Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
4.52mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, 4.52 mm nominal diameter and a robust 50 mm length for reliable end‑dimension verification; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.452 — 4.52 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.452 is a single, workshop‑grade test pin designed for precise end‑dimension checks and fit verification in inspection and assembly workflows. Diameter 4.52 mm for precise fits Tolerance ±0.001 mm for submicron control 50 mm hardened test pin length Workshop‑grade special steel construction Precision that reduces rework and inspection time Manufactured to a tight ±0.001 mm tolerance on a 4.52 mm nominal diameter, this test pin provides the dimensional certainty required in fine inspection tasks. The very small tolerance reduces measurement uncertainty and supports consistent pass/fail decisions at the control station, minimising rework and downtime. For users unfamiliar with tolerance levels: ±0.001 mm denotes a variation of one micrometre, which is comparable to the thickness of a fine human hair and is suitable where high repeatability is essential. Durable design for everyday workshop use Built as a workshop‑grade component from special steel, the pin balances hardness and toughness to withstand repeated insertion and extraction in jigs, bushings and mating bores. The 50 mm overall length provides ample engagement depth for stable reference contact without excessive overhang, while the low mass supports quick handling and alignment during routine checks. These material and dimensional choices translate directly into longer life, fewer replacements and predictable behaviour under mechanical stress. Practical handling and application scenarios Supplied as a single test pin for direct use in verification tasks, this gauge pin is ideal for end‑dimension checks, assembly go/no‑go fixtures and finish‑control operations where precise fit is critical. The compact diameter and hardened surface make it suitable for confirming bore sizes, verifying plug fits and establishing reference points during final inspection. The part is particularly useful where accurate end‑measurements ("end dimensions") determine final acceptance further down the production line. Why Metav IndustryLine is the pragmatic choice Metav IndustryLine items combine focused technical design with the supply assurance expected by workshops and production facilities. Metav's Emmerich hub acts as a quality filter for the European market, supporting consistent stock levels and traceable product information. Choosing components from this range means selecting practical accuracy that integrates into established inspection routines, backed by a distributor experienced in industrial metrology. Contact Metav Werkzeuge for tailored application advice on the Metav IndustryLine gauge pins and to ensure prompt availability from the Emmerich distribution hub Technical data Article number: M323.452 GTIN: 4061905058004 Label: Prüfstift, einzeln, 4,52mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 4.52 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Special features Material: Special steel Workshop execution Single test pin Category: Messstifte FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 4.52 mm with a tolerance of ±0.001 mm for ultra‑fine measurement control. Is this item supplied as an individual piece or part of a set? The M323.452 is supplied as a single test pin intended for individual use in verification and assembly checks. Which applications are best suited to this test pin? This test pin is suited to end‑dimension verification, bore and plug fits, and final inspection tasks where precise fit confirmation is required. What material is used for the pin and why does it matter? Manufactured from special steel, the pin offers a balance of hardness and wear resistance that supports repeated workshop use without rapid degradation. Can the pin be used in automated gauging fixtures? Yes, the form and tolerance of the pin make it suitable for integration into mechanical gauging and fixture systems that require consistent reference dimensions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.53mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, robust workshop design and protected transport for reliable end‑measurement checks; order the component via Metav Werkzeuge or contact our advisors for application guidance. Gauge pin M323.453 — single gauge pin, 4.53 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The gauge pin M323.453 is a workshop‑grade, high‑precision reference pin for end‑measurement checks and fixture set‑up in metalworking and quality control Workshop version, robust for daily shop use Diameter 4.53 mm with ±0.001 mm tolerance Delivered in protective transport case Repeatable precision for critical end measurements The pin offers ±0.001 mm tolerance on a 4.53 mm nominal diameter, delivering a stable reference for tight‑tolerance checks. This level of accuracy reduces ambiguity when verifying end dimensions and setting gauges, helping to maintain consistent part quality across batches. The moderate 50 mm length provides a practical reach for common fixture work while keeping handling straightforward and repeatability high. Built for the workshop: material and protection Manufactured in special steel, the pin is engineered for everyday metrological use without compromising surface integrity. The workshop‑grade finish resists wear from repeated insertion and removal, while the supplied protective transport case ensures pins remain undamaged in transit and storage. The compact design balances stiffness and ease of handling, supporting reliable seating in bores and jigs during routine inspections. Practical integration into quality workflows As a single‑item reference from Metav IndustryLine, this pin suits quick go/no‑go assessments, fixture alignment and comparative bore gauging. The clear nominal value and tolerance simplify documentation in control plans and inspection reports. Supplied as a standalone precision pin (SKU M323.453), it complements sets or bespoke jigs and can be introduced into existing measurement routines with minimal training. Contact Metav Werkzeuge for availability of the M323.453 gauge pin and tailored advice from our Emmerich specialists—email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific end‑measurement tasks Technical data Article number: M323.453 GTIN: 4061905058011 Category: Messstifte Specifications Diameter: 4.53 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Materials & features Material: Special steel Workshop execution Supplied in protective transport case (plastic or wooden) Single gauge pin for end measurements FAQ What is the nominal diameter of this gauge pin? The gauge pin M323.453 has a nominal diameter of 4.53 mm. What accuracy can be expected from the pin? The Metav IndustryLine M323.453 is manufactured to a tolerance of ±0.001 mm, suitable for high‑precision end‑measurement checks. Which material is used for the pin? The pin is made from special steel and finished for workshop use to resist everyday wear. Is the pin delivered with protective packaging? Yes, the M323.453 is supplied in a protective transport case (plastic or wooden) to prevent damage during transport. How is the pin typically used in a workshop? Typical applications include fixture set‑up, bore gauging and quick reference checks for end measurements in machining and inspection processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.54mm Precision Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of ultra‑tight ±0.001 mm accuracy combined with a 4.54 mm diameter and a durable 50 mm length to secure reproducible end‑dimension checks in production and inspection. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin M323.454 — precision inspection pin, 4.54 mm, ±0.001 mm, 50 mm The gauge pin M323.454 is a single inspection pin designed for exacting dimensional checks and end‑measure verification in metrology and workshop quality control. High precision ±0.001 mm tolerance Diameter 4.54 mm, ground profile 50 mm functional length for fixtures Workshop version in special steel Consistent dimensional certainty for quality control High repeatability in inspection processes reduces rework and scrap. The ±0.001 mm tolerance of this inspection pin corresponds to a 1 µm margin, enabling extremely fine discrimination between conforming and non‑conforming parts. Where batch acceptance depends on reliable go/no‑go evaluation, the tight specification ensures that measurements are traceable, precise and directly comparable across shifts and operators. The fine tolerance is particularly beneficial where small deviations have a significant effect on assembly fit or functional clearance. Efficient integration into inspection routines Designed as a single, ready‑to‑use inspection element, the pin supports fast, repeatable checks at gauges, fixtures and assembly stations. The 4.54 mm diameter and 50 mm length make the pin suitable for probing bores, alignment dowels and plug checks without the need for additional adapters. The compact geometry simplifies handling and speeds up measurement cycles, contributing to throughput improvements in incoming inspection and in‑process quality control. Where time is critical, the practical dimensions permit rapid insertion and stable seating, shortening inspection lead times. Robust material choice and handling benefits Manufactured from special steel, the pin combines wear resistance with dimensional stability under routine workshop conditions. The ground profile promotes defined contact points for precise measurement transfer and minimises surface deformation during use. At a mass of approximately 0.009 kg, the component is easy to position and to clamp in test fixtures while maintaining sufficient stiffness for accurate results. This construction supports reliable performance across repeated measurement cycles, sustaining inspection confidence and reducing uncertainty in final dimension verification. For tailored application advice or to order the M323.454 gauge pin, contact Metav Werkzeuge in Emmerich for direct supply and technical support at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.454 GTIN: 4061905058912 Brand: Metav IndustryLine Facts Diameter: 4.54 mm Tolerance/Accuracy: ±0.001 mm Length: 50 mm Weight: 0.009 kg Eclass: 21170231 Special features Single inspection pin delivery Material: special steel Workshop execution Intended for end‑dimension checks FAQ What level of accuracy does this inspection pin provide? The inspection pin M323.454 offers an accuracy of ±0.001 mm, equivalent to 1 µm, making it suitable for high‑precision dimensional checks. Can the pin be used for bore and alignment checks? Yes. The 4.54 mm diameter and 50 mm functional length make the pin suitable for probing bores, alignment dowels and fixture checks in workshop and inspection contexts. What material is the pin made from and why does that matter? The pin is made from special steel, chosen for its wear resistance and dimensional stability; this supports repeated measurements without rapid degradation of the contact surface. Is the M323.454 appropriate for automated inspection stations? The compact geometry and defined ground profile enable integration into many fixture and gauge setups; the M323.454 can be used in semi‑automated processes where a stable reference pin is required. How should the pin be stored to preserve accuracy? Store the pin in a clean, dry environment and protect the ground ends from impact and contamination; preserving the contact surfaces maintains the stated ±0.001 mm accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.55mm Gauge Pin Single ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Precise bore verification with a 4.55 mm diameter, ±0.001 mm tolerance and 50 mm length provides repeatable inspection results; the workshop‑grade special steel construction and supplied transport case protect the reference pin in daily use. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for technical advice. Gauge pin, single — 4.55 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The Gauge pin, single, 4.55 mm, ±0.001 mm, length 50 mm is a precision reference pin for bore checking and end‑dimension verification in workshop metrology. High‑precision tolerance ±0.001 mm Diameter 4.55 mm with 50 mm length Special steel, robust workshop version Supplied in protective transport case Measurement confidence at micrometre level The extremely fine ±0.001 mm tolerance places this reference pin in the category of high‑precision workshop gauging tools. Such a narrow tolerance reduces uncertainty during pass/fail checks and improves acceptance reproducibility when used as a reference in plug gauges or inspection fixtures. By providing a stable diameter of 4.55 mm, the pin supports repeatable internal diameter checks, minimising rework and ensuring parts meet tight end‑mass requirements. Traceable identification via the SKU and GTIN assists in documentation and quality records. Built for daily workshop use and secure handling Constructed from special steel and labelled as a workshop version, the pin tolerates routine handling while maintaining surface integrity essential for accurate gauging. With a nominal length of 50 mm and a weight of approximately 0.009 kg, it is easy to position and manipulate within small bores or test assemblies. Delivery in a dedicated transport case protects the reference surface during storage and transit, preserving the calibrated geometry and prolonging service life under shopfloor conditions. Seamless integration into inspection routines This single gauge pin works effectively as a reference element in modular inspection setups, plug gauges and manual measurement benches. Its compact form and precise geometry make it suitable for end‑dimension verification and use as an endmass in comparative checks. The clear specification and GTIN support inventory control and traceability across production batches. For projects that require documentation or tailored measurement strategies, the Metav distribution network provides local availability and technical guidance to integrate the pin into existing quality workflows. Choose Metav IndustryLine’s M323.455 for reliable bore checks and ask Metav Werkzeuge for application guidance or procurement details at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.455 GTIN: 4061905058929 Label: Gauge pin, single, 4.55 mm, ±0.001 mm, length 50 mm Numbers / Core technical data Diameter: 4.55 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Material: Special steel Special features Workshop version Supplied in transport case for protection during transport Single gauge pin for bore and end‑dimension checks Category: Gauge pins (Messstifte) FAQ What is the primary use for this gauge pin? The gauge pin is intended as a precision reference for bore inspections and end‑dimension verification in workshop and inspection contexts; the M323.455 is suited to plug‑gauge and comparative checks. How tight is the manufacturing tolerance and what does it mean in practice? A tolerance of ±0.001 mm denotes micrometre‑level conformity, enabling highly reproducible pass/fail evaluations and reducing measurement uncertainty in routine inspection tasks. Is the pin protected for transport and storage? Yes, the M323.455 is supplied in a protective transport case to preserve the reference surface and maintain measuring accuracy during handling and storage. Can this pin be used in modular gauge assemblies? The single gauge pin is suitable for integration into modular inspection fixtures and plug‑gauge setups where a stable, precise reference is required. Which material is used for the pin and why does it matter? Manufactured from special steel, the pin offers wear resistance and dimensional stability, supporting consistent measurement results over prolonged use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.56mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of a precision instrument that combines ultra-fine tolerance with compact dimensions: the 4.56 mm diameter and ±0.001 mm accuracy ensure dependable end‑dimension verification, while the 50 mm length suits common fixture and gauge tasks. Order directly via Metav Werkzeuge or consult our technical team for selection advice. Gauge pin, single, 4.56 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The Gauge pin, single, 4.56 mm, ±0.001 mm, 50 mm is a workshop-grade test pin designed for precise end‑measurement and fixture alignment in inspection and assembly environments High-precision ±0.001 mm tolerance Diameter 4.56 mm for tight fits 50 mm length for fixture and end checks Workshop-grade special steel construction Reliable accuracy for final dimensions A compact inspection tool that delivers repeatable results: the ±0.001 mm tolerance places this pin in the high‑precision category for routine end‑dimension checks. In practice, this fine tolerance reduces measurement variation at the control stage and supports consistent go/no‑go decisions on production lines. The slim 4.56 mm diameter and measured 50 mm length make the component ideal for verifying bore fits, plug gauges and fixture seats without introducing handling‑related error. Built for everyday workshop use The workshop execution and special steel construction prioritise durability under frequent handling. This robustness minimises deformation over repeated use and helps maintain calibration intervals, supporting continuous operation in busy inspection areas. The light mass (approx. 0.009 kg) eases manual placement in confined setups and contributes to stable seating in gauges and fixtures, reducing operator fatigue during repetitive checks. Practical role in quality workflows Designed as a straightforward dimensional reference, this test pin assists in end‑measurement, fixture set‑up and quick functional checks where a small, highly accurate datum is required. Integration into inspection routines is simple: the pin complements calipers and coordinate measurements by providing a fast mechanical check for critical fits. The Metav IndustryLine identification (SKU M323.456) aids traceability in stores and inspection reports while supporting consistent component acceptance criteria. For workshop applications requiring high‑precision end checks, contact Metav Werkzeuge for availability and tailored technical advice on the Metav IndustryLine gauge pin M323.456 Technical data Article number: M323.456 GTIN: 4061905058936 Manufacturer: Metav IndustryLine Facts Diameter: 4.56 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Special features Material: Special steel Workshop version Single gauge pin for end measurements Suitable for fixture and plug checks FAQ What level of precision does this gauge pin provide? The gauge pin M323.456 from Metav IndustryLine offers an accuracy of ±0.001 mm, suitable for high‑precision end‑dimension verification. Can this pin be used for plug and bore checks? Yes, the 4.56 mm diameter and 50 mm length make the pin suitable for plug and bore verification as part of fixture and assembly checks. Is the material suitable for repeated workshop use? The test pin is made from special steel in a workshop execution designed to withstand frequent handling while preserving dimensional stability. How is the product identified for inventory and documentation? The item is listed under SKU M323.456 and GTIN 4061905058936, which supports traceability in inspection records and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.57mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of workshop-ready precision and robust construction combined with compact handling for reliable end‑dimension checks; order this inspection component directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.457 — 4.57 mm, ±0.001 mm (Metav IndustryLine) A gauge pin M323.457 designed for precise end‑dimension verification in workshop and inspection routines. Workshop version for robust use Diameter 4.57 mm, precision ±0.001 mm Length 50 mm, compact inspection pin Special steel construction for durability Supplied in protective transport case High‑precision checks with minimal effort For repeatable dimensional control, this inspection pin delivers exceptional precision: a diameter of 4.57 mm held to ±0.001 mm. Such fine tolerance makes the component ideal for verifying end dimensions and fit tolerances where deviations must be kept to a minimum. The tight specification reduces rework and supports faster acceptance testing in small‑batch production, offering a measurable improvement in process stability and part interchangeability. Built for the workshop — tough and dependable Manufactured in special steel and specified as a workshop version, the pin resists routine handling and supports daily use in inspection benches and assembly stations. The compact 50 mm length and low mass provide comfortable handling during multiple checks, while the material choice balances wear resistance with machinability. A protective transport case is included to prevent damage in transit and to keep the gauge ready for immediate use on the shop floor. Practical integration into inspection workflows The single‑piece design suits spot checks, go/no‑go fits and auxiliary verification steps within established quality procedures. Traceability is supported by clear identification: SKU M323.457 and GTIN are assigned for inventory control and documentation. As part of a lean inspection setup, this pin shortens setup time compared with adjustable gauges and provides a simple, unambiguous measurement reference for operators and quality engineers. Handling, storage and measurement context The pin’s small footprint and mass make it convenient for bench use and for storing alongside hand tools. With a mass of 0.009 kg and a length of 50 mm, the component is easy to position and less prone to introducing bending errors compared with longer probes. When used as specified, the pin complements standardised inspection procedures, supports repeatable results and contributes to reliable batch release decisions without the complexity of electronic measuring systems. For workshop‑grade measuring that streamlines inspection tasks, request the Metav IndustryLine gauge pin M323.457 from Metav Werkzeuge — contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 for application guidance and availability. Technical data Article number: M323.457 GTIN: 4061905058943 Category: Messstifte Label: Prüfstift, einzeln, 4,57mm, +/- 0.001 mm Länge 50 mm Core measurements Diameter: 4.57 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Features and handling Material: Special steel Version: Workshop execution Delivery: Protective transport case FAQ What is the nominal diameter and tolerance of this inspection pin? The inspection pin has a nominal diameter of 4.57 mm with a tolerance of ±0.001 mm for precise end‑dimension checks. Is the gauge pin suitable for workshop use and frequent handling? Yes, the Metav IndustryLine gauge pin M323.457 is specified as a workshop version and is manufactured from special steel to withstand regular use. Does this pin come calibrated or with a certificate? This listing does not state a delivered calibration certificate; calibration status is not implied for the gauge pin M323.457 unless explicitly specified elsewhere. Can the pin be used for fit and go/no‑go checks? The single gauge pin is intended for go/no‑go fit verification and end‑dimension inspection as part of conventional quality workflows. How is the product supplied for transport and storage? The inspection pin is supplied in a protective transport case to prevent damage during handling and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.58mm Test Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, a compact 4.58 mm diameter and a stable 50 mm length to secure repeatable end‑measurements and reliable plug‑fitting checks in everyday workshop workflows. Order the part directly via Metav Werkzeuge or consult the team for matching inspection aids and traceability options. Gauge pin M323.458 — 4.58 mm, ±0.001 mm, Metav IndustryLine A gauge pin designed as a single‑piece inspection pin for precise end‑measurement and plug checks in workshop environments. Single gauge pin 4.58 mm diameter Tolerance ±0.001 mm for high precision Length 50 mm for stable engagement Special steel for robustness in the workshop Consistent accuracy for production control The core advantage is the ±0.001 mm tolerance, which enables highly reliable pass/fail checks and repeatable reference measurements on small bores and mating parts. Such fine certainty supports faster decision‑making on the shop floor and reduces rework by catching deviations early. The compact 4.58 mm diameter positions the pin for micro‑fits and precision end‑measurements while maintaining a clearly measurable contact surface. Stable geometry for straightforward handling A 50 mm length gives a comfortable engagement depth that balances rigidity with manoeuvrability: long enough for secure seating in a bore, yet short enough for single‑handed positioning in fixtures. The special steel construction provides wear resistance under regular workshop use, improving service life compared with untreated pins. The workshop configuration is tailored for practical daily use rather than laboratory‑only handling. Simple integration into inspection routines Designed as a single item for insertion and verification tasks, the pin suits common inspection routines such as plug checks, fit tests and reference gauging during assembly. The compact form factor and consistent diameter tolerance make it straightforward to integrate the pin into go/no‑go fixtures or dedicated inspection jigs, supporting efficient cycle times and clear measurement outcomes. Traceability and identification for procurement Identified as M323.458 and listed with GTIN for stock control, the pin is suitable for teams that require traceable part management and quick replacement procurement. Supplied as a single gauge pin, it fits maintenance schedules where individual items are stocked for immediate use and easy substitution, reducing machine downtime and simplifying inventory handling. Contact Metav Werkzeuge for tailored advice on using the Metav IndustryLine M323.458 in existing inspection setups — their specialists in Emmerich can confirm compatibility and help secure the correct inspection aids for the production environment. Technical data SKU: M323.458 GTIN: 4061905058950 Brand: Metav IndustryLine Facts Diameter: 4.58 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Special features Material: special steel Configuration: single gauge pin Intended use: end‑measurement, plug checks Version: workshop execution (Werkstatt‑Ausführung) eClass: 21170231 FAQ What measurement accuracy does this pin provide? The Metav IndustryLine gauge pin M323.458 guarantees a dimensional accuracy of ±0.001 mm, making it suitable for precision plug checks and repeatable end‑measurement tasks. Which inspection tasks is this pin suited for? This single gauge pin is intended for plug‑fitting checks, bore verification and assembly‑fit tests where a compact 4.58 mm diameter and tight tolerance enable reliable go/no‑go assessments. Is the item supplied as a single piece and how is it identified? Yes, the product is supplied as a single gauge pin under SKU M323.458 and carries a GTIN for stock and traceability purposes. What material is used and how durable is the pin? The pin is produced from special steel and configured for workshop use, providing enhanced wear resistance during routine inspection and handling. Can this pin be used directly in production fixtures and jigs? The M323.458 gauge pin is designed for direct integration into fixtures and jigs for go/no‑go and reference checks, offering a compact and stable contact geometry for frequent use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.59mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm manufacturing accuracy, a precise 4.59 mm diameter and a robust 50 mm length for consistent end‑measurement results; delivered as a workshop‑grade tool in a transport case. Order the (test pin M323.459) directly via (Metav Werkzeuge) or ask our consultants if needed. Test pin M323.459 – gauge pin, 4.59 mm diameter, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) A Test pin M323.459 conceived as a workshop‑grade gauge for reliable end measurements and rapid inspection of bores and fits in production and quality control environments. ±0.001 mm tolerance Diameter 4.59 mm nominal 50 mm overall length Workshop‑grade special steel Precision that lowers scrap and rework The pin delivers an exceptional ±0.001 mm tolerance, a level of accuracy that supports tight assembly checks and repeatable inspection routines. Specified as a 4.59 mm nominal diameter and finished to gauge dimensions, the component acts as a direct reference for hole verification and end‑measurement tasks. Using a hardened and ground measuring element reduces uncertainty at the inspection stage, so decisions on part acceptance are founded on verifiable, comparable values rather than approximation. Robust construction for daily workshop use Manufactured in special steel and offered in a workshop version, this gauge pin is built to withstand frequent handling in industrial environments. The 50 mm length provides a stable engagement when measuring through or to a shoulder, balancing reach and rigidity for consistent contact. Supplied in a transport case, the instrument is protected during storage and in transit, preserving calibration and surface finish so that service intervals remain predictable and maintenance effort is minimised. Ready for integration into inspection workflows As a purpose‑made measuring element for end or limit measurement tasks, the gauge pin simplifies routine checks and reduces measurement chain complexity. The compact geometry facilitates use in fixtures, verification benches and manual inspection stations while the catalogued SKU supports traceable procurement and inventory handling. When used as part of a documented inspection plan, this test pin helps maintain process quality and supports reproducible measurement outcomes across shifts and operators. For precision that fits serious workshop standards, choose the Metav IndustryLine test pin M323.459 and contact Metav Werkzeuge in Emmerich for ordering or application advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.459 GTIN: 4061905058967 Manufacturer: Metav IndustryLine (Metav Werkzeuge GmbH) Category: Gauge pins / Messstifte Label: Test pin, single, 4.59 mm, ±0.001 mm, length 50 mm Dimensions & tolerance Nominal diameter: 4.59 mm Overall length: 50 mm Tolerance / accuracy: ±0.001 mm Weight: 0.009 kg Materials & special features Material: Special steel Design: Workshop version Delivery: Supplied in transport case Application hint: Intended for end‑measurement / inspection tasks FAQ What tolerance is guaranteed for this gauge pin? The gauge pin is manufactured to a tolerance of ±0.001 mm, providing the precision required for tight fit and end‑measurement tasks with the Metav IndustryLine M323.459. For which measurement tasks is this pin suitable? This inspection pin is intended for end measurements, bore verification and fit checks where a precise 4.59 mm reference is required; it performs well in manual inspection and fixture use. Is the pin delivered ready for use and protected? The M323.459 is supplied as a workshop‑grade item and comes in a transport case to protect the measuring surface and preserve dimensional integrity during storage and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop-grade ±0.001 mm accuracy and a compact 4.50 mm diameter in a stable 50 mm length for repeatable reference measurements; order the measuring pin directly via Metav Werkzeuge or consult our specialists for integration advice. Measuring pin M323.450 — gauge pin, 4.50 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The Measuring pin M323.450 is a single workshop-grade gauge pin for end‑measurements and reference positioning in inspection jigs and fixture work. Workshop-grade precision ±0.001 mm Diameter 4.50 mm for tight fits Length 50 mm for stable positioning Precision that reduces rework and inspection time The core advantage of this gauge pin is its ±0.001 mm tolerance, which translates into reliable repeatability when checking end dimensions and reference bores. In practical terms, the fine tolerance reduces the need for corrective rework by ensuring that parts meet dimensional requirements at first inspection. The compact 4.50 mm diameter offers a tight fit in gauges and alignment fixtures, while the balanced mass and low weight contribute to stable seating without excessive handling force. Built for workshop demands and robust routine use Designed as a workshop execution component, the pin is manufactured from special steel to withstand frequent insertion and gentle knocks typical in everyday metrology tasks. The 50 mm length gives sufficient bearing surface for consistent seating in holders or gage plates, enhancing positional stability. Durability and simple handling mean fewer interruptions in production and a long service life under regular use, which supports efficient quality control workflows on the shop floor. Clear applications and simple integration into gauges This single gauge pin is aimed at inspection, jig assembly and reference positioning where repeatable end‑measurements are required. It functions as a precise plug for validating bore sizes, setting up fixtures and serving as a datum in assembly checks. Because the design is straightforward, the pin integrates easily into existing gauge blocks, plug gauges and fixture components — aiding quick verification without elaborate setup. The clear specifications simplify selection for standardised inspection procedures and fixture design. Secure workshop precision with Metav IndustryLine's M323.450 gauge pin — contact Metav Werkzeuge in Emmerich for specification advice and integration guidance at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.450 SKU: M323.450 GTIN: 4061905057984 Brand: Metav IndustryLine Category: Measuring pins Facts Diameter: 4.50 mm Length: 50 mm Nominal measuring range: 4.50 mm Tolerance: ±0.001 mm Weight: 0.009 kg ECLASS: 21170231 Special features Workshop execution Material: Special steel Single unit Application: End measurements / reference positioning Story trigger: end‑measurements FAQ What accuracy does this gauge pin provide? The measuring pin M323.450 (Metav IndustryLine, gauge pin) is specified to ±0.001 mm, offering high repeatability for end‑measurements and reference checks. Which material is used for the pin? The pin is made of special steel, selected for wear resistance and dimensional stability in routine workshop use. How is the product supplied? This item is supplied as a single measuring pin, delivered for immediate use in inspection and jig applications. Can this pin be used in fixtures and plug gauges? Yes — the M323.450 is intended for integration into fixtures, plug gauges and reference assemblies where a stable 50 mm seating length and 4.50 mm diameter are required. What identifiers are available for ordering and traceability? Order and catalogue details: SKU M323.450, GTIN 4061905057984, brand Metav IndustryLine Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5mm Limit Plug Gauge Wear Allowance On Good Side, DIN 7162 - Filetta
Reliable DIN 7162 conformity and hardened steel construction give reproducible go/no-go checks; the built-in wear allowance on the good side extends service life. Take advantage of precise inspection, simple handling and long-term durability — order directly via Metav Werkzeuge or consult our specialists for tailored advice. Limit gauge pin MS911.207 — hardened steel, DIN 7162 (Ø 4.5 mm) The Limit gauge pin is a hardened-steel inspection pin designed for rapid go/no-go verification in workshop and production environments. Hardened steel construction, DIN 7162 compliant Diameter 4.5 mm for accurate limit checks Wear allowance on the good side to extend life Compact design for bench and fixture inspection Repeatable checks for fast quality decisions The limit gauge pin MS911.207 provides a straightforward method for pass/fail inspection that reduces decision time on the shop floor. Manufactured to DIN 7162, the pin’s hardened steel body maintains dimensional stability during repeated engagement, which supports consistent repeatability of go/no-go results. Using a simple plug-style verification avoids time-consuming measuring steps, improving throughput and lowering the cost of quality control across batches. Longer service life with controlled wear A decisive benefit of this inspection pin is the wear allowance on the good side, which compensates for material loss at the contact surface and preserves the calibrated function of the gauge for longer. The hardened finish resists surface damage while the allowance provides a controlled end-of-life margin, making maintenance planning predictable. This combination of durability and planned wear supports lower replacement frequency and steadier measurement confidence in production environments. Practical integration into standard inspection workflows Compact and purpose-built, the pin is suitable for quick checks in assembly, jig inspection and incoming goods control where clear go/no-go outcomes are required. The Ø 4.5 mm size fits small bores and fixture interfaces without complex setup, allowing inspectors to focus on throughput rather than instrument adjustment. The straightforward geometry and compliance with recognised standards make the pin an efficient addition to regulated inspection procedures and routine quality checks. Choose the Filetta limit gauge pin for DIN 7162-compliant checks and contact Metav Werkzeuge for fast delivery from Emmerich or expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.207 Name: Limit gauge pin Brand: Filetta Standard: DIN 7162 Key measurements Diameter: 4.5 mm Materials & special features Material: hardened steel Special feature: wear allowance on the good side Application: go/no-go inspection and limit checking FAQ What standard does this gauge pin follow? The Filetta limit gauge pin MS911.207 is manufactured to DIN 7162, ensuring conformity with widely recognised inspection practices. Which material is used for the pin and why does it matter? The pin is made from hardened steel, chosen for its resistance to wear and ability to retain dimensional stability under repeated use. How does the wear allowance affect inspection intervals? The wear allowance on the good side provides a predefined material margin, allowing predictable replacement scheduling and extending usable service life before a new gauge is required. For which inspection tasks is this pin intended? It is intended for rapid go/no-go verification of small bores and fixture interfaces, making it suitable for bench checks, assembly control and routine production inspections. Is the pin suitable for automated fixtures or only manual checks? Its compact, standard geometry allows use in manual inspection and integration into simple fixtures; suitability for automation depends on fixture design and handling requirements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4.5mm Limit Plug Gauge Wear Allowance, DIN 7162 - Filetta
The combination of robust hardened steel, conformity to DIN 7162 and a precise 4.5 mm nominal size ensures reliable pass/fail checks and long service life for small-bore inspection tasks; order the limit plug gauge directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. Limit plug gauge G7 – 4.5 mm, hardened steel by Filetta The Limit plug gauge G7 is a compact inspection pin designed for rapid go/no‑go acceptance testing of holes and bores in production and quality control settings. Hardened steel construction Conforms to DIN 7162 tolerance 4.5 mm nominal diameter Wear allowance on the go side Precision checks that speed up inspection A dedicated plug gauge built to DIN 7162 provides a straightforward, traceable method for go/no‑go assessment. The gauge’s 4.5 mm nominal size and G7 designation make it suitable for small-diameter bores where repeatable acceptance criteria are required. As a limit gauge, it converts geometric requirements into a tactile pass/fail verdict, reducing interpretation time during routine checks. The hardened construction maintains the calibrated profile over repeated use, supporting consistent process decisions and fewer downstream reworks. Robust design that reduces maintenance intervals Manufactured from hardened steel, the gauge resists premature wear in standard workshop environments, while the integrated wear allowance on the go side provides an engineered margin to extend useful life without compromising measurement integrity. This design choice lowers the frequency of replacements and conserves inspection resources, which translates into reduced process interruptions and predictable tooling budgets. The simple, single‑feature function of the instrument makes it a durable choice for shop‑floor verification and repetitive production control. Practical procurement and workshop integration The compact format and clear specification—listed under SKU MS911.165—enable easy stock management and fast identification in procurement systems. As a standardised acceptance tool, the plug gauge fits into established quality routines and can be used alongside other control artefacts to document conformity. Choosing a gauge from a recognised supplier supports traceability and aligns with systematic inspection plans; Metav’s distribution and inventory handling further simplify replenishment and selection for industrial and trade customers. Contact Metav Werkzeuge in Emmerich for availability and application advice on the Filetta limit plug gauge MS911.165 and to arrange delivery or technical consultation Technical data Article number: MS911.165 Material: hardened steel Nominal diameter: 4.5 mm Standard: DIN 7162 Facts Product type: limit plug gauge Designation: G7 Category: Gauges; Pin gauges Special features Wear allowance on the go side Compact inspection pin for small bores Suitable for routine go/no‑go acceptance testing FAQ What is the intended use of this limit plug gauge? The Filetta limit plug gauge MS911.165 is intended for quick go/no‑go checks of small bores to verify dimensional conformity to a specified tolerance class. How does the wear allowance affect service life? The built‑in wear allowance on the go side delays rejection due to normal surface wear, extending the practical lifetime of the gauge while maintaining reliable pass/fail decisions. Is the gauge suitable for use on finished components in production? Yes, the hardened‑steel construction and conformity to DIN 7162 make this limit plug gauge suitable for routine inspection of finished parts on the production line. Can this gauge be used for calibration or measurement recording? As a go/no‑go limit gauge, it serves as a conformity check rather than a measuring instrument for recorded dimensions; traceable gauge records should be maintained per internal quality procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4.5mm Setting Ring, Hardened Gauge Steel, Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the certified tolerances and robust, lapped surface finish for fast, reproducible size setting in production and inspection. The combination of hardened gauge steel, DIN conformity and compact form factor keeps set‑up times short and rejects down to a minimum. Order the setting ring directly via Metav Werkzeuge or consult the Metav team for application advice. Setting ring 4.5 mm (Form C) — hardened, lapped gauge steel by Metav IndustryLine The Setting ring 4.5 mm (Form C) is a hardened, lapped ring gauge for precise size setting and verification in workshop and inspection environments Hardened, lapped gauge steel Conforms to DIN 2250 and DIN 286 JS 3 Precise 4.5 mm diameter for accurate setting Improve setup accuracy with certified tolerances The Setting ring 4.5 mm (Form C) offers a compact reference for rapid tool and fixture alignment; its hardened and lapped gauge steel surface yields a stable seating and minimal wear, which supports consistent measurements over repeated use. Compliance with DIN 2250 and DIN 286 together with tolerance class JS 3 provides a known, reproducible fit that reduces setup deviation and contributes to higher first‑pass yield in machining and assembly operations. This makes the gauge suitable where repeatable dimensional references are required. Designed for durable, low‑maintenance throughput Constructed from hardened, precision‑finished gauge steel, the ring resists deformation and surface damage that would otherwise degrade accuracy. The lapped finish ensures low friction and predictable contact conditions during routine use, lowering the need for frequent replacement. Owing to its small footprint and modest mass, the ring is easy to handle and integrate into a standard inspection kit, while remaining sufficiently robust for daily workshop use. The result is a component that preserves measurement quality and reduces downstream rework. Fits directly into inspection and setting workflows As a purpose‑built setting device, the ring supports quick checks of tool sizes, gauge blocks and go/no‑go processes where a calibrated reference is required. Its compact diameter and Form C geometry suit small‑bore and internal seating checks, and the clear normative traceability simplifies documentation for quality records. When combined with routine verification procedures, the ring helps standardise setting practices across shifts and reduces operator variability, supporting tighter process control in both production and maintenance environments. For specialist guidance on integrating Metav IndustryLine setting rings into existing quality procedures, or for supply from our Emmerich stock, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M313.004.5 GTIN: 4054469120423 Label: Einstellring 4,5 mm, DIN 2250 aus gehärtetem Lehrenstahl; 0,01 kg Facts Diameter: 4.5 mm Weight: 0.1 kg eCl@ss: 21170104 Tariff number: 90173000 Special features Material: hardened and lapped gauge steel Form: Form C Standards: DIN 2250; DIN 286, JS 3 Category: gauges / setting rings FAQ What is the intended use of this setting ring? The setting ring is intended as a precision reference for size setting and verification in workshop and inspection contexts; the Setting ring 4.5 mm (Form C) from Metav IndustryLine (SKU M313.004.5) is suited to compact seating and small‑bore checks. What material and finish ensure the ring's longevity? This ring is made from hardened and lapped gauge steel, which provides wear resistance and a stable contacting surface for repeatable measurements. Which tolerances and standards apply to the gauge? The ring conforms to DIN 2250 and DIN 286 with tolerance class JS 3, ensuring a standardised fit and documented dimensional accuracy. Can the ring be used for internal and external setting tasks? Yes, the Form C geometry and the precise 4.5 mm diameter make the ring suitable for compact internal seating checks and as a reference for setting tools and gauges. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.61mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm dimensional control combined with a compact 4.61 mm diameter and a 50 mm usable length for reliable end‑dimension inspection; the workshop‑grade construction and delivery in a protective case support repeatable handling and safe transport. Order the gauging pin directly via Metav Werkzeuge or ask the consultants for further advice. Gauging pin M323.461 – 4.61 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauging pin M323.461 is a precision inspection pin designed for end‑dimension verification in production and quality control, ideal where tight tolerances and rapid, repeatable checks are required High precision ±0.001 mm tolerance Diameter 4.61 mm, length 50 mm Special steel construction for stability Delivered in protective transport case Assured accuracy for critical tolerances The compact inspection pin delivers a guaranteed ±0.001 mm tolerance, ensuring measurable repeatability when checking bores, shafts or end dimensions. Such fine accuracy reduces ambiguous go/no‑go decisions during first‑off inspections and in small‑batch production. By specifying a fixed diameter of 4.61 mm, the component supplies a clear, traceable reference that supports process capability studies and in‑line verification without the need for elaborate fixtures. Durable workshop design for consistent handling Built in a workshop design from special steel, the pin balances stiffness and handling comfort for routine use on the shop floor. The 50 mm length offers a practical working grip while keeping the measuring end stable; the low mass of approximately 0.009 kg minimises inertial effects in manual checks. The construction focuses on dimensional stability, so the gauge maintains its form under typical workshop conditions and frequent use, helping to lower the rate of measurement‑related rework. Practical storage and integration into inspection routines Delivery in a protective case simplifies transport between inspection stations and prevents accidental damage to the measuring face, supporting consistent readings day after day. The pin integrates easily into manual inspection rigs and simple gauge blocks, serving as a quick reference for end‑dimension checks and sample inspections. Traceability is supported by the clear article identification, enabling straightforward inventory management and replacement planning within established quality processes. For application advice or to confirm the M323.461 fits a specific inspection task, contact Metav Werkzeuge for a technical consultation and secure rapid delivery from Emmerich. Technical data Article number: M323.461 GTIN: 4061905059933 Manufacturer: Metav IndustryLine Category: Messstifte Label: Prüfstift, einzeln, 4,61mm, +/- 0.001 mm Länge 50 mm Weight: 0.009 kg Material: Special steel Measurements / Key specifications Diameter: 4.61 mm Length: 50 mm Tolerance: ±0.001 mm Measurement range (nominal): 4.61 mm Special features Workshop version Delivered in protective transport case Designed for end‑dimension inspection Compact, easy to handle FAQ What is the intended use of this gauging pin? The M323.461 gauging pin from Metav IndustryLine is intended for end‑dimension verification of bores and shafts where a fixed 4.61 mm reference and ±0.001 mm tolerance are required. Is the pin suitable for repeated shop‑floor use? Yes, the workshop design and special steel construction make the pin suitable for repeated manual checks and routine inspection tasks. Does the delivery include protective packaging? Delivery of the M323.461 includes a protective transport case to prevent damage and to keep the measuring face clean during storage and transit. Can this pin be used with gauge blocks or inspection fixtures? The pin is compatible with common gauge block setups and simple inspection fixtures used for end‑dimension checks and quick go/no‑go comparisons. How is repeatability ensured when using this pin manually? Repeatability is promoted by the pin's tight ±0.001 mm tolerance, compact form factor and a robust workshop design that limits deformation during handling. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.62mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of ultra‑tight tolerance and compact form for dependable end‑dimension checks; the precise diameter and robust material deliver consistent repeatability in workshop inspection. Order the gauge pin directly via Metav Werkzeuge or ask their consultants for tailored guidance. Gauge pin M323.462 — precision test pin, Ø 4.62 mm ±0.001 mm, length 50 mm (Metav IndustryLine) A gauge pin M323.462 engineered for high‑precision dimensional verification in inspection, assembly and tooling setups. Tolerance ±0.001 mm for ultra‑high precision Diameter 4.62 mm nominal Length 50 mm for deep seats and fixtures Made from special steel for wear resistance Reduce inspection time with measured confidence A compact, high‑accuracy test pin shortens the time spent on repetitive checks by eliminating uncertainty at the measurement stage. With a tolerance of ±0.001 mm, the pin functions as a definitive reference for end‑dimension inspections where interchangeability and fit are critical. This level of precision reduces downstream rework and accelerates go/no‑go decisions on the shop floor. The small footprint and smooth surface ensure rapid insertion into bores and seats, helping to maintain steady throughput in quality control routines. Durable construction that keeps accuracy over time Constructed from special steel, the pin resists surface wear and preserves its calibrated dimensions during prolonged handling. The 50 mm shaft provides sufficient length for use in deeper fixtures while remaining easy to manipulate by hand or with light clamping. Workshop‑grade finishing on the contact surfaces minimises risk of scoring and stabilises the contact conditions that determine measurement repeatability. Where frequent checks are required, the material choice and surface treatment together extend service life and sustain measurement confidence. Clear traceability and practical fit for production tasks As a single‑piece precision reference, the pin supports reproducible checks on mating parts and assembly features, improving process reliability. The nominal diameter 4.62 mm aligns with common end‑dimension standards and can be used as a control artefact during routine acceptance tests. Supplied as an individual test element, it integrates easily into inspection sets and can be combined with gauge blocks or fixture jigs for composite checks. For procurement and supply reliability, Metav IndustryLine provides a European distribution and quality gateway that simplifies sourcing for workshops and production sites. Specify the Metav IndustryLine M323.462 for critical end‑dimension checks and contact Metav Werkzeuge in Emmerich for purchasing and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.462 GTIN: 4061905059940 Manufacturer: Metav IndustryLine Numbers / Core technical data Nominal diameter: 4.62 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Special features / Versions Material: Special steel Delivery: single test pin (individual) Application focus: end‑dimension verification, inspection FAQ What is the dimensional tolerance of this test pin? The M323.462 gauge pin is manufactured to a tolerance of ±0.001 mm, allowing ultra‑tight dimensional verification. For which inspection tasks is this pin suited? It is intended for end‑dimension checks, fit‑up verification in fixtures and assembly control where a precise reference diameter of 4.62 mm is required. What material is used for the pin? The shaft is made from special steel, chosen for wear resistance and dimensional stability under normal workshop use. Can this pin be combined with other reference tools? Yes, the single‑piece design is compatible with gauge blocks, fixture jigs and other reference elements to build composite inspection set‑ups. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.63mm Gauge Pin ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of high positional accuracy and a robust workshop design to streamline inspection and end‑measurement tasks; the 4.63 mm diameter with ±0.001 mm tolerance and 50 mm overall length ensures repeatable fit checks and reliable go/no‑go comparisons. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for batch requirements and delivery options. Gauge pin M323.463 — 4.63 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A precision gauge pin designed for end‑measurements and fit verification in workshop and inspection environments. Workshop version for robust daily use Diameter 4.63 mm, tolerance ±0.001 mm Length 50 mm for end‑measurements Supplied in protective case for transport Ensuring measurement certainty where fit matters The 4.63 mm diameter pin with a tolerance of ±0.001 mm delivers the dimensional fidelity required for high‑precision fit and clearance checks. By specifying such a tight tolerance, the component reduces uncertainty in assembly verification and supports consistent pass/fail decisions during in‑process control. The clearly defined 50 mm length concentrates stiffness where end‑measurement is needed, improving repeatability compared with shorter or flexible pins. This technical consistency translates directly into fewer reworks and a more predictable inspection workflow. Designed for workshop handling and longevity Built as a workshop version, the pin is made from special steel chosen for wear resistance under frequent handling. The compact mass (approx. 0.009 kg) and balanced geometry simplify positioning during manual checks and reduce operator fatigue in repetitive tasks. Delivery in a protective case safeguards the measuring surface during transport and storage, preserving accuracy between uses. These characteristics make the item suitable for bench inspection, toolroom checks and integration into small‑batch production quality routines. Integrates with metrology processes and documentation The component supports traceable inspection steps by offering a defined nominal diameter and micro‑tolerance that can be recorded in inspection plans and measurement logs. With the supplied GTIN and clear SKU (M323.463), the pin is straightforward to reference in procurement, inventory and quality documentation. The specification favours applications such as end‑dimension verification, clearance testing and calibrated reference checks where a stable reference diameter is required to benchmark instruments or mating parts. Contact Metav Werkzeuge for delivery options, batch pricing and to discuss integration into your inspection routines — Metav Werkzeuge provides a dependable supply chain and specialist advice from Emmerich. Technical data Article number: M323.463 GTIN: 4061905059957 SKU: M323.463 Numbers / Core technical data Diameter: 4.63 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Design / Special features Workshop version Material: special steel Supplied in protective case Intended use: end‑measurements and fit checks FAQ What is the manufacturing tolerance of this gauge pin? The gauge pin is specified with a tolerance of ±0.001 mm, which defines its permitted deviation for precision fit and clearance testing. Which materials and environments is the pin suitable for? The pin is manufactured from special steel, offering good wear resistance for routine workshop and inspection use; specific corrosion resistance treatments are not indicated in the data. Is the pin supplied ready for transport and storage? Yes — the item is supplied in a protective case to protect the measuring surfaces during transport and handling. What typical tasks is this pin used for? Typical uses include end‑dimension verification, clearance and fit checks, and as a reference for manual inspection where a defined nominal diameter is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.64mm Gauge Pin ±0.001mm Length 50mm Workshop Version Special Steel in Case - Metav IndustryLine
High-precision ±0.001 mm tolerance, compact 50 mm length and specialised steel construction deliver reproducible reference measurements for inspection and assembly. Supplied in a secure transport case for workshop use. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.464 – single precision Ø 4.64 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.464 is a single precision reference pin designed for end‑measure checks and fit verification in metrology, inspection and assembly environments Ultra-fine ±0.001 mm tolerance Made from specialised steel Length 50 mm for deeper fits Supplied in transport case Precision that narrows uncertainty and stabilises inspections The ±0.001 mm specification corresponds to a 1 µm level of control, making this gauge pin suitable where minimal geometric deviation is critical. As a hardened reference element for plug fits and end‑measure checks, the component aids consistent repeatability in pass/fail testing and helps to reduce downstream rework. The accuracy rating supports traceable dimensional checks and provides a solid basis for comparative measurements on inspection benches and gauging jigs. Robust workshop design for handling and protection Constructed from specialised steel, the pin is produced to withstand regular workshop use while maintaining surface integrity and dimensional stability. The 50 mm length allows access into deeper bores or assemblies without compromising handling, and the compact weight supports fast positioning during batch checks. Supplied in a secure transport case, the item arrives protected against knocks and contamination, preserving calibration potential and reducing preparation time before use. Practical integration into quality processes and procurement As an individual precision reference, this pin fits into mechanical fixtures, plug gauge sets and custom test rigs where a defined reference diameter is required. The model M323.464 from Metav IndustryLine suits both inspection stations and production sampling routines, supporting faster decision cycles and reliable fit assessment. Combined with Metav’s warehouse and quality filter in Emmerich, the component contributes to accessible precision across workshops and small production sites. Contact Metav Werkzeuge in Emmerich for fitting advice or stock queries on the Metav IndustryLine gauge pin M323.464 Technical Data Article number: M323.464 GTIN: 4061905059964 Manufacturer: Metav IndustryLine Label: Gauge pin, single, 4.64 mm, ±0.001 mm, length 50 mm Facts Diameter: 4.64 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Special features Workshop version Supplied in transport case Material: Specialised steel Single precision gauge pin SKU: M323.464 FAQ What is the dimensional tolerance of this gauge pin? The M323.464 gauge pin offers a nominal tolerance of ±0.001 mm (1 µm), suitable for fine reference and fit‑checking tasks. What material is used for the pin? This precision element is made from specialised steel, selected for stability and wear resistance in workshop conditions. Is the pin suitable for deep‑seat measurements? The 50 mm length provides reach into deeper bores and assemblies while maintaining the stiffness required for repeatable checks. How is the item delivered for safe handling? The pin is supplied in a secure transport case to protect the finished surface and ensure safe storage during transport. Which product and brand does this item belong to? This is the Metav IndustryLine gauge pin, article number M323.464, intended as a single precision reference for inspection and assembly Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.65mm Test Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
The combination of workshop-grade robustness, a ±0.001 mm tolerance and a compact 4.65 mm diameter delivers reproducible end-dimension checks with minimal setup time; order the test pin directly via Metav Werkzeuge or consult the Metav team for application advice. Test pin M323.465 — Gauge pin, 4.65 mm diameter, ±0.001 mm (Metav IndustryLine) A Test pin M323.465 designed for precise end-dimension verification in workshop metrology, featuring a 4.65 mm ground diameter and a 50 mm hardened length High-precision tolerance ±0.001 mm Diameter 4.65 mm ground to gauge 50 mm hardened length for end-dimension checks Workshop version with transport box Repeatable precision for end-measurement tasks The gauge pin is manufactured to a tight ±0.001 mm tolerance, providing the repeatability required for reliable end-dimension control on small components. A ground 4.65 mm diameter ensures mating with gauge holes and fixtures without play, while the 50 mm length gives stable contact for end-face and through-hole checks. This level of accuracy suits inspection points where small deviations affect assembly quality; the hardened shaft and controlled geometry reduce wear and maintain measurement integrity over time. The result is fewer re-measurements and a more predictable quality flow. Compact design tailored to micro metrology Classified in the micro range, the pin matches the demands of very small measurement tasks where stiffness and minimal deflection are paramount. The compact dimensions and robust shaft avoid bending under typical workshop handling, enabling fast insertion into jigs, gauges or assembly checks. Constructed from special steel, the component is finished for reliable surface contact and long-term dimensional stability. The workshop execution balances precision with handling resilience, making it well suited for production inspection benches and toolroom applications. Integration, transport and practical handling Delivery in a transport box simplifies storage and protects the ground datum during handling and transit. The workshop-oriented specification facilitates quick use without additional modification: the ground diameter and hardened length are ready for direct application in end-measure checks and fixture-based inspection. Traceability is supported by the clear SKU and GTIN marking for inventory control, and the compact mass reduces inertia when used in automated or manual gauging setups, improving cycle times in routine quality control. For application-specific advice or ordering, contact Metav Werkzeuge to discuss how the Metav IndustryLine test pin can be integrated into existing inspection routines and gauging fixtures Technical data Article number: M323.465 GTIN: 4061905059971 Brand: Metav IndustryLine Diameter: 4.65 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.009 kg Material: Special steel Version: Workshop execution Packaging: Delivered in transport box Use case: End-dimension checks, gauge and fixture integration FAQ What level of accuracy does this gauge pin offer? The M323.465 gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high-precision end-dimension verification in workshop environments. Can the pin be used for through-hole gauging and end-face measurements? Yes, the 50 mm hardened length and ground diameter make the pin appropriate for both through-hole checks and end-face contact measurements. What material is the pin made from and how does that benefit its performance? The pin is produced from special steel, providing hardness and wear resistance that preserve dimensional stability and surface quality during repeated use. Is the product delivered ready for use and protected during transport? The workshop version is supplied in a transport box to protect the ground surface and facilitate safe storage and handling. How is the product identified for inventory and traceability? The test pin is supplied with the article number M323.465 and GTIN 4061905059971 for precise inventory control and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.66mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ultra-fine accuracy, robust workshop design and compact handling to keep inspection cycles short and rejection rates low; order the gauge pin directly via Metav Werkzeuge or contact our consultants for tailored advice. Gauge pin M323.466 – 4.66 mm, ±0.001 mm (50 mm length) by Metav IndustryLine The gauge pin M323.466 provides high-precision end-measurement capability for inspection benches and assembly jigs in workshop environments. Ultra-fine tolerance ±0.001 mm Diameter 4.66 mm for precise fits 50 mm length for stable handling Special steel for workshop durability Ensure reproducible decisions with submicrometre repeatability The gauge pin is designed for consistent measurement where a clear go/no-go distinction matters. With a stated accuracy of ±0.001 mm, the pin reduces ambiguity in fit checks and final inspections, which shortens decision loops on the shop floor. The tight tolerance is particularly valuable when assessing small-diameter bores or when validating end dimensions of turned components, enabling process engineers to rely on fast, objective results rather than prolonged sample analysis. The compact diameter and defined length help maintain a stable contact geometry during verification. Built for everyday workshop use without sacrificing precision Constructed from special steel, the pin combines surface hardness with dimensional stability to resist wear during repeated engagement. The workshop version balances resilience and handling comfort, so routine checks remain efficient across long production runs. A length of 50 mm provides sufficient reach for typical component depths while minimising the risk of deflection; the slender 4.66 mm profile supports use in small bores and precision fixtures. Overall, the material choice and shape reduce the need for frequent replacements and help preserve measurement integrity over time. Simple integration into inspection workflows The device’s compact geometry allows straightforward incorporation into measuring rigs, fixture checks or handheld gauges. As a hardened, single-piece inspection element, the pin is compatible with manual comparator setups and automated probing stations where a reliable reference diameter is required. Marked with SKU M323.466, it can be logged into quality control procedures and traceability lists, aiding auditability and quick identification during daily shift handovers. The low mass facilitates quick manoeuvring without compromising contact stability. Practical benefits for production and quality control Using this precision pin reduces scrap and rework by improving first-pass acceptance rates: rapid, reproducible checks prevent borderline parts from entering downstream assembly. The combination of fine accuracy and robust construction supports both corrective action and preventive process control, making it suitable for small-batch workshops and volume manufacturing alike. Confidence in measurement data leads to fewer process interruptions and a clearer allocation of operator time toward value-adding tasks. For procurement or technical clarification regarding the Metav IndustryLine gauge pin M323.466, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for expert assistance and reliable supply coordination Technical Data Article number: M323.466 GTIN: 4061905059988 Category: Messstifte Facts Diameter: 4.66 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.009 kg Special features Material: special steel Version: workshop execution Supplied individually Label: Prüfstift, einzeln FAQ What level of accuracy can be expected from this gauge pin? The gauge pin delivers an accuracy of ±0.001 mm, making the M323.466 suitable for high-precision go/no-go checks and tight-tolerance inspections. Which materials is the pin suitable for checking? The pin itself is made from special steel and is intended as a dimensional reference; it is used to verify the geometry of components made from metals and plastics where a precise bore or shaft diameter must be confirmed. Can the M323.466 be used in automated inspection fixtures? Yes, the M323.466 is suitable for integration into manual and automated fixtures where a defined reference diameter is required for repeatable measurement sequences. How is the gauge pin identified within quality documentation? Use SKU M323.466 and GTIN 4061905059988 for traceability and to reference the item in inspection protocols and inventory lists. Is this pin intended for general workshop use or laboratory calibration only? The pin is a workshop version, designed for routine inspection tasks on the shop floor while offering precision suitable for strict quality checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.67mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combine ±0.001 mm repeatability with a compact 4.67 mm diameter and a robust 50 mm shaft to secure reliable end‑measurements in the workshop. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin M323.467 — Precision 4.67 mm Ø, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.467 is a workshop‑grade single precision pin tailored for end‑measurements, reference checks and fit‑control tasks in production and quality inspection. Precision tolerance ±0.001 mm Diameter 4.67 mm for exact end‑measurements 50 mm hardened special steel shaft Workshop version for robust daily use Supplied in protective transport box Consistent high‑precision measuring for production control This precision pin offers an exceptional ±0.001 mm accuracy, providing stability for repeatable checks where micrometre‑level certainty matters. The compact 4.67 mm diameter and 50 mm length combine to deliver a low‑mass, rigid measuring probe that resists bending and thermal drift during short‑range checks. As a single‑item reference in the workshop, the pin supports fast go/no‑go verifications and serves as a reliable end‑stop for dimensional control, reducing rework and inspection time through consistent, comparable results. Durable construction for everyday workshop use Manufactured from special steel, the shaft is designed to withstand routine handling and the mechanical demands of industrial environments. The workshop execution indicates a focus on robustness and practical usability rather than fragile laboratory fittings, making this pin suitable for production floors and inspection benches alike. Delivered in a protective transport box, the item arrives ready for safe storage and mobility between workstations, preserving geometry and surface quality over repeated use. Practical benefits for QA and machining processes Using a dedicated precision pin simplifies final checks and assembly validation: the defined 4.67 mm diameter ensures predictable mating with bores and gauges, while the tight tolerance minimises measurement uncertainty during fit assessments. In short inspection cycles, the pin functions as a fast-reference master that speeds decisions and supports traceable quality routines. For workshops aiming to tighten tolerance control without complex fixtures, this precision pin offers a pragmatic and measurable improvement in process reliability. Contact Metav Werkzeuge for specification support or to order the Metav IndustryLine gauge pin M323.467 and arrange secure delivery from our Emmerich facility. Technical data Article number: M323.467 GTIN: 4061905059995 Label: Gauge pin, single, 4.67 mm, ±0.001 mm, length 50 mm Core specifications Diameter: 4.67 mm Accuracy: ±0.001 mm Length: 50 mm Weight: 0.009 kg eClass: 21170231 Features & materials Material: Special steel Version: Workshop execution Supplied in protective transport box Category: Gauge pins (Messstifte) FAQ What applications is this gauge pin intended for? The gauge pin M323.467 is intended for end‑measurements, fit‑control and quick reference checks in workshop and production quality inspection. Is the M323.467 suitable for repeated use on the shop floor? Yes, the Metav IndustryLine gauge pin is a workshop version made from special steel and supplied in a protective transport box for repeated handling and secure storage. How precise is the diameter and what tolerance can be expected? The pin has a diameter of 4.67 mm with an accuracy of ±0.001 mm, making it suitable for high‑precision fit and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.68mm Gauge Pin, ±0.001 mm, Length 50 mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
A precision gauge pin designed for reliable fit checks: the tight ±0.001 mm tolerance combined with a 4.68 mm diameter and 50 mm length delivers consistent, repeatable results in workshop metrology. Supplied in a transport case and made from special steel, this workshop‑grade inspection pin supports efficient production control. Order directly via Metav Werkzeuge or consult our advisors for application guidance. M323.468 Gauge Pin — 4.68 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) The M323.468 is a workshop‑grade gauge pin for end‑measure and fit verification tasks, suitable for precision inspection and assembly control in machine shops and fixture manufacture. Precision ground 4.68 mm diameter Tolerance ±0.001 mm Length 50 mm for deep fit checks Workshop‑grade construction in special steel Repeatable precision for production control The core advantage of this inspection pin is its high repeatability thanks to a fine tolerance of ±0.001 mm, which reduces measurement uncertainty when checking bores, fits or mating parts. For process engineers and quality technicians this means fewer rejects and faster go/no‑go decisions; a single, stable reference dimension simplifies statistical process control and shortens inspection cycles. The precision ground surface supports consistent contact and minimal surface deformation during checks. Robust workshop design that endures everyday use Built as a workshop‑grade tool from special steel, the pin combines wear resistance with dimensional stability for repetitive use on the shop floor. The 50 mm overall length provides access to deeper seats while maintaining stiffness in the shaft, helping to avoid bending that can compromise results. Supplied in a transport case, the pin is protected in storage and transit, preserving the ground finish for prolonged service life. Practical handling and application benefits The compact, cylindrical geometry enables quick insertion into bores and accurate control of end‑measure checks. For applications such as gauge setting, fixture alignment and component inspection, the pin behaves as a straightforward, low‑complexity reference standard. Its 4.68 mm diameter is suitable for fine fit assessments and offers compatibility with gauges and fixtures used in precision assembly and small‑component manufacture. Integration into quality workflows As a simple, robust reference tool, the pin supports rapid inspection routines and can be included in first‑piece checks, incoming goods inspection and in‑process verification. Traceability is aided by the clear identification data provided with the item, facilitating documentation in quality reports and inspection logs. The combination of durability and tight tolerance makes it a pragmatic choice where dependable dimensional validation is required without complex instrumentation. Contact Metav Werkzeuge for precise supply and application advice on the Metav IndustryLine gauge pin and to arrange shipment from our Emmerich facility. Technical data SKU: M323.468 GTIN: 4061905060793 Brand: Metav IndustryLine Article designation: Gauge pin, single Facts Diameter: 4.68 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Material: Special steel Special features Workshop execution Transport case included for protection Precision ground surface Intended for end‑measure and fit checks FAQ What tolerance does this gauge pin have? The M323.468 gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision fit and bore checks. Which material is the pin made from? The inspection pin is made from special steel, chosen for wear resistance and dimensional stability in workshop conditions. Is the pin supplied ready for storage and transport? Yes, the pin is supplied in a transport case to protect the precision ground surface during handling and storage. For what applications is this gauge pin intended? The pin is intended for end‑measure and fit verification in machine shops, fixture construction and quality inspection routines. How is the product identified for traceability? The item is listed as M323.468 (Metav IndustryLine) and carries the GTIN 4061905060793 for documentation and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.69mm Gauge Pin ±0.001mm Length 50mm Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of high metrological accuracy and robust workshop design: the combination of ±0.001 mm tolerance and a 4.69 mm nominal diameter in a compact 50 mm pin supports repeatable end‑measurement and tight‑fit checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists if technical advice is required. M323.469 Gauge Pin – 4.69 mm Ø, ±0.001 mm accuracy (Metav IndustryLine) The M323.469 is a precision gauge pin intended for end‑measurement and assembly checks in workshop metrology, offering a compact 50 mm length for confined inspection tasks Precision tolerance ±0.001 mm Diameter 4.69 mm for tight fits Length 50 mm for compact checks Special steel construction for durability Delivered in protective case for transport Accuracy that lowers rejection rates Manufactured to a tolerance of ±0.001 mm, this gauge pin enables highly repeatable measurements that reduce inspection uncertainty and rework. The narrow diameter of 4.69 mm makes it suitable for verification of press fits, hole gauges and assembly bores where tight clearances matter. By providing a defined reference dimension, the pin simplifies go/no‑go checks and supports statistical quality processes in small‑batch production and workshop QC routines. Robust workshop design for consistent performance Designed as a workshop version, the test pin is made from special steel to resist wear and preserve dimensional stability during frequent handling. The compact 50 mm length balances stiffness and accessibility, keeping deformation negligible while probing confined features. Supplied in a protective case, the pin stays shielded during storage and transport, which helps to maintain calibration intervals and avoids unnecessary downtime for replacements. Practical handling and integration into inspection workflows The small mass and compact form factor make the pin easy to position in fixtures or jigging setups; its geometry supports common end‑measurement tasks without complex adapters. As a dedicated inspection tool for end measurements and tight‑fit verifications, the pin integrates smoothly into existing gauge sets and bench routines, raising throughput by shortening individual checking steps while maintaining traceable reference values. For workshop-ready precision from Metav IndustryLine, request the M323.469 gauge pin via Metav Werkzeuge — technical advice and dispatch from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data SKU: M323.469 GTIN: 4061905060809 Category: Gauge pin (test pin) Facts Diameter: 4.69 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Special features Workshop version Special steel construction Delivered in protective case Intended for end‑measurement and tight‑fit checks FAQ What tolerance is achieved with this gauge pin? The M323.469 is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision end measurements and tight‑fit verification. Which material is the pin made from? The pin is produced from special steel, chosen for wear resistance and dimensional stability in workshop environments. Is the pin supplied ready for transport and storage? Yes — the gauge pin is delivered in a protective case to prevent damage during transport and to maintain measurement integrity. For which inspection tasks is this pin best suited? This gauge pin is intended for end‑measurement, assembly checks and tight‑fit inspections where a precise reference diameter is required. What are the SKU and GTIN for ordering and traceability? SKU: M323.469 GTIN: 4061905060809 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.6mm Gauge Pin Single ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of uncompromising precision, compact workshop design, and robust special steel construction for repeatable end‑measurement checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.460 – Precision gauge pin, 4.60 mm ±0.001 mm (Metav IndustryLine) The Gauge pin M323.460 is a single precision pin for end‑measurements and inspection tasks in workshop environments, offering a tight ±0.001 mm tolerance and a 50 mm working length. Workshop version, durable construction Diameter 4.60 mm with ±0.001 mm accuracy Length 50 mm for depth and end‑measure checks Supplied in a protective case Repeatable accuracy for routine inspection The M323.460 is engineered for repeatable end measurements, delivering a ±0.001 mm tolerance that reduces rework and speeds up quality checks. Manufactured from special steel, the pin maintains form and surface integrity under regular use, which supports consistent results when comparing parts to end‑measure references. The compact design and precise diameter make it straightforward to include this pin in inspection jigs or handheld checking routines, improving throughput in small‑batch and series production alike. Robust workshop design that eases handling Designed as a workshop version, the pin combines resilience with practical handling characteristics. The 50 mm overall length provides sufficient reach for many depth and end‑face checks while remaining easy to manoeuvre in confined setups. Supplied in a protective case, transport and storage are simplified and the pin arrives ready for immediate use on the shop floor. The nominal mass of 0.009 kg supports quick positioning and limits operator fatigue during repetitive checks. Clear specification and practical integration Key specifications such as 4.60 mm diameter and ±0.001 mm tolerance are stated for direct use in inspection plans and documentation; the item is listed under SKU M323.460 for traceable ordering. The special steel construction ensures dimensional stability and resistance to routine wear, making the pin suitable for tactile and optical comparison tasks. For organisable workflows, the compact single‑pin format is compatible with existing gauge blocks, holder fixtures and manual measuring stations, enabling straightforward integration without the need for bespoke tooling. Contact Metav Werkzeuge today to request detailed delivery options for the M323.460 precision gauge pin or to discuss application‑specific advice from our consultants Technical data Article number: M323.460 GTIN: 4061905058974 Manufacturer: Metav IndustryLine Facts Diameter: 4.60 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Special features Material: special steel Workshop version construction Supplied in protective case for transport Single gauge pin for end‑measure checks FAQ What is the exact diameter and tolerance of this pin? The M323.460 gauge pin has a diameter of 4.60 mm and a tolerance of ±0.001 mm, suitable for tight inspection tasks. What is the pin made from? The pin is manufactured from special steel, offering dimensional stability and resistance to routine workshop wear. What length does the pin have and how is it used? The pin is 50 mm long and is intended for end‑measure and depth checks, either handheld or mounted in inspection fixtures. How is the pin delivered? The gauge pin is supplied in a protective case to ensure safe transport and storage. Which SKU should be ordered for this product? Order using SKU M323.460 (Metav IndustryLine) to ensure the correct precision gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.71mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
High-precision end measurement is ensured by the combination of a tight ±0.001 mm tolerance, a true 4.71 mm diameter and a rigid 50 mm length; the workshop-grade construction in special steel delivers repeatable checks and long service life. Order the gauge pin directly via Metav Werkzeuge or consult the team for technical clarification. Gauge pin M323.471 (Metav IndustryLine) — 4.71 mm, ±0.001 mm A gauge pin designed for precise end measurements in inspection and workshop use, supplied as a single, 50 mm long probe for tight-fitting checks. Single-piece gauge pin 4.71 mm diameter Tolerance ±0.001 mm for tight fits Length 50 mm for end-measurements Workshop-grade special steel construction Reliable tight-tolerance checks for critical fits This workshop-grade pin provides a consistent reference for end measurements where fit and clearance matter. The ±0.001 mm tolerance reduces uncertainty during assembly checks and quality control, meaning fewer rework cycles and clearer go/no-go decisions. Hardened and finished from special steel, the pin maintains edge integrity during repeated insertion into bores or jigs, preserving both component integrity and inspection accuracy. Practical advantage on the shop floor The compact, single-piece design makes the pin straightforward to handle during batch inspection and setup tasks. With a 4.71 mm diameter and 50 mm length, the probe is well suited to verify bores, dowel seats and end masses where precise axial positioning counts. The robust material choice supports daily use in demanding environments, while the geometry limits flex and wobble to aid repeatable readings on manual and semi-automatic fixtures. Integration into quality routines and tooling sets As a precision reference component, this gauge pin fits into common inspection routines and can be paired with gauge blocks, go/no-go fixtures or measurement benches. The clear numeric specification (diameter, length, tolerance) simplifies documentation and traceability within production records and inspection plans. Specifying the M323.471 in procurement or tooling lists ensures consistent performance expectations across shifts and suppliers. For technical advice, availability and suitability of the Metav IndustryLine M323.471 gauge pin, contact Metav Werkzeuge in Emmerich by e‑mail or phone for fast, experienced support Technical data SKU: M323.471 GTIN: 4061905060823 Material: Special steel Type: Single-piece gauge pin Version: Workshop execution Label: Gauge pin, single, 4.71 mm, ±0.001 mm, length 50 mm Numerical data Diameter: 4.71 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.009 kg Special features Workshop-grade finish End-measurement application Single item supply Suitable for recurring dimensional checks FAQ What is the exact tolerance of this gauge pin? The gauge pin is specified with a tolerance of ±0.001 mm, enabling high-precision verification of fits and bores. Which material is used for the pin? The M323.471 is manufactured from special steel, chosen to combine dimensional stability with wear resistance for workshop environments. For which applications is this pin intended? Typical uses include end measurements, bore checks, dowel seat verification and use as a reference in fixtures where precise diameters and axial positions are required. What is the ordering code for this item? The SKU for ordering is M323.471. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.72mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the proven combination of extreme measuring accuracy and robust construction for reliable fixture setting and end‑dimension gauging; the precise ±0.001 mm tolerance together with the special steel body ensures repeatable results and long service life — order the test pin directly via Metav Werkzeuge or consult the specialists for application advice. M323.472 Test pin — Precision gage pin 4.72 mm, ±0.001 mm (Metav IndustryLine) M323.472 Test pin is a single high‑precision gage pin for end measurements, fixture setting and reference positioning in workshop and production environments High-precision tolerance ±0.001 mm Special-steel construction 50 mm length for stable positioning Workshop version for everyday use Measured accuracy that reduces rework and inspection uncertainty The core benefit of this gage pin is its ±0.001 mm nominal tolerance, which corresponds to a sub‑micrometre class fit for precise alignment and end‑dimension checks. Such a tight specification lowers uncertainty in assembly and inspection operations, so fewer parts require rework. The small nominal diameter of 4.72 mm provides a sharply defined contact point for pinpoint positioning; repeatability is improved because the geometry minimises play in jigs and locators. This level of precision supports rational production decisions, speeding up set‑up times and stabilising quality control metrics. Workshop‑ready materials and handling for daily use Manufactured from special steel, the test pin resists wear under repeated seating and unclamping cycles while maintaining the contact geometry essential for reproducible measurements. The 50 mm overall length balances reach and stiffness, reducing bend and ensuring a secure reference in simple fixtures and portable gauges. Supplied as a single‑piece test pin in a workshop design, it is intended for frequent handling and rapid use on shop floors where robustness and low maintenance are priorities. The material choice and heat treatment result in stable dimensional behaviour during normal production use. Simple integration into inspection and fixture workflows Designed as a benchmark component, the M323.472 integrates easily into gauge assemblies and fixture plates where defined end measurements are required. The pin is suitable for use as a reference for go/no‑go checks, alignment dowelling and for establishing datum points during assembly. By using a standardised, precision pin from the Metav IndustryLine, process engineers gain a predictable reference part that simplifies inspection procedures and reduces the need for repeated adjustments. Traceable identifiers such as the SKU and GTIN support inventory and quality documentation. For workshop-ready precision, order the Metav IndustryLine M323.472 from Metav Werkzeuge in Emmerich — the team there provides purchase guidance and practical delivery options tailored to production needs. Technical data Article number: M323.472 GTIN: 4061905060830 Brand: Metav IndustryLine Facts Diameter: 4.72 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.009 kg Material: Special steel Special features Workshop version Single test pin for end measurements Application: reference positioning and fixture setting Eclass: 21170231 FAQ What level of accuracy can be expected from this gage pin? The M323.472 test pin is specified at ±0.001 mm, offering sub‑micrometre class accuracy suitable for tight alignment and end‑dimension checks. Is the pin suitable for repeated use in jigs and fixtures? Yes, the special‑steel construction and workshop design make the M323.472 well suited for repeated seating and regular use in fixture and gauge assemblies. Can this pin be used as a datum or reference in assembly operations? The M323.472 is intended for reference positioning and can serve as a datum pin in go/no‑go checks and alignment procedures within production workflows. Which applications benefit most from a 4.72 mm diameter pin? Small‑bore alignment, precision dowelling and end‑measurement tasks typically benefit from the defined contact of a 4.72 mm pin, especially where repeatable positioning is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com