CNGG 120402 NS520 Wendeplatten - Tungaloy
Benefit from ISO conformity and the NS520 cermet grade for consistent surface finish and predictable wear; the rhombic insert with a 0.2 mm corner radius and cylindrical hole delivers secure clamping and compatibility with standard holders. Order the insert directly via Metav Werkzeuge or consult the technical team for application advice and holder matching. CNGG120402 NS520 CNGG indexable insert for turning — Tungaloy The CNGG120402 NS520 is an ISO‑standard rhombic indexable insert designed for external and internal turning, optimised for finishing and light machining of steel. ISO‑standard CNGG form, consistent fit NS520 cermet for fine surface finish 0.2 mm corner radius for accurate profiles Cylindrical hole, secure clamping Predictable performance for productive turning The ISO‑standard geometry ensures repeatable seating and interchangeability across compatible holders, enabling stable cycle times and predictable tool changes. With the NS520 composition — a cermet or coated cermet grade — the insert is tailored for finishing and light machining of steel where surface integrity and dimensional accuracy matter. The indexable insert concept reduces downtime through quick insert changes and helps to maintain a continuous production flow while preserving component tolerances. Achieve consistent surface quality with controlled wear For operations where surface finish and uniform wear are priorities, the combination of a cermet grade and the insert geometry yields tangible benefits. Cermet materials balance wear resistance and polishability, so components emerge with improved surface texture and minimal edge breakdown over longer runtimes. The result is fewer reworks and a more consistent first‑pass quality, particularly on turned parts requiring tight dimensional control and refined surface appearance. Secure seating and accurate profile generation The rhombic plate form paired with an 80° approach angle and 0° clearance creates a stable cutting position for profile accuracy. The 0.2 mm corner radius supports fine detail and prevents premature corner chipping when machining contours, while the cylindrical hole ensures reliable clamping and correct axial location in holders designed for ISO‑CNGG plates. The plate thickness of 4.76 mm and 12 mm size harmonise with common clamping systems; compatibility must be checked against holder form, tolerance class and fastening method before installation. Flexible chip control and selection guidance Equipped with a double‑sided chipbreaker, the insert allows reversal and continued use of both cutting edges to extend service life and optimise cost per edge. Selecting the right chipbreaker, grade and holder stability is critical: the NS520 grade favours finish passes and light cuts, whereas alternative grades would be chosen for roughing or higher feed rates. For complex parts or mixed‑material batches, Metav Werkzeuge’s technical advisers can provide tailored recommendations to match process stability with the required surface and dimensional outcomes. Contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to review the suitability of the Tungaloy CNGG120402 NS520 insert for specific applications and to request ordering and compatibility support Technical details Article number: 6801853 Manufacturer item number: 6801853 Manufacturer SKU: TUN6801853 SKU: 6801853-Tungaloy Model series: ISO-Drehwendeschneidplatten Core data Shape: rhombic Size: 12 mm Thickness: 4.76 mm Corner radius: 0.2 mm Approach angle: 80° Clearance angle: 0° Hole: cylindrical Materials & features Material: cemented carbide Grade/coating: NS520 (cermet / coated cermet) Chipbreaker: double‑sided Application: turning System: ISO indexable insert, compatible with appropriate holders FAQ What materials is this insert designed to machine? The NS520 grade is optimised for machining steel in finishing and light cutting operations; the CNGG form is suited to common steel turning tasks requiring good surface finish. How to verify holder compatibility with the insert? Compatibility depends on insert form, clearance angle, tolerance class, clamping style, size and thickness; confirm the holder is specified for ISO CNGG geometry before fitting the insert. What advantages does the NS520 cermet offer? NS520 provides enhanced surface finish and even wear behaviour compared with some carbide grades, making it suitable for finishing passes where component appearance and dimensional stability are important. Can the insert be used on both sides? Yes, the double‑sided chipbreaker permits turning over to the second cutting edge, extending usable life per insert and improving cost efficiency. Is the insert supplied ready to mount? The plate is delivered as an ISO indexable insert with a cylindrical hole for clamping; ensure the correct screws and clamp or seat are used as specified by the holder manufacturer. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120402 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of an ISO CNGG120402 geometry, the NS9530 uncoated cermet grade and a 0.2 mm corner radius for low cutting forces and an excellent surface finish; order the indexable insert directly via Metav Werkzeuge or ask the consultants for holder compatibility. CNGG 120402 NS9530 Tungaloy indexable insert for turning — ISO CNGG120402, rhombic 80° CNGG120402 NS9530 is an ISO‑standard rhombic insert designed for precision turning and finishing operations in steel. ISO CNGG geometry for consistent clamping NS9530 uncoated cermet for fine finishing 0.2 mm corner radius for superior surface finish Predictable fine finishing with lower cutting forces The NS9530 grade is an uncoated cermet developed for finishing of steel, offering a sharp cutting edge and reduced cutting forces. That combination leads to consistent component surfaces with fewer passes, which benefits cycle time and downstream processes. The cermet microstructure favours continuous cuts and small depths of cut, making this insert ideal where surface integrity and dimensional consistency are required. Secure fit and straightforward system integration Compatibility is governed by the insert’s rhombic form, ISO designation, relief geometry and dimensions rather than the holder alone. The insert’s 0° relief and 80° included angle ensure predictable engagement in matching external holders or boring bars. System components include the ISO insert, a suitable external holder or boring bar, a shim or clamp set and replacement screws, allowing rapid changeover and minimal setup time. Stable chip control and handling suited to finishing A double-sided chipbreaker on the insert reduces chip entanglement during uninterrupted cuts, improving process reliability. The cylindrical hole supports secure clamping, while the 4.76 mm thickness and 12 mm size contribute to mechanical stiffness in the cutting zone. Manufactured from cemented carbide with the NS9530 finishing composition, the insert balances edge sharpness and wear resistance for repeatable results in series production. Contact Metav Werkzeuge for application advice on ISO turning inserts and compatibility checks — Metav Werkzeuge can specify the correct holder and recommend suitable cutting parameters for your turning process. Technical Data Article number: 6997784 Manufacturer SKU: TUN6997784 Model series: ISO-Drehwendeschneidplatten Label: CNGG120402 NS9530 Tungaloy-Wendeplatte Facts Insert size: 12 mm Thickness: 4.76 mm Corner radius: 0.2 mm Included angle: 80° Relief angle: 0° Manufacturer article number: 6997784 Special features Material: cemented carbide Grade: NS9530 (uncoated cermet) Chipbreaker: double-sided Hole: with cylindrical hole Shape: rhombic ISO designation: CNGG120402 Application: turning FAQ What materials is this insert suitable for? The CNGG120402 NS9530 insert is formulated as a finishing grade for steel, providing a sharp edge and low cutting forces suitable for continuous cuts and fine surface requirements. How does the NS9530 grade affect tool life and finish? The NS9530 uncoated cermet emphasises surface finish and low cutting forces; in continuous finishing it produces excellent surfaces while offering competitive wear resistance relative to its class. Which holders are compatible with ISO CNGG120402 inserts? Compatibility depends on holder geometry, clamping style, form and tolerance class; standard external holders and boring bars designed for CNGG inserts and the matching ISO dimensions will accept the CNGG120402 insert. Is this insert indexed or single‑use? The insert is double‑sided, allowing indexing to a fresh edge when one side is worn, which extends usable life and reduces tooling costs per component. What key dimensions should be checked before ordering? Verify the 12 mm size, 4.76 mm thickness, 0.2 mm corner radius and the 80° included angle against the intended holder and workpiece setup for correct fit and performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120402 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of ISO-standard compatibility, a sharp uncoated carbide grade for clean surfaces, and a double-sided chipbreaker for economical use; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CNGG 120402 TH10 Turning insert (ISO 120402) — Tungaloy The CNGG120402 TH10 insert is an ISO-standard rhomboid indexable insert for turning, designed for economical, low-force machining of non-ferrous materials and other applications requiring a clean surface finish. ISO-standard compatibility Sharp uncoated carbide grade TH10 Double-sided chipbreaker for economy Cylindrical hole for secure clamping Reliable fit and straightforward integration for workshop use The ISO-standard design of this rhomboid insert ensures predictable compatibility with matching holders when form, relief angle, tolerance class, clamping method, size and thickness are observed. The cylindrical hole and standardised geometry simplify fixture selection and replacement, reducing set-up time and streamlining inventory management. For production environments where repeatability matters, the standardised format supports consistent seating and repeatable orientation in both external and internal turning operations. Low cutting forces and improved surface quality with TH10 The uncoated TH10 grade is a sharp, universal carbide developed for non-ferrous materials and processes that benefit from a clean cutting edge. Thanks to the sharp cutting edge and the small 0.2 mm corner radius, the insert promotes reduced cutting forces and finer finishes, especially on softer alloys and non-ferrous workpieces. The result is efficient material removal with minimal burr formation and less need for subsequent finishing, supporting a smoother production flow. Economic use and extended service life through reversible design Featuring a double-sided chipbreaker, the insert offers two usable cutting edges per side, effectively multiplying usable edges and lowering tooling costs per part. The uncoated carbide substrate delivers reliable edge sharpness where coatings would not be advantageous, and the rhomboid form factor allows economical indexing. Combined with the 4.76 mm thickness and robust seat contact provided by the 80° cutting angle, the geometry supports stable cutting for general turning tasks while keeping tool change frequency low. Practical handling and selection guidance for best results The insert has a 0° relief angle, which must be matched to an appropriate holder geometry to secure the intended clearance and rake behaviour. Choosing the correct chipbreaker variant and the TH10 grade helps to optimise chip control and surface integrity for the intended material. For most standard turning applications, select a compatible ISO holder that accommodates the rhomboid shape and the cylindrical mounting hole to ensure secure clamping and repeatable performance. Contact Metav Werkzeuge for tailored advice on holder compatibility and to secure genuine Tungaloy inserts for reliable production results; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6801855 Manufacturer SKU: TUN6801855 SKU: 6801855-Tungaloy Model series: ISO turning inserts Material: carbide Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.2 mm Cutting angle: 80° Relief angle: 0° ISO code: 120402 Special features Shape: rhomboid Hole: cylindrical hole Chipbreaker: double-sided Grade: TH10 (uncoated carbide) Application: turning (external and internal) FAQ Which materials are best processed with this insert? The TH10 uncoated carbide grade is intended primarily for non-ferrous materials and operations where a sharp edge supports low cutting forces and a clean surface finish; the insert is suitable for a broad range of softer alloys. Is the insert reversible and how many cutting edges are usable? Yes, the rhomboid geometry with a double-sided chipbreaker allows multiple indexing positions; this design extends usable life by providing several effective cutting edges before replacement is needed. How does the 0° relief angle affect holder choice? A 0° relief angle requires selection of a holder designed to provide the required clearance and to match rake and seat geometry; correct holder matching ensures stable cutting and repeatable seating. Does the insert have a coating? This product is supplied as uncoated carbide in the TH10 grade, chosen to maintain a sharp cutting edge where coatings are not beneficial for the process. Which chipbreaker should be selected for optimal performance? The supplied double-sided chipbreaker provides good general-purpose chip control for non-ferrous turning; choose the exact chipbreaker and grade based on material, feed and stability to balance chip shape and surface finish. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 GH110 Wendeplatten - Tungaloy
Take advantage of the combination of wear resistance, edge stability and ISO compatibility to maintain productive turning cycles; the GH110 grade and reversible design reduce tooling costs while sustaining surface quality. Order genuine stock directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. CNGG120404 GH110 — ISO rhombic turning insert for turning, Tungaloy The CNGG120404 GH110 is an ISO rhombic indexable insert designed for external and internal turning applications, with a 0.4 mm nose radius and a double-sided chipbreaker. ISO rhombic insert CNGG120404 GH110 Tungaloy carbide grade 0.4 mm nose radius for fine profiling Double-sided chipbreaker, cylindrical hole Consistent edge life through optimised grade technology The GH110 grade, developed by Tungaloy, combines wear resistance and toughness to preserve cutting-edge geometry under varying cutting conditions. This balance reduces flank wear and maintains dimensional stability over longer tool cycles, which translates into fewer indexings and lower tooling costs per part. The use of carbide as the base material ensures thermal and mechanical stability at standard turning feeds and speeds, and the double-sided design provides two usable edges, improving overall cost-efficiency. Plug-and-produce compatibility for secure clamping and repeatability Compatibility with toolholders follows ISO conventions: shape, relief angle, tolerance class, clamping method, size and thickness determine fit. The rhombic form with an 80° included angle and a 0° relief angle offers flexible approach angles for profiling and general turning. The insert’s cylindrical hole and standard thickness of 4.76 mm support secure mounting in compatible external holders or boring bars, while the 12 mm size makes the geometry predictable in common ISO toolholder systems for immediate integration into existing setups. Process reliability and practical shop-floor advantages A double-sided chipbreaker gives reproducible chip control for many turning tasks; the reversible nature of the insert halves the consumable rate per edge compared with single-sided types. The modest 0.4 mm nose radius is suited to fine profiles and moderate-strength finishing passes, supporting consistent surface quality. For system setup, combine the insert with a matching holder, shim/clamping set and retaining screw to guarantee repeatable clamping force. If clarification on selection or suitability for a specific workpiece material is required, the Metav Werkzeuge technical team is available to advise on the optimal chipbreaker and grade choice for the intended operation. Contact Metav Werkzeuge for expert application advice and to request genuine Tungaloy GH110 CNGG120404 turning inserts to secure reliable, productive turning results Technical data Article number: 6801864 Manufacturer SKU: TUN6801864 Item label: CNGG120404 GH110 Tungaloy insert Model series: ISO-indexable turning inserts Material: Carbide Brand: Tungaloy Facts Thickness: 4.76 mm Size: 12 Nose radius: 0.4 mm Included angle: 80° Clearance angle: 0° Hole: with cylindrical hole Special features Double-sided chipbreaker ISO rhombic form CNGG Compatibility determined by form, relief angle, tolerance class, clamping, size and thickness Intended application: Turning System: insert + holder + shim/clamping set + retaining screw Grade: GH110 (Tungaloy grade) Carbide material Reversible cutting edges FAQ Which applications are best suited to this insert? The CNGG120404 GH110 insert is intended for turning operations where a balance of wear resistance and toughness is required; select the chipbreaker and cutting data according to the specific workpiece material. How is the insert secured in a holder? Compatibility is ensured by matching the insert form, clearance angle, tolerance class, clamping method, size and thickness; the CNGG120404 uses a cylindrical hole for positive clamping in compatible ISO toolholders. Can the insert be indexed to use the second cutting edge? Yes, the insert has a double-sided chipbreaker and is reversible, allowing the second edge to be used to extend effective tool life and reduce consumable costs. What are the key geometry values to note for tooling setup? Key values are a 0.4 mm nose radius and an 80° included angle with a 0° relief angle; the insert thickness is 4.76 mm and the nominal size is 12. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 GH110 Wendeplatten - Tungaloy
Take advantage of the combination of reliable edge stability, balanced wear resistance and ISO compatibility for continuous, productive turning operations. Order the CNGG120404 GH110 indexable insert directly via Metav Werkzeuge or consult the technical team for selection advice. CNGG120404 GH110 indexable insert for turning — Tungaloy CNGG120404 GH110 is an ISO-format rhombic indexable insert designed for a wide range of turning applications, combining a wear-resistant carbide grade with a secure clamping concept for efficient outer and internal turning. ISO-compliant rhombic insert GH110 carbide grade: wear and toughness Double-sided chipbreaker for turning Cylindrical hole for secure clamping Increased productivity through balanced grade and edge stability The GH110 grade from Tungaloy offers a balanced combination of wear resistance and toughness, optimised to complement the insert geometry and cutting-edge stability. This balance reduces the frequency of tool changes and interrupts, which directly improves cycle time and lowers unit machining cost. As an indexable insert in the ISO turning family, the plate supports predictable toollife and consistent surface finish, helping to maintain throughput under varying cutting conditions while allowing straightforward rotation or replacement when wear occurs. Precise geometry for reliable machining results The plate’s rhombic form with an 80° approach angle and a 0.4 mm corner radius provides a versatile cutting edge suitable for finishing and light roughing. A 0° clearance angle and a thickness of 4.76 mm ensure rigidity in the clamping seat, while the 12 mm nominal size matches standard ISO holders. The insert is double-sided, allowing reversible use of the cutting edges, and features a cylindrical hole for positive fastening in compatible tool holders. These geometric details translate into improved repeatability and a clear guideline for selecting compatible holders — form, clearance, tolerance class, fastening and size determine fit. Application guidance and process security Intended for turning, the insert works effectively for both external and internal operations when the correct chipbreaker and cutting parameters are chosen. The double-sided chipbreaker provides controlled chip formation under a range of conditions, lowering the risk of built-up edge and stabilising the cut. For optimal results, match the chipbreaker style and grade to workpiece material, machining type and assembly stiffness; this approach preserves the cutting edge and ensures consistent performance. If further technical data or tailored recommendations are required, Metav Werkzeuge’s consultants can advise on parameter settings and holder compatibility to secure process reliability. Choose the GH110-grade CNGG120404 for stable, productive turning and contact Metav Werkzeuge for customised advice and rapid supply Technical Data Article number: 6801867 Manufacturer SKU: TUN6801867 Model series: ISO turning indexable inserts Material: Carbide Intended use: Turning Facts Corner radius: 0.4 mm Approach angle: 80° Clearance angle: 0° Plate thickness: 4.76 mm Plate size: 12 mm Special features Rhombic plate form Cylindrical hole for fastening Double-sided chipbreaker Carbide grade GH110 (Tungaloy) ISO-format compatibility Suitable for outer and inner turning FAQ What turning tasks is this insert designed for? The CNGG120404 GH110 Tungaloy indexable insert is designed for general turning tasks, covering both external and internal operations when the appropriate chipbreaker and cutting conditions are selected. Which geometric features are most relevant for holder selection? The insert’s rhombic shape, 80° approach angle, 0° clearance, 0.4 mm corner radius and 4.76 mm thickness are the primary dimensions to match the toolholder and ensure correct clamping and cutting geometry for the CNGG120404 GH110. How is the insert secured in the toolholder? Compatibility with a holder is determined by form, clearance angle, tolerance class, fastening method, size and thickness; the CNGG120404 GH110 uses a cylindrical hole for positive clamping in matching ISO holders. Is the cutting edge reversible and how is chip control achieved? The plate is double-sided, enabling use of both faces to extend service life, and the double-sided chipbreaker supports controlled chip formation across a range of turning conditions. What does the GH110 grade mean for machining performance? The GH110 carbide grade from Tungaloy provides a balance between wear resistance and toughness, which supports stable cutting-edge behaviour and consistent performance in varied turning applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 GH110 Wendeplatten - Tungaloy
Take advantage of the combination of balanced wear resistance, stable chip control and straightforward compatibility with ISO toolholders for reliable turning processes; order or request tailored advice from Metav Werkzeuge when exact holder matching is required. CNGG 120404 GH110 indexable turning insert for Turning — Tungaloy A CNGG120404 GH110 indexable turning insert engineered for ISO-compliant external and internal turning operations, offering a compact rhombic form and robust carbide grade. *Rhombic 80° geometry for versatile turning *GH110 grade for wear resistance and toughness *Double-sided chipbreaker for repeatable performance *Cylindrical hole and 0.4 mm corner radius Consistent cutting performance for uninterrupted production The ISO-standard indexable insert delivers predictable performance in serial turning applications. Manufactured from carbide and specified in the GH110 Tungaloy grade, the insert balances wear resistance and toughness, which supports longer in-process life and fewer interruptions. Compatibility with a holder is governed by form, clearance angle, tolerance class, fastening, size and thickness — parameters that determine correct seating and clamping in ISO turning systems. The rhombic 80° geometry and modest 0.4 mm corner radius promote stable cutting forces, helping to maintain dimensional accuracy over tool life. Easy integration into existing ISO toolholders and setups Designed to match common ISO turning systems, the insert’s rhombic shape, 12 mm inscribed circle and 4.76 mm thickness allow simple replacement in compatible external holders or boring bars. The cylindrical hole supports standard clamping and securing mechanisms, while the specified 0° clearance provides a defined contact geometry that helps avoid ambiguous seating. These measurable characteristics reduce setup time and support reproducible positioning, enabling faster changeovers and predictable tool behaviour in multi-shift production environments. Stable chip control and surface consistency The built-in double-sided chipbreaker and the GH110 composition contribute to controlled chip formation and evacuation under a range of turning conditions. Stable chip control reduces risk of surface damage and tool interference, which in turn supports consistent workpiece finish from pass to pass. The combination of geometry and grade is selected to harmonise cutting-edge stability with sufficient toughness, improving process reliability and lowering the need for frequent insert changes — a clear efficiency gain for batch and continuous machining. Practical handling and selection guidance When selecting this insert, pair the CNGG120404 GH110 with a holder that matches the insert form, clearance and tolerance class to guarantee correct seating and optimal cutting angles. The rhombic format and 0.4 mm corner radius are suited to finishing and medium finishing passes where small radii improve surface integrity. The insert’s double-sided layout extends indexable life and reduces inventory needs. For material-specific recommendations or to verify holder compatibility, consult technical advisory resources or the dealer for tailored cutting data. Contact Metav Werkzeuge for expert advice on Tungaloy CNGG120404 GH110 indexable turning inserts — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6801861 SKU: 6801861-Tungaloy Manufacturer SKU: TUN6801861 Designation: CNGG120404 GH110 Tungaloy-Wendeplatte Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Insert angle: 80° Relief/clearance angle: 0° ISO code: 120404 Special features Material: carbide Grade: GH110 (Tungaloy) Chipbreaker: double-sided Hole: cylindrical hole Shape: rhombic Application: turning (external and internal) Model series: ISO indexable turning inserts FAQ What operations is this insert recommended for? The CNGG120404 GH110 insert is designed for ISO-compliant external and internal turning operations where a rhombic geometry and a 0.4 mm corner radius support finishing and medium-finishing passes. How does the GH110 grade affect performance? GH110, as applied by Tungaloy, provides a balance of wear resistance and toughness that promotes stable cutting-edge life and reliable chip control in repeated turning cycles. Is the insert compatible with standard ISO holders? Compatibility depends on holder form, clearance angle, tolerance class, fastening and thickness; the CNGG120404 GH110 fits holders designed for ISO CNGG-type inserts with a 12 mm inscribed circle and 4.76 mm thickness. How should the insert be clamped? The cylindrical hole and ISO geometry allow standard screw or clamp systems used for rhombic indexable inserts; correct clamping relies on matching the holder’s tolerance class and seat geometry. Can the insert be indexed to use both faces? Yes, the insert is double-sided with a chipbreaker on each face, enabling indexing to the second cutting edge to extend usable life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 KS05F Wendeplatten - Tungaloy
Benefit from the combination of wear resistance, edge stability and ISO compatibility for consistently productive turning operations. Order the CNGG120404 KS05F Tungaloy indexable insert via Metav Werkzeuge or request application advice from our specialists. CNGG 120404 KS05F indexable insert for turning — Tungaloy, 80° rhombic, carbide CNGG 120404 KS05F is an ISO-standard rhombic indexable insert designed for external and internal turning where stable cutting edges and repeatable performance are required. ISO-standard CNGG geometry KS05F Tungaloy grade for wear resistance 80° rhombic shape with 0.4 mm radius Double-sided insert with cylindrical hole Reliable edge life and predictable process performance The insert combines the KS05F Tungaloy grade with a carbide substrate to deliver enhanced wear resistance and sustained cutting-edge stability during medium to heavy turning operations. The built-in double-sided chipbreaker promotes consistent chip control, reducing the need for frequent tool changes and supporting steady cycle times. Choosing a grade that balances toughness and hardness means the cutting edge resists chipping while maintaining acceptable flank wear progression, which translates directly into fewer interruptions on the shop floor and improved overall equipment effectiveness. Straightforward compatibility with ISO toolholder systems Engineered to the ISO code 120404, this rhombic insert fits standard CNGG toolholders when matching the form, relief angle, tolerance class, fastening method, size and thickness. The 80° geometry provides good shoulder strength and versatility for external and internal turning, while the cylindrical hole ensures secure clamping. The insert’s 4.76 mm thickness and 12 mm size offer a robust cutting edge, and the 0° relief angle supports a wide range of feeds and depths of cut. This clear ISO alignment simplifies procurement and inventory management across multiple machines and tool families. Practical handling and machining benefits for workshop use With a 0.4 mm radius, the insert offers a defined corner for reliable finishes and predictable toolpath outcomes when profiling or shoulder turning. The rhombic shape allows indexing of multiple cutting edges, extending life per insert and reducing tooling costs in high-volume runs. For operators less familiar with insert grades, the combination of Tungaloy’s engineered composition and the insert’s chip control features provides a forgiving cutting behaviour that aids consistent surface quality and reduces the need for constant parameter adjustments. When optimised cutting data are applied, productivity improves while part quality remains stable. Contact Metav Werkzeuge for tailored cutting-data recommendations and sample availability; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6934781 SKU: 6934781-Tungaloy Manufacturer SKU: TUN6934781 ISO designation: CNGG120404 Model series: ISO-Drehwendeschneidplatten Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Insert angle: 80° Relief (rake) angle: 0° Hole: with cylindrical hole Special features Material: carbide Grade/coating: KS05F (Tungaloy) Chipbreaker: double-sided Shape: rhombic Application: turning (external and internal) Compatibility: ISO-standard insert — fit depends on holder form and tolerances FAQ What materials is this insert suited for? The CNGG120404 KS05F Tungaloy indexable insert is designed for general turning applications; the KS05F grade provides a balance of wear resistance and toughness suitable for a broad range of steels and mixed-material jobs. How does the chipbreaker affect machining? The double-sided chipbreaker on the CNGG120404 helps produce controlled chips and steady metal removal, improving surface quality and reducing cycle interruptions associated with poor chip formation. Can the insert be used in both external and internal turning? Yes, the rhombic geometry and 80° insert angle make the CNGG120404 appropriate for both external and internal turning when paired with the correct ISO-compatible holder. How many cutting edges are available per insert? The CNGG120404 is double-sided and indexable; rotating the insert exposes fresh cutting edges, which extends life per insert and reduces tooling consumption. Which specifications should be matched on the toolholder? Holder compatibility for the CNGG120404 depends on insert form, relief angle, tolerance class, fastening method, size and thickness; ensure the holder matches the ISO CNGG geometry and the 120404 code. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS520 Wendeplatten - Tungaloy
Take advantage of the NS520 cermet grade together with an 80° rhombic geometry and a 0.4 mm corner radius to achieve consistent surface finish and stable dimensional control in finish to light turning operations; order the insert directly via Metav Werkzeuge or request application advice from the consultants. CNGG 120404 NS520 — ISO turning insert for Turning by Tungaloy The CNGG120404 NS520 is an ISO-standard rhombic turning insert designed for finish to light turning of steel, optimised for surface quality and even wear. ISO rhombic 80° geometry NS520 cermet for fine finishing 0.4 mm corner radius Cylindrical-hole, holder compatible Deliver consistent surface quality with a cermet grade built for finishing The combination of the NS520 grade and a cermet substrate provides a cutting edge tailored to finish and light turning of steel, prioritising surface quality and dimensional accuracy. The cermet composition reduces built-up edge formation and promotes even wear, which helps maintain part tolerances over longer tool life. For applications where surface finish is critical, the insert’s geometry and grade contribute to reliable outcomes with reduced need for secondary finishing. Integrates smoothly into ISO turning systems for quick setup Specified as part of the ISO turning insert family, compatibility with toolholders is determined by form, clearance angle, tolerance class, fastening method, size and thickness. The rhombic shape with an 80° included angle and a cylindrical hole supports secure clamping in standard external holders and boring bars, while the 4.76 mm plate thickness provides robust seat support during cutting. Selecting a suitable holder and correct clamping torque ensures repeatable positioning and reduces vibration during operation. Improves process stability and productivity in light turning tasks For finish-oriented turning the insert’s properties reduce the need for conservative feeds and excessive rework. The NS520 cermet grade delivers a balance between edge strength and fine-grain wear characteristics, which can translate into more consistent cycle times and stable surface roughness. The double-sided chipbreaker design allows economical indexing when minor flank wear occurs, extending usable life while maintaining predictable performance across batches. Practical handling guidance and recommended applications With a 0.4 mm corner radius, 12 mm size and a 4.76 mm thickness, this insert is well suited to external and internal finishing passes where dimensional control matters. The rhombic geometry and double-sided chipbreaker are appropriate for steel turning operations that demand good surface integrity. When choosing a chipbreaker and grade, match the NS520 characteristics to workpiece alloy, feed and depth of cut to obtain the best compromise between tool life and surface finish; request detailed cutting data if needed for specific steels. Contact Metav Werkzeuge for delivery and application advice on the Tungaloy NS520 CNGG120404 turning insert — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6801856 Manufacturer SKU: TUN6801856 SKU: 6801856-Tungaloy Model series: ISO-Drehwendeschneidplatten ISO designation: CNGG120404 Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Included angle: 80° Clearance angle: 0° Special features Rhombic insert form Cylindrical hole for clamping Double-sided chipbreaker Grade: NS520 (cermet / coated cermet) Material: carbide Application: Turning Compatible with ISO holders by form, clearance, tolerance, fastening, size and thickness FAQ What materials is this insert suitable for? The CNGG120404 NS520 Tungaloy turning insert is intended primarily for steel finishing operations; the NS520 cermet grade focuses on surface quality and even wear in steel turning. How does the NS520 grade affect finishing performance? NS520 provides a fine-grain cermet characteristic that reduces built-up edge and promotes consistent wear, helping the CNGG120404 NS520 insert to deliver improved surface finish and dimensional control. Which holder types are compatible with this insert? Compatibility depends on holder form, clearance angle and clamping arrangement; the CNGG120404 NS520 insert uses a cylindrical hole and rhombic form to fit standard ISO external holders and appropriate boring bars. Is the insert reversible or indexable? The insert features a double-sided chipbreaker design, enabling economical indexing to extend usable life while maintaining cutting performance for finishing tasks. What are the key geometry values to check when selecting this insert? Key values include the 80° included angle, 0.4 mm corner radius, 12 mm size and 4.76 mm thickness; verify these against the holder and the intended turning operation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS9530 Wendeplatten - Tungaloy
High-precision finishing and steady production are achievable with a sharp, uncoated cermet NS9530 grade combined with ISO compatibility and a compact 0.4 mm nose radius; the result is low cutting forces and superior surface finish for continuous turning of steel. Order the CNGG120404 NS9530 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. CNGG 120404 NS9530 ISO turning insert for finishing — Tungaloy The CNGG120404 NS9530 is an ISO rhombic turning insert engineered for finishing steel, offering a sharp cutting edge and optimised chip control in continuous light-depth passes. Uncoated cermet grade NS9530 Sharp edge delivers fine surface finish 0.4 mm nose radius for precision turning ISO rhombic insert with 80° approach angle Precise finishing with lower cutting forces The combination of an uncoated cermet grade and a finely honed edge makes this insert particularly effective for finishing operations on steel. The NS9530 composition provides a balance between edge sharpness and wear resistance, resulting in low cutting forces and consistent surface quality during continuous cuts and small depth of cut conditions. For applications where surface integrity and dimensional tolerance matter, the fine nose radius and sharp cutting geometry reduce vibration and help achieve repeatable part quality. Predictable compatibility for streamlined tool changes Designed to the ISO turning insert standard, the indexable plate features a rhombic shape and an 80° geometry that align with common external holders and boring bars. Compatibility is governed by form, clearance angle, tolerance class, fastening method, size and thickness, so using standardised holders ensures quick changeover and repeatable clamping performance. The standardised format supports lean toolroom practices by reducing setup time and simplifying inventory management for production environments. Stable mounting and controlled chip formation Mechanical stability is aided by a cylindrical hole for secure fastening and a plate thickness of 4.76 mm, which together provide reliable seating under cutting loads. The double-sided chipbreaker design offers two usable edges, extending the effective economy of the plate while maintaining consistent chip control and surface finish. The modest 0.4 mm nose radius suits fine finishing passes and delicate features, while the overall construction supports predictable tool life and safer machining cycles. For technical advice or availability of Tungaloy CNGG120404 NS9530 finishing inserts, contact Metav Werkzeuge for personalised guidance and order support Technical Data Article number: 6997792 SKU: 6997792-Tungaloy Manufacturer SKU: TUN6997792 Model series: ISO turning inserts ISO designation: CNGG120404 Shape: rhombic Grade: NS9530 Facts Thickness: 4.76 mm Size: 12 mm Nose radius: 0.4 mm Relief angle: 0° Approach angle: 80° Special features Uncoated cermet grade NS9530 Cylindrical hole for secure fastening Double-sided chipbreaker Suitable for finishing steel Compatible with ISO holders based on form and tolerance FAQ What material is the insert best suited for? The CNGG120404 NS9530 insert is a finishing grade designed specifically for steel, providing a sharp edge and low cutting forces for continuous turning operations. How many cutting edges does the plate offer? This indexable plate has a double-sided chipbreaker, giving two usable edges to extend tool economy before replacement. What are the key dimensional specifications to check for holder compatibility? Check size (12 mm), thickness (4.76 mm), relief angle (0°), approach angle (80°) and the cylindrical hole; these determine proper fit in ISO-compatible holders. Is the cutting material coated? The grade is an uncoated cermet (NS9530), optimised for finishing steel with a sharp cutting edge and good surface finish characteristics. What finish quality can be expected with a 0.4 mm nose radius? A 0.4 mm nose radius supports precise finishing passes and helps achieve fine surface finishes while maintaining low cutting forces and reduced vibration. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS9530 Wendeplatten - Tungaloy
Benefit from the combination of precise finishing, stable chip control and ISO compatibility to improve cycle times and surface quality; order the insert directly via Metav Werkzeuge or consult the Metav Werkzeuge team for technical matching. CNGG120404 NS9530 rhombic ISO turning insert, 0.4 mm radius — Tungaloy The CNGG120404 NS9530 is an ISO rhombic indexable insert for external and internal turning, designed as a finishing grade for continuous cuts and small depths of cut. *ISO rhombic insert CNGG120404 *NS9530 uncoated cermet finishing grade *0.4 mm corner radius for fine surface finish *Double-sided chipbreaker with cylindrical hole Consistent finishing with low cutting forces The insert is engineered as an uncoated cermet grade (NS9530) that delivers a sharp cutting edge and low cutting forces, which directly translates into improved machining stability during finishing operations. For turning applications this means fewer chatter issues and more consistent dimensional results, particularly when working with Stahl. The small 0.4 mm radius supports high-quality surface finishes on finishing passes while maintaining predictable tool life, reducing the need for frequent regrinding or replacement and contributing to overall productivity. Reliable fit and stable clamping for repeatable results Built to the ISO plate family, the insert’s rhombic geometry and 80° included angle ensure broad compatibility with common external holders and boring bars; compatibility is governed by form, clearance angle, tolerance class, attachment, size and thickness. The cylindrical hole and double-sided chipbreaker provide secure clamping and extended usable edges, which helps to lower tooling costs per component. With a plate thickness of 4.76 mm and standard ISO designation 120404, the component integrates into typical ISO-turning systems with minimal adaptation, ensuring repeatable set-ups and reduced machine downtime. Practical guidance for efficient turning operations This finishing grade insert is intended for continuous cuts and small depths of cut, making it suitable for fine external and internal profiling where surface integrity is critical. Select a holder and chipbreaker matched to the component material and stability of the set-up; the double-sided chip control assists in managing swarf to avoid surface damage and maintain cycle cleanliness. For uncertain material mixes or to optimise parameters for specific operations with Stahl, Metav Werkzeuge offers application advice to align insert grade, holder geometry and cutting data for best results. Contact Metav Werkzeuge for tailored technical advice on integrating the Tungaloy NS9530 finishing insert into existing tool systems and to arrange supply — email info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Article number: 6997785 SKU: 6997785-Tungaloy Manufacturer SKU: TUN6997785 Manufacturer: Tungaloy Facts Angle: 80° Corner radius: 0.4 mm Plate thickness: 4.76 mm Plate size: 12 mm ISO designation: 120404 Clearance angle: 0° Special features Material: Hartmetall Grade/coating: NS9530 uncoated cermet Shape: rhombic Hole: with cylindrical hole Chipbreaker: double-sided Application: Drehen Model series: ISO-Drehwendeschneidplatten FAQ What types of turning tasks suit this insert best? The CNGG120404 NS9530 insert is optimised for finishing operations in external and internal turning, delivering high surface quality and low cutting forces for continuous cuts. Can this insert be used for different steel alloys? Yes, the NS9530 grade is developed as a finishing sort for Stahl; selecting the correct chipbreaker and machining parameters is essential for best performance across different alloys. How does the double-sided chipbreaker affect tool life? The double-sided design provides additional usable edges and helps with chip control, which extends practical tool life and reduces replacement frequency for the insert. Which holder features ensure correct compatibility? Compatibility depends on form, clearance angle, tolerance class, attachment, size and thickness; ensure the holder matches the ISO form and the cylindrical hole clamping style of the insert. Is the insert ready to fit standard ISO turning systems? The insert follows ISO designation 120404 and fits standard ISO turning systems when paired with the appropriate holder, clamping set and screws. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS9530 Wendeplatten - Tungaloy
Take advantage of the NS9530 cermet finishing grade together with the ISO CNGG120404 form for consistent, high-quality turning results; the combination of 0° clearance and a tight 0.4 mm corner radius reduces cutting forces and improves surface finish. Order the CNGG120404 NS9530 Tungaloy insert directly via Metav Werkzeuge or contact the consultants for compatibility checks. CNGG 120404 NS9530 CNGG turning indexable insert by Tungaloy — ISO finishing insert, 80° geometry The CNGG120404 NS9530 is an ISO-standard indexable insert designed for precision external and internal turning, optimised for fine finishing on steel components. Cermet grade NS9530 for high surface quality ISO CNGG 120404 rhombic insert, 80° geometry 0° clearance, 0.4 mm corner radius, 4.76 mm thick Double-sided chipbreaker with cylindrical hole Consistent finishing with low cutting forces The uncoated cermet NS9530 is formulated for finishing operations on steel, delivering a high surface quality with low cutting forces during continuous cuts and small depth-of-cut applications. Cermet combines ceramic hardness with metallic toughness, which helps maintain a sharp cutting edge longer than many alternatives in fine-turning scenarios. This results in fewer passes to reach tolerance, reduced rework and a measurable improvement in cycle consistency. The grade is especially suitable where a fine surface and tight dimensional control are primary goals. Secure seating and reliable repeatability in the tool system Built to the ISO CNGG 120404 form, the insert's 80° geometry and rhombic shape allow secure clamping in standard holders. The 0° clearance and a 0.4 mm corner radius work together to lower radial cutting loads and improve stability when machining small stepovers or finishing shoulders. The insert is supplied with a cylindrical hole for positive locating and a double-sided chipbreaker that enables reversible use for cost-effective tool life. Where setup repeatability and predictable cutting behaviour are required, this geometry reduces the need for frequent adjustments and shortens machine downtime between tool changes. Practical application guidance for process reliability The insert is intended for turning applications on steel workpieces and is recommended for continuous cuts with small material removals. Compatibility with a holder depends on form, clearance angle, tolerance class, clamping method, size and thickness; pairing the insert with the correct external holder and clamping set ensures the expected performance. The system approach—insert, holder, backing pad and fasteners—supports rapid changeovers and consistent clamping force, which in turn improves repeatable part quality. For best results, select the chipbreaker and grade according to workpiece stability and machining parameters; this approach extends productive cutting time and supports efficient process planning. For specification matching, availability and technical advice on the Tungaloy CNGG120404 NS9530 finishing insert, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to arrange supply and holder compatibility checks Technical Data Article number: 6997787 SKU: 6997787-Tungaloy Manufacturer SKU: TUN6997787 Type designation: CNGG120404 NS9530 Tungaloy indexable insert Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Corner radius: 0.4 mm Thickness: 4.76 mm Inscribed circle/size: 12 mm Included angle: 80° Clearance angle: 0° Hole: with hole (cylindrical) Chipbreaker: double-sided Special features Cutting material: uncoated cermet (NS9530) Application: turning, finishing on steel Insert form: rhombic Compatibility determined by form, clearance, tolerance class, clamping, size and thickness Suitable for continuous cuts and small depth-of-cut finishing operations FAQ What materials is this insert best suited for? The CNGG120404 NS9530 insert is specified as a finishing grade for steel; the NS9530 cermet composition is optimised for producing fine surface finishes on steel workpieces. Can the insert be used on both external and internal turning operations? Yes, the ISO CNGG 120404 form is suitable for both external and internal turning when paired with the appropriate external holder or boring bar. How does the 0° clearance affect cutting performance? A 0° clearance reduces the clearance angle to favour low cutting forces and a true finishing action; in practice this supports better surface finish and stable tool engagement during small-depth cuts. Is the insert reversible and cost-effective for production use? The double-sided chipbreaker allows the insert to be rotated for a second cutting edge, providing cost-effective usage and predictable performance across cycles. Which components are required to assemble a complete cutting system? A complete system consists of the ISO insert, a matching external holder or boring bar, a backing/locking pad or clamping set, and the appropriate fasteners—this ensures correct seating and reliable repeatability in production. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS9530 Wendeplatten - Tungaloy
Combining precise finishing performance with ISO‑standard compatibility and economical use of cutting edges. Order the insert directly via Metav Werkzeuge or request advice from our consultants for process optimisation. CNGG 120404 NS9530 indexable turning insert, rhombic 80° geometry — Tungaloy CNGG 120404 NS9530 is an ISO‑standard indexable insert engineered for finishing turning of steel, offering a sharp edge and low cutting forces in continuous, light‑depth cuts Rhombic insert, 80° cutting geometry Uncoated cermet grade NS9530 for finishing Sharp cutting edge for low cutting forces Double-sided chipbreaker, with hole Achieve superior surface finish with lower machining forces The combination of uncoated cermet grade NS9530 and a finely honed edge delivers a measurable improvement in surface quality during finishing passes. As a finishing grade for steel, the material promotes low cutting forces, which reduces tool‑holder vibrations and helps achieve consistent part tolerances. The small corner radius of 0.4 mm is designed for delicate profile work and tight radii, while the sharp edge geometry supports continuous cut conditions where surface integrity and dimensional accuracy are critical. This results in fewer rework operations and a more efficient production flow. Seamless integration into ISO toolholder systems for reliable setup Produced to ISO dimensions, the insert assures compatibility when the holder is matched by form, clearance, tolerance class, attachment method, size and thickness. The rhombic 80° geometry and 0° clearance angle allow straightforward seating in standard indexable turning holders and boring bars. The plate thickness of 4.76 mm and the standard 12 mm inscribed circle ensure predictable clamping behaviour and repeatable positioning. Clear reference to ISO conformity simplifies tool inventory management and reduces the time spent on tool selection and setup. Controlled chips and practical features for finishing processes The double‑sided chipbreaker improves chip formation in continuous cuts, aiding both process stability and surface finish. The insert is supplied with a cylindrical hole, enabling secure attachment and straightforward indexing; being double‑sided extends usable edge life before the insert must be replaced. Constructed from cemented carbide substrate and utilising a cermet grade, the insert is optimised for small depths of cut and steady feed conditions typical of fine turning operations, balancing tool life and finish quality without coated layers that can blunt a delicate edge. For application advice or to secure availability of the Tungaloy NS9530 finishing insert, contact Metav Werkzeuge for prompt technical support and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Manufacturer article number: 6997788 SKU: 6997788-Tungaloy Manufacturer SKU: TUN6997788 Article name: CNGG120404 NS9530 Tungaloy indexable insert Core measurements Inscribed circle: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 0° Cutting angle: 80° Hole: with hole, cylindrical hole Materials & features Material: cemented carbide substrate Grade: NS9530, uncoated cermet, finishing for steel Chipbreaker: double-sided Suitable application: turning (finishing, continuous cuts) FAQ What is the primary application of this insert? The CNGG 120404 NS9530 Tungaloy indexable insert is designed for turning operations, specifically finishing passes on steel where a sharp edge and low cutting forces are required. Which geometry and dimensions define the insert? The insert features an 80° rhombic geometry, a 0.4 mm corner radius, 4.76 mm thickness and a 12 mm inscribed circle as specified for ISO CNGG 120404. How does chip control work with this grade? Chip control is provided by the double‑sided chipbreaker; the NS9530 uncoated cermet grade supports predictable chip formation in continuous, light‑depth cuts. Is the insert reversible and how is it fixed in the holder? Yes, the insert is double‑sided for two usable edges and is supplied with a cylindrical hole for secure fastening in compatible ISO toolholders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of a dedicated finishing grade, low cutting forces and ISO compatibility for reliable, repeatable turning operations; order the CNGG120404 NS9530 insert directly via Metav Werkzeuge or contact our consultants for specification support. CNGG 120404 NS9530 rhombic turning insert for finishing applications — Tungaloy The CNGG120404 NS9530 is an ISO‑designated rhombic turning insert intended for finishing steel, offering a sharp cutting edge and suitability for continuous cuts in light‑duty turning. ISO‑compatible rhombic insert Uncoated cermet NS9530 finishing grade 0.4 mm corner radius for fine finishing Double‑sided chipbreaker, with cylindrical hole Achieve consistently superior surface finish with low cutting forces The combination of an uncoated cermet matrix and the NS9530 designation is optimised for finishing steel, delivering a high surface finish while keeping cutting forces low. The ground, sharp edge reduces built‑up edge formation during continuous cuts and small depths of cut, so cycle times remain stable and rework is minimised. The built form supports operations where surface integrity and dimensional accuracy are priorities, translating insert properties into measurable process advantages. Reliable clamping and straightforward ISO compatibility Manufactured to an ISO geometry, the rhombic form ensures predictable seat and datum engagement with compatible holders. The geometry features a 4.76 mm thickness, an inscribed circle of 12 mm, and a 0° relief, which together determine stack‑up, rigidity and the accessible cutting depth. The insert is supplied with a cylindrical hole for positive locating and secure fastening; these measurable attributes simplify tool selection and reduce setup variability on production lines. Process recommendations for stable, economical turning The double‑sided chipbreaker design suits continuous turning and assists chip control when paired with appropriate coolant and a rigid toolholder. Use this insert in fine finishing passes with small feed rates to exploit its 0.4 mm radius for improved edge strength and surface quality. For consistent results, match the insert grade and chipbreaker to the workpiece and machining stability — choosing a stable holder and correct clamping torque reduces vibration and extends tool life, contributing to overall process economy. Contact Metav Werkzeuge for tailored cutting data, application advice or to request detailed drawings and compatibility checks for the CNGG120404 NS9530; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Manufacturer article number: 6997791 SKU: 6997791-Tungaloy Manufacturer SKU: TUN6997791 Model series: ISO turning inserts Material: carbide Facts ISO designation: CNGG120404 Size (inscribed circle): 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Relief angle: 0° Included angle: 80° Special features Shape: rhombic Grade: NS9530 Cutting material type: uncoated cermet Chipbreaker: double‑sided Mounting: with hole Hole style: cylindrical Application: turning FAQ What materials is this insert best suited for? The CNGG120404 NS9530 insert is a finishing grade optimised for steel; its uncoated cermet chemistry and sharp cutting edge favour continuous turning operations on steel workpieces. How is the insert clamped and aligned? Alignment and clamping rely on the ISO rhombic datum and the cylindrical hole; the CNGG120404 designation ensures compatibility with holders designed for that ISO geometry and 12 mm inscribed circle. Can this insert be used for roughing? This grade and geometry are intended for finishing passes; the NS9530 finishing grade and 0.4 mm corner radius are not optimised for heavy roughing or interrupted cuts. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp uncoated carbide cutting edge (TH10), a double-sided chipbreaker and ISO‑standard geometry for efficient turning of non‑ferrous components; order the insert directly via Metav Werkzeuge or contact the consultants for application advice. CNGG 120404 TH10 rhomboid turning insert for Drehen — Tungaloy, uncoated carbide, 0.4 mm radius CNGG 120404 TH10 Tungaloy turning insert provides a compact, ISO‑conforming solution for external and internal turning where low cutting forces and clean surface generation are required ISO rhomboid insert, 12 mm size Uncoated carbide grade TH10 for low cutting forces Double-sided chipbreaker, cylindrical hole 0.4 mm corner radius, 0° clearance angle High-efficiency turning for non‑ferrous materials The rhomboid ISO insert delivers predictable performance in conventional turning. The uncoated carbide TH10 grade is engineered for applications with non‑ferrous materials and situations that benefit from a sharp, uncoated edge; this supports reduced cutting forces and contributes to a cleaner surface finish. The insert’s single cutting geometry reduces the need for excessive feed adjustments, which helps to maintain steady cycle times and consistent part quality on lathes and turning centres. Geometry and clamping: dependable fit and repeatable results Designed to ISO dimensions, the insert’s rhomboid form and tolerance class determine compatibility with corresponding holders and boring bars. The cylindrical hole and standard fixing ensure stable seating in the pocket, while the double‑sided chipbreaker allows reversal of the cutting edge for extended productivity. The 0° clearance angle and 0.4 mm corner radius balance edge strength and form accuracy, making the geometry suitable for finishing passes and for operations where delicate edge behaviour is advantageous. Choosing and integrating the insert into the tool system Selection should consider the workpiece material, machining strategy and machine rigidity. The insert forms part of a system that includes the ISO insert, suitable external holder or boring bar and correct clamping set. Because the grade is uncoated carbide, it is particularly useful where low adhesion and minimal built‑up edge are desired. For less experienced engineers, the indexable design simplifies inventory management and reduces downtime through easy rotation or replacement when the edge is worn. For precision turning tasks that prioritise low cutting forces and high surface quality, contact Metav Werkzeuge to discuss the suitability of the Tungaloy CNGG120404 TH10 insert and request tailored recommendations Technical data Article number: 6801858 Manufacturer SKU: TUN6801858 Brand: Tungaloy Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 0° Insert angle: 80° ISO designation: 120404 Special features Material: carbide Grade: TH10 (uncoated) Shape: rhomboid Chipbreaker: double‑sided Hole: with cylindrical hole Application: turning (Drehen) Series: ISO turning indexable inserts FAQ Is this insert suitable for aluminium and other non‑ferrous metals? Yes. The TH10 uncoated carbide grade is intended for non‑ferrous materials and supports low cutting forces and clean surface generation when used as a turning insert. Can the insert be used both externally and internally? Yes. The ISO rhomboid geometry and cylindrical hole allow mounting in compatible external holders and boring bars for both external and internal turning operations. How does the double‑sided chipbreaker affect productivity? The double‑sided chipbreaker enables the insert to be indexed to a fresh cutting edge, extending tool life and reducing tool change frequency for continuous production. What does the 0° clearance angle mean for machining? A 0° clearance angle indicates a neutral relief that, combined with a sharp uncoated edge, helps to reduce cutting forces while maintaining a defined cutting geometry for good surface finish. Which system components are required to use this ISO insert? The insert is part of a system comprising the ISO turning insert, a matching external holder or boring bar, a support/locking kit and replacement fixing screws compatible with the holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120404 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of ISO conformity, a sharp TH10 carbide grade and a secure cylindrical‑hole mount for consistent, low‑force turning and clean surface results; order directly via Metav Werkzeuge or consult the team for compatibility checks. CNGG 120404 TH10 ISO turning indexable insert by Tungaloy The CNGG120404 TH10 is an ISO rhombic indexable insert designed for external and internal turning, providing a low cutting‑force uncoated carbide edge and double‑sided chipbreaker for dependable surface quality. ISO rhombic insert CNGG 120404 Uncoated carbide grade TH10 Double-sided chipbreaker for clean finishes Cylindrical-hole mounting, 0° relief Increased process efficiency through low cutting forces The rhombic indexable insert in TH10 grade is an economical choice for operations that prioritise reduced cutting resistance and improved surface finish when machining non‑ferrous and low‑force applications. The uncoated carbide edge supports smoother shearing, which often means lower spindle loads and extended tool life in light‑duty turning. Where cutting energy and heat generation must be kept down, this configuration enables more consistent cycle times and less frequent interruption for insert changes, supporting higher throughput on smaller batches. Secure clamping and ISO compatibility for reproducible results Manufactured to the ISO designation CNGG 120404, the insert’s form, tolerance and cylindrical hole ensure compatibility with standard external holders and boring bars. The 0° relief and the 80° lead geometry enable predictable seating and repeatable cutting geometry across sets, so toolmakers and operators can match holders and clamping kits with confidence. This deterministic compatibility reduces set‑up time and variances in part quality during serial production. Application suitability and handling advantages With a double‑sided chipbreaker and a 0.4 mm corner radius, the insert is tailored for turning operations where tidy chip formation and controlled cutting are required. The geometry supports both external and internal turning tasks, and the insert’s thickness and size yield stable contact and good support in the pocket. For workshops that process aluminium, brass and other non‑ferrous materials, the uncoated cutting edge helps to prevent built‑up edge and to maintain a clean surface without the need for aggressive coatings. Simple system integration and maintenance benefits The insert is part of a system comprising the ISO plate, matching holder or boring bar, support/clamping set and spare screws. As a double‑sided component, it offers cost‑effective indexing and reduces consumable changes per part produced. Clear specification of size, thickness and hole style simplifies spare‑parts management and ensures fast replacement in a production environment, supporting consistent quality with minimal downtime. Contact Metav Werkzeuge to discuss Tungaloy TH10 inserts, confirm holder compatibility or request a cutting data recommendation — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 6801869 Manufacturer SKU: TUN6801869 SKU: 6801869-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: CNGG120404 Material: Hartmetall Grade: TH10 Application: Drehen Facts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.4 mm Lead angle: 80° Relief angle: 0° Special features Rhombic plate form Cylindrical hole style Double-sided chipbreaker Uncoated carbide cutting edge Compatibility depends on form, relief, tolerance, fastening, size and thickness Typical use: external and internal turning System components: matching holder/boring bar, support/clamping set, spare screws FAQ What materials is this insert suitable for? The CNGG120404 TH10 Tungaloy indexable insert (SKU 6801869-Tungaloy) is optimised for non‑ferrous materials and applications that benefit from a sharp uncoated carbide edge and reduced cutting forces. Is the insert reversible or single‑use per edge? The CNGG120404 is double‑sided; each side can be indexed to provide two cutting edges, which enhances cost efficiency for turning operations. How is the insert fixed to the holder? This insert features a cylindrical hole for secure mounting; compatibility with a holder is determined by form, relief angle, tolerance class, fastening method, size and thickness. Can the insert be used for both external and internal turning? Yes, the geometry and chipbreaker design suit both external and internal turning tasks when paired with the appropriate holder or boring bar. What are the key dimensional specifications to check before ordering? Verify size (12 mm), thickness (4.76 mm), corner radius (0.4 mm), lead angle (80°) and relief (0°) to ensure correct fit and function. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CNGG 120404 TH10 Wendeplatten - Tungaloy
Take advantage of a proven ISO-compatible design combined with a sharp, uncoated carbide grade to reduce cutting forces and improve surface finish in general turning operations. Order the insert directly via Metav Werkzeuge or consult the team for holder compatibility and clamping recommendations. CNGG 120404 TH10 — Indexable turning insert for turning by Tungaloy CNGG120404 TH10 Tungaloy turning insert is an ISO-indexed, rhombic insert engineered for external and internal turning where low cutting forces and clean surfaces are required ISO-indexed CNGG geometry for broad compatibility Uncoated carbide TH10 for low cutting forces Rhombic shape with 80° approach angle 0.4 mm nose radius for fine surface finish Double-sided chipbreaker with cylindrical hole Consistent cutting with a sharp, universal grade The combination of an ISO-standard geometry and the TH10 uncoated carbide grade provides predictable cutting behaviour across a wide range of non-ferrous and delicate applications. The sharp edge reduces required cutting force, which helps to limit deflection on less rigid setups and supports a clean surface finish. Uncoated grades are especially suitable where adhesion or built-up edge risk must be minimised and where a defined cutting edge is preferred over coated alternatives. Geometry that supports precision and repeatability A 0.4 mm nose radius paired with the 80° approach angle and the rhombic plate form delivers a balance between profile strength and fine finishing capability. The specified nose radius directly influences surface roughness and allowable feed rates: a smaller radius helps achieve tighter finishes with lower feed, while the 80° geometry gives a reliable cutting direction for both facing and longitudinal turning. These features contribute to repeatable results when the rest of the machining system is appropriately selected. Secure mounting and system compatibility explained Compatibility with the toolholder is governed by the insert’s form, relief angle, tolerance class, fastening method, size and thickness; the presence of a cylindrical hole supports positive location and firm clamping. With a 4.76 mm thickness, the insert provides sufficient stability in standard external holders and boring bars when clamped correctly. The double-sided chipbreaker extends usable life by allowing indexation of the insert, helping maintain process uptime. Application suitability and chip control guidance The grade is intended as a sharp, universal solution for non-ferrous materials and for operations that benefit from a clean, uncoated cutting edge. The double-sided chipbreaker is designed to manage chips on a variety of workpiece materials provided the appropriate chipbreaker variant and cutting parameters are selected. For best results, choose a chipbreaker and grade that match the part material, machining strategy and machine-tool rigidity. Practical system approach for production stability An indexable insert performs best as part of a system: the insert, a matched external holder or boring bar, a support shim or clamp set and the correct fastening screw together determine the operational reliability. Ensuring the holder accepts the CNGG form and the specified clearance is essential; incorrect holder selection is a common source of vibration or poor surface finish. The ISO-series design simplifies holder selection by adhering to established geometric standards. Setup tips to reduce trial-and-error Select the TH10 grade and the double-sided chipbreaker when low cutting forces and clean finishes are priorities; for heavier interrupted cuts or harder materials, consider a different grade or a coated alternative. Check the holder’s tolerance class and ensure the clamping screw and underlay match the insert thickness. For further matching of holder geometry and process parameters, technical consultation is recommended to avoid unnecessary tool wear or poor surface results. Contact Metav Werkzeuge to confirm holder compatibility, request application advice and secure the correct CNGG 120404 TH10 inserts for productive turning operations Technical data Article number: 6801863 Manufacturer SKU: TUN6801863 SKU: 6801863-Tungaloy Designation: CNGG120404 TH10 Tungaloy insert Model series: ISO turning indexable inserts Material: carbide Dimensions & measurable data Plate size: 12 mm Plate thickness: 4.76 mm Nose radius: 0.4 mm Relief/clearance angle: 0° Approach angle: 80° Hole style: cylindrical hole Designs & special features Plate form: rhombic Chipbreaker: double-sided Grade/coating: TH10 uncoated carbide Application: turning (external and internal) Compatibility: holder fit depends on form, relief angle, tolerance, fastening, size and thickness FAQ Is this insert suitable for both external and internal turning? Yes. The CNGG120404 TH10 insert is designed for both external and internal turning when used with a compatible external holder or boring bar and the appropriate clamping set. Which materials are best machined with the TH10 grade? The TH10 uncoated carbide grade is optimised for non-ferrous materials and operations requiring low cutting forces and clean surfaces; it performs well where a sharp, uncoated edge is advantageous. How does the 0.4 mm nose radius affect surface finish? A 0.4 mm nose radius helps achieve finer surface finishes at lower feeds and reduces the risk of workpiece indentation compared with larger radii; selection should match the intended feed rates and part tolerance. What determines whether the insert fits a specific holder? Fit is determined by the insert form, relief angle, tolerance class, fastening method, size and thickness; ensure the holder accepts the CNGG geometry and 4.76 mm plate thickness. Can the insert be indexed to use both sides? Yes. The insert is double-sided with a chipbreaker design that allows indexation to the second cutting edge, extending tool life and minimising downtime. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 GH110 Wendeplatten - Tungaloy
Take advantage of the combination of ISO‑standard compatibility, GH110 Tungaloy wear resistance and a compact rhombic geometry for consistent turning results; order the insert directly via Metav Werkzeuge or request application advice from our consultants. CNGG120408 GH110 indexable insert for turning by Tungaloy — rhombic, 12 mm, with cylindrical hole The CNGG120408 GH110 is an ISO‑standard rhombic indexable insert designed for general external and internal turning, offering robust edge stability and straightforward interchangeability with matching holders. ISO-standard CNGG insert, 12 mm size GH110 Tungaloy grade for wear resistance Rhombic shape with 0° clearance angle Cylindrical through-hole and 0.8 mm corner radius Engineered for dependable turning performance The insert is built on a carbide substrate combined with the GH110 Tungaloy grade, providing a balance of wear resistance and edge toughness that translates into longer service life and stable surface finishes. In practice, this means fewer interruptions for regrinding or replacement and more predictable process control on the shop floor. The rhombic geometry and precise ground faces deliver consistent contact with the clamping system, which helps maintain repeatable cutting conditions and reduces variation between parts. Designed for secure mounting and system compatibility Manufactured to ISO dimensions, the insert’s form, clearance angle and tolerance class ensure compatibility with widely used external holders and boring bars. The presence of a cylindrical through-hole simplifies positive locating and clamping, while the specified 4.76 mm thickness and 12 mm size keep the insert stable under moderate cutting forces. Clear mechanical interfaces reduce set‑up time and enable rapid index changes, which is particularly valuable in mixed‑batch production where tool changes must be fast and reliable. Practical selection for varied turning tasks Equipped with a double-sided chipbreaker, the insert suits a range of turning operations; selecting the appropriate chipbreaker and the GH110 grade according to workpiece material and machining conditions optimises results. The geometry is appropriate for both external and internal turning cycles where a controlled chip flow and edge stability are required. For operators assessing options, the insert’s balanced properties make it a pragmatic choice where a combination of surface quality and tool life is sought. Shop-floor benefits and handling As an indexable solution, the insert contributes to efficient tool management and predictable downtime planning. The 0.8 mm corner radius offers a compromise between edge strength and achievable surface finish, while the standardised ISO form simplifies inventory and reduces the assortment of holders required. System assembly typically comprises the insert, a compatible outer holder or boring bar, a clamp plate or clamp set and replacement screws, enabling straightforward maintenance and quick turnarounds during production shifts. For demanding turning operations, select the Tungaloy GH110 CNGG120408 insert and contact Metav Werkzeuge for availability and tailored application advice: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: 6801879 Manufacturer SKU: TUN6801879 SKU: 6801879-Tungaloy Model series: ISO turning indexable inserts Facts Insert size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Clearance angle: 0° Insert angle: 80° Through-hole: cylindrical Special features Shape: rhombic Grade/coating: GH110 (Tungaloy) Chipbreaker: double-sided Substrate: carbide Intended application: turning Mounting: with cylindrical through-hole ISO designation: CNGG120408 Typical system components: outer holder, boring bar, clamp set, replacement screws FAQ What operations is this insert suitable for? The CNGG120408 GH110 Tungaloy indexable insert (SKU: 6801879-Tungaloy) is intended primarily for external and internal turning where a balance of wear resistance and edge stability is required. How does the GH110 grade affect tool life? The GH110 Tungaloy grade provides improved wear resistance and reliable edge behaviour, so the CNGG120408 insert typically yields longer effective cutting life compared with less wear‑resistant grades. Which holders are compatible with this ISO insert? Compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness; the insert’s ISO dimensions allow fitting to standard holders and boring bars designed for CNGG‑style inserts. Can this insert be used for interrupted cuts? The carbide substrate and GH110 grade of the CNGG120408 insert offer a compromise of toughness and wear resistance that can handle light to moderate interrupted cuts if the overall machining set‑up provides sufficient rigidity. What is the advantage of the cylindrical through‑hole? The cylindrical through‑hole in the CNGG120408 insert enables positive locating and stable clamping, which improves repeatability and helps maintain consistent cutting geometry across tool changes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 GH110 Wendeplatten - Tungaloy
Benefit from the combination of GH110 wear resistance, a double-sided chipbreaker and full ISO compatibility for predictable, productive turning operations. Take advantage of the rhombic form and stable clamping to maintain surface quality and tool life. Order the insert via Metav Werkzeuge or consult the specialists for application support. CNGG 120408 GH110 – Tungaloy indexable insert for turning The CNGG 120408 GH110 is an ISO-standard indexable insert designed for external and internal turning, offering a balanced combination of wear resistance and edge stability for general turning tasks. ISO-standard rhombic insert CNGG 120408 GH110 Tungaloy grade for wear resistance Double-sided chipbreaker for versatile cutting Cylindrical hole and 0° clearance for stability Stable cutting performance through optimised grade and substrate The insert is produced in cemented carbide with the manufacturer’s GH110 grade, delivering a deliberate balance between hardness and toughness that supports consistent performance under varying cutting conditions. This material choice reduces flank wear and helps preserve the cutting edge across extended tool life, which translates into fewer indexings and reduced process interruptions. The combination of rhomboid geometry and the selected substrate promotes predictable chip formation and helps to maintain surface finish without frequent regrinding. Where cycle time and repeatability matter, the indexable insert offers measurable gains in productivity and process stability. ISO compatibility for straightforward holder integration As an ISO-specification insert, compatibility with a suitable toolholder depends on the insert form, clearance angle, tolerance class, fastening method, size and thickness. The standardised dimensions simplify holder selection and spare-part logistics across production cells. The rhombic shape and a cylindrical central hole enable reliable clamping in matched holders; the 0° clearance reduces the need for special seat geometries. Clear reference to the ISO code helps machining planners ensure correct seating and torque values for the clamping screw, thereby avoiding uncertain fits. This alignment reduces setup time and contributes to reproducible machining results. Designed for repeatable chip control and operator confidence The double-sided chipbreaker and the moderate nose radius work together to control chip formation and evacuation, which is especially useful in mixed-material turning tasks. The insert’s geometry supports consistent cutting forces and enhances edge stability when interrupted cuts or variable feeds are required. The CNGG 120408 accommodates a range of turning strategies — from light finishing passes to more aggressive semi-finishing — while the central cylindrical hole ensures secure mounting and minimal movement under load. For production lines seeking a dependable balance of surface quality and tool life, this insert provides a pragmatic, application-oriented solution. Contact Metav Werkzeuge for application advice on the Tungaloy CNGG 120408 GH110 insert and current availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6801875 Manufacturer SKU: TUN6801875 SKU: 6801875-Tungaloy Facts Grade: GH110 (Tungaloy) Material: cemented carbide Insert designation: CNGG120408 Shape: rhombic Size: 12 mm Thickness: 4.76 mm Nose radius: 0.8 mm Clearance angle: 0° Lead angle: 80° Hole: cylindrical Special features Double-sided chipbreaker ISO indexable turning insert series Suitable for external and internal turning Tungaloy cutting grade tailored for wear resistance and edge stability FAQ What materials is this insert suited for? The GH110 grade is designed for general turning tasks; the Tungaloy CNGG 120408 insert performs well across a wide range of steels and common engineering materials due to its balanced wear resistance and toughness. How is the insert clamped in the holder? The insert features a cylindrical central hole and standard ISO dimensions; secure clamping is achieved with the corresponding holder, matching form and thickness to ensure stability. Can the insert be used for internal boring as well as external turning? Yes, the ISO rhombic form and double-sided chipbreaker make the insert suitable for both external and internal turning operations when paired with the appropriate holder. How does the double-sided chipbreaker improve process reliability? The double-sided chipbreaker promotes consistent chip formation and evacuation on both index positions, helping to maintain stable cutting forces and extend edge life under varying cutting conditions. Which identifier should be quoted when ordering replacement inserts? Use the designation CNGG120408 GH110 and the article number 6801875 or SKU 6801875-Tungaloy to ensure the correct item is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 KS05F Wendeplatten - Tungaloy
Take advantage of the ISO‑compliant geometry and the KS05F Tungaloy grade for a balance of wear resistance and edge stability; the rhombic 80° form with a 0.8 mm nose radius provides reliable profile control in both external and internal turning. Order the CNGG120408 KS05F Tungaloy insert directly via Metav Werkzeuge or consult our technical team for machining recommendations. CNGG120408 KS05F — Indexable turning insert (rhombic 80°, 0.8 mm radius) | Tungaloy The CNGG120408 KS05F is an ISO‑compliant rhombic indexable insert engineered for external and internal turning applications, compatible with appropriately dimensioned holders and clamping systems. ISO‑compliant rhombic insert 12 mm KS05F Tungaloy grade for wear resistance 0.8 mm nose radius for precise profiling Double‑sided chipbreaker with cylindrical hole Geometry that delivers predictable cutting performance The rhombic 80° geometry combined with a 0° clearance creates a robust seating and approach angle that is well suited to a wide range of turning tasks. The defined 0.8 mm nose radius supports accurate contouring and repeatable profile work, while the ISO conformity ensures straightforward interchangeability with standard indexable holders. Because compatibility depends on holder form, relief angle, tolerance class, clamping method, size and thickness, this geometry reduces uncertainty at setup and helps maintain consistent component tolerances during production. A Tungaloy grade chosen for productivity and tool life The KS05F cutting grade is formulated to balance wear resistance and edge toughness, extending service life under mixed machining conditions. Combined with the insert's double‑sided chipbreaker, the grade helps control chip form and heat at the cutting edge, which supports longer periods between indexings and lowers tooling costs per part. For operations seeking economical, repeatable results, this composition offers a pragmatic route to higher process uptime and steady surface quality. Precise dimensions for reliable system integration With a nominal size of 12 mm and a plate thickness of 4.76 mm, the insert fits standard ISO‑type turning systems where stable clamping is required. The inclusion of a cylindrical hole facilitates positive positioning and consistent clamp engagement; the specified dimensions aid in achieving repeatable concentricity and reduced set‑up time. Clear, measurable parameters make it easier to document tooling data in CAM systems and tool libraries, supporting quicker changeovers and reliable batch production. Practical guidance for application and process optimisation Designed for turning, the insert performs best when the chipbreaker and grade are selected to match workpiece material, cutting strategy and machine rigidity. The ISO format allows simple comparison of alternative geometries and grades when process conditions change. Where higher stability is required, the robust carbide construction combined with KS05F's balanced properties helps maintain edge integrity and surface finish. If additional machining data is needed, technical consultation is recommended to align insert choice with spindle power, feed strategy and desired surface requirements. Contact Metav Werkzeuge to discuss the CNGG120408 KS05F Tungaloy insert and receive tailored machining recommendations from our technical consultants Technical Data Article number: 6934785 Manufacturer SKU: TUN6934785 Designation: CNGG120408 KS05F Tungaloy‑Wendeplatte Model series: ISO‑Drehwendeschneidplatten Manufacturer: Tungaloy Core data Size: 12 mm Thickness: 4.76 mm Nose radius: 0.8 mm Geometry angle: 80° Clearance angle: 0° Special features ISO‑compliant rhombic insert Double‑sided chipbreaker Tungaloy grade KS05F Carbide body Cylindrical hole for positive clamping Intended for turning (external and internal) FAQ What holder characteristics determine compatibility with this insert? Compatibility is determined by holder form, relief angle, tolerance class, clamping method, size and plate thickness; the CNGG120408 KS05F insert requires a matching ISO‑compliant turning holder for correct seating and secure clamping. Which applications are best suited to the KS05F grade? The KS05F Tungaloy grade in the CNGG120408 insert is aimed at turning applications where a balance of wear resistance and edge toughness is needed, providing stable performance across varied machining conditions. How does the double‑sided chipbreaker affect tool life? A double‑sided chipbreaker offers two cutting edges per indexed position and improved chip control, which can increase cutting intervals and reduce tooling cost per component when using the CNGG120408 KS05F insert. Can the 0.8 mm nose radius be used for finishing passes? Yes; the 0.8 mm radius provides a compromise between profile definition and edge strength, making the insert suitable for medium finishing and profiling operations while retaining edge stability. Which identification numbers should be referenced when ordering? Reference the designation CNGG120408 KS05F and the article number 6934785 or manufacturer SKU TUN6934785 to ensure the correct Tungaloy indexable insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 NS520 Wendeplatten - Tungaloy
The Cermet NS520 grade and the rhombic ISO form deliver a consistent surface finish and reliable dimensional control, while the double-sided geometry and cylindrical hole provide economical indexability and secure clamping; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CNGG 120408 NS520 — ISO indexable turning insert by Tungaloy, rhombic 80° form, 0.8 mm corner radius A CNGG120408 NS520 indexable insert engineered for finishing to light turning of steel, offering a coated cermet cutting grade optimised for surface quality and uniform wear Cermet grade NS520 for superior surface finish Double-sided insert for economical indexability Rhombic form CNGG with 80° cutting angle 0.8 mm corner radius with cylindrical hole interface Consistent surface quality from a specialised cermet grade The first benefit of this insert is its focus on finish and repeatability: the NS520 cermet composition combines high hardness with a metal binder to produce a fine surface and steady wear behaviour. For finishing and light turning of steel, this material class reduces built-up edge and supports dimensional accuracy across longer tool life. The result is fewer reworks and more predictable component tolerances, particularly where surface integrity and tight limits matter. Secure clamping and efficient indexability for production Designed as an ISO-standard indexable insert, the plate features a cylindrical hole and a double-sided chipbreaker arrangement that enable two usable cutting edges per insert and dependable seating in compatible holders. Compatibility with the clamping system is determined by the insert’s shape, clearance angle (0°), tolerance class, fastening method, size (12 mm) and thickness (4.76 mm). The rhombic form with an 80° included angle gives a balanced compromise between strength and accessibility for external and internal turning setups. Application fit and process guidance for steel machining This grade is intended for finishing to light turning of steel, prioritising surface finish and consistent wear rather than heavy material removal. Operators should match the chipbreaker and grade to the machining stability and the component’s surface requirements. Selecting the appropriate feed and cutting speed will preserve the cermet’s advantages: improved surface integrity and predictable tool consumption. Where higher removal rates are required, consider alternative geometries or grades better suited to roughing. For reliable finishing performance choose the Tungaloy CNGG120408 NS520 indexable insert — contact Metav Werkzeuge for tailored recommendations or order directly; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details Technical Data Article number: 6801870 SKU (manufacturer): TUN6801870 Our SKU: 6801870-Tungaloy Designation: CNGG120408 NS520 Tungaloy indexable insert Material: carbide (cermet/coated cermet option) Core Data ISO series: ISO indexable turning inserts Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Clearance angle: 0° Included angle / form: rhombic, 80° Hole: with cylindrical hole Chipbreaker: double-sided Special features Cermet grade NS520 optimised for finish and uniform wear Double-sided geometry for two indexable edges ISO-compatible: form, clearance, tolerance and thickness determine holder fit Typical use: finishing to light turning of steel System comprises insert, matching external holder or boring bar, backing/clamping kit and replacement screws (holder and accessories not included) FAQ What materials is this insert best suited for? The insert is formulated as a cermet NS520 grade and is best suited for finishing to light turning of steel, offering improved surface quality and consistent wear for steel applications. How many cutting edges are available per insert? The double-sided geometry provides two usable cutting edges per indexable insert, allowing economical reindexing before replacement. Which holder types are compatible with this plate? Compatibility is determined by ISO form, clearance angle (0°), tolerance class, fastening and thickness; the plate seats in holders designed for rhombic CNGG 120408 inserts with a cylindrical hole. Does the insert require a specific chipbreaker selection? Yes, chipbreaker choice should match workpiece material, machining type and machine stability; the supplied double-sided breaker suits finishing and light turning tasks. What is the significance of the NS520 designation? NS520 denotes a cermet cutting grade optimised for surface finish, dimensional control and even wear behaviour during finishing operations in steel. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 NS9530 Wendeplatten - Tungaloy
Take advantage of a finishing-grade uncoated cermet designed for low cutting forces and excellent surface finish; the combination of 80° rhombic geometry and a 0.8 mm corner radius ensures stable, repeatable turning results in continuous cuts — Order the CNGG120408 NS9530 insert directly via Metav Werkzeuge or ask our consultants if needed. CNGG 120408 NS9530 ISO turning insert — finishing for steel by Tungaloy The CNGG120408 NS9530 is an ISO-standard rhombic turning insert tailored for finishing operations on steel, featuring a sharp cermet grade for low cutting forces and high surface quality. Finishing cermet for steel Sharp edge with low cutting forces Rhombic 80° geometry 0.8 mm corner radius Predictable finishing performance with a sharp cermet grade The finishing uncoated cermet NS9530 provides a consistently sharp cutting edge that reduces cutting forces and improves surface integrity on steel. As a consequence, operators can achieve a finer surface finish with smaller depths of cut and continuous cutting conditions; this is particularly beneficial where dimensional accuracy and minimal post-process work are priorities. The material choice suits applications where thermal stability and edge acuity matter more than heavy interrupted cuts, offering efficient material removal while maintaining excellent part appearance. ISO conformity and holder compatibility for reliable machining The insert follows the ISO CNGG120408 designation and is manufactured with the standard form, relief angle and thickness that define compatibility with matching toolholders. Correct pairing depends on form, relief angle, tolerance class, fastening method, size and thickness — selecting a compatible 80° rhombic holder ensures secure clamping and repeatable positioning. Using the correct assembly reduces vibration, improves tool life and simplifies tool changeover in serial production environments, supporting process stability and predictable cycle times. Stability and chip control that support surface quality A 0.8 mm corner radius and a plate thickness of 4.76 mm provide the rigidity needed for finishing passes; the combination reduces deflection at small feed rates and promotes consistent edge engagement. The insert’s double-sided chipbreaker geometry aids chip control under continuous cutting conditions, while the cylindrical locating hole improves clamping accuracy in compatible holders. These design elements together mean fewer interruptions from poor chip flow and a more consistent surface finish across batches. Application guidance and practical advantages for the workshop Designed primarily for turning steel in finishing operations, this ISO insert is best applied with small radial depths and continuous cuts to exploit the sharp cermet grade. The uncoated cermet is optimised for low cutting forces and fine finishes rather than heavy roughing or highly interrupted work; selecting the appropriate chipbreaker and matching the insert grade to the workpiece material and machining stability will extend performance. For operators seeking predictable surface results and straightforward insertion into standard ISO tool systems, this insert delivers an efficient, production-oriented solution. Contact Metav Werkzeuge to discuss the suitability of the Tungaloy CNGG120408 NS9530 insert for specific turning tasks and to obtain availability and technical advice Technical data Article number: 6997790 SKU: 6997790-Tungaloy Manufacturer SKU: TUN6997790 Brand: Tungaloy Model series: ISO turning inserts Facts Corner radius: 0.8 mm Included angle: 80° Relief angle: 0° Thickness: 4.76 mm Size: 12 mm Special features ISO designation: CNGG120408 Grade: NS9530 (uncoated cermet) Plate shape: rhombic Chipbreaker: double-sided Hole style: cylindrical hole Typical application: finishing turning on steel FAQ What materials is this insert suitable for? The CNGG120408 NS9530 insert is designed primarily for finishing operations on steel, with the NS9530 uncoated cermet optimised for low cutting forces and high surface quality. Which geometry and radius does the insert have? This ISO insert uses an 80° rhombic geometry with a 0.8 mm corner radius, providing a balance between edge strength and fine-surface capability. Is the insert indexable and how is it secured? The insert is double-sided with a cylindrical locating hole and is intended for use in compatible ISO holders that match form, size, thickness and fastening method. Can this grade be used for roughing or interrupted cuts? The NS9530 finishing grade is optimised for continuous cuts and small depths of cut; it is not primarily intended for heavy roughing or heavily interrupted machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precise finishing performance, uncoated cermet NS9530 sharp-edge geometry and reliable ISO compatibility for consistent turning results; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CNGG120408 NS9530 indexable insert for Turning — Tungaloy (80° rhombic, 0.8 mm radius) CNGG120408 NS9530 is an ISO-format rhombic turning insert designed for external and internal finishing cuts where low cutting forces and high surface quality are required. *ISO-format rhombic insert, 80° angle *Uncoated cermet NS9530 for fine finishing *Double-sided geometry, cylindrical hole *Compatible with standard ISO toolholders Delivering consistent fine finishing with lower cutting forces The uncoated cermet NS9530 grade is formulated for finishing operations on steel, providing a sharp cutting edge and reduced built-up edge tendency. This results in lower cutting forces and improved dimensional control during continuous cuts and small depths of cut, making the insert suitable for high-quality surface requirements. The combination of the grade and edge geometry is intended to produce a high surface finish with predictable tool life under stable machining conditions. Secure mounting and broad holder compatibility for process reliability The insert is manufactured to ISO dimensions, with compatibility to a toolholder determined by form, relief angle, tolerance class, fastening, size and thickness. The rhombic 80° shape and cylindrical hole ensure repeatable indexation and clamping stability when used with standard clamping sets and screws. This standardised system design enables straightforward integration into existing turning setups and helps to reduce changeover times while maintaining machining accuracy. Geometry and dimensions optimised for finishing applications Key dimensions — size 12, thickness 4.76 mm and corner radius 0.8 mm — are chosen to balance edge strength and the fine-profile capability required for finishing. The 0° relief angle and double-sided configuration increase economical use by providing two cutting edges per index. Material selection and chipbreaker form are matched to continuous turning tasks, and the insert is supplied in the ISO CNGG format to simplify tool selection and ensure predictable behaviour in serial production. Contact Metav Werkzeuge for tailored machining recommendations and to request the Tungaloy CNGG120408 NS9530 insert or detailed technical data Technical Data Article number: 6997789 Manufacturer SKU: TUN6997789 SKU: 6997789-Tungaloy Model series: ISO-Drehwendeschneidplatten Brand: Tungaloy Material: Hartmetall Application: Drehen ISO designation: CNGG120408 Grade: NS9530 Core dimensions Size: 12 mm Thickness: 4.76 mm Corner radius: 0.8 mm Included angle: 80° Relief angle: 0° Hole style: cylindrical Special features ISO-format rhombic insert Uncoated cermet cutting grade NS9530 Double-sided geometry Cylindrical central hole for secure clamping Designed for external and internal finishing FAQ What materials is this insert intended for? The CNGG120408 NS9530 insert is specified for finishing on steel; the uncoated cermet NS9530 is optimised for continuous cuts and small depths of cut to achieve superior surface quality. How does the insert mount to a toolholder? Mounting is achieved via the cylindrical hole and standard ISO clamping arrangements; compatibility depends on form, relief angle, tolerance class, fastening method, size and thickness, ensuring a secure fit in compatible holders. How many cutting edges are available per insert? The geometry is double-sided, providing two usable cutting edges per indexation, which improves cost-efficiency for finishing applications. What are the key dimensions to check when selecting a holder? Important dimensions to match are the size 12, thickness 4.76 mm, corner radius 0.8 mm and the 80° included angle to ensure correct seating and clearance. Is this insert suitable for roughing operations? This grade and geometry are optimised for finishing; for heavy roughing a grade and geometry designed for higher robustness would be preferable over the NS9530 finishing sort. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 NS9530 Wendeplatten - Tungaloy
Benefit from the combination of the NS9530 finishing grade, a 0.8 mm corner radius and ISO compatibility for reliable, high-quality turning results; order the insert directly via Metav Werkzeuge or consult our experts for process advice. CNGG120408 NS9530 Tungaloy ISO indexable turning insert, rhombic, 80° for turning The CNGG120408 NS9530 is an ISO indexable turning insert designed for finishing operations on steel, offering a sharp cutting edge and a geometry optimised for continuous cuts ISO indexable turning insert, 80° geometry Uncoated cermet grade NS9530 0.8 mm corner radius for high surface finish Cylindrical hole, double-sided chipbreakers Consistent finishing and reduced cutting forces The NS9530 grade is an uncoated cermet engineered for fine finishing on steel, delivering a sharp cutting edge that reduces ploughing and results in low cutting forces. This behaviour leads directly to improved surface quality and repeatable cylindricity when performing light, continuous cuts. For users unfamiliar with cermet, it is a ceramic–metal composite that prioritises edge sharpness and wear resistance at finishing speeds; this means better part appearance and less need for secondary polishing when compared with coarser grades. Reliable fit and stable mounting for predictable machining Manufactured to ISO dimensions, the insert matches standard holders when form, relief angle, tolerance class, fastening method, size and thickness align. The combination of 80° geometry and a 0° relief angle gives robustness in radial engagement while the cylindrical hole and secure fastening reduce micro-movement during cuts. The double-sided design with double-sided chipbreakers allows indexable use on both faces, extending tool life per cutting edge and simplifying inventory management for production environments. Practical guidance for application and process optimisation Designed primarily for external and internal turning, the indexable plate excels with small depths of cut and continuous feed conditions. Select the appropriate chipbreaker and the NS9530 grade when the priority is surface finish rather than heavy interrupted cuts. For process planners, the benefits are straightforward: consistent chip formation, lower rework rates and predictable tool-change intervals. If finishing stainless or other alloys, verify feed and speed windows for cermet grades to maintain edge life and avoid thermal shock. Contact Metav Werkzeuge for availability, cutting data and tailored advice on the CNGG120408 NS9530 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997786 Manufacturer SKU: TUN6997786 SKU: 6997786-Tungaloy Designation: CNGG120408 Full article name: CNGG120408 NS9530 Tungaloy-Wendeplatte Facts ISO designation: 120408 Insert size: 12 Thickness: 4.76 mm Corner radius: 0.8 mm Geometry angle: 80° Relief angle: 0° Hole style: cylindrical hole Special features Grade: NS9530 (uncoated cermet) Chipbreaker: double-sided Plate shape: rhombic Series: ISO indexable turning inserts Application: Turning (external and internal) Mounting: compatibility determined by form, fastening and tolerance FAQ What materials is this insert suited for? The CNGG120408 NS9530 insert is specified as a finishing grade for steel and delivers low cutting forces and a fine surface finish when used under continuous cutting conditions. Can the insert be indexed and used on both sides? Yes, the insert’s double-sided chipbreaker design allows both faces to be used, extending the number of available cutting edges per plate. Which toolholders are compatible with this ISO plate? Compatibility depends on holder form, free angle, tolerance class, fastening method, size and thickness; the ISO designation 120408 aids selection of matching ISO holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CNGG 120408 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of an economical double-sided design, a TH10 uncoated carbide grade for low cutting forces and clean finishes, and full ISO compatibility for straightforward toolholder matching; order the CNGG120408 TH10 indexable insert directly via Metav Werkzeuge or ask our consultants for application advice. CNGG 120408 TH10 indexable insert for Turning — Tungaloy CNGG120408 TH10 Tungaloy indexable insert offers a robust solution for general turning of non-ferrous materials and applications where a low cutting force and fine surface are priorities ISO‑standard rhombic insert, 80° cutting angle Uncoated carbide TH10 for clean finishes Double-sided geometry for economical use Compatible with holders using cylindrical hole Reliable ISO compatibility for consistent set-up and repeatability The ISO-standard geometry of this insert guarantees predictable seating and repeatable clamping in matching toolholders. With an 80° cutting angle and rhombic form, the insert fits a wide range of external and internal turning operations. The presence of a cylindrical hole and defined tolerance class simplifies assembly and reduces setup time, supporting stable production runs and minimising downtime. This consistency is particularly valuable for batch work where tool change predictability matters. Low cutting forces and improved surface finish for non-ferrous work The TH10 grade is an uncoated carbide formulation optimised for non-ferrous materials and situations that benefit from a sharp, uncoated cutting edge. The sharp edge geometry reduces built-up edge and cutting forces, which often results in a better surface finish and less thermal loading on the workpiece. For components demanding clean surfaces and tight tolerances, this combination of grade and geometry delivers tangible process benefits while maintaining straightforward machining parameters. Cost-effective productivity through double-sided use and compact geometry Being double-sided, each insert provides two usable cutting edges, enhancing cost-efficiency without sacrificing stability. The compact 12 mm size and 4.76 mm plate thickness balance rigidity and access in constrained tool setups. A corner radius of 0.8 mm supports edge strength while remaining small enough for fine profiling. Together, these design choices extend economic tool life and reduce tooling cost per component in everyday turning tasks. Integration advice: choosing holders and optimising cutting data Successful performance depends on matching the insert to the correct holder and cutting data. Select a holder that accommodates the rhombic shape, 80° approach, and the 0° relief specification for correct chip flow and contact. Where finish is critical, favour lighter feeds and higher spindle speeds suitable for the TH10 uncoated edge; for roughing, increase the depth of cut but monitor cutting forces. Practical trials on representative stock material are recommended to validate parameters and confirm expected results with the Tungaloy grade. Practical benefits for production workflows Incorporating this indexable insert into production supports rapid tool replacement, reliable repeatability and reduced inventory complexity thanks to ISO conformity. The simple, uncoated cutting edge removes concerns about coating delamination in some non-ferrous applications and eases regrinding or inspection routines. Overall, this insert helps maintain machining stability while contributing to consistent part quality and predictable cycle times. For application-specific recommendations or to secure the Tungaloy CNGG120408 TH10 insert for upcoming jobs, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance and ordering. Technical data Article number: 6801881 Manufacturer SKU: TUN6801881 SKU: 6801881-Tungaloy Model series: ISO turning indexable inserts Product designation: CNGG120408 TH10 Key dimensions Insert size: 12 mm Plate thickness: 4.76 mm Corner radius: 0.8 mm Relief angle: 0° Cutting angle: 80° Features Shape: rhombic Hole: with cylindrical hole Edges: double-sided Grade/coating: TH10, uncoated carbide Material: carbide Application: Turning (external and internal) FAQ What materials is this insert best suited for? The CNGG120408 TH10 Tungaloy indexable insert is optimised for non-ferrous materials and applications where an uncoated, sharp carbide edge reduces cutting forces and improves surface finish. Is the insert compatible with standard ISO toolholders? Yes, the insert follows ISO geometry conventions; compatibility depends on matching form, relief angle, tolerance class, fastening and plate thickness. How many usable edges does each insert provide? Each double-sided insert offers two usable cutting edges, increasing economical performance for repetitive turning tasks. What is the corner radius and how does it affect machining? The corner radius is 0.8 mm, balancing edge strength with the capability to produce relatively fine profiles and good surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com