CCGT 060204 GH330 Wendeplatten - Tungaloy
Benefit from the combination of wear-resistant GH330 grade, ISO compatibility and a 0.4 mm corner radius for consistent turning quality and longer tool life; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific guidance. CCGT 060204 GH330 — Indexable turning insert by Tungaloy (rhombic, 0.4 mm radius, single-sided chipbreaker) A CCGT060204 GH330 indexable turning insert designed for general turning operations in ISO-compatible holders, combining a robust carbide grade with chip-control geometry for repeatable results. Rhombic ISO insert CCGT 060204 0.4 mm corner radius GH330 carbide grade Single-sided chipbreaker, 7° relief Productive, predictable cutting performance for turning operations The combination of the GH330 carbide grade and a defined chipbreaker geometry delivers high abrasion resistance alongside reliable edge stability. As an ISO-standard indexable insert, the plate permits consistent interchangeability in production environments, reducing setup variation. The modest 0.4 mm corner radius supports stable engagement in finishing and light-medium roughing passes, while the grade's balance between hardness and toughness helps maintain a sharp cutting edge over extended cycles. This directly translates into fewer tool changes and improved machining throughput. Designed for straightforward integration into ISO holder systems The rhombic plate form and standardised dimensions ensure compatibility with a wide range of external holders and boring bars when form, relief, tolerance class, fastening and thickness match. The 7° relief angle and cylindrical hole with single-sided countersink (40°–60°) provide secure clamping and repeatable seating, which is critical for precision turning. With a 2.38 mm plate thickness and the specified geometry, the insert supports stable clamping forces and minimal vibration, contributing to consistent surface finish and dimensional control. Chip control and surface quality optimised for turning The single-sided chipbreaker is tailored to support effective chip formation and evacuation in many turning scenarios; the actual chip behaviour should be matched to the workpiece material and cutting parameters. The carbide composition enhances thermal stability, allowing reliable performance under moderate cutting temperatures. Where surface integrity is critical, the controlled edge geometry and robust grade help maintain a fine finish across repeated operations, reducing the need for secondary processes. Operational advantages and inventory clarity Standardisation to the ISO form simplifies inventory management and reduces the variety of inserts required for workshop operations. The defined dimensions and ISO compatibility allow for predictable tool life calculations, which assists in process planning and cost control. The insert's stable cutting edge and proven grade reduce unexpected downtime and support reproducible results across batches, improving overall process reliability. For application-specific advice or to secure supply of the Tungaloy GH330 insert, contact Metav Werkzeuge for rapid technical consultation and procurement — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6801295 Manufacturer SKU: TUN6801295 SKU: 6801295-Tungaloy Designation: CCGT060204 GH330 Tungaloy insert Type: CCGT indexable insert Material: Carbide Plate form: rhombic Size: 06 Plate thickness: 2.38 mm Corner radius: 0.4 mm Relief angle: 7° Included angle: 80° Hole: with hole Hole style: cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: single-sided Key Dimensions Size designation: 06 Thickness: 2.38 mm Corner radius: 0.4 mm Relief: 7° Included angle: 80° Radius (rε): 0.4 mm Features ISO-standard indexable rhombic insert Single-sided chipbreaker for controlled chips GH330 carbide grade for wear resistance and edge stability Cylindrical hole + single-sided countersink (40°–60°) Compatible with ISO holders depending on form, clearance, tolerance class, fastening, size and thickness FAQ What materials is this insert suitable for? The CCGT060204 GH330 insert is intended for turning applications; the GH330 grade offers a balance of wear resistance and toughness suitable for a range of common turning materials when the chipbreaker and cutting data are selected appropriately. How is the insert secured in the holder? The insert features a cylindrical hole with a single-sided countersink (40°–60°) for standard clamping systems; correct seating and torque according to the holder specification ensure repeatable positioning and stability. Can this insert be used for internal and external turning? Yes, the rhombic form and geometry support both external and selected internal turning applications when used with a compatible external holder or boring bar matched to the insert dimensions. What are the key dimensions to check for compatibility? Important dimensions include the size designation 06, plate thickness 2.38 mm, corner radius 0.4 mm and the 7° relief; verify these against the holder’s accepted insert forms and tolerance class. How does the GH330 grade influence tool life? The GH330 carbide grade combines hardness and toughness to provide stable cutting-edge behaviour and improved resistance to abrasive wear, which typically results in longer usable life under suitable cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 GH330 Wendeplatten - Tungaloy
High process reliability from ISO geometry and the wear‑resistant GH330 grade ensures stable cutting performance, while the rhombic form with a 0.4 mm corner radius delivers precise profiling in turning operations; order original inserts directly via Metav Werkzeuge or request application advice from our consultants. CCGT060204 GH330 – Rhombic turning insert for turning, Tungaloy, 0.4 mm corner radius The CCGT060204 GH330 is an ISO‑standard rhombic indexable insert intended for external and internal turning, combining a wear‑resistant Tungaloy grade with robust geometry for consistent machining performance. ISO rhombic insert CCGT060204 GH330 grade for wear resistance 0.4 mm corner radius for fine profiling Cylindrical hole with 40°–60° countersink Consistent chip control for predictable productivity The insert’s single-sided chipbreaker design supports reliable chip formation during moderate to heavy cuts, reducing interruptions and machine downtime. Paired with the ISO rhombic geometry, this configuration delivers repeatable chip flow, which is particularly useful in longer production runs where consistent cycle times matter. The combination of geometry and chipbreaker reduces the need for manual chip handling and contributes to improved overall process efficiency. Edge stability and extended wear life through material choice Produced in a Tungaloy grade, GH330 balances wear resistance with toughness to maintain a stable cutting edge under varying cutting conditions. The substrate of cemented carbide provides thermal stability and strength at elevated cutting temperatures, while the grade formulation improves resistance to abrasive wear. As a result, tool life is lengthened and insert changes become less frequent, improving throughput and lowering tooling costs per component. Precision fit and secure clamping for reliable indexing Compatibility with the holder is determined by form, relief angle, tolerance class, clamping method, size and thickness. The insert features a cylindrical hole with a one‑sided countersink (40°–60°) for positive seating and repeatable positioning in standard ISO pockets. The 7° relief angle and 2.38 mm thickness provide a stable mounting platform that minimises vibration and preserves dimensional accuracy across indexings, which supports high‑quality surface finishes and reduced scrap rates. Practical benefits for everyday turning operations The rhombic shape and 0.4 mm corner radius enable accurate profile turning and small radius work without sacrificing edge stability. The insert is suitable for both external and internal operations when paired with the appropriate holder or boring bar. Selection of the GH330 grade and the single-sided chipbreaker should be matched to workpiece material and machining stability to achieve the best balance of surface finish and tool life. Where higher toughness or different chip control is needed, alternate chipbreaker styles and grades can be chosen within the same ISO series. Contact Metav Werkzeuge for tailored application advice and to obtain original Tungaloy CCGT060204 GH330 inserts for dependable turning performance Technical data Article number: 6801301 Manufacturer SKU: TUN6801301 SKU: 6801301-Tungaloy Designation: CCGT060204 GH330 Tungaloy insert Manufacturer: Tungaloy Material: cemented carbide Model series: ISO turning indexable inserts Application: Turning Core specifications Corner radius: 0.4 mm Relief angle: 7° Included angle: 80° Plate thickness: 2.38 mm Plate size: 06 ISO code: 060204 Special features Rhombic plate form Single-sided chipbreaker Cylindrical hole with one-sided countersink (40°–60°) GH330 Tungaloy grade for wear resistance and edge stability Compatible system: ISO insert, outer holder or boring bar, shim/clamp set and screws Intended for external and internal turning operations FAQ What turning operations is this insert best suited for? The CCGT060204 GH330 insert is designed for both external and internal turning where a rhombic geometry and a 0.4 mm corner radius are required; it performs well in general turning tasks with appropriate holder selection. Which materials can be machined with this grade? The GH330 Tungaloy grade offers broad applicability; when combined with the rhombic geometry and single‑sided chipbreaker, it is suitable for a wide range of steels and common industrial materials depending on cutting parameters. How is the insert secured in the holder? The insert uses a cylindrical hole with a one‑sided countersink (40°–60°) for positive seating and repeatable clamping; the 7° relief angle and 2.38 mm thickness ensure a stable, vibration‑resistant mount. Can the corner radius be used for fine profiling? Yes, the 0.4 mm corner radius allows for precise profile turning and small radius features while maintaining edge stability under standard cutting conditions. What is included in the ISO insert system? A compatible system typically comprises the ISO indexable insert, a suitable outer holder or boring bar, an underlay/clamp set and replacement screws to ensure correct seating and clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of coated cermet wear resistance, ISO compatibility and a compact rhombic form for consistent finishing results and longer tool life; order original Tungaloy inserts via Metav Werkzeuge or consult our specialists for the optimal chipbreaker and holder pairing. CCGT 060204 GT9530 indexable turning insert — Tungaloy, coated cermet for finishing The CCGT060204 GT9530 is an ISO-standard rhombic insert designed for external and internal turning where a high-quality surface and extended tool life under stable conditions are required. Coated cermet grade GT9530 ISO-standard indexable insert 0.4 mm corner radius for fine finish One-sided chipbreaker, rhombic 80° Consistent, high-quality surface finish for steel turning The CCGT060204 GT9530 is engineered as a coated cermet solution to deliver a wear-resistant finishing performance on steel when machining conditions are stable. The combination of the GT9530 grade and the small 0.4 mm corner radius supports a fine surface texture while reducing the tendency to form built-up edge. For precision finishing, the material and grade are selected to balance surface quality with predictable tool wear, making this insert suitable where finish and repeatability are priorities without excessive process complexity. Longer tool life and predictable productivity gains In production environments where consistency matters, the coated cermet composition provides a measurable improvement in tool life compared with uncoated grades in comparable finishing tasks. The stable machining characteristics of the grade reduce unexpected downtime and make cost-effectiveness easier to plan for; over continuous runs the result is fewer indexings and less tool change time. These benefits translate into a leaner workflow and a clear rational case for choosing a dedicated finishing-grade insert in serial turning operations. Straightforward compatibility and secure clamping for repeatable results The insert is produced to an ISO-standard geometry and is rhombic with an included angle of 80°, allowing compatibility with a wide range of external holders and boring bars. Key mounting parameters are defined by form, clearance and tolerance class, fastening method, size and thickness; the item features a cylindrical hole with single-side countersink (40°–60°) to suit common clamping systems. With a 7° clearance angle and 2.38 mm thickness, the insert is intended to be used within a system comprising an insert, suitable holder, shim or clamp set and replacement fasteners that match the ISO interface for reliable repeatability. Practical application guidance for shopfloor decision-making This grade is optimised for external and internal turning on steel where finishing to light general-purpose machining is needed. The one-sided chipbreaker is tailored to provide controlled chip formation when workpiece rigidity and machine stability are adequate; choose the chipbreaker and grade according to material, machining type and fixture stability. In practice, the insert performs best when feed and speed are set to favour a finishing pass rather than aggressive roughing, and when coolant or cutting conditions are stabilised to exploit the longer tool life potential of the cermet coating. For tailored recommendations and to secure authentic Tungaloy CCGT inserts for your turning applications, contact Metav Werkzeuge — our consultants will advise on the correct chipbreaker and holder combination and can supply the matching items directly. Technical data Article number: 6997863 SKU: 6997863-Tungaloy Manufacturer SKU: TUN6997863 Model series: ISO turning indexable inserts Material: cemented carbide Numbers / Core technical data Included angle: 80° Corner radius: 0.4 mm Clearance angle: 7° Thickness: 2.38 mm Size designation: 06 Designs / Special features Coated cermet grade GT9530 Rhombic plate form (CCGT) One-sided chipbreaker Cylindrical hole with single-side countersink (40°–60°) ISO-standard indexable geometry Application: external and internal turning on steel FAQ What materials is this insert best suited for? The GT9530 cermet grade is optimised for machining steel in finishing to light universal operations; select the grade and chipbreaker according to the exact steel alloy and stability of the setup. How is the insert mounted and what should be checked for compatibility? Compatibility is determined by the insert form, clearance angle, tolerance class, fastening method, size and thickness; the CCGT060204 requires a matching rhombic holder and appropriate shim/clamp and screw for secure clamping. What advantages does the GT9530 coating offer? The coated cermet composition of GT9530 provides improved wear resistance and a more consistent surface finish with extended tool life in stable finishing applications. Can this insert be used for roughing operations? This insert is designed for finishing to light general-purpose turning; for heavy roughing, a more robust insert geometry and different grade would be recommended. Which chipbreaker is fitted and what does it mean for chip control? The insert features a one-sided chipbreaker, which is intended to produce controlled chips under stable cutting conditions; proper selection of feed and speed enhances chip evacuation and surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 KS05F Wendeplatten - Tungaloy
Benefit from the combination of ISO compatibility, the KS05F Tungaloy grade and reliable chip control for efficient turning operations. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. CCGT060204 KS05F CCGT ISO turning insert — Tungaloy A CCGT060204 KS05F indexable insert engineered for precision external and internal turning in ISO holders. ISO rhombic insert, 06 size KS05F grade for wear and toughness Single-sided chipbreaker for controlled chips Consistent performance for productive turning The KS05F Tungaloy grade combines balanced wear resistance and edge stability on a carbide substrate to maintain cutting performance over extended cycles. This balance reduces unplanned tool changes and supports stable surface quality in serial machining. The rhombic geometry and single-sided chipbreaker promote predictable chip formation, which simplifies chip handling and contributes to shorter process times and higher throughput in turning applications. Designed for secure fit and straightforward pairing with holders Compatibility with clamping systems is determined by the insert shape, 7° clearance, tolerance class, fastening method, size and thickness. The ISO designation indicates the intended seat and mounting form: CCGT060204 denotes a rhombic plate with an 80° included angle, a 0.4 mm radius and a 2.38 mm thickness, while the cylindrical hole with a one-sided countersink (40°–60°) enables firm, repeatable seating in compatible external holders or boring bars. Clear, standardised dimensions reduce setup uncertainty and make tool inventory management easier. Practical applications and system advantages Intended for both external and internal turning, the insert performs best when the chipbreaker and grade are matched to the workpiece material, machining method and machine stability. In practice, pairing this insert with a suitable external holder, a matching shim/clamp set and replacement screws completes a robust system that minimises vibrations and preserves the cutting edge. The rhombic form offers favourable cutting-edge strength for interrupted cuts, while the one-sided chipbreaker assists in consistent chip segmentation, reducing manual intervention and improving shop-floor ergonomics. For genuine Tungaloy CCGT060204 KS05F inserts and application advice, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific turning tasks and to arrange supply through our technical sales team. Technical data Manufacturer article number: 6843406 SKU (manufacturer): TUN6843406 SKU: 6843406-Tungaloy Model series: ISO turning indexable inserts Material: Carbide Application: Turning Facts Corner radius: 0.4 mm Included angle: 80° Clearance angle: 7° Thickness: 2.38 mm Size: 06 ISO code: 060204 Special features Rhombic plate form Cylindrical hole with one-sided countersink (40°–60°) One-sided chipbreaker Tungaloy grade KS05F ISO designation: CCGT060204 Intended use: external and internal turning FAQ Will this insert fit standard CCGT holders? Compatibility depends on holder form, clearance angle, tolerance class, fastening and plate thickness; the CCGT060204 designation indicates the standard geometry to match common CCGT seats. Which materials suit the KS05F grade? The KS05F Tungaloy grade is formulated for a balanced combination of wear resistance and toughness, making the insert appropriate for a broad range of turning tasks when the chipbreaker and machining parameters are selected accordingly. How does the chipbreaker affect machining? The one-sided chipbreaker on this insert is designed to produce controlled chips and stable metal removal, which aids in tool life extension and consistent surface finish during turning. What additional parts are required to assemble a working tool system? A complete system typically comprises the ISO insert, a compatible external holder or boring bar, an underlay/shim and a clamp set with replacement screws to ensure secure and repeatable clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 NS9530 Wendeplatten - Tungaloy
Data inconsistency detected: the material field indicates "Hartmetall" (cemented carbide) while the grade information specifies an "uncoated cermet (NS9530)"; the conflicting material data prevents generation of a reliable product description, as the mismatch between the material type and grade classification raises concerns about the accuracy of the provided information, potentially leading to errors in interpretation, application, or manufacturing processes, which could result in compromised product quality, reduced performance, or even failure in critical applications, making it essential to resolve the discrepancy by verifying the source data, ensuring consistency across all fields, and confirming the correct material and grade combination before proceeding with further documentation or production steps.
CCGT 060204 NS9530 Wendeplatten - Tungaloy
Deliver consistent finishing on steel with the CCGT 060204 NS9530: an ISO‑compliant rhombic turning insert offering a 0.4 mm corner radius and a sharp, uncoated cermet grade for low cutting forces and excellent surface quality. Order directly via Metav Werkzeuge or consult the team for tailored application advice. CCGT 060204 NS9530 Turning insert (80°) – Tungaloy A CCGT 060204 NS9530 indexable turning insert designed for precision finishing of steel in continuous cuts and small depths of cut. Precision finishing cermet grade NS9530 ISO‑compliant rhombic insert 80° geometry 0.4 mm corner radius for fine surface finish Cylindrical hole with single‑side countersink Precision finishing for steel components The insert’s uncoated cermet grade NS9530 ensures a sharp cutting edge and reduced cutting forces, which directly improves surface integrity on machined parts. For external and internal turning operations, the combination of a fine 0.4 mm corner radius and the sharp grade is optimised for continuous cuts and small depths of cut, producing consistent Ra values and reducing secondary finishing. The use of an ISO‑standard insert guarantees a repeatable cutting geometry that supports process reliability and predictable tool life. Fast interchangeability and secure clamping for efficient production As an ISO turning insert, compatibility with a matching holder is determined by shape, relief angle, tolerance class, fastening and thickness. The 80° geometry and 7° relief angle provide stable support in the pocket, while the cylindrical hole with a one‑side countersink (40°–60°) ensures reliable clamping and simple replacement. This standardised system architecture—insert, external holder or boring bar, shim/clamp set and replacement screws—reduces set‑up time, simplifies spare‑parts management and helps maintain consistent cycle times on the shop floor. Application guidance and recommended use Engineered primarily for turning of steel, the finishing‑oriented NS9530 grade performs best where surface quality and low cutting forces are priorities. The single‑side chipbreaker is chosen to match the intended machining stability and material flow; select a chipbreaker and grade combination according to workpiece rigidity and feed range. The rhombic insert form (size 06, thickness 2.38 mm) offers access to confined profiles and internal features while the 80° approach angle balances cutting edge engagement and component geometry control, supporting productive, repeatable results. For specialist recommendations on tooling set‑up or to request application data for a specific workpiece, contact Metav Werkzeuge for expert advice and fast delivery. Technical data Article number: 6997911 Manufacturer SKU: TUN6997911 Model series: ISO turning indexable inserts Designation: CCGT060204 NS9530 Application: Turning Key measurements Geometry: 80° Relief angle: 7° Insert size: 06 Thickness: 2.38 mm Corner radius: 0.4 mm Features and materials Cutting material: uncoated cermet, grade NS9530 Insert shape: rhombic Hole: with hole — cylindrical hole + one‑side countersink (40°–60°) Chipbreaker: single‑side Typical use: external and internal turning FAQ What machining tasks is this insert best suited for? The NS9530 cermet grade is tuned for finishing operations on steel; the CCGT 060204 insert is best used for continuous cuts and small depths where high surface quality is required. How does the insert ensure fast replacement and consistent geometry? As an ISO‑compliant indexable insert, the CCGT 060204 is compatible with standard holders and employs a cylindrical hole with a single‑side countersink for reliable clamping and repeatable positioning. Is this insert suitable for internal turning in confined spaces? Yes; the rhombic shape and size 06 profile of the CCGT 060204 enable access to tighter internal geometries while keeping a stable cutting edge. Which workpiece materials should be avoided with this grade? The NS9530 finishing grade is optimised for steel; alternative grades are recommended for non‑ferrous metals, hardened steels or high‑temperature alloys. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 NS9530 Wendeplatten - Tungaloy
Combining the sharp cutting edge of NS9530, the 80° rhombic geometry and the controlled chip formation of the single-sided breaker, this insert delivers superior surface quality and low cutting forces for finishing steel; order the CCGT060204 NS9530 Tungaloy turning insert directly via Metav Werkzeuge or ask our consultants if needed. CCGT 060204 NS9530 turning insert — rhombic 80° geometry, finishing grade by Tungaloy CCGT060204 NS9530 Tungaloy turning insert is an ISO-standard rhombic finishing insert designed for external and internal turning, optimised for continuous cuts and small depths of cut ISO-standard rhombic insert 80° geometry Uncoated cermet grade NS9530 for finishing Sharp cutting edge for low cutting forces Cylindrical hole with single-sided countersink Delivering consistent finishing performance for steel turning The uncoated cermet NS9530 is formulated for low cutting forces and a sharp cutting edge, which together reduce tool-induced vibration and improve surface quality on steel components. As a finishing grade, the material excels in continuous cuts and small depths of cut, producing consistently high surface finishes that reduce subsequent grinding or polishing steps. The practical outcome is higher first-pass yield and fewer rework cycles. Precision geometry that supports dependable productivity The 80° rhombic geometry and a 0.4 mm corner radius give the insert predictable contact conditions, while the 7° relief angle minimises rubbing and heat build-up. The insert’s 2.38 mm thickness and standardised ISO form ensure mechanical stability in a wide range of holders; the result is improved tool life and repeatable machining results. These measurable advantages translate directly into shorter cycle times and more reliable process windows on turning centres. Compatibility and secure clamping for straightforward setup Designed with a cylindrical hole and a single-sided countersink (40°–60°), the insert fits common ISO holders and clamping kits, enabling quick insert changes and secure fixation. The single-sided chipbreaker manages swarf in finishing operations, supporting stable chip flow without compromising the cleaned surface. If additional setup guidance is required, Metav Werkzeuge provides application advice to select the correct holder, clamping components and cutting parameters for each job. Why this choice supports manufacturing goals Selecting this finishing insert means choosing a solution that balances surface quality and cutting efficiency. The combination of cermet cutting material and rhombic geometry is particularly effective where fine finishes and minimal cutting forces are priorities. For production environments focused on reproducibility and minimal post-processing, this turning insert contributes to predictable results and consistent part quality. Contact Metav Werkzeuge for application advice on the Tungaloy finishing insert or to discuss ordering the CCGT060204 NS9530; reach out at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6997902 SKU: 6997902-Tungaloy Manufacturer SKU: TUN6997902 Facts ISO designation: 060204 Size: 06 Thickness: 2.38 mm Corner radius: 0.4 mm Relief angle: 7° Insert angle: 80° Special features Shape: rhombic Material: carbide substrate with uncoated cermet grade NS9530 Chipbreaker: single-sided Hole: cylindrical hole with single-sided countersink (40°–60°) Application: finishing for steel, suitable for external and internal turning FAQ What materials is this insert suitable for? The CCGT060204 NS9530 Tungaloy turning insert is optimised for steel finishing applications and performs best in continuous cutting and small depths of cut. Which holder types are compatible with this insert? Compatibility depends on holder form, relief angle, tolerance class, fastening and size; the insert’s ISO form, 7° relief and cylindrical hole with countersink suit standard ISO clamping systems. How does the uncoated cermet grade affect surface finish? The NS9530 cermet provides a sharp cutting edge and low cutting forces, which together improve surface quality and reduce the need for downstream finishing. Is the insert suitable for internal as well as external turning? Yes, the insert is designed for both external and internal turning when the correct holder and clamping arrangement are used. What is the manufacturer SKU and article number for ordering? The article number is 6997902 and the SKU is 6997902-Tungaloy for the CCGT060204 NS9530 turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 SH7025 Wendeplatten - Tungaloy
Benefit from the combination of reliable edge stability, a tough coated cemented carbide grade and ISO compatibility for efficient turning operations; order directly via Metav Werkzeuge or consult our specialists for application support. CCGT 060204 SH7025 — Indexable turning insert (rhombic, 80°) by Tungaloy The CCGT060204 SH7025 is an ISO‑standard rhombic indexable insert intended for external and internal turning, designed for machines and toolholders that match its form, relief and fastening dimensions. Rhombic ISO insert, 80° cutting geometry Coated cemented carbide SH7025 grade Cylindrical hole with one‑side countersink Robust edge stability for variable conditions High cutting reliability for turning applications The rhombic geometry with an 80° cutting angle provides a balanced engagement between insert strength and access to external or internal contours, delivering reproducible results in interrupted and continuous cuts. Made from coated cemented carbide in grade SH7025, this insert emphasises edge stability under changing engagement conditions, which reduces the frequency of index changes and supports a steadier cycle time. For operations where small tools or variable entry angles are used, the combination of geometry and substrate pays off in consistent surface finish and tool life. Practical specifications that ensure fit and function Key dimensions are selected to match ISO toolholder standards while keeping setup straightforward: a corner radius of 0.4 mm, a relief angle of 7° and a plate thickness of 2.38 mm. The 0.4 mm radius reduces the risk of built‑up edge on fine turning passes and helps maintain dimensional accuracy at small depths of cut. The relief angle limits rubbing and heat generation at the flank, improving cutting stability when machining steels and alloyed materials. These measurable attributes support straightforward process parameter selection and predictable machining results. Secure clamping and chip control for efficient machining The insert features a cylindrical hole with a one‑side countersink (40°–60°), enabling reliable clamping in centre‑clamped or screw‑clamped holders and quick insert indexing. A single‑side chipbreaker improves chip control for conventional turning tasks, helping to avoid entanglement in long turning cycles and assisting in chip evacuation from the cutting zone. Together, these aspects reduce process interruptions and contribute to safer, more productive turning operations on turning centres and lathes. Material suitability and process advantages The substrate and coating combination of grade SH7025 is engineered for toughness and cutting edge security, making it appropriate where variable engagement and smaller tool bodies are common. This insert performs well across typical turning tasks such as finishing and medium‑duty roughing of steels and alloyed materials; the robust design helps to minimise edge chipping and extend usable life. Because the insert follows ISO norms, compatibility with a wide range of holders and tool systems is simplified, allowing rapid integration into existing tool inventories. Contact Metav Werkzeuge for tailored advice on using Tungaloy SH7025 indexable inserts — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6967404 SKU: 6967404-Tungaloy Manufacturer SKU: TUN6967404 Material: cemented carbide Model series: ISO-Drehwendeschneidplatten Designation: CCGT060204 SH7025 Numbers Cutting angle: 80° Corner radius: 0.4 mm Relief angle: 7° Thickness: 2.38 mm Size: 06 Special features Coated cemented carbide, grade SH7025 Single‑side chipbreaker Rhombic plate form Cylindrical hole with one‑side countersink (40°–60°) Suitable for external and internal turning FAQ What materials is this insert suited to machine? The SH7025 grade insert is designed for turning of steels and a broad range of alloyed materials; its toughness and edge stability make it suitable for variable engagement conditions. How does the insert clamp in the holder? Clamping is achieved via the central cylindrical hole with a one‑side countersink (40°–60°), which ensures secure seating and compatibility with standard ISO toolholders. What advantage does the 0.4 mm corner radius bring? A 0.4 mm radius reduces the risk of chipping during fine finishes and helps maintain dimensional accuracy on narrow cuts. Is the geometry compatible with ISO tool systems? Yes, the insert follows ISO‑standard dimensions and fits holders that match the plate form, size, thickness and relief specifications. Can this insert be used for internal turning as well as external? The rhombic 80° geometry and compact dimensions make it suitable for both external and internal turning tasks where access and insert strength are required. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 SH7025 Wendeplatten - Tungaloy
Take advantage of the combination of coated carbide SH7025 for sustained cutting-edge stability and the rhombic ISO 060204 form for versatile turning performance; order the insert directly via Metav Werkzeuge or consult our team for selection support. CCGT 060204 SH7025 Tungaloy indexable turning insert for turning The CCGT060204 SH7025 is an ISO-standard rhombic indexable insert for external and internal turning, engineered for stable cutting-edge performance in changing engagement conditions. Coated carbide grade SH7025 Rhombic ISO 06 form, 80° included angle 0.4 mm corner radius, 7° clearance angle Cylindrical hole with one-sided countersink Maximised process stability and longer edge life The combination of a coated carbide substrate and the SH7025 grade delivers enhanced toughness and reliable edge integrity, especially where engagement depth varies. The composition is optimised for turning tasks that demand resistance to chipping while retaining wear resistance. With a 0.4 mm corner radius and an effective chipbreaker, the insert supports repeatable surface quality and predictable tool life, reducing unplanned downtime and improving cycle consistency in production environments. Precise fit and simple integration into turning systems Compatibility with toolholders is governed by form, clearance angle (7°), tolerance class, clamping method, size and thickness; the rhombic ISO 060204 geometry ensures broad holder availability. The cylindrical hole with a one-sided countersink (40°–60°) enables secure clamping and straightforward indexing, promoting quick insert changes and repeatable positioning. The plate thickness of 2.38 mm contributes to stiffness in small holders, making it suitable for both external and internal turning operations. Application guidance for efficient machining The single-sided chipbreaker design is intended for general-purpose turning; select the breaker and grade to match workpiece material and machining stability. The insert is particularly effective where smaller tools or variable engagement require a tough, edge-stable grade rather than the hardest substrate. The ISO-format indexable design simplifies inventory management — the same ISO 060204 designation fits a wide range of holders — and replacement screws or clamping sets provide straightforward serviceability during scheduled maintenance. For tailored selection of Tungaloy turning inserts and prompt supply, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best grade and chipbreaker for the intended application Technical data Article number: 6967370 Manufacturer SKU: TUN6967370 Product SKU: 6967370-Tungaloy Model series: ISO indexable turning inserts Facts Size designation: 06 ISO code: 060204 Plate thickness: 2.38 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 80° Materials & features Coated carbide grade SH7025 Rhombic plate form (CCGT) One-sided chipbreaker Cylindrical hole with one-sided countersink (40°–60°) Suitable for external and internal turning Compatibility determined by form, clearance, tolerance, clamping, size and thickness FAQ What materials is this insert designed to machine? The SH7025-coated carbide formulation is designed as a tough, edge-stable grade suitable for a broad range of steels and mixed materials; choose the specific chipbreaker and cutting data according to the workpiece. How does the CCGT060204 fit into existing toolholder systems? The insert follows the ISO 060204 designation, so compatibility depends on holder form, clearance angle, tolerance class, clamping method, size and thickness to ensure correct seating and secure clamping. What is the benefit of the one-sided chipbreaker? A one-sided chipbreaker offers controlled chip formation for many turning operations, balancing chip control with strength at the cutting edge to reduce edge chipping under variable engagement. Is the insert suitable for internal turning as well as external turning? Yes; the rhombic geometry and the plate dimensions make the insert suitable for both external and internal turning, provided the chosen holder and overhang meet the rigidity requirements. Which features improve repeatability when indexing a new edge? The ISO form, the cylindrical hole with countersink and the standardised thickness and tolerance classes provide consistent seating and clamping, supporting rapid, repeatable indexing and minimised re‑set times. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 SH725 Wendeplatten - Tungaloy
Take advantage of the combination of a coated carbide SH725 grade, precise 80° rhombic geometry with a 0.4 mm corner radius, and a secure cylindrical hole with 40°–60° countersink to achieve stable chip control and repeatable edge life in turning operations; order the insert from Metav Werkzeuge or consult their application specialists for holder and clamping recommendations. CCGT060204 SH725 CCGT Rhombic Turning Insert for Turning by Tungaloy — 80° geometry, 0.4 mm radius CCGT060204 SH725 is an ISO‑standard rhombic turning insert designed for robust performance in external and internal turning, optimised for small tools and varying engagement conditions. Coated carbide grade SH725 Rhombic 80° geometry, 0.4 mm corner radius Cylindrical hole with 40°–60° countersink Single-sided chipbreaker for controlled chips Consistent edge stability for productive turning The coated carbide composition and the SH725 grade provide a combination of toughness and edge stability that suits demanding turning tasks and variable cutting conditions. This makes the insert particularly effective where small‑tool setups or frequent changes in depth of cut occur. The rhombic 80° geometry supports positive cutting action and good access to workpiece contours, while the 0.4 mm corner radius balances cutting edge strength with surface finish requirements. These design choices reduce the frequency of index changes and contribute to a smoother production flow. Straightforward mounting and ISO compatibility Compatibility is determined by form, relief angle, tolerance class, fastening, size and thickness; the insert’s ISO‑standard dimensions ensure easy selection of matching holders. The cylindrical hole with single‑sided countersink (40°–60°) delivers secure clamping and repeatable positioning in a wide range of ISO holders and boring bars. A complete system comprises the ISO insert, a corresponding external holder or boring bar, a clamping pad/kit and replacement screws — allowing quick integration into existing tool setups and minimising downtime during tool changes. Controlled chip formation and application scope The single‑sided chipbreaker is tuned for reliable chip control in standard turning operations, helping to avoid entanglement and facilitating safe chip evacuation. Typical applications include both external and internal turning where reproducible chip shape and stable cutting edges matter. The insert’s coated carbide nature improves wear resistance on medium‑duty cuts, while the SH725 composition is selected for its toughness and resistance to edge chipping, which is beneficial when engagement conditions change during interrupted cuts. Practical selection and support for production Selection of chipbreaker type and grade should match the workpiece material, machining strategy and machine stability; the provided data indicate the insert is prepared for versatile turning tasks rather than a single specialised niche. For machining teams requiring guidance on choosing the correct holder, clamping set or feed and speed recommendations, professional consultation is available. Technical queries and compatibility checks can be addressed quickly to ensure the insert integrates with existing toolholders and clamping hardware. Contact Metav Werkzeuge for application advice, availability of the Tungaloy CCGT060204 SH725 insert and recommended holders; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6737129 Manufacturer SKU: TUN6737129 SKU: 6737129-Tungaloy Model series: ISO‑Drehwendeschneidplatten Designation: CCGT060204 SH725 Tungaloy‑Wendeplatte Core figures Corner radius: 0.4 mm Geometry angle: 80° Relief (free) angle: 7° Thickness: 2.38 mm Insert size: 06 Mounting: with hole Hole style: cylindrical hole + one‑sided countersink (40°–60°) Features & application Coated carbide grade SH725 Rhombic insert form (CCGT) Single‑sided chipbreaker Intended use: Turning (external and internal) Compatibility: ISO holders, clamping pad/kit and replacement screws Suited to small tools and varying engagement conditions FAQ What applications is this insert best suited for? The Tungaloy CCGT060204 SH725 insert is intended primarily for external and internal turning where a balance of edge stability and toughness is required. How is the insert secured in the holder? The insert is held via a cylindrical hole with a single‑sided countersink (40°–60°); this design provides secure clamping and repeatable positioning in ISO holders. Which holder and clamping components are needed? A matching ISO external holder or boring bar, a clamping pad/kit and replacement screws complete the system; compatibility depends on form, relief angle, tolerance and insert thickness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 SH725 Wendeplatten - Tungaloy
Take advantage of the combination of coated carbide SH725 edge stability and ISO‑standard compatibility for reliable turning operations; order the insert directly via Metav Werkzeuge or consult the technical team for application support. CCGT060204 SH725 CCGT turning insert, coated carbide, rhombic 06 — Tungaloy The CCGT060204 SH725 is an ISO‑standard rhombic turning insert designed for external and internal turning, offering a tough, edge‑stable grade for variable engagement and smaller tool setups. Coated carbide grade SH725, edge stability Rhombic 06 form with 80° included angle 0.4 mm nose radius for balanced finish and strength Single‑sided chipbreaker for consistent chip control Consistent cutting performance where edge stability matters The coated carbide SH725 grade delivers a balance of toughness and wear resistance that supports repeatable performance in changing engagement conditions. The 0.4 mm nose radius increases component strength at the cutting edge while still enabling a good surface finish for general turning tasks. Specified as an ISO‑standard insert in the rhombic 06 format, this geometry provides a dependable cutting angle and predictable tool life; the 80° included angle gives a robust cutting edge suited to a wide range of turning operations. For production environments that value process stability, the combination of grade and geometry reduces unexpected tool failures and supports steady cycle times. Secure mounting and fast tool changes to reduce downtime The insert features a cylindrical hole with a single‑side countersink (40°–60°) for secure clamping in compatible holders, and the 2.38 mm plate thickness contributes to mechanical stiffness during cutting. Compatibility with a toolholder is governed by form, relief angle, tolerance class, attachment method, size and thickness, so using ISO‑compliant holders and the correct clamping set ensures repeatable seating and fast index changes. The system composition — insert, outer holder or boring bar, shim/clip and replacement screws — is straightforward, enabling quick swaps and minimised setup time on the shop floor. Practical application guidance and selection tips The single‑sided chipbreaker is designed to promote reliable chip formation under a variety of cutting conditions; select the chipbreaker and grade to match the workpiece material and the nature of the cut (continuous vs interrupted). The moderate 7° clearance angle helps to avoid rubbing while maintaining edge support, and the rhombic shape gives flexibility for both external and internal turning. For operations using smaller tools or encountering variable entry and exit conditions, this grade and geometry provide a resilient option that manages edge wear and supports sustained productivity. When specifying inserts for a machining process, consider geometry, nose radius and clamping method as primary factors for achieving the desired surface finish and tool life. Contact Metav Werkzeuge for technical advice, availability of Tungaloy SH725 inserts and recommendations for compatible holders and clamping sets; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6737244 SKU: 6737244-Tungaloy Manufacturer SKU: TUN6737244 Manufacturer: Tungaloy Facts Nose radius: 0.4 mm Included angle: 80° Clearance angle: 7° Plate thickness: 2.38 mm Plate size: 06 Special features ISO turning insert series Coated carbide grade SH725 Rhombic plate form Single‑sided chipbreaker Cylindrical hole with single‑side countersink (40°–60°) Compatible for external and internal turning System composed of insert, holder or boring bar, shim/clip and replacement screws FAQ What cutting operations is this insert suited for? The CCGT060204 SH725 insert by Tungaloy is designed primarily for external and internal turning where a tough, edge‑stable grade is required; it performs well in variable engagement conditions and with smaller tooling setups. How does the 0.4 mm nose radius affect the result? A 0.4 mm nose radius offers a compromise between strength and finish: the radius increases edge support and tool life while still enabling acceptable surface quality for general turning tasks with the SH725 grade. Which clamping features ensure secure mounting of the insert? The insert uses a cylindrical hole with a single‑side countersink (40°–60°) which, together with the matching holder and clamping set, provides secure seating and repeatable positioning for reliable tool changes. Is the insert compatible with standard ISO holders? Yes; the insert is ISO‑standard in the rhombic 06 format, but compatibility depends on holder form, tolerance class, attachment method, size and thickness — using matching ISO holders and the correct clamping hardware is recommended. What are the distinguishing characteristics of the SH725 grade? SH725 is a coated carbide grade engineered for toughness and a stable cutting edge, making it suitable for applications with changing cutting conditions or where small tool sizes are used; this supports consistent machining performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 060204 SH730 Wendeplatten - Tungaloy
Take advantage of the coated carbide SH730 grade and the precise 80° rhombic geometry for stable, productive turning; order the insert directly via Metav Werkzeuge or contact the consultants for specification advice. CCGT 060204 SH730 turning insert – ISO rhombic, 80°, Tungaloy The CCGT 060204 SH730 is an ISO‑standard rhombic turning insert designed for external and internal turning, offering a balanced combination of edge toughness and predictable chip control. Coated carbide grade SH730 Rhombic ISO 06 geometry, 80° cutting angle 0.4 mm corner radius for fine finishing Cylindrical hole with single‑side countersink Consistent cutting performance for mixed turning operations The CCGT 060204 SH730 insert delivers dependable cutting performance across a wide range of turning tasks. The SH730 coated carbide grade is formulated for edge toughness and resistance to chipping, which reduces unplanned tool changes and supports uninterrupted production. As the insert is ISO‑standard, it integrates into established machining systems, allowing process planners to maintain cycle times while improving tool life. The one‑sided chipbreaker is optimised for controlled chip formation, which aids coolant penetration and reduces rework. Precision geometry for secure clamping and predictable results Engineered geometry ensures reliable clamping and repeatable results: the rhombic plate form with an 80° main cutting angle provides a robust cutting edge for facing and profile turning, while the 7° clearance angle prevents rubbing during radial engagement. Compatibility to the holder is determined by form, clearance, tolerance class, clamping method, size and thickness; this insert's 2.38 mm plate thickness and ISO 06 size are standard for many external holders and boring bars. The 0.4 mm corner radius supports fine surface finishes without sacrificing stability. Grade and chip control for efficient, low‑risk machining The SH730 grade is a coated, tough carbide designed for variable engagement conditions and smaller tool bodies where sudden load changes can occur. The single‑sided chipbreaker promotes consistent chip flow, helping to avoid chip jamming in confined spaces. For best results, the chipbreaker and grade should be selected in accordance with the workpiece material and cutting parameters; the insert is suited for both roughing and finishing when matched to the correct parameters. The cylindrical hole with a single‑side countersink (40°–60°) ensures secure fastening and repeatable positioning during index changes. For specification support or to source the CCGT 060204 SH730 Tungaloy turning insert, contact Metav Werkzeuge for professional advice and ordering assistance. Technical data Article number: 6854008 SKU: 6854008-Tungaloy Manufacturer SKU: TUN6854008 Model series: ISO turning indexable inserts Designation: CCGT060204 SH730 Numbers / Core technical data Corner radius: 0.4 mm Cutting angle: 80° Clearance angle: 7° Plate thickness: 2.38 mm Plate size: 06 ISO code: 060204 Designs / Special features Coated carbide grade SH730 Rhombic plate form One‑sided chipbreaker With hole: cylindrical hole + one‑side countersink (40°–60°) Intended application: turning (external and internal) Compatibility depends on form, clearance, tolerance class, clamping, size and thickness FAQ What holder types are compatible with this insert? Compatibility is determined by form, clearance, tolerance class, clamping method, size and thickness; the CCGT 060204 SH730 fits standard ISO holders for size 06 inserts and uses the cylindrical hole with countersink for secure clamping. Which workpiece materials are suitable for this grade? The SH730 coated carbide insert is developed for a broad material range and is particularly effective where edge toughness is required; selection of the chipbreaker should match the specific workpiece material and machining strategy. How does the corner radius influence the surface finish? A 0.4 mm corner radius on the insert provides a balance between finish and strength: it supports finer surface quality while maintaining sufficient edge stability for interrupted cuts. Is this insert suitable for internal turning and small‑diameter tools? Yes, the insert's design and SH730 grade make it suitable for internal and external turning, including applications with smaller tool bodies and varying engagement conditions. What does the ISO code 060204 indicate? The ISO code denotes the insert geometry and dimensions: size 06, thickness and tolerance parameters consistent with ISO‑standard indexable inserts; the 060204 code helps ensure correct holder and seat matching. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 TH10 Wendeplatten - Tungaloy
Take advantage of the ISO compatibility, low cutting forces of the TH10 grade and the fine 0.4 mm corner radius for consistent finishing and productive turning cycles. Order the CCGT060204 TH10 Tungaloy insert directly via Metav Werkzeuge or consult our specialists for application matching. CCGT060204 TH10 indexable turning insert — Tungaloy CCGT060204 TH10 is an ISO-standard rhombic indexable insert designed for external and internal turning, optimised for non-ferrous materials and low-force finishing applications. ISO-standard rhombic geometry TH10 uncoated carbide for non-ferrous metals 0.4 mm corner radius for fine surface finish Cylindrical hole with 40°–60° countersink Consistent cutting performance for non-ferrous turning The ISO design and the TH10 uncoated carbide grade deliver reliably low cutting forces and clean surfaces when machining aluminium and other non-ferrous materials. The rhombic geometry and the 0.4 mm corner radius support fine finishing passes while maintaining stable chip formation. For production environments where surface integrity and repeatability matter, this combination reduces rework and helps to preserve tool life under suitable cutting conditions. Clear compatibility and reliable clamping for safe operation Compatibility with toolholders is determined by shape, clearance angle, tolerance class, clamping method, size and thickness. The insert is supplied with a cylindrical centre hole and a single-sided countersink (40°–60°), enabling secure mounting in ISO holders that accept CCGT-type plates. The 7° clearance angle and 2.38 mm plate thickness are part of the specification to check when selecting a matched holder to ensure correct seating and repeatable cutting geometry. Practical advantages of an uncoated carbide grade An uncoated carbide microstructure in the TH10 grade keeps the cutting edge sharp and reduces the tendency to build up material when machining soft, gummy alloys. The absence of a coating lowers cutting temperatures and cutting forces in certain non-ferrous applications, which supports improved surface finish and helps to avoid smearing on the workpiece. Where abrasion resistance is less critical than edge sharpness, this grade offers an efficient solution. How to select the right chipbreaker and application set-up The insert is fitted with a single-sided chipbreaker; select the chipbreaker and grade based on the workpiece material, depth of cut and machine rigidity. For high-feed finishing choose small depths with fine edge radii, while for roughing larger depths and appropriate feed rates are advised. If uncertain about the optimal setup, request cutting data for similar alloys and the recommended feeds and speeds to align process stability with productivity. For precise non-ferrous turning with a sharp, low-force cutting edge, request the Tungaloy CCGT060204 TH10 insert from Metav Werkzeuge — quote SKU TUN6801303 for exact identification and technical matching, or contact info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice Technical Data Article number: 6801303 Manufacturer SKU: TUN6801303 Vendor SKU: 6801303-Tungaloy Model series: ISO turning indexable inserts Facts Corner radius: 0.4 mm Included angle: 80° Clearance angle: 7° Plate thickness: 2.38 mm Plate size: 06 ISO designation: 060204 Special features Carbide, uncoated Grade TH10 Single-sided chipbreaker Cylindrical hole with single-sided countersink (40°–60°) Rhombic plate form (CCGT) ISO-standardised turning insert Application: external and internal turning, non-ferrous materials Compatibility depends on form, clearance angle, tolerance class, clamping, size and thickness FAQ What materials is this insert suitable for? The CCGT060204 TH10 insert is optimised for non-ferrous materials; the TH10 uncoated carbide grade promotes sharp cutting and clean surfaces when turning aluminium and similar alloys. How is the insert secured in the holder? The insert features a cylindrical centre hole with a single-sided countersink (40°–60°) and requires an ISO-compatible holder that matches the plate form, thickness (2.38 mm) and clamping arrangement. What edge preparation does the insert have? This indexable insert has a 0.4 mm corner radius and a 7° clearance angle, designed to support fine finishing cuts and reduce surface smearing in soft metals. Is the CCGT060204 TH10 suitable for internal as well as external turning? Yes, the ISO rhombic geometry and standard mounting allow use for both external and internal turning operations when paired with the correct holder and process parameters. Which SKU should be referenced when ordering? Use SKU TUN6801303 or vendor SKU 6801303-Tungaloy to ensure the correct TH10 CCGT060204 turning insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 TH10 Wendeplatten - Tungaloy
CCGT060204 TH10 CCGT Wendeplatte zum Drehen von Tungaloy Die CCGT060204 TH10 ist eine ISO-genormte, rhombische Wendeplatte für das Außen- und Innendrehen, entwickelt für niedrige Schnittkräfte und saubere Oberflächen bei Nichteisenwerkstoffen ISO-genormte Wendeplatte für präzise Drehprozesse Unbeschichtete Hartmetall-Sorte TH10 für niedrige Schnittkräfte Rhombische Form 06 für vielseitige Halterkompatibilität Mit Loch und zylindrischer Senkung für sichere Befestigung Eckenradius 0,4 mm für feine Oberflächenqualität Präzise Schneidkante für saubere Oberflächen Die Kombination aus Hartmetall und der unbeschichteten Sorte TH10 sorgt für eine sehr scharfe Schneidkante, die speziell bei Nichteisenwerkstoffen niedrige Schnittkräfte ermöglicht. Dadurch reduziert sich die Wärmeentwicklung und die Gefahr von Aufbauschneiden; das Resultat ist eine verbesserte Oberflächenqualität und geringerer Werkzeugverschleiß. Für Betriebe, die saubere Schnittkanten und stabile Spanbildung erwarten, bietet diese Wendeplatte ein hervorragendes Kosten-Nutzen-Verhältnis. Vielseitige Einsetzbarkeit und Kompatibilität Dank der rhombischen Plattenform und der ISO-Genormtheit lässt sich die Platte in einer breiten Palette von Außenhaltern und Bohrstangen einsetzen. Beim Austausch ist auf Form, Freiwinkel, Toleranzklasse und Plattendicke zu achten, damit Halter und Platte optimal zusammenwirken. Die CCGT060204 TH10 unterstützt eine einfache Integration in vorhandene Werkzeugbestückungen und reduziert Rüstzeiten durch standardisierte Abmessungen. Montage- und Befestigungssicherheit für industrielle Fertigung Die Wendeplatte ist „mit Loch“ ausgeführt; der zylindrische Lochstil mit einseitiger Senkung (40°–60°) gewährleistet eine sichere Positionierung auf dem Halter und eine reproduzierbare Spannkraft. In Kombination mit der Plattendicke von 2,38 mm und dem Freiwinkel von 7° ergibt sich eine stabile Schnittlage, die Vibrationen verringert und die Standzeit erhöht. Diese Eigenschaft ist besonders relevant bei Serienfertigung und anspruchsvollen Längs- und Planbearbeitungen. Wirtschaftlichkeit durch gezielte Werkstoffwahl Die Entscheidung für eine unbeschichtete Hartmetallsorte kann wirtschaftlich sein, wenn die Bearbeitung auf niedrige Schnittkräfte und saubere Oberfläche ausgelegt ist. Durch die optimierte Spanbildung und die robuste Geometrie reduziert sich die Werkzeugwechselhäufigkeit; das führt zu kürzeren Stillstandszeiten und besseren Ausbringungsraten. Die CCGT060204 TH10 eignet sich deshalb besonders für Anwender, die Prozessstabilität und geringe Gesamtkosten pro Bauteil priorisieren. Empfehlung: Für produktive Zerspanung mit niedrigen Schnittkräften die CCGT060204 TH10 von Tungaloy über Metav Werkzeuge anfragen; bei Bedarf technische Daten per E‑Mail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 klären Produktmerkmale Artikelnummer: 6801293 Marke: Tungaloy Modellserie: ISO-Drehwendeschneidplatten Bezeichnung: CCGT060204 TH10 Hersteller SKU: TUN6801293 Fakten Plattengröße: 06 Plattendicke: 2,38 mm Eckenradius: 0,4 mm Freiwinkel: 7° Winkel: 80° Besonderheiten Material: Hartmetall Schneidstofftyp: unbeschichtetes Hartmetall Sorte: TH10 Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig FAQ Welche Werkstoffe sind für die CCGT060204 TH10 geeignet? Die CCGT060204 TH10 von Tungaloy ist speziell für Nichteisenwerkstoffe ausgelegt; die unbeschichtete Hartmetall-Sorte TH10 unterstützt dabei niedrige Schnittkräfte und saubere Oberflächen. Wie beeinflusst der Eckenradius die Oberflächenqualität? Ein Eckenradius von 0,4 mm bietet eine feine Schnittkante, die zu einer verbesserten Oberflächenqualität und geringerer Nacharbeit bei Drehprozessen führt. Welche Bedeutung hat das zylindrische Loch mit Senkung? Das zylindrische Loch mit einseitiger Senkung (40°–60°) sorgt für sichere Befestigung auf dem Halter und für reproduzierbare Positionierung bei Serienwechseln. Wie wähle ich den passenden Halter für diese Wendeplatte aus? Achten Sie auf Form, Freiwinkel, Toleranzklasse, Befestigungsart, Größe und Dicke des Halters, damit die ISO-genormte CCGT060204 TH10 optimal sitzt und vibrationsfrei läuft. Ist die Platte für Innen- und Außendrehen verwendbar? Ja, die ISO-Genorm und die rhombische Form ermöglichen den Einsatz sowohl beim Außen- als auch beim Innendrehen, abhängig von Halterwahl und Bearbeitungsbedingungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCGT 060204 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp, uncoated carbide grade and ISO compatibility to ensure low cutting forces and reliable surface quality; the robust rhombic geometry and single-sided chipbreaker promote consistent chip control and productivity in turning operations. Order directly via Metav Werkzeuge or consult our specialists for application support. CCGT 060204 TH10 ISO turning insert, uncoated carbide, 0.4 mm radius — Tungaloy A CCGT060204 TH10 ISO-indexed turning insert engineered for external and internal turning, offering a sharp, universal uncoated carbide grade for low cutting forces on non-ferrous materials Rhombic insert in ISO 06 size Uncoated carbide TH10 grade 0.4 mm corner radius Single-sided chipbreaker, with hole Consistent low cutting forces and improved surface finish The TH10 grade is an uncoated carbide developed for applications that demand reduced cutting resistance and clean part surfaces. In practice, this means fewer burrs and lower spindle loads when machining aluminium, brass and similar alloys. The combination of a sharp edge geometry and a finely tuned chipbreaker supports predictable chip formation, which reduces vibration and helps achieve a stable process window. For production environments seeking repeatable part quality, this specification translates into tangible cycle-time stability and fewer reworks. Easy integration into ISO tooling systems for rapid setup As an ISO-series insert, the component matches standard clamping systems when the holder’s shape, clearance angle, tolerance class, fastening arrangement, size and thickness correspond. The presence of a cylindrical hole with a single-sided countersink (40°–60°) enables secure retention in common clamping plates, while the 2.38 mm plate thickness contributes to mechanical rigidity in the cutting zone. These measurable compatibilities simplify tool changeovers and minimise downtime, supporting efficient throughput in mixed-production or jobbing shops. Geometry designed for durability and reliable chip control The rhombic shape with an 0.4 mm corner radius offers a balance between edge strength and the ability to generate fine surface finishes. The single-sided chipbreaker encourages controlled chip separation for the target materials, lowering the risk of long, stringy chips that can foul the process. Together, these aspects improve tool life under recommended cutting conditions and allow machinists to exploit the grade’s sharpness without compromising edge stability. The result is predictable wear behaviour and consistent component quality across batches. Practical application guidance for turning tasks Designed for both outside and inside turning, the insert performs best when the single-sided chipbreaker and TH10 grade are selected according to workpiece material, cutting strategy and machine/tool stability. Where light engagement and fine finishes are required, the uncoated edge supports reduced cutting forces; where more robust removal is needed, consider adjusting feed and depth to maintain edge life. For quick specification checks, reference the ISO designation and the manufacturer SKU to confirm compatibility with the chosen holder and clamping set. For technical advice on integrating this Tungaloy uncoated carbide insert into existing toolholders or to reserve stock under SKU TUN6801298, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for tailored support Technical data Manufacturer article number: 6801298 SKU: 6801298-Tungaloy Model series: ISO turning indexable inserts Core data ISO designation: CCGT060204 Format: 06 Plate thickness: 2.38 mm Clearance angle: 7° Included angle: 80° Corner radius: 0.4 mm Special features Material: carbide Grade: TH10 (uncoated) Shape: rhombic Chipbreaker: single-sided Hole: cylindrical with single-sided countersink (40°–60°) Application: turning (external and internal) Compatibility determined by holder form, clearance, tolerance, fastening, size and thickness FAQ What materials is this insert optimised for? The insert is optimised for non-ferrous materials; the TH10 uncoated carbide grade promotes low cutting forces and clean surfaces when machining aluminium and similar alloys. Can this ISO insert be used in standard holders? Yes. The CCGT060204 TH10 follows ISO geometry; compatibility requires matching the holder’s form, clearance angle, tolerance class, fastening and plate thickness. What does the 0.4 mm corner radius mean for my parts? A 0.4 mm radius balances edge strength and finish quality, offering improved durability compared with finer radii while still producing good surface finishes on turning operations. How does the single-sided chipbreaker affect chip control? The single-sided chipbreaker is designed to produce consistent chip segmentation for the intended materials, reducing the occurrence of long swarf and helping maintain stable machining conditions. Which SKU should be quoted when ordering? Please refer to SKU TUN6801298 or manufacturer article number 6801298 when enquiring or ordering this ISO-indexed insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060204 UX30 Wendeplatten - Tungaloy
Take advantage of the combination of precise ISO compatibility, a sharp UX30 carbide cutting edge, and a secure clamping interface for dependable turning results; order the insert directly via Metav Werkzeuge or consult the company's technical advisors for holder matching and application advice. CCGT060204 UX30 CCGT turning insert — Tungaloy, rhombic 06, 7° clearance The CCGT060204 UX30 Tungaloy turning insert designed for ISO‑standard external and internal turning, offering a sharp cutting edge for low cutting forces and consistent chip formation. ISO‑compatible rhombic insert, size 06 UX30 uncoated carbide with sharp cutting edge Single‑sided chipbreaker, cylindrical hole 7° clearance, 2.38 mm thickness, 80° angle Precise ISO fit for predictable machining performance The ISO‑compatible rhombic geometry ensures reliable seating in standard external holders and boring bars; compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness so correct pairing reduces setup variability. The standardised contour and the cylindrical hole with single‑side countersink provide repeatable clamping and stable cutting conditions, which lowers the risk of chatter and contributes to consistent component tolerances in series production. Sharp uncoated carbide grade for low cutting forces and clean chips The insert is supplied in uncoated carbide (UX30) with a deliberately sharp cutting edge and a single‑sided chipbreaker optimised for controlled chip formation. This combination is intended for applications where low cutting forces and efficient chip evacuation are priorities; the result is reduced load on the machine spindle and improved surface quality on turned parts. The design supports both external and internal turning tasks while maintaining effective heat distribution at the cutting zone. Small radius and secure clamping for fine profiles and productivity A 0.4 mm corner radius together with an 80° main cutting angle enables fine profiling and accurate radii on shafts and bores, while the 2.38 mm plate thickness gives sufficient rigidity for standard turning operations. The insert’s hole style (cylindrical hole plus one‑sided countersink at 40°–60°) and ISO form facilitate secure retention with ISO holders and clamping sets, improving tool life and reducing downtime for insert changeovers. For precise holder matching and to maximise process reliability, Metav Werkzeuge can advise on the correct holder and clamping components. For precise, cost‑effective turning with Tungaloy carbide inserts, contact Metav Werkzeuge for ordering and detailed holder compatibility — eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930 Technical Data Article number: 6801299 SKU: 6801299-Tungaloy Manufacturer SKU: TUN6801299 Model series: ISO‑Drehwendeschneidplatten Designation: CCGT060204 UX30 Tungaloy insert Material: carbide Core specifications Main cutting angle: 80° Corner radius: 0.4 mm Clearance angle: 7° Plate thickness: 2.38 mm Insert size: 06 ISO code: 060204 Features and compatibility Rhombic plate form Single‑sided chipbreaker Cylindrical hole + one‑sided countersink (40°–60°) Uncoated carbide grade UX30 Application: turning (external and internal) Compatible with ISO holders, clamping sets and replacement screws FAQ Which holder types are compatible with this insert? The CCGT060204 UX30 Tungaloy insert fits holders and boring bars that accept the ISO rhombic CCGT format; compatibility is defined by form, clearance angle, tolerance class, fastening, size and thickness. Is the insert coated or uncoated? This grade is supplied as uncoated carbide (UX30); the sharp cutting edge is intended for operations prioritising low cutting forces and good chip control. For which turning tasks is the insert recommended? The insert is designed for both external and internal turning where a small corner radius and stable chip formation are required, particularly when low cutting forces are advantageous. What does the chipbreaker design provide? The single‑sided chipbreaker on this insert promotes controlled chip formation and evacuation, which helps maintain surface finish and reduces the likelihood of chip entanglement in turning operations. How does the 0.4 mm corner radius affect the finish? A 0.4 mm corner radius balances edge strength and the ability to produce fine profiles; it supports good surface quality on shafts and small turned features. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 J740 Wendeplatten - Tungaloy
Take advantage of the combination of durable carbide and the J740 cutting grade for consistent tool life and reliable chip control in demanding turning operations; the ISO rhombic 80° geometry with a 7° clearance delivers stable cutting performance. Order the CCGT09T300 J740 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. CCGT 09T300 J740 — ISO turning insert for turning (Tungaloy) CCGT09T300 J740 is an ISO‑standard rhombic 80° indexable insert engineered for external and internal turning, featuring a 7° clearance angle and a cylindrical hole with a single‑side countersink. ISO rhombic 80° geometry for versatile turning J740 Tungaloy grade for wear resistance Cylindrical hole with single‑side countersink 7° clearance and 3.97 mm thickness for stability Maximise machining uptime with a grade built for wear resistance The combination of carbide substrate and the J740 cutting grade is designed to balance wear resistance and edge stability, extending tool life under continuous production. The rhombic 80° geometry concentrates cutting forces for predictable tool behaviour, while the moderate 7° clearance reduces rubbing and helps maintain a consistent cutting edge. These characteristics result in fewer tool changes and improved process reliability, which supports higher productivity in turning applications. Fast, reliable set-up and predictable compatibility Compatibility with the clamping system is determined by insert form, clearance angle, tolerance class, fixation method, size and thickness; matching these parameters ensures a secure fit and repeatable positioning. The insert is intended for use with an appropriate external holder or boring bar, plus a support pad, clamp set and replacement screws where required. Selecting the correct single‑side chipbreaker and matching the grade to the workpiece material will produce stable chips and reduce rework, simplifying process planning across varied turning tasks. Clear technical advantages for everyday production The CCGT09T300 designation identifies an ISO‑conforming insert with a rhombic shape and size 09, a plate thickness of 3.97 mm and a hole style that combines a cylindrical bore with a 40°–60° countersink for secure clamping. The one‑sided chipbreaker is intended to manage chip formation effectively in a broad range of steels and alloys when the correct grade and geometry are selected. For production environments requiring repeatable quality and stable surface finish, the insert’s design translates directly into lower scrap rates and more consistent component tolerances. For specification support or to secure a supply of the J740 grade inserts, contact Metav Werkzeuge for personalised technical advice and fast delivery Technical data Article number: 6801308 Manufacturer SKU: TUN6801308 Listing SKU: 6801308-Tungaloy Model series: ISO turning indexable inserts Facts Geometry angle: 80° Clearance angle: 7° Plate thickness: 3.97 mm Size: 09 Special features Material: carbide Grade: J740 (Tungaloy) Shape: rhombic Chipbreaker: one‑sided Hole: cylindrical with single‑side countersink (40°–60°) ISO designation: CCGT09T300 Application: turning (external and internal) FAQ What materials can this insert machine effectively? The J740 grade insert is designed for a broad range of turning applications; the CCGT09T300 insert performs well on many steels and alloyed materials when the appropriate chipbreaker is selected. How does the 7° clearance affect machining? A 7° clearance angle reduces flank contact and helps preserve the cutting edge; this results in more consistent surface finish and longer insert life for the specified turning operations. Which holder characteristics must match the insert? Secure and repeatable clamping depends on the holder’s form, free angle, tolerance class, fixation and size to suit the ISO rhombic insert CCGT09T300. Is this insert suitable for internal turning and boring bars? Yes; the indexable insert is intended for both external and internal turning provided the correct holder and mounting hardware are used. Are spare screws and clamp sets required for safe operation? A complete system typically comprises the insert, a compatible external holder or boring bar, a support pad, a clamp set and replacement screws to ensure safe and stable operation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 J740 Wendeplatten - Tungaloy
Reliable machining is achieved through the combination of ISO conformity and the Tungaloy J740 carbide grade, delivering consistent edge stability and extended tool life; the rhombic 09 geometry with an 80° cutting angle and a 7° clearance ensures controlled chip formation for both external and internal turning. Order the CCGT09T300 J740 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. CCGT09T300 J740 ISO turning insert, rhombic 09, 80°, 7° — Tungaloy A CCGT09T300 J740 ISO-standard turning insert intended for external and internal turning, combining a wear-resistant carbide grade with a single-sided chipbreaker for dependable, repeatable machining. ISO-standard rhombic insert, size 09 J740 grade Tungaloy carbide for wear resistance 7° clearance angle for stable cutting action Cylindrical hole with 40°–60° countersink Consistent fit and measurable process reliability The ISO standardisation of the insert ensures compatibility with holders when matched by form, clearance angle, tolerance class, fastening type, size and thickness. A correct match reduces vibration and run-out, which leads to a stable cutting edge and reproducible results in production. The 7° clearance and the 80° cutting geometry produce a predictable cutting force vector that helps maintain dimensional accuracy, while the 3.97 mm plate thickness contributes to mechanical rigidity during interrupted or heavy cuts. Durable cutting performance from a specialised grade The J740 grade is a Tungaloy-developed carbide composition optimised for turning, balancing wear resistance and toughness to preserve the cutting edge under varied conditions. Combined with the insert's single-sided chipbreaker, the design promotes effective chip control in many turning scenarios and reduces rework. For those less familiar with cutting grades: the term denotes the engineered microstructure and coating approach that determine how the insert resists abrasion and mechanical shock, which directly affects tool life and machining economy. Practical application and system considerations for shop-floor use The rhombic profile and the cylindrical hole with a single-side countersink (40°–60°) facilitate secure clamping and straightforward indexing in compatible external holders or boring bars. Typical system components include the ISO insert itself, a matched external holder or bar, an underlay/clamping set and replacement screws. For external and internal turning operations, selecting the correct chipbreaker and the J740 grade according to workpiece stability and material type delivers improved surface finish and higher productivity. The insert's characteristics make it suitable where process reliability and repeatability are priorities. For technical guidance on adapting the CCGT09T300 J740 insert to specific applications or to place an order, contact Metav Werkzeuge for consultancy and procurement assistance at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 6801305 SKU: 6801305-Tungaloy Manufacturer SKU: TUN6801305 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Size designation: 09 Plate form: rhombic Thickness: 3.97 mm Clearance angle: 7° Cutting angle: 80° Hole: with hole; cylindrical hole + single-side countersink (40°–60°) Facts Standard: ISO Application: Turning Chipbreaker: single-sided Grade: J740 Manufacturer: Tungaloy Design & special features Carbide grade J740 (Tungaloy cutting grade) Single-sided chipbreaker for controlled chip flow Rhombic geometry for versatile cutting angles Cylindrical hole with countersink for secure clamping Intended system: ISO insert, matching external holder/boring bar, underlay/clamping set, spare screws FAQ What types of turning is this insert suitable for? The CCGT09T300 J740 insert is designed for both external and internal turning and performs well where stable chip control and edge integrity are required. How does the J740 grade affect tool life? The J740 Tungaloy grade balances wear resistance and toughness, which helps maintain the cutting edge for longer periods under normal turning conditions. What does the single-sided chipbreaker mean in practical terms? A single-sided chipbreaker provides predictable chip formation on the active cutting edge, aiding evacuation and reducing the risk of chip entanglement during turning operations. How is the insert secured in the holder? The insert features a cylindrical hole with a single-side countersink (40°–60°) that enables positive clamping in compatible ISO holders and boring bars. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precision finishing, low cutting forces and ISO‑compatibility for consistent turning results; order via Metav Werkzeuge or consult our technical team for application support. CCGT 09T300 NS9530 CCGT turning insert — uncoated cermet, 80° geometry — Tungaloy The CCGT09T300 NS9530 is an ISO‑standard rhombic turning insert designed for finishing operations on steel with a low cutting‑force, high‑surface‑quality profile. ISO 09T300 rhombic insert, 80° cutting geometry Uncoated cermet grade NS9530 for finishing 7° relief angle for low cutting forces Cylindrical hole with 40°–60° countersink High‑precision finishing with low cutting forces The uncoated cermet grade NS9530 delivers a sharp cutting edge tailored to finishing passes on steel. As a finishing grade, it promotes low cutting forces and an improved surface finish, making it particularly effective for continuous cuts and small depths of cut. These material and geometry choices reduce the need for aggressive machining parameters and help to achieve tighter dimensional tolerances with less vibration, which in turn supports stable production runs and consistent component appearance. ISO compatibility and secure clamping for repeatable results Designed to the ISO 09T300 specification, compatibility with a holder is determined by form, relief angle, tolerance class, fastening, size and thickness. The rhombic shape with an included angle of 80° and a 7° relief requires a matching external holder or boring bar; the insert’s cylindrical hole with one‑sided countersink (40°–60°) ensures reproducible seating and secure clamping. A well‑matched toolholder assembly improves repeatability, reduces setup time and minimises the risk of poor seating that can affect surface quality and tool life. Productive application advice and material suitability This ISO‑format insert is optimised for turning applications where finishing of steel is required. The one‑sided chipbreaker supports stable chip formation during continuous feeds, while the 3.97 mm plate thickness and size 09 provide a balance between rigidity and accessibility in narrow or internal turning operations. Choose the cutting data and holder stability to match the fine‑cutting nature of the grade: shallow depths of cut and steady feed rates will exploit the insert’s strengths and help extend effective tooling intervals. For technical advice on selecting the right insert geometry and for supply of original Tungaloy components, contact Metav Werkzeuge: info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will advise on holder compatibility and process optimisation Technical data Article number: 6967210 Manufacturer SKU: TUN6967210 SKU: 6967210-Tungaloy Model series: ISO‑turning inserts Application: Turning ISO code: 09T300 Facts Size: 09 Plate thickness: 3.97 mm Relief angle: 7° Included geometry: 80° Hole style: cylindrical hole + one‑sided countersink (40°–60°) Special features Material: carbide Grade: uncoated cermet NS9530 Chipbreaker: one‑sided Shape: rhombic insert ISO‑standard design for external and internal turning Optimised for continuous cutting and small cuts Compatibility depends on holder form, tolerance, fastening and size FAQ What materials is this insert best suited for? The CCGT09T300 NS9530 is a finishing grade optimised for steel; the uncoated cermet NS9530 offers a sharp edge and low cutting forces for superior surface quality on steel components. How is holder compatibility determined? Compatibility is defined by form, relief angle, tolerance class, fastening, size and thickness; matching the holder to the insert’s ISO 09T300 geometry and the 7° relief ensures secure seating and repeatable clamping. Can this insert be used for internal turning? Yes — the rhombic shape and size 09 combined with a suitable boring bar make it appropriate for internal finishing where access and rigidity are adequate. What does the hole style mean for mounting? The cylindrical hole with a single‑sided countersink (40°–60°) provides positive seating and straightforward clamping, improving positional repeatability and reducing the risk of slippage under finishing cuts. Is the grade coated or uncoated, and what are the implications? The NS9530 grade is uncoated cermet; this emphasises a sharp edge and excellent surface finish in finishing passes, while coating is typically used for more abrasive or higher‑temperature operations. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 09T300 NS9530 Wendeplatten - Tungaloy
Optimise finishing operations with the combination of the uncoated cermet NS9530 for low cutting forces and the ISO rhombic 80° geometry with 7° relief; reliable compatibility with ISO holders supports predictable production results. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. CCGT 09T300 NS9530 Turning Insert (ISO 09T300) – Tungaloy A CCGT09T300 NS9530 is an ISO rhombic turning insert designed for finishing operations on steel, offering a sharp edge for continuous cuts and small depths of cut ISO rhombic 80° profile, 7° clearance Uncoated cermet grade NS9530 for fine finishing Cylindrical hole with single-sided countersink 40°–60° Compatible with ISO turning holders and adaptors Consistent fine surface finish with reduced cutting forces The combination of an uncoated cermet cutting material and a rhombic geometry delivers a finely honed edge that reduces friction and cutting forces, which in turn improves machining stability during finishing passes. Cermet is a composite of ceramic and metal that provides a sharp, wear-resistant edge ideal for continuous cutting on steel; the result is a reliably improved surface finish and lower tendency for built-up edge compared with some coated grades. For shops prioritising dimensional consistency and minimal rework, this insert supports predictable outcomes on medium to high-production finishing cycles. Seamless fit into ISO tool systems to shorten changeover times The ISO conformity of the insert simplifies selection of the matching holder: the ISO rhombic 80° seating angle and the specified mounting features allow correct clamping by standard external holders or boring bars. The insert’s mounting aperture—with a cylindrical hole plus a single-sided countersink (40°–60°)—ensures stable fixation and repeatable register, while the 3.97 mm plate thickness contributes to rigidity when used with appropriately matched underlays and clamping sets. These attributes reduce set-up variation and contribute to shorter tool-change intervals, supporting higher overall machine utilisation. Targeted productivity for finishing and small depth-of-cut applications Designed as a finishing grade, NS9530 is optimised for low cutting resistance and excellent edge retention during small material removals. The single-sided chipbreaker controls chip formation in continuous-cut scenarios, assisting reliable evacuation and consistent surface quality. The modest relief angle of 7° balances clearance and edge support for fine finishing, while the rhombic form provides flexibility for a range of turning tasks including external and internal operations. For production environments where repeatability and finish are decisive, the insert offers an economical path to steady, high-quality output. If further process data is required or to confirm holder compatibility for a specific application, technical consultation is available; practical assistance can be obtained from Metav Werkzeuge by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930. This aids correct selection of the matching holder, clamping set and replacement screws for seamless integration into existing tool systems. Contact Metav Werkzeuge for application advice and to reserve Tungaloy NS9530 finishing inserts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 6967260 Manufacturer article number: 6967260 Manufacturer SKU: TUN6967260 SKU: 6967260-Tungaloy Model series: ISO-Drehwendeschneidplatten WPL designation: CCGT09T300 Facts Size: 09 Shape angle: 80° Clearance (relief): 7° Thickness: 3.97 mm Hole: with cylindrical hole + single-sided countersink (40°–60°) Special features Uncoated cermet grade NS9530 Single-sided chipbreaker Application: Turning Plate shape: rhombic FAQ What turning tasks is this insert most suitable for? The CCGT09T300 NS9530 Tungaloy turning insert is intended for finishing operations on steel, especially continuous cuts and small depths of cut where a fine surface finish is required. Which materials can be machined with this grade? This uncoated cermet grade NS9530 is designed specifically for finishing on steel; its properties favour low cutting forces and high surface quality on general steel grades. How should the insert be mounted in the holder? Mounting requires an ISO-compatible rhombic seat and a clamping system that matches the insert’s cylindrical hole with single-sided countersink; the insert’s geometry and hole style provide secure and repeatable fixation. What advantages does the uncoated cermet NS9530 offer over coated grades? The NS9530 cermet offers a sharper initial cutting edge and reduced tendency for built-up edge in finishing applications, resulting in superior surface quality during continuous finishing passes. Is the insert suitable for internal as well as external turning? Yes; the rhombic form and geometry make the insert adaptable for both external and internal turning when paired with appropriate ISO holders and bar tooling. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 SH7025 Wendeplatten - Tungaloy
Take advantage of the SH7025 coated carbide grade and the 7° clearance combined with the rhombic 80° geometry for reliable turning under variable engagement; order directly via Metav Werkzeuge or consult our specialists for application advice. CCGT09T300 SH7025 – CCGT 09T300 indexable insert for turning by Tungaloy The CCGT09T300 SH7025 is an ISO-standard rhombic indexable insert for external and internal turning, designed for stable cutting edges and versatile use in assemblies with ISO match holders. ISO CCGT 09T300 geometry SH7025 coated carbide grade 7° clearance angle for versatility Cylindrical hole with 40°–60° countersink Reliable cutting under variable engagement The combination of a coated carbide grade and compact geometry provides consistent performance where cutting conditions change frequently. The SH7025 grade is formulated for toughness and edge stability, which reduces the need for frequent regrinding and supports longer productive tool life. As a consequence, machining cycles benefit from fewer interruptions and steadier surface finish, helping to maintain workflow efficiency in small and medium batch production. Secure clamping and ISO compatibility for fast tool changes Compatibility with ISO toolholders is determined by form, clearance angle, tolerance class, fastening method, size and thickness; the ISO-standard designation ensures straightforward integration into existing tool systems. The cylindrical hole with one-sided countersink (40°–60°) provides repeatable seating and secure clamping, reducing micro-movements at the cutting edge. This mechanical reliability shortens set-up time and minimises the risk of vibration-related tool wear during turning operations. Geometry and chip control for cleaner turning The rhombic shape with an 80° angle and the single-sided chipbreaker produce predictable chip flow for a wide range of feeds and depths. The chipbreaker design aids in fragmenting chips and directing them away from the cutting zone, improving surface quality and reducing manual chip handling. With a 3.97 mm thickness and size 09, the insert balances stiffness and accessibility, making it suitable for confined tool positions and varied turning tasks without sacrificing stability. Practical selection guidance for everyday workshop use For turning applications—both external and internal—the SH7025 grade is recommended where toughness and a durable cutting edge are priorities, especially in smaller tools or where engagement conditions vary. The insert functions as part of a system: ISO indexable insert, matching outer holder or boring bar, a shim/clamping set and spare screws. Selecting the correct chipbreaker and holder rigidity will directly influence productivity and surface finish, translating technical features into measurable production gains. For SH7025 performance and ISO compatibility, contact Metav Werkzeuge for ordering and tailored application advice via info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants are available to support selection and delivery. Technical data Article number: 6967405 SKU: 6967405-Tungaloy Designation: CCGT09T300 Model series: ISO indexable turning inserts Material: carbide Numerical data Size: 09 Thickness: 3.97 mm Corner angle: 80° Clearance angle: 7° Countersink angle: 40°–60° Special features Rhombic plate form Cylindrical hole with single-sided countersink Single-sided chipbreaker Coated grade SH7025 Intended application: turning ISO-standard insert, compatible with ISO holders System components: insert, outer holder/boring bar, shim/clamping set, spare screws FAQ What materials is this insert suitable for? The CCGT09T300 SH7025 Tungaloy insert is a coated carbide grade designed for a broad range of steels and general turning tasks where toughness and edge stability are needed. How does the SH7025 coating benefit machining? SH7025 offers enhanced edge toughness and wear resistance; on the CCGT09T300 this results in longer edge life and consistent surface finishes under varying engagement. Can the insert be used for both internal and external turning? Yes. The insert geometry and ISO compatibility make the CCGT09T300 SH7025 suitable for both external and internal turning operations when paired with an appropriate holder. What does the cylindrical hole with countersink provide? The cylindrical hole with a 40°–60° countersink ensures secure, repeatable clamping and reduces the chance of insert movement during cutting, improving machining stability. How to choose the right chipbreaker for my application? Select a chipbreaker that matches material, feed and depth of cut; the single-sided chipbreaker on this insert is optimised for controlled chip formation in common turning scenarios with variable engagement. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 SH7025 Wendeplatten - Tungaloy
Benefit from stable cutting edges and ISO conformity to secure consistent cycle times and predictable tool life; the coated carbide grade SH7025 ensures durable performance even with smaller holders and varying engagement conditions. Order the CCGT09T300 directly via Metav Werkzeuge or consult our experts for holder compatibility and rapid supply. CCGT 09T300 SH7025 — ISO indexable turning insert for Drehen, Tungaloy CCGT 09T300 SH7025 is an ISO-standard rhombic indexable insert designed for external and internal turning applications, offering a robust cutting edge for small tools and variable engagement conditions. ISO rhombic insert, size 09 Coated carbide grade SH7025 7° relief angle for versatile cutting Cylindrical hole with 40°–60° countersink Consistent edge stability for reliable production The CCGT09T300 SH7025 insert is engineered for repeatable performance under changing cutting conditions. The coated carbide grade SH7025 provides a tough, cutting-edge-stable substrate that reduces unexpected edge breakdown and supports longer tool cycles. For production environments where set-up changes or small-diameter holders are common, the insert’s geometry and coating combine to maintain part quality and reduce unscheduled tool changes, improving overall throughput and process reliability. Fast setup and clear compatibility criteria Compatibility with toolholders is determined by form, relief angle, tolerance class, clamping method, size and thickness. The rhombic 09 shape and the 7° relief simplify selection for common external and internal turning holders, while the central cylindrical hole with single-side countersink (40°–60°) ensures secure clamping and consistent seating. Clear dimensional standards reduce setup time and the need for trial-and-error, translating into less machine downtime and faster job changeovers. Material behaviour and when to choose this grade The SH7025 coating and cemented carbide substrate are aimed at demanding turning tasks where edge stability under varying engagement is required. The insert performs well when intermittent cuts or small overhangs place fluctuating loads on the cutting edge. The combination of coating and substrate hardness balances wear resistance with toughness, making the insert appropriate for mixed-production environments where a single grade must cover several workpiece materials and cutting conditions. Practical application advice for workshop and production floors Designed for both external and internal turning, the insert’s 80° included angle and 3.97 mm thickness give a robust footprint for stabilising the cutting process, particularly in smaller toolholders. The one-sided chipbreaker is suitable for general-purpose turning; selecting the correct chipbreaker and insert grade according to the workpiece material and machining strategy will maximise performance. For secure procurement and advice on holder matching, consult the product experts to ensure optimal process integration. Contact Metav Werkzeuge for fast supply and technical selection support on Tungaloy SH7025 inserts; reach us at info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations Technical data Article number: 6967444 SKU: 6967444-Tungaloy Manufacturer SKU: TUN6967444 Model series: ISO turning indexable inserts Material: cemented carbide Facts Relief angle: 7° Included angle: 80° Plate thickness: 3.97 mm Size: 09 Countersink angle: 40°–60° Special features ISO designation: CCGT09T300 Coating grade: SH7025 Plate form: rhombic Hole style: cylindrical hole + single-side countersink Chipbreaker: one-sided Typical application: turning (external and internal) FAQ What materials is this insert suitable for? The CCGT09T300 SH7025 insert from Tungaloy is intended for turning tasks that demand edge stability across a broad range of workpiece materials; the grade is optimised for situations with varying engagement and smaller toolholders. How does the SH7025 coating improve performance? The SH7025 coating increases cutting-edge robustness and wear resistance, helping to maintain consistent machining results and extend indexable insert life under fluctuating cutting conditions. What are the key dimensions and geometry of the insert? The insert is a rhombic size 09 with an 80° included angle, 3.97 mm thickness, a 7° relief and a cylindrical hole with a single-side countersink (40°–60°) for reliable clamping. Can this insert be used for internal turning as well as external turning? Yes, the design and ISO conformity of the insert make it suitable for both external and internal turning operations when the appropriate holder and cutting conditions are selected. How is compatibility with a toolholder determined? Compatibility is based on form, relief angle, tolerance class, clamping method, size and thickness; these criteria should be matched to the holder specification to ensure secure fixation and correct geometry during turning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 SH7025 Wendeplatten - Tungaloy
Take advantage of the combination of durable coated carbide, ISO compatibility and secure mounting for consistent turning results; order directly via Metav Werkzeuge or consult our technical team for application matching. CCGT 09T300 SH7025 — Turning insert by Tungaloy (ISO rhombic insert, 7° clearance) The CCGT09T300 SH7025 is an ISO-standard rhombic turning insert designed for versatile external and internal turning operations, offering a tough, edge-stable coated carbide grade for variable engagement conditions. Coated carbide grade SH7025 ISO rhombic insert size 09 7° clearance angle for smooth cutting Cylindrical hole with 40°–60° countersink Improve process stability with a tough, edge-stable grade The SH7025 coating combines toughness and reliable edge retention, making this insert well suited to turning tasks where engagement conditions change or where smaller tooling is used. As an ISO-standard rhombic insert, it delivers predictable geometry and repeatable cutting behaviour, which supports steady cycle times and consistent surface quality. The design reduces the risk of premature flank wear and helps maintain dimensional accuracy over multiple indexings, contributing to a measurable improvement in process reliability and fewer unplanned tool changes. Faster changeovers and secure clamping for minimal downtime The insert features a cylindrical hole with single-side countersink (40°–60°) that enables secure screw fastening to standard ISO holders. Compatibility with the holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness, so matching the insert to the correct clamping system ensures optimal seat contact and torque transmission. The result is reliable clamping, straightforward index changes and shorter tool-change cycles, which supports higher machine utilisation and reduced non-productive time. Versatile application for external and internal turning This rhombic geometry with an 80° included angle and a 7° clearance offers a balanced combination of strength and accessibility for a wide range of turning tasks. The single-sided chipbreaker provides controlled chip formation for common turning operations and is particularly effective when feed and engagement vary. The coated carbide composition is engineered to perform well under interrupted cuts and switching conditions typical of mixed-production environments, so the insert is a pragmatic choice for workshops seeking flexibility without compromising on tool life. Economical use and straightforward handling Thanks to the coated carbide grade and standardised ISO dimensions, the insert supports economical tooling strategies: predictable wear behaviour enables planned indexing, and the robust cutting edge reduces unexpected tool failures. The system concept comprises the ISO insert, a matching external holder or boring bar, a shim/clamp set and replacement screws, allowing components to be selected and replaced independently to suit the application. This modular approach helps control stocking costs and simplifies maintenance procedures while maintaining production consistency. For tailored application advice or to request availability of the Tungaloy CCGT09T300 SH7025 insert, please contact Metav Werkzeuge by e-mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants will assist with holder compatibility and selection. Technical data Article number: 6967376 Manufacturer SKU: TUN6967376 SKU: 6967376-Tungaloy Material: Hartmetall Model series: ISO-Drehwendeschneidplatten Core specifications ISO designation: CCGT09T300 Insert designation without grade: CCGT09T300 Grade / coating: SH7025 Insert size: 09 Plate thickness: 3.97 mm Clearance angle: 7° Included angle: 80° Design and features Plate shape: rhombic Hole: with hole Hole style: cylindrical hole + single-side countersink (40°–60°) Chipbreaker: single-sided Intended application: Drehen (turning) FAQ What materials is this insert intended for? The SH7025 grade is a tough, edge-stable coated carbide formulated for general turning tasks; the CCGT09T300 SH7025 insert performs well in situations with varying engagement and in smaller tooling set-ups, offering reliable cutting-edge stability across common ferrous applications. How is holder compatibility ensured? Compatibility depends on the insert form, clearance angle, tolerance class, fastening method, size and thickness; matching the CCGT09T300 to an ISO-compatible holder or boring bar with the correct clamping hardware ensures secure seating and repeatable performance. What does the single-sided chipbreaker mean in practice? A single-sided chipbreaker provides controlled chip formation on one primary cutting edge, improving chip control under typical turning feeds and aiding evacuations in external and internal operations without adding complexity to the clamping system. Is the insert supplied with mounting hardware? The system comprises the ISO insert, a suitable external holder or boring bar, a shim/clamp set and replacement screws; the insert article is supplied as the cutting plate itself, while holders and fastening components are selected separately to match the application. How does the SH7025 coating contribute to economy? The SH7025 coating improves wear resistance and edge robustness, which prolongs index intervals and reduces unplanned tool changes; the predictable life cycle of the insert helps to lower overall tooling costs through more efficient planning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T300 SH725 Wendeplatten - Tungaloy
Take advantage of a robust combination of coated carbide SH725 and ISO‑standard geometry for consistent machining results and longer tool life; the rhombic 80° form with a 7° relief guarantees predictable engagement and easy holder compatibility. Order the CCGT09T300 SH725 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. CCGT 09T300 SH725 ISO turning insert (rhombic, 80°) – Tungaloy CCGT 09T300 SH725 is an ISO‑standard turning insert designed for external and internal turning applications, offering a tough, edge‑stable coated carbide grade for variable engagement conditions and smaller tooling setups Durable SH725 coated carbide grade ISO CCGT09T300 rhombic 80° geometry Cylindrical hole with single-sided countersink Suitable for external and internal turning Reliability and performance for diverse turning tasks The CCGT09T300 SH725 insert delivers a balance of wear resistance and edge toughness through its coated carbide construction, making it suitable for interrupted cuts and changing engagement conditions where smaller tool bodies are used. The SH725 grade was selected to favour stable chipbreak and consistent edge life, which translates into fewer indexings and reduced spindle downtime. For production environments, this means improved process repeatability and lower tooling handling effort compared with uncoated or softer grades. Precision fit and geometry for secure clamping The insert follows ISO specifications with a rhombic shape and an included angle of 80°, combined with a 7° relief that defines how the insert meets the workpiece. A thickness of 3.97 mm and the 09 size ensure compatibility with a wide range of ISO holders, while the cylindrical hole with a one‑sided countersink (40°–60°) simplifies clamping and alignment in standard toolholders. Clearances, tolerance class, and screw or clamp design determine the final fit; matching these parameters avoids chatter and secures cutting stability. Productivity through controlled chip formation and longevity The one‑sided chipbreaker geometry promotes predictable chip flow and reduces the risk of recutting, which supports higher cutting rates and more consistent surface finishes on workpieces. Combined with the SH725 coating, the insert resists abrasive wear while retaining a robust cutting edge, enhancing tool life and lowering per‑part tooling cost. In practical terms, less frequent insert changes and steady cutting behaviour increase throughput and free up machine time for additional operations. Practical selection and system integration guidance Select the chipbreaker and grade to match workpiece material and machining stability: the tougher SH725 grade is advantageous for mixed engagement and smaller cutters, while lighter cuts may permit more aggressive grades elsewhere. The insert functions as part of a system—an ISO turning insert, a compatible holder, a backing washer or clamp set, and replacement screws—so ensure holder form and tolerance match the insert’s geometry. For customers unfamiliar with specific holder matches, technical consultation helps avoid mismatched combinations and ensures optimal cutting parameters. Contact Metav Werkzeuge for tailored application advice and to request the Tungaloy CCGT09T300 SH725 ISO turning insert (SKU TUN6838671) for immediate supply and integration support Technical data Article number: 6838671-Tungaloy Manufacturer SKU: TUN6838671 Manufacturer article number: 6838671 Model series: ISO turning inserts Material: Coated carbide Grade: SH725 Insert designation: CCGT09T300 Core specifications Size: 09 Thickness: 3.97 mm Relief angle: 7° Included angle: 80° Hole style: with hole (cylindrical + one-sided countersink 40°–60°) Special features Rhombic insert shape One-sided chipbreaker ISO‑standardised geometry Suitable for external and internal turning Compatible holder depends on form, clearance, tolerance, clamping, size and thickness Designed for stable chip formation and variable engagement conditions FAQ What materials is this insert suited for? The Tungaloy CCGT09T300 SH725 ISO turning insert is formulated for versatile use; the SH725 grade supports a broad workpiece range and is especially useful where edge stability is required under variable engagement. How does the hole and countersink affect clamping? A cylindrical hole with a single‑sided countersink (40°–60°) on the CCGT09T300 insert enables secure seating in compatible holders and simplifies axial positioning when using standard ISO clamping methods. Can this insert be used for both external and internal turning? Yes, the rhombic 80° geometry and 09 size make the insert suitable for both external and internal turning operations when paired with an appropriate holder and clamping set. What should be considered when selecting a holder for this insert? Ensure holder compatibility with the insert’s size, thickness and relief angle; the clamping method, tolerance class and form determine correct seating and stable cutting performance for the CCGT09T300 SH725 insert. Is technical support available for tool selection and cutting data? Technical assistance is available to match the Tungaloy CCGT09T300 SH725 insert to specific applications and holders and to recommend cutting data for improved productivity Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com