VNMG 160412 T505 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide grade optimised for economical cast iron machining and a 35° geometry that supports stable turning operations; order the insert directly via Metav Werkzeuge or consult our technical advisers for application-specific recommendations. VNMG160412 T505 — ISO turning insert for cast iron, Tungaloy The VNMG160412 T505 is an ISO-standard indexable insert designed for external and internal turning, calibrated for efficient machining of cast iron with a robust, CVD-coated carbide grade. CVD-coated carbide for durability Optimised for cast iron machining Double-sided chipbreaker for versatile use ISO VNMG160412 35° geometry Engineered for consistent cast iron performance The insert is manufactured from CVD-coated carbide, a coating process that deposits a hard, wear-resistant layer over the cemented carbide substrate to extend tool life and maintain edge stability under interrupted cuts. This grade, identified as T505, is targeted at the economic machining of cast iron, offering a balance between tool life and cutting-speed capability. For production environments where predictable reorder cycles and consistent quality are priorities, the combination of coating and carbide substrate reduces tool changes and keeps cycle times steady. Geometry and dimensions that support precision turning With a 35° approach angle, a 1.2 mm nose radius and a 4.76 mm thickness, the insert provides a favourable mix of strength and finishing capability. The rhombic shape and 0° clearance angle mean that the insert seats securely in ISO-compatible holders; compatibility depends on the holder’s form, relief geometry, tolerance class, clamping method, size and thickness. The insert is supplied with a cylindrical hole for positive locating and clamping stability. These dimensional details help engineers and purchasing managers verify fitment quickly and avoid downtime caused by mismatched tooling. Chip control and process efficiency for shop-floor productivity This insert features a double-sided chipbreaker, which improves chip formation and evacuation when turning varied cast-iron grades. Better chip control reduces the risk of burrs, machine interruptions and secondary operations, thereby supporting continuous production. As the insert is double-sided and indexable, each corner provides an additional cutting edge, increasing yield per insert and contributing to lower tooling cost per part. The overall effect is a pragmatic improvement in throughput while maintaining surface quality. Practical compatibility and selection guidance The insert belongs to the ISO turning insert family and fits any ISO-standard toolholder that matches the VNMG form and the specified dimensions. When selecting a chipbreaker and grade, consider the workpiece stability, expected interruptions in the cut and the desired cutting speed; the T505 grade is suited to many cast-iron turning tasks but may be paired with different holders or clamping sets depending on machine rigidity. If requirements include specific surface finish targets or higher feed rates, consult compatibility parameters—form, clearance, tolerance and clamping—to ensure the holder and insert work as a system. For detailed application advice or to secure the VNMG160412 T505 CVD-coated insert from Tungaloy for your turning processes, contact Metav Werkzeuge—info@metav-werkzeuge.com or call +49 2822 7131930—and obtain tailored guidance on holder matching and process setup. Technical data Article number: 6831802 Manufacturer SKU: TUN6831802 SKU: 6831802-Tungaloy Model series: ISO turning inserts Designation: VNMG160412 Brand: Tungaloy Facts Nose radius: 1.2 mm Thickness: 4.76 mm Insert size: 16 mm Approach angle: 35° Clearance angle: 0° Special features CVD-coated carbide Double-sided chipbreaker For turning (external and internal) Rhombic insert form With cylindrical hole for clamping Suited for cast iron machining ISO-compatible insert dimensions FAQ What materials is this insert designed for? The VNMG160412 T505 insert is specified for economical machining of cast iron; the T505 CVD-coated carbide grade provides wear resistance suited to typical cast-iron turning applications. How many cutting edges are available per insert? This rhombic, double-sided insert provides multiple usable edges; it is indexable so each side can be rotated and reused until the edges reach wear limits, increasing yield per insert. Which holders are compatible with this ISO insert? Compatibility depends on holder form, relief/clearance geometry, tolerance class, clamping method, size and thickness; the VNMG160412 follows ISO standards and fits holders designed for VNMG inserts when dimensions align. What does the 35° geometry mean for machining? A 35° approach angle balances cutting forces and surface finish, reducing radial load while enabling effective chip formation for cast-iron turning operations. Is the insert supplied ready for mounting? The insert is supplied with a cylindrical hole for positive locating; matching clamping hardware and the correct torque specification are required for safe and repeatable mounting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T5105 Wendeplatten - Tungaloy
Take advantage of the CVD-coated cemented carbide grade T5105 for sustained high-speed machining of cast iron and the double-sided chipbreaker for reliable chip control; the ISO-standard geometry and clear dimensions ensure straightforward holder compatibility. Order the VNMG160412 T5105 insert directly via Metav Werkzeuge or ask our consultants if needed. VNMG 160412 T5105 indexable turning insert for turning – Tungaloy A VNMG160412 T5105 indexable insert engineered for high-speed turning of cast iron under stable machining conditions, compatible with ISO-standard holders. CVD-coated carbide grade T5105 for high-speed use Designed for efficient cast iron turning Double-sided chipbreaker for stable chip control ISO-standard VNMG 160412 geometry for easy fit Consistent cutting performance and wear resistance The combination of a CVD-coated surface and a cemented carbide substrate delivers enhanced wear resistance under elevated cutting speeds. This grade is formulated to keep flank and crater wear low during continuous turning operations on cast iron, so cycle times remain predictable and tool changes are reduced. The coating reduces built-up edge formation and preserves the cutting edge, providing a measurable contribution to process stability and cost-efficiency in production environments. Geometry that ensures repeatable results and simple set-up With an ISO-compliant VNMG 160412 form, the insert offers clear dimensional references: 35° lead angle, 0° clearance angle, edge radius 1.2 mm and a 4.76 mm thickness, all of which affect chip flow and surface finish. The rhombic shape and cylindrical hole enable secure clamping in standard external holders or boring bars; tolerance and fixing are determined by form, relief, and thickness, ensuring repeatable seating and concentricity. Choosing the correct holder and tightening torque completes the system for reliable machining. Practical advantages in everyday turning applications The dual-sided chipbreaker supports controlled chip formation and evacuation, which reduces interruptions and improves operator safety in long production runs. The insert is particularly suited to stable setups and finishing or light roughing where surface quality matters; when combined with the correct coolant strategy and holder rigidity, the double-sided chipbreaker contributes to consistent surface integrity. For repairs, re-indexing restores geometry quickly, helping to keep machine uptime high and inventory manageable. For process-critical turning, specify the Tungaloy VNMG160412 T5105 for cast iron operations and contact Metav Werkzeuge for holder matching and application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6852943 SKU: 6852943-Tungaloy Manufacturer SKU: TUN6852943 Facts Lead angle: 35° Clearance angle: 0° Edge radius: 1.2 mm Thickness: 4.76 mm Plate size: 16 mm Special features Shape: rhombic Hole: cylindrical hole Chipbreaker: double-sided Grade: T5105 (CVD-coated) Material: cemented carbide Application: Turning Model series: ISO indexable turning inserts Insert designation: VNMG160412 FAQ What materials is this insert suited for? The VNMG160412 T5105 insert from Tungaloy is optimised for cast iron turning under stable, high-speed conditions and performs well where consistent chip control is required. Can the VNMG160412 be used for internal and external turning? Yes, the VNMG160412 geometry and the cylindrical hole permit use in both external holders and appropriate boring bars for internal turning with the correct holder selection. How does the T5105 grade affect tool life? The T5105 CVD-coated grade increases wear resistance at higher cutting speeds, helping to extend effective tool life and maintain surface finish over longer runs. What influence does the 1.2 mm edge radius have on the component finish? An edge radius of 1.2 mm balances robustness and surface quality: it smooths edge contact and can improve finish while maintaining strength for light turning passes. Is the insert compatible with standard ISO VNMG holders? The insert follows ISO VNMG 160412 dimensions; compatibility is determined by form, relief angle, tolerance class, fastening and thickness, so matching a standard VNMG holder is typically straightforward. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T5115 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide grade T5115 and the ISO VNMG geometry for consistent, cost-effective turning of cast iron; the insert’s balanced wear resistance and edge stability support steady production. Order components and matching holders through Metav Werkzeuge or consult the technical team for holder compatibility and cutting-parameter recommendations. VNMG160412 T5115 – ISO rhombic turning insert, CVD-coated, Tungaloy VNMG160412 T5115 is a rhombic, ISO-indexable insert for precision turning applications, designed as a universal grade for cast iron machining CVD-coated carbide grade T5115 Universal grade for cast iron machining ISO VNMG 160412 rhombic insert 35° lead angle, 1.2 mm corner radius Consistent wear control for productive cast iron turning The T5115 grade combines a CVD-coated surface with a robust carbide substrate to deliver a practical balance between wear resistance and cutting-edge stability. This composition supports longer in-cut durations and predictable tool life in recurring turning tasks. The coating reduces built-up edge and improves thermal resistance, which in turn helps maintain surface finish and dimensional stability during series production of cast iron components. Fast set-up and reliable holder compatibility The ISO VNMG160412 geometry and the rhombic plate form ensure straightforward interchangeability with standard ISO external holders. The insert is supplied with a cylindrical hole, a plate thickness of 4.76 mm and a defined relief angle of 0°, which simplifies clamping and repeatable positioning. The 35° lead angle and 1.2 mm corner radius support versatile turning operations from finishing to light roughing while keeping fixture changeover times to a minimum. Stable chip formation and economical productivity Equipped with a double-sided chipbreaker, the insert promotes predictable chip control and extends the number of indexable edges per insert, improving cost efficiency per component. The universal design makes the grade suitable for a broad range of grey and ductile cast irons, helping to reduce tool inventory while delivering consistent surface quality. For production environments seeking process stability and reduced downtime, this insert supports repeatable results and efficient tool utilisation. For application advice, holder matching and availability contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to specify the VNMG160412 T5115 and receive tailored recommendations from the technical team Technical data Article number: 6850344 Manufacturer SKU: TUN6850344 Metav SKU: 6850344-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Carbide Grade/coating: T5115 Intended use: Turning Core specifications ISO designation: 160412 Insert size: 16 mm Plate thickness: 4.76 mm Corner radius: 1.2 mm Lead angle: 35° Relief angle: 0° Design & features Plate form: Rhombic (VNMG) Hole: With cylindrical hole Chipbreaker: Double-sided Schneidstofftyp: CVD-coated carbide Application focus: Cast iron machining FAQ What materials is this insert best suited for? The VNMG160412 T5115 insert is formulated as a universal grade for cast iron, offering a balanced combination of wear resistance and edge stability for grey and ductile cast-iron turning. Is the insert compatible with standard ISO VNMG holders? Yes, the insert follows the ISO VNMG160412 specification and is compatible with standard external holders designed for VNMG inserts, provided the holder matches form, clearance angle and thickness. How does the T5115 coating benefit production? The CVD-coated T5115 grade improves thermal resistance and reduces built-up edge, which helps maintain consistent surface finish and extends effective in-service time per edge on cast iron. How many usable edges does the insert provide? The insert features a double-sided chipbreaker, enabling multiple indexable cutting edges and thereby increasing the number of usable positions before replacement is required. What are the key geometry details to check for holder selection? Confirm ISO designation 160412, a 1.2 mm corner radius and the 35° lead angle; also ensure the holder accepts a rhombic VNMG plate with a cylindrical hole for secure clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T5125 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide T5125 for durable performance in interrupted cuts and the rhombic 35° geometry for stable turning; the combination ensures reliable chip control and consistent tool life in cast-iron applications. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. VNMG160412 160412 T5125 VNMG indexable insert for turning — Tungaloy VNMG160412 T5125 Tungaloy indexable insert for ISO-compliant turning applications, optimised for interrupted cuts and less-stable machining conditions CVD-coated grade T5125 for cast iron Designed for interrupted cuts and instability Rhombic 35° geometry for stable engagement 1.2 mm corner radius with cylindrical hole Durable grade for challenging cast-iron work The CVD-coated carbide grade T5125 delivers a tougher substrate that resists chipping under interrupted cutting conditions. That increased toughness translates into fewer insert failures and more predictable machining cycles when working with cast iron, even where vibration or less rigid set-ups are a factor. The specification of a dedicated machining grade means the insert supports steady productivity and reduces the risk of scrap parts from sudden edge breakouts. Stable geometry and exact fit for repeatable results ISO conformity simplifies tool selection: the insert’s rhombic geometry and 35° cutting angle produce a secure cutting engagement that supports consistent surface finish and dimensional control. The format includes a cylindrical hole for positive clamping and a 0° relief angle, while the 16 mm inscribed size and 1.2 mm corner radius ensure predictable edge strength. Compatibility with holders is determined by form, relief angle, tolerance class, clamping method, size and thickness; matching these parameters avoids runout and facilitates quick, repeatable tool changes. Practical economy through chip control and uptime The double-sided chipbreaker layout offers economical use of each indexable face and improved chip formation across a range of cutting conditions. By combining a robust substrate with a dedicated chip control geometry, the insert supports longer effective tool life and reduced downtime for index changes. For production environments, the result is increased throughput and lower cost per part without compromising process stability. System considerations and typical applications The insert is intended for external and internal turning within an ISO-based system: an appropriate external holder or boring bar, an underlay/clamping kit and replacement screws form the complete set-up. The grade’s emphasis on interrupted cuts and less-stable conditions means the part is particularly suited to cast-iron components or operations where suboptimal rigidity is expected. For routine planning, specify the chipbreaker and grade to match the workpiece material, machining strategy and machine stability to obtain the best balance of performance and economy. Contact Metav Werkzeuge today for tailored recommendations on Tungaloy turning solutions, including availability of the VNMG160412 T5125 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for application-specific guidance Technical Data Article number: 6852945 SKU: 6852945-Tungaloy Manufacturer SKU: TUN6852945 Model series: ISO-Drehwendeschneidplatten Manufacturer: Tungaloy Facts Inscribed size: 16 mm Corner radius: 1.2 mm Thickness: 4.76 mm Cutting angle: 35° Relief angle: 0° ISO designation: 160412 Special features CVD-coated carbide, grade T5125 Double-sided chipbreaker Rhombic plate shape With cylindrical hole for positive clamping Suitable for turning; optimised for cast iron and interrupted cuts System: ISO insert, compatible with matching holders, underlay/clamping set and replacement screws FAQ Is this insert suitable for cast-iron machining? Yes. The VNMG160412 T5125 indexable insert is a CVD-coated carbide grade developed for cast-iron applications, especially where interrupted cuts or less stable conditions occur. How is compatibility with holders determined? Compatibility depends on form, relief angle, tolerance class, clamping method, size and thickness; the VNMG160412 has a 16 mm inscribed size, 4.76 mm thickness and 0° relief angle and requires an ISO-compatible holder with matching specifications. What advantages does the T5125 grade provide? Grade T5125 offers enhanced toughness and wear resistance, improving resistance to chipping during interrupted cutting and contributing to longer, more reliable tool life for demanding turning operations. What is the function of the double-sided chipbreaker? The double-sided chipbreaker provides controlled chip formation across different cutting conditions and allows economical use of both cutting edges before indexing, reducing downtime and consumable costs. Which accessories complete the tool system for this insert? A suitable external holder or boring bar, an underlay/clamping kit and replacement screws form the complete ISO-based system for safe and repeatable operation with this insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T5125 Wendeplatten - Tungaloy
Take advantage of the combination of a CVD-coated carbide substrate and a robust 1.2 mm corner radius to ensure stable performance in interrupted cuts on cast iron; the insert’s ISO conformity and rhombic 35° geometry simplify integration into existing turning systems. Order the VNMG160412 T5125 turning insert directly via Metav Werkzeuge or consult our specialists for application advice. VNMG 160412 T5125 VNMG turning insert for turning — Tungaloy The VNMG160412 T5125 is an ISO-standard indexable turning insert designed for external and internal turning, optimised for cast iron and interrupted-cut conditions. CVD-coated carbide grade T5125 Optimised for cast iron and interrupted cuts ISO VNMG 160412 rhombic 35° geometry Double-sided insert with cylindrical hole Reliable chip control and prolonged tool life for cast iron The CVD-coated substrate combined with the T5125 grade delivers a balance of toughness and wear resistance that is particularly suited to machining cast iron under unstable conditions. The double-sided chipbreaker promotes predictable chip flow and reduces the risk of chip clogging, while the 1.2 mm corner radius increases edge strength for interrupted cuts. These design choices reduce unscheduled stoppages and contribute to a more consistent surface finish, thereby improving process reliability and overall productivity. Quick integration into ISO-compatible turning systems Conformity to the ISO VNMG 160412 form ensures straightforward compatibility with standard clamping systems. Compatibility is determined by form, clearance, tolerance class, fastening method, size and thickness; the insert’s rhombic 35° geometry and 0° clearance angle allow selection of suitable external or internal holders with minimal adaptation. The insert is supplied as a system element: indexable insert, matching holder or boring bar, shim/clamping set and replacement screws are recommended to complete the toolset and secure repeatable torque and positioning. Stable performance in interrupted cutting and less rigid set-ups The material combination of a tough carbide substrate and CVD coating is engineered to withstand shock loading typical for interrupted cuts. This results in fewer edge chipping events and a predictable wear pattern, which supports longer in-service intervals and lower tooling costs per part. The insert’s design absorbs transient forces, which is an advantage when machining components on less rigid machines or when facing variable clamping conditions. Selection guidance to match process requirements Choose the chipbreaker and the T5125 grade in line with the workpiece material, machining strategy and machine rigidity; for external and internal turning, select holders that match the insert’s 4.76 mm thickness and 16 mm size to maintain correct seat geometry. The cylindrical hole provides consistent clamping and indexability for double-sided use, increasing effective cutting-edge count. Where higher finish is required, consider the edge radius implications: the 1.2 mm radius enhances strength but yields a recognisable influence on surface roughness versus smaller radii. For application-focused advice on using Tungaloy’s T5125 grade for cast-iron turning and to order the VNMG160412 insert (SKU TUN6850345), contact Metav Werkzeuge for tailored recommendations and availability. Technical data Article number: 6850345-Tungaloy Manufacturer SKU: TUN6850345 Manufacturer article number: 6850345 Manufacturer: Tungaloy Facts Corner radius: 1.2 mm Plate thickness: 4.76 mm Plate size: 16 mm Cutting edge angle: 35° Clearance angle: 0° Special features Material: carbide Grade: T5125 (CVD-coated) Plate form: rhombic (VNMG) Hole: with cylindrical hole Chipbreaker: double-sided Application: turning System: ISO-standard indexable insert FAQ What materials is this insert best suited to? The VNMG160412 T5125 insert is particularly suited to cast iron machining; the T5125 grade and CVD coating provide toughness and wear resistance for interrupted cuts. Can this insert be used for both external and internal turning? Yes, the rhombic VNMG form and ISO conformity allow use in both external holders and suitable boring bars for internal turning. How does the 1.2 mm corner radius affect machining? A 1.2 mm corner radius increases edge strength and improves durability under interrupted cutting, with a trade-off towards a slightly higher minimum surface roughness compared with finer radii. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T515 Wendeplatten - Tungaloy
VNMG160412 T515 Drehwendeschneidplatte von Tungaloy für Drehen Die VNMG160412 T515 ist eine ISO-genormte Wendeschneidplatte für wirtschaftliches Drehen von Gusseisen und robuste Serienbearbeitung. Wirtschaftliche Bearbeitung von Gusseisen mit T515 Doppelseitige Schneide für längere Einsatzzeit Zylindrisches Loch für präzise Befestigung ISO-genormt für einfache Holderkompatibilität Effiziente Zerspanung dank CVD-beschichtetem Hartmetall Die Wendeschneidplatte nutzt CVD-beschichtetes Hartmetall, was eine stabile Schneidkante und verbesserte Standzeit bei der Bearbeitung von Gusseisen bringt. Diese Kombination reduziert Rüstintervalle und senkt die Werkzeugkosten pro Werkstück. Fachlich erklärt: CVD steht für chemische Gasphasenbeschichtung, die dünne, feste Schichten erzeugt, welche Verschleiß und Adhäsion verringern. Präzise Integration in den Werkstattprozess ISO-genormte Abmessungen und die rhombische Plattenform erleichtern die Auswahl des passenden Außenhalteres; Form, Freiwinkel und Toleranzklasse sind entscheidend für die Kompatibilität. Das zylindrische Loch sorgt für wiederholgenaue Positionierung bei Wechseln, was Stillstandzeiten minimiert und die Prozessstabilität erhöht. Produktivität durch doppelseitiges Design und Eckenradius Das doppelseitige Design erlaubt zwei Schneidkanten pro Platte, was die Standzeit pro Einsatz optimiert. Der Eckenradius 1,2 mm bietet eine gute Balance aus Schneidstabilität und Oberflächengüte; größere Radien verringern Kantenausbrüche bei instabilen Schnitten, kleinere Radien verbessern die Maßgenauigkeit bei feinen Schnitten. Praxisnahe Anwendungsempfehlung und Zielgruppe Konzipiert ist die Platte für den Einsatz im CNC-Außen- und Innendrehen von Gusseisen in Serien- und Einzelfertigung. Anwender sind Fertigungsbetriebe und Lohnfertiger, die Wert auf zuverlässige Standzeiten und einfache Holdertauschbarkeit legen. Technische Beratung und die Auswahl passender Spanbrecher und Halter sollten an das Bearbeitungsbild angepasst werden. Für wirtschaftliche Gusseisen-Bearbeitung empfiehlt sich die VNMG160412 T515 von Tungaloy; technische Beratung und schnelle Verfügbarkeit beim Händler Metav Werkzeuge: info@metav-werkzeuge.com, +49 2822 7131930 Technische Daten Artikelnummer: 6747821 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VNMG160412 T515 Tungaloy-Wendeplatte Fakten Eckenradius: 1,2 mm Winkel: 35° Plattendicke: 4,76 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: T515 (CVD: chemische Gasphasenbeschichtung) Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch Spanbrecher: doppelseitig Schneidstofftyp: CVD-beschichtetes Hartmetall Einsatzgebiet: Drehen SKU Hersteller: TUN6747821 FAQ Welche Werkstoffe sind für die VNMG160412 T515 geeignet? Die VNMG160412 T515 von Tungaloy ist speziell für die wirtschaftliche Bearbeitung von Gusseisen ausgelegt; die Sorte T515 wurde für stabile Spanbildung und hohe Schnittgeschwindigkeiten optimiert. Wie wirkt sich die CVD-Beschichtung auf die Standzeit aus? Die CVD-Beschichtung reduziert Verschleiß und verbessert die Wärmebeständigkeit; dadurch erhöht sich die Standzeit und die Anzahl einsetzbarer Schneidkanten pro Platte. Ist die Platte mit gängigen Außenhaltern kompatibel? Ja, die Platte ist ISO-genormt und passt zu Haltern, die die Form, Freiwinkel, Befestigung und Dicke für VNMG-Platten unterstützen; das zylindrische Loch erleichtert die präzise Montage. Wann ist ein Wechsel der Schneidplatte empfehlenswert? Ein Wechsel empfiehlt sich bei erkennbaren Verschleißspuren an der Schneidkante, nach Verschlechterung der Oberflächengüte oder wenn erhöhte Schnittkräfte und Vibrationen auftreten. Welche Vorteile bietet das doppelseitige Design konkret? Das doppelseitige Design ermöglicht zwei nutzbare Schneidkanten pro Platte, was Werkzeugkosten pro Schneide reduziert und Rüstintervalle verlängert. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T6215 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide grade that delivers consistent wear resistance and reliable surface quality in turning operations, together with a 35° cutting angle and secure, ISO-compatible mounting for straightforward tool changes; order the insert directly via Metav Werkzeuge or consult our technical team for holder compatibility and cutting data. VNMG 160412 T6215 rhombic turning insert — CVD-coated carbide for stainless steels, 1.2 mm corner radius (Tungaloy) VNMG 160412 T6215 is a rhombic ISO insert designed for precision turning of stainless steels under stable to mildly interrupted conditions CVD-coated carbide for wear resistance Optimised for turning rostfreier Stahl Rhombic VNMG geometry, 35° cutting angle Cylindrical hole for secure mounting Long tool life and consistent surface quality through advanced coating The T6215 grade combines a CVD-coated carbide substrate with a microstructure tuned to resist abrasive wear during the machining of stainless steels. This results in a longer tool life and more predictable replacement intervals, which supports continuous production and reduces unscheduled downtime. The coating improves resistance to built-up edge formation on stainless alloys, so the insert maintains a stable cutting edge under prolonged contact and moderate feed rates. For applications that demand reproducible finishes, the enhanced wear performance translates directly into lower rework rates and more efficient use of machine time. ISO compatibility and mechanical stability simplify setup and changeover The insert follows ISO dimensions for rhombic turning inserts (VNMG 160412), ensuring compatibility provided the holder matches form, relief, tolerance class, fixation and thickness. Key dimensional data — size 16, thickness 4.76 mm, corner radius 1.2 mm and a 35° main cutting angle — make it straightforward to select a suitable external holder or boring bar. The cylindrical centre hole ensures reliable clamping and repeatable positioning, reducing indexing time when rotating or replacing the insert. Clear, standardised geometry helps workshops maintain process stability and simplifies inventory management across holder families. Application-focused performance for stable and lightly interrupted turning Engineered for general turning tasks, the insert’s double-sided chipbreaker design offers two usable cutting edges, improving cost-efficiency per edge. The moderate corner radius of 1.2 mm balances edge strength and surface finish, making the insert suitable for external and internal turning where both dimensional control and edge robustness are required. The grade performs best in stable cutting conditions or slight interruptions; selecting the appropriate chipbreaker and cutting data according to workpiece rigidity and machining strategy will yield optimal results. If holder selection or cutting-parameter tuning is necessary, technical guidance supports the transfer of the insert’s capabilities into measurable productivity gains. Contact Metav Werkzeuge for tailored advice on holders and cutting parameters for Tungaloy turning inserts — our specialists provide compatibility checks, cutting data and fast delivery from stock. Technical data Article number: 6903053 Manufacturer SKU: TUN6903053 Metav SKU: 6903053-Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Size (inscribed circle): 16 Thickness: 4.76 mm Corner radius: 1.2 mm Relief angle: 0° Cutting angle: 35° Special features Geometry: rhombic VNMG (VNMG160412) Centre hole: cylindrical Grade: T6215 Coating: CVD-coated carbide Chipbreaker: double-sided Application: turning (outer and inner turning compatibility depends on holder) FAQ What materials is this insert suited for? The VNMG 160412 T6215 insert is formulated for machining stainless steels and performs best under stable to slightly interrupted turning conditions. How many usable cutting edges does the insert provide? Thanks to the double-sided chipbreaker design, the insert offers multiple indexing positions to maximise edge utilisation before replacement. What dimensions must a compatible holder support? A holder must match the VNMG 160412 geometry, accommodate a 16 size inscribed circle and a 4.76 mm plate thickness, and provide secure clamping for the cylindrical centre hole. Is the T6215 grade suitable for interrupted cuts? The T6215 grade is wear-resistant and tolerates slight interruptions; for heavy interruption or unstable setups, a tougher geometry or different grade should be considered. How does the CVD coating benefit stainless steel turning? The CVD coating on the carbide substrate improves wear resistance and reduces built-up edge tendencies when machining stainless steels, enhancing surface finish consistency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide T6215 wear resistance, a 35° rhombic cutting geometry and precise ISO compatibility for reliable turning of rostfreier Stahl — order directly via Metav Werkzeuge or consult our specialists for application support. VNMG160412 T6215 Turning insert by Tungaloy — CVD-coated carbide, 35° VNMG160412 T6215 is an ISO-format indexable turning insert for external and internal turning, designed for stable to slightly interrupted cutting of rostfreier Stahl ISO 160412 rhombic insert, 35° geometry CVD-coated carbide T6215 for wear resistance Double-sided chipbreaker, cylindrical hole 1.2 mm corner radius, 4.76 mm thickness Increased process stability for demanding turning tasks The insert is built to deliver consistent cutting performance in production environments where repeatability matters. As an ISO-format indexable insert, compatibility with the toolholder is defined by form, clearance angle (0°), tolerance class, fastening method, size and thickness; this ensures the insert sits correctly and cutting parameters are reproducible. The 35° cutting geometry and rhombic shape provide a balanced approach between strength and accessibility, allowing secure engagement in external and internal turning. The CVD-coated carbide T6215 grade is optimised for abrasion resistance when machining rostfreier Stahl, reducing flank wear and maintaining dimensional accuracy over longer tool life. Controlled chips and improved surface finish through optimised chipbreaking Chip control is a key contributor to cycle time and part quality. The double-sided chipbreaker design and cylindrical locating hole enable stable chip formation under steady and slightly interrupted cuts, which results in fewer reworks and safer chip evacuation. Where surface quality is critical, the insert’s geometry minimises vibrations and supports consistent finishes, while the wear-resistant coating helps to preserve the cutting edge. These features combine to improve productivity and lower unit cost by reducing downtime for frequent insert changes. Simple integration into existing tooling systems and predictable handling Integration is straightforward: the system comprises the ISO indexable insert, a matching external holder or boring bar, a shim/clamp set and replacement screws. The insert’s 1.2 mm corner radius and 4.76 mm thickness provide mechanical robustness for typical turning operations, and the rhombic form factor with a cylindrical hole facilitates quick, repeatable clamping. Selection and setup are based on the workpiece material, machining type and machine stability; for rostfreier Stahl under stable conditions the T6215 grade is recommended. If additional process data or holder compatibility checks are required, technical assistance is available via Metav Werkzeuge to ensure the insert performs as intended in the production environment. Contact Metav Werkzeuge for application advice and availability of the Tungaloy VNMG160412 T6215 turning inserts — our technical team is available by email or phone to support selection and process parameters Technical data Article number: 6944989 Manufacturer SKU: TUN6944989 Metav SKU: 6944989-Tungaloy Brand: Tungaloy Facts ISO code: 160412 Cutting angle: 35° Corner radius: 1.2 mm Thickness: 4.76 mm Insert size: 16 mm Special features Material: carbide Grade/coating: T6215 (CVD-coated) Chipbreaker: double-sided Shape: rhombic Hole: with cylindrical hole Application: turning (external and internal) Recommended for: rostfreier Stahl under stable to slightly interrupted conditions FAQ What materials is this insert suitable for? The Tungaloy VNMG160412 T6215 insert is a wear-resistant grade intended primarily for machining rostfreier Stahl under stable to slightly interrupted cutting conditions. How is compatibility with a holder determined? Compatibility depends on insert form, clearance (favourite) angle (0°), tolerance class, fastening type, size and thickness; the VNMG160412 conforms to the ISO 160412 specification. What mounting features does the insert have? The insert has a cylindrical locating hole for secure clamping and is intended for use with a matching external holder or boring bar, shim/clamp set and replacement screws. How does the chipbreaker affect machining? The double-sided chipbreaker promotes predictable chip formation and evacuation, improving surface finish and reducing the likelihood of rework during turning. Is this an original Tungaloy product? Yes — the VNMG160412 T6215 is an original Tungaloy indexable turning insert (Article number 6944989 / SKU TUN6944989). Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T6215 Wendeplatten - Tungaloy
VNMG160412 T6215 Tungaloy-Wendeplatte – Drehen Die VNMG160412 T6215 Tungaloy-Wendeplatte ist eine ISO-genormte, rhombische Wendeschneidplatte mit CVD-Beschichtung, entwickelt für das zuverlässige Drehen von rostfreiem Stahl unter stabilen bis leicht unterbrochenen Bedingungen ISO-genormte rhombische Wendeschneidplatte CVD-beschichtetes Hartmetall für hohe Verschleißfestigkeit Geeignet für das Drehen von rostfreiem Stahl Eckenradius 1,2 mm, Winkel 35° Doppelseitiger Spanbrecher, zylindrisches Loch Langlebige Schneidkante für anspruchsvolle Werkstoffe Die Kombination aus Hartmetall-Substrat und CVD-Beschichtung sorgt für eine langlebige Schneidkante bei Bearbeitungen an rostfreiem Stahl. Die Sorte T6215 ist speziell auf verschleißarme Zerspanung ausgelegt und reduziert Werkzeugwechsel dank stabiler Standzeit. Durch die verschleißfeste Oberfläche bleiben Schnittkräfte konstanter, was zu reproduzierbaren Ergebnissen und besserer Oberflächenqualität führt. Vorteilhaft ist dabei die Eignung für stabile bis leicht unterbrochene Schnittbedingungen, wodurch die Platte in typischen Produktionsumgebungen zuverlässig eingesetzt werden kann. Passgenauigkeit und einfache Integration in Fertigungszellen Die ISO-Normierung und die rhombische Form ermöglichen eine unkomplizierte Integration in gängige Außenhalter und Bohrstangen. Die Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; die vorhandenen Merkmale wie zylindrisches Loch und Plattengröße 16 mm erleichtern die Auswahl des passenden Halters. Durch die normgerechte Auslegung wird die Montage schneller und Rüstzeiten sinken, was insbesondere in Serienfertigung und bei häufigen Werkzeugwechseln zu Produktivitätsvorteilen führt. Wirtschaftliche Nutzung durch doppelseitigen Einsatz Der doppelseitige Spanbrecher erlaubt den Wechsel auf eine zweite Schneide, bevor die Platte ausgetauscht werden muss, und erhöht damit die Wirtschaftlichkeit pro Plattenstück. Der Eckenradius 1,2 mm bietet eine gute Kombination aus Tragfähigkeit und Schnittstabilität, während der Winkel 35° die Schneidengeometrie für vielseitige Anwendungen optimiert. Insgesamt führt die Konstruktion der Platte zu reduzierten Rüstkosten und einem effizienten Einsatz in produktiven Bearbeitungsprozessen. Empfehlung: Die Tungaloy-Wendeplatte mit CVD-Beschichtung (Sorte T6215) bietet verlässliche Standzeit und Prozesssicherheit; Bezug und technische Beratung über Metav Werkzeuge, eMail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6944935 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten SKU: TUN6944935 Fakten Eckenradius: 1,2 mm Winkel: 35° Freiwinkel: 0° Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: CVD (Chemical Vapor Deposition) Sorte: T6215 Schneidstofftyp: CVD-beschichtetes Hartmetall Anwendung: Drehen Spanbrecher: doppelseitig Plattenform: rhombisch Lochstil: zylindrisches Loch Loch: mit Loch Modellserie: ISO-Drehwendeschneidplatten Einsatz der Sorte: verschleißfeste Sorte für das Drehen von rostfreiem Stahl unter stabilen bis leicht unterbrochenen Bedingungen FAQ Was bedeutet die Bezeichnung VNMG160412? Die Bezeichnung beschreibt eine rhombische Wendeschneidplatte (VNMG) in der Größe 16 mit Eckenradius 1,2 mm und der ISO-Codierung 160412; die VNMG160412 T6215 Tungaloy-Wendeplatte entspricht damit gängigen ISO-Normen für Halter und erlaubt einfache Auswahl kompatibler Außenhalter. Für welche Werkstoffe ist die Platte geeignet? Die Platte ist speziell für rostfreien Stahl ausgelegt; die T6215-Sorte mit CVD-Beschichtung bietet erhöhte Verschleißfestigkeit bei diesen Werkstoffen und ist für stabile bis leicht unterbrochene Bearbeitungsbedingungen konzipiert. Ist die Platte doppelseitig verwendbar? Ja, die Wendeschneidplatte verfügt über einen doppelseitigen Spanbrecher, wodurch beide Schneiden genutzt werden können und sich die Nutzungsdauer pro Platte erhöht. Wie stelle ich die Kompatibilität zum Halter sicher? Die Kompatibilität ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; für die VNMG160412 T6215 Tungaloy-Wendeplatte sind insbesondere die rhombische Form, das zylindrische Loch und die Plattengröße 16 mm entscheidend. Welche Vorteile bringt die CVD-Beschichtung? Die CVD-Beschichtung erhöht die Verschleißfestigkeit und trägt zu konstanter Schneidleistung bei; dadurch verbessern sich Standzeit und Oberflächenqualität bei der Bearbeitung anspruchsvoller Werkstoffe wie rostfreiem Stahl. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T6215 Wendeplatten - Tungaloy
VNMG 160412 T6215 Drehwendeschneidplatte von Tungaloy VNMG 160412 T6215 ist eine ISO-genormte Drehwendeschneidplatte für das Drehen von rostfreiem Stahl bei stabilen bis leicht unterbrochenen Schnitten VNMG-Form, rhombisch und mit zylindrischem Loch CVD-beschichtetes Hartmetall für lange Standzeit Für Außen- und Innendrehen geeignet Doppelseitiger Spanbrecher für flexible Einsatzmöglichkeiten Längere Standzeiten durch moderne Beschichtung Die T6215-Sorte kombiniert eine robuste CVD-Beschichtung mit hochwertigem Hartmetall, wodurch die Verschleißfestigkeit beim Drehen von rostfreiem Stahl deutlich steigt. Weniger Werkzeugwechsel bedeuten höhere Maschinenlaufzeiten und geringere Stillstandskosten. Durch die optimierte Schnittkante bleibt die Oberflächengüte konstant, was die Nachbearbeitung reduziert und die Prozesssicherheit in Serienfertigung erhöht. ISO-kompatible Bauform für präzise Wechsel Die Plattengröße und Geometrie folgen der ISO-Norm, sodass die VNMG160412 einfach in passgenaue Halter eingesetzt werden kann. Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke bestimmen die Kompatibilität; der Freiwinkel von 0° und die rhombische Plattenform sorgen für wiederholgenaue Aufspannung. Das spart Rüstzeit und vereinfacht die Lagerhaltung, weil standardisierte Platten in vielen Haltern eingesetzt werden können. Zielgruppe und typische Anwendungen Dieses Werkzeug richtet sich an Zerspanungsbetriebe, Lohnfertiger und industrielle Werkstätten, die rostfreien Stahl effizient bearbeiten wollen. Die Wendeplatte eignet sich insbesondere für stabile bis leicht unterbrochene Schnitte beim Außen- und Innendrehen; der doppelseitige Spanbrecher erlaubt flexible Einsatzparameter. Anwender profitieren von planbareren Standzeiten und konstanter Bauteilqualität. Empfehlung: Für produktive Bearbeitung von rostfreiem Stahl die VNMG 160412 T6215 von Tungaloy einsetzen und bei Bedarf technische Beratung über Metav Werkzeuge anfordern – E‑Mail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6944926 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Typ: VNMG160412 Hersteller SKU: TUN6944926 Daten Eckenradius: 1,2 mm Winkel: 35° Freiwinkel: 0° Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung / Sorte: T6215 Schneidstofftyp: CVD-beschichtet (chemische Dampfabscheidung) Plattenform: rhombisch Lochstil: zylindrisches Loch (mit Loch) Spanbrecher: doppelseitig Anwendung: Drehen Typische Einsatzgebiete: Außen- und Innendrehen FAQ Für welche Werkstoffe ist diese Wendeplatte geeignet? Die VNMG 160412 T6215 von Tungaloy ist speziell für das Drehen von rostfreiem Stahl ausgelegt; die CVD-Beschichtung und die Sorte T6215 bieten gute Verschleißfestigkeit und Spanbildung bei stabilen bis leicht unterbrochenen Schnitten. Wie beeinflusst die Freiwinkelgeometrie die Anwendung? Der Freiwinkel von 0° reduziert die Kantenpressung und sorgt für stabile Zerspanungsbedingungen bei rostfreiem Stahl; das führt zu gleichmäßigerer Standzeit und konstanter Oberflächengüte für die VNMG160412. Ist die Platte in Standardhalter einsetzbar? Ja, die VNMG160412 entspricht ISO‑Maßen; Form, Größe, Befestigung und Toleranzklasse müssen mit dem Halter übereinstimmen, wodurch ein schneller und wiederholgenauer Wechsel möglich ist. Welche Vorteile bietet die Sorte T6215? Die Sorte T6215 bietet hohe Verschleißfestigkeit und stabile Spanbildung beim Drehen von rostfreiem Stahl, was Standzeiten verlängert und die Produktivität erhöht. Wie wähle ich den passenden Spanbrecher? Der doppelseitige Spanbrecher dieser Platte erlaubt unterschiedliche Einstellmöglichkeiten; für feine Oberflächen werden engere Geometrien gewählt, für höhere Spanvolumina offenere Geometrien. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T6215 Wendeplatten - Tungaloy
VNMG160412 T6215 Wendeplatte zum Drehen von Tungaloy Die VNMG160412 T6215 ist eine ISO‑genormte Drehwendeschneidplatte für das effiziente Drehen von rostfreiem Stahl unter stabilen bis leicht unterbrochenen Schnittbedingungen. Hohe Verschleißfestigkeit durch CVD‑Beschichtung Optimale Spanbildung für rostfreie Stähle Doppelseitiger Spanbrecher für lange Standzeiten ISO‑Genormt, kompatibel zu Standardhaltern Rhombische Form mit zylindrischem Loch Materialqualität und Beschichtung sichern Standzeit Die Kombination aus CVD‑beschichtetem Hartmetall sorgt für deutlich verbesserte Verschleißfestigkeit und konstante Schneidkantenleistung bei der Bearbeitung von rostfreiem Stahl. Anwender profitieren von reduzierten Rüstzeiten, weil die Sorte speziell für anspruchsvolle Stähle ausgelegt wurde. Dies führt zu planbaren Standzeiten und geringeren Werkzeugkosten pro gefertigten Bauteil. Prozessstabilität und Oberflächengüte erhöhen Effizienz Durch den doppelseitigen Spanbrecher entsteht eine kontrollierte Spanform, die die Maschinenlaufzeit erhöht und die Oberfläche des Werkstücks verbessert. Bei stabilen oder leicht unterbrochenen Schnitten erlaubt die Geometrie zuverlässig konstante Schnittleistungen, was gerade in Serienfertigungen zu höherer Produktivität führt. Kompatibilität und Handhabung erleichtern Integration Die ISO‑Norm und die genauen Maße machen die Platte einfach austauschbar in gängigen Außenhaltern und Bohrstangen; die Passung hängt von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke ab. Anwender sollten beim Einbau auf passende Unterlagen und Ersatzschrauben achten, um die volle Leistung der Insert‑Lösung zu gewährleisten. Zielgruppe und typische Anwendungen Diese Wendeschneidplatte wurde für Zerspaner entwickelt, die rostfreie Stähle drehen und Wert auf Prozesssicherheit sowie konstante Ergebnisse legen. Geeignet ist sie für Werkstätten und Produktionslinien, die wirtschaftliche, wiederholgenaue Bearbeitung benötigen und von optimierter Spanbildung profitieren. Für langlebige Bearbeitung empfehlen wir die Tungaloy‑Sorte T6215; direkt verfügbar bei Metav Werkzeuge – bei Fragen eMail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6966285 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Hersteller SKU: TUN6966285 Zahlen Radius: 1.2 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Winkel: 35° Besonderheiten Sorte: T6215 Schneidstofftyp: CVD‑beschichtetes Hartmetall Anwendung: Drehen Spanbrecher: doppelseitig Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch Freiwinkel: 0° Eckenradius: 1.2 mm FAQ Welche Werkstoffe kann die VNMG160412 T6215 bearbeiten? Die VNMG160412 T6215 von Tungaloy ist speziell für die Bearbeitung von rostfreiem Stahl ausgelegt und liefert dabei stabile Spanbildung sowie gute Oberflächengüten. Ist die Platte mit gängigen Außenhaltern kompatibel? Ja, die ISO‑Genorm macht die Platte kompatibel zu Standardhaltern; die exakte Passung richtet sich nach Form, Freiwinkel, Toleranz und Befestigung. Wie wirkt sich die CVD‑Beschichtung auf die Standzeit aus? Die CVD‑Beschichtung erhöht die Verschleißfestigkeit und trägt zu längeren Standzeiten sowie gleichmäßiger Schneidkantenleistung bei der Bearbeitung von rostfreiem Stahl bei. Für welche Schnittbedingungen ist die Sorte T6215 geeignet? Die Sorte T6215 eignet sich besonders für stabile bis leicht unterbrochene Schnitte bei rostfreiem Stahl, bietet aber auch Prozesssicherheit bei anspruchsvollen Produktionsbedingungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T6215 Wendeplatten - Tungaloy
VNMG160412 160412 T6215 Drehen — Wendeplatte von Tungaloy VNMG160412 T6215 ist eine ISO-genormte Wendeplatte für präzises Außen- und Innendrehen, speziell entwickelt für die Bearbeitung von rostfreiem Stahl unter stabilen bis leicht unterbrochenen Bedingungen ISO-genormte Rhombus-Wendeplatte mit zylindrischem Loch CVD-beschichtetes Hartmetall für lange Standzeit Eckenradius 1.2 mm für reproduzierbare Konturen Freiwinkel 0° und Schnittwinkel 35° für vielfältige Einsetzbarkeit Doppelseitiger Spanbrecher, beidseitig verwendbar Hohe Verschleißfestigkeit durch Beschichtung und Werkstoff Die CVD-beschichtete Sorte T6215 kombiniert eine verschleißfeste Schicht mit robustem Hartmetall, sodass sich die Wendeplatte besonders bei durchgehend stabilen Schnittbedingungen bewährt. Diese Kombination ermöglicht verlängerte Einsatzintervalle und reduziert Rüstzeiten, weil weniger häufig gewechselt werden muss. Anwender profitieren von konstanter Schneidkante und gleichbleibender Oberflächengüte beim Drehen von rostfreiem Stahl. Präzise Geometrie sorgt für Wiederholgenauigkeit im Prozess Die rhombische Plattenform mit Eckenradius 1.2 mm und einer Plattendicke von 4,76 mm bietet hohe Stabilität in der Halteraufnahme. Der gegebene Schnittwinkel von 35° und der Freiwinkel von 0° ermöglichen flexible Einsatzbilder bei Außen- und Innendrehen. Durch die ISO-Normierung ist die Kompatibilität zum Halter über Form, Größe, Dicke, Befestigung und Toleranzklasse sichergestellt, was die Auswahl des passenden Halters vereinfacht und die Prozesssicherheit erhöht. Systematische Anwendungsempfehlung für produktive Fertigung Für ein wirtschaftliches Zerspanen empfiehlt sich der Einsatz der ISO-Drehplatte im Verbund mit einem passenden Außenhalter oder einer Bohrstange, einer Unterlage/Klemmsatz und den empfohlenen Ersatzschrauben. Die doppelseitigen Spanbrecher ermöglichen beidseitige Nutzung und tragen zur Stabilität der Spanbildung bei. Die VNMG160412 T6215 eignet sich besonders für Anwender mit stabilen Aufspannverhältnissen, die konstante Standzeiten und reproduzierbare Ergebnisse erwarten. Bei Fragen zur Auswahl des passenden Spanbrechers oder Schnittdaten steht die technische Beratung zur Verfügung. Empfehlung: Für eine zuverlässige Serienfertigung die VNMG160412 T6215 Tungaloy-Wendeplatte direkt über Metav Werkzeuge anfragen — Kontakt: info@metav-werkzeuge.com, +49 2822 7131930 Produktmerkmale Artikelnummer: 6878640 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VNMG160412 SKU Hersteller: TUN6878640 Daten Eckenradius: 1.2 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Winkel: 35° Freiwinkel: 0° Besonderheiten Material: Hartmetall Beschichtung: T6215 Schneidstofftyp: CVD-beschichtetes Hartmetall Form: rhombisch Loch: mit Loch (zylindrisches Loch) Spanbrecher: doppelseitig Anwendung: Drehen Modellserie: ISO-Drehwendeschneidplatten FAQ Für welche Werkstoffe ist die Wendeplatte geeignet? Die VNMG160412 T6215 von Tungaloy ist speziell für das Drehen von rostfreiem Stahl entwickelt worden; die verschleißfeste T6215-Beschichtung sorgt für gute Standzeiten bei stabilen bis leicht unterbrochenen Bedingungen. Ist die Plattenform kompatibel mit Standardhaltern? Ja, die Plattenform rhombisch und die ISO-Genormung ermöglichen Kompatibilität mit gängigen Außenhaltern und Bohrstangen, sofern Form, Größe, Dicke und Befestigung übereinstimmen. Wie wirkt sich der Eckenradius auf die Bearbeitung aus? Der Eckenradius von 1.2 mm sorgt für reproduzierbare Konturen und höhere Kantendurchlauffestigkeit; er eignet sich für Anwendungen, die eine saubere Kantenbildung und stabile Spanbildung benötigen. Kann die Wendeplatte beidseitig verwendet werden? Ja, die Platte verfügt über einen doppelseitigen Spanbrecher und kann entsprechend beidseitig genutzt werden, was die Wirtschaftlichkeit erhöht. Welche Systemkomponenten werden empfohlen? Für den Betrieb sind ein passender ISO-Außenhalter oder eine Bohrstange, eine Unterlage/Klemmsatz und geeignete Ersatzschrauben erforderlich; dies gewährleistet sichere Befestigung und exakte Wiederholgenauigkeit. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T9205 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated cemented carbide wear resistance, a 35° rhombic geometry and a robust 1.2 mm corner radius for consistent, productive turning of steel; order directly via Metav Werkzeuge or contact our technical consultants for application advice. VNMG 160412 T9205 indexable turning insert — 35° rhombic, CVD-coated carbide by Tungaloy The VNMG160412 T9205 is an ISO rhombic indexable insert designed for productive external and internal turning of steel under stable machining conditions. ISO rhombic geometry, 35° cutting edge CVD-coated carbide for high wear resistance 1.2 mm corner radius for enhanced edge strength High productivity through a wear-resistant grade The T9205 grade is a CVD-coated cemented carbide developed for high wear resistance and consistent performance at elevated cutting speeds. In practice, the T9205 cutting material maintains edge integrity across longer cuts, reducing the frequency of insert changes and supporting continuous production cycles. For manufacturers seeking measurable gains in throughput, this grade offers a reliable compromise between tool life and cutting rate, especially when machining non-hardened and alloyed steels under stable setup conditions. Geometry that supports stable setups and predictable results A 35° rhombic shape combines a small approach angle with a compact footprint, providing a good balance between cutting force distribution and access to confined features. The insert’s 1.2 mm corner radius increases edge robustness and reduces the risk of premature chipping during interrupted cuts. The insert thickness of 4.76 mm and 16 mm size mean that clamping and holder selection must match the ISO form, clearance angle and tolerance class to ensure correct seating; compatibility is determined by shape, relief (0° clearance), tolerance class, clamping method, size and thickness. Practical system and application guidance for reliable machining This insert is supplied as part of an ISO-based system: indexable insert, an appropriate external holder or boring bar, shim/clamping set and replacement screws. The dual-sided chipbreaker provides options for consistent chip control when conditions are stable and rigidity is adequate. Typical applications include external turning and internal turning where surface integrity and repeatable tool life are priorities. For mixed-production environments, pairing this insert with rigid fixturing and moderate to high speeds will produce the best balance of productivity and finish quality. For application-specific recommendations or to secure inventory of Tungaloy T9205 inserts for steel turning, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and prompt supply. Technical data Article number: 6785674 Manufacturer SKU: TUN6785674 SKU: 6785674-Tungaloy Model series: ISO turning indexable inserts Grade: T9205 (CVD-coated) Material: cemented carbide Application: Turning Insert designation: VNMG160412 Shape: rhombic, 35° Corner radius: 1.2 mm Thickness: 4.76 mm Insert size: 16 mm Hole: with cylindrical hole Chipbreaker: double-sided Facts Diameter / size: 16 mm Thickness: 4.76 mm Corner radius: 1.2 mm Approach angle: 35° Clearance angle: 0° Article number: 6785674 Manufacturer SKU: TUN6785674 Special features CVD-coated cemented carbide for wear resistance ISO-compatible insert for standard holders Rhombic form for versatile turning Dual-sided chipbreaker for consistent chip control Suitable for stable, high-speed turning of steel Supplied as part of an ISO insert system FAQ What steels is this grade suited for? The T9205 grade on the VNMG160412 insert is optimised for machining a broad range of steels under stable conditions, delivering wear resistance and predictable tool life. How does the 35° geometry affect cutting? A 35° rhombic approach reduces radial cutting forces and improves tool access; the VNMG160412 geometry therefore supports smoother cutting and easier entry into tight features. Is the insert reversible or single-use? The insert has multiple usable edges due to its indexable design; the dual-sided chipbreaker allows turning one edge, then indexing to the next to extend effective tool life. What holder features are required for safe use? Compatibility depends on form, clearance angle (0°), tolerance class, clamping method, size and thickness; use ISO-compatible holders sized for a 16 mm VNMG insert and ensure secure clamping with the appropriate shim and screw set. Are there recommended cutting conditions for first trials? Begin with moderate cutting speeds and feeds appropriate for alloyed steel; because the T9205 grade tolerates higher speeds, parameters can be adjusted upward once stable chip formation and surface finish are confirmed. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide T9215 and a 1.2 mm nose radius for durable, high-productivity medium-steel turning; the ISO compatibility and rhombic geometry ensure straightforward integration into standard toolholders. Order directly via Metav Werkzeuge or consult our specialists for application support. VNMG 160412 T9215 – Turning indexable insert (ISO) by Tungaloy The VNMG160412 T9215 is an ISO-standard indexable insert for external and internal turning, optimised for medium-steel machining and continuous to slightly interrupted cuts. CVD-coated carbide T9215 Optimised for medium steel Rhombic 35° geometry Double-sided chipbreaker, with hole Consistent productivity from the CVD-coated grade The T9215 grade combines a CVD-coated carbide substrate with a formulation tuned for medium-steel applications, delivering high wear resistance and good fracture toughness. This composition supports longer tool life in continuous and lightly interrupted cuts, which in turn increases throughput and reduces tool-change frequency. The coating improves thermal stability and helps maintain a sharp cutting edge under sustained cutting conditions, making the insert a reliable choice when consistent component quality and uptime are priorities. Easy fitting and predictable process behaviour The rhombic VNMG geometry with a 35° approach angle and 0° relief allows stable engagements and predictable chip flow, while the 1.2 mm nose radius strikes a balance between edge strength and surface finish. Compatibility with ISO holders is determined by form, relief angle, tolerance class, clamping method, size and thickness, so the insert integrates cleanly into standard turning systems. Clear nominal dimensions and standardised mounting reduce set-up time and simplify tool inventory planning, improving overall process control. Practical selection guidance for workshop use For external and internal turning select the insert version and chipbreaker according to workpiece material, machining stability and the desired surface result; the double-sided chipbreaker reduces inventory while maintaining reliable chip control. The cylindrical hole ensures secure clamping in common ISO-style clamping systems. When machining medium steel, the CVD-coated grade is the primary recommendation for productivity and repeatability; for heavily interrupted cuts or exotic alloys, consider alternative grades or geometries tailored to those demands. For high-productivity medium-steel turning, specify Tungaloy's T9215 grade and request supply or technical guidance from Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6772352 SKU: 6772352-Tungaloy Manufacturer SKU: TUN6772352 Material: Carbide Model series: ISO turning indexable inserts Facts Nose radius: 1.2 mm Size: 16 mm Relief angle: 0° Insert angle: 35° Special features Grade: T9215 Coating: CVD-coated carbide Shape: Rhombic (VNMG) Chipbreaker: Double-sided Hole: Cylindrical hole Application: External and internal turning; medium steel; continuous to slightly interrupted cuts Compatibility: ISO holders (form, relief angle, tolerance class, clamping, size, thickness) FAQ Which materials is this insert optimised for? The VNMG160412 T9215 insert from Tungaloy is optimised for medium-steel machining, combining CVD-coated carbide and a chipbreaker that supports continuous to slightly interrupted cuts. How does the 1.2 mm nose radius affect results? A 1.2 mm nose radius on the VNMG160412 improves edge strength for stable turning while still allowing a good surface finish when machining medium steel with appropriate feeds. Is this insert compatible with standard ISO holders? Yes, the insert follows ISO dimensions (160412) and is compatible with ISO turning holders; compatibility depends on form, relief angle, tolerance class, clamping and size. What does the double-sided chipbreaker mean for inventory? The double-sided chipbreaker on the VNMG160412 T9215 permits indexing of both edges, reducing the number of inserts required and lowering tooling inventory costs. Does the insert include a hole and what is its purpose? The VNMG160412 is supplied with a cylindrical hole to ensure secure and repeatable clamping in common ISO-style insert seats. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide T9215 and a 35° rhombic geometry for reliable medium-steel turning with consistent tool life; order directly via Metav Werkzeuge or contact our consultants for machining advice. VNMG 160412 T9215 — Turning insert (ISO) by Tungaloy — CVD-coated carbide, 35° rhombic geometry VNMG160412 T9215 is an ISO-standard insert for precision turning, intended for external and internal turning with a focus on medium-steel machining CVD-coated carbide grade T9215 35° rhombic geometry for versatile turning 1.2 mm corner radius for stable cutting Increased productivity for medium-steel operations The T9215 grade is a CVD-coated carbide developed for sustained performance in medium steel machining. Its composition balances wear resistance with fracture toughness, enabling higher cutting speeds and longer tool life in continuous to slightly interrupted cuts. This results in fewer tool changes and more stable cycle times on production parts. The engineered coating supports thermal resistance and reduces adhesive wear, which directly contributes to predictable tool behaviour and cost-effective machining. Stable cutting edge for improved surface finish A 35° rhombic geometry combined with a 1.2 mm corner radius provides a secure cutting edge that resists chipping under typical turning loads. The double-sided chipbreaker promotes controlled chip formation, reducing vibration and improving the consistency of the machined surface. For operators seeking repeatable component quality, this geometry enhances dimensional stability and delivers improved surface quality with fewer rework steps. ISO compatibility and straightforward tool set-up The insert complies with ISO-standard dimensions and is supplied with a cylindrical hole and a plate thickness of 4.76 mm, facilitating secure clamping in compatible holders. The fit to the holder is determined by form, clearance angle (0°), tolerance class, fastening and size; attention to these interfaces ensures repeatable seating and optimal transfer of forces during turning. The item is available under manufacturer SKU TUN6772362 and article number 6772362 for easy procurement and tool management. Practical selection advice for efficient machining For efficient, economical turning choose the chipbreaker and grade that match workpiece material and machine stability — T9215 is recommended as a first choice for medium-steel applications where a balance of productivity and tool life is required. Use the rhombic insert for both external profiling and light internal turning where rigidity is sufficient. If clarification on cutting parameters or holder compatibility is needed, supplementary cutting data can be provided to align feed and speed with production goals. Contact Metav Werkzeuge for tailored application support on Tungaloy inserts and ensure the T9215 grade is configured for optimum process reliability Technical data Article number: 6772362 Manufacturer SKU: TUN6772362 Our SKU: 6772362-Tungaloy Label: VNMG160412 T9215 Tungaloy insert Material: carbide Core dimensions and ratings Corner radius: 1.2 mm Cutting edge angle: 35° Clearance angle: 0° Size: 16 mm Plate thickness: 4.76 mm Design and special features ISO turning insert (rhombic) CVD-coated grade T9215 Double-sided chipbreaker Cylindrical hole for secure fastening Suitable for external and internal turning Optimised for continuous to slightly interrupted cuts Intended for medium-steel machining FAQ What materials is this insert best suited for? The VNMG160412 T9215 insert is optimised for medium-steel machining, where its CVD-coated carbide provides a balance of wear resistance and toughness. Is the insert compatible with standard ISO holders? Yes, the insert follows ISO dimensions; compatibility depends on holder form, clearance angle, tolerance class, fastening, size and thickness to ensure correct seating. How does the double-sided chipbreaker affect performance? The double-sided chipbreaker ensures controlled chip formation and improved stability, which supports consistent surface quality and longer tool life with the T9215 grade. Which SKU should be used when ordering replacement inserts? Order using article number 6772362 or manufacturer SKU TUN6772362 to ensure the correct VNMG160412 T9215 insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance and stable chip control for continuous, productive turning operations; the CVD-coated carbide grade T9215 provides consistent performance in medium-steel machining. Order genuine inserts through Metav Werkzeuge or contact the specialists for compatibility advice. VNMG160412 T9215 VNMG turning insert for Turning — CVD-coated carbide, 35° (Tungaloy) A VNMG160412 T9215 ISO insert designed for external and internal turning, offering robust wear resistance and reliable chip control for medium-steel applications. CVD-coated carbide for high wear resistance Optimised for medium steel machining Double-sided chipbreaker for stable chips ISO rhombic VNMG form with 35° approach angle Productivity advantage for medium-steel turning The CVD-coated carbide grade T9215 combines wear resistance with fracture toughness to sustain higher cutting speeds and longer tool life in continuous or lightly interrupted cuts. This results in measurable gains in productivity: reduced tool changes and more consistent cycle times. The coating enhances thermal protection and adhesion resistance, while the substrate ensures a robust cutting edge—benefits that translate into fewer process interruptions and improved overall equipment effectiveness. System compatibility and secure clamping Compatibility with the toolholder is determined by form, relief angle, tolerance class, attachment method, size and thickness; the ISO designation ensures predictable fit in standard holders. The rhombic VNMG geometry, 35° approach angle and 0° relief angle create a balanced cutting action that suits a wide range of external and internal turning tasks. Inserts are supplied with a cylindrical hole for positive location; proper use of the correct holder, backing clamp and replacement screws secures repeatable positioning and contributes to consistent part quality. Chip control and application guidance The double-sided chipbreaker is optimised for medium-steel conditions and supports stable chip formation, which improves surface finish and reduces the risk of chip-related interruptions. In practice, choose feeds and depths that match the grade’s strength: stable, medium-depth cuts benefit from the insert’s resistance to wear and edge chipping. For lightly interrupted cuts the combination of coating and substrate lowers the likelihood of premature edge breakdown, while reliable chip control simplifies swarf handling and machine housekeeping. Contact Metav Werkzeuge for genuine Tungaloy VNMG160412 inserts and tailored holder recommendations — email info@metav-werkzeuge.com or call +49 2822 7131930 for technical consultation and fast supply Technical data Article number: 6774111 Manufacturer SKU: TUN6774111 Manufacturer: Tungaloy Model series: ISO turning inserts Grade/coating: T9215 (CVD-coated carbide) Facts Insert designation: VNMG160412 Size: 16 mm Corner radius: 1.2 mm Relief angle: 0° Approach angle: 35° Hole style: cylindrical Special features Double-sided chipbreaker Rhombic plate shape (VNMG) ISO-compliant insert Suitable for external and internal turning Compatible with corresponding holder, backing clamp and screws FAQ What materials is this insert suitable for? The Tungaloy VNMG160412 in grade T9215 is intended primarily for medium steel machining and offers a balance of wear resistance and toughness for productive turning. How does the T9215 grade affect cutting performance? Grade T9215 (CVD-coated carbide) provides thermal and abrasion resistance while retaining edge strength, making the insert suitable for continuous and lightly interrupted turning operations. Is the insert compatible with standard ISO holders? The VNMG160412 follows ISO dimensions; compatibility depends on holder form, relief angle, tolerance and clamping method—use the matching VNMG holder, backing clamp and screws for secure location. What chip control can be expected with this geometry? The double-sided chipbreaker on this rhombic insert produces stable chips under recommended cutting conditions, improving surface finish and reducing swarf-related disruption. Does the insert suit internal turning as well as external turning? Yes, the ISO rhombic geometry and tooling system setup make the insert appropriate for both external and internal turning when fitted in a compatible holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance and fracture toughness together with ISO compatibility for straightforward tool changes and consistent productivity; order directly via Metav Werkzeuge or consult the technical team for application advice. VNMG160412 T9215 – VNMG turning insert (ISO 160412) by Tungaloy, CVD-coated cemented carbide A VNMG160412 T9215 indexable turning insert engineered for external and internal turning, optimised for medium steel machining with a robust chip control solution. CVD-coated cemented carbide grade T9215 ISO‑standard VNMG160412 geometry Double-sided chipbreaker for reliable chips 1.2 mm corner radius, 35° lead angle Productivity through a proven ISO geometry The VNMG format follows ISO-standard geometry, ensuring predictable seating and repeatable tool offsets when paired with compatible holders. The rhombic shape and 35° lead angle deliver a balance between cutting edge strength and access in shoulder and profile turning, which supports stable cutting conditions and reduces tool change downtime. Compatibility depends on form, clearance angle, tolerance class, fixing method, size and thickness; this standardised approach simplifies inventory and minimises setup errors on the shop floor. Extended tool life with the T9215 coating system The T9215 grade combines a CVD-coated surface with a tough cemented carbide substrate to deliver both wear resistance and fracture toughness. This makes the insert a first choice for medium steel work, enabling productive cutting at continuous to slightly interrupted cuts. The double-sided chipbreaker improves chip control and reduces heat concentration at the cutting edge; the corner radius 1.2 mm contributes to edge strength and consistent surface finish while permitting moderate feeds without sacrificing component quality. Seamless integration and application guidance Integration into a machining system requires the insert, a suitable outer holder or boring bar, a backplate/clamp set and replacement screws; the cylindrical hole ensures secure clamping. For best results, match the chipbreaker and grade to the material, operation and machine rigidity: select a more robust chipformer and conservative parameters for interrupted cuts, or exploit the grade's productivity in stable continuous turning of steel. For complex requirements or uncertain fit, Metav Werkzeuge's technical advisors can provide tailored recommendations and machining parameter guidance. Contact Metav Werkzeuge for tailored application advice on the Tungaloy VNMG160412 and ensure optimal grade and chipbreaker selection for reliable production results Technical data Article number: 6796100 Manufacturer SKU: TUN6796100 Seller SKU: 6796100-Tungaloy Material: Cemented carbide Coating: T9215 (CVD-coated) Facts Form/ISO: VNMG160412 Thickness: 4.76 mm Size: 16 mm Corner radius: 1.2 mm Lead/approach angle: 35° Clearance angle: 0° Hole: with hole (cylindrical) Special features Double-sided chipbreaker Rhombic plate form ISO-compatible turning insert Suitable for external and internal turning Optimised for medium steel machining FAQ What materials is this insert suited for? The Tungaloy VNMG160412 T9215 insert is optimised for medium steel machining; the T9215 grade balances wear resistance and toughness for productive cutting in continuous to slightly interrupted operations. How does the chipbreaker affect machining? The double-sided chipbreaker on this insert improves chip formation and evacuation, reducing heat build-up and promoting a consistent surface finish during turning operations. What dimensions and geometry should be checked for holder compatibility? Ensure the holder matches the VNMG ISO form, thickness (4.76 mm), size (16 mm), 35° lead angle and the cylindrical hole location to guarantee correct seating and clamping repeatability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide grade T9215 and a rhombic VNMG geometry with 35° lead angle for reliable productivity in medium-steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for application support. VNMG 160412 T9215 Turning insert by Tungaloy — rhombic ISO insert, CVD-coated carbide, 35° lead angle VNMG 160412 T9215 is an ISO-standard indexable insert for external and internal turning, designed for medium-steel machining with a focus on high wear resistance and stable chip control CVD-coated carbide for high wear resistance Optimised for medium steel machining Rhombic VNMG shape, 35° lead angle Double-sided insert with central cylindrical hole High productivity through wear-resistant grade and geometry The combination of a CVD-coated surface and a cemented carbide substrate provides a durable cutting edge that sustains longer tool life under continuous and slightly interrupted cutting conditions. The T9215 grade balances wear resistance with fracture toughness, enabling consistent removal rates on a range of medium steel alloys while reducing unscheduled tool changes. The rhombic VNMG geometry with a 35° lead angle contributes to stable cutting forces and a favourable chip flow, which supports higher spindle speeds and improved cycle times in production environments. Fewer tool changes and secure clamping for efficient workflows A double-sided design effectively doubles the available cutting edges, while the central cylindrical hole simplifies precise alignment and secure clamping in compatible holders. The insert’s corner radius 1.2 mm produces robust edge strength for heavier feeds, improving edge life and part finish at moderate cutting depths. Together, these features reduce inventory complexity and downtime for re-indexing, so batch productivity is increased and process reliability is enhanced. Clear integration into ISO-based tooling systems Compatibility with a tooling system is determined by form, clearance angle, tolerance class, fastening method, size and thickness. The insert integrates into standard ISO turning systems comprising a matching external holder or boring bar, a shim/clamping kit and replacement screws for straightforward shop-floor interchangeability. The ISO designation and standard dimensions make it straightforward to select a suitable clamping solution and define cutting parameters, supporting predictable surface quality and repeatable part tolerances. For high-productivity turning operations select the Tungaloy T9215 grade insert and contact Metav Werkzeuge for tailored advice and rapid supply — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6773903 Manufacturer SKU: TUN6773903 Model series: ISO-indexable turning inserts Shape designation: VNMG160412 Application: Turning (external and internal) Core dimensions Size: 16 mm Thickness: 4.76 mm Corner radius: 1.2 mm Lead angle: 35° Clearance angle: 0° Special features Material: cemented carbide Coating/grade: T9215 (CVD-coated) Chipbreaker: double-sided Hole: cylindrical hole for central fastening Platen form: rhombic (VNMG) ISO-standard compatibility FAQ Which materials is this insert best suited for? The Tungaloy VNMG160412 T9215 insert is primarily designed for medium steel machining; the T9215 CVD-coated grade combines wear resistance and toughness for productive steel turning. Is the insert suitable for interrupted cuts? The T9215 grade is intended for continuous to slightly interrupted cutting; its fracture-resistant substrate supports occasional interruptions without significant loss of edge stability. How is holder compatibility determined? Compatibility depends on the insert’s form, clearance angle, tolerance class, fastening style, size and thickness; the VNMG160412 designation and ISO standard help match the correct external holder or boring bar. What are the key dimensions and identifiers for ordering? Key specs: 16 mm size, 4.76 mm thickness, 1.2 mm corner radius, 35° lead angle. Manufacturer article number 6773903 and SKU TUN6773903 identify the exact item. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9215 Wendeplatten - Tungaloy
VNMG160412 T9215 Wendeplatte für Drehen von Tungaloy Die VNMG160412 T9215 ist eine ISO-genormte Wendeplatte für präzises Außen- und Innendrehen in der mittleren Stahlbearbeitung. ISO-genormt VNMG160412 für hohe Kompatibilität CVD-beschichtetes Hartmetall für verbesserte Standzeit Eckenradius 1,2 mm für stabile Spanbildung Rhombische Form mit zylindrischem Loch für einfache Befestigung Doppelseitiger Spanbrecher für konstante Produktivität Produktivität steigern durch robuste Schneidkante Die Kombination aus CVD-Beschichtung und hochwertigem Hartmetall macht diese Wendeplatte zur ersten Wahl für produktive Fertigungsprozesse. Die Sorte T9215 verbindet hohen Verschleißwiderstand mit Bruchsicherheit, was insbesondere bei kontinuierlichem bis leicht unterbrochenem Schnitt Vorteile bringt. Anwender profitieren von längeren Standzeiten und reduziertem Werkzeugwechsel, was die Auslastung von Maschinen erhöht und Rüstzeiten verringert. Materialeigenschaften erklären und Nutzen Die CVD-beschichtung (Chemical Vapour Deposition) bildet eine harte, gleichmäßige Schutzschicht, die Abrieb reduziert und die Schneidkante stabilisiert. Das Basismaterial Hartmetall sorgt für die notwendige Zähigkeit bei wechselnden Schnittbedingungen. Ein Eckenradius von 1,2 mm verbessert die Spanbildung und reduziert Kerbwirkung an der Schneide, was zu gleichmäßigerer Oberflächenqualität und vorhersehbarer Verschleißentwicklung führt. Einsatzbereiche und Maschinenkompatibilität optimieren Die Wendeplatte gehört zur ISO-Drehwendeschneidplatten-Modellserie und eignet sich für Außen- und Innendrehen an Drehautomaten und CNC-Drehzentren. Die Kompatibilität zum Halter richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. In einem typischen Systemaufbau werden Außenhalter oder Bohrstange, Unterlage/Klemmsatz und Ersatzschrauben verwendet, um eine sichere Klemmung und optimale Kraftübertragung zu gewährleisten. Zielgruppe, Auswahl und Anwendungshinweise Diese Wendeplatte ist konzipiert für Fertigungsbetriebe und Lohnbetriebe, die konstante Produktivität und zuverlässige Wiederholungsgenauigkeit benötigen. Für beste Ergebnisse sollte der passenden Spanbrecher und die Sorte entsprechend Werkstoff, Bearbeitungsart und Stabilität gewählt werden. Bei leichter Unterbrechung des Schnitts empfiehlt sich die Sorte T9215, da sie Bruchsicherheit und Verschleißwiderstand kombiniert. Für produktive Stahlzerspanung empfehlen wir die Tungaloy Wendeplatte T9215; technische Beratung und Bestellung über Metav Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 Produktmerkmale Artikelnummer: 6773882 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten SKU: TUN6773882 Daten Eckenradius: 1,2 mm Winkel: 35° Plattengröße: 16 Freiwinkel: 0° Loch: mit Loch (zylindrisches Loch) Besonderheiten Material: Hartmetall Sorte: T9215 (CVD-beschichtet) Plattenform: rhombisch Spanbrecher: doppelseitig Einsatz: Drehen Typ: VNMG160412 Systemaufbau: ISO-Drehplatte, passender Außenhalter oder Bohrstange, Unterlage/Klemmsatz, Ersatzschrauben FAQ Welche Werkstoffe lassen sich mit der VNMG160412 T9215 am besten bearbeiten? Die VNMG160412 T9215 von Tungaloy ist erste Wahl für die mittlere Stahlbearbeitung; die Sorte T9215 bietet hohe Verschleißfestigkeit und gute Bruchsicherheit bei Stahl. Für welche Drehanwendungen ist die Platte geeignet? Die Wendeplatte eignet sich für Außen- und Innendrehen, sowohl bei kontinuierlichem als auch bei leicht unterbrochenem Schnitt; passende Halter und Spanbrecher sind für optimale Ergebnisse wichtig. Was bedeutet die Kennzeichnung VNMG160412 praktisch für die Auswahl? Die Bezeichnung VNMG160412 gibt Form, Größe und Normierung an; sie erleichtert die Auswahl kompatibler Außenhalter und sorgt für Austauschbarkeit im ISO-System. Wie beeinflusst der Eckenradius 1,2 mm die Bearbeitungsergebnisse? Der Eckenradius 1,2 mm fördert stabile Spanbildung und reduziert Spitzenbelastung; das Ergebnis ist eine verbesserte Oberflächengüte und gleichmäßigere Werkzeugstandzeiten. Welche Rolle spielt die CVD-Beschichtung bei der Standzeit? Die CVD-Beschichtung der Sorte T9215 schützt die Schneidkante vor Abrieb und thermischen Einflüssen, was zu längerer Standzeit und konsistenter Leistung führt. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T9215 Wendeplatten - Tungaloy
VNMG160412 160412 T9215 ISO-Drehwendeschneidplatte für Drehen von Tungaloy Die VNMG160412 T9215 ist eine ISO-genormte Drehwendeschneidplatte für präzises Außen- und Innendrehen mit hoher Produktivität und ausgeprägter Verschleißfestigkeit VNMG160412 T9215 von Tungaloy CVD-beschichtetes Hartmetall für mittlere Stahlbearbeitung Rhombische Form mit 35° Schneidwinkel Doppelseitiger Spanbrecher für längere Wirtschaftlichkeit Zylindrisches Loch, Plattendicke 4,76 mm Hohe Prozesssicherheit und Produktivität dank moderner Schneidstoffauswahl Die T9215-Sorte kombiniert CVD-beschichtetes Hartmetall mit einer ausgewogenen Balance aus Verschleißwiderstand und Bruchsicherheit, wodurch sich eine stabile Spanbildung und hohe Schnittparameter realisieren lassen. Anwender profitieren von längeren Standzeiten und konstanter Bearbeitungsqualität selbst bei kontinuierlichem oder leicht unterbrochenem Schnitt. Diese Eigenschaft macht die Platte besonders geeignet für Serien- und Auftragsfertigung, in der Produktivität und reproduzierbare Ergebnisse zählen. Präzision durch Geometrie: Winkel, Radius und Form im Fokus Die rhombische Plattenform mit einem Schneidwinkel von 35° und einem Eckenradius von 1,2 mm ermöglicht exakte Schnittführung bei Außen- und Innendrehprozessen. Der Freiwinkel von 0° und die ISO-Norm erfüllen die Voraussetzung für die sichere Auswahl kompatibler Halter; die Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Dadurch lässt sich die Platte in bestehende Werkzeugaufnahmen integrieren und gewährleistet präzise Maßhaltigkeit und Oberflächengüte. Materialeignung und wirtschaftlicher Einsatz in der Stahlbearbeitung Für die mittlere Stahlbearbeitung ist die Kombination aus Sorte T9215 und CVD-Beschichtung eine wirtschaftliche Wahl, weil sie hohen Verschleißwiderstand mit guter Bruchsicherheit verbindet. Die Platte ist doppelseitig ausgelegt, wodurch sich die Nutzungsdauer pro Einlage verdoppelt und die Teilekosten signifikant sinken. Nutzer sollten Spanbrecher und Sorte entsprechend Werkstoff, Bearbeitungsart und Stabilität wählen, um das optimale Kosten-Nutzen-Verhältnis zu erzielen. Zielgruppe und Praxistipp für Anwender in Fertigung und Handwerk Fertigungsbetriebe, Lohnfertiger und Instandhaltungswerkstätten mit Schwerpunkt auf Stahlbearbeitung profitieren von der robusten Auslegung der Platte und der einfachen Handhabung bei Werkzeugeinrichtung. Bei Unsicherheit über Halterkompatibilität oder Einsatzparameter empfiehlt sich die Rücksprache mit der technischen Beratung, um Schnittdaten und Spanformer optimal abzustimmen. Kleinserien und Serienfertigung profitieren gleichermaßen von der Kombination aus Zuverlässigkeit und Produktivität. Empfehlung: Für produktive Drehprozesse die Tungaloy T9215-Sorte gezielt einsetzen und die VNMG160412 über Metav Werkzeuge anfragen – technische Beratung und Bestellhilfe per eMail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 6772365 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VNMG160412 Hersteller SKU: TUN6772365 Daten Eckenradius: 1,2 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Schneidwinkel: 35° Freiwinkel: 0° Besonderheiten Material: Hartmetall Schneidstofftyp: CVD-beschichtetes Hartmetall Sorte: T9215 Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch Spanbrecher: doppelseitig Einsatz: Außen- und Innendrehen Kompatibilität: abhängig von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke FAQ Was zeichnet die T9215-Sorte aus und für welche Werkstoffe ist sie geeignet? Die T9215-Sorte von Tungaloy bietet eine CVD-Beschichtung mit guter Verschleißfestigkeit und Bruchsicherheit und ist besonders geeignet für die mittlere Stahlbearbeitung; die VNMG160412 T9215 Wendeplatte liefert dabei konstante Ergebnisse bei kontinuierlichem bis leicht unterbrochenem Schnitt. Wie wird die Kompatibilität der VNMG160412 mit dem Drehhalter geprüft? Kompatibilität ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke; bei der VNMG160412 sind diese Parameter ISO-konform, sodass die Zuordnung zu passenden Außenhaltern oder Bohrstangen in der Regel möglich ist. Welche Vorteile bietet der doppelseitige Spanbrecher bei der VNMG160412? Der doppelseitige Spanbrecher erhöht die Wirtschaftlichkeit, weil die Platte beidseitig nutzbar ist, und sorgt für stabile Spanbildung sowie konstante Oberflächenqualität während der Bearbeitung. Wie beeinflusst der Eckenradius von 1,2 mm die Bearbeitungsergebnisse? Ein Eckenradius von 1,2 mm ermöglicht eine robuste Schnittkante, gute Kantenausbildung und eine ausgewogene Mischung aus Zerspanvolumen und Oberflächenqualität; er eignet sich für allgemeine bis anspruchsvolle Stahlbearbeitung. Welche Angaben sind in der technischen Dokumentation zur VNMG160412 zu finden? In der technischen Dokumentation finden sich Artikelnummer 6772365, Hersteller SKU TUN6772365, Plattendicke 4,76 mm, Plattengröße 16 mm, Eckenradius 1,2 mm, Schneidwinkel 35° sowie Hinweise zu Material und Beschichtung (CVD-beschichtetes Hartmetall, Sorte T9215). Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VNMG 160412 T9215 Wendeplatten - Tungaloy
Take advantage of the CVD-coated T9215 grade and the robust VNMG geometry for reliable, high-productivity turning of medium steels; order directly via Metav Werkzeuge or request tailored holder recommendations from our consultants. VNMG160412 T9215 VNMG Turning Insert for Turning (Tungaloy) VNMG160412 T9215 is an ISO-standard indexable turning insert designed for external and internal turning in medium steel, combining CVD-coated carbide performance with a stable geometry. CVD-coated carbide grade T9215 for medium steel Rhombic VNMG form with 35° approach angle 1.2 mm corner radius for edge strength Double-sided chipbreaker; cylindrical hole for secure fixing High wear resistance that boosts productivity The VNMG160412 T9215 insert uses a CVD-coated carbide substrate engineered as a reliable choice for mid-range steel machining. The T9215 grade delivers high wear resistance together with good fracture toughness, which enables longer tool life under continuous and slightly interrupted cuts. This combination reduces tool changes and downtime, resulting in a measurable increase in process efficiency and component throughput for repetitive turning tasks. Stable clamping and ISO compatibility for repeatable finishes Designed as part of the ISO-standard insert family, the rhombic VNMG geometry and specified dimensions ensure compatibility with matching holders and boring bars when the form, free angle, tolerance class, fixing method, size and thickness are aligned. The insert’s cylindrical hole and standard thickness support secure clamping, which reduces vibration and promotes consistent surface quality. Specifying the correct holder and clamping kit therefore directly improves repeatability and reduces scrap rates. Controlled chip formation for external and internal turning The double-sided chipbreaker delivers predictable chip control across a range of feeds and depths of cut, while the 1.2 mm corner radius balances edge strength with dimensional accuracy. The insert’s 4.76 mm thickness and 16 mm inscribed size provide a robust platform for turning operations that demand stability. As part of a complete system—ISO insert, appropriate external holder or boring bar, shim/clamp set and spare fixing screws—the geometry and chip control support higher material removal rates with reduced risk of edge chipping. For productive medium-steel turning with Tungaloy quality, contact Metav Werkzeuge for holder matching and availability — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application-specific recommendations. Technical data Article number: 6966283 Manufacturer SKU: TUN6966283 Label: VNMG160412 T9215 Tungaloy-Wendeplatte Model series: ISO-Drehwendeschneidplatten Application: Turning Facts Corner radius: 1.2 mm Approach/lead angle: 35° Free angle: 0° Plate thickness: 4.76 mm Inscribed circle / size: 16 Special features Rhombic VNMG insert shape CVD-coated carbide (T9215) Double-sided chipbreaker Cylindrical hole for fixing Suitable for continuous to light interrupted cuts System components: ISO insert, matching holder or boring bar, shim/clamp set and spare screws FAQ Which materials is this insert intended for? The VNMG160412 T9215 insert is optimised for medium steel machining; the T9215 CVD-coated carbide balances wear resistance and toughness for continuous to light interrupted turning. How is the insert secured in the holder? The insert features a cylindrical hole and standard ISO dimensions; securing requires a compatible holder and clamping kit matched to the VNMG form, thickness and tolerance class. What cutting geometry and edge radius does it offer? The rhombic VNMG geometry provides a 35° approach angle and a 1.2 mm corner radius, offering a compromise between edge strength and finish for turning operations. Can this insert be used for both external and internal turning? Yes, the insert is suitable for external and internal turning when combined with the appropriate external holder or boring bar and the correct clamping components. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9225 Wendeplatten - Tungaloy
Robust CVD-coated carbide T9225 with a 35° rhombic geometry and a 1.2 mm corner radius ensures stable machining in medium to heavy steel turning; compatible with ISO holders and supplied with a cylindrical hole for secure clamping. Order the insert directly via Metav Werkzeuge or consult our advisers for holder matching and process optimisation. VNMG160412 T9225 turning insert — Tungaloy CVD-coated carbide, 35° rhombic A VNMG160412 T9225 rhombic indexable insert for turning, designed as a robust universal grade for medium to heavy steel machining and suited to interrupted cuts. CVD-coated carbide T9225 Suitable for medium to heavy steel Rhombic 35° geometry, VNMG form Double-sided chipbreaker, cylindrical hole Stable performance under variable cutting conditions The T9225 grade is a CVD-coated carbide designed for reliability in changing engagement and slightly interrupted cuts. Its formulation delivers a balance of toughness and wear resistance, reducing the risk of premature edge failure when operations vary between stable and intermittent contact. For production environments where consistency matters, this insert maintains cutting-edge integrity while preserving dimensional accuracy and surface quality. Enhanced edge strength and surface finish for interrupted turning With a 1.2 mm corner radius and a double-sided chipbreaker, the insert improves edge strength and chip control during heavier passes. The corner radius increases resistance to mechanical shock, which is particularly beneficial for interrupted cuts and modest overhangs. As a result, cycle times can be optimised through more reliable cutting parameters and fewer unplanned tool changes, contributing to a smoother workflow and predictable machining results. Secure clamping and ISO compatibility explained Designed to the ISO series of indexable turning plates, the geometry and the cylindrical hole guarantee consistent fitment to matching holders. Compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness; these parameters ensure a secure connection between insert and holder, minimising micro-movements that can degrade finish. Choosing the correct holder and torque for the screw secures repeatable seating and extends insert life. Material versatility and production economy The hardmetal substrate and CVD coating offer a cost-effective solution across a broad range of steels, making the insert suitable for many workshop and production tasks. The universal character of the grade reduces the need for multiple specialised grades, simplifying tool inventory and accelerating setup. When combined with correct cutting data, the result is improved productivity and lower total tooling cost per part, while preserving machining quality. Contact Metav Werkzeuge today for advice on integrating Tungaloy T9225 inserts into production, or request holder compatibility support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6780896 Manufacturer SKU: TUN6780896 SKU: 6780896-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Numbers / Core technical data Size: 16 mm Plate thickness: 4.76 mm Corner radius: 1.2 mm Geometry angle: 35° Clearance angle: 0° Special features / Versions Grade: T9225 (CVD-coated) Form: rhombic (VNMG) Hole: with hole — cylindrical hole Chipbreaker: double-sided Typical use: external and internal turning FAQ What applications is this insert intended for? The Tungaloy VNMG160412 T9225 insert is intended for external and internal turning, especially in medium to heavy steel machining and situations with slightly interrupted cuts. How does the T9225 grade differ from other grades? T9225 is a robust universal CVD-coated carbide grade that emphasises toughness for variable engagement and interrupted cutting, offering a compromise between wear resistance and edge strength. Which corner radius is available and why does it matter? This insert has a 1.2 mm corner radius, which increases edge strength and improves resistance to mechanical shock, benefiting interrupted operations and enhancing surface finish. Is the insert compatible with standard ISO holders? Yes, the VNMG160412 follows ISO dimensions; compatibility with a holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness to ensure secure seating. Can this insert handle prolonged heavy cuts? As a universal robust grade, the insert performs well in medium to heavy cutting; however, cutting data and machine stability should be adjusted to application specifics to maximise tool life and process safety. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of high toughness, reliable chip control and easy integration into ISO tool systems for uninterrupted production. The CVD-coated T9225 grade provides robust performance in medium-to-heavy steel turning while the rhombic geometry and double-sided chipbreaker aid consistent surface quality. Order the insert directly via Metav Werkzeuge or ask our consultants for application support. VNMG160412 T9225 VNMG turning insert — CVD-coated carbide, 35° lead angle — Tungaloy VNMG160412 T9225 is an ISO rhombic turning insert developed for external and internal turning applications, optimised for medium-to-heavy steel machining. ISO VNMG160412 rhombic insert, 16 mm size CVD-coated carbide grade T9225 for steel machining 0° clearance, 35° lead angle for stable cutting Double-sided chipbreaker with cylindrical hole fixation Durable grade for demanding steel operations The CVD-coated carbide of the T9225 grade is formulated for demanding turning tasks where varying engagement and light interruptions occur. This composition balances toughness and wear resistance to reduce edge chipping during interrupted cuts and to extend tool life under fluctuating loads. The result is improved process stability and fewer insert changes, contributing to predictable cycle times and lower tooling-related downtime. Geometry that controls chips and surface finish The VNMG rhombic form with a 1.2 mm corner radius and double-sided chipbreaker provides controlled chip formation and repeatable surface integrity. The centred, cylindrical hole enables secure fastening in the clamping system, while the 35° lead angle and 0° clearance support stable contact conditions at the tool–workpiece interface. For operators, this means easier parameter setup and a higher probability of consistent part-to-part finish when the correct cutting data are applied. ISO compatibility for straightforward mounting and replacement As an ISO-standard indexable insert, compatibility with holders depends on form, clearance angle, tolerance class, fastening method, size and thickness. The recommended system comprises the indexable plate, a suitable external holder or boring bar, a matching shim/clamping set and replacement screws. This modular approach simplifies inventory management: the insert can be replaced quickly without changing the entire tooling assembly, saving setup time and supporting lean production workflows. Production benefits: efficiency, reliability and predictability Selecting this indexable insert supports a rational approach to machining: the robust grade and engineered geometry combine to lower scrap rates and reduce unscheduled interventions. Stable chip control improves tool life and surface quality, while the insert’s universal characteristics make it suitable for shops that run mixed batches or shift between different steel grades. The result is measurable gains in throughput and part consistency, backed by Tungaloy’s focus on dependable cutting performance. For dependable medium-to-heavy steel turning, request availability of the Tungaloy VNMG160412 T9225 insert from Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com / +49 2822 7131930 for tailored cutting data and rapid delivery Technical Data Article number: 6780768 Manufacturer SKU: TUN6780768 Material: Carbide Coating: CVD Grade: T9225 Model series: ISO turning indexable inserts Facts Size: 16 mm Thickness: 4.76 mm Corner radius: 1.2 mm Lead angle: 35° Clearance angle: 0° Hole: with hole (cylindrical) Plate form: rhombic Special features Double-sided chipbreaker Suitable for external and internal turning Robust universal grade for medium-to-heavy steel ISO-compatible mounting system FAQ What materials is this insert suitable for? This insert with T9225 CVD-coated carbide is designed primarily for medium-to-heavy steel machining and performs well under changing engagement conditions. How does the chipbreaker design affect machining results? The double-sided chipbreaker on the VNMG geometry promotes controlled chip formation and aids surface finish consistency while reducing the risk of entanglement. Which holders are compatible with this ISO insert? Compatibility depends on form, clearance angle, tolerance class, fastening, size and thickness; use a matching external holder or boring bar with the correct shim and screws for secure clamping. What is the corner radius and how does it influence the cut? The 1.2 mm corner radius provides a balance between strength and surface finish, offering improved edge robustness for heavier cuts while maintaining acceptable workpiece quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VNMG 160412 T9225 Wendeplatten - Tungaloy
VNMG 160412 T9225 Wendeplatte zum Drehen von Tungaloy Die VNMG 160412 T9225 Wendeplatte ist eine ISO-genormte, rhombische Schneidplatte für das Außen- und Innendrehen und bietet robuste Performance bei wechselnden Eingriffsbedingungen ISO-genormte rhombische Wendeplatte 16 mm CVD-beschichtetes Hartmetall T9225 Eckenradius 1,2 mm für universellen Einsatz Doppelseitiger Spanbrecher für stabile Spanform Zylindrisches Loch, kompatibel mit gängigen Haltersystemen Materialstärke und Standzeit für produktive Zerspanung Die Kombination aus Hartmetall Grundstoff und der T9225 CVD-Beschichtung sorgt für eine hohe Verschleißfestigkeit und gute Zähigkeit bei unterbrochenen Schnitten. Durch die robuste Sortenwahl lässt sich die Standzeit merklich erhöhen, wodurch Rüstintervalle länger und Stillstandszeiten kürzer werden. Die Wendeplatte eignet sich für mittlere bis schwere Stahlbearbeitung, wenn Prozesssicherheit und konstante Ergebnisse gefragt sind. Präzision beim Drehen durch genormte Geometrie Die ISO-Drehwendeschneidplatten Geometrie gewährleistet reproduzierbare Schnittbedingungen: der Freiwinkel von 0° und der Eckenradius von 1,2 mm liefern stabile Werkstückoberflächen bei Außen- und Innendrehoperationen. Die rhombische Form und die Plattendicke von 4,76 mm verbessern die Auflagefläche im Halter und reduzieren Vibrationen, sodass Oberflächengüte und Maßhaltigkeit optimiert werden. Für Anwender in Industrie und Werkstatt konzipiert Entwickelt für Anwender, die produktive Zerspanung mit hoher Wirtschaftlichkeit verbinden wollen, passt die Wendeplatte in Serienfertigung wie auch in Einzelteilfertigung. Maschinenbediener, Fertigungsplaner und Lohnfertiger profitieren von der universellen Einsetzbarkeit der VNMG 160412 T9225 sowie von der einfachen Austauschbarkeit dank ISO-Normierung und zylindrischem Loch. Technische Robustheit und flexible Einsatzfelder Das doppelseitige Spanbrechersystem unterstützt eine kontrollierte Spanbildung auch bei wechselnder Schnittführung. Die CVD-Beschichtung reduziert Adhäsion und erhöht die Schnittstabilität, wodurch Prozesse bei variierenden Eingriffsbedingungen verlässlicher laufen. Für Anwender bedeutet das geringeren Werkzeugwechselaufwand und gleichbleibende Teilequalität. Empfehlung: Entscheiden Sie sich für die Tungaloy Wendeplatte mit T9225 Beschichtung für stabile Zerspanungsergebnisse; bei Fragen zur Werkzeugauswahl kontaktieren Sie uns per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6966284 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Artikelname: VNMG160412 T9225 Tungaloy-Wendeplatte SKU: TUN6966284 Fakten Radius: 1,2 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Winkel: 35° Freiwinkel: 0° Besonderheiten Material: Hartmetall Beschichtung: T9225 (CVD, Chemische Gasphasenabscheidung) Plattenform: rhombisch Loch: mit Loch, zylindrisches Loch Spanbrecher: doppelseitig Schneidstofftyp: CVD-beschichtetes Hartmetall Einsatzbereich: Außen- und Innendrehen FAQ Welche Einsatzbereiche deckt die VNMG 160412 T9225 ab? Die VNMG 160412 T9225 Wendeplatte von Tungaloy eignet sich primär für das Außen- und Innendrehen von Stahlbauteilen und ist für mittlere bis schwere Bearbeitungen konzipiert. Welche Vorteile bietet die T9225 Beschichtung? Die T9225 Beschichtung (CVD) erhöht die Verschleißfestigkeit und verbessert die Spansteuerung, wodurch die Standzeit der Tungaloy Wendeplatte verlängert wird. Ist die Wendeplatte mit gängigen Haltern kompatibel? Ja, die ISO-Norm und das zylindrische Loch ermöglichen die Kompatibilität mit vielen gängigen Außenhaltern und Bohrstangen; für spezielle Halter bitte Halterform und Toleranzklasse prüfen. Welche Geometrie sorgt für die Stabilität beim Schnitt? Die rhombische Form kombiniert mit einem Eckenradius von 1,2 mm und einem Freiwinkel von 0° sorgt für stabile Schnittbedingungen und gute Oberflächengüten. Wie erkenne ich die richtige Sorte für meine Anwendung? Die Sorte T9225 ist eine robuste Universalsorte für wechselnde Eingriffsbedingungen; bei sehr abrasiven oder extrem harten Werkstoffen empfiehlt sich eine sortenspezifische Abstimmung mit der Fertigungsplanung. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com