DNMG 150412 AH8015 Wendeplatten - Tungaloy
The balanced combination of PVD-coated carbide AH8015 and a 1.2 mm corner radius delivers consistent wear resistance and edge stability for demanding turning tasks; the ISO-standard DNMG150412 geometry ensures straightforward integration into existing tool systems. Order the insert directly via Metav Werkzeuge or consult our specialists for tailored selection and application advice. DNMG150412 AH8015 – DNMG ISO rhombic turning insert for turning, Tungaloy, 55° The DNMG150412 AH8015 is an ISO-standard rhombic turning insert designed for external and internal turning, especially where heat-resistant alloys require a balance of wear resistance and cutting-edge stability. *PVD-coated carbide AH8015 *Rhombic 55° geometry, 1.2 mm radius *Double-sided chipbreaker, cylindrical hole *ISO-compatible insert, 4.76 mm thickness Reliable cutting performance for heat-resistant alloys The combination of a PVD-coated surface and a wear-resistant carbide substrate makes this grade particularly suitable for machining heat-resistant alloys. The AH8015 formulation is balanced between abrasion resistance and edge stability, which reduces the frequency of insert changes and supports a steady production pace. The coating created by the PVD process acts as a hard, thin barrier against adhesive wear and heat build-up; in practice this means longer tool life and more predictable component quality without complex process adjustments. Compatibility and secure clamping for stable processes The insert follows ISO-standard geometry, ensuring compatibility with a wide range of DNMG holders and boring bars when form, relief angle, tolerance class, fixing and plate thickness are matched. The 55° rhombic form and the cylindrical hole allow positive and repeatable seating in most tool systems, while the 0° relief angle supports stable cutting conditions in both external and internal turning. Using a properly matched holder, shim and clamping set minimises vibration and runout, which in turn improves surface finish and dimensional consistency. Practical design that improves productivity and surface quality A double-sided chipbreaker and a 1.2 mm corner radius are engineered to support controlled chip formation and a reliable cutting edge radius, which benefits surface integrity on the workpiece. The insert’s 4.76 mm thickness and rhombic plate form provide robust support during interrupted cuts and heavier depths of cut. System assembly is straightforward: insert, appropriate holder or boring bar, underlay/clamping set and spare screws — a practical setup that reduces downtime and simplifies tool management on the shop floor. For an application-specific recommendation or to acquire this Tungaloy turning insert, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and rapid order handling Technical Data Article number: 6947157 Manufacturer SKU: TUN6947157 SKU: 6947157-Tungaloy Model series: ISO turning inserts Designation: DNMG150412 AH8015 Material: Carbide Facts Cutting angle: 55° Corner radius: 1.2 mm Relief angle: 0° Plate size: 15 mm Plate thickness: 4.76 mm Special features PVD-coated carbide Grade AH8015 for heat-resistant alloys Rhombic plate form Double-sided chipbreaker Cylindrical hole Application: external and internal turning Compatibility requires matching holder form and tolerance FAQ What materials is this insert suited for? The DNMG150412 AH8015 Tungaloy turning insert is designed primarily for heat-resistant alloys and general turning applications where balanced wear and edge stability are required. How does the PVD coating help in machining? The PVD-coated surface on this carbide grade reduces adhesive wear and improves temperature resistance, which extends tool life and maintains cutting-edge integrity during continuous operation. Is the insert compatible with standard DNMG holders? Yes. The insert follows ISO geometry; compatibility depends on matching holder form, tolerance class, fixing, size and plate thickness to ensure secure clamping. What is the effect of the 1.2 mm corner radius? A 1.2 mm radius provides a compromise between strength and finish: it increases edge robustness for interrupted cuts while helping to achieve a consistent surface quality on turned parts. Does the chipbreaker support chip control in both roughing and finishing? The double-sided chipbreaker is designed to control chips effectively across common turning operations, aiding safe evacuation and consistent cutting behaviour. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide AH8015, a double-sided chipbreaker and ISO conformity for reliable turning performance and fewer insert changes; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. DNMG 150412 AH8015 Tungaloy – Indexable turning insert, PVD-coated carbide, 55° lead angle The DNMG 150412 AH8015 Tungaloy is an ISO-standard indexable insert designed for external and internal turning of heat‑resistant alloys and general machining applications DNMG 150412 geometry, 55° lead angle PVD-coated carbide AH8015 grade Double-sided chipbreaker for stable chips ISO-standard compatibility with holders Increased productivity on heat‑resistant alloys through balanced wear resistance The combination of a PVD-coated carbide grade and a geometry optimised for durability delivers a predictable cutting life when machining demanding materials. The AH8015 grade provides an even balance between wear resistance and edge stability, which reduces unplanned tool changes and supports higher metal removal rates. For batch production or long runs, this results in a verifiable gain in process efficiency and a lower cost per component, while the indexable insert design enables rapid re‑indexing to restore the cutting edge. Consistent chip control and improved surface quality for fewer rework operations A double-sided chipbreaker paired with the rhombic geometry ensures controlled chip formation and evacuation, which helps to maintain tool stability at elevated cutting speeds. The 55° lead angle combined with a 0° clearance angle promotes a favourable cutting force direction and a reliable surface finish, especially on slender or interrupted turning operations. Predictable chip flow reduces machine downtime and the need for secondary finishing, supporting a stable production route with consistent part tolerances. Straightforward integration into ISO holder systems for rapid setup Built to ISO turning insert standards, the insert’s size, thickness and mounting hole permit direct compatibility with standard external holders and boring bars when the holder’s form, tolerance class and clamping method match. The insert features a cylindrical hole, a 4.76 mm thickness and a 15 mm seat width, with a 1.2 mm corner radius for versatile edge strength. This standardisation simplifies inventory management and shortens setup time on the shop floor, while ensuring secure clamping and repeatable seating in properly specified toolholders. For dependable performance in turning operations, request the DNMG 150412 AH8015 Tungaloy insert via Metav Werkzeuge or contact Metav Werkzeuge’s technical consultants for tailored machining advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6947265 SKU: 6947265-Tungaloy Manufacturer SKU: TUN6947265 Facts Insert size: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Lead angle: 55° Clearance angle: 0° Hole style: cylindrical hole Special features Grade: AH8015 (PVD-coated carbide) Double-sided chipbreaker Rhombic shape ISO series: ISO turning inserts Application: Turning (external and internal) System: insert, matching outer holder or boring bar, support/clamp set and spare screws FAQ What materials is this insert intended for? The DNMG 150412 AH8015 Tungaloy insert is optimised for heat‑resistant alloys and general machining tasks where a balance of wear resistance and edge stability is required. Is the insert reversible or single‑edged? This is a double‑sided indexable insert; both faces can be used, allowing re‑indexing to a fresh cutting edge and extending the usable life of the insert. Which holder type is compatible with this insert? Compatibility follows ISO standards: the insert fits holders and boring bars that match the insert’s form, size, thickness and tolerance class; secure clamping and matching clearance are essential. How does the AH8015 grade affect machining performance? The AH8015 PVD‑coated carbide offers a balanced combination of abrasion resistance and edge stability, improving tool life and process reliability when machining tougher alloys. What chip control can be expected during interrupted cuts? The double‑sided chipbreaker provides stable chip formation and evacuation, which supports controlled cutting forces and reduces the likelihood of built‑up edge during interrupted turning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
Combine PVD-coated carbide wear resistance, a 55° DNMG geometry and a 1.2 mm corner radius to maintain stable cutting edges when machining heat-resistant alloys; order genuine inserts via Metav Werkzeuge or consult our specialists for application support. DNMG150412 AH8015 Tungaloy turning insert — PVD-coated carbide, 55° rhombic geometry A DNMG150412 AH8015 Tungaloy turning insert optimised for external and internal turning of heat‑resistant alloys, offering a balance of wear resistance and edge stability for reliable shop‑floor performance. ISO DNMG geometry, 55° rhombic PVD-coated carbide for heat-resistant alloys 1.2 mm corner radius for stable cutting Double-sided chipbreaker, 4.76 mm thickness Consistent results when machining heat-resistant alloys For applications involving elevated temperatures, the combination of a PVD coating and a carbide substrate provides improved resistance to abrasive and thermal wear while maintaining cutting‑edge integrity. This insert’s design is intended to reduce flank wear and preserve dimensional accuracy over extended tool life, which translates into fewer tool changes and less downtime. The result is a more predictable machining process and improved overall equipment effectiveness. Geometry and form deliver process stability The 55° rhombic geometry with a 1.2 mm corner radius gives a stable contact area and predictable chip formation during turning. The rhombic shape supports a range of approach angles, while the 0° clearance face promotes consistent contact with the workpiece. These features make the insert compatible with standard ISO holders and boring bars when the holder’s form, clearance angle and tolerance class match the insert specifications, ensuring simple integration into existing tool systems. Coating and substrate work together for balanced performance A PVD-coated carbide grade offers a compromise between hardness and toughness that is ideal for general turning of heat‑resistant alloys. The coating enhances surface hardness and reduces built-up edge, while the carbide core provides the necessary edge stability under intermittent loading. Where finish quality and repeatability are required, this combination helps to achieve consistent surface integrity without sacrificing tool life. System compatibility and practical handling The insert is supplied in the ISO DNMG format and is designed to be used with a matching external holder or boring bar, plus the appropriate clamp set and replacement screws for secure fixation. The plate’s cylindrical hole and standard dimensions simplify mounting and replacement in production environments. Selecting the correct chipbreaker variant and grade for the workpiece material and stability level will maximise productivity and process reliability in turning operations. Contact Metav Werkzeuge for tailored application advice and to secure genuine Tungaloy DNMG150412 AH8015 inserts for temperature‑challenging turning tasks; our technical team is available to support selection and compatibility checks. Technical Data Article number: 6947125 Manufacturer SKU: TUN6947125 SKU: 6947125-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Carbide Facts Corner radius: 1.2 mm Insert angle: 55° Plate thickness: 4.76 mm Insert size: 15 Special features PVD coating ISO DNMG series Rhombic shape, 55° geometry Cylindrical hole 0° clearance face Double-sided chipbreaker Suitable for turning of heat‑resistant alloys Compatibility with ISO external holders and boring bars FAQ Which materials is this insert suitable for? This insert is formulated for turning heat‑resistant alloys; the AH8015 grade and PVD coating on the DNMG150412 AH8015 insert give a good balance of wear resistance and edge stability for such materials. What geometry does the insert have and why does it matter? The DNMG150412 AH8015 insert features a 55° rhombic geometry, which provides flexibility in approach angles and contributes to process stability during both external and internal turning. How does the coating affect performance? The PVD coating on the DNMG150412 AH8015 insert increases surface hardness and reduces adhesion, which helps to lower flank wear and maintain consistent cutting performance in demanding turning operations. Is this insert compatible with standard ISO holders? Yes; the DNMG150412 AH8015 insert follows ISO DNMG dimensions and is intended to be used with matching external holders or boring bars when form, free angle and tolerance class are compatible. What is the significance of the 1.2 mm corner radius? A 1.2 mm corner radius on the DNMG150412 AH8015 insert gives enhanced edge strength and helps to distribute cutting forces, improving stability on interrupted cuts and when machining less rigid setups. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
The combination of a PVD-coated carbide AH8015 grade and a 55° rhombic geometry provides a balanced mix of wear resistance and cutting-edge stability for turning heat‑resistant alloys; order the insert directly via Metav Werkzeuge or consult application specialists for holder compatibility. DNMG 150412 AH8015 turning insert — Tungaloy The DNMG150412 AH8015 is an ISO rhombic turning insert for external and internal turning, optimised for machining heat‑resistant alloys. PVD-coated carbide AH8015 55° rhombic geometry for versatile turning 1.2 mm corner radius for robust edges Double-sided chipbreaker with cylindrical hole Durable coating and grade for demanding alloys The combination of PVD coating and carbide substrate in the AH8015 grade is tailored for the general machining of heat‑resistant alloys, offering a reliable compromise between wear resistance and edge stability. A PVD layer reduces abrasive wear and improves adhesion at elevated temperatures, which in turn supports consistent tool life and predictable process windows. The ISO conformity of the insert simplifies integration into established toolholders and aids reproducibility across different machines. Geometry and clamping that enhance process stability A 55° rhombic geometry with a 1.2 mm corner radius delivers mechanical strength at the cutting edge while still permitting versatile approach angles for external and internal operations. The double‑sided chipbreaker design and the cylindrical locating hole contribute to secure seating in compatible holders, reducing vibration and maintaining surface integrity. These geometric features are selected to improve process stability, minimise edge chipping and extend intervals between indexing or replacements. System compatibility and selection guidance An ISO‑standardised insert like this requires a matching holder defined by shape, relief angle, tolerance class, clamping/fastening, size and thickness. Typical system components include the indexable insert itself, an appropriate external holder or boring bar, a shim/clamp set and replacement screws. Selecting the correct chipbreaker and grade for the workpiece material and machining conditions is critical: the AH8015 grade is a practical first choice for a wide range of heat‑resistant alloys where a balance of longevity and edge security is needed. Practical benefits for job shops and production lines For workshops seeking reliable, repeatable performance, the combination of the AH8015 grade and the insert’s rhombic form supports improved component finish and stable tool life, which helps reduce unplanned downtime. The ISO indexing concept and double‑sided construction permit economical use of cutting edges, while the robust geometry reduces the risk of premature failure under interrupted cuts. Together, these factors contribute to higher throughput and predictable process results. Contact Metav Werkzeuge for tailored advice on Tungaloy turning inserts such as the DNMG150412 AH8015; email info@metav-werkzeuge.com or call +49 2822 7131930 for application support and compatibility checks Technical data Article number: 6947216 Manufacturer SKU: TUN6947216 Model series: ISO turning indexable inserts Designation: DNMG150412 Grade: AH8015 Core data Corner radius: 1.2 mm Included angle: 55° Relief angle: 0° Plate thickness: 4.76 mm Plate size: 15 mm Design and features Material: carbide (PVD-coated) Shape: rhombic, double-sided Chipbreaker: double-sided Hole: with cylindrical hole Application: external and internal turning System components: insert, holder/boring bar, shim/clamp set, replacement screws Compatibility: ISO-standardised FAQ What materials is this insert suited for? The DNMG150412 AH8015 indexable insert from Tungaloy is designed primarily for the machining of heat‑resistant alloys; the PVD‑coated carbide grade AH8015 balances wear resistance and cutting‑edge stability for such materials. How is holder compatibility determined? Compatibility depends on the insert shape, relief angle, tolerance class, clamping method, size and thickness; the ISO designation DNMG150412 ensures clarity when matching the insert to a suitable external holder or boring bar. Can the insert be indexed to use multiple edges? Yes, the rhombic, double‑sided design allows rotation to fresh edges as required, improving economy per insert and reducing downtime for replacements. What benefits does the AH8015 grade bring in production? The AH8015 grade offers a practical balance between wear resistance and edge stability, resulting in longer tool life and consistent surface quality in general turning operations on tougher alloys. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
Choose the combination of PVD-coated carbide AH8015 and ISO-standard geometry for a balance of wear resistance and edge stability, delivering consistent turning of heat‑resistant alloys with economical indexable use; order the DNMG150412 AH8015 Tungaloy insert via Metav Werkzeuge or consult our machining specialists for tailored advice. DNMG150412 AH8015 Tungaloy turning insert (ISO DNMG150412, PVD-coated) The DNMG150412 AH8015 Tungaloy insert is an ISO‑standard rhombic, double‑sided turning insert intended for external and internal turning of heat‑resistant alloys and general engineering steels. DNMG150412 ISO-standard rhombic insert PVD-coated carbide AH8015 for heat-resistant alloys Double-sided geometry with 1.2 mm corner radius Cylindrical hole for reliable clamping Proven cutting performance for heat‑resistant alloys The combination of PVD-coated surface and AH8015 grade carbide provides a durable balance between wear resistance and edge stability, especially where temperatures rise during cutting. For shops machining nickel‑based or other heat‑resistant alloys, this means fewer interruptions for insert changes and more consistent part quality. The coating reduces adhesion and abrasive wear, while the substrate maintains a tough cutting edge; as a result, tool life extends under demanding conditions and process reproducibility improves. Precise fit and safe clamping in ISO tool systems Built to ISO dimensions, the insert’s rhombic shape with a 55° orientation and a cylindrical hole ensures predictable seating in compatible holders. Compatibility depends on form, relief angle, tolerance class, fastening and thickness; the zero degree relief listed supports certain stable setups and should be matched to the holder geometry. Clear, standardised interfaces make it straightforward to select a suitable external holder, boring bar or clamping kit, thereby reducing setup time and improving repeatability across machines. Economical handling and process security on the shop floor The double‑sided design and 1.2 mm corner radius deliver both cost efficiency and robust edge behaviour: two usable cutting edges per indexation reduce tooling cost per part, while the radius supports strength at interrupted cuts and helps achieve a regular surface finish. The 4.76 mm plate thickness and 15 mm size contribute to rigidity in the cutting zone. Typical system assembly comprises the ISO insert, a matched outer holder or boring bar, a support plate/clamp set and replacement screws, enabling quick re‑indexing and minimal downtime. Request a machining consultation from Metav Werkzeuge for application support or a tailored supply plan — contact Metav Werkzeuge at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for fast, practice‑oriented advice and delivery options. Technical Data Article number: 6947239 SKU: 6947239-Tungaloy Manufacturer SKU: TUN6947239 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Coating: PVD-beschichtet Data ISO designation: DNMG150412 Size: 15 mm Plate thickness: 4.76 mm Corner radius: 1.2 mm Orientation angle: 55° Relief (clearance) angle: 0° Application: Drehen Special features Rhombic plate form Cylindrical hole (mit Loch) – zylindrisches Loch Double-sided chipbreaker PVD-coated carbide grade AH8015 Compatible with ISO holders, clamps and replacement screws FAQ What materials is this insert suited for? The DNMG150412 AH8015 insert is designed primarily for heat‑resistant alloys and general engineering steels; the AH8015 grade balances wear resistance and edge stability for these materials. How is the insert mounted in a holder? Mounting requires an ISO‑compatible holder that matches the DNMG150412 form, thickness and fastening style; the cylindrical hole ensures secure clamping when used with the correct clamp set and screws. How many usable edges does the insert provide? This is a double‑sided insert, offering two indexable cutting edges to reduce tooling cost and support continuous production. What effect does the 1.2 mm corner radius have on machining? A 1.2 mm corner radius increases edge strength, helps with interrupted cuts and can improve surface finish compared with smaller radii, while influencing achievable corner detail on the workpiece. Is the DNMG150412 AH8015 suitable for internal turning? Yes; the ISO rhombic form and compatibility with matched boring bars make the insert suitable for both external and internal turning operations when installed in an appropriate holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
DNMG 150412 AH8015 Tungaloy-Wendeplatte für Drehen DNMG 150412 AH8015 Tungaloy‑Wendeplatte: Universelle ISO‑genormte Wendeschneidplatte zum Außen‑ und Innendrehen hitzebeständiger Legierungen ISO‑genormte DNMG‑Form, hohe Austauschbarkeit PVD‑beschichtetes Hartmetall, lange Standzeit Doppelseitiger Spanbrecher, vielseitige Einsatzmöglichkeiten Zylindrisches Loch, einfache Befestigung Eckenradius 1.2 mm, präzise Konturtreue Hohe Prozesssicherheit durch Material und Beschichtung Die Wendeschneidplatte basiert auf Hartmetall mit PVD‑Beschichtung, weshalb sie eine ausgewogene Kombination aus Verschleißfestigkeit und Schneidkantenstabilität bietet. Anwender profitieren von konstanter Bearbeitungsqualität bei längeren Standzeiten, weil die Schichtbedingungen die Hitzeaufnahme reduzieren und die Schneidkante stabil halten. Für Betriebe, die hitzebeständige Legierungen zerspanen, bedeutet das weniger Werkzeugwechsel und gleichbleibende Oberflächenqualität. Effiziente Zerspanung und Anwendungsbereiche Für das Drehen von Außen‑ und Innenteilen ist die Platte mit doppelseitigem Spanbrecher ausgelegt, wodurch Spanformung und Wärmeabfuhr optimiert werden. Die Kombination aus Eckenradius 1.2 mm und der rhombischen Plattenform ermöglicht präzise Konturen bei stabilen Schnittbedingungen. Empfohlen ist die Wahl des passenden Spanbrechers und der Sorte je nach Werkstoff und Maschinendynamik, um maximale Produktivität und geringe Ausschussraten zu erzielen. Kompatibilität, Handling und Nutzen im Betrieb Die ISO‑Genorm garantiert Austauschbarkeit zu Haltern, wobei Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke entscheidend sind. Die DNMG150412‑Ausführung mit zylindrischem Loch vereinfacht Montage und Wiederholgenauigkeit beim Drehen. Anwender mit wechselnden Seriengrößen schätzen die wirtschaftliche Bilanz: weniger Rüstzeit, verlässlichere Bearbeitung und planbare Werkzeugkosten dank der langlebigen AH8015‑Sorte. Empfehlung: Vertrauen Sie auf die langlebige Performance der Tungaloy‑Wendeplatte mit PVD‑Beschichtung und kontaktieren Sie bei Fragen die technische Beratung von Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6741664 Marke: Tungaloy Serie: ISO‑Drehwendeschneidplatten Bezeichnung: DNMG150412 Fakten Plattengröße: 15 mm Plattendicke: 4,76 mm Winkel: 55° Eckenradius: 1,2 mm Besonderheiten Material: Hartmetall Sorte: AH8015 Schneidstofftyp: PVD‑beschichtetes Hartmetall (PVD = Physical Vapor Deposition, harte Schicht) Spanbrecher: Doppelseitig Plattenform: Rhombisch Freiwinkel: 0° Befestigung: Mit Loch, zylindrisches Loch SKU Hersteller: TUN6741664 SKU: 6741664‑Tungaloy FAQ Welche Werkstoffe lassen sich mit der DNMG150412 AH8015 bearbeiten? Die DNMG150412 AH8015 Tungaloy‑Wendeplatte ist erste Wahl für hitzebeständige Legierungen und allgemeine Stahl‑ und Legierungsbearbeitung; die AH8015‑Sorte bietet ein ausgewogenes Verhältnis von Verschleißfestigkeit und Kantenstabilität. Ist die Platte zu gängigen ISO‑Haltern kompatibel? Ja, die ISO‑Genorm der DNMG‑Form gewährleistet Kompatibilität zu passenden Außenhaltern und Bohrstangen, wobei Freiwinkel, Toleranzen und Befestigungsart zu prüfen sind. Wie wirkt sich der Eckenradius 1,2 mm auf die Bearbeitung aus? Der Eckenradius 1,2 mm erhöht die Konturtreue und Stabilität der Schneidkante, was zu besseren Oberflächen und geringerer Kerbwirkung bei Serienfertigung führt. Wann ist die AH8015‑Sorte gegenüber härteren Sorten zu bevorzugen? AH8015 eignet sich, wenn eine Balance aus Standzeit und Kantenfestigkeit gefragt ist, insbesondere bei wechselnden Werkstoffen oder eingeschränkter Maschinendynamik. Ist die Montage durch das zylindrische Loch besonders zuverlässig? Das zylindrische Loch ermöglicht sichere und wiederholgenaue Befestigung, was Rüstzeiten reduziert und statische Stabilität am Halter verbessert. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG 150412 AH8015 Wendeplatten - Tungaloy
Benefit from the combination of a PVD-coated AH8015 grade and the ISO rhombic DNMG150412 form for consistent tool life and reliable chip control. Order the insert directly via Metav Werkzeuge or ask our consultants if further machining advice is required. DNMG 150412 AH8015 Tungaloy turning insert — ISO rhombic indexable insert for turning DNMG150412 AH8015 Tungaloy turning insert provides a robust solution for external and internal turning, designed for compatibility with ISO holders and a broad range of heat‑resistant alloys. *PVD-coated carbide grade AH8015 *ISO DNMG150412 rhombic insert *Double-sided chipbreaker for versatility *Cylindrical hole for secure clamping Consistent performance and extended cutting life The PVD-coated AH8015 grade offers an economical balance between wear resistance and edge stability, making it well suited for the general machining of heat‑resistant alloys. The coated cemented carbide substrate maintains cutting edge integrity under elevated temperatures, which reduces the need for frequent index changes and supports uninterrupted production runs. This leads to lower tool consumption and predictable maintenance intervals in mixed‑material workshops. Stable clamping and reliable geometry for accurate turning Thanks to the ISO rhombic DNMG150412 geometry and a cylindrical hole, the insert ensures secure fastening and consistent seat repeatability in standard turning holders. The insert’s 55° approach angle combined with a 1.2 mm corner radius produces a controlled cutting action that improves surface finish while limiting deflection on long projections. The double‑sided configuration doubles the usable edges per insert, increasing operating economy without compromising stability. Application-oriented grade and versatile chip control The AH8015 grade is selected for its suitability in handling heat‑resistant alloys, offering a compromise between toughness and hardness that favours both intermittent and continuous cuts. The double-sided chipbreaker supports effective chip formation across varied feeds, simplifying process setup. For workshops seeking reproducible results, the ISO‑compliant form and standardised dimensions enable rapid integration into existing tool systems and consistent component quality. For technical availability and order processing of Tungaloy AH8015 inserts, contact Metav Werkzeuge for immediate assistance via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 6947189 SKU: 6947189-Tungaloy Manufacturer SKU: TUN6947189 Model series: ISO turning inserts Core measurements Corner radius: 1.2 mm Approach angle: 55° Clearance (freesurface) angle: 0° Thickness: 4.76 mm Plate size: 15 mm Features & applications Material: cemented carbide Coating: PVD Grade: AH8015 Shape: rhombic (DNMG) Hole: cylindrical hole (with hole) Chipbreaker: double-sided Typical use: external and internal turning System composition: ISO insert, matching holder, clamping set and screws FAQ What materials is this insert suited for? The DNMG150412 AH8015 Tungaloy turning insert is optimised for the general machining of heat‑resistant alloys and performs well across a broad range of steels and alloyed materials. How does the AH8015 grade affect tool life? AH8015 combines wear resistance and edge stability; in the DNMG150412 form this leads to consistent tool life under elevated temperatures and reduces the frequency of index changes. Is the insert compatible with standard ISO turning holders? Yes, the ISO‑form DNMG150412 geometry and cylindrical hole ensure compatibility with standard ISO turning holders when form, clearance angle and thickness match the holder specification. Can the insert be used for finishing operations? With a 1.2 mm corner radius and the PVD coating, this insert can achieve improved surface quality in many finishing passes while preserving edge strength. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 AH905 Wendeplatten - Tungaloy
Take advantage of the wear‑resistant AH905 grade and the PVD‑coated carbide construction for stable, repeatable turning results; order the insert directly via Metav Werkzeuge or consult our specialists for application support. DNMG 150412 AH905 indexable insert for ISO turning by Tungaloy — PVD‑coated carbide, rhombic form, 55° cutting angle DNMG150412 AH905 Tungaloy indexable insert designed for ISO‑standard turning applications; compatible with matching holders and clamping systems. PVD‑coated carbide for high wear resistance Double‑sided chipbreaker for predictable chips ISO‑standard geometry for holder compatibility Rhombic form with cylindrical hole for secure clamping Consistent cutting life through PVD‑enhanced carbide chemistry The AH905 grade combines a hard PVD‑coating with a tough carbide substrate to resist flank wear and reduce the risk of edge chipping under varying cutting conditions. This chemistry supports a sharp cutting edge that preserves dimensional accuracy over multiple cuts, which translates into fewer indexings and less operator intervention. For users seeking process stability in general turning, the coating reduces adhesive wear and maintains surface finish quality without sacrificing tool life. Geometry and clamping that protect the process The insert’s ISO‑compliant geometry and rhombic form ensure compatibility with a broad range of external holders and boring bars; compatibility depends on form, relief angle, tolerance class, mounting and size. The 0° relief angle, 55° main cutting angle and 4.76 mm plate thickness create a stable seating and reduced vibration during machining. The cylindrical hole and the defined 1.2 mm corner radius help to position the insert precisely and allow secure clamping, which is essential for reproducible results in serial production. Practical benefits: predictable chips and efficient reindexing Equipped with a double‑sided chipbreaker, this insert delivers controlled chip formation and simplifies chip evacuation for turning operations. The reversible nature of the geometry allows rotation to fresh cutting edges, extending effective tool life and lowering consumable costs. The insert is supplied as part of a system that includes a matching external holder or boring bar, shim/clamping set and spare screws, enabling quick replacements on the shop floor and minimising downtime while maintaining process security. For reliable, process‑secure turning choose the Tungaloy AH905 PVD‑coated indexable insert and contact Metav Werkzeuge for tailored advice or to place an order — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 6859491 Manufacturer SKU: TUN6859491 SKU: 6859491-Tungaloy Brand: Tungaloy Model series: ISO‑Drehwendeschneidplatten Facts ISO designation: 150412 Size: 15 mm Plate thickness: 4.76 mm Corner radius: 1.2 mm Relief angle: 0° Cutting angle: 55° Special features Grade/coating: AH905, PVD‑coated carbide Insert form: rhombic (DNMG) Chipbreaker: double‑sided Hole: with cylindrical hole Application: turning (external and internal) System composition: ISO insert, external holder/boring bar, shim/clamping set, spare screws Designed for sharp cutting edge and process security, wear and chip resistance FAQ Is this insert compatible with standard ISO DNMG holders? Yes. The DNMG150412 AH905 Tungaloy indexable insert follows ISO‑standard dimensions; compatibility with a holder is determined by form, relief angle, tolerance class, mounting, size and thickness. Which machining tasks is this grade intended for? The AH905 grade is a PVD‑coated carbide designed for turning operations where a sharp cutting edge and high process security are required; it is suited to continuous and interrupted cuts that demand wear resistance and chipping control. How does the double‑sided chipbreaker benefit production? The double‑sided chipbreaker on this Tungaloy insert promotes controlled chip formation and simplifies evacuation; the reversible geometry allows presenting fresh edges to extend service life and reduce tooling costs. What does the DNMG150412 designation indicate? The DNMG150412 code denotes the rhombic ISO insert form, nominal size and specific geometry; in this case, the 150412 variant includes the plate dimensions, hole style and a 1.2 mm corner radius suited for general turning. Which components are needed to assemble a working tool system? A complete turning system comprises the ISO insert, an appropriate external holder or boring bar, a shim or clamping set and the corresponding screws; the DNMG150412 AH905 Tungaloy insert is designed to integrate into this system for secure clamping and repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 NS520 Wendeplatten - Tungaloy
Take advantage of the NS520 cermet grade and the ISO‑standard DNMG geometry for reliable finishing and repeatable surface quality; compatibility with existing holders is ensured by matching form, clearance angle and dimensions. Order the DNMG150412 insert via Metav Werkzeuge or contact their consultants for application advice and holder recommendations. DNMG 150412 NS520 – Cermet turning insert for finishing, Tungaloy DNMG150412 NS520 cermet indexable insert designed for finishing and light turning operations in steel ISO DNMG 150412 format, rhombic insert NS520 cermet for finish to light machining Double-sided chipbreaker for consistent chip control 0° clearance angle with cylindrical hole High precision finishing for steel turning with measurable gains The DNMG150412 geometry combined with the NS520 cermet composition targets finishing and light machining where surface quality and dimensional accuracy matter. The cermet grade is formulated for even wear and fine edge stability, which reduces the need for frequent regrinding and supports longer intervals between index changes. In practice this means more consistent part runs and improved process economy when turning steel components. Secure clamping and easy holder matching reduce setup time Compatibility is determined by form, clearance angle, tolerance class, fastening, size and thickness; the rhombic plate form and cylindrical hole provide a stable seating and repeatable orientation in ISO‑compliant holders. The 4.76 mm plate thickness and the specified size simplify selection of a matching outer holder or boring bar, lowering setup risk and saving operator time. Clear dimensional data supports a predictable tool life curve and straightforward integration into existing toolsets. Consistent chip control and improved surface finish A double-sided chipbreaker design promotes reliable chip formation and evacuation during finishing passes, reducing the risk of built‑up edge and improving surface integrity. The 0° clearance angle offers intimate contact with the workpiece for tight tolerances while the rhombic shape supports versatile external and internal turning applications. Explaining the term: a chipbreaker is a feature that guides the metal swarf to curl and break, thus maintaining stable cutting and protecting the cutting edge. Practical selection advice and application focus Select this insert where dimensional stability and a fine surface are priorities: shaft finishing, small‑batch precision components and operations requiring controlled, repeatable wear. The cermet composition and the DNMG geometry together favour operations at moderate cutting speeds where finish and accuracy trump aggressive material removal. For bespoke setups or batch planning, Metav Werkzeuge can advise on holder choices, clamping torque and recommended cutting data to match the intended production flow. For tailored guidance on integrating Tungaloy DNMG150412 NS520 inserts into a production line, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for holder matching and order support. Technical Data Article number: 6803444 Manufacturer SKU: TUN6803444 Seller SKU: 6803444-Tungaloy Model series: ISO‑Drehwendeschneidplatten Data Radius: 1.2 mm Plate size: 15 mm Plate thickness: 4.76 mm Clearance angle: 0° Insert angle: 55° Hole: with cylindrical hole Special features Material: Hartmetall (cermet/coated cermet grade) Grade: NS520 Plate form: rhombic Chipbreaker: double‑sided Typical application: turning FAQ What applications suit this cermet insert best? This DNMG150412 NS520 insert is optimised for finishing and light turning operations in steel, offering stable wear and fine surface results. How does the NS520 grade affect tool life and surface quality? The NS520 cermet grade provides even wear and a robust cutting edge that supports improved surface integrity and longer intervals between index changes in finishing operations. Is the insert compatible with standard ISO DNMG holders? Compatibility depends on matching form, clearance angle, tolerance class, fastening, size and thickness; when those parameters align, the insert fits ISO‑compliant holders as expected. Can this insert be used for internal turning? Yes, the rhombic geometry and the double‑sided chipbreaker allow use in both external and internal turning applications when paired with a suitable boring bar or holder. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 NS9530 Wendeplatten - Tungaloy
Benefit from precision finishing, low cutting forces and reliable edge geometry for consistent surface quality in turning operations; order the DNMG 150412 NS9530 directly via Metav Werkzeuge or consult our advisors if needed. DNMG 150412 NS9530 — ISO turning insert (uncoated cermet) by Tungaloy The DNMG 150412 NS9530 is an ISO rhombic turning insert optimised for finishing steel components in continuous cuts and small depths of cut. ISO rhombic insert for precision finishing Uncoated cermet grade NS9530 for fine surfaces 1.2 mm corner radius for stable edge geometry Double-sided design with cylindrical hole for secure clamping High-quality finishing with reduced cutting forces The NS9530 grade is an uncoated cermet developed for finishing operations in steel, delivering a sharp cutting edge and low cutting forces that help reduce workpiece distortion during delicate passes. For customers seeking consistent surface integrity, the finishing-grade composition supports improved surface roughness and fewer rework passes. The insert is intended for continuous cutting and small depth-of-cut scenarios, where the combination of edge geometry and material properties leads to predictable, repeatable results. Effortless integration into ISO turning systems As an ISO-standard insert, compatibility with a toolholder is determined by form factor, clearance angle, tolerance class, fastening method, size and plate thickness. The rhombic shape, 4.76 mm plate thickness and 15 mm inscribed circle make the insert straightforward to match with common external holders and boring bars. The presence of a cylindrical hole enables secure fixation with standard screws and clamping sets, allowing rapid installation and replacement within existing ISO turning systems. Consistent performance and economical edge life The double-sided construction and 1.2 mm corner radius provide two cutting edges per index, improving tool life economy for finishing tasks. The 0° clearance angle and precise geometry maintain a controlled contact condition between the insert and the workpiece, supporting stable chip formation and reduced tool chatter. These technical properties translate into lower machine downtime, predictable tool-change intervals and a reliable production flow for precision turning. Practical application guidance for machining steel Designed primarily for external and internal turning of steel, the insert works best with finishing parameters: small depths of cut, continuous feeds and stable clamping arrangements. Select a matching chipbreaker and the NS9530 grade according to component material, machining stability and the required surface finish. The recommended system comprises the ISO insert, a suitable external holder or boring bar, an underlay/clamp kit and replacement fixing screws to ensure secure assembly and consistent clamping forces. Contact Metav Werkzeuge for application advice and to request article TUN6944607; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com for tailored recommendations and fast availability Technical Data Article number: 6944607 Manufacturer SKU: TUN6944607 Brand: Tungaloy Model series: ISO turning inserts Category: Turning inserts (Wendeschneidplatten) Measurements & Angles Corner radius: 1.2 mm Inscribed circle: 15 mm Plate thickness: 4.76 mm Included angle: 55° Clearance angle: 0° Design & Special features Uncoated cermet grade NS9530 Cemented carbide body Rhombic plate form Double-sided chipbreaker Cylindrical hole (with hole) Intended use: external and internal turning Compatibility determined by form, clearance, tolerance, fastening, size and thickness FAQ Which materials is this insert suitable for? The DNMG 150412 NS9530 insert is specified as a finishing grade for steel and is best applied where a fine surface finish and low cutting forces are required. Can the insert be used for roughing operations? This NS9530 finishing grade is optimised for finishing and small depths of cut; for heavy roughing, a different chipbreaker and a more wear-resistant grade are recommended. How is the insert fixed in the holder? The insert uses a cylindrical hole and standard clamping screws; secure mounting with the correct underlay and clamp set ensures stable machining. How many cutting edges are available per insert? The double-sided design provides two usable edges per index before reorientation or replacement is necessary. What is the article number and manufacturer SKU for ordering? Article number 6944607 and manufacturer SKU TUN6944607 identify this DNMG 150412 NS9530 insert for procurement and stock control. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precise finishing performance, consistent ISO compatibility and the low cutting forces of an uncoated cermet grade for efficient turning operations; order the insert via Metav Werkzeuge or consult our specialists for application advice. DNMG150412 NS9530 Tungaloy — Turning indexable insert, uncoated cermet, 55° The DNMG150412 NS9530 Tungaloy insert for turning offers a rhombic, ISO‑standard geometry tailored to fine finishing of steel components. ISO rhombic insert, 55° geometry Uncoated cermet NS9530 for finishing 1.2 mm corner radius for fine detail Double-sided insert with cylindrical hole High-precision finishing with low cutting forces The insert delivers a consistent, fine surface finish thanks to the uncoated cermet NS9530 composition and a sharp cutting edge designed for finishing cuts. Cermet substrates combine ceramic hardness with metallic toughness, which reduces built-up edge and produces a superior machined surface on steel while keeping cutting forces low. For continuous cuts and small depths of cut, this results in fewer interruptions, predictable tool life and improved process reliability. The rhombic 55° geometry supports accessible cutting positions and reliable edge engagement. System compatibility and straightforward integration Compatibility with toolholders depends on shape, clearance angle, tolerance class, clamping and plate thickness; the ISO designation simplifies selection for toolroom setups. The insert is part of a complete system: ISO turning insert, matching external holder or boring bar, shim/clamping set and replacement screws. The 4.76 mm plate thickness and standard 15 mm size make it suitable for a wide range of commercial holders, while the cylindrical hole and double‑sided design reduce inventory by providing reversible cutting edges and straightforward indexing. Practical guidance on application and material behaviour For steel finishing applications select the NS9530 finishing grade for stable chip formation and excellent surface quality under continuous cutting. The 1.2 mm corner radius supports dimensional detail without inducing excessive cutting loads. As an uncoated option, the insert performs especially well where edge sharpness and low cutting forces are priorities rather than high thermal resistance; the recommendation is to match feeds and depths to small, continuous cuts for optimal life and finish. When machining less stable setups, prefer a chipbreaker and grade tuned to damping conditions to maintain consistent results. For tailored recommendations based on part geometry or to discuss suitable holders and clamping sets, contact Metav Werkzeuge for application support and fast availability. Technical data Article number: 6733194 Manufacturer SKU: TUN6733194 SKU: 6733194-Tungaloy Model series: ISO‑Drehwendeschneidplatten Material: Hartmetall Designation: DNMG150412 Grade: NS9530 Facts Corner radius: 1.2 mm Plate thickness: 4.76 mm Plate size: 15 mm Insert geometry angle: 55° Hole: with hole Hole style: cylindrical Special features Uncoated cermet grade NS9530 Rhombic plate form Double‑sided chipbreaker ISO‑standard turning insert Suitable for finishing of steel System components: insert, holder, shim/clamp, screws FAQ What applications suit this insert best? The DNMG150412 NS9530 Tungaloy insert is intended for external and internal turning, especially finishing of steel with continuous cuts and small depths of cut. How does the NS9530 cermet grade affect performance? The NS9530 cermet provides a sharp cutting edge and low cutting forces, improving surface finish and enabling stable finishing operations on steel. Which holder features are required for compatibility? Compatibility is determined by insert form, clearance angle, tolerance class, clamping method, size and thickness; use ISO‑compliant holders designed for DNMG inserts. Is the insert indexable and reversible? Yes, the double‑sided design with a cylindrical hole allows indexing to a second cutting edge to extend usable life. Can this insert be used for interrupted cuts? The insert is optimised for continuous finishing cuts; for heavily interrupted cuts choose a grade and chipbreaker designed for robustness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 NS9530 Wendeplatten - Tungaloy
Combining the NS9530 uncoated cermet grade with the ISO DNMG form and a 1.2 mm corner radius delivers low cutting forces and a consistently high surface finish in finishing turns; order the Tungaloy DNMG150412 through Metav Werkzeuge or consult our team for application-specific guidance. DNMG 150412 NS9530 – Tungaloy indexable insert for turning, finishing-grade cermet The DNMG 150412 NS9530 is an ISO-standard rhombic indexable insert designed for finishing operations in turning, optimised for continuous cuts and small depths of cut. Finishing-grade uncoated cermet NS9530 ISO-standard DNMG shape, 55° cutting angle 1.2 mm corner radius for fine surface finish Double-sided insert with central hole Optimised finishing performance with reduced cutting forces The NS9530 grade is an uncoated cermet formulated for finishing steel, offering a sharp cutting edge that lowers cutting forces and improves surface quality. Cermet combines ceramic hardness with metallic toughness; this means the cutting edge remains stable during continuous cuts, while wear is predictable and even. With a 1.2 mm corner radius, the insert is suited to produce a refined surface without excessive tool pressure, making it appropriate for tight tolerance external and internal turning where a premium finish is required. Reliable fit and secure clamping for consistent results Built to ISO dimensions, the DNMG geometry guarantees predictable compatibility with appropriate holders and boring bars. The 55° rhombic form and central cylindrical hole ensure positive location and stable clamping, while the plate thickness of 4.76 mm supports rigidity during machining. Because compatibility depends on form, clearance angle, tolerance class, fastening and size, selecting the matching holder and torque for the clamping screw is essential; when correctly mounted, vibration is minimised and repeatable part quality is achieved. Productive finishing cycles with easy indexing and chip control The double-sided design provides two usable cutting edges per face, enabling economical edge changes and steady process behaviour. The integrated double-sided chipbreaker is optimised for continuous cutting conditions and small depths of cut, helping to control chip shape and evacuation without disturbing the workpiece finish. The combination of the NS9530 grade and the DNMG form supports longer edge life in finishing tasks, reducing downtime for edge changes and promoting process stability in production runs. For precision finishing in steel applications, request the Tungaloy DNMG150412 NS9530 from Metav Werkzeuge or contact our consultants at Metav Werkzeuge for tailored cutting data and order support – eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Manufacturer article number: 6998174 SKU: 6998174-Tungaloy Manufacturer SKU: TUN6998174 Model series: ISO indexable turning inserts Data Thickness: 4.76 mm Size: 15 mm Cutting angle: 55° Corner radius: 1.2 mm Special features Grade: NS9530 (uncoated cermet) Double-sided chipbreaker Rhombic shape, cylindrical hole Application: Turning; finishing steel FAQ Which materials is this insert best suited for? The DNMG150412 NS9530 insert is a finishing-grade cermet optimised for steel; it performs best in continuous-turning operations and small depths of cut where surface quality is paramount. How is the insert secured in the holder? Compatibility relies on ISO DNMG form and the holder design; the insert features a central cylindrical hole for positive location and clamping with the appropriate screw and seat to ensure stable cutting. Can the insert be indexed to extend tool life? Yes, the double-sided design provides multiple usable edges; the insert can be rotated or flipped to use alternate cutting edges, supporting economical edge changes in production. What surface finish can be expected with this grade? With the NS9530 cermet and a 1.2 mm corner radius, the insert is engineered to deliver a fine surface finish in finishing passes, reducing the need for additional finishing operations. Is the insert suitable for internal as well as external turning? The ISO DNMG form and the sharp cermet edge make the insert suitable for both external and internal turning tasks, provided the correct holder and cutting parameters are used. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of an uncoated cermet cutting material, a sharp cutting edge for superior surface finish and a compact ISO rhombic geometry for reliable finishing of steel components; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. DNMG150412 NS9530 turning insert — ISO rhombic finishing grade by Tungaloy The DNMG150412 NS9530 is an ISO rhombic turning insert intended for finishing operations on steel, offering a sharp cutting edge, low cutting forces and excellent surface quality. ISO rhombic geometry, 55° cutting angle Uncoated cermet grade NS9530 for finishing Sharp cutting edge for high surface finish Double-sided insert with cylindrical hole Achieve consistent finishing results with low cutting forces The insert is engineered as an uncoated cermet grade optimised for finishing steel, delivering a sharp cutting edge and low cutting forces that reduce vibration and promote dimensional stability. These properties make the component particularly suitable for continuous cutting and small depth-of-cut operations, where surface quality and repeatability are critical. The reduced cutting resistance helps to extend tool life on light interruptions and supports predictable process windows in high-volume turning applications. Compatibility and system setup for reliable clamping Compatibility with the workholder is determined by the insert's form, clearance angle, tolerance class, fastening method, overall size and thickness. The ISO rhombic form with a 55° main angle enables access to turned profiles while the cylindrical locating hole supports positive seating and repeatable clamping. For a complete system, pair the insert with a suitable external holder or boring bar, plus the recommended shim/fastening set and replacement screws; correct matching ensures process stability and the best surface results. Practical guidance for application and benefits at a glance Choose this finishing grade when the priority is superior surface finish and low cutting forces rather than heavy metal removal. The double-sided design offers economical indexability, and the fine edge geometry reduces the need for secondary dressing. When machining steel with stable setups and modest feeds, expect improved part finish and consistent tolerances. For operators new to cermet grades: cermet combines ceramic and metallic phases to offer wear resistance with a fine edge, making it particularly effective in precision finishing tasks. Contact Metav Werkzeuge for tailored advice on using the DNMG150412 NS9530 finishing insert in specific turning processes — email info@metav-werkzeuge.com or call +49 2822 7131930 for rapid consultation Technical data Article number: 6944660 Manufacturer item number: 6944660 SKU: 6944660-Tungaloy Manufacturer SKU: TUN6944660 Numbers / Core technical data ISO designation: 150412 Cutting angle: 55° Corner radius: 1.2 mm Plate thickness: 4.76 mm Plate size: 15 mm Clearance angle: 0° Hole: with hole (cylindrical hole) Chipbreaker: double-sided Designs / Special features Model series: ISO turning indexable inserts Grade: NS9530 (uncoated cermet) Application: turning, finishing on steel Insert form: rhombic, DNMG configuration System: insert, matching external holder/boring bar, shim and screws ensure compatibility FAQ What materials is this insert intended for? The NS9530 finishing grade is specified for machining steel, where the DNMG150412 NS9530 Tungaloy turning insert yields low cutting forces and high surface quality. Is the insert indexable on both sides? Yes, the insert is double-sided; both cutting edges can be used before reindexing, improving economical usage. How does the cermet grade affect surface finish? Cermet materials offer a fine, wear-resistant edge; the NS9530 grade is tuned for high surface finish in finishing cuts under continuous cutting conditions. Which holders are compatible with this ISO insert? Compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness; the DNMG shape requires a matching rhombic external holder or boring bar with suitable screw/clamp geometry. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 NS9530 Wendeplatten - Tungaloy
Benefit from the combination of precise finishing performance and reliable ISO compatibility: the uncoated NS9530 cermet grade delivers a sharp cutting edge and low cutting forces for consistently superior surface finish, while the ISO dimensions ensure straightforward holder compatibility. Order directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. DNMG 150412 NS9530 indexable turning insert by Tungaloy — rhombic 55° geometry, uncoated cermet DNMG150412 NS9530 Tungaloy-Wendeplatte is an ISO-format indexable turning insert designed for finishing operations in turning, optimised for continuous cuts and fine surface quality ISO 55° rhombic geometry Uncoated cermet NS9530 Corner radius 1.2 mm Double-sided chipbreaker Precision finishing with lower cutting forces The DNMG150412 NS9530 Tungaloy insert is designed as a finishing grade, where a sharp cutting edge and low cutting forces are decisive for achieving consistent part quality. The uncoated cermet composition emphasises edge stability and wear resistance during light cuts, which reduces vibration and supports a superior surface finish on steels. As a consequence, setups for continuous turning cycles benefit from predictable tool life and reduced need for rework, which improves throughput without sacrificing accuracy. ISO compatibility that simplifies tooling decisions This insert follows the ISO turning insert standards, so compatibility with holders is determined by form, clearance angle, tolerance class, fastening and plate thickness. The rhombic 55° geometry and the specified plate dimensions make it suitable for a wide range of external and internal turning applications when paired with the correct toolholder or boring bar. The integrated features—such as the cylindrical central hole and double-sided design—allow for two usable cutting edges per side, improving economy and minimising downtime during index changes. Application-focused design for finishing steels Engineered as a finishing grade for steel, the NS9530 formulation provides a balance between edge sharpness and wear resistance that is especially effective with small depths of cut and continuous feeds. The corner radius 1.2 mm supports improved part profile integrity while limiting edge chipping in light-interruption conditions. When combined with the appropriate chipbreaker geometry and machining parameters, this insert contributes to reduced feed marks and consistent dimensional results, making it a reliable choice for precision turning tasks. Contact Metav Werkzeuge for tailored recommendations on tooling and availability of the Tungaloy DNMG150412 NS9530 indexable insert — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitable holders and delivery options Technical data Article number: 6944589 Manufacturer SKU: TUN6944589 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts Corner radius: 1.2 mm Plate thickness: 4.76 mm Plate size: 15 mm Geometry angle: 55° Clearance angle: 0° Special features ISO designation: DNMG150412 Grade: NS9530 (uncoated cermet) Double-sided chipbreaker Rhombic plate shape With cylindrical hole for secure clamping Intended application: turning; suitable for external and internal operations System components: ISO insert, compatible outer holder or boring bar, shim/clamp set and replacement screws FAQ What materials is this insert intended for? The NS9530 grade is formulated as a finishing grade primarily for machining steel; the DNMG150412 insert offers a sharp cutting edge and is optimised for continuous cuts on steel workpieces. Can the insert be indexed to use multiple cutting edges? Yes. The DNMG150412 is double-sided with a central cylindrical hole, allowing indexing to additional edges and improving tool economy. Which holder types are compatible with this ISO insert? Compatibility is determined by the insert form, clearance angle, tolerance class, fastening method, size and thickness; the DNMG150412 conforms to ISO turning insert standards and fits matching rhombic 55° holders and boring bars. Does the uncoated cermet grade affect cutting parameters? Uncoated cermet grades such as NS9530 favour finishing feeds and lower cutting forces; parameters should be adjusted for light depths of cut to exploit the grade’s edge stability and achieve the best surface finish. What operational benefits does the 1.2 mm corner radius provide? A corner radius of 1.2 mm improves profile strength and reduces the risk of edge chipping during finishing passes, supporting consistent dimensional accuracy and improved surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T505 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide performance, precise DNMG geometry and reliable chip control for efficient cast‑iron turning; order directly via Metav Werkzeuge or consult the technical advisors for application support. DNMG 150412 T505 turning indexable insert by Tungaloy The DNMG150412 T505 Tungaloy insert is an ISO‑standard, rhombic indexable insert developed for economical and stable turning of cast iron, offering reliable chip control and consistent tool life in production environments. CVD-coated T505 grade for economical machining Suited for cast iron turning operations Rhombic DNMG geometry, 55° cutting angle Double-sided chipbreaker, 1.2 mm corner radius Consistent machining performance for cast iron turning The combination of a CVD-coated surface and a wear‑resistant carbide substrate in the T505 grade delivers measurable endurance when machining cast iron, reducing insert changes and downtime. The rhombic geometry with a 55° included angle provides a stable cutting edge that resists vibration in less rigid set‑ups, while the double‑sided chipbreaker improves chip form and evacuation. This results in steadier surface finish and extended tool life, which supports predictable cycle times and reduced process variability. Secure seating and compatibility ensure reliable production cycles The ISO‑format design of the insert ensures compatibility with standard DNMG holders when matched by form, tolerance class, fastening method, size and thickness. The cylindrical hole and nominal thickness of 4.76 mm allow secure clamping and accurate repeatability across index changes, supporting uninterrupted production. Clear specification and standardisation simplify tooling logistics: replacement inserts maintain the same datum points, which reduces set‑up time and preserves machining parameters from one index to the next. Productivity gains through optimised chip control and geometry With a 1.2 mm corner radius and a tailored chipbreaker geometry, this insert is tuned for interrupted and continuous cuts commonly encountered in turning cast iron components. The chip former minimises re‑cutting and helps to prevent chip entanglement on long parts, enhancing operator safety and machine uptime. When paired with appropriate cutting parameters, the insert’s T505 formulation delivers a favourable cost‑per‑component ratio by balancing wear resistance with economical edge life. Practical guidance for integration into the shop floor Select a matching DNMG‑type external holder with suitable rigidity and clamping torque to exploit the insert’s strengths. For roughing passes where higher material removal is required, opt for slightly reduced cutting speeds and increased feed to maintain chip control; for finishing, the combination of CVD coating and rhombic geometry supports improved surface quality. The insert’s ISO conformity simplifies matching across toolholders and makes stocking and rotation straightforward for production‑oriented workshops. Contact Metav Werkzeuge for tailored advice on clamping solutions and to arrange supply of the DNMG150412 T505 insert from Tungaloy through our consultants Technical data Article number: 6831240 SKU: 6831240-Tungaloy Manufacturer SKU: TUN6831240 Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Corner radius: 1.2 mm Included angle: 55° Thickness: 4.76 mm Inscribed circle/size: 15 mm Free clearance (relief angle): 0° Special features ISO‑standard DNMG150412 rhombic insert T505 CVD‑coated carbide grade Double‑sided chipbreaker Cylindrical hole for secure clamping Suitable for turning applications, optimised for cast iron FAQ What materials is this insert best suited to machine? The DNMG150412 T505 insert is formulated for cast iron machining; the T505 CVD coating and carbide substrate are balanced to provide economical performance on grey and nodular cast irons. Which holders are compatible with this insert? Compatibility depends on holder form, tolerance class, clamping method, size and thickness; ISO‑compliant DNMG external holders designed for a 15 mm inscribed circle and 4.76 mm thickness are appropriate for the DNMG150412 T505 insert. How does the chipbreaker design affect cutting results? The double‑sided chipbreaker promotes controlled chip formation and evacuation, reducing re‑cutting and improving surface finish during both continuous and interrupted turning operations. How many usable cutting edges are available per insert? As a double‑sided DNMG insert, it provides multiple indexable edges; the exact number of edges depends on the insert geometry and indexing routine specified by the toolplan. Is the insert suitable for interrupted cuts? Yes — the combination of the T505 grade and the rhombic geometry gives good edge stability for interrupted turning, provided the holder and set‑up offer sufficient rigidity. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
DNMG 150412 T505 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide grade T505, precise 55° geometry and a 1.2 mm corner radius for consistent, economical cast-iron turning; order directly via Metav Werkzeuge or contact our technical advisors for compatibility checks. DNMG150412 T505 rhombic turning insert, 55°; Tungaloy The DNMG150412 T505 is an ISO-standard rhombic indexable insert designed for efficient external and internal turning, optimised for economic cast-iron machining and compatible with standard external holders and boring bars ISO‑standard rhombic insert, 55° cutting angle CVD-coated carbide grade T505 for cast iron Double-sided chipbreaker, cylindrical hole design 1.2 mm corner radius, plate thickness 4.76 mm Productivity through optimised grade and geometry The insert is manufactured from carbide with a CVD-coated surface in grade T505, which is tuned for the economic machining of cast iron. This combination delivers stable cutting behaviour and extended tool life in serial production. The 55° cutting angle in the rhombic geometry reduces radial cutting forces, enabling predictable chip formation and consistent dimensional results—benefits that reduce downtime and support throughput in turning operations. Reliability and fit for purpose in the tool system Compatibility is governed by insert shape, clearance angle, tolerance class, fixing, size and thickness. The DNMG150412 T505 features a cylindrical hole and standard form that ensures secure clamping in appropriate external holders or boring bars. The double-sided design offers two indexable cutting edges per side, which supports economical use and quick edge changes. Clear indications of plate size and thickness assist in selecting the correct clamping and replacement hardware for reliable performance. Controlled chipbreaking and application guidance A double-sided chipbreaker tailored to cast-iron applications helps to control chips during interrupted and continuous cuts, improving surface finish and evacuation from the cutting zone. The 1.2 mm corner radius provides a balance between edge strength and feed flexibility, making the insert suitable for finishing and light roughing passes where edge stability and surface integrity are priorities. Select holder rigidity and cutting parameters according to part stability to fully exploit the insert’s productive potential. For reliable, economical cast-iron turning with Tungaloy quality, request availability and technical guidance from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to confirm fitment and delivery options Technical data Article number: 6831312 SKU: 6831312-Tungaloy Manufacturer SKU: TUN6831312 Model series: ISO‑Drehwendeschneidplatten Facts Corner radius: 1.2 mm Cutting angle: 55° Plate thickness: 4.76 mm Plate size: 15 mm Special features Rhombic plate form (DNMG) CVD-coated carbide, grade T505 Double-sided chipbreaker Cylindrical hole (with hole) ISO standard for turning applications FAQ What materials is this insert designed for? The DNMG150412 T505 insert is designed primarily for machining cast iron; the T505 grade and chipbreaker are optimised for economical cast-iron turning. Can the insert be used in internal turning applications? Yes, the rhombic geometry and standard ISO form permit use in suitable boring bars for internal turning as well as external turning. How does the 1.2 mm corner radius affect cutting? A 1.2 mm corner radius increases edge strength for light roughing and finishing, improving robustness and surface quality during turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5105 Wendeplatten - Tungaloy
Combine the T5105 CVD-coated carbide for enhanced wear resistance with the 55° rhombic geometry for stable chip control during high-speed turning of cast iron; order the DNMG150412 directly via Metav Werkzeuge or consult Metav Werkzeuge’s specialists for holder compatibility. DNMG 150412 T5105 DNMG Turning Insert — CVD-coated carbide, 55° — Tungaloy DNMG150412 T5105 is an ISO-standard rhombic insert designed for high-speed external and internal turning, optimised for stable machining of cast iron under controlled conditions CVD-coated carbide for high wear resistance Rhombic 55° geometry for versatile turning Double-sided chipbreaker for extended tool life Cylindrical hole for secure clamping Reliable performance for high-speed turning of cast iron The T5105 grade is a CVD-coated carbide developed for wear resistance in high-speed applications. In practice, the coating reduces flank and crater wear so that production runs remain consistent and predictable; this means fewer unexpected tool changes and more stable cycle times. The insert’s substrate delivers toughness, while the coating maintains edge integrity during continuous cutting, which is particularly beneficial when machining cast materials under steady setups. ISO compatibility and secure mounting reduce setup time Manufactured to ISO dimensions, the insert ensures compatibility with standard holders when form, relief angle, tolerance class, attachment method, size and thickness match the toolholder. The cylindrical hole facilitates positive clamping and repeatable seating, allowing clamping forces to be transmitted securely. This compatibility avoids costly guessing during tool changeovers and supports a system approach comprising an insert, matching outer holder or boring bar, seating pad and fasteners. Geometry and chip control for consistent finishes The rhombic 55° geometry combines accessibility for external and internal turning with favourable cutting-edge engagement. The integrated double-sided chipbreaker is engineered to create short, controllable chips, improving surface finish and reducing the risk of chip entanglement in enclosed operations. For applications that demand consistent part quality, this geometry supports reliable surface integrity with minimal secondary operations. Practical system considerations and selection guidance A productive cutting system comprises the insert, a compatible outer holder or boring bar, an appropriate seating pad or clamp kit, and spare screws. The 4.76 mm thickness and 15 mm size contribute to stable clamping in most standard ISO toolholders, while the 1.2 mm corner radius balances edge strength with achievable surface finish. Select the chipbreaker and grade to match the workpiece, machining mode and rigidity of the setup to obtain the best life and productivity. Contact Metav Werkzeuge to confirm holder compatibility and grade selection for specific cast-iron turning tasks; email info@metav-werkzeuge.com or call +49 2822 7131930 to request technical advice or ordering information. Technical data Article number: 6850203 SKU: 6850203-Tungaloy Manufacturer SKU: TUN6850203 Material: Carbide Model series: ISO turning inserts Application: Turning Facts Size: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Geometry angle: 55° Relief angle: 0° Special features Grade/coating: T5105 (CVD-coated) Hole: with hole, cylindrical hole Shape: rhombic Chipbreaker: double-sided Compatible with ISO holders FAQ What materials is this insert suitable for? The Tungaloy DNMG150412 in grade T5105 is intended primarily for cast-iron machining; the grade’s CVD coating and substrate provide wear resistance suited to high-speed turning of cast materials. How does the insert mount in the holder? The insert is ISO-standard and features a cylindrical hole for secure clamping; compatibility depends on holder form, relief angle, tolerance class, attachment method, size and thickness. What benefit does the 55° rhombic geometry provide? The 55° rhombic geometry offers versatility for external and internal turning, facilitating access and controllable cutting engagement, while supporting predictable chip formation with the double-sided chipbreaker. Is the DNMG150412 suitable for finishing passes? With a 1.2 mm corner radius and the combination of substrate and T5105 coating, the insert can achieve consistent surface finishes when used in appropriately rigid setups and correctly selected cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5105 Wendeplatten - Tungaloy
DNMG 150412 T5105 Wendeplatte für Drehen von Tungaloy DNMG150412 T5105 bietet eine verschleißfeste Lösung für produktives Drehen von Gusseisen unter stabilen Bearbeitungsbedingungen ISO-genormte rhombische Platte, 15 mm CVD-beschichtetes Hartmetall: hohe Verschleißfestigkeit Doppelseitiger Spanbrecher für längere Standzeit Zylindrisches Loch für sichere Befestigung Eckenradius 1,2 mm für gute Oberflächengüte Hohe Produktivität durch verschleißfesten Schneidstoff Die CVD-beschichtete Hartmetall-Sorte T5105 ist speziell für die Hochgeschwindigkeitsbearbeitung von Gusseisen ausgelegt. Durch die Kombination aus verschleißfester Beschichtung und robustem Grundmetall wird die Werkzeugstandzeit erhöht, was Rüst- und Stillstandszeiten reduziert. Das Ergebnis ist eine konstante Zerspanungsleistung und eine verbesserte Wirtschaftlichkeit in Serienfertigung und Werkzeugbau. Präzise Wechselbarkeit und Systemkompatibilität Als Teil der ISO-Drehwendeschneidplatten ist die Platte auf standardisierte Haltersysteme ausgelegt; die Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Die Ausführung mit zylindrischem Loch ermöglicht eine sichere Befestigung in Außenhaltern und Bohrstangen, sodass ein schneller und reproduzierbarer Plattenwechsel möglich ist und Rüstzeiten minimiert werden. Formgebung für Oberflächengüte und Wirtschaftlichkeit Die rhombische Plattenform mit einem Winkel von 55° und einem Eckenradius von 1,2 mm sorgt für eine stabile Schneidkante und feine Oberflächenergebnisse. Die doppelseitige Ausführung erlaubt das Wenden der Platte und verdoppelt damit die nutzbare Schnittkante, was die Stückkosten pro Kante senkt und die Prozesssicherheit erhöht. Empfohlene Anwendung und Zielgruppe Die Wendeplatte eignet sich besonders für Produktionsbetriebe und Lohnfertiger, die Außen- und Innendrehen von Gusseisen bei stabilen Aufspannbedingungen durchführen. Bei der Auswahl des passenden Spanbrechers und der Sorte empfiehlt sich die Abstimmung auf Werkstoff, Bearbeitungsart und Maschinensteifigkeit, um optimale Ergebnisse und lange Standzeiten zu erzielen. Empfehlung: Für produktive Hochgeschwindigkeitszerspanung die Tungaloy-Wendeplatte einsetzen; technische Fragen und Bestellwünsche an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 richten Produktmerkmale Artikelnummer: 6850205 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: DNMG150412 Hersteller-SKU: TUN6850205 Fakten Eckenradius: 1,2 mm Winkel: 55° Plattendicke: 4,76 mm Plattengröße: 15 mm Besonderheiten Material: Hartmetall Beschichtung: T5105 (CVD, Chemische Dampfabscheidung) – verschleißfest für Hochgeschwindigkeit Plattenform: rhombisch Loch: mit Loch (zylindrisches Loch) Spanbrecher: doppelseitig Schneidstofftyp: CVD-beschichtetes Hartmetall Anwendung: Drehen Einsatzgebiet: Gusseisen bei stabilen Bedingungen Systemaufbau: ISO-Drehplatte, passender Außenhalter oder Bohrstange, Unterlage/Klemmsatz und Ersatzschrauben FAQ Welche Werkstoffe sind mit der DNMG150412 T5105 Wendeplatte bearbeitbar? Die DNMG150412 T5105 von Tungaloy ist für die Hochgeschwindigkeitsbearbeitung von Gusseisen optimiert; in der Praxis erzielt die Platte bei stabiler Aufspannung und angepassten Schnittwerten die beste Performance. Wie viele Schneidkanten stehen pro Platte zur Verfügung? Die rhombische Ausführung mit doppelseitigem Spanbrecher bietet mehrere verwertbare Schneidkanten; durch Wenden lässt sich die Nutzungsdauer erheblich verlängern. Welches Eckenradius ist ideal für feine Oberflächen mit dieser Platte? Mit einem Eckenradius von 1,2 mm eignet sich die Platte besonders für Anwendungen, die eine gute Oberflächengüte bei mittleren bis hohen Schnittwerten erfordern. Sind spezielle Halter für die DNMG150412 erforderlich? Die Platte ist ISO-genormt; die Kompatibilität hängt von Form, Freiwinkel, Befestigung und Dicke ab. Für sichere Montage empfiehlt sich ein geeigneter Außenhalter oder eine Bohrstange im ISO-System. Wie wirkt sich die T5105-Beschichtung auf die Standzeit aus? Die CVD-Beschichtung T5105 erhöht die Verschleißfestigkeit und trägt zu stabileren Standzeiten bei, insbesondere bei hohen Schnittgeschwindigkeiten in Gusseisen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG 150412 T5105 Wendeplatten - Tungaloy
Benefit from the combination of high-speed performance, a durable CVD-coated cemented carbide grade and a precise 1.2 mm corner radius to ensure consistent, long-lasting turning results; order the insert directly via Metav Werkzeuge or consult our specialists for holder compatibility and application advice. DNMG 150412 T5105 Turning Insert by Tungaloy A DNMG150412 T5105 turning insert for ISO-standard external and internal turning, optimised for high-speed machining of cast iron under stable conditions. ISO rhombic insert DNMG150412 CVD-coated cemented carbide T5105 Double-sided chipbreaker for stable cuts Cylindrical hole and 0° clearance angle High-speed cast-iron performance with controlled wear The CVD-coated cemented carbide grade T5105 is developed for high-speed turning of cast iron where stability and predictable tool life are essential. The CVD-coated layer improves wear resistance by forming a hard, thermally stable barrier between the cutting edge and abrasive workpiece material, which reduces flank wear and extends effective machining time. For production environments that prioritise uptime and repeatable surface finish, this grade provides a measured balance between edge stability and toughness, making it a rational choice for operations seeking lower tooling costs per component. Reliable clamping and ISO compatibility for straightforward integration The insert follows ISO geometry for rhombic indexable plates, so compatibility with holders is determined by form, free angle, tolerance class, fastening, size and thickness. The plate features a cylindrical hole, a double-sided chipbreaker and a 0° clearance configuration with an included angle of 55°, creating a secure seating and predictable rake behaviour in a matched holder. These mechanical design choices reduce setup time and simplify index changes: once the correct external holder or boring bar and clamping set are selected, the plate can be rotated to present a fresh cutting edge without altering cutter-body geometry, supporting uninterrupted production routines. Improved chip control and consistent surface quality A 1.2 mm corner radius increases edge strength and helps maintain dimensional stability during interrupted cuts or when machining irregular cast-iron surfaces. The double-sided chipbreaker promotes reliable chip formation and evacuation at the speeds this grade is designed for, which reduces the risk of built-up edge and thermal damage to the cutting edge. With a plate thickness of 4.76 mm and a nominal size of 15 mm, this insert provides the rigidity required for stable external and internal turning while still allowing multiple indexes per plate, improving cost-efficiency. Specifying the correct chipbreaker and grade for the application leads to fewer tool changes and a higher first-pass yield. For assured high-speed cast-iron turning with the Tungaloy T5105 grade, contact Metav Werkzeuge for stock information and holder compatibility checks via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best setup for the production task at hand Technical data Article number: 6852968 SKU: 6852968-Tungaloy Manufacturer SKU: TUN6852968 Brand: Tungaloy Model series: ISO turning indexable inserts Core specifications Size: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Included angle: 55° Clearance angle: 0° Design and special features Shape: rhombic Hole: with cylindrical hole Chipbreaker: double-sided Material: cemented carbide Coating / grade: CVD-coated T5105 Application: turning (external and internal) FAQ Which materials is this insert intended for? The DNMG150412 T5105 Tungaloy insert (SKU 6852968-Tungaloy) is intended primarily for high-speed machining of cast iron under stable cutting conditions, with the grade optimised for abrasive, hard microstructures. What does the 1.2 mm corner radius mean for component finish? A corner radius of 1.2 mm on the DNMG150412 T5105 insert increases edge strength and improves dimensional stability, helping to deliver consistent surface quality while resisting chipping on interrupted cuts. Is the plate indexable and how many usable edges does it offer? Yes, the DNMG150412 plate is double-sided with a chipbreaker on each side; the design allows rotation to fresh cutting edges, which extends the usable life of each plate and reduces tooling change frequency. Which holder types are compatible with this ISO plate? Compatibility depends on matching holder form, free angle, tolerance class, fastening, size and thickness; the insert conforms to ISO DNMG geometry, so suitable ISO external holders or boring bars with the correct pocket and clamping system are required. Can this insert be used for internal turning as well as external turning? Yes, the DNMG150412 T5105 Tungaloy insert is suitable for both external and internal turning operations, provided the holder and process parameters are adapted to the specific machining situation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide grade T5115, consistent edge stability and ISO compatibility to reduce changeovers and maintain steady turning performance; order directly via Metav Werkzeuge or consult our technical team for application-specific advice. DNMG 150412 T5115 indexable insert for Turning — Tungaloy DNMG 150412 T5115 is an ISO-format indexable turning insert designed for external and internal turning of cast iron, offering a CVD-coated carbide grade for balanced wear resistance and cutting-edge stability. DNMG 150412 geometry, ISO standard CVD-coated carbide grade T5115 Double-sided chipbreaker for stability Rhombic 55° insert with 1.2 mm radius Reliable wear resistance for cast-iron turning The CVD-coated carbide grade T5115 is formulated as a universal solution for machining cast iron, providing a controlled compromise between wear resistance and cutting-edge robustness. This balance extends tool life and lowers the frequency of insert changes, which in turn supports higher machine utilisation and fewer production interruptions. Where surface quality and repeatable performance are priorities, the combination of a stable cutting edge and protective coating helps to maintain dimensional consistency across batches. Predictable chip control and process stability The rhombic shape with a 55° cutting edge and a 1.2 mm corner radius, combined with a double-sided chipbreaker, promotes reliable chip control during both external and internal turning operations. The insert’s relief angle 0° and the presence of a cylindrical mounting hole ensure repeatable seating and clamping in ISO-compatible toolholders; as a result, cutting forces remain predictable and vibration is reduced. These geometric features translate into improved surface finish and reduced scrap rates for routine turning tasks. Seamless integration and practical machining benefits Belonging to the ISO indexable turning insert series, this format allows straightforward replacement in standard holders and simplifies inventory management for production shops. The inscribed circle 15 mm and thickness 4.76 mm conform to common holder interfaces, enabling quick tooling swaps and predictable set-ups. The CVD coating forms a hard, wear-resistant layer deposited on the carbide substrate, which lowers abrasion and chemical wear during cutting; in practice, this means fewer tool interventions and a more economical machining cycle. For applications requiring tailored cutting parameters or further optimisation, technical consultation is recommended to match grade and chipbreaker to material, machining strategy and machine stability. For cast-iron turning projects requiring consistent edge life and process reliability, contact Metav Werkzeuge for specification support and availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6852969 Manufacturer SKU: TUN6852969 Internal SKU: 6852969-Tungaloy Manufacturer: Tungaloy Facts Inscribed circle: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Cutting edge angle: 55° Relief angle: 0° Special features Shape: rhombic Hole: with hole — cylindrical hole Chipbreaker: double-sided Grade / coating: T5115 (CVD-coated carbide) Series: ISO indexable turning inserts Typical application: Turning (external and internal) Compatibility: ISO holders determined by form, relief angle, tolerance class, fastening, size and thickness FAQ What materials is this insert best suited for? The DNMG 150412 T5115 indexable insert is optimised for cast iron applications thanks to the T5115 CVD-coated carbide, which balances wear resistance and cutting-edge stability. Which dimensions are critical when selecting a compatible holder? Key dimensions are the inscribed circle 15 mm, thickness 4.76 mm, corner radius 1.2 mm, and the 55° geometry; these determine compatibility with ISO toolholders and clamping systems. How does the double-sided chipbreaker affect machining? A double-sided chipbreaker enables predictable chip formation on both cutting edges, improving chip evacuation and supporting consistent surface quality across repetitive turning operations. Is the insert supplied ready to mount in standard ISO holders? Yes, the insert follows ISO indexable insert conventions and is compatible with holders that match the form, relief angle, tolerance class, fastening method, size and thickness requirements; proper seating is ensured by the cylindrical mounting hole. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide, an ISO rhombic 55° geometry and a reliable double-sided chipbreaker for productive turning of cast-iron components; order the insert directly via Metav Werkzeuge or contact the consultants for compatibility advice. DNMG150412 T5115 ISO turning insert for turning by Tungaloy DNMG150412 T5115 is an ISO-indexable turning insert designed for stable, economical machining of cast iron in ISO-standard holders. CVD-coated carbide for cast iron ISO rhombic 55° geometry 1.2 mm nose radius, 4.76 mm thickness Double-sided chipbreaker with cylindrical hole Consistent chip control for productive cast-iron turning The CVD-coated carbide grade T5115 delivers a balanced mix of wear resistance and cutting-edge stability, making it suitable for typical cast-iron turning tasks. The coating reduces flank wear and improves thermal resistance compared with uncoated grades, so the cutting edge retains its geometry over longer features and interrupted cuts. As a result, cycle times can be maintained with fewer tool changes, supporting more efficient shop-floor routines and predictable batch output. Geometry and rigidity that support precise external and internal turning The insert’s ISO rhombic 55° form and a 1.2 mm nose radius provide a stable engagement in both external and internal turning operations. The 55° approach angle balances axial and radial cutting forces, while the 0° clearance (relief) should be matched with the correct holder geometry to ensure reliable chip flow and minimal chatter. Compatibility with the clamping system is determined by form, clearance angle, tolerance class, fixing type, size and thickness; using the correct holder and shim ensures repeatable positioning and consistent surface finish. Economical handling and quick indexing for continuous production Being double-sided and fitted with a cylindrical hole, the insert permits easy indexing and secure clamping in standard DIN/ISO toolholders, reducing downtime during tool changes. The 4.76 mm plate thickness enhances bending resistance under heavier depths of cut, while the reversible nature of the insert improves tool utilisation per part. For operations where stability and cost-effectiveness are priorities, this grade and geometry combination helps keep tooling costs predictable and machine uptime high. Practical selection hints for process optimisation Select the double-sided chipbreaker style and the T5115 grade according to the component’s material and the machining strategy: roughing requires robust edge strength and generous chip control, while finishing benefits from the smaller nose radius and stable edge condition. The insert is part of a system comprising the insert, a matching external holder or boring bar, a shim/clamp set and replacement screws; ensuring correct combinations reduces assembly time and enhances process reliability. For complex workpieces, trial cuts with conservative feed rates reveal the optimal balance of surface finish and tool life. For ordering, technical compatibility checks or personalised application advice, contact Metav Werkzeuge – Metav Werkzeuge GmbH is available to provide fast consultation and supply the original Tungaloy inserts. Technical Data Article number: 6850206 Manufacturer SKU: TUN6850206 Our SKU: 6850206-Tungaloy Facts Size: 15 mm Nose radius: 1.2 mm Thickness: 4.76 mm Geometry angle: 55° Clearance angle: 0° Special features CVD-coated carbide grade T5115 ISO-compatible rhombic insert Double-sided chipbreaker Cylindrical hole for secure clamping Suitable for turning (external and internal) Material: carbide Model series: ISO-indexable turning inserts FAQ Is this insert suitable for cast iron machining? The T5115 grade is a universal CVD-coated carbide developed for casting materials; the DNMG150412 insert is therefore suitable for cast-iron turning where balanced wear resistance and edge stability are required. Can the insert be used in any DNMG holder? Compatibility depends on holder form, clearance, tolerance class, fixing type, size and thickness; using a holder specified for DNMG 150412 geometry ensures correct clamping and positioning. How many times can the insert be indexed? The insert is double-sided, offering two usable cutting edges per index; actual lifetime per edge depends on cutting data, material, and machine stability. What is the meaning of the 55° geometry for machining performance? A 55° approach angle balances axial and radial loads, improving chip control and allowing stable cutting across a range of depths and feeds in turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5115 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide T5115 for reliable cast-iron performance and the DNMG rhombic geometry with a 1.2 mm corner radius for consistent surface finish; order directly via Metav Werkzeuge or consult our experts for application support. DNMG 150412 T5115 — Turning insert by Tungaloy (CVD-coated carbide, rhombic 55°) DNMG150412 T5115 Tungaloy turning insert for ISO-compatible external and internal turning applications, designed as a universal grade for cast iron with a balanced mix of wear resistance and edge stability CVD-coated carbide grade T5115 Double-sided chipbreaker for repeatable cuts Rhombic DNMG geometry with 55° lead angle Cylindrical hole for secure clamping 1.2 mm corner radius for robust edges Consistent cutting performance for cast-iron turning The CVD-coated carbides used in this grade deliver a practical balance between wear resistance and edge stability, which is essential for medium-duty turning of cast iron. The coating increases resistance to abrasion and built-up edge formation, while the substrate guarantees toughness. For production environments seeking steady tool life and repeatable part quality, this combination reduces process variance and supports predictable machining cycles, lowering scrap rates and improving throughput. Geometry and stability that improve surface finish and tool life The DNMG rhombic shape with a 55° approach gives a compromise between strength and accessibility for external and internal operations. The 1.2 mm corner radius provides additional edge reinforcement, reducing the risk of chipping at interrupted cuts and improving surface finish on standard turning passes. The double-sided chipbreaker enables two usable edges per indexation, which extends service intervals and simplifies inventory management for common turning tasks. Compatibility, clamping and practical handling in the toolroom ISO standardisation of the insert series ensures broad compatibility with matched external holders and boring bars; clamping fit depends on form, relief angle, tolerance class, fastening method, size and thickness. The insert’s cylindrical hole supports secure mechanical clamping and repeatable seating, which is particularly important when switching between holders or when high positional accuracy is required. Stocking ISO-compliant inserts simplifies tool change procedures and minimises downtime. Application guidance and process reliability Designed as a universal grade for cast iron, the T5115 selection is aimed at workshops and small series production where consistent tool life and reliable surface integrity matter. Correct selection of chipbreaker and grade according to material, machining method and machine rigidity will yield the best results. For customers seeking to scale operations, the combination of the CVD-coated grade and ISO geometry offers an economical route to stable production, while reducing the frequency of operator intervention and rework. For tailored advice on how the Tungaloy DNMG150412 T5115 insert fits specific turning tasks, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for application consultancy and ordering support via Metav Werkzeuge. Technical data Article number: 6850209 Manufacturer SKU: TUN6850209 SKU: 6850209-Tungaloy Series: ISO turning indexable inserts Designation: DNMG150412 Grade: T5115 Material: carbide Application: turning Numbers / Core technical data Insert size: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Lead/approach angle: 55° Clearance angle: 0° Special features CVD-coated carbide grade T5115 Rhombic DNMG geometry, double-sided Cylindrical hole for positive clamping ISO-compatible indexable insert series Double-sided chipbreaker Intended for cast iron machining FAQ What materials is this insert best suited for? The Tungaloy DNMG150412 T5115 turning insert (SKU 6850209-Tungaloy) is designed as a universal grade for cast iron and performs well where a balance of wear resistance and edge stability is required. How does the T5115 coating improve performance? The CVD coating on the T5115 grade increases abrasion resistance and reduces built-up edge formation, extending the effective tool life of the insert during typical turning operations. Is the insert compatible with standard ISO holders? Yes, the insert belongs to an ISO indexable insert series; compatibility with a given holder depends on form, relief angle, tolerance class, fastening and size, so ensure the holder matches the DNMG150412 geometry. Can the insert be used for internal turning or boring? The rhombic DNMG geometry and 55° approach make the insert suitable for many external and internal turning tasks when paired with an appropriate boring bar or holder. How many cutting edges are available per insert? The insert is double-sided with a chipbreaker on each side, providing multiple indexations to extend service life and reduce replacement frequency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5115 Wendeplatten - Tungaloy
Combine cost-effective CVD-coated carbide T5115 with a stable edge geometry and optimised double-sided chipbreaker to achieve productive, repeatable cast iron turning; order directly via Metav Werkzeuge or consult the technical team for application advice. DNMG 150412 T5115 Tungaloy turning insert — CVD-coated carbide for cast iron, rhombic DNMG 55° The DNMG150412 T5115 is a rhombic, ISO-standard turning insert engineered for general external and internal turning of cast iron, featuring a double-sided chipbreaker and a cylindrical centre hole for secure clamping CVD-coated carbide grade T5115 Optimised for cast iron machining Rhombic DNMG shape with 55° cutting angle Double-sided chipbreaker, cylindrical hole Longer tool life through balanced coating and grade The combination of a CVD-coated surface and a universal T5115 grade creates a dependable balance between wear resistance and cutting-edge stability. This balance reduces flank wear during extended cycles and supports consistent component tolerances in series production. For workshops seeking measurable gains in uptime, the coated cemented carbide offers a cost-effective route to longer tool life while maintaining predictable regrind intervals. Stable chip control for reliable turning performance A double-sided chipbreaker designed for cast iron yields controlled chip formation and evacuation, lowering the risk of built-up edge and surface damage. The rhombic DNMG geometry with a 55° cutting angle provides a versatile cutting orientation that suits both facing and light profiling. In practical terms, improved chip control means fewer interruptions, more consistent surface quality and higher overall process stability on lathes and bar-fed machines. Compatibility and mounting guidance for shop floor use Compatibility with a toolholder depends on form, relief angle, tolerance class, clamping style, size and thickness. The DNMG format with a cylindrical centre hole and a 0° relief angle is compatible with standard DNMG external holders and boring bars when the holder matches the ISO dimensions. The insert thickness of 4.76 mm and an insert size of 15 mm should be checked against the holder pocket and clamp to ensure correct seating and torqueing of the screw. Practical advantages for cast iron applications Designed as a universal solution for cast iron, this insert supports a wide range of turning tasks from roughing to finishing when feed and speed are adapted to the workpiece and machine rigidity. The corner radius of 1.2 mm contributes to edge strength and improved surface integrity on interrupted cuts. By choosing this CVD-coated grade, manufacturers benefit from reproducible cutting behaviour and simplified grade management across similar cast iron operations. For fast delivery or tailored application advice on the Tungaloy CVD-coated grade T5115, contact Metav Werkzeuge for a personalised recommendation and order processing via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6850204 Manufacturer SKU: TUN6850204 Our SKU: 6850204-Tungaloy Designation: DNMG150412 ISO code: 150412 Grade: T5115 Material: Carbide Coating: CVD Application: Turning Core data Corner radius: 1.2 mm Insert size: 15 mm Thickness: 4.76 mm Relief angle: 0° Cutting angle: 55° Centre hole: cylindrical Double-sided chipbreaker: yes Special features Rhombic insert shape ISO-standard indexable insert Double-sided chipbreaker Compatible with DNMG holders when pocket matches ISO Suited for external and internal turning of cast iron FAQ What materials is this insert intended for? The DNMG150412 T5115 insert is formulated as a universal grade for cast iron, providing balanced wear resistance and edge stability for typical cast iron turning applications. How does the T5115 grade affect tool life? The T5115 CVD-coated grade enhances wear resistance while maintaining edge robustness, which together extend effective cutting life under standard turning conditions. Is the insert compatible with standard DNMG holders? Compatibility depends on the holder matching ISO dimensions for form, relief angle, tolerance class, clamping and thickness; the DNMG150412 fits standard DNMG pockets when those criteria are met. What is the corner radius and how does it influence cutting? The insert has a 1.2 mm corner radius, which increases edge strength and improves surface finish stability, especially on interrupted cuts in cast iron. Does the insert come with a chipbreaker suitable for finishing? Yes, the insert features a double-sided chipbreaker designed to control chips across a range of feeds and depths, supporting both roughing and light finishing operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
DNMG 150412 T5125 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated cemented carbide, a 1.2 mm corner radius and a double-sided chipbreaker for economical turning of cast iron under interrupted cuts — order the insert directly via Metav Werkzeuge or contact our consultants for application advice. DNMG150412 T5125 ISO turning insert for turning applications — Tungaloy, CVD-coated cemented carbide A DNMG150412 T5125 indexable insert engineered for external and internal turning, optimised for interrupted cuts and less stable machining conditions. CVD-coated carbide grade for enhanced toughness Rhombic ISO shape with 55° effective cutting angle Double-sided chipbreaker design for stable chips Compatible with cylindrical-hole clamping systems Increase machining uptime with a tougher cutting grade The CVD-coated cemented carbide composition of this insert delivers improved toughness compared with uncoated grades, making it particularly suitable for interrupted cuts and variable clamping conditions. The harder coating layer resists flank wear while the substrate absorbs impact; together they reduce the frequency of tool changes and support a more consistent production flow. This results in measurable gains in productivity and less unscheduled downtime. Reliable chip control for improved surface finish Equipped with a double-sided chipbreaker, the insert promotes controlled chip formation even when machining cast iron under unstable conditions. Stable chip flow reduces the risk of re-cutting and burr formation, which helps achieve a better surface finish and lowers downstream finishing effort. The combination of chip geometry and the 1.2 mm corner radius balances edge strength with the ability to maintain dimensional tolerances over longer running periods. Geometry and mounting designed for predictable compatibility Designed to the ISO series, the rhombic geometry with a 55° cutting angle and 0° clearance angle ensures predictable behaviour across standard holders. Compatibility with the toolholder depends on form, clearance angle, tolerance class, clamping method, size and thickness — the insert’s 4.76 mm thickness and cylindrical hole make it suitable for many external holders and boring bars. Clear specification reduces setup time and simplifies integration into existing tool systems. Application-led economy and process stability The T5125 grade is a tougher, CVD-coated option selected for machining cast iron where interruptions or less rigid setups occur. Its double-sided design doubles indexable life per insert, offering cost-efficiency across medium to long production runs. Specifying this insert supports stable cutting performance, lowers per-part tooling cost and contributes to repeatable results in batch production. Contact Metav Werkzeuge for tailored cutting data, availability of original Tungaloy inserts and guidance on holder compatibility — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 6850210 Manufacturer SKU: TUN6850210 Brand: Tungaloy Model series: ISO turning indexable inserts Core specifications Size: 15 mm Thickness: 4.76 mm Corner radius: 1.2 mm Cutting angle: 55° Clearance angle: 0° Plate form: rhombic Hole style: cylindrical Double-sided indexing: yes Special features CVD-coated cemented carbide grade T5125 Designed for turning and interrupted cuts Double-sided chipbreaker for chip control ISO series for standard holder compatibility Suitable for cast iron under less stable conditions FAQ What materials is this insert suitable for? The DNMG150412 T5125 is formulated for machining cast iron, particularly where interrupted cuts or less rigid setups occur. How many cutting edges are available per insert? This indexable insert is double-sided, offering more than one usable edge per index and improving cost efficiency. Which holders are compatible with this insert? Compatibility depends on holder form, clearance angle, tolerance class, clamping and size; the rhombic ISO form and cylindrical hole allow use with standard external holders and boring bars that accept DNMG-type inserts. What does the T5125 grade provide compared with standard grades? T5125 is a tougher, CVD-coated carbide grade that improves resistance to impact and flank wear, supporting longer life in interrupted cutting conditions. Are original Tungaloy inserts supplied? Original, brand-new Tungaloy inserts are offered; consult Metav Werkzeuge for availability and cutting parameter recommendations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com