905057298 Manufacturer: Metav IndustryLine Numbers Diameter: 4.02 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.007 kg ECLASS: 21170231 Special features Material: Special steel Workshop version Single test pin for end‑dimension checks FAQ What applications is this gauge pin intended for? The M323.402 gauge pin is intended for end‑dimension inspection, small‑bore verification and routine workshop pass/fail checks in mechanical assembly and quality control. Is the diameter tolerance sufficient for precision assembly gauges? Yes; the ±0.001 mm tolerance of the M323.402 pin meets high‑precision requirements and is suitable as a reference in critical assembly and inspection tasks. Can the pin be used as a reference in master sets? The robust workshop construction and precise diameter make the pin a suitable single‑element reference for master kits and standardised inspection procedures. How does the M323.402 support inventory and traceability? The item is provided with SKU M323.402 and GTIN 4061905057298, which facilitate stock control and traceability within quality management systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.03mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of razor‑tight ±0.001 mm tolerance, a precise 4.03 mm diameter and robust special steel construction for repeatable end‑measurement in production and inspection. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.403 — 4.03 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.403 designed for precise end‑measurement and go/no‑go checks in workshop inspection and quality control applications High‑precision ±0.001 mm tolerance 4.03 mm diameter for end‑measurements 50 mm hardened length for stable seating Workshop execution for daily use Precision that protects production With a nominal diameter of 4.03 mm and a declared tolerance of ±0.001 mm, this gauge pin delivers the dimensional certainty required for final inspection and tight‑tolerance assemblies. The 50 mm length provides a stable reference when checking bores, dowel seats or mating parts, reducing ambiguity in go/no‑go assessments. Made from special steel, the pin resists wear under frequent use so that measurement results remain reproducible and process decisions can be made on a solid factual basis. Designed for robust workshop handling The workshop execution of this test pin combines a compact form with a surface and hardness profile suited to regular use on inspection benches. As a single‑piece deliverable, it simplifies inventory and replacement routines while its low mass (approx. 0.007 kg) supports quick manual handling during multi‑point checks. The straightforward geometry minimises seating errors and accelerates cycle times during incoming inspection or in‑process verification, translating precision into measurable time savings. Fits practical quality workflows Integration into standard inspection procedures is effortless: the gauge pin is ideal for end measurements, alignment checks and functional testing of press fits or dowel holes. Traceability is supported by the clear article identifiers and industry classification included in the technical data, which aids documentation and quality records. Using a dedicated gauge pin with this tolerance level lowers the risk of rework, improves first‑pass yield and stabilises downstream processes — a rational advantage for production teams focused on efficiency and scrap reduction. For procurement or technical guidance on Metav IndustryLine measuring tools, contact Metav Werkzeuge in Emmerich for expert advice and fast supply coordination Technical data Article number: M323.403 GTIN: 4061905057304 Category: Messstifte EClass: 21170231 Facts Diameter: 4.03 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.007 kg Special features Material: Special steel Delivery: single piece Execution: Workshop version Application: End measurements and go/no‑go checks FAQ What materials is this gauge pin suitable for? This gauge pin is manufactured from special steel and is intended for dimensional checks on metallic components where a hardened, wear‑resistant reference is required. Is the tolerance of ±0.001 mm sufficient for precision assembly controls? Yes, the ±0.001 mm tolerance of the M323.403 provides the accuracy expected for tight assembly fits and final inspection in many production environments. Does the item come as a single piece or in sets? The product is supplied as a single piece; the article number M323.403 identifies a single gauge pin for straightforward stock management. Can this gauge pin be used for both bores and dowel seats? The geometry and length of the pin make it suitable for end‑measurements in bores and dowel seats, providing a reliable datum for go/no‑go assessments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com