Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
6.08mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Special Steel, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm tolerance and a 50 mm working length for highly reproducible end‑measure checks; the compact design made from special steel and the workshop‑grade finish ensure durable daily use, with delivery in a robust transport case. Order the inspection pin directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin M323.608 — 6.08 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.608 gauge pin — a workshop‑grade inspection pin designed for precise end‑measure verification and set‑up tasks in metrology and production control. Workshop‑grade precision component Diameter 6.08 mm ±0.001 mm Length 50 mm for end‑measure checks Supplied in a transport case Precision that secures repeatable end‑measure checks The inspection pin is manufactured for high repeatability in end‑dimension tasks, offering a declared tolerance of ±0.001 mm (1 µm). Such fine accuracy reduces measurement uncertainty when used for go/no‑go verification, plug‑gauging or as a reference mandrel in fixture set‑up. The small diameter and short working length make the item especially suited to tight‑tolerance checks where minimal form error and consistent contact geometry are required. This performance supports faster in‑process decisions and tighter quality control limits. Robust material and workshop design for daily handling Constructed from special steel, the component resists wear under regular use in workshop environments while preserving its calibrated profile. The workshop‑grade finish balances corrosion resistance and dimensional stability, so the gauge retains its form after repeated insertions and cleanings. The design is intended for straightforward handling and long service life, making it a practical choice where inspection frequency and throughput are high. Practical traceability and fit for inspection routines The pin is supplied in a protective transport case to maintain condition between uses and during storage or transport. With a compact footprint and low mass (approx. 0.014 kg), it integrates easily into existing inspection kits and fixture systems. The clear, graded tolerance specification and manufacturer identity facilitate traceability in quality documentation and help maintain consistent sampling routines on the shop floor. Typical applications and integration into quality workflows Ideal for end‑measure verification, plug‑gauging, and assembly jigs, this inspection pin performs well in machine shops, toolrooms and metrology benches where fine diameters must be confirmed rapidly. The component can be used as a reference for setting bore gauges or aligning mating parts during assembly. Its workshop configuration makes it particularly suitable for repetitive production checks where robustness and repeatability are priorities. Contact Metav Werkzeuge in Emmerich for procurement and technical guidance — Metav provides local stock, expert advice and pragmatic delivery solutions for precision metrology tools Technical data SKU: M323.608 GTIN: 4061905059537 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 6.08 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Materials / Special features Material: special steel Workshop execution Supplied in a transport case FAQ What degree of accuracy does this inspection pin offer? The M323.608 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometre‑level accuracy suitable for fine end‑measure checks and precision verification tasks. Is the gauge pin suitable for frequent workshop use? Yes. The workshop‑grade finish and special steel construction of the M323.608 make it suitable for regular handling in industrial inspection routines. Can this pin be used as a reference for bore alignment and jigs? The component is intended for end‑measure verification and is commonly used as a reference mandrel for setting bores and aligning assembly fixtures in production environments. Does the product include protection for transport and storage? The inspection pin is supplied in a robust transport case to protect the measuring surface and maintain condition between uses. Which documentation accompanies the pin for quality records? Product identification (SKU and GTIN) and the declared tolerance are provided; Metav IndustryLine supplies items with the manufacturer details needed for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.09mm Gauge Pin 50mm Length ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance (±0.001 mm), a compact 6.09 mm diameter and a 50 mm special‑steel length for reliable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.609 — single precision test pin, 6.09 mm diameter, ±0.001 mm tolerance (50 mm length) by Metav IndustryLine The Gauge pin M323.609 is a single precision gauge pin designed for workshop use and end‑measurement control, offering a fine 6.09 mm diameter with a laboratory‑grade ±0.001 mm tolerance in a 50 mm length. Single precision gauge pin 6.09 mm ±0.001 mm 50 mm special steel construction Workshop version for rugged handling Measurement‑grade tolerance for repeatable checks Exceptional metrology accuracy for tight fits This test pin delivers submicrometre repeatability with a declared tolerance of ±0.001 mm (1 micrometre), which is critical when verifying bore sizes, dowel fits or precision assemblies. The very small diameter and fine tolerance reduce measurement uncertainty when used as an end‑mass reference or in pin‑gage stacks. Such accuracy shortens inspection cycles: fewer adjustments are required during assembly and QC, because the measurement result can be relied on for pass/fail decisions. Robust design optimised for workshop environments Manufactured from special steel and specified at 50 mm overall length, the component is a single, solid test pin intended for regular use in production areas. The workshop specification focuses on handling resilience and dimensional stability under typical shop conditions. The compact form factor keeps manipulation straightforward while the material choice balances wear resistance with dimensional integrity, reducing the need for frequent replacement and helping to maintain consistent process capability. Practical integration into quality workflows The component is supplied as a single test pin and integrates easily into existing gauges, fixtures and pin jigs used in final inspection or incoming‑goods control. By using a dedicated measurement‑grade pin for go/no‑go verifications and feature checks, throughput is improved and measurement variability is reduced. The result is a more efficient inspection routine that supports traceable production decisions and stable assembly tolerances across batches. Contact Metav Werkzeuge today for tailored advice on integrating Metav IndustryLine gauge pins into quality control processes or to place an order — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.609 GTIN: 4061905060380 eClass: 21170231 Category: Messstifte Facts Diameter: 6.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.014 kg Special features Material: Special steel Version: Workshop execution Form: Single test pin Intended use: End‑measurement / pin‑gage applications FAQ What tolerance does this gauge pin offer? The gauge pin M323.609 is manufactured to a tolerance of ±0.001 mm (1 micrometre), making it suitable for high‑precision fit checks. Which material is used for the test pin? This Metav IndustryLine test pin is made from special steel, chosen for dimensional stability and wear resistance in workshop use. Is the pin suitable for use in pin‑gage fixtures and jigs? Yes; the 6.09 mm diameter and 50 mm length are compatible with standard pin‑gage holders and fixture bores for end‑measurement tasks. Can this item be used for checking dowel or bore fits? The gauge pin M323.609 is designed specifically for fit verification and end‑measurement of small bores and dowel seats where a 6.09 mm reference is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.0mm Limit Go Gauge H7, Hardened Gauge Steel DIN 2245 - Metav IndustryLine
Take advantage of the combination of DIN 2245 H7 accuracy, hardened gauge steel construction and compact 6.0 mm size for reliable, fast go/no-go bore checks; order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge M314.006 — 6.0 mm H7 (DIN 2245) by Metav IndustryLine The Limit plug gauge 6.0 mm H7 is a hardened cylindrical gauge intended for rapid go/no-go verification of bore diameters to DIN 2245, suited to shop‑floor inspection and production control. Hardened gauge steel construction DIN 2245, tolerance H7 Quick go/no-go bore checking Compact 6.0 mm diameter size Fast verification for routine production control Designed for repeatable pass/fail checks, this plug gauge delivers consistent results where cycle time and traceability matter. The combination of a DIN 2245 finish and H7 tolerance ensures that each check provides a clear, binary outcome that removes guesswork from inspection routines. The hardened construction maintains contact geometry under frequent use, reducing maintenance intervals and supporting uninterrupted production flows. This makes the gauge a practical choice for bench inspection, assembly lines and first‑off checks where speed and repeatability are priorities. Durable materials and straightforward handling Manufactured from hardened gauge steel, the gauge is prepared for continuous contact with finished bores while retaining the required measuring geometry. The solid cylindrical form and ground surface make handling intuitive: insert the pin into the bore and interpret the result immediately with a go/no-go criterion. The compact 6.0 mm diameter is particularly useful for small to medium bores and is compatible with common inspection jigs and fixtures. The material choice and finishing reduce the risk of wear‑induced measurement drift, thereby supporting reliable quality control without complex setup. Practical fit into metrology workflows The gauge integrates smoothly into standard inspection processes and documentation. Its simple pass/fail function speeds operator decisions and reduces training time, while the adherence to DIN 2245 provides a recognised reference for audits and supplier control. For traceability, the product is listed as SKU M314.006, enabling clear part specification in procurement and quality records. Where rapid sampling is required, this limit pin offers a pragmatic balance between precision and operational convenience, making it suitable for both production inspection and incoming part checks. For standardised, robust bore verification choose the Metav IndustryLine limit plug gauge and contact Metav Werkzeuge in Emmerich for procurement and technical guidance Technical data SKU: M314.006 GTIN: 4054469121352 Standard: DIN 2245 Data Diameter: 6.0 mm Customs tariff number: 90173000 eClass: 21170218 Special features Material: Hardened gauge steel Tolerance: H7 Product type: Limit plug gauge / plug gauge Category: Gauges FAQ What tolerance class does this plug gauge conform to? The limit plug gauge conforms to tolerance H7 according to DIN 2245, providing a clear reference for bore acceptance criteria. Is the gauge suitable for rapid go/no-go checks on the shop floor? Yes, the plug gauge is optimised for fast go/no-go bore verification in production and inspection environments, offering immediate binary results. What material is the gauge made from? The gauge is manufactured from hardened gauge steel, chosen to preserve measuring geometry under repeated use. How is the product identified for procurement and documentation? The item is listed under SKU M314.006 and GTIN 4054469121352 for unambiguous specification in orders and quality records. Can this gauge be used for audit and traceability purposes? Yes, adherence to DIN 2245 and a clear SKU/GTIN designation support use in documented quality systems and supplier audits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.11mm Test Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
High-precision reference for end measurements: a gauge pin with a nominal diameter of 6.11 mm, repeatable tolerance of ±0.001 mm and a 50 mm length; workshop-grade construction in special steel, supplied in a protective transport box. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.611 — single gauge pin, 6.11 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.611 is a workshop‑grade, single reference pin designed for precise end‑measurements and verification tasks in production and inspection environments. High repeatability ±0.001 mm Workshop version in special steel Compact 50 mm length for tight fixtures Supplied in protective transport box Precision where repeatability matters A nominal diameter of 6.11 mm combined with a tolerance of ±0.001 mm provides a dependable reference for go/no‑go checks and comparative measurements. The extremely small tolerance reduces measurement uncertainty and supports consistent decision making during quality checks. The special steel construction keeps dimensional stability under routine handling, while the compact form factor makes the pin suitable for confined gauges and fixtures. This paragraph emphasises the operational benefit: faster inspection cycles with fewer ambiguous results, improving throughput without sacrificing traceability. Built for workshop conditions and practical handling Designed as a workshop version, the pin balances robustness with fine accuracy. At 50 mm overall length and a mass of 0.015 kg, the item is easy to position in tight assemblies and remains stable during contact measurements. The construction is aimed at routine use rather than delicate laboratory environments, so durability in daily production settings is a clear advantage. The delivery in a protective box reduces the risk of transport damage and helps preserve the reference geometry between uses. Use cases and compatibility with inspection workflows This single gauge pin is intended for end‑measurement tasks, calibration jigs, fixture setting and component verification. Its ±0.001 mm tolerance makes it suitable where high repeatability is required—such as batch acceptance testing or final inspection of turned and ground parts. The compact diameter and short length enable integration into small fixtures and modular inspection plates. Where traceability is needed, the pin’s defined geometry supports clear go/no‑go decisions and reliable position references within assembly processes. Handling, maintenance and storage to retain accuracy To maintain the pin’s performance, handle with clean, dry hands or gloves and avoid impacts. Store the item in its protective box between uses to prevent nicks and surface damage that would affect accuracy. Routine checks with a calibrated micrometre or a comparator are recommended if the pin is exposed to heavy handling; any visible wear or deformation should prompt replacement to avoid measurement drift. These simple measures preserve the pin’s benefits: consistent measurements, fewer rework loops and trustworthy inspection outcomes. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for ordering and technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.611 GTIN: 4061905060403 Category: Messstifte Label: Gauge pin, single, 6.11 mm, ±0.001 mm, length 50 mm Facts Nominal diameter: 6.11 mm Length: 50 mm Tolerance / repeatability: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop version Delivered in protective transport box Intended for end‑measurements and fixture checks FAQ What tolerance does the gauge pin offer? The gauge pin M323.611 is specified with a repeatability of ±0.001 mm, making it suitable for high‑precision verification tasks. Is the pin suitable for fixture setting and end‑measurements? Yes, the M323.611 single gauge pin is intended for end‑measurements, fixture setting and go/no‑go checks in workshop inspection workflows. Does the product come with a calibration certificate? The product data does not indicate an ISO 17025 certificate for this item; please contact Metav Werkzeuge if an accredited calibration certificate is required. How should the gauge pin be stored to keep accuracy? Store the gauge pin in the supplied protective box, handle it with gloves, and avoid impacts; periodic checks with a calibrated micrometre are recommended to confirm continued dimensional accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.12mm Gauge Pin Single ±0.001mm Accuracy Length 50mm Workshop Version - Metav IndustryLine
The combination of submicron accuracy, compact dimensions and a robust workshop finish makes this gauge pin ideal for reliable end measurements; benefit from consistent fits and reduced rework. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. M323.612 Gauge Pin — 6.12 mm, ±0.001 mm (Workshop Version) by Metav IndustryLine M323.612 is a single gauge pin designed as a precise end-measurement master for workshop and inspection tasks Submicron tolerance ±0.001 mm Diameter accurately ground to 6.12 mm 50 mm length for stable seating and reference Workshop version with durable finish Reduce rejects with repeatable submicron precision The gauge pin is manufactured to a tolerance of ±0.001 mm, delivering repeatable results when used as an end-measurement master or reference pin. This level of precision minimises fit variation across production batches, cutting down on rework and inspection time. The 6.12 mm diameter is ground to size and held over the full length to ensure consistent contact geometry; the small mass also helps to avoid undue influence on delicate fixtures. Engineers and quality technicians benefit from faster decision-making thanks to fewer out-of-tolerance readings and clearer go/no-go outcomes. Built for stable seating and handling in workshop environments With a 50 mm overall length and a workshop-focused design, the pin provides a secure seating depth for probes, fixtures and assembly checks. The compact form reduces the risk of bending or deflection during handling while offering enough engagement to act as a reliable datum in jigs and checks. Made from special steel, the pin balances hardness and toughness to withstand regular use without rapid wear. The robust finish and straightness keep contact conditions consistent, which is crucial when measurements are used to validate mating parts or final assembly tolerances. Practical integration into inspection and production workflows The gauge pin is simple to incorporate into existing inspection routines: it serves as an end gauge, a locating pin for dimensional checks and a reference for comparative measurement setups. Traceability is supported by the clear SKU marking, and the compact weight (approx. 0.015 kg) makes handling straightforward during bench checks or when fitted into modular fixtures. For small-batch manufacturing and precision assembly, the pin reduces set-up variability and streamlines routine checks, providing measurable time savings in quality control cycles. For application-specific advice and to acquire the M323.612 gauge pin from Metav IndustryLine, contact Metav Werkzeuge for precise ordering and consultancy at info@metav-werkzeuge.com or by phone; Metav’s specialists will assist with selection and integration into existing measurement processes. Technical data SKU: M323.612 GTIN: 4061905060410 Product: Gauge pin, single, 6.12 mm, ±0.001 mm, length 50 mm Category: Gauge pins Manufacturer: Metav IndustryLine Facts Diameter: 6.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Measurement range min: 6.12 mm Measurement range max: 6.12 mm Special features Material: special steel Workshop execution Intended use: end measurements / reference pin Label: Prüfstift, einzeln (translated) FAQ What level of precision does this gauge pin offer? The M323.612 gauge pin is manufactured to a precision of ±0.001 mm, providing submicron-level repeatability suitable for tight-fit and end-measurement applications. Can the pin be used as a reference in fixture set-ups? Yes, the M323.612 gauge pin is intended for use as an end-measurement master and locating reference in jigs, fixtures and inspection routines. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen for a balance of hardness and toughness to resist wear under regular workshop handling while maintaining contact geometry. Is the diameter held over the full length? The diameter of 6.12 mm is ground and controlled for consistent contact; the 50 mm length ensures stable seating for measurement and fixture use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.13mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of workshop‑grade accuracy and robust construction to reduce inspection time and rework: the Ø6.13 mm diameter and ±0.001 mm tolerance deliver repeatable fit checks, while the 50 mm length eases access to deeper bores; order directly via Metav Werkzeuge or consult our advisers for batch supply and inventory support. Gauge pin M323.613 — Ø6.13 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.613 is a workshop‑grade test pin designed for precise end‑measure verification and fit checks in precision engineering and quality control applications. Workshop‑grade precision ±0.001 mm Diameter 6.13 mm for tight fit checks Length 50 mm for deeper bore access Supplied in protective case for transport Reduce rejects with micrometric accuracy The core advantage of this precision gauge pin is its tight dimensional tolerance of ±0.001 mm, which translates to measurable reductions in part mismatches and rework. In inspection workflows a stable reference diameter limits ambiguity during go/no‑go assessments and ensures interchangeability between mating parts. The Ø6.13 mm sizing is particularly suited to small bore gauges and end‑measure checks where clearance is minimal; the result is a faster inspection cycle and fewer downstream corrective actions. Built for the workshop: durable and easy to handle Manufactured from special steel, this test pin is prepared for routine use in workshop environments where mechanical resistance and surface integrity matter. The 50 mm length gives sufficient engagement for many bore and plug checks while remaining easy to manoeuvre by hand or in fixture setups. Supplied in a protective case, the pin is protected during transport and storage, preserving the reference surface and prolonging service life — a pragmatic choice for production floors and tool cabinets. Practical integration into inspection routines As a measuring aid, the pin functions as a simple reference for bore verification, fit trials and end‑of‑line checks. The polished shaft reduces measurement artefacts and permits swift tactile confirmation of fits. For users less familiar with gauges: a gauge pin is a hard, accurately ground shaft used to confirm that a bore or mating part meets its specified diameter — a compact and low‑complexity solution for frequent compliance checks without needing elaborate fixtures. Traceability and procurement made straightforward Identification and logistics are simplified by the clear SKU and GTIN, aiding inventory control and repeat ordering. The item is listed under measuring pins and carries the practical designation for workshop use, easing selection for production and maintenance teams. Metav’s position as a precision partner supports consistent supply: central warehousing in Emmerich and a wide product range mean fewer single‑source headaches and reliable replenishment for recurring measurement needs. Contact Metav Werkzeuge for availability of the Metav IndustryLine gauge pin M323.613 and tailored supply options; technical advice and order handling are available via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: M323.613 GTIN: 4061905060427 Manufacturer: Metav IndustryLine Facts Diameter: 6.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop version Supplied in protective case Category: measuring pins FAQ What is the dimensional tolerance of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for tight fit assessments and precision verification with minimal uncertainty. Which materials is the pin intended to test? The test pin is a hard, accurately ground reference shaft intended for checking bore diameters and fits; it provides a reliable mechanical reference for components made from common engineering materials. Is a calibration certificate supplied with the pin? No calibration certificate is included by default; the item is delivered as a workshop‑grade gauge pin without an official calibration document. Can the pin be used as a master reference in measurement labs? The pin serves well for routine fit and go/no‑go checks; for laboratory master references with formal traceability, a laboratory calibration and certificate would be recommended. Is a case supplied for transport and storage? Yes, the gauge pin is supplied in a protective case to shield the shaft during transport and to reduce handling damage before use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.14mm Gauge Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, sub-micron repeatability and convenient transport packaging for dependable reference measurements; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.614 — 6.14 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.614 designed as a single reference pin for precise diameter checks and go/no‑go verification in workshop and inspection tasks. Precision tolerance ±0.001 mm Nominal diameter 6.14 mm 50 mm length, workshop version Special steel construction, transport case included Precise reference for fast, repeatable diameter checks The M323.614 serves as a compact, high‑precision reference for diameter verification where tight tolerances are essential. With a declared tolerance of ±0.001 mm, the cylindrical gauge provides the stability required for short comparative checks and fixture set‑up, reducing cycle time in routine inspection. The 6.14 mm nominal size and 50 mm overall length make it suitable for checking bores, pin fits and mating features where a reliable go/no‑go condition or a reference master is required. The specification supports efficient decisions in quality control processes by providing an unambiguous physical standard for pass/fail evaluation. Durable construction for daily workshop use Manufactured in special steel and specified as a workshop version, the pin balances wear resistance with dimensional stability for repeated handling. At approximately 0.015 kg, the component is easy to manoeuvre while remaining robust against incidental knocks typical in production environments. The delivery includes a transport case, protecting the gauge during storage and transit and helping to preserve the measured reference over time. These characteristics ensure that routine use on the shop floor does not compromise accuracy, so inspection intervals can be kept tight without increasing replacement costs. Practical integration into established metrology workflows This cylindrical reference element complements handheld and bench measurement tools by providing an immediate, tactile verification step that integrates with existing inspection routines. When used alongside calipers and dial gauges, the pin shortens inspection sequences by offering an exact physical dimension against which instruments or components can be compared. The clear numeric tolerance and compact form factor support traceable in‑process checks and quick fixture validation, enhancing throughput and reducing uncertainty in daily production checks. Reliable choice backed by Metav's supply chain and service Sourcing from Metav IndustryLine secures access to Europe‑centred logistics and a quality‑focused distribution hub in Emmerich. The gauge pin is supplied ready for immediate use in workshop applications; Metav's broad product range and longstanding market presence provide a dependable supply route for replacements or additional sizes. For specialised measurement chains or advice on selecting complementary reference standards, Metav Werkzeuge can provide pragmatic guidance to align the pin with specific application requirements. Contact Metav Werkzeuge for application advice and to secure the M323.614 gauge pin with prompt delivery from Emmerich Technical data Article number: M323.614 GTIN: 4061905060434 Description: Gauge pin, single, 6.14 mm, ±0.001 mm, length 50 mm Facts Diameter: 6.14 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Workshop version Delivered in transport case FAQ What is the declared tolerance of this gauge pin? The M323.614 gauge pin is specified with a tolerance of ±0.001 mm, offering sub‑micron repeatability for comparative checks. Which materials and applications suit this pin? Made from special steel, the pin is intended for general workshop inspection tasks such as bore checks, pin fits and go/no‑go verifications in metalworking and assembly environments. Does the delivery include protection for transport and storage? Yes, the gauge pin is supplied in a transport case to protect the reference surface during transit and workshop storage. How does this pin fit into existing inspection processes? The pin acts as a tactile reference for quick comparative measurements and fixture validation, complementing calipers and dial gauges to shorten inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.15mm Gauge Pin Single, Workshop Version, ±0.001mm Accuracy, 50mm Length, Special Steel, Supplied in Case - Metav IndustryLine
Taking advantage of Ø 6.15 mm, ±0.001 mm tolerance and a 50 mm length ensures reliable end‑measurements and consistent fit verification in workshop inspection routines; the workshop‑grade construction and special steel deliver dimensional stability under repeated use. Order the gauge pin M323.615 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.615 — single inspection pin, Ø 6.15 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.615 is a workshop‑grade inspection pin designed for precise bore and fit verification in quality control and assembly environments Workshop-grade precision pin, ±0.001 mm Diameter Ø 6.15 mm for tight bore checks Length 50 mm for deep seat verification Made from special steel for dimensional stability Precise dimension control for critical fits The gauge pin provides high‑resolution reference for bore checks and end‑measurements, combining a tight tolerance of ±0.001 mm with a nominal diameter of Ø 6.15 mm. Such precision reduces uncertainty during inspection and supports reproducible acceptance criteria for mating parts. For teams assessing press fits, plug gauges or radial clearances, this inspection pin functions as a reliable datum: the narrow tolerance helps to quickly determine whether a bore is within a specified limit or requires rework, thereby streamlining quality decisions on the shop floor. Durable workshop construction that maintains accuracy Manufactured from special steel, the pin resists wear and maintains geometry during repeated insertions and extractions. The 50 mm length offers sufficient engagement for many practical checks while keeping handling straightforward; shorter tools can twist or deflect, but this design balances stiffness with accessibility. The workshop‑grade finish eases cleaning and prevents rapid corrosion in standard production environments, which helps to preserve the calibrated dimension over many cycles and reduces the need for frequent replacement. Practical handling and integration into inspection routines As a single gauge pin, the component simplifies set‑up compared with multi‑element fixtures: it is easy to seat, easy to visualise and quick to compare against limit gauges or master pins. The compact form factor speeds routine checks at receiving inspection, in‑process control or final assembly. Traceability is supported via the SKU and GTIN entries, enabling inventory control and clear identification in inspection logs. For bench testing and small jig work the pin serves as a straightforward reference that eliminates guesswork and shortens inspection time. Fit for purpose and shop‑floor benefits Engineered for consistent performance in repetitive tasks, this inspection pin offers measurable gains in throughput and measurement confidence. The tight accuracy reduces the margin for interpretation during pass/fail decisions, which lowers scrap and rework rates. Its simple geometry and robust material mean maintenance is limited to basic cleaning and periodic dimensional checks, maintaining uptime in high‑volume production. The result is a pragmatic, accurate tool that supports repeatable quality outcomes without complex handling. For workshop enquiries or to confirm compatibility with specific inspection setups, contact Metav Werkzeuge to secure the Metav IndustryLine gauge pin M323.615 and discuss inspection integration on the production line. Technical Data Article number: M323.615 SKU: M323.615 GTIN: 4061905061042 Brand: Metav IndustryLine Version: Werkstatt-Ausführung Material: Spezial-Stahl Numbers / Core technical data Nominal diameter: Ø 6.15 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Messbereich min: 6.15 mm Messbereich max: 6.15 mm Genauigkeit versch: ±0.001 Designs / Special features Single gauge pin configuration Workshop‑grade finish Intended use: end measurements and bore verification Category: Messstifte Storytrigger: endmasse FAQ What material is the pin made from? The gauge pin M323.615 is manufactured from special steel, giving good wear resistance and dimensional stability for routine workshop use. Is the tolerance sufficient for precision fitting checks? Yes, the ±0.001 mm tolerance of this inspection pin supports verification of tight fits and small clearances where micrometre‑level accuracy is required. For which applications is the pin intended? The inspection pin is intended for end‑measurements, bore verification and fit checks in receiving inspection, in‑process control and assembly procedures. Does the pin include a traceable identifier for inventory and QC? The product is listed with SKU M323.615 and GTIN 4061905061042, enabling clear identification in inventory and inspection documentation. How should the pin be cared for to preserve accuracy? Regular cleaning after use, gentle handling to avoid knocks and periodic dimensional verification are recommended to maintain the pin's accuracy and service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.16mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
A compact inspection solution that pairs ±0.001 mm accuracy with a 6.16 mm diameter and a robust special steel construction, making it ideal for repeatable end‑measure checks in workshop environments. Supplied as a single, 50 mm long gauge pin for straightforward integration into inspection routines — order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.616 — 6.16 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.616 is a single precision pin designed for end‑measure verification and go/no‑go checking in workshop and inspection settings. Workshop version for daily shop use Diameter precisely 6.16 mm Tolerance ±0.001 mm for high repeatability Length 50 mm, compact and easy to handle Precise measurement where it matters This single gauge pin delivers ±0.001 mm tolerance for demanding inspection tasks, translating into reliable go/no‑go decisions and reproducible end‑measure checks. The fine accuracy stabilises quality control processes by reducing measurement uncertainty at the point of contact; when combined with consistent handling, the result is fewer rework cycles and a clearer pass/fail signal on component inspection. The 6.16 mm diameter is held to tight tolerances to ensure repeatable fitment in gauges and fixtures. Tough workshop construction for everyday use Engineered as a workshop version, the pin is made from special steel that stands up to routine handling without compromising metrology properties. At 50 mm length and approximately 0.015 kg, it balances stiffness with ease of manipulation, simplifying insertion into jigs and test fixtures. Supplied individually and protected for transport in a case suitable for workshop environments, the construction minimises surface damage and preserves the reference diameter between uses. Practical applications and system integration Ideal for end‑measure verification, fixture checks and dimensional validation, the pin suits use in incoming inspection, assembly stations and maintenance workshops. The single‑piece design supports quick replacement in modular gauge systems and straightforward inclusion in calibration routines. Its compact size and precise diameter make it appropriate for checking bore quality, locating features and verifying mating parts where a defined reference diameter is required. For robust, repeatable inspection choose the Metav IndustryLine gauge pin M323.616 — contact Metav Werkzeuge for technical guidance or to arrange supply from our Emmerich centre Technical Data Article number: M323.616 GTIN: 4061905061448 ECLASS: 21170231 Designation: Gauge pin, single, 6.16 mm, ±0.001 mm, length 50 mm Facts Diameter: 6.16 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop version Supplied individually in a protective transport case Suitable for end‑measure and go/no‑go tasks FAQ What inspection tasks is this gauge pin best suited for? The gauge pin M323.616 is intended for end‑measure verification, go/no‑go checking and fixture validation where a 6.16 mm reference diameter and ±0.001 mm precision are required. Is the pin supplied as a single item or in a set? This offering is a single gauge pin (SKU M323.616), supplied individually and protected for transport to preserve the measuring surface. What material is used and how does that affect use? Made from special steel, the pin combines wear resistance with dimensional stability, supporting frequent use in workshop inspection without rapid degradation. Can this pin be used in fixture systems and gauge blocks? Yes; the pin’s tight tolerance and compact 50 mm length make it suitable for integration into fixtures and modular gauge systems for reliable mating and measurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.17mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of sub‑micrometre accuracy, workshop‑ready robustness and compact length for reliable end‑dimension inspection. Order the gauge pin directly via Metav Werkzeuge or request technical clarification from our consultants to ensure seamless integration with existing gauges and fixtures. Gauge pin M323.617 — precision test pin, 6.17 mm ±0.001 mm, 50 mm A gauge pin M323.617 designed for precise end‑dimension checks and workshop gauging tasks in machining and quality control environments. 6.17 mm diameter ±0.001 mm accuracy 50 mm length for deeper bore access Special steel for high wear resistance Workshop version delivered in protective case Consistent one‑micrometre precision for end‑dimension control The instrument delivers ±0.001 mm tolerance, corresponding to 1 µm resolution, which translates into significantly more reliable pass/fail decisions during final inspection. Such fine accuracy reduces uncertainty in end‑dimension verification and helps to cut rework rates; the precision is suitable for tight tolerance seats, pins and mating bores where reproducibility matters. Where traceable measurement is required, the pin’s specification supports integration into calibrated inspection routines and fixture checks. Robust construction that stands up to workshop use Manufactured from special steel and specified as a workshop version, the pin combines surface durability with a compact form factor. The 50 mm length permits access to deeper features while keeping handling straightforward; the low mass supports rapid gauging cycles without undue operator fatigue. Delivery in a protective case safeguards the finish during transport and storage, maintaining the contact geometry that underpins repeatable measurements. Practical applications and compatibility with inspection workflows Intended primarily for end‑dimension inspection, the pin is a versatile tool for bench gauging, fixture validation and batch end‑checking. The compact diameter of 6.17 mm makes it suitable for fine hole and bore verification where micro‑accuracy is required. Integration into existing gauge sets is straightforward: the component’s consistent geometry and workshop rating mean it can be used in manual or semi‑automated checking stations as a reference element or functional gauge. For reliable end‑dimension inspection using Metav IndustryLine precision parts, request the M323.617 gauge pin through Metav Werkzeuge for expert guidance and dependable delivery — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.617 GTIN: 4061905061455 SKU: M323.617 Material: Special steel Accuracy: ±0.001 mm Length: 50 mm Diameter: 6.17 mm Weight: 0.015 kg Facts Diameter: 6.17 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Workshop execution Delivered in protective case for transport Intended for end‑dimension inspection Compact, low‑mass design for rapid handling FAQ What is the measurement tolerance of this gauge pin? The gauge pin M323.617 has a specified tolerance of ±0.001 mm, equal to 1 µm, suitable for high‑precision end‑dimension checks. Which materials is the pin suitable for checking? The pin itself is made from special steel and is intended as a reference element for inspection of machined components; compatibility with specific workpiece materials depends on the inspection method rather than the pin material. Is the gauge pin supplied ready for use in workshops? Yes, this workshop version is supplied in a protective case to preserve the contact surface during transport and handling. Can the pin be integrated into existing fixtures or gauge blocks? The compact diameter and standard geometry make the pin suitable for use as a reference in fixtures, gauges and manual checking stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.18mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy, robust workshop design and traceable identification for reliable end‑measurement tasks; order the single gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.618 — 6.18 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.618 is a single precision test pin for end‑measure verification and plug‑gauge tasks in workshop and inspection environments. ±0.001 mm tolerance for sub‑micron checks 6.18 mm diameter for end‑measure standards 50 mm length for versatile positioning Special steel, workshop version for durable use Accuracy that reduces uncertainty in inspection The central advantage of this precision test pin is its ±0.001 mm tolerance, which corresponds to a one‑micrometre limit and significantly lowers measurement uncertainty in critical fit and end‑dimension checks. By using a reference pin with such a tight specification, inspection routines become more reproducible and allow for clear go/no‑go assessment when validating mating parts. The tight tolerance is especially beneficial where small clearances determine assembly performance, as the single pin offers a fast, objective measure compared with subjective visual or feel‑based checks. Built for workshop handling and repeatability Made from special steel and specified as a workshop version, the pin combines wear resistance with practical handling for regular use. The 50 mm shank provides comfortable engagement in gauges, jigs or fixture sockets while the compact mass supports quick temperature equalisation to ambient conditions, reducing thermal drift during short checks. Robustness translates into fewer replacements and more consistent outcomes over time, which supports production continuity and reduces rework. Practical use and system integration As a single gauge pin for end‑measure tasks, this component suits inline checks, manual plug tests and setup operations where a defined reference diameter is required. The nominal 6.18 mm diameter is useful as a control measure for bores and mating features in precision assemblies. Labelling and clear identification facilitate traceable inspection records; pairing the pin with calibrated master gauges or digital measurement logs ensures results are auditable. For operations seeking straightforward, repeatable inspection steps, the pin streamlines decision points without complex fixturing. For dependable sub‑micron end‑measure verification, contact Metav Werkzeuge to discuss the M323.618 gauge pin and application‑specific recommendations from our specialists Technical Data Article number: M323.618 GTIN: 4061905061462 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 6,18mm, +/- 0.001 mm Länge 50 mm Core specifications Diameter: 6.18 mm Tolerance/accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Features & materials Material: Special steel Version: Workshop execution Single test pin for end‑measure verification Intended use: Reference/plug checks FAQ What is the exact tolerance of the pin? The M323.618 gauge pin is specified at ±0.001 mm, providing one‑micrometre level tolerance for precise end‑measure checks. For which inspection tasks is this pin suitable? This single test pin is intended for end‑measurement and plug‑gauge checks, making it suitable for dimensional verification of bores, fit tests and setup controls in workshop and inspection processes. What material is used for the pin and why does it matter? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under normal workshop conditions, which prolongs service life and maintains repeatability. Can the pin be used as a reference in traceable measurement routines? Yes. The M323.618 functions as a straightforward reference artefact; when combined with calibrated masters or documented procedures, it supports auditable inspection results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.19mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.001 mm dimensional accuracy and a 50 mm functional length for dependable end-measurement and gauge-setting tasks. Order the pin directly via Metav Werkzeuge or request specification advice from Metav's consultants. M323.619 Gauge Pin — single gauge pin, 6.19 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.619 gauge pin is a workshop-grade, single end-measurement pin designed for precise plug and end-gauge tasks in quality control and inspection routines across mechanical workshops and metrology benches. Workshop-grade construction Diameter precisely 6.19 mm Tolerance ±0.001 mm for accuracy Supplied in protective transport box Reduce inspection uncertainty with micrometric tolerance The precision ±0.001 mm tolerance ensures that the pin performs reliably in pass/fail checks and gauge setting, reducing measurement uncertainty in repeat inspections. As a hard-ended, single-piece measuring pin, it delivers a consistent reference for go/no-go assessments and end-stop calibration. This level of accuracy supports traceable in-process checks and contributes to predictable quality output across production batches. Durable build for repeatable measurements in workshops Manufactured from special steel and finished for workshop use, the pin withstands the routine handling typical of industrial metrology. The robust material selection and compact geometry preserve dimensional stability during repeated seating and extraction cycles, which helps to keep instrument wear low and maintenance intervals predictable. The compact form factor also minimises the risk of deflection, supporting reproducible contact geometry for end-measurement tasks. Practical handling and integration into inspection workflows With a nominal diameter of 6.19 mm and a 50 mm usable length, the pin is suited to tight-fit checks, fixture set-up and end-measurement roles where precise datum control is required. Supplied in a transport box for secure shipping, the component is ready for storage or immediate use at the workshop bench. Its straightforward geometry allows fast visual identification and simple integration into existing gauge stacks or fixture insertions without special adapters. Contact Metav Werkzeuge today for application guidance or to request this Metav IndustryLine gauge pin with guaranteed workshop packing and specification details Technical data Article number: M323.619 GTIN: 4061905061479 Manufacturer: Metav IndustryLine Facts Diameter: 6.19 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Workshop version Material: Special steel Supplied in transport box for safe shipping Single gauge pin for end-measurement applications FAQ What is the declared tolerance of this gauge pin? The M323.619 gauge pin is manufactured to a tolerance of ±0.001 mm, providing micrometric repeatability for inspection and gauge-setting tasks. Is the pin supplied ready for workshop use? The pin is delivered as a workshop-grade component in a protective transport box and is suitable for immediate integration into inspection setups. What material is used for the pin? The component is made from special steel, selected for dimensional stability and resistance to routine handling typical of workshop metrology. For which tasks is this gauge pin intended? The pin is intended for end-measurements, plug and go/no-go checks, and as a reference element for setting gauges and fixtures in quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.1mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometric accuracy, compact dimensions and robust workshop design to speed up end‑measure checks and reduce rework. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for tailored inspection advice. Gauge Pin M323.610 — Single precision test pin, 6.10 mm dia, ±0.001 mm A Gauge Pin M323.610 is a single test pin designed for precise end‑measure verification in workshop and shop‑floor inspection tasks. Precision tolerance ±0.001 mm Diameter 6.10 mm, ground finish Length 50 mm for end‑measure checks Supplied in transport case Precision that removes doubt The nominal 6.10 mm diameter and the ±0.001 mm tolerance are intended for applications where repeatable end‑measure verification is critical. Ground and finished to tight limits, the pin functions as a reference standard for plug checks, calibration fixtures and comparative gauges, giving a clear quantitative basis for acceptance or rejection decisions. The micro‑scale tolerance reduces uncertainty in pass/fail assessments and shortens decision cycles in quality control. Robust construction for everyday workshop use Made from special steel, the test pin combines corrosion‑resistant surface quality with the stiffness required for repeated seating in bores and fixtures. The workshop version denotes a build optimised for frequent handling: low mass (approx. 0.015 kg) and a 50 mm shank length that is long enough for stable seating yet compact for tight setups. Supplied in a dedicated transport case, the item reaches the bench protected against knocks and contamination, maintaining accuracy between uses. Integrates into inspection routines with minimal effort As a single test pin for end measures, the component is suitable for quick go/no‑go checks, pin‑gauge stacks and fixture templates. Its defined diameter and length simplify documentation of measurement steps and support traceable inspection procedures. The compact size and consistent geometry permit rapid swapping in jigs and checking stations, improving throughput on repetitive tasks while preserving metrological reliability. Procurement confidence and operational benefits Sourcing this gauge pin through a specialist distributor contributes to reliable supply and consistent quality. Metav’s emphasis on democratising precision ensures availability and practical aftermarket guidance, reducing the administrative effort for procurement teams. Combined with clear technical data and workshop‑oriented packaging, the product supports a straightforward integration into established quality workflows. Contact Metav Werkzeuge for expert advice on integrating this Metav IndustryLine gauge pin into inspection routines and to discuss supply options tailored to current production needs. Technical data SKU: M323.610 GTIN: 4061905060397 Brand: Metav IndustryLine Facts Diameter: 6.10 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What is the intended use of this gauge pin? The gauge pin M323.610 is designed for precise end‑measure verification, plug checks and fixture reference tasks on the shop floor. Is the tolerance of ±0.001 mm sufficient for calibration references? Yes, the ±0.001 mm tolerance makes the M323.610 suitable as a reference in many workshop inspection scenarios where micrometric precision is required. Can this pin be used in automated inspection jigs? The compact diameter and consistent geometry of the gauge pin permit integration into jigs and automated fixtures where a single reference pin is needed. How is the gauge pin protected during storage and transport? The product is supplied in a transport case to protect the finished surface and preserve dimensional integrity between uses. Which material is used and what are its advantages? Constructed from special steel, the pin offers a combination of surface stability and mechanical stiffness appropriate for frequent seating and repetitive inspection operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.21mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
High-precision gauge pin with a 6.21 mm diameter and ±0.001 mm tolerance delivers repeatable end‑measurements; the 50 mm length and workshop-grade construction ensure robust handling and traceable checks. Order the gauge directly via Metav Werkzeuge or consult our advisors for batch supply and technical guidance. Gauge pin M323.621 (6.21 mm, ±0.001 mm) — Metav IndustryLine workshop version The Gauge pin M323.621 is a workshop-grade inspection pin designed for high-precision end‑measurement, plug and ring checks and fixture set-up in maintenance and production environments. Workshop-grade precision ±0.001 mm Diameter 6.21 mm ground to tolerance 50 mm special steel shaft for dependable wear resistance Delivered in protective transport case Repeatable accuracy where it matters Precision is the primary value of this inspection pin. With a specified tolerance of ±0.001 mm, the pin supports reliable go/no‑go and comparative checks that reduce uncertainty during incoming inspection or in‑process control. The compact diameter of 6.21 mm and moderate 50 mm length make the item suitable for tight bores and confined measuring spaces, while the fine tolerance helps to detect minute deviations that would otherwise affect assembly or function. The technical specification is ideal for workshop applications where small form‑factor precision tools are required. Built for workshop use and sustained service life The workshop version is engineered for everyday inspection routines. Manufactured from special steel, the shaft offers a balance of hardness and toughness that resists rapid wear under repeated contact inspections. The single‑piece supply simplifies inventory selection for toolrooms and gauges, and delivery in a protective transport case preserves the ground surface and concentricity during storage and transit. Together, these attributes lower the total cost of ownership by extending service intervals and maintaining measurement integrity between checks. Integrates cleanly into quality control processes As a precision inspection element, this gauge pin fits directly into established quality workflows: setting ring gauges, verifying bore diameters, and confirming fit tolerances on assemblies. The compact format supports rapid interchange and reduces handling time on the shop floor, contributing to faster inspection cycles and more consistent acceptance decisions. For those tracking inventory or referencing product data, the item is listed under SKU M323.621 and is supplied as an individual gauge pin suitable for routine dimensional control tasks. For sample requests, calibration options or volume supply, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or by email at info@metav-werkzeuge.com for personalised advice and delivery details Technical data Article number: M323.621 GTIN: 4061905061493 Brand: Metav IndustryLine Specifications Diameter: 6.21 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Features Workshop version Material: Special steel Supplied individually Protective transport case included FAQ What tolerance does this gauge pin provide? The inspection pin is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑measurement. What material is the shaft made from? The shaft is manufactured from special steel intended for workshop use and durable contact inspections. Is the gauge pin supplied individually or as a set? This item is supplied as an individual gauge pin under SKU M323.621. Which inspection tasks is this pin intended for? Typical uses include plug and ring checks, bore verification and fixture set‑up where a compact, precision pin is required. Does the product description include a calibration certificate? The product data does not specify an included calibration certificate; calibration status is not stated. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.22mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade precision, a tight ±0.001 mm tolerance and a compact 50 mm length for reliable inspection and repeatable assembly checks; order the gauge pin directly via Metav Werkzeuge or consult the Metav experts for application advice. Gauge pin M323.622 — Test pin, 6.22 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.622 is a single precision test pin intended for dimensional inspection and reference checks in workshop and production environments Diameter 6.22 mm precision Tolerance ±0.001 mm Length 50 mm workshop version Special steel construction Consistent dimensional control for everyday inspection tasks The compact design of this test pin delivers a clear benefit where repeatability matters: the nominal diameter 6.22 mm combined with a certified ±0.001 mm runout tolerance supports tight go/no‑go checks and reference measures. In practical terms, the small mass and controlled geometry reduce handling variation during sequential checks, improving repeatability on the shop floor. The specified 50 mm length offers sufficient engagement for bore and plug inspections while remaining easy to handle in jigs and fixtures. This balance of dimensions and tolerance translates directly into fewer measurement-related reworks and steadier quality control routines. Robust handling and fit for production environments Constructed from special steel, the pin is designed for stable dimensional behaviour under routine use and provides a reliable seating for comparative gauging and fixture set‑ups. The plain cylindrical form minimises seating errors and simplifies alignment in distinguishing bore limits or establishing reference lengths. Where quick, unequivocal verification is required during assembly or incoming‑goods inspection, the compact test pin serves as a fast, deterministic check that integrates with manual and semi‑automated inspection processes. The modest weight makes it convenient for bench tasks and for inclusion in inspection sets without affecting ergonomics. Integration into metrology workflows and documentation As an inspection tool from Metav IndustryLine, the pin is intended to complement existing measurement artefacts and gauge blocks in a calibrated toolbox. Its use-case extends from quick pass/fail checks to inclusion as a control gauge in first‑article inspection reports. The clearly defined tolerance band simplifies statistical process control entries and helps to document measurement traceability when logged with batch or process data. For customers requiring catalogue and traceability alignment, the item’s SKU and GTIN facilitate stockkeeping and integration into procurement or calibration records. Secure precise reference parts from Metav Werkzeuge — order the Metav IndustryLine M323.622 gauge pin or contact the Metav team in Emmerich for technical matching to specific inspection tasks Technical Data Article number: M323.622 GTIN: 4061905061509 Brand: Metav IndustryLine Type: Single gauge pin / test pin Data Diameter: 6.22 mm Length: 50 mm Tolerance / accuracy: ±0.001 mm Weight: 0.015 kg Special features Workshop version Material: Special steel Single item delivery SKU: M323.622 FAQ What is the primary use of this gauge pin? The gauge pin M323.622 is intended for dimensional inspection and reference checks, used as a go/no‑go or seating reference in bore and plug verification tasks. Does the pin meet very fine tolerance requirements? Yes, the pin is specified with a tolerance of ±0.001 mm, suitable for high‑precision shop and inspection applications where tight limits are required. Which material is the pin made from and what does this mean for durability? The pin is made from special steel, offering stable dimensional behaviour and wear resistance appropriate for regular inspection cycles in production environments. Can this pin be used in fixture set‑ups and jigs? Its 50 mm length and cylindrical form make it suitable for integration into fixtures and jigs as a reference element for alignment and verification tasks. How is the part identified for procurement and inventory? Stock and procurement reference is SKU M323.622 with GTIN 4061905061509 for clear traceability in ordering and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.23mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance, compact dimensions and robust workshop design for reliable end‑dimension checks; the test pin is delivered in a transport case for safe handling and quick storage. Order the M323.623 gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin M323.623 — precision 6.23 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.623 is a single precision test pin designed for rapid end‑dimension verification in workshop and production metrology, offering micron‑level repeatability for small‑part inspection. Precision tolerance ±0.001 mm Diameter 6.23 mm, length 50 mm Made from special steel Supplied in a transport case Engineered for dependable end‑dimension verification This compact test pin delivers an exact 6.23 mm nominal diameter with a ±0.001 mm tolerance, which places it in the high‑precision band for plug gauges and test pins. The tight tolerance supports reliable go/no‑go checks and repeatable measurement routines, reducing rework and downtime. As a solid test pin, it is particularly suitable for quick inspection of bore end‑masses and final dimensional checks where micrometre accuracy matters. Robust handling and workshop suitability Constructed from special steel in a workshop‑grade configuration, the pin balances wear resistance with manageable weight for daily use. The 50 mm length provides sufficient engagement in typical small bores while keeping handling straightforward on the shop floor. Supplied in a transport case, the item is protected in transit and ready for secure storage on the bench, preserving the measuring surface and extending service life. Traceability and integration into inspection routines The simple geometry and precise manufacturing of this plug gauge facilitate integration into standard inspection flows and fixture checks. Its repeatability makes it a pragmatic choice for batch verification and final QA gates, supporting process stability and clear pass/fail criteria. For those seeking a trusted supply chain partner, Metav Werkzeuge’s quality filter in Emmerich ensures consistent product availability and traceable sourcing for measurement tools. Contact Metav Werkzeuge in Emmerich for tailored application advice and swift supply of the M323.623 gauge pin Technical Data Article number: M323.623 GTIN: 4061905062322 Label: Prüfstift, einzeln, 6,23mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.23 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Version: Workshop design Supplied in transport case FAQ What tolerance does this test pin provide? The M323.623 gauge pin is manufactured to a tolerance of ±0.001 mm, offering micrometre‑level accuracy suitable for final dimensional checks. For which applications is this plug gauge intended? This precision pin is intended for end‑dimension verification and go/no‑go checks in production and workshop metrology, where small‑bore inspection and repeatable pass/fail criteria are required. How is the M323.623 delivered and protected? The gauge pin is supplied in a transport case to protect the measuring surface during storage and transit, preserving accuracy between uses. Can the pin be used for routine inspection on the shop floor? Yes, the workshop version of the M323.623 is designed for regular use in inspection stations and bench checks, combining robustness with precise geometry. Is the M323.623 suitable for integration into existing inspection fixtures? Its compact diameter and consistent manufacturing make the gauge pin straightforward to incorporate into fixtures for batch inspection and quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.24mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme measuring precision, a compact 50 mm length and robust special steel construction to secure repeatable end‑dimension checks and reduce rework. Order the pin gauge directly via Metav Werkzeuge or consult the product advisors for application matching. Pin gauge M323.624 — single workshop‑grade gauging pin, Ø 6.24 mm, tolerance ±0.001 mm The Pin gauge M323.624 is a single, workshop‑grade measuring pin designed for reliable end‑dimension verification and go/no‑go fits in production and inspection environments Workshop‑grade precision construction Diameter 6.24 mm, tolerance ±0.001 mm 50 mm length for stable handling and reach Single unit delivery for targeted checks Precision that secures final dimensions The M323.624 delivers an exceptional ±0.001 mm tolerance on a nominal 6.24 mm diameter, making it suitable where micrometric conformity determines pass or fail at the final inspection stage. Such a tight tolerance removes ambiguity from end‑dimension checks and shortens decision paths on the shop floor: measurement results become comparable across shifts and machines, lowering scrap rates and reducing subsequent rework. The specification is especially valuable when used as a reference gauge in assembly jigs or as a benchmark during tool set‑up, where repeatable results are essential for production continuity. Robust build for everyday workshop use Manufactured from special steel, this single pin is intended for workshop environments and designed to withstand frequent handling without compromising accuracy. The 50 mm length provides a compromise between reach and rigidity, ensuring stable contacts in small bores or on turned parts while remaining easy to manoeuvre by hand. At approximately 0.015 kg the gauge is lightweight yet stiff enough to give reproducible readings; the compact form factor reduces the risk of levered deflection during measurement and supports faster inspection cycles in busy production lines. Practical applications that improve throughput This gauging pin is primarily intended for end‑dimension verification of shafts, holes and turned components, serving as a fast reference for go/no‑go decisions and routine quality control. Used in incoming inspection, in‑process checks and final acceptance, it supports a logic of quick, objective measurement rather than prolonged subjective assessment. The workshop execution makes it a dependable choice for maintenance shops, small batch production and fixture set‑ups where a precise, single‑diameter reference is required to maintain assembly tolerances and safeguard downstream processes. Contact Metav Werkzeuge today to confirm suitability of the M323.624 pin gauge for specific measurement tasks and to arrange supply directly from Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M323.624 GTIN: 4061905062339 Article: Pin gauge, single, Ø 6.24 mm, ±0.001 mm Facts Diameter: 6.24 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop execution Single unit delivery Intended for end‑dimension checks FAQ What level of accuracy does the pin provide? The M323.624 pin gauge (Metav IndustryLine, pin gauge SKU M323.624) is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑dimension checks. Which measurement tasks is this gauge intended for? This single pin gauge is made for end‑dimension verification of shafts, bores and turned components and is suitable as a rapid go/no‑go reference in workshop and production inspection. What material is the pin made from and how does that affect use? The pin is produced from special steel, giving robust handling characteristics appropriate for workshop environments while maintaining the dimensional stability required for repeatable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.25mm Gauge Pin ±0.001 mm Length 50 mm Workshop Finish - Metav IndustryLine
Take advantage of workshop‑grade construction, special‑steel durability and an exceptionally fine tolerance of ±0.001 mm to secure repeatable end‑measurement checks and jigging operations; order the gauge pin directly via Metav Werkzeuge or request advice from our consultants for batch requirements. M323.625 Gauge pin (6.25 mm, ±0.001 mm) — Metav IndustryLine The M323.625 gauge pin is a workshop‑grade precision plug designed for end‑measurements, go/no‑go checks and fixture setting in metrology and toolmaking environments. Precision tolerance ±0.001 mm Workshop‑grade special steel Length 50 mm for end measurements Delivered in a transport case High precision for consistent pass/fail verification The M323.625 is manufactured to an exacting tolerance of ±0.001 mm, which supports consistent go/no‑go assessments and dimensional spot checks on machined parts. That level of accuracy reduces the need for secondary verification and speeds up in‑process inspection, so batch acceptance decisions are based on reproducible, measurable criteria. The slim form makes the device suitable for plug and seat checks where surface conformity and bore concentricity are critical. Robust workshop design that withstands daily use Constructed from special steel and specified as a workshop‑grade tool, the pin is finished to resist wear from frequent handling and contact with mating parts. The 50 mm shank provides a stable reference length for end measurements and is long enough for most fixture and gauge applications while remaining easy to position. Supplied individually and protected for transit in a secure transport case, the component arrives ready for immediate use in production or toolroom environments. Fits into inspection workflows with clear traceability Marked with SKU M323.625 and the GTIN for inventory control, the pin integrates into standard inspection processes and documentation routines. Its small mass and compact dimensions allow simple handling and rapid changeover between checks, supporting lean metrology practices on the shop floor. Backed by Metav’s distribution and quality focus, the item benefits from a supply chain that emphasizes availability and consistent product quality for industrial and trade customers. Contact Metav Werkzeuge to discuss batch availability, sample inspection or to arrange delivery from Emmerich for your metrology and fixture needs Technical Data Article number: M323.625 GTIN: 4061905058790 SKU: M323.625 Facts Diameter: 6.25 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Workshop‑grade design Material: special steel Delivered in transport case Single item supply FAQ What accuracy can be expected from this gauge pin? The M323.625 gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision pass/fail checks and precise fixture setting. Is the pin suitable for routine shop‑floor inspection? Yes, the workshop‑grade construction and protective transport case mean the gauge pin is designed for regular use in production and toolroom environments. Which material is used for the pin? The pin is made from special steel, chosen for wear resistance and dimensional stability during repeated contact inspections. How is the product identified for stock and traceability? The item is supplied with SKU M323.625 and the GTIN 4061905058790 for inventory control and documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.26mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combining ultra‑fine tolerance and a robust workshop design ensures reliable, repeatable inspections; benefit from the ±0.001 mm accuracy and compact 50 mm length when verifying small bores. Order the M323.626 gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.626 gauge pin — 6.26 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The M323.626 gauge pin is a single, high‑precision inspection pin for micro‑range dimensional checks in workshop and production environments. High precision ±0.001 mm tolerance Compact 6.26 mm diameter for micro checks Workshop‑grade construction for daily use Supplied in a protective transport case Precision that stabilises quality control Consistent measurement reduces rework and keeps production running to plan. The test pin delivers a diameter of 6.26 mm with a guaranteed ±0.001 mm tolerance, enabling reliable go/no‑go and reference checks on small bores and mating parts. Such fine tolerance minimises acceptance variance during incoming inspection and in‑process quality gates, so fewer components are rejected for marginal deviations and process capability is easier to maintain. Built for workshop resilience and simple handling Designed as a workshop version, the pin is manufactured from special steel to combine surface hardness with dimensional stability. With a length of 50 mm and a mass around 0.015 kg, it is straightforward to handle during manual inspection or when placed in a fixture. Delivery in a protective case reduces the risk of transport damage and helps preserve the geometry that underpins repeatable measurements, extending the useful life of the gauge. Straightforward integration into inspection routines The component supports traceable stock and quality processes via GTIN 4061905058806 and SKU M323.626, helping with inventory control and audit trails. As a micro‑range gauge (measurement range below 10 mm), the pin complements bench comparators and small‑bore fixtures, simplifying routine checks and accelerating quality verification. Because the design focuses on a single, well‑defined diameter, it is ideal for rapid verification tasks where speed and precision matter. For dependable micro‑inspection in daily production, contact Metav Werkzeuge in Emmerich to discuss how the Metav IndustryLine M323.626 gauge pin fits specific inspection workflows Technical data Article number: M323.626 GTIN: 4061905058806 Manufacturer: Metav IndustryLine Category: Gauge pin / Test pin Facts Diameter: 6.26 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: Special steel Workshop execution Supplied in a transport case Intended use: dimensional inspection of small bores FAQ What tolerance class does this pin have? The M323.626 gauge pin is specified with an accuracy of ±0.001 mm, suitable for high‑precision inspection tasks. Is the pin suitable for daily workshop use? Yes, the workshop execution and special steel construction make the inspection pin appropriate for frequent handling and routine checks. What is the measurement range classification for this item? This component falls into the micro range (measurement range below 10 mm), intended for fine mechanical and small bore applications. Does the product come with traceability identifiers? The gauge pin is identified by GTIN 4061905058806 and SKU M323.626 to support inventory and audit processes. How is the item delivered to protect dimensional integrity? The pin is supplied in a protective transport case to reduce the risk of damage in transit and preserve measurement geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.27mm Test Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial precision and robust workshop design: the gauge presents a nominal diameter of Ø 6.27 mm with an ultra‑fine tolerance of ±0.001 mm, and a compact length of 50 mm for reliable end‑measure checks. Order the M323.627 directly via Metav Werkzeuge or request technical advice from our consultants. M323.627 Test Pin (Metav IndustryLine) – Ø 6.27 mm, ±0.001 mm, 50 mm M323.627 Test Pin is a single, workshop‑grade gauge pin for precise end‑measurement and fixture‑setting tasks in inspection and production environments. Workshop‑grade special steel construction Diameter Ø 6.27 mm with ±0.001 mm tolerance Length 50 mm for compact fixtures Delivered in protective transport case Accuracy that reduces rework and speeds inspection The gauge pin is specified with a tolerance of ±0.001 mm, which translates into highly repeatable pass/fail checks at the receiving end of production sequences. This level of precision supports decisive go/no‑go decisions during inline inspection and reduces costly rework by ensuring that bore and end‑dimension checks return consistent results. The clearly defined nominal diameter Ø 6.27 mm allows easy integration into existing plug gauges and test fixtures, improving throughput in quality control operations. Material and build tailored for workshop use Manufactured from special steel and labelled as a workshop version, the pin balances dimensional stability with everyday robustness. The combination of hardened machining and precise grinding yields a component that maintains geometry under normal handling and contact loads. The low mass (approx. 0.015 kg) and compact geometry contribute to effortless handling during repetitive inspection cycles while supporting long‑term serviceability in a busy production setting. Compact design and secure transport for on‑the‑job readiness With a length of 50 mm, the pin suits confined fixturing and quick insertion tasks where short gauges are required. Delivery in a protective transport case prevents incidental damage and keeps the pin ready for immediate use at the workstation or in a portable inspection kit. This practical packaging reduces downtime caused by handling damage and helps maintain the pin’s measurement integrity between uses. Practical uses and compatibility with inspection workflows Intended primarily for end measurements and plug‑type checks, the component is useful in assembly, fixture set‑up and repetitive quality checks where a defined reference diameter is needed. Its nominal diameter and tolerance make it suitable as a precision check gauge within production sampling plans and for aligning jigs or locating features. The compact design supports easy incorporation into handheld gauge sets and bench fixtures without disrupting established workflows. For reliable end‑measurement performance, choose the Metav IndustryLine M323.627 gauge pin — contact Metav Werkzeuge for procurement and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: M323.627 GTIN: 4061905058813 Label: Test pin, single, 6.27 mm, ±0.001 mm, length 50 mm Numbers / Core technical data Nominal diameter: 6.27 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: Special steel Workshop version Delivered in protective transport case Category: Messstifte Intended use: end measurements FAQ What tolerance and diameter does the M323.627 test pin offer? The Metav IndustryLine M323.627 test pin is specified at Ø 6.27 mm with a tolerance of ±0.001 mm, designed for highly repeatable end‑measurement checks. Is the gauge pin delivered ready for safe transport? Yes, the M323.627 is supplied in a protective transport case to prevent handling damage and to keep the pin ready for immediate use at the workstation. Which material is the pin made from and what does that mean in practice? The pin is made from special steel, providing dimensional stability and resistance to normal workshop wear, which helps preserve measurement integrity during routine use. For which inspection tasks is this test pin best suited? The pin is ideal for end‑measurement checks, plug‑type inspections and fixture alignment where a compact, high‑precision reference diameter is required. Can the M323.627 be integrated into existing fixtures and gauges? Yes, the compact 50 mm length and standardised nominal diameter make the pin suitable for integration into bench fixtures, handheld gauge sets and plug‑type measurement arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.28mm Test Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the proven combination of micrometre-level accuracy, compact handling and robust workshop design to secure repeatable end measurements and fewer rework cycles; order directly via Metav Werkzeuge or contact our consultants for technical advice. Gauge pin M323.628 (6.28 mm, ±0.001 mm, 50 mm length) — Metav IndustryLine The Gauge pin M323.628 is a single precision test pin for dependable end-measure checks and bore verification in workshop and inspection environments Diameter 6.28 mm, tolerance ±0.001 mm 50 mm length, workshop execution Made from special steel Supplied in protective transport case Micrometre-level tolerance for decisive quality control The core advantage lies in the ±0.001 mm specification, which translates into measurable gains in process reliability when verifying end measures and mating fits. For short-run inspections and final acceptance, the small geometric deviation reduces false rejects and minimises downstream correction work. Because the diameter is manufactured to 6.28 mm with a narrow error band, the pin serves as a reliable reference for checking bore sizes and alignment during setup and routine quality control. The precision achieved here supports leaner inspection steps and faster go/no-go evaluations. Robust, compact design that endures workshop use Manufactured in special steel and executed as a workshop-grade component, this test pin balances hardness with corrosion resistance for everyday handling. The 50 mm length and low mass (approx. 0.015 kg) make the pin easy to manoeuvre while retaining stiffness for accurate seating in bores. Supplied in a protective transport case, the unit is protected from knocks and contamination between uses, which preserves dimensional stability and extends service life. The straightforward form factor also simplifies storage in inspection trays or gauge sets. Practical integration into inspection routines and tooling Designed for end-measure applications, this pin is suitable for direct bore checks, fixture setup and reference gauging. The compact geometry eases insertion in confined spaces and supports repeatable seating against datum faces, delivering consistent reference points for measurement chains. Supplied as a single unit with the clear designation M323.628, the pin complements standardised inspection jigs and can be used alongside callipers and micrometres to confirm critical dimensions during final inspection stages. Trusted supply chain and competence from Metav Metav IndustryLine benefits from the Metav quality filter in Emmerich, ensuring parts are sourced and handled with industrial discipline. The combination of clear traceability, a broad product range for workshops and a long-standing distribution network provides practical reassurance when specifying precision components. Metav’s portfolio and advisory capability help integrate measurement items such as this pin into everyday inspection infrastructure, supporting higher first-pass yields and dependable delivery performance. For reliable end measurements and workshop-ready inspection tooling, contact Metav Werkzeuge in Emmerich for availability and technical pairing advice — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the M323.628 gauge pin and suitable complementary gauges Technical data Article number: M323.628 GTIN: 4061905058820 Label: Prüfstift, einzeln, 6,28mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 6.28 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop execution Supplied in protective transport case Intended application: end measurements Category: Messstifte FAQ What is the intended use of this gauge pin? The gauge pin M323.628 from Metav IndustryLine is intended for end-measure checks and bore verification in workshop and inspection environments. Is the diameter tolerance suitable for high-precision fits? Yes, the ±0.001 mm tolerance of the M323.628 test pin is suitable for precision fit verification and careful end-measure assessments. What material is used and how does it affect durability? Made from special steel, the pin offers a balance of wear resistance and dimensional stability suited to regular workshop handling. Does the product come with protective packaging? The pin is supplied in a protective transport case, ensuring safe handling and reduced contamination during storage and transport. How can this pin be integrated into existing inspection workflows? The compact 50 mm length and precise diameter allow the M323.628 gauge pin to be used for fixture setup, bore checks and as a reference in multi-step inspection routines with callipers or micrometres. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.29mm Gauge Pin Single ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of a compact inspection tool that delivers repeatable end-dimension control through a combination of ultra‑fine tolerance, stable geometry and robust workshop design; the precise ±0.001 mm specification and a 6.29 mm diameter ensure reliable fits and consistent measurements in series testing. Order directly via Metav Werkzeuge or contact their consultants for tailored advice. M323.629 gauge pin (6.29 mm, ±0.001 mm) – Metav IndustryLine The M323.629 gauge pin is a single inspection pin designed for precise end‑dimension checks and tight‑fit verification in workshop and production environments. High precision tolerance ±0.001 mm Diameter 6.29 mm for tight-fit checks Length 50 mm for fixture and bore tests Workshop version, robust industrial design Precise tolerance for reproducible end measurements The core strength of this inspection pin lies in its ±0.001 mm tolerance, which makes it suitable for applications where minute dimensional deviations matter. Specified accuracy removes ambiguity when validating final dimensions on moderate‑run parts. The tight tolerance reduces rework and supports confidence in pass/fail decisions during incoming inspection and assembly verification. As a verification tool, the pin gives measurable, comparable results that integrate readily into routine quality checks. Compact geometry that suits tight bores and jigs With a 6.29 mm diameter and 50 mm overall length, the pin is engineered for insertion into small bores, locating holes and jigs where standard gauges may be too large. The compact geometry helps maintain alignment in fixtures and minimises bending or rocking during measurement, so readings remain stable. This makes the component a practical choice for bench checks and for confirming end measurements on assembled modules where accessibility and repeatability are required. Robust material choice for consistent dimensional stability Manufactured from special steel, this single test pin is produced for workshop use and regular handling. The material selection supports dimensional stability under typical shop conditions and contributes to wear resistance over many cycles. The design intent is to provide a resilient inspection aid that sustains precise contact geometry when used in standard production and maintenance routines, thereby preserving measurement quality over time. Designed for integration into inspection workflows As a single, clearly identified inspection element with a unique SKU and GTIN, the pin is easy to log into quality records and inventory systems. Its straightforward form factor allows rapid substitution in modular gauges or fixture checks and supports consistent comparison across batches. For customers seeking reliable end‑dimension control without complex setup, this gauge pin provides a direct, low‑overhead method to confirm hole sizes and locating features during the production process. For reliable end‑dimension inspection with the Metav IndustryLine gauge pin, contact Metav Werkzeuge for ordering and technical advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.629 GTIN: 4061905058837 Category: Gauge pins Brand: Metav IndustryLine Facts Diameter: 6.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop version Single inspection pin Application: end‑dimension checks FAQ What is the declared tolerance of this inspection pin? The declared tolerance is ±0.001 mm for the M323.629 gauge pin, providing high‑precision control for end‑dimension verification. For which applications is this pin intended? This single test pin is intended for tight bore inspection, fixture checks and end‑dimension control in workshop and production environments. What material is used for the pin? The pin is made from special steel to offer dimensional stability and durability under routine inspection use. How long is the pin and which diameters does it suit? The pin has a length of 50 mm and a diameter of 6.29 mm, suited for small bores and locating features. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.2mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Grade - Metav IndustryLine
Take advantage of ultra‑fine tolerance (±0.001 mm) and a hard-wearing special‑steel construction combined with a compact 50 mm length for reliable end‑measure checks in everyday workshop use; order the M323.620 gauge pin directly via Metav Werkzeuge or consult our specialists for application guidance. M323.620 Gauge Pin — 6.20 mm, ±0.001 mm (Metav IndustryLine) The M323.620 is a single gauge pin designed for precise end‑measurement and fit checks in workshop environments, offering a compact 50 mm length and laboratory-grade dimensional stability. Ultra-fine tolerance ±0.001 mm Precisely ground Ø 6.20 mm Robust special-steel construction Workshop execution, length 50 mm Precision that shortens inspection cycles The M323.620 gauge pin was engineered to provide a clear, measurable benefit: repeatable dimensional control with a declared accuracy of ±0.001 mm. This level of precision minimises rework and reduces the time spent on secondary checks, making the gauge pin a practical tool for entry checks, end‑measure verification and go/no‑go fits. The 6.20 mm diameter is ground to size and held to tight tolerances, which supports consistent mating with fixtures and gauges and helps maintain throughput in small‑batch production or maintenance operations. Robust design for everyday workshop use Constructed from special steel, this single test pin resists everyday wear while maintaining surface integrity over many cycles. The workshop execution emphasises practical durability: surfaces are finely ground so that contact points stay stable, while the compact 50 mm length gives sufficient reach for most assembly and inspection tasks without adding unnecessary leverage or handling complexity. The low mass (approx. 0.015 kg) facilitates quick positioning and limits inertia during repeated measurements, improving operator handling and reducing measurement scatter. Integrates into quality workflows and traceability The gauge pin is supplied as a single, traceable item (GTIN: 4061905061486) suitable for use alongside existing plug‑gauge sets or as replacement pins in inspection rigs. Clear specification—diameter 6.20 mm, tolerance ±0.001 mm, length 50 mm—allows straightforward documentation in quality records and inventory systems. Relying on such defined physical parameters supports faster decision‑making on the shop floor, while the product’s straightforward geometry eases calibration planning and storage in controlled tool cabinets. Contact Metav Werkzeuge in Emmerich to discuss how the M323.620 gauge pin fits into your inspection process and to arrange expert technical advice or tailored supply. Technical data Article number: M323.620 GTIN: 4061905061486 Label: Prüfstift, einzeln, 6,20mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.20 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pin (single) Storytrigger / Application cue: end‑measure checks FAQ What level of dimensional accuracy does this gauge pin provide? The M323.620 gauge pin is specified to ±0.001 mm, making it suitable for high‑precision fit and end‑measure checks in workshop environments. Which materials is the pin made from and how does that affect wear? Manufactured from special steel, the M323.620 offers enhanced resistance to wear and maintains contact surface quality through repeated use. Can this pin be used in existing gauge sets or fixtures? Yes, the single‑piece design and standardised diameter of 6.20 mm mean the pin integrates easily with common plug‑gauge sets and inspection fixtures. Is the length suitable for recessed fit checks? The 50 mm length provides sufficient reach for many recessed and through‑hole verifications while remaining easy to handle during repetitive checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.31mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop durability, exacting ±0.001 mm tolerance and compact handling length for reliable end‑measure checks; order the part directly via Metav Werkzeuge or consult our advisors for batch and inspection advice. Gauge pin M323.631 – Single test pin, 6.31 mm ±0.001 mm, 50 mm A gauge pin M323.631 engineered for precise end‑measure verification and quick go/no‑go checks in workshop environments. High precision ±0.001 mm tolerance Robust workshop design for daily use Manufactured from special steel for wear resistance Stable 50 mm length for repeatable handling Accurate end‑measure verification without compromise The compact measuring element delivers repeatable results thanks to its ±0.001 mm tolerance and nominal diameter of 6.31 mm. This level of accuracy permits confident verification of end‑sizes, pins and bores where tight clearances determine fit and function. The single measuring pin concept keeps handling straightforward: a well‑defined reference diameter simplifies pass/fail routines and reduces interpretation time during first‑article inspections or random batch checks. Built for everyday workshop use and longevity Constructed from special steel, the component resists wear in high‑use environments while remaining simple to clean and store. The 50 mm overall length provides sufficient gripping area for manual handling and stable seating in fixtures, while the low mass (0.016 kg) minimises the risk of slippage during quick checks. The workshop specification balances robustness with the dimensional stability required for frequent in‑process inspection, extending service intervals and lowering the total cost of ownership through reduced rework. Integrates into inspection workflows and traceability systems The design supports efficient quality control processes: the compact measuring pin fits in benches, holders and customised gauges for rapid transfer of measured values into inspection reports. For inventory and procurement, note SKU M323.631 and GTIN 4061905059810 for unambiguous identification. Specifying a high‑precision measuring element of this class reduces scrap and downstream adjustments, helping maintain throughput and assuring customers of consistent component conformity. Choose Metav IndustryLine parts from Metav Werkzeuge for workshop‑ready precision and ask our consultants about tailored inspection solutions Technical data SKU: M323.631 GTIN: 4061905059810 Manufacturer: Metav IndustryLine Key measurements Nominal diameter: 6.31 mm Length: 50 mm Mass: 0.016 kg Tolerance: ±0.001 mm Features Material: special steel Single gauge / test pin design Workshop version suitable for frequent use FAQ What tolerance does the pin provide? The gauge pin M323.631 is manufactured to a tolerance of ±0.001 mm, making it suitable for tight end‑measure checks and precision fit verification. What material is the pin made from and how durable is it? This measuring pin is made from special steel and is supplied in a workshop specification intended for regular use; the material choice supports wear resistance and stable dimensional performance. Is a calibration certificate supplied with the item? The product data does not indicate a supplied calibration certificate; calibration status should be confirmed with Metav Werkzeuge if a certificate is required for quality records. Which applications are suitable for this gauge pin? The pin is intended for end‑measure checks, go/no‑go assessments and fixture‑mounted dimensional verification in machining, assembly and quality control operations. Can the pin be used with standard holders and measuring fixtures? Yes—the single‑pin design and standard nominal diameter allow integration into common holders and bespoke fixtures; refer to SKU M323.631 for compatible accessories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com