Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
162mm Vertical Clamp With Massive Holding Arm, 1,200N Press Force, Galvanised - Kukamet
Take advantage of the combination of compact dimensions, reliable clamping force and a zinc-plated corrosion-resistant finish for consistent fixture performance. Order the vertical clamp directly via Metav Werkzeuge or consult our specialists for application advice. Vertical clamp 212 — Kukamet vertical clamping lever, 162 mm arm, zinc-plated The Vertical clamp 212 is a compact vertical clamping lever designed for fixture and workshop use where firm, repeatable clamping is required and mounting space is limited. Robust 162 mm solid holding arm Zinc-plated construction for corrosion resistance Clamping force up to 1,200 N Holding force up to 1,400 N Reliable clamping in compact fixtures The vertical clamp delivers measurable performance where space is constrained. With a slender footprint and a 162 mm arm, the device enables stable clamping without requiring excessive installation area. The compact design supports efficient fixture layouts, reducing cycle times in repetitive operations while keeping access to the workpiece clear. This makes the clamp suitable for production jigs and small-batch assembly stations where precise positioning and repeatability are required. Durable construction for daily workshop use Genuine workshop reliability is achieved through a zinc-plated finish and a solid holding arm, which together protect against corrosion and mechanical wear. The galvanised surface prolongs service life in humid or mildly corrosive environments, while the massive arm resists deformation under load. The result is lower maintenance frequency and predictable performance across production runs, supporting long-term operational stability in both manual and semi-automated setups. Measured force for secure, repeatable fixation Designed to provide clear force specifications, the clamp offers a clamping force of up to 1,200 N and a holding force of up to 1,400 N. Clamping force refers to the operational force applied during engagement, while holding force indicates the static retention once the lever is locked. These values help in component selection and risk assessment when securing parts made from common workshop materials, allowing planners to size fixtures according to known mechanical requirements rather than approximation. Straightforward integration into existing fixtures Mounting is via a vertical foot that simplifies attachment to plates, benches or modular tooling. At just 0.256 kg, the unit adds minimal mass to assemblies while offering robust performance, making it suitable for transportable jigs and indexing fixtures. The model’s clear mechanical function — a lever-actuated toggle that locks securely — enables quick installation and predictable behaviour within production sequences, reducing setup times and facilitating rapid changeovers. For procurement or technical advice on the Kukamet vertical clamp 212 and compatible fixture solutions, contact Metav Werkzeuge for tailored recommendations at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: 212-2-D-C3 GTIN: 8680731501537 Manufacturer: Kukamet Facts Arm length: 162 mm Clamping force (max): 1,200 N Holding force (max): 1,400 N Weight: 0.256 kg ECLASS: 21041717 ETIM: EC011973 Special features Material: zinc-plated Mounting: vertical foot Massive holding arm Model: 212 Category: clamp FAQ What type of applications is this clamp suited for? The clamp is designed for fixture work, assembly jigs and workshop tooling where a compact vertical clamping action and reliable retention are required; the Kukamet vertical clamp 212 is particularly useful in production and inspection fixtures. How does the clamping force relate to holding force? Clamping force (up to 1,200 N) describes the operational engagement power, while holding force (up to 1,400 N) indicates the static retention after locking; both values help determine suitability for specific parts and materials. Is the clamp protected against corrosion? Yes, the zinc-plated finish provides corrosion resistance suitable for typical workshop environments and extends service life under normal conditions. Can this clamp be mounted on modular fixturing plates? The vertical foot mounting is compatible with plate and bench installations, enabling easy integration into modular fixturing systems and quick replacement where required. What are the main physical dimensions to consider? Key dimensions to note are the 162 mm arm length and the compact footprint provided by the vertical foot, which together influence reach and clearance in fixture design. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
162mm Vertical Clamp With Massive Holding Arm, 1.2kN Press Force, 1.4kN Holding Force - Kukamet
Take advantage of a compact 162 mm arm, 1,400 N holding force and a solid holding arm to secure workpieces reliably in vertical setups; order the clamp directly via Metav Werkzeuge or consult our specialists for tailored fixture recommendations. 212 Vertical Lever Clamp — Kukamet · 162 mm arm · 1,400 N holding force The 212 vertical clamp is a compact vertical lever clamp for workshop and industrial fixtures, engineered to provide secure perpendicular clamping where space is limited and repeatable positioning is required. Solid holding arm for reliable clamping 162 mm arm for extended reach 1,400 N maximum holding force Blackened finish for corrosion resistance Stable, high-force clamping for repeatable setups The vertical lever design delivers a dependable holding force of 1,400 N, ensuring consistent fixation for medium-duty assembly and jigs. The combination of a rigid lever mechanism and a solid holding arm reduces movement under load, which supports repeatable positioning and shortens setup time in production processes. The 1,200 N rated pressing capacity complements the holding performance, allowing secure engagement without the need for bulky fixtures. Space-saving mounting that adapts to workshop rigs A 162 mm arm provides additional reach while maintaining a compact footprint suitable for tight fixture grids and conveyor-mounted stations. The vertical base allows the clamp to be mounted with its foot in a perpendicular orientation, making it straightforward to integrate into existing clamping plates or bespoke tooling blocks. This arrangement improves accessibility to the workpiece and helps maintain clear tool paths during machining or inspection sequences. Robust finish and lightweight handling for everyday use Finished in a blackened coating, the clamp resists surface wear and offers improved corrosion protection in workshop environments. At approximately 0.256 kg, the unit combines low mass with mechanical resilience, simplifying handling during fixture changes and minimising added load on adjustable fixtures. The lever-style actuation provides quick engagement and disengagement, supporting efficient cycle times without compromising clamping integrity. Contact Metav Werkzeuge for delivery and specification support regarding the Kukamet 212 vertical clamp — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss integration into existing fixtures Technical data SKU: B212-2-D-C3 GTIN: 8682843522288 Manufacturer: Kukamet Facts Arm length: 162 mm Holding force: 1,400 N Pressing force: 1,200 N Weight: 0.256 kg eClass: 21041717 ETIM: EC011973 Special features Solid holding arm Vertical base mounting Blackened finish Lever clamp design Category: Clamps / Spanners FAQ What holding force can be expected from this clamp? The Kukamet 212 vertical clamp provides a holding force of 1,400 N, with a pressing capacity rated at 1,200 N for secure engagement. Can the clamp be mounted on a standard fixture plate? Yes, the vertical base mounting is designed for direct integration into fixture plates and bespoke tooling blocks used in workshop and industrial settings. What is the working reach of the clamp? The clamping arm offers a reach of 162 mm, giving extended access while preserving a compact installation footprint. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
162mm Vertical Clamp With Vertical Foot, 1.2kN Thrust, 1.4kN Holding Force, Blackened Steel - Kukamet
Take advantage of a compact, high‑force clamping solution that combines a robust 162 mm holding arm, up to 1,400 N holding force and a corrosion‑resistant finish for dependable fixture work; order supply and technical advice via Metav Werkzeuge for smooth integration into workshop production. Vertical Clamp 212 (B212-2-D-L-C3) — 162 mm arm, 1,400 N holding force by Kukamet Vertical Clamp 212 is a vertical‑foot workholding device engineered for reliable clamping in light to medium industrial fixtures and jigs. Robust 162 mm holding arm and safety lock Up to 1,400 N holding force Corrosion‑resistant blued finish Lightweight at 0.21 kg for easy mounting Compact design that keeps fixtures precise The Vertical Clamp 212 delivers concentrated holding force in a compact package, making it suitable where space is limited but stability is essential. With a 162 mm arm and 1,400 N maximum holding capacity, the clamp secures small parts reliably during machining and assembly. The ratio of holding power to mass — at just 0.21 kg — reduces additional load on fixtures and enables simpler jigs without sacrificing clamping performance. For purchasers seeking measurable, repeatable results, this balance of size and force supports shorter setup times and fewer reworks. Measurable performance for process reliability Two distinct force parameters define application performance: the holding force of 1,400 N ensures a sustained grip on components, while the maximum pressing force of 1,200 N indicates the device’s capacity during actuation. Explaining these figures helps planners choose the right clamp for specific materials and operations: holding force resists part movement in use, pressing force relates to the actuation effort and contact pressure. This separation of terms supports efficient decision making in toolroom and production planning and reduces the risk of underspecified clamping. Safe operation and long service life Designed with a massive holding arm and integrated safety lock, the unit prevents unexpected release during processing and adds an extra layer of operator safety. The blued (blackened) finish provides corrosion resistance and a reduced surface shine that is beneficial in workshop environments. These design choices lower maintenance needs and extend service intervals, meaning less downtime and a longer effective service life for the clamping hardware. Simple integration into workshop systems Mounting via the vertical foot enables straightforward installation on benches, fixture plates or custom jigs, and the clamp’s modest weight keeps handling and positioning easy. The device matches well with standard fixture workflows in machine shops and assembly cells where consistent, repeatable clamping is required. For buyers who value a trustable supply chain, Metav combines broad availability with expert advice and a European quality filter that supports reliable procurement and predictable replenishment. For technical procurement or application advice on the Kukamet Vertical Clamp 212, contact Metav Werkzeuge to arrange supply and guidance: call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: B212-2-D-L-C3 ECLASS: 21041717 ETIM: EC011973 Facts Arm length: 162 mm Holding force (max): 1,400 N Pressing force (max): 1,200 N Weight: 0.21 kg Special features Attachment type: vertical foot Finish: blackened (blued) Massive holding arm and safety lock Material appearance: blackened/brünierte surface Brand: Kukamet FAQ What clamping capacity does this clamp provide? The Vertical Clamp 212 from Kukamet offers a maximum holding force of 1,400 N and a pressing force up to 1,200 N, suitable for many light to medium workshop fixtures. Is the clamp suitable for corrosion‑prone environments? The clamp features a blackened (blued) finish that increases resistance to corrosion and is suited for typical workshop conditions. How is the clamp mounted to a fixture plate? Mounting is via the vertical foot configuration, allowing direct attachment to benches or fixture plates in jigs and tooling assemblies. What safety features are integrated in the design? The device includes a massive holding arm and an integrated safety lock that prevents unintended release during machining or handling. Which SKU should be referenced when ordering or specifying? Reference SKU B212-2-D-L-C3 when specifying or ordering the Kukamet Vertical Clamp 212. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
162mm Vertical Clamp With Vertical Foot, Heavy Holding Arm, Safety Lock, 1,200N Thrust/1,400N Hold, Zinc-Plated - Kukamet
Combine strong clamping performance with a massive holding arm and a secure safety lock for dependable fixture work; order the Vertical Clamp directly via Metav Werkzeuge or ask our consultants if needed. Vertical Clamp 212 by Kukamet — Massive holding arm & 1,200 N clamping force The Vertical Clamp 212 is a compact vertical clamping device designed for secure workpiece fixation in jigs, fixtures and assembly applications. Massive holding arm with safety lock Zinc-plated for corrosion resistance 1,200 N clamping force, 1,400 N holding force Compact 162 mm arm, lightweight 0.21 kg Consistent clamping force for repeatable results The clamp delivers a defined clamping force of 1,200 N and a holding force of 1,400 N, values that ensure reliable fixation during machining, assembly and inspection tasks. These figures describe the actionable pressure applied during the clamping action and the maximum load the latch will retain; translated into shop-floor practice, this means repeatable clamping with reduced slippage and fewer rejected parts. The lever-driven mechanism converts manual input into stable force, enabling predictable setup times and consistent process outcomes across batches. Robust construction for daily workshop use Constructed from zinc-plated steel with a massive holding arm, the device is built to resist wear and corrosion in demanding environments. The vertical mounting foot provides a secure attachment point for machine tables and fixture plates; the 162 mm arm gives an effective reach while keeping the overall footprint compact. At 0.21 kg, the clamp is lightweight enough for quick retrofitting yet substantial where rigidity matters. The integrated safety lock prevents accidental release, improving operator safety and reducing the risk of workpiece damage during handling or vibration-prone operations. Practical integration into jigs and production fixtures The clamp’s vertical orientation and lever action make it suitable for horizontal and vertical fixtures where overhead clearance is limited. The compact design supports simple retrofit into modular fixturing systems or custom jigs without extensive modification. Because the mechanism is manual and mechanically straightforward, maintenance requirements are minimal: periodic inspection and lubrication keep the clamp performing reliably. For production environments seeking predictable manual clamping with low complexity, this clamp provides a pragmatic balance of force, durability and ease of use. Contact Metav Werkzeuge for application advice, to request a quote for the Kukamet Vertical Clamp 212 or to discuss fixture integration by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: 212-2-D-L-C3 GTIN: 8680731501568 Eclass: 21041717 ETIM: EC011973 Facts Clamping force max: 1,200 N Holding force max: 1,400 N Arm length: 162 mm Weight: 0.21 kg Special features Material: zinc-plated Mounting: vertical foot Massive holding arm Safety lock FAQ What clamping and holding forces does the clamp provide? The clamp offers a clamping force of 1,200 N and a holding force of 1,400 N, values suitable for secure manual fixation in fixtures where repeatable pressure is required. Can the clamp be mounted on standard fixture plates? Yes. The vertical foot design allows the clamp to be fixed to machine tables or fixture plates for straightforward integration into jigs and assemblies. Is the surface protected against corrosion? The clamp is zinc-plated, providing corrosion resistance appropriate for workshop and industrial environments. Does the clamp include a safety mechanism to prevent accidental release? A dedicated safety lock is integrated to secure the lever in the closed position and reduce the risk of unintended opening under load. What is the effective reach of the clamp arm? The device features a 162 mm arm, offering a balance between reach and compact installation space. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
164mm Centre Tip Live Centre, 0.005mm Accuracy, Alloy Steel, 2000 rpm - Vertex
Take advantage of 0.005 mm concentricity together with a robust alloy steel construction and a compact 164 mm length for reliable turning support; order the VPC‑MT3 directly via Metav Werkzeuge or ask our consultants for tailored advice. VPC‑MT3 Universal live centre — 0.005 mm runout, 2000 r.p.m., Vertex A VPC‑MT3 Universal live centre for rotating workpiece support in lathe turning, designed to maintain concentricity and reduce deflection during machining. High precision: 0.005 mm runout Designed for speeds up to 2000 r.p.m. Alloy steel body for durability 164 mm overall length for deep support Maintain concentric turning with measurable accuracy The VPC‑MT3 delivers exceptionally low runout of 0.005 mm, a specification that directly improves repeatability and surface finish in turning operations. Low runout means the centre point runs closer to the true axis, reducing radial vibration and minimising rework. For workshops aiming to keep tolerances tight, this level of precision supports repeatable part quality and consistent inspection results. Reliable rotation at practical lathe speeds Designed for rotation at up to 2000 r.p.m., this revolving centre suits a wide range of medium‑speed turning tasks. The controlled rotational capability ensures stable support of the workpiece, which in turn maintains machining tolerances and reduces tool wear. With an overall length of 164 mm and a compact mass of 0.9 kg, the unit provides deep support where longer reach is required while remaining easy to handle during setup. Durable construction for everyday workshop use Constructed from alloy steel, the live centre is built for longevity under routine workshop conditions. The material choice balances toughness with dimensional stability, keeping the centre point concentric over many cycles. As a universal support device, the centre is suited for general turning applications where robust, repeatable support is required rather than specialised or medical precision use. For precision turning tasks where concentricity and dependable rotation matter, choose the Vertex VPC‑MT3 — contact Metav Werkzeuge in Emmerich for product availability and application guidance via info@metav-werkzeuge.com or by phone. Technical Data Article number: VPC-MT3 GTIN: 4061905085567 Manufacturer: Vertex Facts Runout accuracy: 0.005 mm Maximum speed: 2000 r.p.m. Length: 164 mm Weight: 0.9 kg Special features Material: alloy steel Type: revolving / live centre Brand: Vertex FAQ What degree of concentricity can be expected from this live centre? The VPC‑MT3 achieves a runout accuracy of 0.005 mm, which supports high concentricity in standard turning operations. Is the VPC‑MT3 suitable for medium‑speed lathes? Yes, the unit is specified for operation up to 2000 r.p.m., making it appropriate for many medium‑speed lathe applications. What materials is the centre made from and why does that matter? The body is made from alloy steel, chosen for its toughness and dimensional stability, which helps preserve alignment and service life under workshop use. How does the length of 164 mm affect its application? An overall length of 164 mm provides extended reach for deeper support into the spindle or over long workpieces while keeping handling straightforward. Which SKU should be ordered for this universal live centre? Order the VPC‑MT3 (SKU: VPC-MT3) for the universal live centre in Vertex’s range Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
164mm Morse Taper MT4 Tapered Arbor Hardened And Ground With Drill Chuck Taper DIN 238 - TECWERK
Take advantage of the hardened and ground construction together with a DIN 238 drill‑chuck taper for reliable chuck retention and long service life; the compact MT4 to B18 taper interface ensures straightforward integration into existing machine spindles. Order directly via Metav Werkzeuge or contact our advisors for compatibility guidance. Morse taper mandrel MT4 → B18 — hardened and ground, DIN 238 drill‑chuck taper (TECWERK) The Morse taper mandrel MT4 to B18 forms a precision interface for mounting drill chucks on drilling and turning machines, combining standardised taper geometry with a hardened, ground finish for consistent performance Morse taper MT4 shank DIN 238 drill‑chuck taper Hardened and ground finish 164 mm overall length Secure chuck mounting that keeps tools concentric The tapered interface delivers a precise mechanical fit, reducing run‑out and improving hole quality when using a mounted chuck. Fitted to a standard MT4 shank and finished to the DIN 238 drill‑chuck taper, this mandrel provides a repeatable connection between spindle and accessory. The result is consistent concentricity, which directly affects drilling accuracy and tool life; the hardened and ground surface minimises wear on both the mandrel and the mounted chuck, preserving alignment over many cycles. Robust construction for continuous workshop use Manufactured with a hardened and ground execution, the mandrel resists deformation and surface fatigue under regular load. The tough finish lowers the risk of fretting and galling where taper meets taper, extending the service interval of both accessory and spindle. For production environments and maintenance shops alike, that durability translates into predictable uptime and fewer interruptions for re‑alignment or replacement, supporting a smoother workflow on machining centres and bench machines. Clear compatibility and easy integration Engineered to accept drill chucks via the DIN 238 taper and to seat in an MT4 spindle, the component simplifies tool changeovers in mixed‑equipment shops. The male B18 fitting matches common spindle sockets, and the 164 mm overall length provides sufficient engagement without excessive overhang. For users unfamiliar with taper nomenclature: MT4 refers to Morse taper size 4, a widely adopted standard; DIN 238 specifies the drill‑chuck arbor form used to secure chucks by taper seating. This clarity helps reduce selection errors and ensures the mandrel integrates with existing tooling. Practical benefits for purchasing and workshop management Choosing a hardened taper mandrel reduces the need for frequent replacements and supports predictable process outcomes—an economic advantage over time for high‑volume or precision work. The standardised interfaces mean spare parts and mounted chucks remain interchangeable across machines, simplifying stockkeeping and reducing the variety of components in the toolroom. Where installation or fitment questions arise, Metav Werkzeuge’s product information and technical team can advise on compatibility and best practice for mounting and maintenance. For reliable chuck retention and long service life, order the TECWERK MT4→B18 taper mandrel via Metav Werkzeuge or contact Metav Werkzeuge’s advisors at info@metav-werkzeuge.com / +49 2822 7131930 to confirm fitment and application suitability Technical data SKU: 2000832348NW Standard: DIN 238 Brand: TECWERK Product type: Taper mandrel Facts Overall length: 164 mm Packaging unit: 1 Special features Morse taper: MT4 Spindle fitting: B18 Drill‑chuck taper: DIN 238 Execution: hardened and ground Application: for mounting drill chucks on drilling and turning machines FAQ What spindles is the mandrel compatible with? The mandrel is designed to seat in an MT4 taper and to accept a drill chuck via the DIN 238 drill‑chuck taper; compatibility should be checked against the machine spindle and chuck arbor dimensions. Is the mandrel suitable for heavy production use? Yes, the hardened and ground execution provides enhanced wear resistance, making the mandrel suitable for regular workshop and light production environments. How does DIN 238 affect chuck selection? DIN 238 defines the taper form for drill chucks; selecting a chuck with a matching DIN 238 arbor ensures a secure, concentric fit when mounted on the mandrel. Can the mandrel reduce run‑out compared with non‑taper adapters? A precision tapered seat such as MT4, when properly fitted, offers improved concentricity and repeatability compared with loose or improvised adapters, resulting in lower run‑out. Which SKU identifies this item for ordering? This item is listed under SKU 2000832348NW and is the TECWERK taper mandrel MT4→B18 designed for DIN 238 drill‑chuck seating. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
1650 N Clamping Force Horizontal Base Toggle Clamp With Hook, Zinc Plated - Kukamet
Take advantage of the combination of robust galvanised corrosion protection, a compact horizontal mounting base, and proven clamping and holding forces for reliable fixture performance; order the locking clamp directly via Metav Werkzeuge or consult the Metav team for specification advice. Locking clamp 362 — horizontal-base toggle clamp, galvanised (Kukamet) A Locking clamp 362 designed for secure, repeatable clamping on jigs and fixtures, featuring a horizontal foot for stable mounting and an integrated hook for versatile applications. Galvanised corrosion protection Horizontal mounting base Clamping force 1,400 N Integrated hook, 25 mm thread length Proven clamping performance for production use The Locking clamp 362 delivers consistent results through a defined clamping force of 1,400 N and a higher holding force of 1,650 N, values that translate directly into secure workholding under dynamic load. These numerical ratings indicate the clamp’s capacity to resist displacement during machining or assembly; in practice this means fewer re-checks and improved cycle consistency. The galvanised finish contributes to long-term dimensional reliability by limiting corrosion on critical surfaces, while the compact mass of 0.14 kg keeps moving parts light and responsive. Space-saving design that speeds up set-up A horizontal-foot mounting arrangement enables easy installation on jigs, fixtures and assembly tables, where a low profile is essential. The integrated hook together with a 25 mm thread length provides adjustment range for variable material thicknesses without changing attachments, reducing downtime between jobs. The clamp’s lever action is optimised for rapid engagement and repeatability, supporting efficient batch processing and reducing manual repositioning. These characteristics make the component suitable for small-batch work as well as integration into automated production fixtures. Built for durability and dependable supply Constructed from galvanised steel and presented as a lever-style clamp, the device is intended to withstand everyday workshop stresses with minimal upkeep; periodic inspection and light lubrication of the pivot points are sufficient for prolonged service life. Supplied by Kukamet and distributed via Metav Werkzeuge, the part benefits from established logistics and quality oversight at the Emmerich location, offering reliable availability for workshops and production lines. For applications that demand consistent clamping and uncomplicated installation, this clamp provides a pragmatic balance of robustness and simplicity. Choose the Kukamet locking clamp 362 through Metav Werkzeuge for dependable clamping in jigs and fixtures — contact Metav Werkzeuge for tailored advice or detailed specifications at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 362-1 GTIN: 8680731505160 ECLASS: 21041718 ETIM: EC011973 Material: galvanised Core technical data Weight: 0.14 kg Clamping force: 1,400 N Holding force: 1,650 N Thread length: 25 mm Special features Horizontal foot mounting With hook Lever-style clamp (hebelspanner) Category: Spanner SKU: 362-1 Manufacturer: Kukamet FAQ What clamping force can be expected from this clamp? The clamp provides a clamping force of 1,400 N and a holding force of 1,650 N, suitable for secure workholding in many fixture and assembly applications. Is the clamp suitable for repeated industrial use? Yes, the galvanised finish and lever design make the clamp suitable for repeated cycles; light maintenance of pivot points is recommended to preserve performance. How is the clamp mounted and adjusted? Mounting is via a horizontal foot; adjustment is achieved using the integrated hook and the 25 mm thread for compensating material thickness. Which materials is the clamp compatible with? The clamp serves as a mechanical workholding device and can be used with fixtures that secure a wide range of materials; selection should match the required clamping pressure and fixture design. What are the dimensions and weight? The unit weighs 0.14 kg and features a 25 mm thread length; further dimensional details are available on request via Metav Werkzeuge. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
165mm 60° Carbide Centre Punch Fixed Tip, DIN 806 - Vertex
Take advantage of the combination of carbide tip longevity, a 60° centre angle for standardised marking and a robust 165 mm length for controlled reach — all contributing to smoother production and less rework. Order the part directly via Metav Werkzeuge or consult our specialists for application advice. VLC-114 centre punch tip — fixed carbide marking point, 60° (Vertex) The VLC-114 centre punch tip is a fixed, carbide-tipped marking point designed for precise centre punching and layout work in workshop and production environments, conforming to DIN 806. Fixed carbide tip for long-lasting precision 60° centre angle for standard marking Length 165 mm for controlled reach DIN 806 compliant manufacturing quality Reliable marking that reduces rework and downtime A hard-wearing carbide tip delivers consistently sharp impressions over long production runs, which improves precision and reduces the need for repeat marking. The standard 60° centre angle ensures marks are compatible with common tooling and centre drills, enabling predictable alignment during drilling and machining operations. With a robust design, the tool supports steady contact force and repeatable results, contributing to faster cycle times and fewer corrections in downstream processes. Stable design to streamline workshop routines The fixed design of the tip eliminates play between components, giving stable contact and a uniform mark every time; this supports consistent part set‑up and inspection. Compliance with DIN 806 provides a recognised performance baseline, simplifying integration into existing toolsets and quality procedures. A length of 165 mm offers a good balance between reach and control, allowing safer handling when marking assemblies or parts positioned within fixtures without sacrificing operator accuracy. Material advantages explained for confident selection Carbide as a tip material offers superior wear resistance compared with conventional steel points, preserving geometry under repeated impact and abrasive conditions; this equates to extended service life and lower lifetime costs per mark. The compact, robust construction and the tip material together deliver high durability and stable imprint geometry, which supports reliable inspection and repeatability across batches. For production environments that prioritise uptime and predictable tool behaviour, this configuration provides an economical and technically sound solution. Metav as a dependable procurement partner As a precision partner, Metav combines decades of expertise with a broad catalogue to simplify procurement: a single source for measurement and workshop supplies reduces supplier complexity while ensuring product consistency. With a large European stock and established logistics from Emmerich, Metav offers transparent order handling and steady supply — factors that matter for uninterrupted production planning and dependable workshop inventories. Contact Metav Werkzeuge for application guidance on the VLC-114 centre punch tip and secure a reliable marking solution tailored to workshop requirements; Metav’s consultants in Emmerich assist with technical details and delivery arrangements. Technical Data Article number: VLC-114 GTIN: 4061905088216 Material: Carbide tip Standard: DIN 806 Data Length: 165 mm Tip angle: 60° Weight: 0.8 kg Special features Fixed tip design Manufacturer: Vertex SKU: VLC-114 FAQ What is the main benefit of a carbide-tipped centre punch? A carbide-tipped centre punch provides higher wear resistance and longer service life than standard steel points, resulting in more consistent marking and fewer tool changes for the VLC-114 centre punch tip (Vertex, SKU VLC-114). Is the tool suitable for standard drilling preparation? Yes, the 60° tip geometry produces standardised centre marks that are suitable for subsequent drilling and centre-drilling operations, helping to maintain repeatable alignment. Does the product conform to industry standards? The tool is manufactured in accordance with DIN 806, offering a recognised specification for form and function in marking applications. Is the tip replaceable or permanently fixed? The part is specified as a fixed tip design; replaceability is not listed in the standard specification for this item. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
165mm Hydraulic Chuck 3,300 kgf Clamping Force, 0.03mm Accuracy, 2,000 rpm - Vertex
Take advantage of the combination of high clamping force and precise runout control to keep turning and milling operations stable and predictable; the robust 165 mm diameter body and balanced design support safe, continuous use in medium-speed applications. Order the chuck directly via Metav Werkzeuge or contact our consultants for application-specific advice. VSK-6 precision chuck — 165 mm, 3,300 kgf clamping force (Vertex) VSK-6 is a precision clamping chuck designed for secure holding of larger workpieces in lathe and turning centres, suitable for medium-speed machining where stable grip and reproducible positioning are required High 3,300 kgf clamping force 165 mm diameter for larger workpieces Runout accuracy 0.03 mm Balanced for 2000 rpm operation Reliable grip to reduce rework and scrap The robust construction delivers a consistently high clamping force that secures parts during machining, reducing slippage and the need for rework. With a reinforced body sized at 165 mm, the chuck provides an extended contact area for irregular or larger components. The combination of firm holding power and stable seating helps maintain repeatable tolerances and lowers the incidence of rejected parts in serial production. Designed for predictable balance and spindle life Balanced operation is achieved for typical workshop speeds up to 2000 rpm, which minimises vibration and contributes to longer spindle bearings life. The balanced design supports smoother surface finishes and more consistent tool wear, translating into fewer machine interventions. For operations where runout affects process capability, the balanced assembly keeps dynamic behaviour predictable under load. Precision that is easy to verify Runout is specified at 0.03 mm, enabling accurate concentricity for turned parts and precise indexing for machining features. This level of accuracy is measurable with standard metrology tools and offers a clear benchmark for quality control. The stated tolerance supports tight production requirements without invoking complex inspection procedures for each setup. Practical handling and workshop integration With a workshop weight of 9.5 kg, the chuck is portable enough for manual fitting yet heavy enough to ensure solidity on the spindle. Its form factor and connection interface suit common lathe configurations, allowing straightforward replacement of existing chucks where compatible. The mass and balance contribute positively to vibration damping during cutting operations. Material handling and application scope Although specific material recommendations are application-dependent, the chuck’s combination of clamping force and diameter makes it appropriate for a wide range of turning tasks on steel, cast components and aluminium assemblies where secure gripping is essential. The mechanical specification supports use in industrial and subcontracting shops that demand repeatable setup performance. Maintenance and longevity considerations The straightforward mechanical design facilitates routine maintenance and inspection, helping to protect the investment over long production runs. Regular checks of runout and jaw seating, combined with correct mounting practice, preserve the chuck’s accuracy and holding capacity, ensuring long-term reliability in daily workshop use. For precision clamping from Vertex, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VSK-6 GTIN: 4061905096327 ECLASS: 21020590 Core specifications Diameter: 165 mm Clamping force: 3300 kgf Max speed: 2000 rpm Accuracy: 0.03 mm Weight: 9.5 kg Features & suitability Product type: chuck Brand: Vertex High clamping force for secure grip Balanced for medium-speed turning FAQ What diameter does the chuck support? The chuck features a body diameter of 165 mm, providing a larger seating area for substantial workpieces. What clamping force is specified for this chuck? The VSK-6 delivers a clamping force of 3300 kgf, suitable for secure holding in demanding turning operations. What is the maximum recommended spindle speed? Rated balancing supports operation up to 2000 rpm, helping to keep vibration and runout under control. How accurate is the concentricity of the chuck? Runout is specified at 0.03 mm, offering a reliable reference for quality-sensitive machining. What is the unit weight for handling and mounting considerations? The chuck weighs 9.5 kg, which balances portability with robust mass for stable machining. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
165mm Simple Tailstock With Three- Or Four-Jaw Chuck, 1° Scale - Vertex
Take advantage of precise indexing and robust workshop construction to streamline machining operations; the combination of 1° division accuracy and a compact 165 mm centre height supports consistent results and simple integration. Order the VSR-10 directly via Metav Werkzeuge or ask our consultants if needed. VSR-10 Dividing head – 1° indexing, 165 mm centre height (Vertex) The VSR-10 is a compact dividing head designed for precision indexing and fixture work on milling machines, supplied with either a three- or four-jaw chuck for versatile clamping and straightforward part rotation. 1° index graduation Three- or four-jaw chuck option Compact 165 mm centre height Solid 43.5 kg construction Precision indexing that improves throughput A workshop-ready dividing head with 1° graduation provides a simple, verifiable way to perform repetitive angular machining tasks with reduced setup time. The device converts manual or driven rotation into accurate, evenly spaced positions, making it suitable for tasks such as gear blank indexing, hole patterns and fixture alignment. The clear indexing indication and robust gearing translate directly into lower rework rates and higher first-pass yields, which supports a leaner production flow and predictable cycle times. Robust build for reliable daily use The machine-style construction and substantial mass of 43.5 kg give the unit stable behaviour during cutting, reducing vibration and improving surface finish compared with lighter fixtures. A robust body and precision bearings maintain alignment under load, which ensures repeatable results across long production runs. For workshops requiring dependable clamping, the three- and four-jaw chuck options permit secure holding of a wide range of part geometries without frequent re-adjustment, so cycle reliability and operator confidence increase. Compact form for easy integration on the shop floor With a 165 mm centre height, the dividing head fits common machine table envelopes while keeping the workpiece near standard cutter centres. The compact footprint aids fixture planning and allows the device to be used in constrained setups or alongside other workholding. The straightforward mechanical design reduces the need for specialised training: routine indexing and basic clamping are quickly learned, which shortens onboarding time for new operators and supports flexible deployment across different jobs. Clear benefits for procurement and operations Selecting a plain, mechanically driven dividing head emphasises serviceability and longevity: fewer electronics and modular components simplify maintenance and spare-part management. The dependable repeatability and simple adjustment mean lower total cost of ownership in environments that favour predictable performance over complex automation. For businesses consolidating suppliers, this solution matches a practical scope of applications while remaining compatible with standard tooling and chucks. Contact Metav Werkzeuge in Emmerich for specification checks, spare parts availability and ordering of the Vertex VSR-10; reach out via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VSR-10 GTIN: 4061905088926 Manufacturer: Vertex Facts Weight: 43.5 kg Centre height: 165 mm Indexing resolution: 1° Special features Simple dividing head with three- or four-jaw chuck Workshop-grade construction for stable clamping Suitable for indexing and fixture tasks on milling machines FAQ What indexing accuracy does the dividing head provide? The VSR-10 dividing head offers a 1° indexing resolution, suitable for common angular layouts and repetitive patterning tasks. Can the unit accept different chucks for varied parts? Yes, the device is supplied with the option of a three- or four-jaw chuck, allowing secure clamping of round and irregular components for flexible machining. Is the dividing head heavy enough to reduce vibration during cutting? With a mass of 43.5 kg, the unit provides a stable platform that helps reduce vibration and improves surface finish compared with lighter fixtures. How does the centre height affect machine setup? The 165 mm centre height aligns the workpiece close to standard cutter centres, simplifying fixture arrangements and aiding integration on most milling tables. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
165mm Three-Point Chuck, 3-Jaw Self-Centring, 3,300 kgf Clamping Force, 2,000 rpm, 0.03mm Accuracy - Vertex
Take advantage of high clamping force and precise runout to improve machining stability and reduce rework; the 165 mm diameter and 3-jaw self-centring design ensure consistent centre-holding for batch production. Order the VSC-6 directly via Metav Werkzeuge or ask the consultants if needed. VSC-6 3-jaw precision chuck — 165 mm, 3,300 kgf clamping force (Vertex) A VSC-6 3-jaw chuck engineered for reliable clamping in workshop and light industrial turning applications, combining strong grip with fine runout control 165 mm nominal diameter 3-jaw self-centring design 3,300 kgf clamping force Runout accuracy 0.03 mm at up to 2,000 rpm Consistent clamping for higher throughput With a rated clamping force of 3,300 kgf and a nominal diameter of 165 mm, this chuck provides the secure hold needed for repetitive turning tasks. The robust grip reduces workpiece movement and vibration, translating into fewer rejects and shorter cycle times. For production environments where part stability directly affects downstream processes, the combination of firm clamping and a compact footprint supports faster cycle planning and predictable outcomes. Precision that lowers rework and inspection time The specified runout accuracy of 0.03 mm explains why this chuck is suitable where concentricity matters. Reduced radial runout minimises machining errors and surface deviations, which in turn decreases the need for re-measurement and corrective passes. The maximum permissible speed of 2,000 rpm balances rotational performance and dynamic stability, allowing for effective finishing and roughing cycles without compromising dimensional control. Practical design for everyday workshop use The self-centring 3-jaw layout simplifies set-up and shortens clamping operations, supporting quick part changeovers on lathes and turning centres. Maintenance routines remain straightforward because the construction focuses on functional robustness rather than unnecessary complexity. Supplied through Metav Werkzeuge’s European distribution, the unit benefits from a quality-filtered supply chain that emphasises reliability and consistent delivery to workshop benches. Contact Metav Werkzeuge for a tailored quotation or technical clarification on the Vertex VSC-6 and secure supply from our Emmerich warehouse for your next production run Technical data Article number: VSC-6 GTIN: 4061905096044 Manufacturer: Vertex Machinery Works Co., Ltd. Facts Diameter: 165 mm Runout accuracy: 0.03 mm Max speed: 2,000 rpm Clamping force: 3,300 kgf ECLASS: 21020590 Special features 3-jaw self-centring chuck Designed for workshop and light industrial turning Balanced for stable operation at specified speed limits FAQ What is the nominal diameter of this chuck? The chuck has a nominal diameter of 165 mm, specified for the Vertex VSC-6 3-jaw chuck. How precise is the runout of the chuck? Runout accuracy is specified as 0.03 mm for the VSC-6, supporting operations that require tight concentricity. What maximum speed can be used with this chuck? The VSC-6 is rated for up to 2,000 rpm as indicated in the technical specification. How much clamping force does the chuck provide? The chuck delivers a clamping force of 3,300 kgf, giving a secure grip for a range of turning tasks. Is this chuck suitable for quick changeovers in batch production? The self-centring 3-jaw design of the VSC-6 supports efficient set-up and shorter clamping cycles for batch workflows. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
167mm Extension Lever For Clamp, 13.5mm Width, 5mm Thickness - Kukamet
Take advantage of a robust metal construction combined with a compact form factor — the extension lever delivers dependable mechanical advantage while remaining lightweight for easy handling; order the extension lever directly via Metav Werkzeuge or consult our specialists for application guidance. Extension lever »220« – extension handle for toggle clamps, metal, 167 mm The Extension lever »220« provides a durable handle extension for toggle clamps and similar clamping equipment, designed to increase leverage and improve operator ergonomics in assembly and workshop applications. Solid metal construction for long service life 167 mm overall height for extended reach Lightweight at approximately 75 g for easy handling Compatible with standard toggle clamp fittings Greater leverage with a compact, durable design The metal construction of this extension handle offers a reliable upgrade to existing clamping setups, providing increased torque transmission without significant added mass. With an overall height of 167 mm and a nominal weight of 75 g, the component enhances operator leverage while keeping the dynamic load on the clamp low. This makes it suitable for repeated manual operations in production or repair environments, where small improvements in handling speed and fatigue reduction translate to measurable workflow gains. Simplified integration and clear identification Designed for straightforward interchangeability with common toggle clamp fittings, the part is easy to identify and track thanks to the SKU 220-2-06-C1 and the associated GTIN 4061905079498. The compact cross-section — width 13.5 mm and thickness 5 mm — enables fitting in confined jigs and fixtures, allowing retrofitting without major fixture redesign. The concise geometry also aids in predictable force transmission, which supports process stability and repeatable clamping performance. Practical benefits for workshop and production use Beyond raw durability, the extension handle contributes to ergonomic improvements and reduced cycle times by enabling faster, more comfortable actuation of toggle clamps. The lightweight, metal build minimises additional inertial effects, helping to preserve clamp life and avoid unintended stress on pivot points. In workshops where many manual clamping cycles occur daily, this small component can support consistent quality and operator well‑being. Choose the Kukamet extension lever for tried-and-tested robustness — contact Metav Werkzeuge for procurement details or bespoke advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: 220-2-06-C1 GTIN: 4061905079498 Brand: Kukamet Measurements Height: 167 mm Width: 13.5 mm Thickness: 5 mm Weight: 0.075 kg Features Material: Metal Category: Spanner / toggle clamp extension Application hint: lever extension for clamping systems FAQ What is the primary use of this extension lever? The extension lever is used to extend the handle of toggle clamps and similar clamping devices to improve leverage and ergonomics during manual clamping operations. Is the lever compatible with standard toggle clamps? Compatibility with standard toggle clamp fittings is intended; the Extension lever »220« is dimensioned for easy integration in typical jigs and fixtures. What material is the extension handle made from? The extension handle is manufactured from metal, chosen for durability and reliable force transmission in workshop conditions. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
167mm Self-Centring 6-Jaw Chuck, 1200 rpm - Vertex
Take advantage of precise, repeatable clamping thanks to the combination of a self-centring 6-jaw design and a compact Ø 167 mm diameter, ensuring stable turning at up to 1,200 r.p.m. Order directly via Metav Werkzeuge or consult our specialists for tailored delivery and fitment advice. VAS-6 – 6‑jaw self‑centring chuck, Ø 167 mm, Vertex The VAS-6 is a 6‑jaw self‑centring chuck for lathe workholding, engineered to provide consistent clamping and fast set-up for production and workshop applications 6-jaw self-centring design Diameter 167 mm for medium workpieces Max speed 1,200 r.p.m. for efficient turning Robust construction, 9.2 kg mass Repeatable centring for consistent part quality The 6-jaw layout delivers uniform gripping force around the workpiece, reducing runout and improving repeatability across batch production. The self-centring mechanism shortens setup times compared with independent-jaw systems, which supports higher throughput without sacrificing accuracy. For operations where concentricity and surface finish are critical, the chuck’s geometry helps maintain steady cutting conditions and predictable results. Balanced mass and speed for stable machining A mass of 9.2 kg combined with a rated maximum of 1,200 r.p.m. provides a stable rotating assembly that resists chatter in medium‑duty turning. The Ø 167 mm jaw span suits a wide range of round and slightly irregular components often encountered in maintenance, prototyping and small-series manufacture. Clear specification of rotational speed supports process planning and helps avoid exceeding safe operational limits during roughing and finishing passes. Practical integration and workshop efficiency Designed for straightforward mounting in standard lathe setups, the chuck simplifies workholding choices and reduces the number of bespoke fixtures required. The robust construction supports frequent clamping cycles in daily workshop use, while the compact footprint preserves access to tooling and measurement points. Combining predictable clamping behaviour with straightforward handling, this chuck supports leaner workflows and reduces non-productive time in the machine cycle. For reliable, production-ready clamping trust Vertex’s VAS-6—contact Metav Werkzeuge in Emmerich for personalised advice and swift supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: VAS-6 GTIN: 4061905086946 Manufacturer: Vertex Numbers / Core Technical Data Diameter: 167 mm Max speed: 1,200 r.p.m. Weight: 9.2 kg Special features 6 jaws Self-centring chuck design eClass: 21020590 FAQ How does the 6-jaw design affect concentricity? The six-jaw layout increases contact points and balances clamping forces, so the VAS-6 achieves improved concentricity and repeatability compared with three-jaw designs for many medium-sized parts. What is the maximum safe rotational speed for this chuck? The chuck is rated to operate at up to 1,200 r.p.m., which should be observed to ensure safe and stable machining conditions when the VAS-6 is mounted. Which workpiece diameters are suitable for this chuck? With a diameter of 167 mm, the chuck is intended for medium workpieces commonly processed in general workshop and light production turning operations. Can the chuck be used for high-precision finishing operations? Yes, the self-centring mechanism and uniform jaw engagement of the VAS-6 support finishing passes where concentricity and surface consistency are required. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
167mm Vertical Clamp 2000N Closing Force, Massive Arm with Safety Lock, Blackened Finish - Kukamet
A compact, high-force clamp designed for secure, repeatable fixture work: robust massive holding arm and safety locking mechanism combine with a 167 mm reach and a low mass of 0.37 kg for easy integration into bench-top jigs. Order the Vertikalspanner directly via Metav Werkzeuge or ask our consultants if needed. Vertikalspanner 212 – Vertical clamp with 167 mm arm, 2,000 N clamping force (Kukamet) The Vertikalspanner 212 is a vertical clamp engineered for secure, repeatable clamping in assembly and workshop fixtures. Massive holding arm with safety lock 167 mm arm for extended reach Vertical-foot mounting for bench installation Up to 2,500 N holding force Reliable clamping performance for consistent production The clamp delivers defined clamping and retention values: a maximum clamping force of 2,000 N and a maximum holding force of 2,500 N. These figures describe the applied downward force during operation and the secure retention once locked. Engineers and technicians benefit from repeatable clamping that reduces setup variability and supports steady cycle times on jigs and fixtures. Clear numerical values enable straightforward integration into force budgets and safety calculations. Built for safe, repetitive operation A massive holding arm and a dedicated safety locking mechanism prioritise operator protection and process reliability. The heavy-duty arm improves resistance to bending under load, while the locking feature prevents accidental release during machining, assembly or transport of a fixed workpiece. The blackened finish provides corrosion resistance and a matt surface that reduces glare and visible wear, supporting a professional workshop standard and long-term service life. Compact design eases retrofit and fixture layout With a reach of 167 mm and a net weight of 0.37 kg, the clamp is compact yet substantial enough for demanding tasks. The vertical-foot mounting simplifies attachment to benches, plates or fixture bases without requiring large clearances, allowing close-packed fixture designs and efficient use of workbench space. The low mass contributes to easier manual handling during jigs assembly and reduces added load on lighter fixtures. Clear suitability and straightforward upkeep The unit suits assembly, holding and clamping tasks in small-batch production and workshop environments where secure retention and quick cycle changes matter. Maintenance is simple: regular inspection of the locking mechanism, light lubrication of pivot points and visual checks on the arm finish preserve reliable operation and prolong service life. Specification-driven design supports engineers in selecting the clamp where defined force and compact mounting are required. For secure, repeatable clamping choose Kukamet’s Vertikalspanner 212—contact Metav Werkzeuge for tailored advice and rapid supply from Emmerich. Technical Data Article number: B212-3-D-L-C3 Manufacturer: Kukamet Category: Clamps Core specifications Arm length: 167 mm Max clamping force: 2,000 N Max holding force: 2,500 N Weight: 0.37 kg Features & finish Mounting: vertical foot Material/finish: blackened finish Massive holding arm Safety locking mechanism FAQ What forces does the clamp provide and what do they mean? The Vertikalspanner 212 specifies a maximum clamping force of 2,000 N (applied force during engagement) and a maximum holding force of 2,500 N (retention once locked), which helps dimension fixtures and safety margins. How is the clamp mounted to a bench or fixture? Mounting is via a vertical foot design, allowing the clamp to be fastened directly to bench tops or fixture plates for compact installation. Is the arm suitable for heavy-duty use and does it resist wear? The product features a massive holding arm and a blackened finish that increases surface durability and reduces visible wear in workshop use. What maintenance is recommended to keep reliable operation? Periodic inspection of the safety locking mechanism, light lubrication of moving joints and visual checks of the arm finish are recommended to maintain performance. Which SKU should be referenced when ordering or specifying this clamp? Reference SKU B212-3-D-L-C3 when ordering or specifying the vertical clamp to ensure correct identification. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
167mm Vertical Clamp 2000N Closing Force, Massive Hold Arm With Safety Lock, Zinc Plated - Kukamet
Take advantage of a galvanised, compact vertical clamp that combines robust holding force and a secure safety lock for reliable fixturing. The unit’s 167 mm arm and rated 2,500 N holding force support stable clamping in demanding workshop setups — order directly via Metav Werkzeuge or ask their consultants for application advice. Vertical clamp 212 by Kukamet — galvanised vertical clamping device, 2,500 N holding force The Vertical clamp 212 is a galvanised vertical clamping device for workshop and fixture applications that provides a heavy-duty holding arm and an integrated safety lock for secure part retention Galvanised construction for corrosion resistance Heavy-duty holding arm with safety lock Up to 2,500 N maximum holding force Compact 167 mm arm for precise positioning Durable construction that prolongs service life The clamp’s galvanised finish delivers reliable corrosion protection, reducing maintenance intervals in humid or light-industrial environments. Built with a massive holding arm, the device maintains consistent clamping pressure during repeated cycles, which lowers the risk of setup slippage and production stoppages. The solid construction also means fewer replacements over time, supporting continuous operation and lower lifetime costs for workshop fixtures. Predictable clamping performance for repeatable results Engineered for stability, the unit provides a maximum holding force of 2,500 N and a pressing capacity of 2,000 N, enabling secure fixation of small to medium workpieces during machining or assembly. The integrated safety lock prevents unintended release under vibration or impact, ensuring that clamping force remains constant once engaged. Such predictable force characteristics simplify process planning and improve part quality by reducing movement during operations. Space-saving design for accurate setups With a 167 mm arm and a compact footprint, this vertical clamp fits into tight fixture layouts where access and repeatability matter. The vertical-foot mounting arrangement allows straightforward installation on plates and tooling blocks, facilitating fast integration into modular fixtures. The relatively low weight (0.37 kg) contributes to nimble handling when configuring jigs and reduces added mass on movable assemblies. Suitable for workshop fixtures and production aids The clamp is designed as a practical fixture component for assembly benches, drill jigs and light machining setups. The combination of galvanised material and a heavy-duty arm with a locking mechanism makes it appropriate for repetitive tasks where consistent part positioning is required. The device supports efficient workflows by offering a straightforward mechanical solution for secure part retention without complex adjustments. For reliable clamping solutions from Kukamet, request the Vertical clamp 212 via Metav Werkzeuge — contact Metav Werkzeuge in Emmerich for application-specific recommendations at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 212-3-D-L-C3 GTIN: 8680731501643 Manufacturer: Kukamet EClass: 21041717 ETIM: EC011973 Facts Arm length: 167 mm Maximum holding force: 2,500 N Maximum pressing force: 2,000 N Weight: 0.37 kg Special features Material: Galvanised Mounting: vertical foot Massive holding arm and safety lock Compact vertical clamp for workshop fixtures FAQ What maximum holding force does the clamp provide? The Kukamet Vertical clamp 212 delivers a maximum holding force of 2,500 N (SKU 212-3-D-L-C3), suitable for secure retention of small to medium workpieces. Is the clamp protected against corrosion? Yes, the fixture is galvanised to provide enhanced corrosion resistance for typical workshop environments. How is the clamp mounted to a fixture plate? The unit is designed for vertical foot mounting, allowing direct attachment to plates or tooling blocks for compact fixture layouts. What arm length is available for positioning? The clamp features a 167 mm arm that enables precise positioning within confined assemblies and jigs. Can the clamp be used in repetitive production processes? The heavy-duty holding arm combined with a safety lock makes the clamp appropriate for repetitive tasks where consistent clamping force and part stability are required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
167mm Vertical Clamp 2000N Closing Force, Massive Hold Arm, Blackened Finish - Kukamet
Benefit from a massive 167 mm holding arm, up to 2,500 N holding force and a robust blackened finish for dependable vertical clamping in production environments. Order the Vertical clamp 212 directly via Metav Werkzeuge or consult their advisers for application-specific configuration. Vertical clamp 212 — Vertical lever clamp with 167 mm arm and 2,500 N holding force (Kukamet) The Vertical clamp 212 is a compact vertical lever clamp designed for secure workpiece retention in fixtures and jigs across workshop and light industrial settings. Massive 167 mm holding arm Up to 2,500 N holding force Vertical foot mounting Blackened burnished finish Secure clamping for repeatable production The clamp delivers high holding performance with a rated 2,500 N holding force and a maximum pressing force of 2,000 N, making it suitable for repetitive securing tasks in production and assembly. The long 167 mm arm increases reach without compromising stability, enabling secure clamping of irregular or taller workpieces. The specified forces are measured under standard conditions; the result is a measurable improvement in fixture reliability and reduced rework rates when integrated into assembly jigs. Compact, durable design that saves setup time Constructed with a massive holding arm and a blackened burnished finish, the device combines low weight with durability—the unit weighs 0.447 kg, allowing straightforward retrofitting to existing fixtures. The vertical foot mounting provides a low-profile attachment point that minimises interference with tool paths and neighbouring clamps. Surface treatment reduces corrosion and wear, extending service intervals and lowering lifetime operating costs compared with untreated equivalents. Straightforward integration in workshops and fixtures The lever mechanism and compact footprint make the clamp easy to incorporate into dedicated jigs or modular tooling systems. The vertical orientation lends itself to applications where clamping force must be applied from above, for example in positioning stations or test fixtures. Specifying this lever clamp in a fixture layout reduces cycle time by enabling faster part placement and consistent repeatable clamping forces, supporting higher throughput without additional operator training. Contact Metav Werkzeuge today to specify the Vertical clamp 212 for the intended application and secure supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and fast delivery Technical data SKU: B212-3-D-C3 GTIN: 8682843522318 Manufacturer: Kukamet Facts Arm length: 167 mm Holding force max: 2,500 N Pressing force max: 2,000 N Weight: 0.447 kg eClass: 21041717 ETIM: EC011973 Special features Vertical foot mounting Massive holding arm Blackened burnished finish Model designation: 212 Trigger type: lever clamp FAQ What is the maximum holding force of this clamp? The clamp provides a maximum holding force of 2,500 N for the Vertical clamp 212 (Kukamet lever clamp, SKU B212-3-D-C3). How is the clamp mounted to a fixture? Mounting is via a vertical foot, designed for secure attachment to fixture plates and jig bases. Is the surface treated to resist corrosion? Yes, the device features a blackened burnished finish that improves wear and corrosion resistance. Can this clamp be used for manual assembly and automated stations? The compact form factor and lever mechanism suit both manual workstations and integration into automated or semi-automated fixtures. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
167mm Vertical Clamp 2000N Closing Force, Massive Holding Arm, Blackened Finish - Kukamet
Take advantage of the combination of a compact 167 mm reach, robust holding performance and a space-saving horizontal foot for reliable clamping; order directly via Metav Werkzeuge or consult the team for configuration advice. Vertikalspanner 211 Vertical clamp with 167 mm arm and horizontal foot (Kukamet) The Vertikalspanner 211 is a vertical clamp designed for secure, repeatable fixing in limited spaces, suited to workshop and light industrial fixturing. Vertical clamp 167 mm arm Horizontal foot for stable mounting Massive holding arm for repeatable use Blackened finish and low weight 0.45 kg Reliable clamping for repeatable setups The unit is a compact vertical clamp engineered to hold components during machining, assembly or testing. With a 167 mm arm the device extends reach while keeping the footprint modest, enabling the fixture of taller or offset workpieces without compromising stability. The combination of measurable clamping performance and a compact form supports predictable setup times and consistent production flow. Strong holding power with precise control Designed for dependable retention, the clamp provides a maximum 2,000 N clamping force and a peak 2,500 N holding capacity, values that ensure secure fixation during dynamic operations. These figures describe the mechanical limits under standard conditions and help in selecting appropriate workpiece sizes and clamping positions. The clear numeric specification simplifies decision-making when planning fixturing strategies. Durable construction for everyday workshop use The component features a blackened finish applied to minimise surface glare and increase resistance to handling wear, while the massive holding arm provides rigidity where repeatability matters most. Despite its robust build, the device remains lightweight at 0.45 kg, making it straightforward to reposition in modular fixtures or to include in portable tooling sets without adding significant mass to the assembly. Fast integration into existing fixtures A horizontal foot mounting offers a straightforward mechanical interface for bench, plate or jig attachment, reducing setup complexity and downtime. The clamp’s compact profile and sturdy arm support shorter cycle times and fewer resets, which is beneficial for batch work and small-series production. When combined with systematic fixturing, the component contributes to measurable productivity improvements. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet Vertikalspanner 211 into existing fixtures; Metav’s consultants can provide technical details and order support from Emmerich. Technical data SKU: B211-3-D-C3 GTIN: 8680731507713 eClass: 21041717 ETIM: EC011973 Facts Arm length: 167 mm Weight: 0.45 kg Max clamping force: 2,000 N Max holding force: 2,500 N Special features Mounting: horizontal foot Finish: blackened Massive holding arm Category: Spanner FAQ What reach does the clamp offer? The Vertikalspanner 211 has a 167 mm arm, providing extended reach for offset or taller workpieces while maintaining a compact mounting footprint. What clamping and holding forces are specified? Specified maximums are 2,000 N clamping force and 2,500 N holding force for the Vertikalspanner 211, values intended for planning safe and effective fixtures. How is the clamp mounted to a fixture? Mounting is via a horizontal foot, which permits stable attachment to benches, plates or modular fixturing systems. Is the finish suitable for workshop environments? The blackened finish offers a hard-wearing surface that reduces glare and shows minimal handling wear, supporting routine workshop use. Which product identifier is used for ordering? Order reference is SKU B211-3-D-C3; the product is listed under the spanner category and carries GTIN 8680731507713. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
168.5mm Vertical Clamp With Angle Base, Massive Holding Arm, 4.5kN Thrust, 5kN Hold – Kukamet
Take advantage of the combination of robust clamping force, a massive holding arm and a compact, zinc-plated finish to secure fixtures reliably in production and workshop environments. Order the clamp directly via Metav Werkzeuge or consult their specialists for system integration and application advice. Kukamet 213 Vertical Clamp — Massive Holding Arm, Zinc-Plated The 213 Vertical Clamp is a compact vertical clamping device designed for sturdy fixture work and reliable part retention in workshop and production jigs. Massive holding arm for robust clamping Zinc-plated corrosion protection Up to 5,000 N holding force Angle-foot mounting for secure installation Built for dependable clamping performance The vertical clamping device delivers precise, repeatable retention through a combination of high holding force and a massive holding arm. With a rated holding force of 5,000 N and a maximum pressing force of 4,500 N, the unit is engineered to secure components during machining, assembly and testing operations. The zinc-plated finish reduces corrosion risk, extending service life in humid production environments. These technical attributes translate into fewer unclamping incidents, less rework and a more predictable production flow. Space-conscious design that fits fixtures without compromise A short 168.5 mm arm and a compact footprint make the clamp suitable for dense fixture layouts where accessibility and clearance are limited. The angle-foot mounting provides a stable base that simplifies attachment to plates or subplates and helps maintain alignment under load. At a weight of 1.734 kg, the device balances solidity with easy handling during fixture assembly, enabling fast setup changes and reduced downtime when jigs need modification. Durable finish and straightforward integration for industrial use Constructed with a zinc-plated body and a reinforced holding arm, the clamp resists wear from repeated cycles and harsh workshop conditions. The straightforward mechanical design allows integration into existing fixturing systems without complex adaptations; the device functions as a reliable vertical clamping element in modular tooling, inspection fixtures and manual assembly stations. The robust mechanical properties lower maintenance intervals and support consistent production quality over long runs. Contact Metav Werkzeuge today for advice on fixture design, compatibility with existing tooling or to request a tailored quotation for the Kukamet 213 vertical clamp — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data Article number (SKU): 213-5-D-C2 GTIN: 8680731502121 Manufacturer: Kukamet Core specifications Arm length: 168.5 mm Weight: 1.734 kg Maximum pressing force: 4,500 N Maximum holding force: 5,000 N Materials & features Zinc-plated material Angle-foot mounting Massive holding arm Category: Spanner ECLASS: 21041717 ETIM: EC011973 FAQ How much holding force does the clamp provide? The Kukamet 213 vertical clamp delivers a maximum holding force of 5,000 N and a pressing capability of 4,500 N, suitable for demanding fixture applications. Can the clamp be mounted on standard fixture plates? Yes, the clamp features angle-foot mounting that enables secure attachment to plates and subplates commonly used in modular tooling systems; the SKU is 213-5-D-C2. Is the surface finish suitable for humid workshop environments? The clamp is zinc-plated, offering corrosion resistance that helps maintain performance and reduces the need for frequent replacement in workshop conditions. What makes this clamp suitable for compact fixtures? A short arm length of 168.5 mm and a compact design allow placement in tight assemblies while the massive holding arm maintains clamping stability. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
168mm Clamping Ring For Soft Jaw Attachments, For 6" Jaw Caliper - Vertex
Combining a 168 mm nominal diameter with compatibility for 6" soft-jaw attachments and a compact mass of 1.5 kg, this clamping ring provides steady holding with minimal handling effort; Order the clamping ring VFR-06 directly via Metav Werkzeuge or ask our consultants if needed Clamping Ring VFR-06 — 168 mm for 6" soft-jaw attachments, Vertex The clamping ring VFR-06 is a compact workholding accessory engineered to secure soft-jaw fixtures, optimising set-ups in workshop and bench-mount applications 168 mm nominal diameter Compatible with 6" soft-jaw attachments Lightweight at 1.5 kg for easy handling Robust retention for repeatable clamping Faster, repeatable workholding for consistent parts The clamping ring is designed to deliver reliable clamping in fixtures that use soft jaws, helping to maintain concentricity and repeatability across short production runs. Its 168 mm nominal diameter fits common jaw layouts, enabling straightforward integration with existing chucks and fixtures. By focusing on secure radial retention rather than bulk, the component reduces micro-movement during machining and finishing, which supports higher first-pass accuracy and fewer adjustments between cycles. The result is a measurable improvement in throughput and part consistency without complex retrofitting. Reduced setup effort and safer handling At just 1.5 kg, the component lowers handling strain during tool changes and jaw swaps, shortening changeover time and improving operator ergonomics. The light mass also simplifies manual positioning and alignment when paired with standard soft-jaw attachments, making quick fixtures practical even on compact benches. Combined with the clamping geometry tailored for soft materials, the solution minimises the risk of workpiece deformation while preserving a secure hold—an advantage when sensitive or finished surfaces require gentle yet firm retention. Seamless integration for workshop workflows Compatibility with 6" soft-jaw attachments ensures the ring can be introduced into familiar workholding systems without extensive modification. Produced under the Vertex name, the unit supports routine maintenance strategies and straightforward inventory control in precision workshops. Where traceability is important, the VFR-06 designation and associated identifiers simplify stock management and reorder procedures. For operations seeking to harmonise fixtures across machines, the ring offers a compact, purpose-built option that balances accessibility, repeatability and workshop efficiency. Discuss application needs with Metav Werkzeuge to confirm fit for soft-jaw systems and to reserve the VFR-06 for immediate dispatch from our Emmerich facility Technical data Article number: VFR-06 GTIN: 4061905086861 Brand: Vertex Core specifications Diameter: 168 mm Weight: 1.5 kg Suitable for: 6" soft-jaw attachments Applications and features For use with soft-jaw attachments Compatible with 6" soft-jaw workholding systems SKU: VFR-06 FAQ Is this clamping ring compatible with standard 6" soft jaws? Yes. The clamping ring VFR-06 is designed for use with 6" soft-jaw attachments and fits standard workholding arrangements that accept that jaw size. What is the nominal diameter of the component? The ring has a nominal diameter of 168 mm, which accommodates a wide range of chuck and fixture layouts commonly used in workshop environments. How much does the clamping ring weigh? The unit weighs 1.5 kg, a balance between robustness and easy handling during jaw changes and set-up operations. For which applications is this component suitable? The product is intended for workholding scenarios that use soft jaws—holding, finishing and light machining where secure retention and minimal surface deformation are required. What identifiers help with ordering and stock control? Order using SKU VFR-06 or GTIN 4061905086861; both identifiers are provided to simplify procurement and inventory tracking. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
168mm Horizontal Clamp Heavy Holding Arm With Safety Lock, 90° Angle - Kukamet
Combine a massive holding arm, 2,500 N holding force and a secure safety lock for dependable clamping in repetitive production tasks; order the clamp via Metav Werkzeuge or consult the technical team for fitment and compatibility. Kukamet horizontal toggle clamp 112 — 168 mm arm, 2,500 N holding force A robust Kukamet horizontal toggle clamp 112 designed for secure, repeatable clamping in assembly, welding and jig fixtures with vertical-foot mounting for stable attachment. Massive holding arm for high durability Built-in safety lock for secure clamping 2,500 N maximum holding force Vertical-foot mounting for stable installation Robust clamping performance for daily production The clamp is engineered to deliver reliable retention under repeated cycles. The combination of a massive holding arm and a 2,500 N maximum holding force provides a high safety margin for many fixture tasks, while the 2,300 N pressing force ensures secure contact pressure for workpieces. In practical terms, this reduces part movement during machining or welding and lowers rework rates. The robust design translates into longer service life and predictable performance in light industrial environments. Quick action and stable installation for accurate tooling Operation follows the well-established toggle-clamp principle: a short lever travel produces a strong clamping action, enabling fast handling in production runs. The 168 mm arm and 90° angle geometry give a consistent clamping path, and the vertical-foot mounting allows the unit to be fixed to plates or fixture bases with minimal play. The result is repeatable positioning and faster cycle times for assembly or jig operations, with straightforward mechanical behaviour that is easy to integrate into existing tooling. Practical finish, maintenance and application scope Surface protection is provided by a blackened (blued) finish, improving wear resistance and offering basic corrosion protection in workshop conditions. At approximately 0.3 kg, the unit is lightweight to handle when fitting but substantial in feel thanks to its construction. This toggle clamp suits fixture and jig clamping in assembly, welding, woodworking and light machining. Basic upkeep consists of occasional lubrication of the pivot points and inspection of the safety lock for correct engagement, ensuring long-term reliability. For robust, repeatable clamping choose the Kukamet 112 horizontal toggle clamp — contact Metav Werkzeuge for technical advice and secure procurement directly from Emmerich. Technical data Article number: B112-3-D-L-C3 ETIM: EC011973 Manufacturer: Kukamet Facts Arm length: 168 mm Maximum holding force: 2,500 N Maximum pressing force: 2,300 N Angle: 90° Weight: 0.3 kg Special features Vertical-foot mounting Massive holding arm Safety lock Blackened (blued) finish Suitable for fixture and jig clamping FAQ What holding force does the clamp provide? The Kukamet horizontal toggle clamp 112 delivers a maximum holding force of 2,500 N, specified for static retention in fixture applications (SKU B112-3-D-L-C3). How is the clamp mounted to a fixture base? Mounting is achieved via the vertical-foot mounting arrangement; the clamp is designed to be fastened securely to plates or fixture bases for minimal play and stable operation. Which surfaces and materials is the clamp suited for? The clamp is intended for general fixture use in assembly, welding and light machining; the blackened (blued) finish offers basic corrosion resistance for workshop environments. What does the safety lock do? The integrated safety lock secures the clamping arm in the closed position, preventing accidental release and improving safety during repeated handling. Is maintenance complicated for this toggle clamp? Maintenance is straightforward: periodic lubrication of pivot points and visual checks of the safety lock and fastening integrity are normally sufficient to maintain performance. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm 4.5kN Pneumatic Push‑Rod Clamp Horizontal Base, Zinc‑Plated 6.65kN Holding Force - Kukamet
Combining a 4,500 N pneumatic clamping stroke with a 6,650 N holding capacity and a galvanised housing, the clamp delivers dependable retention for automated and manual fixtures; the compact 16 mm piston keeps the unit space-efficient while maintaining force. Order the Pneumatic push rod clamp directly via Metav Werkzeuge or consult our advisors for application-specific recommendations. Pneumatic push rod clamp 661 — 4,500 N, galvanised (Kukamet) The Pneumatic push rod clamp 661 is a compact pneumatic clamp designed for horizontal mounting in production and assembly fixtures, offering robust clamping and secure holding for repeatable processes. Pneumatic actuation for fast clamping Max clamping force 4,500 N Holding force up to 6,650 N Galvanised finish for corrosion resistance Consistent clamping force for repeatable processes The pneumatic actuator provides controlled clamping with a reliable force of 4,500 N, supported by a holding capacity of 6,650 N that secures workpieces during machining or assembly. The specified 16 mm piston diameter balances travel and force transmission, enabling short stroke cycles and rapid cycle times in automated setups. By converting compressed air into linear motion, the device ensures stable, measurable results that suit both batch production and precision fixtures. Space-saving design that fits tight fixtures A compact footprint and a horizontal mounting foot make the unit straightforward to integrate into jigs and fixture plates where space is limited. The relatively low mass of 1.816 kg reduces added inertia on moving assemblies and simplifies handling during fixture build-up. The horizontal foot allows mounting close to the workpiece, reducing lever arm effects and improving clamping consistency in confined toolrooms and production cells. Durable finish and straightforward maintenance The body is galvanised, offering corrosion resistance for industrial environments and extending service life where metalworking coolants or ambient humidity are present. The construction reduces routine maintenance needs and supports long service intervals in demanding applications. Documentation such as the linked catalogue page provides installation guidance and dimensional references to speed up retrofitting and spare-part selection for system planners. Integration and ordering details for production planning For system integration the unit is classified and standardised for production procurement; reference the SKU 661-4-Q16 when specifying fixtures to ensure the correct variant is supplied. The combination of consistent pneumatic actuation, measurable force figures and a compact design supports predictable cycle times and quality control routines in both manual workshops and automated production lines. Contact Metav Werkzeuge today for advice on fixture design or to secure a Kukamet Pneumatic push rod clamp 661 for your production setup — our specialists are available to discuss suitability and application details Technical Data SKU: 661-4-Q16 GTIN: 8680731503135 Manufacturer: Kukamet eClass: 21041716 ETIM: EC011973 Catalogue: 661-662-katalogseite.pdf Facts Max clamping force: 4,500 N Max holding force: 6,650 N Piston diameter: 16 mm Weight: 1.816 kg Special features Material: galvanised Mounting: horizontal foot Category: clamp (Spanner) Actuation: pneumatic FAQ What clamping and holding forces does this clamp provide? The Pneumatic push rod clamp 661 from Kukamet provides a clamping force of 4,500 N and a holding capacity of 6,650 N (SKU 661-4-Q16), suitable for securing parts during machining and assembly. Is the clamp suitable for automated production cells? Yes. The pneumatic actuation and compact design of the Kukamet pneumatic push rod clamp 661 make it suitable for integration in automated fixtures and handling systems. How is the clamp mounted in the fixture? The unit is designed for horizontal mounting with a dedicated horizontal foot, allowing close placement to the workpiece and straightforward fixture integration. What material finish does the unit have for workshop environments? The housing is galvanised, providing corrosion resistance and improved durability in typical workshop conditions. Where can the technical documentation be found? Technical and catalogue information is provided in the listed catalogue page (661-662-katalogseite.pdf) and can be referenced alongside SKU 661-4-Q16 for procurement. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm 5C Collet Precision Clamping Collet, 0.02mm Accuracy - Vertex
Take advantage of the combination of high concentricity, compact dimensions and straightforward compatibility for consistent clamping performance. The collet’s 0.02 mm accuracy and 16 mm bore support reliable tool holding and repeatable results; order the collet directly via Metav Werkzeuge or ask our consultants if needed. 5C-16 5C Collet — 16 mm precision clamping from Vertex 5C-16 is a 5C collet designed for secure, repeatable clamping in toolrooms and machining applications where tight concentricity and standard 5C compatibility are required Accuracy 0.02 mm for precise clamping 16 mm bore compatible with 5C tooling 87 mm length for secure tool engagement Consistent precision where it matters The 5C collet is manufactured to deliver consistent accuracy across repeated setups, with a specified 0.02 mm tolerance that reduces runout and helps maintain part quality. This high level of precision minimises rework and supports tighter machining tolerances, making the accessory a rational choice for production runs where repeatability and minimal scrap influence operating costs. Clear numerical specifications allow planners to assess process capability and integrate the collet into existing tooling systems with confidence. Efficient integration into production workflows Designed to the 5C standard, the collet ensures compatibility with common collet chucks and fixtures, enabling fast tool changes and predictable clamping behaviour. Its compact form factor and standard interface reduce downtime during changeover, supporting an efficient workflow and better machine utilisation. The focus on measurable performance—standardised dimensions and repeatable clamping—addresses productivity targets directly and supports smoother process planning for toolroom and shopfloor operations. Practical handling, robust dimensions and dependable results With a bore of 16 mm, an overall length of 87 mm and a mass of 0.21 kg, the component offers a balance of compactness and engagement depth suited to many machining tasks. The weight and length combine to provide stable engagement without excessive overhang, contributing to controlled dynamics during machining. As a Vertex product, the collet benefits from established manufacturing practices and quality controls, providing assurance that components meet the stated specifications and support consistent production quality. For precise clamping needs, rely on Vertex quality via Metav Werkzeuge — contact our team in Emmerich for tailored advice and sourcing of SKU 5C-16. Technical Data SKU: 5C-16 GTIN: 4061905088568 Manufacturer: Vertex Facts Bore diameter: 16 mm Length: 87 mm Weight: 0.21 kg Accuracy: 0.02 mm eCl@ss: 21041712 Special features Designation: Collet (Spannzange) Standard: 5C Precision manufacturing for tool clamping FAQ What clamping diameter does this collet support? The collet supports a 16 mm bore, specified as the nominal clamping diameter for SKU 5C-16. What level of concentricity or tolerance can be expected? The Vertex 5C-16 collet is specified with an accuracy of 0.02 mm, supporting repeatable concentricity in machining setups. Is the collet compatible with standard 5C chucks? Yes, the component follows the 5C standard and is compatible with standard 5C collet chucks and fixtures. What are the physical dimensions and mass? The collet has an overall length of 87 mm and a mass of 0.21 kg, suitable for compact engagement and stable clamping. Which applications is this collet suited for? The 5C-16 is intended for general clamping tasks in toolrooms and machining operations where a 16 mm bore and high repeatability are required. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
16mm Bolts And T-Slot Kit 38 Pieces, Heat-Treated Steel Black Oxide Finish - Vertex
Combine heat-treated steel construction with a black oxide finish and an M14 thread specification for reliable, repeatable clamping in industrial and trade environments; order the kit via Metav Werkzeuge or contact our consultants for technical advice and fast delivery from Emmerich. VCK-1416 Stud and T-slot Kit — 38-piece clamping set, M14 thread, for 16 mm T-slots (Vertex) The VCK-1416 Stud and T-slot Kit is a compact clamping accessory set designed for securing fixtures and workpieces on T-slot tables and machine beds in industrial workshops and toolrooms. Heat-treated steel with black oxide finish M14 thread for high-strength clamping Compatible with 16 mm T-slots (T16) Complete 38-piece clamping kit Reliable clamping for repeatable setups The kit’s heat-treated steel components provide a high yield strength that supports consistent clamping forces and repeatable setups. The black oxide finish offers increased surface hardness and reduced light corrosion without changing critical tolerances, so fixtures remain secure over repeated cycles. The M14 metric thread provides a conventional, high-load fastening interface that is widely supported on clamping hardware, enabling predictable torque transfer and dependable retention for production and maintenance tasks. Complete set to speed fixture changeovers Supplied as a 38-piece assortment, the set contains T-slot hardware that reduces changeover times by combining essential items in one place. The contents include multiple T-nuts, flanges, couplings and clamping screws, all sized for T16 profiles; this means fewer searches for compatible parts and faster assembly of jigs and workholding fixtures. The integrated selection of components supports modular fixturing and quick reconfiguration on milling machines, drilling tables and inspection benches. Designed for precision and secure assembly Threaded connections and load-distributing flanges in the set ensure secure fixation under machining loads, vibration and repeat handling. The M14 thread dimension is a robust choice for medium to heavy-duty clamping applications, while the T-nuts engage directly with the T-slot profile to prevent rotation and lateral movement. These characteristics reduce slippage and improve positional stability of mounted parts, contributing to consistent machining accuracy and safer operations. Durable finish and straightforward maintenance The combination of thermal treatment and a black oxide finish delivers longevity with minimal upkeep. Routine light lubrication and clean storage keep the components operational for extended service life while maintaining functional tolerances. As an experienced precision partner, Metav Werkzeuge supplies this kit from its quality-filtered stock in Emmerich, ensuring that the components meet workshop demands for durability and availability. For robust, ready-to-fit clamping hardware from Vertex, request the VCK-1416 Stud and T-slot Kit through Metav Werkzeuge—our specialists will advise on compatibility and ensure fast supply from Emmerich to the workshop floor (info@metav-werkzeuge.com | +49 2822 7131930) Technical data SKU: VCK-1416 GTIN: 4061905092350 Manufacturer: Vertex Machinery Works Co., Ltd. Core specifications Set composition: 38 pieces Thread: M14 T-slot compatibility: 16 mm Net weight: 5 kg Materials & contents Heat-treated steel, black oxide finish Contents: 6 T-nuts, 4 flanges, 4 couplings, 24 clamping screws Suitable for T-slot tables and machine beds FAQ What is included in the clamping kit? The VCK-1416 Stud and T-slot Kit includes 6 T-nuts, 4 flanges, 4 couplings and 24 clamping screws supplied as a 38-piece set for workshop fixturing. Which T-slot size does the kit support? This clamping set is compatible with 16 mm T-slots (T16), ensuring direct engagement of the T-nuts with standard machine table profiles. What thread size do the bolts use? The kit uses an M14 metric thread, selected for secure medium to heavy-duty clamping applications and reliable torque transmission. What is the material and surface treatment of the components? Components are made from heat-treated steel with a black oxide finish to increase durability and provide light corrosion resistance. Is the VCK-1416 suitable for industrial machining tasks? Yes, the VCK-1416 Stud and T-slot Kit by Vertex is intended for industrial and trade use on T-slot tables and machine beds where robust and repeatable clamping is required. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
16mm Clamping Screw M12 for 12/14mm Collet Chuck, Cylinder Shaft Clamping - TECWERK
Take advantage of the M12 thread, compact L 16 mm length and compatibility with 12/14 mm chucks for consistent, secure clamping in production settings; order direct via Metav Werkzeuge or consult the technical team for application guidance. Clamping screw M12 L16 mm for chuck Ø12/14 mm (TECWERK) — precision clamping fastener for face-type chucks The Clamping screw M12 L16 mm for chuck Ø12/14 mm (TECWERK) is a purpose-built clamping fastener for face-type chucks, intended to secure tools with a cylindrical shank and a lateral drive flat in accordance with DIN 1835-B. M12 thread for secure clamping Compatible with chuck Ø 12/14 mm Length L 16 mm for compact installations Suited to DIN 1835-B tool shanks Secure retention that improves machining reliability The Clamping screw M12 L16 mm for chuck Ø12/14 mm (TECWERK) combines a standard M12 thread with a compact geometry to deliver secure retention of rotating tools. A positive clamping fit reduces micro-movement between tool and chuck, which helps to maintain concentricity and therefore improves machining accuracy. For production environments where repeatability matters, this specification supports stable cutting conditions and reduced scrap rates. Compact form factor for tight setups and retrofits With a nominal length of L 16 mm, the fastener is designed for installations where projection and clearance are limited. The short overall length minimises overhang, which contributes to better dynamic behaviour during machining and easier balancing of assemblies. This compact design is beneficial for retrofitting existing spindle or chuck configurations where space is at a premium, enabling reliable clamping without extensive rework. Conforms to established tool shank standards for torque transfer Compatibility with tools that feature a cylindrical shank and a lateral drive flat to DIN 1835-B ensures secure torque transmission under load. The lateral flat engages with the chuck mechanism, preventing slippage and supporting repeatable tool indexing. Specifying components that match recognised standards simplifies procurement and guarantees interchangeability across common collet and chuck systems. Ready for straightforward integration and reliable supply Supplied as single units, the clamping screw suits focused replacement needs and small-batch maintenance tasks. The compact specification and standard thread make the component straightforward to add to existing spare-part inventories and facilitates predictable stock management. For workshops and production facilities seeking consistent availability, sourcing via an established distributor helps to ensure continuity of supply and documented product traceability. Contact Metav Werkzeuge for tailored advice on integrating the TECWERK clamping screw M12 L16 mm (SKU 2000834137NW); eMail info@metav-werkzeuge.com or call +49 2822 7131930 for rapid technical guidance and order support Technical data Article number: 2000834137NW Product: Clamping screw Label: Clamping screw M12 L16 mm for chuck Ø12/14 mm TECWERK Brand: TECWERK Facts Thread nominal Ø: M12 Length: 16 mm Suitable for chuck Ø D: 12/14 mm Package unit: 1 Special features For face-type chucks For clamping tools with cylindrical shank with lateral drive flat Conforms to DIN 1835-B FAQ Is this clamping screw compatible with standard 12/14 mm chucks? Yes. The component is specified for use with chucks of Ø 12/14 mm and is intended for face-type chuck assemblies as noted in the technical data (SKU 2000834137NW). Can the clamping screw be used with tools to DIN 1835-B? Yes. It is designed to clamp tools that have a cylindrical shank with a lateral drive flat according to DIN 1835-B, ensuring correct engagement and torque transfer. What are the thread size and overall length of the fastener? The fastener features an M12 thread and an overall length of 16 mm, providing a compact solution for standard clamping applications. How is the item supplied for maintenance and replacement? The product is supplied as single units (package unit 1), which suits selective replacement of worn or lost clamping screws. Is the clamping screw intended for heavy-duty machining tasks? The fastener is designed for reliable clamping in standard machining operations where compatibility with DIN 1835-B shanks is required; for high‑demand or specialised applications, component selection should align with the specific machine and process parameters. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com